Hoover HDSV985B AUS Manuale utente

1

ǼȁȁǾȃǿȀǹǼīȋǼǿȇǿǻǿȅȋȇǾȈǾȈȀǹǿǼīȀǹȉǹȈȉǹȈǾȈ

ENGLISH INSTALLATION AND USER’S MANUAL

FRENCH NOTICE D’INSTALLATION ET D’UTILISATION

ITALIAN MANUALE D’ISTRUZIONE

GERMAN NOTICE D’INSTALLATION ET D’UTILISATION

DUTCH HANDLEIDING VOOR INSTALLATIE EN

GEBRUIK

2

INSTALLATION AND USER’S MANUAL

CONTENT

INTRODUCTION 03

SAFETY PRECAUTION 03

SPECIFICATION 05

INSTALLATION (VENT OUTSIDE) 06

INSTALLATION (VENT INSIDE) 10

DESCRIPTION OF COMPONENTS 11

OPERATION 11

MAINTENANCE 13

TROBULESHOOTING 14

CONFORMITY WITH DIRECTIVES 15

ENVIRONMENTAL PROTECTION 15

3

INTRODUCTION

Thank you for choosing this cooker hood.

This instruction manual is designed to provide you with all required

instructions related to the installation, use and maintenance of the appliance.

In order to operate the unit correctly and safety, please read this instruction

manual carefully before installation and usage.

The cooker hood uses high quality materials, and is made with a streamlined

design. Equipped with large power electric motor and centrifugal fan, it also

provides strong suction power, low noise operation, non-stick grease filter and

easy assembly installation.

By placing the

marking on this product, we declare, on our own

responsibility, compliance to all of European safety, health and environmental

requirements stated in the legislation for this product.

SAFETY PRECAUTION

Never let the children operate the machine.

The cooker hood is for home use only, not suitable for barbecue, roast

shop and other commercial purpose.

The cooker hood and its filter should be clean regularly in order to

keep in good working condition.

Clean the cooker hood according to the instruction manual and keep

the unit from danger of burning.

Forbid the direct baking from the gas cooker.

Please keep the kitchen room a good convection.

Before connecting this appliance check that the power supply cord is

not damaged. A damage supply cord must be replaced by qualified

service personnel only.

There shall be adequate ventilation of the room when the range hood

is used at the same time as appliances burning gas or other fuels;

The air must not be discharged into a flue that is used for exhausting

fumes from appliances burning gas or other fuels;

Regulations concerning the discharge of air have to be fulfilled.

Children should be supervised to ensure that they do not play with the

appliance.

Do not flambé under the range hood.

The range hood is not intended to be installed over a hob having more

than four hob elements

4

Electrical Shock Hazard



Only plug this unit into a properly earthed outlet. If in doubt seek

advice from a suitably qualified engineer.



Failure to follow these instructions can result in death, fire, or

electrical shock.

5

Standard Installation Accessories List

Spec.

Illustration Picture

Qty

Casing

1

Upper Chimney

1

Lower Chimney

1

Lower chimney bracket

1

Upper chimney bracket

1

Hanging Board

1

φ8 rawl plugs

φ8×φ6 white color

9

Screws

ST4.0×30

9

φ7.2screws

ST4.0×8

2

6

INSTALLATION

˄

wall mounting

˅

If you have an outlet to the outside, your cooker hood can be connected as

below picture by means of an extraction duct (enamel, aluminum, flexible pipe

non flammabe with an interior diameter of 150mm)

1. Before installation, turn the unit off and unplug it from the outlet.

2. The cooker hood should be placed at a distance of 65~75cm above

the cooking plane for best effect.

3. Drill 3 x 8mm holes to accommodate the bracket. Screw and tighten

the bracket onto the wall with the screws provided.

Wall plug

Wall bracket

107.5mm

Screw(4mm x 30mm)

7

4. Leave up the cooker hood and hang onto the wall bracket hook.

5. Fix the one-way-valve to the air outlet of the cooker hood. Then,

attached the exhaust pipe onto the one-way-valve as shown below.

Exhaust pipe

Cooker hood

8

6.

i. Place the glass in appropriate position on the top the cooker

hood.

ii. Fix with 4 screws and washer. In order to avoid the glass

cracking, please do not tighten the screws too strongly.

i. By Put the inner chimney into outer chimney .Then pulling out

the inner chimney upwards. Adjust to reach the height required.

ii. Sliding the chimney to adjust the chimney height. When the

height you required is reached, then hang the fixing hole to the fixing

screws as showed in below pictures.

Inner chimney

Outer chimney

9

8.

i. Drill 2 x 8mm holes to accommodate the plate II. Screw and

tighten the plate II onto the wall with 2 screws provided.

ii. Assembly the chimney onto the unit and fix it with 2 screws.

