ESAB Arc 4000i Manuale utente

Categoria
Sistema di saldatura
Tipo
Manuale utente
Valid for serial no. 802--xxx--xxxx, 803--xxx--xxxx0458 636327 080105
Arc 4000i
Aristot /Origot
Instruction manual Èíñòðóêöèÿ ïî ýêñïëóàòàöèè
-- 2 --
Rights reserved to alter specifications without notice.
Îñòàâëÿåì çà ñîáîé ïðàâî èçìåíÿòü ñïåöèôèêàöèþ áåç ïðåäóïðåæäåíèÿ.
Ðóññêèé 3...............................................
ENGLISH 13..............................................
Ðóññêèé
TOCr
-- 3 --
1 ÒÅÕÍÈÊÀ ÁÅÇÎÏÀÑÍÎÑÒÈ 4........................................
2 ÂÂÅÄÅÍÈÅ 6.......................................................
2.1 Îáîðóäîâàíèå 6...........................................................
2.2 Ïàíåëè óïðàâëåíèÿ 6......................................................
3 ÒÅÕÍÈ×ÅÑÊÈÅ ÕÀÐÀÊÒÅÐÈÑÒÈÊÈ 7................................
ÑÒÀÍÎÂÊÀ 8.......................................................
4.1 Èíñòðóêöèè ïî ïîäúåìó 8..................................................
4.2 Ðàçìåùåíèå 8.............................................................
4.3 Ñåòü ýëåêòðîïèòàíèÿ 8.....................................................
5 ÏÎÐßÄÎÊ ÐÀÁÎÒÛ 9...............................................
5.1 Ñîåäèíåíèÿ è óñòðîéñòâà óïðàâëåíèÿ 9.....................................
5.2 Ïîäêëþ÷åíèå íàïðÿæåíèÿ ïèòàíèÿ 10........................................
5.3 Òàéìåð óïðàâëåíèÿ âåíò èëÿòîðàìè 10.......................................
5.4 Ðåëå çàùèòû îò òåïëîâîé ïåðåãðóçêè 10......................................
5.5 Ïóëüò äèñòàíöèîííîãî óïðàâëåíèÿ 10........................................
6 ÒÅÕÍÈ×ÅÑÊÎÅ ÎÁÑËÓÆÈÂÀÍÈÅ 11.................................
6.1 Î÷èñòêà âîçäóøíîãî ôèëüòðà 11.............................................
7 ÂÛßÂËÅÍÈÅ ÍÅÈÑÏÐÀÂÍÎÑÒÅÉ 12.................................
8 ÈÍÔÎÐÌÀÖÈß ÄËß ÇÀÊÀÇÀ ÇÀÏÀÑÍÛÕ ×ÀÑÒÅÉ 12.................
ÑÕÅÌÀ 22..............................................................
ÍÎÌÅÐ ÇÀÊÀÇÀ 24.....................................................
ÑÏÈÑÎÊ ÇÀÏÀÑÍÛÕ ×ÀÑÒÅÉ 25........................................
ÄÎÏÎËÍÈÒÅËÜÍÛÅ ÏÐÈÍÀÄËÅÆÍÎÑÒÈ 26...........................
bh23d1ra -- 4 --
1 ÒÅÕÍÈÊÀ ÁÅÇÎÏÀÑÍÎÑÒÈ
Ïîëüçîâàòåëè ñâàðî÷íîãî îáîðóäîâàíèÿ ESAB îòâå÷àþò çà âûïîëíåíèå ïðàâèë òåõíèêè
áåçîïàñíîñòè ëèöàìè, ðàáîòàþùèìè íà îáîðóäîâàíèè è ðÿäîì ñ íèì. Ïðàâèëà òåõíèêè
áåçîïàñíîñòè äîëæíû îòâå÷àòü òðåáîâàíèÿì ê áåçîïàñíîé ýêñïëóàòàöèè ñâàðî÷íîãî
îáîðóäîâàíèÿ ýòîãî òèïà. Ïîìèìî ñòàíäàðòíûõ ïðàâèë òåõíèêè áåçîïàñíîñòè è îõðàíû
òðóäà íà ðàáî÷åì ìåñòå ðåêîìåíäóåòñÿ ñëåäóþùåå.
