Sony MEX-BT3900U Manuale del proprietario

Categoria
Amplificatori audio per auto
Tipo
Manuale del proprietario
FRONT
AUDIO OUT
REAR / SUB
AUDIO OUT
*
4
REMOTE
IN
*
5
EXTERNAL
MICROPHONE
Let op
Installeer dit apparaat in het dashboard van de auto
omdat de achterkant van het apparaat tijdens gebruik
heet kan worden.

Dit apparaat is ontworpen voor gebruik op een
auto-accu van 12 V gelijkstroom, negatieve aarde.

Zorg ervoor dat de draden niet onder een schroef of
tussen bewegende onderdelen (b.v. rail van de
autostoel) terechtkomen.

Voordat u de aansluitingen maakt, moet u het contact
uitzetten om kortsluiting te vermijden.

Sluit de voedingskabel aan op het apparaat en de
luidsprekers voordat u de kabel aansluit op de
hulpvoedingsaansluiting.

Sluit alle aardingskabels op een
gemeenschappelijk aardpunt aan.

Voorzie niet-aangesloten kabels om veiligheidsredenen
altijd van isolatietape.
Opmerkingen bij de voedingskabel (geel)

Wanneer u dit apparaat aansluit samen met andere
stereocomponenten, moet het vermogen van de
aangesloten autostroomkring groter zijn dan de som
van de zekeringen van elke component afzonderlijk.

Wanneer het vermogen van de autostroomkringen
ontoereikend is, moet u het apparaat rechtstreeks
aansluiten op de accu.
Onderdelenlijst

De nummers in de afbeelding verwijzen naar die in de
montage-aanwijzingen.

De beugel wordt op het apparaat bevestigd voordat
dit wordt verzonden. Voordat u het apparaat installeert,
moet u de ontgrendelingssleutels gebruiken om de
beugel van het apparaat te verwijderen. Zie "De
beugel verwijderen ()" op de achterkant van dit vel
voor meer informatie.

Bewaar de ontgrendelingssleutels voor
toekomstig gebruik omdat u deze ook nodig hebt
om het apparaat uit de auto te verwijderen.
Let op
Houd de beugel voorzichtig vast zodat u uw vingers
niet verwondt.
Greep
Opmerking
Voordat u het apparaat installeert, moet u de grepen aan beide zijden
van de beugel 2 mm naar binnen buigen. Als de grepen recht zijn of
naar buiten gebogen, kan het apparaat niet goed worden bevestigd en
kan dit losschieten.
Voorbeeldaansluitingen
Opmerkingen (-
A
)

Sluit eerst de aarddraad aan voordat u de versterker aansluit.

U hoort de pieptoon alleen als de ingebouwde versterker wordt
gebruikt.
Aansluitschema
Naar AMP REMOTE IN van een optionele
eindversterker
Deze aansluiting is alleen bedoeld voor versterkers. Door een ander
systeem aan te sluiten kan het apparaat worden beschadigd.
Naar het interface-snoer van een autotelefoon
Waarschuwing
Indien u een elektrische antenne hebt zonder relaiskast,
kan het aansluiten van dit apparaat met de bijgeleverde
voedingskabel de antenne beschadigen.
Opmerkingen over de bedienings- en voedingskabels

De bedieningskabel voor de elektrische antenne (blauw) levert +12 V
gelijkstroom wanneer u de tuner inschakelt of de AF (Alternative
Frequency)- of TA (Traffic Announcement)-functie activeert.

Wanneer uw auto is uitgerust met een FM/MW/LW-antenne in de
achterruit/zijruit, moet u de bedieningskabel voor de elektrische
antenne (blauw) of de hulpvoedingskabel (rood) aansluiten op de
voedingsingang van de bestaande antenneversterker. Raadpleeg uw
dealer voor meer details.

Met dit apparaat is het niet mogelijk een elektrische antenne zonder
relaiskast te gebruiken.
Instandhouden van het geheugen
Zolang de gele voedingskabel is aangesloten, blijft de stroomvoorziening
van het geheugen intact, ook wanneer het contact van de auto wordt
uitgeschakeld.
Opmerkingen betreffende het aansluiten van de luidsprekers

Zorg dat het apparaat is uitgeschakeld, alvorens de luidsprekers aan
te sluiten.

Gebruik luidsprekers met een impedantie van 4 tot 8 Ohm en let op
dat die het vermogen van de versterker kunnen verwerken. Als u dit
niet doet, kunnen de luidsprekers ernstig beschadigd raken.

Verbind in geen geval de aansluitingen van de luidsprekers met het
chassis van de auto en sluit de aansluitingen van de rechter- en
linkerluidspreker niet op elkaar aan.

Verbind de aarddraad van dit apparaat niet met de negatieve (–)
aansluiting van de luidspreker.

Probeer nooit de luidsprekers parallel aan te sluiten.

Sluit alleen passieve luidsprekers aan. Als u actieve luidsprekers (met
ingebouwde versterkers) aansluit, kan dat leiden tot beschadiging van
het apparaat.

Om defecten te vermijden mag u de bestaande luidsprekerbedrading
in uw auto niet gebruiken wanneer er een gemeenschappelijke
negatieve (–) draad is voor de rechter- en linkerluidsprekers.

Verbind de luidsprekerdraden niet met elkaar.
Opmerking over aansluiten
Als de luidspreker en versterker niet correct zijn aangesloten, wordt
"FAILURE" in het display weergegeven. In dit geval moet u zorgen dat de
luidspreker en versterker correct zijn aangesloten.
Précautions
Installez cet appareil sur le tableau de bord de la
voiture, car larrière de l’appareil chauffe en cours
d’utilisation.

Cet appareil est conçu pour fonctionner uniquement
sur un courant continu de 12 V avec masse négative.

Evitez de coincer les câbles sous des vis ou dans des
pièces mobiles (par exemple, armature de siège).

Avant deffectuer des raccordements, éteignez le
moteur pour éviter les courts-circuits.

Branchez le câble d’alimention sur lappareil et les
haut-parleurs avant de le brancher sur le connecteur
d’alimentation auxiliaire.

Rassemblez tous les câbles de mise à la masse en
un point de masse commun.

Veillez à isoler tout câble lâche non raccordé avec du
ruban isolant.
Remarques sur le câble d’alimentation (jaune)

Lorsque cet appareil est raccordé à d’autres
équipements stéréo, la valeur nominale du circuit
raccordé du véhicule doit être supérieure à la somme
des fusibles de chaque élément.

