Hotpoint ET6004X Guida utente

Marca: Hotpoint

Modello: ET6004X

Categoria: Piani cottura

Tipo: Guida utente

Questo manuale è adatto anche per

ET7424 (T)

Instructions for Installation and Use

Electric Hob

Model: ET7424-ET6004

The Recipe Book

Hotpoint has come up with a small recipe book - which is practical, full of helpful tips and easy to use - to help you

rediscover the delights of cooking.

It contains a wide variety of handy tips to keep in mind to try out new dishes effortlessly.

It also has 15 recipes preprogrammed into the oven, so thanks to the interactive display, once you have done the

preparation all you have to do is make one simple selection.

kitchen think

To the Installer

Before installation fill in the product details on the back cover this book.

The information can be found on the rating plate.

To the User

You must read the instructions prior to installing and using the appliance and

then retain them for future reference.

CONTENTS

Retention of this Instruction Book

This Instruction Book must be kept handy for reference as it contains important details on the safe and proper use of

the appliance.

If you sell or pass the appliance to someone else, or move house and leave it behind, make sure this Book is also

provided so the new owner can become familiar with the appliance and safety warnings.

If the Book is lost or damaged a copy may be obtained from:

INDESIT Company UK LTD, Morley Way, Peterborough, PE2 9JB

Introduction

Advice and recommendations

Installation and fastening

Electrical connection

Cooking zone description

The controls

Operation

The safety devices

Maintenance and care

After Sales Service

Hotpoint Guarantee

Key Contacts

Back Cover

Your new hob is guaranteed* and will give lasting service. This guarantee is only applicable if the appliance has been

installed in accordance with the installation instructions detailed in this booklet.

To help make best use of your cooking equipment, please read this booklet carefully.

The hob is designed specifically for domestic use and responsibility will not be accepted for use in any other installation.

Introduction

* The guarantee is subject to the provisions that the appliance:

(a) Has been used solely in accordance with this booklet.

(b) Has been properly connected to a suitable supply voltage as stated on the rating plate, attached to the

appliance.

manufacturers authorised employee or agent.

(d) Has been correctly installed.

This appliance conforms with the following European Economic Community directives:

- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications;

- 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications;

- 90/396/EEC of 29/06/90 (Gas) and subsequent modifications;

- 93/68/EEC of 22/07/93 and subsequent modifications.

Advice and recommendations

• This appliance was designed for non-professional,

household use.

• Before using the appliance, read the instructions in the

owner’s manual carefully since it contains all the instruc-

tions you require to ensure safe installation, use and

maintenance. Keep this owner’s manual in a safe place

for future reference.

• When you have removed the packing, check whether

the appliance is intact. If you have any doubts, contact

a qualified professional before using the appliance.

• Never leave the packing components (plastic bags, poly-

styrene foam, nails, etc.) within the reach of children

since these are a source of potential danger.

• The appliance must be installed by a qualified techni-

cian in compliance with the instructions provided by the

manufacturer.

• The latter denies all responsibility for improper installa-

tion which may harm persons and animals and damage

property.

• The electrical safety of this appliance can only be guar-

anteed if the latter is correctly and efficiently earthed, in

compliance with regulations on electrical safety. Always

ensure that this vital safety measure has been taken. If

you have any doubts, call in a qualified technician to

check the electrical system thoroughly.

• The manufacturer denies all responsibility for damage

resulting from a system which has not been earthed cor-

rectly.

• Before powering the appliance, check whether the tech-

nical characteristics featured on the appliance data plate

correspond with those of the mains electrical system.

• Check that the current load of the mains supply and of

the power sockets is suitable for the maximum power of

the appliance, indicated on the appliance data plate. If in

doubt, contact a qualified professional.

• This appliance must only be used for the purpose for

which it was expressly designed. Any other use (such

as heating a room for example) is considered to be im-

proper and consequently dangerous.

• The manufacturer denies all responsibility for damage

resulting from improper or incorrect use of the appliance.

First use: the glue used on the hob seals may leave greasy traces on the glass surface. We recommend you wipe these

off before using the appliance, with the aid of a non abrasive cleaner. During the first few hours of use, you may detect

a smell of rubber, which will disappear quickly.