Âñå ðàáîòû äîëæíû âûïîëíÿòüñÿ ïîäãîòîâëåííûìè ëèöàìè, çíàêîìûìè ñ ýêñïëóàòàöèåé
ñâàðî÷íîãî îáîðóäîâàíèÿ. Íåïðàâèëüíàÿ ýêñïëóàòàöèÿ îáîðóäîâàíèÿ ìîæåò âûçâàòü
îïàñíûì ñèòóàöèè, ïðèâîäÿùèå ê òðàâìèðîâàíèþ ïåðñîíàëà è ïîâðåæäåíèþ
îáîðóäîâàíèÿ.
1. Bñå ëèöà, èñïîëüçóþùèå ñ âàðî÷íîå îáîðóäîâàíèå, äîëæíû çíàòü:
S èíñòðóêöèè ïî ýêñïëóàòàöèè
S ðàñïîëîæåíèå îðãàíîâ àâàðèéíîãî îñòàíîâà
S íàçíà÷åíèå îáîðóäîâàíèÿ
S ïðàâèëà òåõíèêè áåçîïàñíîñòè
S òåõíîëîãèþ ñâàðêè
2. Îïåðàòîð îáåñïå÷èâàåò:
S óäàëåíèå ïîñòîðîííèõ ëèö èç ðàáî÷åé çîíû îáîðóäîâàíèÿ ïðè åãî çàïóñêå
S çàùèòó âñåõ ëèö îò âîçäåéñòâèÿ ñâàðî÷íîé äóãè
3. Ðàáî÷åå ìåñòî äîëæíî:
S îòâå÷àòü óñëîâèÿì ýêñïëóàòàöèè
S íå èìåòü ñêâîçíÿêîâ
4. Ñðåäñòâà çàùèòû ïåðñîíàëà
S Âî âñåõ ñëó÷àÿõ ðåêîìåíäóåòñÿ èñïîëüçîâàòü èíäèâèäóàëüíûå ñðåäñòâà çàùèòû,
íàïðèìåð, çàùèòíûå î÷êè, îãíåñòîéêóþ ñïåöîäåæäó è çàùèòíûå ðóêàâèöû.
S Ïðè ñâàðêå çàïðåùàåòñÿ íîñèòü ñâîáîäíóþ îäåæäó, óêðàøåíèÿ è ò.ä., íàïðèìåð,
øàðôû, áðàñëåòû, êîëüöà, êîòîðûå ìîãóò ïîïàñòü â ñâàðî÷íîå îáîðóäîâàíèå èëè
âûçâàòü îæîãè.
5. Îáùèå ìåðû ïðåäîñòîðîæíîñòè
S Ïðîâåðüòå íàäåæíîñòü ïîäêëþ÷åíèÿ îáðàòíîãî êàáåëÿ.
S Ðàáîòû íà îáîðóäîâàíèè ñ âûñîêèì íàïðÿæåíèåì äîëæíû ïðîèçâîäèòüñÿ òîëüêî
êâàëèôèöèðîâàííûì ýëåêòðèêîì.
S Â ïðåäåëàõ äîñòóïà äîëæíû íàõîäèòüñÿ ñîîòâåòñòâóþùèå ñðåäñòâà
ïîæàðîò óøåíèÿ, èìåþùèå ÿñíóþ ìàðêèðîâêó.
S Çàïðåùàåòñÿ ïðîâîäèòü ñìàçêó è òåõíè÷åñêîå îáñëóæèâàíèå îáîðóäîâàíèå âî
âðåìÿ ýêñïëóàòàöèè.
RU
bh23d1ra -- 5 --
Ïåðåä íà÷à ëîì ìîíòàæà è ýêñïëóàòàöèè âíèìàòåëüíî èçó÷èòå ñîîòâåòñòâóþùèå èíñòðóêöèè.