Si aucun circuit de la voiture nest assez puissant,
raccordez directement lappareil à la batterie.
Liste des composants

Les numéros de la liste correspondent à ceux des
instructions.

Le support est fixé à lappareil en usine. Avant le
montage de l’appareil, utilisez les clés de déblocage
pour détacher le support de l’appareil. Pour de plus
amples informations, reportez-vous à la section
« Retrait du support () » au verso de la feuille.

Conservez les clés de déblocage pour une
utilisation ultérieure car vous en aurez
également besoin pour retirer l’appareil de votre
véhicule.
Avertissement
Manipulez le support avec soin pour éviter de vous
blesser aux doigts.
Loquet
Remarque
Avant l’installation, assurez-vous que les loquets des deux côtés du
support sont bien pliés de 2 mm vers l’intérieur. Si les loquets sont
droits ou pliés vers l’extérieur, l’appareil ne peut pas être fixé solidement
et peut se détacher.
Exemple de raccordement
Remarques (-
A
)

Raccordez d’abord le câble de mise à la masse avant de connecter
l’amplificateur.

L’alarme est émise uniquement lorsque l’amplificateur intégré est
utilisé.
Schéma de raccordement
Vers la prise AMP REMOTE IN d’un amplificateur
de puissance facultatif
Ce raccordement existe seulement pour les amplificateurs. Le
raccordement à tout autre système peut endommager l’appareil.
Vers le câble d'interface d’un téléphone de
voiture
Avertissement
Si vous disposez d’une antenne électrique sans boîtier de
relais, le branchement de cet appareil au moyen du
cordon d’alimentation fourni risque d’endommager
l’antenne.
Remarques sur les câbles de commande et d’alimentation

Le câble de commande d’antenne électrique (bleu) fournit du courant
continu de +12 V lorsque vous mettez le tuner sous tension ou
lorsque vous activez la fonction AF (fréquence alternative) ou TA
(informations de circulation).

Lorsque votre voiture est équipée d’une antenne FM/MW (PO)/LW
(GO) intégrée dans la vitre arrière/latérale, raccordez le câble de
commande d’antenne électrique (bleu) ou le câble d’alimentation des
accessoires (rouge) au bornier de l’amplificateur d’antenne existant.
Pour plus de détails, consultez votre revendeur.

Une antenne électrique sans boîtier de relais ne peut pas être utilisée
avec cet appareil.
Raccordement pour la conservation de la mémoire
Lorsque le câble d’alimentation jaune est raccordé, le circuit de la
mémoire est alimenté en permanence même si la clé de contact est en
position d’arrêt.
Remarques sur le raccordement des haut-parleurs

Avant de raccorder les haut-parleurs, mettre l’appareil hors tension.

Utiliser des haut-parleurs ayant une impédance de 4 à 8 ohms et une
capacité adéquate sous peine de les endommager.

Ne pas raccorder les bornes du système de haut-parleurs au châssis
de la voiture et ne pas connecter les bornes du haut-parleur droit à
celles du haut-parleur gauche.

Ne pas raccorder le câble de mise à la masse de cet appareil à la
borne négative (–) du haut-parleur.

Ne pas tenter de raccorder les haut-parleurs en parallèle.

Connecter uniquement des haut-parleurs passifs. La connexion de
haut-parleurs actifs (avec des amplificateurs intégrés) aux bornes des
haut-parleurs pourrait endommager l’appareil.

Pour éviter tout problème de fonctionnement, n’utilisez pas les câbles
des haut-parleurs intégrés (–) installés dans votre voiture si l’appareil
dispose d’un câble négatif commun pour les haut-parleurs droit et
gauche.

Ne raccordez pas entre eux les cordons des haut-parleurs de
l’appareil.
Remarque sur le raccordement
Si les haut-parleurs et l’amplificateur ne sont pas raccordés
correctement, le message « FAILURE » s’affiche. Dans ce cas,
assurez-vous que les haut-parleurs et l’amplificateur sont raccordés
correctement.
Warnhinweise
Installieren Sie das Gerät unbedingt im
Armaturenbrett des Fahrzeugs, denn die Rückseite des
Geräts erwärmt sich bei Betrieb.

Dieses Gerät ist ausschließlich für den Betrieb bei 12 V
Gleichstrom (negative Erdung) bestimmt.

Achten Sie darauf, dass die Kabel nicht unter einer
Schraube oder zwischen beweglichen Teilen wie
z. B. in einer Sitzschiene eingeklemmt werden.

Schalten Sie, bevor Sie irgendwelche Anschlüsse
vornehmen, die Zündung des Fahrzeugs aus, um
Kurzschlüsse zu vermeiden.

Verbinden Sie das Stromversorgungskabel mit dem
Gerät und den Lautsprechern, bevor Sie es mit dem
Hilfsstromanschluss verbinden.

Schließen Sie alle Erdungskabel an einen
gemeinsamen Massepunkt an.

Aus Sicherheitsgründen müssen alle losen, nicht
angeschlossenen Drähte mit Isolierband abgeklebt
werden.
Hinweise zum Stromversorgungskabel (gelb)

Wenn Sie dieses Gerät zusammen mit anderen
Stereokomponenten anschließen, muss der
Autostromkreis, an den die Geräte angeschlossen sind,
eine höhere Leistung aufweisen als die Summe der
Sicherungen der einzelnen Komponenten.

Wenn kein Autostromkreis eine so hohe Leistung
aufweist, schließen Sie das Gerät direkt an die Batterie
an.
Teileliste

Die Nummern in der Liste sind dieselben wie im
Erläuterungstext.

Die Halterung wird vor dem Ausliefern am Gerät
angebracht. Bevor Sie das Gerät montieren, nehmen Sie
die Halterung mithilfe der Löseschlüssel vom
Gerät ab. Einzelheiten dazu finden Sie unter
„Abnehmen der Halterung ()“ auf der Rückseite
dieses Blattes.

Bewahren Sie die Löseschlüssel für den
späteren Gebrauch auf. Sie werden
z. B. benötigt, wenn Sie das Gerät aus dem
Fahrzeug ausbauen wollen.
Vorsicht
Seien Sie beim Umgang mit der Halterung vorsichtig,
damit Sie sich nicht die Hände verletzen.
Verriegelung
Hinweis
Vergewissern Sie sich vor dem Installieren, dass die Verriegelungen an
beiden Seiten der Halterung um 2 mm nach innen gebogen sind.
Wenn die Verriegelungen gerade oder nach außen gebogen sind, lässt
sich das Gerät nicht sicher installieren und kann herausspringen.
Anschlussbeispiel
Hinweise (-
A
)

Schließen Sie unbedingt zuerst das Massekabel an, bevor Sie den
Verstärker anschließen.