• Certain fundamental rules must be followed when using

electrical appliances. The following are of particular im-

portance:

• do not touch the appliance with wet or damp hands,

• never use the appliance when barefoot,

• never use extensions,

• never pull on the power supply cable or the appliance

itself to unplug it from the mains socket,

• never leave the appliance exposed to atmospheric agents

(rain, sun, etc.),

• do not allow children or persons who are not familiar with

the appliance to use it without supervision.

• Always unplug the appliance from the mains or switch

off the main switch before cleaning or performing any

cleaning or maintenance operations.

• If the surface of the glass cracks, unplug the appli-

ance immediately. For any repairs, contact only an au-

thorised after-sales service centre and demand original

spare parts. Failure to comply with the above may com-

promise the safety of the appliance.

• Cut the power supply cable after disconnecting it from

the power mains when you decide not to use the appli-

ance any longer. Also make all potentially dangerous

parts of the appliance safe, above all for children who

could play with the appliance.

• The glass ceramic hob is resistant to thermal and me-

chanical shocks. However, it may break due to a shock

caused by a sharp object, such as a tool for exam-

ple. In this case, unplug the appliance immediately

and contact an authorised after-sales service centre

to have it repaired.

• Remember that the heating area stays hot for at least

half an hour after being turned off; please refrain from

placing any cookware or other items on the cooking zone

while still hot.

• Do not turn on the heating zones if aluminium foil or

plastic items have been placed on the hob surface.

• Do not go near the heating zones when these are still

hot.

• If you use small electric appliances near the hob, make

sure their power supply cable does not come into con-

tact with the hot parts of the hob.

• Make sure all pan handles are always pointing inwards

towards the centre of the hob to prevent any accidental

spills.

The following instructions are intended for a qualified fitter

to guide him/her along the installation, adjustment and tech-

nical maintenance procedures as correctly as possible and

in full compliance with the applicable norms in force.

Important : unplug the hob before all operations.

Installation

• This hob can be built into a worktop simply by cutting

out the corresponding slot.

• The worktop must be made with a material designed

to withstand a temperature of approximately 100°C.

• The hob should be positioned at least 40 mm away

from the back wall or any other vertical surface in

order to allow for correct ventilation and to prevent

the surfaces around the appliance from overheating.

• If you wish to install the hob on top of an oven, the

latter must be fitted with a cooling fan.

• Try to avoid installing the hob on top of a dishwasher;

if this is unavoidable, place a watertight separating

element between the two appliances.

Fastening

Very important: It is vital that you ensure the glass ce-

ramic hob is built into a perfectly flat supporting surface.

Deformations due to improper fastening could alter the

characteristics of the hob and compromise its perform-

ance.

The fastening springs are fastened by screws (see dia-

gram).

It is vital that these screws be kept accessible at all

times.

Insert the hob into the cut-out slot, applying pressure all

along the perimeter of the hob frame so that the latter

adheres fully to the worktop.

FRONT OF HOB

KITCHEN

WORKTOP

REAR SPRING ASSEMBLY

HOB FROM BELOW

Installation and fastening

Distance to

keep between the

cut-out slot and

the cabinet

690

520

560 +/- 1

490 +/- 1

785

750 +/- 1

510

490+/- 1

Electrical connection

This appliance conforms with the following European

Community Directives:

- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent

amendments;

- 89/336/EEC of 03/05/89 (Electromagnetic compatibility)

and subsequent amendments;

- 93/68/EEC of 22/07/93 and subsequent amendments;

- 2002/96/EC

The European Directive 2002/96/EC on Waste Electrical

and Electronic Equipment (WEEE), requires that old

household electrical appliances must not be disposed of

in the normal unsorted municipal waste stream. Old

appliances must be collected separately in order to optimise

the recovery and recycling of the materials they contain

and reduce the impact on human health and the

environment. The crossed out “wheeled bin” symbol on the

product reminds you of your obligation, that when you di-

spose of the appliance it must be separately collected.

Consumers should contact their local authority or retailer

for information concerning the correct disposal of their old

appliance.

Warning: If the hob is fitted above a built-in oven, the hob

and the oven must be connected to the mains separately

for safety reasons and to simplify operations when it is

necessary to pull the oven out for some reason.

• The electrical safety of this appliance can only be guar-

anteed if the latter is correctly and efficiently earthed,

in compliance with regulations on electrical safety. Al-

ways ensure that this vital safety measure has been

taken. If you have any doubts, call in a qualified techni-

cian to check the electrical system thoroughly.