ÇÀÙÈÒÈÒÅ ÑÅÁß È ÄÐÓÃÈÕ!
ÂÍÈÌÀÍÈÅ!
Äóãoaaÿ caapka è peçka oïacíû kak äëa ècïoëíèteëÿ paáît, tak è äëa ïîctopoííèõëèö. Tpeáyéte
coáëþäåíèå àñåõ ïðààèë áåçîïàñíîñòè, äåéñòàóþùèõ íà îáúåêòå, êîòîðûå äîëæíû ó÷èòûààòú
ñåäåíèÿ îá îïàñíîñòÿõ, ïðåäñòààëåííûå èçãîãàèòåëåì ñààðî÷íîãî îáîðóäîààíèà.
ÎÏÀÑÍÎÑÒÜ ÑÌÅÐÒÅËÜÍÎÃÎ ÏÎÐÀÆÅÍÈß ÝËÅÊÒÐÈ×ÅÑÊÈÌ ÒÎÊÎÌ.
S Ñâàðî÷íûé àãðåãàò óñòàíàâëèâàåòñÿ è çàçåìëÿåòñÿ â ñîîòâåòñòâèè ñ äåéñòâóþùèìè íîðìàìè è
ïðàâèëàìè.
S Íå äîïóñêàéòå êîíòàêòà íàõîäÿùèõñÿ ïîä íàïðÿæåíèåì äåòàëåé è ýëåêòðîäîâ ñ íåçàùèùåííûìè
÷àñòÿìè òåëà, ìîêðûìè ðóêàâèöàìè è ìîêðîé îäåæäîé.
S Îáåñïå÷üòå ýëåêòðè÷åñêóþ èçîëÿöèþ îò çåìëè è ñâàðèâàåìûõ äå òàëåé.
S Îáåñïå÷üòå ñîáëþäåíèå áåçîïàñíûõ ðàáî÷èõ ðàññòîÿíèé.
ÄÛÌÛ È ÃÀÇÛ ìîãóò áûòü îïàñíû äëÿ ÷åëîâåêà
S Èñêëþ÷èòå âîçìîæíîñòü âîçäåéñòâèÿ äûìîâ.
S Äëÿ èñêëþ÷åíèÿ âäûõàíèÿ äûìîâ âî âðåìÿ ñâàðêè îðãàíèçóåòñÿ îáùàÿ âåíòèëÿöèÿ ïîìåùåíèÿ, à
òàêæåâûòÿæíàÿâåíòèëÿöèÿèççîíûñâàðêè.
ÈÇËÓ×ÅÍÈÅ ÄÓÃÈ âûçûâàåò ïîðàæåíèå ãëàç è îæîãè êîæè.
S Çàùèòèòå ãëàçà è êîæó. Äëÿ ýòîãî èñïîëüçóéòå çàùèòíûå ùèòêè, öâåòíûå ëèíçû è çàùèòíóþ
ñïåöîäåæäó.
S Äëÿ çàùèòû ï îñòîðîííèõ ëèö ïðèìåíÿþòñÿ çàùèòíûå ýêðàíû èëè çàíàâåñè.
ÏÎÆÀÐÎÎÏÀÑÍÎÑÒÜ
S Èñêðû (áðûçãè ìåòàëëà) ìîãóò âûçâàòü ïîæàð. Óáåäèòåñü â îòñóòñòâèè ãîðþ÷èõ ìàòåðèàëîâ
ïîáëèçîñòè îò ìåñòà ñâàðêè.
ØÓÌ - ×ðåçìåðíûé øóì ìîæåò ïðèâåñòè ê ïîâðåæäåíèþ îðãàíîâ ñëóõà
S Ïðèìèòå ìåðû äëÿ çàùèòû ñëóõà. Èñïîëüçóéòå çàòû÷êè äëÿ óøåé èëè äðóãèå ñðåäñòâà çàùèòû
ñëóõà.