Der Warnton wird nur ausgegeben, wenn der integrierte Verstärker
verwendet wird.
Anschlussdiagramm
An AMP REMOTE IN des gesondert erhältlichen
Endverstärkers
Dieser Anschluss ist ausschließlich für Verstärker gedacht. Schließen
Sie nichts anderes daran an. Andernfalls kann das Gerät beschädigt
werden.
An Schnittstellenkabel eines Autotelefons
Warnung
Wenn Sie eine Motorantenne ohne Relaiskästchen
verwenden, kann durch Anschließen dieses Geräts mit
dem mitgelieferten Stromversorgungskabel die
Antenne beschädigt werden.
Hinweise zu den Steuer- und Stromversorgungsleitungen

Die Motorantennen-Steuerleitung (blau) liefert +12 V Gleichstrom,
wenn Sie den Tuner einschalten oder die AF- (Alternativfrequenzsuche)
oder die TA-Funktion (Verkehrsdurchsagen) aktivieren.

Wenn das Fahrzeug mit einer in der Heck-/Seitenfensterscheibe
integrierten FM (UKW)/MW/LW-Antenne ausgestattet ist, schließen Sie
die Motorantennen-Steuerleitung (blau) oder die
Zubehörstromversorgungsleitung (rot) an den
Stromversorgungsanschluss des vorhandenen Antennenverstärkers
an. Näheres dazu erfahren Sie bei Ihrem Händler.

Es kann nur eine Motorantenne mit Relaiskästchen angeschlossen
werden.
Stromversorgung des Speichers
Wenn die gelbe Stromversorgungsleitung angeschlossen ist, wird der
Speicher stets (auch bei ausgeschalteter Zündung) mit Strom versorgt.
Hinweise zum Lautsprecheranschluss

Schalten Sie das Gerät aus, bevor Sie die Lautsprecher anschließen.

Verwenden Sie Lautsprecher mit einer Impedanz zwischen 4 und 8
Ohm und ausreichender Belastbarkeit. Ansonsten können die
Lautsprecher beschädigt werden.

Verbinden Sie die Lautsprecheranschlüsse nicht mit dem
Wagenchassis und verbinden Sie auch nicht die Anschlüsse des
rechten mit denen des linken Lautsprechers.

Verbinden Sie die Masseleitung dieses Geräts nicht mit dem negativen
(–) Lautsprecheranschluss.

Versuchen Sie nicht, Lautsprecher parallel anzuschließen.

An die Lautsprecheranschlüsse dieses Geräts dürfen nur
Passivlautsprecher angeschlossen werden. Schließen Sie keine
Aktivlautsprecher (Lautsprecher mit eingebauten Verstärkern) an, da
das Gerät sonst beschädigt werden könnte.

Um Fehlfunktionen zu vermeiden, verwenden Sie nicht die im
Fahrzeug installierten, integrierten Lautsprecherleitungen, wenn am
Ende eine gemeinsame negative (–) Leitung für den rechten und den
linken Lautsprecher verwendet wird.

Verbinden Sie nicht die Lautsprecherkabel des Geräts miteinander.
Hinweis zum Anschließen
Wenn Lautsprecher und Verstärker nicht richtig angeschlossen sind,
erscheint „FAILURE“ im Display. Vergewissern Sie sich in diesem Fall, dass
Lautsprecher und Verstärker richtig angeschlossen sind.
Attenzione
Assicurarsi di installare l’apparecchio nel cruscotto
dell’auto, poiché la parte posteriore dellapparecchio
stesso si surriscalda durante luso.

Questo apparecchio è stato progettato per l’uso solo a 12
V CC con massa negativa.

Evitare che i cavi rimangano bloccati da una vite o
incastrati nelle parti mobili (ad esempio nelle guide
scorrevoli dei sedili).

Prima di effettuare i collegamenti, spegnere il motore
dell’automobile onde evitare di causare cortocircuiti.

Collegare il cavo di alimentazione all’apparecchio e ai
diffusori prima di collegarlo al connettore di
alimentazione ausiliaria.

Portare tutti i cavi di messa a terra a un punto di
massa comune.

Per sicurezza, assicurarsi di isolare qualsiasi cavo non
collegato utilizzando del nastro adesivo.
Note sul cavo di alimentazione (giallo)

Se questo apparecchio viene collegato in combinazione
con altri componenti stereo, la potenza nominale dei
circuiti dellautomobile deve essere superiore a quella
prodotta dalla somma dei fusibili di ciascun
componente.

Se la potenza nominale dei circuiti dellautomobile non è
sufficiente, collegare l’apparecchio direttamente alla
batteria.
Elenco dei componenti

I numeri nella lista corrispondono a quelli riportati nelle
istruzioni.

La staffa è applicata all’unità prima della spedizione.
Prima di montare l’unità, utilizzare le chiavette di
rilascio per rimuovere la staffa dall’unità. Per
ulteriori informazioni, vedere “Rimozione della staffa
()” sul lato opposto del foglio.

Conservare le chiavette di rilascio per un uso
futuro in quanto sono necessarie per rimuovere
l’unità dall’auto.
Attenzione
Maneggiare la staffa con cautela per evitare di ferirsi le
mani.
Fermo
Nota
Prima di installare l’unità, accertarsi di ripiegare i fermi presenti su
entrambi i lati della staffa verso l’interno di 2 mm. Se i fermi sono diritti
o ripiegati verso l’esterno, l’apparecchio non verrà installato in modo
sicuro e potrebbe fuoriuscire.
Esempio di collegamento
Note (-
A
)

Assicurarsi di collegare il cavo di terra prima di collegare l’apparecchio
all’amplificatore.

L’allarme viene emesso solo se è in uso l’amplificatore incorporato.
Schema di collegamento
A AMP REMOTE IN di un amplificatore di potenza
opzionale
Questo collegamento è riservato esclusivamente agli amplificatori.
Non collegare un tipo di sistema diverso onde evitare di causare
danni all’apparecchio.
Al cavo di interfaccia di un telefono per auto
Avvertenza
Quando si collega l’apparecchio con il cavo di
alimentazione in dotazione , si potrebbe danneggiare
l’antenna elettrica se questa non dispone di scatola a relè.
Note sui cavi di controllo e di alimentazione

Il cavo (blu) di controllo dell’antenna elettrica fornisce alimentazione
pari a +12 V CC quando si attiva il sintonizzatore oppure la funzione TA
(notiziario sul traffico) o AF (frequenza alternativa).