• The manufacturer denies all responsibility for damage

resulting from a system which has not been earthed

correctly.

• Before powering the appliance, check whether the tech-

nical characteristics featured on the appliance data plate

correspond with those of the mains electrical system.

• Check that the current load of the mains supply and of

the power sockets is suitable for the maximum power

of the appliance, indicated on the appliance data plate.

If in doubt, contact a qualified professional.

Disconnect the appliance from the electricity supply

before all operations.

Connect your hob to the electrical system by means of a

junction box: if the appliance is connected permanently

to the mains, an omnipolar circuit breaker, accessible if

necessary, with a minimum contact opening of 3 mm should

be installed.

Valid only for models without a power supply cable

Some models are not fitted with a power supply cable, as

the cable should be sized according to the type of electrical

connection in use (see connection table below). To connect

the cable, proceed as follows:

• Using a screwdriver, prise on the side tabs of the terminal

board cover;

• Pull open the cover of the terminal board.

L N

1 2 3 4 5

To install the cable, proceed as follows:

• unscrew the wire clamp screw and the contact screws.

• to make the desired electrical connection (see table),

use the jumpers housed inside the box. Position the

power supply cable wires according to the indications

in the table.

• once the connections have been made, tighten all the

terminal screws fully.

• Fasten the supply cable in place with the clamp and

close the cover of the terminal board.

Electrical connections

Voltage,

Frequency

Fuses,

Sections

230V-1+N~50 Hz

25 A*

2,5 mm²

* Application of the simultaneity coefficient in accordance with

cei 60335-2-6 norm

Cooking zone description

Induction is the fastest cooking method available.

Unlike traditional cooking zones, the induction zone does not heat up the glass surface. The pan itself is the heating

element: the pan evenly transfers heat to its contents as long as it is made of ferromagnetic material.

Each zone is controlled:

• by a selector key whose silk screen printing reproduces the cooking zone drawing,

• and by a power adjustment set comprising two parts (+,-).

As long as the temperature of the cooking zones remains above 60°C, even after use, the residual heat indicators stay

on(the power display indicates H) to prevent the risk of burns.

HOBS ET 6004 ET 7424

Cooking zones Power (in W) Power (in W)

Back Right (BR)

I 1800 I 2400 – B 3000*

Front Right (FR)

I 1200 I 1200 – 600 if BR*

Front Left (FL)

I 1800 IO 1200/2400 – B 3000*

Back Left (BL)

I 1200 I 1200 – 600

Overall power 6000 7200

single induction zone

oval induction zone

B 3000*

è the zone can be boosted to 3000 W

600 if BR*

the power of the cooking zone is reduced to 600 W as long as the BR zone is boosted

(for example)

The controls

Booster

15.

2 2

6 5

1. ON/OFF key

2. Cooking zone selector keys

3. Power (from 0 to 9) and residual heat indicators (H)

4. Zone selection indicator:

• on: the corresponding zone is selected and can be

modified,

• off: the corresponding zone is not selected, no modi-

fication can be made.

5. Power increase key

6. Power decrease key

7. Timer control key for cooking time programming (only

on hobs fitted with a timer)

8. Programmed cooking time indicator

9. Indicator light corresponding to the programmed cook-

ing zone

10.Booster key

11.Controls lock key

12.Lock indicator light

Operation

Controls lock

When the hob is in use, you can lock the controls to avoid

any accidental changes to the settings (by children or when

cleaning, for example).

Just press the key, the indicator light next to the key

lights up and the controls are locked.

To change the power level setting or stop cooking, the

controls have to be unlocked: press the key, the indi-

cator light turns off and the controls are unlocked.

To access the setting of a cooking zone again, select the

zone by pressing the corresponding control key.

Cooking time programming

you may programme all the cooking zones simultaneously

for a maximum cooking time of 99 minutes.

Proceed as follows:

• select the cooking zone by pressing the corresponding

control key,

• set the desired heating power using the “+” and “-”

keys,

• press the programming key ,

• set the desired cooking time using the “+” and “-” keys,

• confirm your programming by pressing the programming

key again.

The countdown begins immediately.

The end of programmed cooking is signalled by a beep

(one minute long) and the cooking zone concerned is turned

off.

When you connect the hob to the power supply, a beep

will sound after a few seconds: you can now turn the hob

on.