S Ïðåäóïðåäèòå ïîñòîðîííèõ ëèö îá îïàñíîñòè.
ÍÅÈÑÏÐÀÂÍÎÑÒÈ -- Ïðè íåèñïðàâíîñòè îáðàòèòåñü ê ñïåöèàëèñòàì ïî ñâàðî÷íîìó
îáîðóäîâàíèþ
ÂÍÈÌÀÍÈÅ!
Çàïðåùàåòñÿ èñïîëüçîâàòü èñòî÷íèê ïèòàíèÿ äëÿ îòòàèâàíèÿ òðóá.
ÎÑÒÎÐÎÆÍÎ!
Ïåðåä íà÷àëîì ìîíòàæà è ýêñïëóàòàöèè
âíèìàòåëüíî èçó÷èòå ñîîòâåòñòâóþùèå
èíñòðóêöèè.
Âíèìàíèå!
Ýòî óñòðîéñòâî ïðåäíàçíà÷åíî èñêëþ÷èòåëüíî äëÿ ýëåêòðîäóãîâîé ñâàðêè!
Êîìïàíèÿ ESAB ãîòîâà ïðåäîñòàâèòü âàì âñå çàùèòíîå ñíàðÿæåíèå è
ïðèíàäëåæíîñòè, íåîáõîäèìûå äëÿ âûïîëíåíèÿ ñâàðî÷íûõ ðàáîò.
RU
bh23d1ra -- 6 --
2 ÂÂÅÄÅÍÈÅ
Áëîê Arc 4000i ïðåäñòàâëÿåò ñîáîé ñâàðî÷íûé èñòî÷íèê ïèòàíèÿ,
ïðåäíàçíà÷åííûé äëÿ ñâàðêè ïîêðûòûì ýëåêòðîäîì (MMA).
Îí ïîñòàâëÿåòñÿ â äâóõ âàðèàíòàõ:
S Arc 4000i ñ ïàíåëüþ óïðàâëåíèÿ A2
S Arc 4000i ñ ïàíåëüþ óïðàâëåíèÿ A4.
Àêñåññóàð² îò äëÿ èçäåëÿ ìîæíî íàéòè íà ñòðíèöå 26.
2.1 Îáîðóäîâàíèå
 êîìïëåêòå ñ áëîêîì Arc 4000i ïîñòàâëÿþòñÿ èíñòðóêöèè íà èñòî÷íèê ïèòàíèÿ
è îäíà èíñòðóêöèÿ íà ïàíåëü óïðàâëåíèÿ.
2.2 Ïàíåëè óïðàâëåíèÿ
Èñòî÷íèê ïèòàíèÿ ïîñòàâëÿåòñÿ â êîìïëåêòå ñ îäíîé èç ñëåäóþùèõ ïàíåëåé
óïðàâëåíèÿ:
S A2
Ñ ðó÷êàìè äëÿ ðåãóëèðîâêè âñåõ ïàðàìåòðîâ.
S A4
Ñ ðó÷êîé äëÿ ðåãóëèðîâêè ñâàðî÷íîãî òîêà. Äðóãèå ïàðàìåòðû
ðåãóëèðóþòñÿ ñ ïîìîùüþ êíîïîê ñ èíäèêàöèåé ñèìâîëîâ íà ïàíåëè
äèñïëåÿ.
Ïîäðîáíûå ñâåäåíèÿ î ïàíåëÿõ óïðàâëåíèÿ ïðèâåäåíû â îòäåëüíûõ
èíñòðóêöèÿõ.
RU
bh23d1ra -- 7 --
3 ÒÅÕÍÈ×ÅÑÊÈÅ ÕÀÐÀÊÒÅÐÈÑÒÈÊÈ
Arc 4000i
Íàïðÿæåíèå ñåòè ïèòàíèÿ 400 Â, 10%, 3 50 Ãö
Ïèòàíèå îò ñåòè S
sc min
2,0 MVA
Ïåðâè÷íûé òîê I
ìàêñ.