Se l’automobile è dotata di antenna FM/MW/LW incorporata nel vetro
posteriore/laterale, collegare il cavo (blu) di controllo dell’antenna
elettrica o il cavo (rosso) di ingresso dell’alimentazione accessoria al
terminale di alimentazione del preamplificatore dell’antenna esistente.
Per ulteriori informazioni, consultare il proprio fornitore.

Non è possibile usare un’antenna elettrica senza scatola a relè con
questo apparecchio.
Collegamento per la conservazione della memoria
Quando il cavo di ingresso alimentazione giallo è collegato, viene sempre
fornita alimentazione al circuito di memoria anche quando l’interruttore
di accensione è spento.
Note sul collegamento dei diffusori

Prima di collegare i diffusori spegnere l’apparecchio.

Usare diffusori di impedenza compresa tra 4 e 8 ohm e con capacità di
potenza adeguata, altrimenti i diffusori potrebbero venire danneggiati.

Non collegare i terminali del sistema diffusori al telaio dell’auto e non
collegare i terminali del diffusore destro a quelli del diffusore sinistro.

Non collegare il cavo di terra di questo apparecchio al terminale
negativo (–) del diffusore.

Non collegare i diffusori in parallelo.

Assicurarsi di collegare soltanto diffusori passivi, poiché il collegamento
di diffusori attivi, dotati di amplificatori incorporati, ai terminali dei
diffusori potrebbe danneggiare l’apparecchio.

Per evitare problemi di funzionamento, non utilizzare i cavi dei diffusori
incorporati installati nell’automobile se l’apparecchio condivide un
cavo comune negativo (–) per i diffusori destro e sinistro.

Non collegare fra loro i cavi dei diffusori dell’apparecchio.
Nota sui collegamenti
Se l’amplificatore e il diffusore non sono collegati correttamente,
“FAILURE” viene visualizzato nel display. In tal caso, accertarsi che
l’amplificatore e il diffusore siano collegati correttamente.
Cautions
Be sure to install this unit in the dashboard of the car
as the rear side of the unit becomes hot during use.

This unit is designed for negative ground (earth) 12 V
DC operation only.

Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).

Before making connections, turn the car ignition off to
avoid short circuits.

Connect the power supply lead to the unit and
speakers before connecting it to the auxiliary power
connector.

Run all ground (earth) leads to a common ground
(earth) point.

Be sure to insulate any loose unconnected leads with
electrical tape for safety.
Notes on the power supply lead (yellow)

When connecting this unit in combination with other
stereo components, the connected car circuits rating
must be higher than the sum of each components fuse.

When no car circuits are rated high enough, connect
the unit directly to the battery.
Parts list

The numbers in the list are keyed to those in the
instructions.

The bracket is attached to the unit before shipping.
Before mounting the unit, use the release keys to
remove the bracket from the unit. For details, see
“Removing the bracket ()” on the reverse side of the
sheet.

Keep the release keys for future use as they are
also necessary if you remove the unit from your
car.
Caution
Handle the bracket carefully to avoid injuring your
fingers.
Catch
Note
Before installing, make sure that the catches on both sides of the bracket
are bent inwards 2 mm (
3
/32 in). If the catches are straight or bent
outwards, the unit will not be installed securely and may spring out.
Connection example
Notes (-
A
)

Be sure to connect the ground (earth) lead before connecting the
amplifier.

The alarm will only sound if the built-in amplifier is used.
Connection diagram
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting any other system
may damage the unit.
To the interface cable of a car telephone
Warning
If you have a power antenna (aerial) without a relay box,
connecting this unit with the supplied power supply lead
may damage the antenna (aerial).
Notes on the control and power supply leads

The power antenna (aerial) control lead (blue) supplies +12 V DC when
you turn on the tuner, or when you activate the AF (Alternative
Frequency) or TA (Traffic Announcement) function.

When your car has built-in FM/MW/LW antenna (aerial) in the rear/
side glass, connect the power antenna (aerial) control lead (blue) or
the accessory power supply lead (red) to the power terminal of the
existing antenna (aerial) booster. For details, consult your dealer.

A power antenna (aerial) without a relay box cannot be used with this
unit.
Memory hold connection
When the yellow power supply lead is connected, power will always be
supplied to the memory circuit even when the ignition switch is turned
off.
Notes on speaker connection

Before connecting the speakers, turn the unit off.

Use speakers with an impedance of 4 to 8 ohms, and with adequate
power handling capacities to avoid its damage.

Do not connect the speaker terminals to the car chassis, or connect the
terminals of the right speakers with those of the left speaker.

Do not connect the ground (earth) lead of this unit to the negative (–)
terminal of the speaker.

Do not attempt to connect the speakers in parallel.

Connect only passive speakers. Connecting active speakers (with
built-in amplifiers) to the speaker terminals may damage the unit.

To avoid a malfunction, do not use the built-in speaker leads installed
in your car if the unit shares a common negative (–) lead for the right
and left speakers.