Turning on the hob

Press key to turn the hob on.

Cooking zone control

Each cooking zone is operated by a control key and by a

power adjustment set (+ and -).

Turning on a cooking zone

• To turn a cooking zone on, press the corresponding con-

trol key and set the desired heating power (from 0 to 9)

using the “+” and “-” keys.

• To set the maximum power directly (9), press key “-”

briefly.

Turning off a cooking zone

To turn off a cooking zone, press the corresponding con-

trol key and:

• press both “+” and “-” simultaneously: the cooking

zone power drops immediately to zero and the zone

is turned off.

• or press the “-” key: the heating power drops progres-

sively until the zone eventually turns off.

Turning off the hob

Press the key; the appliance has been turned off.

If you have locked the hob controls (see paragraph be-

low), the same will still be locked when you turn the hob

back on. Unlock the controls in order to operate the cook-

ing zones.

The booster

To speed up the rise in temperature of the cooking zones

(see cooking zone table on the previous page), press the

Booster

key.

The power display will indicate “P”. The booster function

comes to an automatic stop after 4 minutes.

When the booster function is on, certain cooking zones

(see the cooking zone table on the previous page) are

limited to a maximum power of 600W.

The safety devices

Acoustic signal

Anomalies such as:

• an object (such as a saucepan or a lid, etc.) placed

for more than 10 seconds on the control zone,

• boiled-over liquids or food spilled on the control zone,

• prolonged pressure on a key,...

could cause a beep to sound and the hob to turn off.

To stop the beep from sounding, remove the cause of the

malfunction.

To use the hob, turn it back on and re-select the cooking

zone(s) you wish to use. Set the desired heating power.

Safety cut out

Your appliance is fitted with a safety cut out which inter-

venes after a certain amount of time (see table below)

depending on the power setting. When the safety cut out

has intervened, the power display indicates “0”.

for example: the back right cooking zone is set to 5 and

the front left zone is set to 2. The back right zone will turn

off after 3 hours of operation and the front left zone will

turn off after 10 hours of operation.

To unlock the controls, turn the hob off by pressing the

key.

Overheating protection device

Should your appliance’s electronic components overheat,

the hob will turn off automatically and “—” will come up on

the power level display.

The letter will disappear as soon as the temperature drops

back down to an acceptable level.

Power level Maximum duration of operation

1-2 10 hours

3 5 hours

4 4 hours

5-6 3 hours

7-8 2 hours

9 1 hour

Pan recognition

Each induction cooking zone is fitted with a pan recogni-

tion device. The cooking zone only provides heat in the

presence of a pan which is suitable for the cooking zone.

A blinking pan recognition indicator could signal:

• that the pan is made of unsuitable material, which is

not ferromagnetic,

• that the diameter of the pan is too small,

• that the pan has been removed.

Always match the diameter of the pan with that of the

cooking zones.

Warning: oval cooking zones

Oval cooking zones can only be boosted if the full oval is

enabled.

Do not place two small saucepans on oval cooking zones.

What cookware to use

Given that induction only exists when the magnetic field

is sealed by a metallic recipient, the pan stops being heated

as soon as it is taken off the cooking zone.

Use cookware made of material which is compatible

with induction (ferromagnetic material).

Cast iron, enamelled steel or special induction stain-

less steel saucepans are ideal.

Copper, ceramic, earthenware, glass, terracotta, aluminium

and non magnetic stainless steel cookware is incompat-

ible with induction cooking.

The easiest way to find out whether the pan is suitable

is with a magnet. If the magnet is attracted by the pan

bottom and stays “stuck” to the same, the pan is made of

ferromagnetic material and can be used on your induction

hob.

We recommend you use pans with a very flat and thick

bottom and avoid at all costs all cookware with irregular

rough bases which could scratch the glass surface.

SUITABLE

UNSUITABLE

Cast iron

Enamelled steel

Special stainless steel

Copper,

Aluminium, Glass, Earthenware,

Ceramic, non magnetic Stainless steel

For the attention of wearers of pacemakers or other

active implants:

The hob complies with all current standards on

electromagnetic interference. Your induction hob is therefore

perfectly in keeping with legal requirements (89/336/CEE

directives). It is designed not to create interference on any

other electrical apparatus being used on condition that the

apparatus in question also complies with this legislation.

Your induction hob generates short-range magnetic fields.