27 A
Ïîòðåáëÿåìàÿ ìîùíîñòü õîëîñòîãî õîäà âðåæèìå
ýíåðãîñáåðåæåíèÿ, 6,5 ìèí ïîñëå ñâàðêè
50 Âò
Äèàïàçîí óñòàâîê 16 A - 400 A
Ìàêñèìàëüíàÿ äîïóñòèìàÿ íàãðóçêà ïðè
êîýôôèöèåíò íàãðóçêè 35%
êîýôôèöèåíò íàãðóçêè 60%
êîýôôèöèåíò íàãðóçêè 100%
400 A / 36 Â
320 A / 33 Â
250 A / 30 Â
Êî ýôôèöèåíò ìîùíîñòè ïðè ìàêñèìàëüíîì òîêå 0,90
Êïä ïðè ìàêñèìàëüíîì òîêå 86%
Íàïðÿæåíèå õîëîñòîãî õîäà 78 - 90 Â
Äèàïàçîí òåìïåðàòóð îò -10 äî + 40˚C
Ãàáàðèòû,ÄxØx 625 x 294 x 492 ìì
Íåïðåðûâíî äåéñòâóþùåå ñðåäíåå âçâåøåííîå
çâóêîâîå äàâëåíèå
<70 äÁ
Ìàññà 47,5 êã
Êëàññ èçîëÿöèè H
Êëàññ çàùèòû êîðïóñà IP 23
Êëàññ ïðèìåíåíèÿ
Ðàáî÷èé öèêë
Ðàáî÷èé öèêë ïðåäñòàâëÿåò ñîáîé äîëþ %%) äåñÿòèìèíóòíîãî èíòåðâàëà, â òå÷åíèå
êîòîðîé ìîæíî ïðîèçâîäèòü ñâàðêó ïðè îïðåäåëåííîé íàãðóçêå áåç ïåðåãðóçêè.
Ðàáî÷èéöèêëóêàçàíäëÿòåìïåðàòóðû40˚C.
Êëàññ êîæóõà
Íîðìû IP óêàçûâàþò êëàññ êîæóõà, ò.å., ñòåïåíü çàùèòû îò ïðîíèêíîâåíèÿ òâåðäûõ
îáúåêòîâ è âîäû. Îáîðóäîâàíèå ñ ìàðêèðîâêîé IP 23 ïðåäíàçíà÷åíî äëÿ íàðóæíîé è
âíóòðåííåé óñòàíîâêè.
Ê ëàññ çîíû óñòàíîâêè
Ýòîò ñèìâîë îçíà÷àåò, ÷òî èñòî÷íèê ïèòàíèÿ ïðåäíàçíà÷åí äëÿ èñïîëüçîâàíèÿ â çîíàõ ñ
ïîâûøåííîé îïàñíîñòüþ ïîðàæåíèÿ ýëåêòðîòîêîì.
Ïèòàíèå îò ñåòè, S
sc ìèí.
Ìíèìàëüíàÿ ìîùíîñòü ïðè êîðîòêîì çàìûêàíèè ñåòè â ñîîòâåòñòâèè ñî ñòàíäàðòîì IEC
61000-3-12
RU
bh23d1ra -- 8 --
ÑÒÀÍÎÂÊÀ
Ââîä â ýêñïëóàòàöèþ äîëæåí ïðîèçâîäèòüñÿ êâàëèôèöèðîâàííûì
ñïåöèàëèñòîì.
Ïðèìe÷aíèå!