Do not connect the unit’s speaker leads to each other.
Note on connection
If speaker and amplifier are not connected correctly, “FAILURE” appears
in the display. In this case, make sure the speaker and amplifier are
connected correctly.
× 2
Positions 1, 2, 3, and 6 do not have pins.
An Position 1, 2, 3 und 6 befinden sich keine Stifte.
Les positions 1, 2, 3 et 6 ne comportent pas de broches.
Le posizioni 1, 2, 3 e 6 non hanno piedini.
De posities 1, 2, 3 en 6 hebben geen pins.
4
Yellow
Gelb
Jaune
Giallo
Geel
continuous power supply
permanente Stromversorgung
alimentation continue
alimentazione continua
continue voeding
7
Red
Rot
Rouge
Rosso
Rood
switched power supply
geschaltete Stromversorgung
alimentation commutée
alimentazione commutata
geschakelde voeding
5
Blue
Blau
Bleu
Blu
Blauw
power antenna (aerial) control
Motorantennensteuerung
commande d'antenne électrique
comando dell’antenna elettrica
aansturing elektrische antenne
8
Black
Schwarz
Noir
Nero
Zwart
ground (earth)
Masse
masse
terra
aarding
Negative polarity positions 2, 4, 6, and 8 have striped leads.
An den negativ gepolten Positionen 2, 4, 6 und 8 befinden sich gestreifte Adern.
Les positions de polarité négative 2, 4, 6 et 8 sont dotées de cordons rayés.
Le posizioni a polarità negativa 2, 4, 6 e 8 hanno cavi rigati.
De posities voor negatieve polariteit (2, 4, 6 en 8) hebben gestreepte kabels.
1
Purple
Violett
Violet
Viola
Paars
+
Speaker, Rear, Right
Lautsprecher hinten rechts
Haut-parleur, arrière, droit
Diffusore, posteriore, destro
Luidspreker, achter, rechts
5
White
Weiß
Blanc
Bianco
Wit
+
Speaker, Front, Left
Lautsprecher vorne links
Haut-parleur, avant, gauche
Diffusore, anteriore, sinistro
Luidspreker, voor, links
2
Speaker, Rear, Right
Lautsprecher hinten rechts
Haut-parleur, arrière, droit
Diffusore, posteriore, destro
Luidspreker, achter, rechts
6
Speaker, Front, Left
Lautsprecher vorne links
Haut-parleur, avant, gauche
Diffusore, anteriore, sinistro
Luidspreker, voor, links
3
Gray
Grau
Gris
Grigio
Grijs
+
Speaker, Front, Right
Lautsprecher vorne rechts
Haut-parleur, avant, droit
Diffusore, anteriore, destro
Luidspreker, voor, rechts
7
Green
Grün
Vert
Verde
Groen
+
Speaker, Rear, Left
Lautsprecher hinten links
Haut-parleur, arrière, gauche
Diffusore, posteriore, sinistro
Luidspreker, achter, links
4
Speaker, Front, Right
Lautsprecher vorne rechts
Haut-parleur, avant, droit
Diffusore, anteriore, destro
Luidspreker, voor, rechts
8
Speaker, Rear, Left
Lautsprecher hinten links
Haut-parleur, arrière, gauche
Diffusore, posteriore, sinistro
Luidspreker, achter, links
Fuse (10 A)
Sicherung (10 A)
Fusible (10 A)
Fusibile (10 A)
Zekering (10 A)
from the car’s power connector
vom Stromanschluss des Fahrzeugs
du connecteur d’alimentation de la voiture
dal connettore di alimentazione dell’auto
van de autovoedingsaansluiting
See “Power connection diagram” on the reverse side for details.
Näheres dazu finden Sie im „Stromanschlussdiagramm“. Blättern Sie
dazu bitte um.
Voir le « Schéma de raccordement d’alimentation » au verso pour plus
de détails.
Per ulteriori informazioni, vedere “Diagramma dei collegamenti di
alimentazione” che si trova sul retro.
Zie "Voedingsaansluitschema" op de achterkant voor meer details.
from the car’s speaker connector
vom Lautsprecheranschluss des Fahrzeugs
du connecteur de haut-parleur de la voiture
dal connettore dei diffusori dell’auto
van de autoluidsprekeraansluiting
*
2
from car antenna (aerial)
von Autoantenne
de l’antenne de la voiture
dall’antenna dell’auto
van een auto-antenne
*
3
*
3
*
1
Speaker impedance: 4 – 8 ohms × 4
*
2
Note for the antenna (aerial) connecting
If your car antenna (aerial) is an ISO (International
Organization for Standardization) type, use the
supplied adaptor to connect it. First connect
the car antenna (aerial) to the supplied adaptor,
then connect it to the antenna (aerial) jack of the
master unit.
*
3
RCA pin cord (not supplied)
*
4
AUDIO OUT can be switched SUB or REAR. For
details, see the supplied Operating Instructions.
*
5
Separate adaptor may be required.
*
1
Lautsprecherimpedanz: 4 – 8 Ohm × 4
*
2
Hinweis zum Anschließen der Antenne
Wenn Ihre Autoantenne der ISO-Norm
(Internationale Normungsgemeinschaft)
entspricht, schließen Sie sie mithilfe des
mitgelieferten Adapters an. Verbinden Sie
zuerst die Autoantenne mit dem mitgelieferten
Adapter und verbinden Sie diesen dann mit der
Antennenbuchse des Hauptgeräts.
*
3
Cinchkabel (nicht mitgeliefert)
*
4
AUDIO OUT kann zwischen SUB und REAR
umgeschaltet werden. Näheres hierzu finden Sie in
der mitgelieferten Bedienungsanleitung.
*
5
Möglicherweise ist ein separater Adapter
erforderlich.
*
1
Impédance des haut-parleurs : 4 – 8 ohms × 4
*
2
Remarque sur le raccordement de l’antenne
Si votre antenne de voiture est de type ISO
(Organisation internationale de normalisation),
utilisez l’adaptateur fourni pour la raccorder.
Raccordez d’abord l’antenne de voiture à
l’adaptateur fourni et, ensuite, à la prise d’antenne
de l’appareil principal.
*
3
Cordon à broche RCA (non fourni)
*
4
AUDIO OUT peut être commuté sur SUB ou REAR.
Pour obtenir plus de détails, reportez-vous au
mode d’emploi.
*
5
Un adaptateur séparé peut être nécessaire.
*
1
Impedenza diffusori: 4 – 8 ohm × 4
*
2
Nota per il collegamento dell’antenna
Se l’antenna dell’auto è di tipo ISO (International
Organization for Standardization), utilizzare
l’adattatore in dotazione per collegarla.
Collegare prima l’antenna della macchina
all’adattatore in dotazione, quindi collegarla alla
presa dell’antenna dell’apparecchio principale.
*
3
Cavo a piedini RCA (non in dotazione)
*
4
AUDIO OUT può essere impostato su SUB o su
REAR. Per ulteriori informazioni, consultare il
manuale di istruzioni per l’uso in dotazione.
*
5
Potrebbe essere necessario un adattatore