To avoid any interference between your induction hob and

a pacemaker, the latter must be designed to comply with

relevant regulations. In this respect, we can only guarantee

our own product conformity. Please consult the pacemaker

manufacturer or your doctor concerning its conformity or

any possible incompatibility.

Hob care

The vitroceramic glass used for the heating surface is

smooth and poreless and it is also resistant to thermal

shocks and to mechanical shocks under normal condi-

tions of use. In order to preserve these properties, we rec-

ommend you care for your hob as follows:

• for ordinary maintenance, just wipe it with a damp

sponge and dry it thoroughly using paper towels.

• If the hob is dirty, rub clean using a special cleaner

suitable for vitroceramic glass, rinse off and dry thor-

oughly.

• food residue and dirt can be removed using a special

scraper. Do this as soon as possible, do not wait for

the hob to cool down in order to avoid incrustations.

For excellent results, use a special stainless steel

wool pad for vitroceramic glass cleaning soaked in

soapy water.

• When the hob is clean, you can apply a special prod-

uct for the care and protection of the same: this type

of product leaves an invisible film on the surface of

the hob to protect the same against any spills and

boiled-over food. It is best if you do this when the

hob is lukewarm or cold.

• Make sure you always rinse the hob with clean water

and dry it thoroughly: otherwise the cleaning prod-

ucts could become encrusted onto the hob during

subsequent cooking.

Recommendations

• Never use abrasive or corrosive substances, such

as aerosol cleaners for grills and ovens, stain remov-

ers or rust removers, scouring powders and abrasive

sponges: even the delicate ones could scratch the

hob surface irreversibly.

• We recommend you keep all items which could melt

away from the hob, such as plastic utensils, sugar

or products with a high sugar content. Should liq-

uid boil over onto the hob surface, remove it immedi-

ately (while the hob is still hot) using a razor blade

scraper, in order to avoid damaging the surface.

• Use this hob exclusively for cooking. Do not place

items on the hob when the same is not in use. Do not

use the hob as a work surface (by placing lids, sauce-

pans or dishcloths on it, for example), nor as a chop-

ping board.

• Never leave aluminium wrappers, aluminium foil and

plastic cookware on the hob when hot or still warm.

• Do not use steam cleaners or high pressure cleaners

to clean your appliance.

• Do not place metal items on the hob (such as knives,

spoons, lids, etc.).

• Never heat up unopened tins: they could burst.

The guarantee does not cover damage to the hob caused

by incorrect use.

Maintenance and care

Advice on using your appliance

To get the best from your hob, it is vital that you follow a

few fundamental rules during cooking and when preparing

food.

• Use pans with a flat bottom so they adhere fully to the

heating zone.

• Always use pans whose diameter covers the cooking

zone fully so that all the available heat can be used.

• Make sure the pan base is always clean and dry, to

guarantee good contact and long life for the cooking

zones and pans alike.

• Avoid using pans used normally on gas burners. The

concentration of heat on gas burners can warp the

bottom of the pan, consequently you would never obtain

the desired result when using the pan on the glass

ceramic hob.

• Never leave a cooking zone on without a pan on it as

the maximum heat level would be reached very quickly,

which could damage the heating elements.

• The glass ceramic hob is resistant to thermal and

mechanical shocks. However, it may break due to a

shock caused by a sharp object. In this case, unplug

the appliance immediately and contact an authorised

after-sales service centre to have it repaired.

Always keep your hob clean. Before proceeding with main-

tenance operations, check that all the cooking zones are

turned off and have cooled down completely.

Stainless steel frame (only on some models)

Stainless steel can stain as an effect of enduring contact

with limescale in water or as an effect of highly aggres-

sive detergents (containing phosphorus). We recommend

you rinse and dry it thoroughly after maintenance. It is

preferable to remove any water spills immediately.

"No company is better positioned to offer an after sales service on a

Hotpoint appliance than us - the manufacturer"

As part of our commitment to you, all Hotpoint appliances have the added benefit of a fully inclusive parts

and labour guarantee for the first 12 months. In addition to this you also have the advantage of free

replacement parts for the first 5 years when fitted by a Hotpoint

engineer. When the 12 months parts and labour guarantee expires we offer the following after sales

service options:

Repair Service and Information Help Desk

UK: 08709 066066

www.theservicecentre.co.uk

Republic of Ireland: 1850 302 200

Note: Our operators will require the Model number and the Serial number of your appliance

Available 364 days a year with a fast, effective and value for money service. We have the largest white

goods repair service in the UK with over 1200 of our own fully trained engineers. All repairs include a

parts and labour guarantee for 12 months from the date of the repair.