Òðåáîâàíèÿ ê ñåòÿì ýëåêòðîñíàáæåíèÿ
Èç-çà áîëüøèõ âåëè÷èí òîêà â ïåðâè÷íîé îáìîòêå îáîðóäîâàíèå âûñîêîé ìîùíîñòè ìîæåò
ñóùåñòâåííî ïîâëèÿòü íà ìîùíîñòíûå õàðàêòåðèñòèêè ñåòè. Ïîýòîìó â îòíîøåíèè
íåêîòîðîãî îáîðóäîâàíèÿ ïðèìåíÿþòñÿ îãðàíè÷åíèÿ èëè äîïîëíèòåëüíûå òðåáîâàíèÿ,
êàñàþùèåñÿ ìàêñèìàëüíî äîïóñòèìîãî ñîïðîòèâëåíèÿ îáîðóäîâàíèÿ èëè ìèíèìàëüíîé
ñïîñîáíîñòè îáåñïå÷èòü ñòàáèëüíîå ýíåðãîñíàáæåíèå â òî÷êàõ âçàèìîäåéñòâèÿ
îáùåñòâåííûõ ñåòåé.  òàêîì ñëó÷àå ïîëüçîâàòåëü îáîðóäîâàíèÿ èëè òîò, êòî åãî
óñòàíàâëèâàåò, äîëæåí ïðîêîíñóëüòèðîâàòüñÿ ñ îïåðàòîðîì ýíåðãîñåòè ïî ïîâîäó
âîçìîæíîñòè ïîäêëþ÷åíèÿ òàêîãî ðîäà îáîðóäîâàíèÿ.
4.1 Èíñòðóêöèè ïî ïîäúåìó
4.2 Ðàçìåùåíèå
Ðàçìåñòèòå ñâàðî÷íûé èñòî÷íèê ïèòàíèÿ òàêèì îáðàçîì, ÷òîáû åãî
âîçäóõîçàáîðíûå è âûïóñêíûå îòâåðñòèÿ íå áûëè çàãðàæäåíû.
4.3 Ñåòü ýëåêòðîïèòàíèÿ
Óáåäèòåñü â òîì, ÷òî áëîê ïîäêëþ÷åí ê ñåòè ýëåêòðîïèòàíèÿ ñ òðåáóåìûì
íàïðÿæåíèåì è çàùèùåí ïðåäîõðàíèòåëÿìè òðåáóåìîãî íîìèíàëà.
Âûïîëíèòå âñå çàùèòíûå çàçåìëåíèÿ ñîãëàñíî òðåáîâàíèÿì
ñîîòâåòñòâóþùèõ íîðì.
Ïàñïîðòíàÿ òàáëè÷êà ñ ïàðàìåòðàìè ñåòè ýëåêòðîïèòàíèÿ.
RU
bh23d1ra -- 9 --
Ðåêîìåíäóåìûé íîìèíàë ïðåäîõðàíèòåëÿ è ìèíèìàëüíàÿ äëèíà êàáåëÿ
Arc 4000i 400 Â, 3~50 Ãö
Íàïðÿæåíèå ñåòè ïèòàíèÿ 400 Â
Ïëîùàäü ïîïåðå÷íîãî ñå÷åíèÿ
ñèëîâîãî êàáåëÿ ïèòàíèÿ, ìì
2
4G4
Ôàçíûé òîê, I ýôô. 16 A
Ïðåäîõðàíèòåëü
Óñòîé÷èâûé ê ïåðåíàïðÿæåíèÿì
Òèï C, MCB
20 A
20 A
Âíèìàíèå!
Äëèíà êàáåëÿ è íîìèíàë ïðåäîõðàíèòåëÿ ñîîòâåòñòâóþò øâåäñêèì íîðìàì äëÿ
ýëåêòðîóñòàíîâîê. Âûïîëíèòå ïîäñîåäèíåíèå ê ñåòè ïèòàíèÿ â ñîîòâåòñòâèè ñ ìåñòíûìè
íîðìàìè.
5 ÏÎÐßÄÎÊ ÐÀÁÎÒÛ
Îáùèå ïðàâèëà òåõíèêè áåçîïàñíîñòè ïðè ðàáîòå ñ îáîðóäîâàíèåì
ïðèâîäÿòñÿ íà ñòð. 4. Ïðî÷òèòå èõ äî èñïîëüçîâàíèÿ îáîðóäîâàíèÿ!