separato.
*
1
Luidsprekerimpedantie: 4 – 8 ohm × 4
*
2
Opmerking bij de antenne-aansluiting
Indien uw auto is uitgerust met een antenne van
het type ISO (International Organization for
Standardization), moet u die aansluiten met
behulp van de bijgeleverde adapter . Sluit eerst
de auto-antenne aan op de bijgeleverde adapter
en vervolgens de antennestekker op het
hoofdtoestel.
*
3
Tulpstekkersnoer (niet bijgeleverd)
*
4
AUDIO OUT kan worden ingesteld op SUB of REAR.
Raadpleeg de gebruiksaanwijzing voor meer
informatie.
*
5
Er is mogelijk een afzonderlijke adapter vereist.
REAR
/
SUB
AUDIO OUT
REAR
/
SUB
AUDIO OUT
A
Equipment used in illustrations (not supplied)
In Abbildungen dargestellte Geräte (nicht mitgeliefert)
Appareils utilisés dans les illustrations (non fournis)
Apparecchiatura utilizzata nelle illustrazioni (non in dotazione)
Apparatuur gebruikt in de afbeeldingen (niet bijgeleverd)
Front speaker
Frontlautsprecher
Haut-parleur avant
Diffusore anteriore
Voorluidspreker
Power amplifier
Endverstärker
Amplificateur de puissance
Amplificatore di potenza
Eindversterker
Rear speaker
Hecklautsprecher
Haut-parleur arrière
Diffusore posteriore
Achterluidspreker
Active subwoofer
Aktiver Tiefsttöner
Caisson de graves actif
Subwoofer attivo
Actieve subwoofer
AMP REM
Light blue
Hellblau
Bleu ciel
Azzurro
Lichtblauw
Blue/white striped
Blauweiß gestreift
Rayé bleu/blanc
Rigato blu e bianco
Blauw/wit gestreept
AT T
Max. supply current 0.3 A
max. Versorgungsstrom 0,3 A
Courant d’alimentation maximum 0,3 A
Alimentazione massima fornita 0,3 A
Max. voedingsstroom 0,3 A
4-199-773-11(1)
Installation/Connections
Installation/Anschluss
Installation/Connexions
Installazione/Collegamenti
Montage/Aansluitingen
Bluetooth
®
Audio System
MEX-BT3900U
B
©2010 Sony Corporation Printed in Thailand
Microphone XA-MC10
Mikrofon XA-MC10
Microphone XA-MC10
Microfono XA-MC10
Microfoon XA-MC10
*
1
Power connection diagram
Auxiliary power connector may vary depending on the
car. Check your car’s auxiliary power connector diagram
to make sure the connections match correctly. There are
three basic types (illustrated below). You may need to
switch the positions of the red and yellow leads in the car
stereos power supply lead.
After matching the connections and switched power
supply leads correctly, connect the unit to the car’s power
supply. If you have any questions and problems
connecting your unit that are not covered in this manual,
please consult the car dealer.
Auxiliary power connector
Hilfsstromanschluss
Connecteur d’alimentation auxiliaire
Connettore di alimentazione ausiliaria
Hulpvoedingsaansluiting
Red
Rot
Rouge
Rosso
Rood
Red
Rot
Rouge
Rosso
Rood
Yellow
Gelb
Jaune
Giallo
Geel
Yellow
Gelb
Jaune
Giallo
Geel
Red
Rot
Rouge
Rosso
Rood
Red
Rot
Rouge
Rosso
Rood
Yellow
Gelb
Jaune
Giallo
Geel
Yellow
Gelb
Jaune
Giallo
Geel
Red
Rot
Rouge
Rosso
Rood
Red
Rot
Rouge
Rosso
Rood
Yellow
Gelb
Jaune
Giallo
Geel
Yellow
Gelb
Jaune
Giallo
Geel
Voedingsaansluitschema
De hulpvoedingsaansluiting kan verschillen afhankelijk
van de auto. Controleer het hulpvoedingsaansluitschema
dat bij dit apparaat wordt geleverd om te zien of de
aansluitingen kloppen. Er zijn drie basistypes (zie
afbeelding hieronder). Het is mogelijk dat u de posities
van de rode en gele kabels in de voedingskabel van het
audiosysteem van de auto moet omwisselen.
Als de aansluitingen en geschakelde voedingskabels
kloppen, sluit u het apparaat aan op de voeding van de
auto. Indien u nog vragen of problemen hebt in verband
met het aansluiten van het apparaat die niet in deze
handleiding worden behandeld, raadpleeg dan de
autodealer.
Diagramma dei collegamenti
di alimentazione
Il connettore di alimentazione ausiliaria può variare a
seconda della macchina. Controllare il diagramma del
connettore di alimentazione ausiliaria della macchina per
essere sicuri che i collegamenti corrispondano
correttamente. Vi sono tre tipi di base (illustrazione
sotto). Potrà essere necessario cambiare le posizioni dei
fili rosso e giallo nel cavo di alimentazione dello stereo
della macchina.
Dopo aver fatto corrispondere i collegamenti e aver
commutato i cavi di alimentazione, collegare
l’apparecchio all’alimentazione della macchina. Se si
hanno domande o se sorgono problemi che non sono
stati trattati nel manuale nel collegare lapparecchio,
contattare lautoconcessionario.
Schéma de raccordement
d’alimentation
Le connecteur d’alimentation auxiliaire peut varier
suivant le type de voiture. Vérifiez le schéma du
connecteur dalimentation auxiliaire de votre voiture pour
vous assurer que les connexions correspondent. Il en
existe trois types de base (illustrés ci-dessous). Il se peut
que vous deviez commuter la position des fils rouge et
jaune du câble d’alimentation de l’autoradio.
Après avoir établi les connexions et commuté
correctement les câbles d’alimentation, raccordez
l’appareil à l’alimentation de la voiture. Si vous avez des
questions ou des difficultés à propos de cet appareil qui
ne sont pas abordées dans le présent mode d’emploi,
consultez votre concessionnaire automobile.
Stromanschlussdiagramm
Der Hilfsstromanschluss kann je nach Fahrzeugtyp
unterschiedlich sein. Sehen Sie im Hilfsstroman-
schlussdiagramm für Ihr Fahrzeug nach, wie die
Verbindung ordnungsgemäß vorgenommen werden
muss. Es gibt, wie unten abgebildet, drei grundlegende
Typen. Sie müssen möglicherweise die rote und gelbe
Leitung des Stromversorgungskabels der
Autostereoanlage vertauschen.
Stellen Sie die Anschlüsse her, schließen Sie die
geschalteten Stromversorgungsleitungen richtig an und
verbinden Sie dann das Gerät mit der Stromversorgung
Ihres Fahrzeugs. Wenn beim Anschließen des Geräts
Fragen oder Probleme auftreten, die in dieser Anleitung
nicht erläutert werden, wenden Sie sich bitte an den
Autohändler.
Précautions