Plate II

Wall plug

Screw

4mm x 8mm

Screw

(4mm x 30mm)

10

INSTALLATION (VENT INSIDE)

If you do not have an outlet to the outside, exhaust pipe is not required and

the installation is similar to the one show in section “INSTALLATION (VENT

OUTSIDE)”.

Activated carbon filter can be used to trap odors.

In order to install the activated carbon filter, the grease filter should be

detached first. Press the lock and pull it downward.

Plug the activated carbon filter into the unit and turn it in clockwise direction.

Repeat the same on the other side.

NOTE:

o Make sure the filter is securely locked. Otherwise, it would loosen and

cause dangerous.

o When activated carbon filter attached, the suction power will be

lowere

11

DESCRIPTION OF COMPONENTS

OPERATION

Low Speed button 1

It’s used for Ventilation on the kitchen. It is suitable for simmering and

cooking which do not make much steam.

Medium Speed button 2

Airflow speed is ideally for ventilation in standard cooking operation.

High Speed button 3

When high density of smoke or steam produced, press high-speed button

for highest effective ventilation.

Light button

NOTE: If Low / Medium / High speed buttons are press at the same time,

the unit will only operate at the highest speed.

12

ON/OFF button

Pressing 1-2 seconds to switch on/off the cooker hood.

Low Speed button

It’s used for Ventilation on the kitchen. It is suitable for simmering and

cooking which do not make much steam.

Medium Speed button

Airflow speed is ideally for ventilation in standard cooking operation.

High Speed button

When high density of smoke or steam produced, press high-speed button

for highest effective ventilation.

Light button

Short press the light/timer button ( 1 second) to switch on or switch off the

light.

Quick Timer

.Keep pressing the Light/timer button for 2-3 seconds to switch on the

quick timer.

The working speed button will become flashing, the quick timer will last for

5 seconds.

When the count down finish, there will be ‘bit’ sounds for 5 seconds.

To cancel the quick timer, press Light/Timer button again or press the

ON/OFF button.

13

STANDBY MODE.

After plug in, all lighting, system in STANDBY MODE.

Low Speed button

cooking which do not make much steam.

Medium Speed button

Airflow speed is ideally for ventilation in standard cooking operation.

High Speed button

When high density of smoke or steam produced, press high-speed button

for high effective ventilation.

Booster button

Depress this button to enter into highest speed and again to turn off motor.

Light button

14

MAINTENANCE

Before cleaning switch the unit off and pull out the plug.

I. Regular Cleaning

Use a soft cloth moistened with hand-warm mildly soapy water or

household cleaning detergent. Never use metal pads, chemical, abrasive

material or stiff brush to clean the unit.

II. Monthly Cleaning for Grease Filter

ESSENTIAL: Clean the filter every month can prevent any risk of fire.

The filter collects grease, smoke and dust…... so the filter is directly

affecting the efficiency of the cooker hood. If not cleaned, the grease

residue (potential flammable) will saturate on the filter. Clean it with

household cleaning detergent.

III. Annual Cleaning for Activated Carbon Filter

Apply SOLELY to unit that installed as a recirculation unit (not vented to

the outside). This filter traps odors and must be replaced at least once a

year

depending on how frequent the cooker hood used.

IV. Changing a light bulb

Remove the screws on the glass, take off the hood glass. Find the

bulb that requires replacement, you will find it located in the light

fixture which is inside the exposed section of the canopy.

Disconnect the light wiring point and remove the bulb holders and

wiring from the hood. Important: It’s not possible to replace the bulbs

individually, it will be necessary to obtain the bulbs, bulb holders and

wiring as a complete part. (LED light: MAX 1.5W)

Fit the replacement bulbs, bulb holders and wiring in the same

manners as the originals. Then reconnect the light wiring point.

15

Refit the hood glass and fasten the glass screws. Make sure the screws are

fully tightened.

TROBULESHOOTING

Fault

Cause

Solution

Light on, but

fan does not

work

The fan blade is

jammed.

Switch off the unit and repair by

qualified service personnel only.

The motor is damaged.

Both light and

fan do not

work

Halogen light bulb burn.

Replace the bulb with correct

rating.

Power cord looses.

Plug in to the power supply again.

Serious

Vibration of

the unit

The fan blade is

damaged.

Switch of the unit and repair by

qualified service personnel only.

The fan motor is not

fixed tightly.

Switch off the unit and repair by

qualified service personnel only.

The unit is not hung

properly on the bracket.

Take down the unit and check

whether the bracket is in proper

location.

Suction

performance

not good

Too long distance

between the unit and

the cooking plane

Readjust the distance to 65

-

75cm

CUSTOMER ASSISTANCE SERVICE

If you cannot identify the cause of the operating anomaly, switch off the

appliance and contact the Assistance Service.

PRODUCT SERIAL NUMBER. Where can I find it?

It is important you to inform the Assistance Service of your product code

and its serial number (a 16 character code which begins with the number 3);

this can be found on the guarantee certificate or on the data plate located

on the appliance.