5.1 Ñîåäèíåíèÿ è óñòðîéñòâà óïðàâëåíèÿ
1
Ñîåäèíèòåëü êàáåëÿ ñâàðî÷íîãî òîêà
(+)
5
Áåëàÿ èíäèêàòîðíàÿ ëàìïà - Èñòî÷íèê
ïèòàíèÿ ÂÊË. (ON)
2
Ñîåäèíèòåëü ïóëüòà äèñòàíöèîííîãî
óïðàâëåíèÿ
6
Îðàíæåâàÿ èíäèêàòîðíàÿ ëàìïà -
Ïåðåãðåâ
3
Ñîåäèíèòåëü îáðàòíîãî êàáåëÿ
ñâàðî÷íîãî òîêà (-)
7
Ïàíåëü óïðàâëåíèÿ
(ñì. ñîîòâåòñòâóþùåå Ðóêîâîäñòâî ïî
ýêñïëóàòàöèè)
4
Ñåòåâîé âûêëþ÷àòåëü, 0 / 1 / ÏÓÑÊ
RU
bh23d1ra -- 1 0 --
5.2 Ïîäêëþ÷åíèå íàïðÿæåíèÿ ïèòàíèÿ
Âêëþ÷èòå ïèòàíèå, ïîâåðíóâ ïîäïðóæèíåííûé âûêëþ÷àòåëü (4) â ïîëîæåíèå
“START” (ÏÓÑÊ). Âûêëþ÷àòåëü âîçâðàùàåòñÿ â ïîëîæåíèå “1”, áóäó÷è
îòïóùåí.
Åñëè íàïðÿæåíèå â ñåòè ïèòàíèÿ ïðîïàäåò, à çàòåì âíîâü âîññòàíîâèòñÿ, òî
èñòî÷íèê ïèòàíèÿ îñòàíåòñÿ â îòêëþ÷åííîì ñîñòîÿíèè, ïîêà âûêëþ÷àòåëü íå
áóäåò ñíîâà ïîâåðíóò â ïîëîæåíèå “START (ÏÓÑÊ)” è çàòåì îòïóùåí.
×òîáû âûêëþ÷èòü èñòî÷íèê ïèòàíèÿ, ïîâåðíèòå âûêëþ÷àòåëü â ïîëîæåíèå “0”.
Åñëè èñòî÷íèê ïèòàíèÿ îòêëþ÷èòñÿ â ðåçóëüòàòå ñáîÿ ïî ïèòàíèþ èëè
îáû÷íîãî âûêëþ÷åíèÿ âðó÷íóþ, òî ïàðàìåòðû ñâàðêè áóäóò ñîõðàíåíû, òàê
÷òî èõ ìîæíî áóäåò èñïîëüçîâàòü ïðè ñëåäóþùåì âêëþ÷åíèè áëîêà.
5.3 Òàéìåð óïðàâëåíèÿ âåíòèëÿòîðàìè
Âåíòèëÿòîðû èñòî÷íèêà ïèòàíèÿ ïðîäîëæàþò ðàáîòàòü â òå÷åíèå 6,5 ìèí
ïîñëå ïðåêðàùåíèÿ ñâàðêè, à ñàì áëîê ïåðåêëþ÷àåòñÿ â ðåæèì
ýíåðãîñáåðåæåíèÿ. Ïðè âîçîáíîâëåíèè ñâàðêè âåíòèëÿòîðû âíîâü íà÷íóò
ðàáîòàòü.
Âåíòèëÿòîðû ðàáîòàþò íà ïîíèæåííûõ îáîðîòàõ ïðè ñâàðî÷íûõ òîêàõ äî 144 A
è íà ïîëíûõ îáîðîòàõ ïðè áîëüøèõ òîêàõ.