If you require any information or have any questions about your appliance, our operators are on hand with

help and advice.

All this ensures that you will receive the best available after sales service possible.

Extended Warranties

UK: 08709 088 088

www.theservicecentre.co.uk

Republic of Ireland: 1850 502 200

Whether you have just one or a number of Hotpoint appliances in your kitchen, we offer two service cover

plans to give you total peace of mind.

l Repair Protection Plan - FREE service repairs for a single Hotpoint appliance during the period

of cover.

l Kitchen Cover - FREE service repairs for all your Hotpoint appliances less than 8

years old.

Genuine Parts and AccessoriesUK: 08709 077 077

www.theservicecentre.co.uk

Republic of Ireland: (01) 842 6836

A wide range of genuine parts and accessories are available from our hotline or through our web site.

Genuine parts and accessories, extended warranties and service repairs are all

available on our web-site at:

www.theservicecentre.co.uk

After Sales Service

Guarantee

"Satisfaction guaranteed or your money back"

We give you a unique 'satisfaction guaranteed' promise - valid for 90 days - after you have

purchased your Hotpoint appliance. If there is a technical problem simply call Hotpoint Repair service

or visit our web-site at www.theservicecentre.co.uk and where necessary, we will arrange for an

engineer to call. If the technical problem is not resolved under this guarantee, we will replace your

machine or, if you prefer, give you your money back.

All Hotpoint appliances carry a fully inclusive 12 month parts and labour guarantee as well as free

replacement parts for the first 5 years (except microwaves, selected integrated appliances and cooker

hoods, which have a one year guarantee) provided that they are fitted by a Hotpoint engineer.

Guarantee terms and conditions

Your guarantee is only applicable in the United Kingdom or Republic of Ireland and is subject to the

following provisions that your appliance:

l Has been installed and used correctly in accordance with this instruction booklet.

l Has been used solely for domestic purposes and is located on domestic premises (ie. not for

commercial or trade use).

l Has been properly connected to a suitable electrical supply voltage as stated on the appliance

rating plate.

l Has not been subject to misuse, accident, modified or repaired by anyone other than one of our

own service engineers.

For pre purchase information on any other Hotpoint product call: 08701 50 60 70

or visit: www.hotpoint.co.uk

Recycling & Disposal Information

As part of Hotpoint's continued commitment to helping the environment, Hotpoint reserves the right to

use quality recycled components to keep down customer costs and minimise material wastage.

Please dispose of packaging and old appliances carefully.

To minimise risk of injury to children, remove the door, plug and cut mains cable off flush with the

appliance. Dispose of these parts separately to ensure that the appliance can no longer be plugged

into a mains socket, and the door cannot be locked shut.

Key Contacts

After Sales Service

03/2005 - 195043663.01

Over 1200 trained specialists, directly employed by us, ensure that you can have complete confidence in

both the appliances and services we offer.

Repair Service and Information Desk

UK: 08709 066 066

(Open 8 to 8 Mon - Fri, 8 to 6 Sat, 10 to 4 Sun & Bank Holidays)

www.theservicecentre.co.uk

Republic of Ireland: 1850 302 200

Note: Our operators will require the following information:

Model number:

Serial number:

Extended Warranties

UK: 08709 088 088

(Open 8 to 8 Mon - Sun)

www.theservicecentre.co.uk

Republic of Ireland: 1850 502 200

Genuine Parts and Accessories

UK: 08709 077 077

(Open 8-30 to 5-30 Mon - Fri & 9 to 12 Sat)

www.theservicecentre.co.uk

Republic of Ireland: (01) 842 6836

Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB.

Hotpoint ET6004X Guida utente

Marca: Hotpoint

Modello: ET6004X

Categoria: Piani cottura

Tipo: Guida utente

Questo manuale è adatto anche per

ET7424 (T)

Scarica il pdf

rapporto

in altre lingue

English: Hotpoint ET6004X User guide

Hotpoint ET6004X Guida utente

Questo manuale è adatto anche per

Hotpoint ET6004X Guida utente

in altre lingue

Altri documenti