Choisir soigneusement l’emplacement de l’installation
afin que lappareil ne gêne pas la conduite normale du
véhicule.

Eviter d’installer l’appareil dans un endroit exposé à de
la poussière, de la saleté, des vibrations violentes ou à
des températures élevées, comme en plein soleil ou à
proximité dun conduit de chauffage.

Pour garantir un montage sûr, n’utiliser que le matériel
fourni.
Réglage de l’angle de montage
Ajuster l’inclinaison à un angle inférieur à 45°.
Retrait du support
Avant d’installer l’appareil, retirez le support de
l’appareil.
1 Insérez les deux clés de déblocage
simultanément entre l’appareil et le support
jusqu’au déclic indiquant qu’elles sont en place.
2 Tirez le support vers le bas, puis tirez
l’appareil vers le haut pour les séparer.
Exemple de montage
Installation dans le tableau de bord
Remarques

Pliez ces griffes vers l’extérieur pour assurer une prise correcte si
nécessaire (-2).

Assurez-vous que les 4 loquets du tour de protection sont
correctement insérés dans les fentes de l’appareil (-3).
Retrait et fixation de la façade
Avant d’installer l’appareil, retirez la façade.
-A Pour la retirer
Avant de retirer la façade, veillez à appuyer sur la touche
 et à la maintenir enfoncée. Appuyez sur
, puis sortez la façade en tirant vers vous.
-B Pour la fixer
Fixez la partie de la façade sur la partie de
l’appareil, comme indiqué sur l’illustration, puis appuyez
sur le côté gauche jusquau déclic.
Avertissement au cas où le
contact de votre voiture ne
dispose pas d’une position
ACC
Veillez à régler la fonction de mise hors tension
automatique. Pour obtenir davantage d’informations,
reportez-vous au mode d’emploi fourni.
Lappareil séteint complètement et automatiquement
après le laps de temps choisi une fois lappareil mis hors
tension afin d’éviter que la batterie ne se décharge.
Si vous ne réglez pas la fonction de mise hors tension
automatique, appuyez sur la touche  et
maintenez-la enfoncée jusquà ce que l’affichage
disparaisse à chaque fois que vous coupez le contact.
Touche RESET
Une fois que l’installation et les raccordements sont
terminés, retirez la façade et appuyez sur le bouton
RESET à laide d’un stylo à bille ou d’un autre objet
pointu.
Precautions

Choose the installation location carefully so that the
unit will not interfere with normal driving operations.

Avoid installing the unit in areas subject to dust, dirt,
excessive vibration, or high temperature, such as in
direct sunlight or near heater ducts.

Use only the supplied mounting hardware for a safe and
secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 45°.
Removing the bracket
Before installing the unit, remove the bracket
from the unit.
1 Insert both release keys together between
the unit and the bracket until they click.
2 Pull down the bracket , then pull up the unit
to separate.
Mounting example
Installation in the dashboard
Notes

Bend these claws outward for a tight fit, if necessary (-2).

Make sure that the 4 catches on the protection collar are properly
engaged in the slots of the unit (-3).
How to detach and attach the
front panel
Before installing the unit, detach the front panel.
-A To detach
Before detaching the front panel, be sure to press and
hold . Press
, and pull it off towards
you.
-B To attach
Engage part of the front panel with part of the unit,
as illustrated, and push the left side into position until it
clicks.
Warning if your car’s ignition
has no ACC position
Be sure to set the Auto Off function. For details, see the
supplied Operating Instructions.
The unit will shut off completely and automatically in the
set time after the unit is turned off, which prevents
battery drain.
If you do not set the Auto Off function, press and hold
 until the display disappears each time
you turn the ignition off.
RESET button
When the installation and connections are completed, be
sure to press the RESET button with a ball-point pen, etc.,
after detaching the front panel.
Sicherheitshinweise

Wählen Sie den Einbauort sorgfältig so aus, dass das
Gerät beim Fahren nicht hinderlich ist.

Bauen Sie das Gerät so ein, dass es keinen hohen
Temperaturen (keinem direkten Sonnenlicht, keiner
Warmluft von der Heizung), keinem Staub, keinem
Schmutz und keinen starken Vibrationen ausgesetzt ist.

Für eine sichere Befestigung verwenden Sie stets die
mitgelieferten Montageteile.
Hinweis zum Montagewinkel
Das Gerät sollte in einem Winkel von weniger als 45°
montiert werden.
Abnehmen der Halterung
Nehmen Sie vor dem Installieren des Geräts die
Halterung vom Gerät ab.
1 Führen Sie beide Löseschlüssel zwischen dem
Gerät und der Halterung ein, bis sie mit
einem Klicken einrasten.
2 Ziehen Sie die Halterung nach unten und das
Gerät nach oben, um die beiden zu trennen.
Montagebeispiel
Installation im Armaturenbrett
Hinweise

Falls erforderlich, biegen Sie diese Klammern für einen sicheren Halt
nach außen (-2).

Achten Sie darauf, die 4 Verriegelungen an der Schutzumrandung
korrekt in die Aussparungen am Gerät einzusetzen (-3).
Abnehmen und Anbringen
der Frontplatte
Nehmen Sie die Frontplatte vor dem Einbau des
Geräts ab.
-A Abnehmen
Halten Sie vor dem Abnehmen der Frontplatte unbedingt
 gedrückt. Drücken Sie
und ziehen Sie
sie auf sich zu heraus.
-B Anbringen
Setzen Sie Teil der Frontplatte wie in der Abbildung
dargestellt an Teil des Geräts an und drücken Sie die
linke Seite der Frontplatte an, bis sie mit einem Klicken
einrastet.
Warnhinweis, wenn die
Zündung Ihres Fahrzeugs nicht
über eine Zubehörposition
(ACC oder I) verfügt
Aktivieren Sie unbedingt die Abschaltautomatik. Näheres
dazu finden Sie in der mitgelieferten
Bedienungsanleitung.
Nach dem Ausschalten wird das Gerät dann nach der
voreingestellten Zeit automatisch vollständig
abgeschaltet, so dass der Autobatterie kein Strom mehr
entzogen wird.
Wenn Sie die Abschaltautomatik nicht aktivieren, müssen
Sie jedes Mal, wenn Sie die Zündung ausschalten, die
Taste  gedrückt halten, bis die Anzeige
ausgeblendet wird.
Taste RESET
Wenn Sie das Gerät eingebaut und alle Anschlüsse
vorgenommen haben, müssen Sie die Frontplatte
abnehmen und mit einem Kugelschreiber oder einem
anderen spitzen Gegenstand die Taste RESET drücken.
Precauzioni

Scegliere con attenzione la posizione per l’installazione
in modo che l’apparecchio non interferisca con le
operazioni di guida del conducente.