It will help to avoid wasted journeys to technicians, thereby (and most

significantly) saving the corresponding callout charges.

This appliance is marked according to the European directive

2012/19/EU on Waste Electrical and Electronic Equipment

(WEEE).

WEEE contains both polluting substances (which can cause

negative consequences for the environment) and basic components (which

can be re-used). It is important to have WEEE subjected to specific

16

treatments, in order to remove and dispose properly all pollutants, and

recover and recycle all materials.

Individuals can play an important role in ensuring that WEEE does not

become an environmental issue; it is essential to follow some basic rules:

WEEE should not be treated as household waste;

WEEE should be handed over to the relevant collection points managed by

the municipality or by registered companies. In many countries, for large

WEEE, home collection could be present.

In many countries, when you buy a new appliance, the old one may be

returned to the retailer who has to collect it free of charge on a one-to-one

basis, as long as the equipment is of equivalent type and has the same

functions as the supplied equipment.

17

NOTICE D’INSTALLATION ET D’UTILISATION

Sommaire

INTRODUCTION

17

Conseils pour la sécurité

17

Cahier des charges 18

Installation (Evacuation) 20

Installation (Recyclage) 24

Description des composants 25

Fonctionnement 26

Entretien 26

Dépannage 27

Service après ventes 28

Protection de l’environnement 29

18

Introduction

Merci d‘avoir choisi cette hotte.

Ce manuel d'instructions est conçu pour vous fournir toutes les

instructions requises relatives à l'installation, l'utilisation et l'entretien de

l'appareil. Afin de faire fonctionner l'appareil correctement et en toute

sécurité, merci de lire attentivement ce manuel avant l'installation et

l'utilisation.

La hotte utilise des matériaux de haute qualité avec un design épuré.

Equipé d’un moteur électrique de grande puissance et d’un ventilateur

centrifuge, il fournit également une puissance d'aspiration forte, un

fonctionnement avec un bruit modéré, un filtre à graisse et un montage

facile.

En plaçant le marquage sur ce produit

, nous déclarons, sous

notre propre responsabilité, le respect à tous de la sécurité européenne,

la santé et les exigences environnementales énoncées dans la législation

pour ce produit.

Avertissement de sécurité

x Ne pas laisser d’enfants utiliser l’appareil

x Cette hotte est dédiée à un usage domestique uniquement. Elle

ne doit pas être utilisée pour les barbecues, les rôtisseries ou

toutes autres activités

x La hotte et ses filtres doivent être nettoyés régulièrement pour en

garantir un bon état de fonctionnement

x Respecter les consignes de ce manuel pour le nettoyage de la

hotte afin d’empêcher tout risque d’incendie

x Merci de garder une ventilation dans la cuisine

x Avant de connecter cet appareil, contrôlez que le cordon

d'alimentation n'est pas endommagé. Un cordon d'alimentation

endommagé doit être remplacé par une personne qualifiée.

x Il doit y avoir une ventilation adéquate de la pièce quand la hotte

est utilisée en même temps que des appareils utilisant du gaz ou

d'autres combustibles

x l'air ne doit pas être évacué par un conduit qui est utilisé pour

évacuer les fumées des appareils utilisant le gaz ou d'autres

combustibles

19

x La réglementation concernant le rejet de l’air doit être satisfaite

x Cet appareil n’est pas destiné à être utilisé par des personnes

(notamment les enfants) incapables, irresponsables ou sans

connaissance sur l’utilisation du produit, à moins qu’elle ne soit

surveillées ou instruites sur l’utilisation de l’appareil par une

personne responsable de leur sécurité

x Les enfants doivent être surveillés pour s'assurer qu'ils ne jouent

pas avec l'appareil.

x Ne pas faire flamber sous la hotte

x La hotte n'est pas destinée à être installé au-dessus d’une plaque

de cuisson ayant plus de quatre foyers de cuisson

Risque de choc électrique

x Cette hotte ne peut être branchée seulement sur une prise reliée

à la terre. En cas de doute, demandez conseil à un ingénieur

qualifié

x Le non-respect de ces instructions peut entraîner la mort, un

incendie ou un choc électrique.

20

Liste d’accessoires pour l’installation

Caractérisriques

Visuels

Qty

Base

1

Cheminée haute

1

Cheminée basse

1

Support de la cheminée basse

1

Support de la cheminée haute

1

Fixation murale

1

φ8 chevilles

φ8×φ6 blanches

9

Vis

ST4.0×30

9

φ7.2 Vis

ST4.0×8

2

Installation (évacuation externe)

Si vous avez une évacuation vers l’extérieur, la hotte pourra être installée

comme suit au moyen d’un conduit d’extraction (émail, aluminium, tuyau

flexible et non inflammable avec un diamètre intérieur de 150mm).

La pagina sta caricando ...

Hoover HDSV985B AUS Manuale utente

Questo manuale è adatto anche per

Hoover HDSV985B AUS Manuale utente

Documenti correlati

Altri documenti