Evitare di installare lapparecchio dove sia soggetto ad
alte temperature, come alla luce solare diretta o al getto
di aria calda dell’impianto di riscaldamento, o dove
possa essere soggetto a polvere, sporco e vibrazioni
eccessive.

Usare solo il materiale di montaggio in dotazione per
un’installazione stabile e sicura.
Regolazione dell’angolo di montaggio
Regolare langolo di montaggio in modo che sia inferiore
a 45°.
Rimozione della staffa
Prima di installare l’unità, rimuovere la staffa
dall’unità.
1 Inserire contemporaneamente entrambe le
chiavette di rilascio tra l’apparecchio e la
staffa fino a che non scattano in posizione.
2 Estrarre la staffa , quindi sollevare
l’apparecchio per rimuoverlo.
Esempio di montaggio
Installazione nel cruscotto
Note

Piegare verso l’esterno questi morsetti per un’installazione più sicura,
se necessario (-2).

Assicurarsi che i 4 fermi sulla cornice protettiva siano
correttamente inseriti negli alloggiamenti dell’apparecchio (-3).
Come rimuovere e reinserire il
pannello anteriore
Prima di installare l’apparecchio rimuovere il
pannello anteriore.
-A Per rimuoverlo
Prima di rimuovere il pannello anteriore, assicurarsi di
tenere premuto . Premere
, quindi
tirare verso di sé il pannello anteriore.
-B Per reinserirlo
Applicare la parte del pannello anteriore alla parte
dell’apparecchio come mostrato nell’illustrazione e
premere il lato sinistro fino a sentire uno scatto.
Avvertenza relativa all’installazione
su unauto sprovvista della
posizione ACC (accessoria) sul
blocchetto di accensione
Accertarsi di impostare la funzione di spegnimento
automatico. Per ulteriori informazioni, fare riferimento
alle istruzioni per l’uso in dotazione.
Lapparecchio si spegne completamente e
automaticamente all’ora impostata dopo che è stato
disattivato, onde evitare che la batteria si scarichi.
Se la funzione di spegnimento automatico non è stata
impostata, ogni volta che il motore viene spento tenere
premuto  finché il display non viene
disattivato.
Tasto RESET
Una volta completate le procedure di installazione e i
collegamenti, accertarsi di premere il tasto RESET con
una penna a sfera o un oggetto simile dopo avere rimosso
il pannello anteriore.
1
2 3
A
B
Dashboard
Armaturenbrett
Tableau de bord
Cruscotto
Dashboard
Fire wall
Motorraumtrennwand
Paroi ignifuge
Parete tagliafiamma
Brandschot
Claws
Klammern
Griffes
Morsetti
Klemhaken
Voorzorgsmaatregelen

Kies de installatieplaats zorgvuldig zodat het apparaat
de bestuurder niet hindert tijdens het rijden.

Installeer het apparaat niet op plaatsen waar het
blootgesteld wordt aan hoge temperaturen, b.v. in
direct zonlicht of bij de warme luchtstroom van de
autoverwarming, aan sterke trillingen, of waar het in
contact komt met veel stof of vuil.

Gebruik voor het veilig en stevig monteren van het
apparaat uitsluitend de bijgeleverde montage-
onderdelen.
De montagehoek bepalen
Zorg dat de montagehoek minder dan 45° bedraagt.
De beugel verwijderen
Voordat u het apparaat installeert, moet u de
beugel van het apparaat verwijderen.
1 Plaats de ontgrendelingssleutels tussen het
apparaat en de beugel tot deze vastklikken.
2 Trek de beugel omlaag en trek het apparaat
omhoog om deze van elkaar te scheiden.
Montagevoorbeeld
Montage in het dashboard
Opmerkingen

Indien nodig kunt u deze klemhaken ombuigen voor een steviger
bevestiging (-
2
).

De 4 grepen op de beschermende rand moeten goed in de sleuven
van het apparaat zijn geplaatst (-
3
).
Het voorpaneel verwijderen
en bevestigen
Verwijder, alvorens met het installeren te
beginnen, het voorpaneel.
-A Verwijderen
Voordat u het voorpaneel verwijdert, moet u
 ingedrukt houden. Druk op
en trek
het voorpaneel naar u toe.
-B Bevestigen
Breng deel van het voorpaneel aan op deel van het
apparaat zoals afgebeeld en druk op de linkerzijde tot
deze vastklikt.
Waarschuwing als het
contactslot van de auto geen
ACC-positie heeft
Zorg ervoor dat u de functie voor automatisch
uitschakelen instelt. Raadpleeg de bijgeleverde
gebruiksaanwijzing voor meer informatie.
Het apparaat wordt na de ingestelde tijd automatisch
volledig uitgeschakeld nadat het apparaat is
uitgeschakeld. Zo wordt voorkomen dat de accu
leegloopt.
Als u de functie voor automatisch uitschakelen niet
instelt, moet u  ingedrukt houden tot
het display verdwijnt telkens wanneer u het contact
uitschakelt.
RESET-toets
Als u de installatie en aansluitingen hebt voltooid, moet
u met een puntig voorwerp, zoals de punt van een
balpen, op RESET drukken nadat u het voorpaneel hebt
verwijderd.
the car without ACC position
Fahrzeug ohne Zubehörposition (ACC oder I)
Véhicule sans position ACC
Auto priva della posizione ACC
Auto zonder ACC-positie
4
Yellow
Gelb
Jaune
Giallo
Geel
continuous power supply
permanente Stromversorgung
alimentation continue
alimentazione continua
continue voeding
7
Red
Rot
Rouge
Rosso
Rood
switched power supply
geschaltete Stromversorgung
alimentation commutée
alimentazione commutata
geschakelde voeding
4
Yellow
Gelb
Jaune
Giallo
Geel
switched power supply
geschaltete Stromversorgung
alimentation commutée
alimentazione commutata
geschakelde voeding
7
Red
Rot
Rouge
Rosso
Rood
continuous power supply
permanente Stromversorgung
alimentation continue
alimentazione continua
continue voeding
Face the hook inwards.
Der Haken muss nach innen
weisen.
Tournez le crochet vers
l’intérieur.
Con il gancetto rivolto verso
l’interno.
Het haakje moet naar binnen
wijzen.
1 / 1

Sony MEX-BT3900U Manuale del proprietario

Categoria
Amplificatori audio per auto
Tipo
Manuale del proprietario