5.4 Ðåëå çàùèòû îò òåïëîâîé ïåðåãðóçêè
Èñòî÷íèê ïèòàíèÿ èìååò äâà ðåëå çàùèòû îò òåïëîâîé ïåðåãðóçêè, êîòîðûå
ñðàáàòûâàþò ïðè íåäîïóñòèìîì âîçðàñòàíèè âíóòðåííåé òåìïåðàòóðû. Ïðè
ýòîì ïðåêðàùàåòñÿ ïîäà÷à ñâàðî÷íîãî òîêà è çàãîðàåòñÿ îðàíæåâàÿ
èíäèêàòîðíàÿ ëàìïà íà ëèöåâîé ïàíåëè áëîêà. Êîãäà òåìïåðàòóðà ñíèçèòñÿ,
ðåëå âíîâü àâòîìàòè÷åñêè âêëþ÷àòñÿ.
5.5 Ïóëüò äèñòàíöèîííîãî óïðàâëåíèÿ
Äëÿ íàäëåæàùåãî ôóíêöèîíèðîâàíèÿ äèñòàíöèîííîãî óïðàâëåíèÿ íà
ìàøèíàõ Aristo ñî âñòðîåííûìè ïàíåëÿìè óïðàâëåíèÿ äîëæíà áûòü
óñòàíîâëåíà âåðñèÿ ïðîãðàììíîãî îáåñïå÷åíèÿ 1.21 èëè âûøå.
Åñëè ïóëüòà äèñòàíöèîííîãî óïðàâëåíèÿ, èñòî÷íèê ïèòàíèÿ íàõîäèòñÿ â
ðåæèìå äèñòàíöèîííîãî óïðàâëåíèÿ, è âñå êíîïêè è ðó÷êè óïðàâëåíèÿ
çàáëîêèðîâàíû. Ðåãóëèðîâêó âñåõ ôóíêöèé ìîæíî âûïîëíèòü òîëüêî ïðè
ïîìîùè ïóëüòà äèñòàíöèîííîãî óïðàâëåíèÿ.
Åñëè ïóëüò äèñòàíöèîííîãî óïðàâëåíèÿ íå èñïîëüçóåòñÿ, åãî âìåñòå ñ
àäàïòåðîì ñëåäóåò îòñîåäèíèòü îò èñòî÷íèêà ïèòàíèÿ, êîòîðûé â ïðîòèâíîì
ñëó÷àå áóäåò ïðîäîëæàòü ðàáîòàòü â ðåæèìå äèñòàíöèîííîãî óïðàâëåíèÿ.
Ïîäðîáíûå ñâåäåíèÿ î ðàáîòå ïóëüòà äèñòàíöèîííîãî óïðàâëåíèÿ ïðèâåäåíû
â èíñòðóêöèÿõ ïî ýêñïëóàòàöèè ïàíåëè óïðàâëåíèÿ.
RU
bh23d1ra -- 1 1 --
6 ÒÅÕÍÈ×ÅÑÊÎÅ ÎÁÑËÓÆÈÂÀÍÈÅ
Ïðèìå÷àíèå:
à àðàíòìèéíûå îáÿçàòåëüñòâà ïîñòàâùèêà òåðÿþò ñèëó, åñëè ïîêóïàòåëú
ñàìîñòîÿòåëúíî ïûòàåòñÿ ïðîèçâåñòè êàêèå-ëèáî ðàáîòû ïî óñòðàíåíèþ
íåèñïðàâíîñòåé èçäåëèÿ â òå÷åíèå ãàðàíòèéíîãî ñðîêà.
Ðåã óëÿðíîå òåõíè÷åñêîå îáñëóæèâàíèå èìååò âàæíîå çíà÷åíèå äëÿ
îáåñïå÷åíèÿ áåçîïàñíîñòè è íàäåæíîñòè.
Ïîäê ëþ÷åíèå, îáñëóæèâàíèå è ðåìîíò ñâàðî÷íîãî îáîðóäîâàíèå, ñâÿçàííûå
ñî ñíÿòèåì çàùèòíûõ ùèòêîâ, âûïîëíÿþòñÿ ëèöàìè, ïðîøåäøèìè
ñîîòâåòñòâóþùóþ ýëåêòðîòåõíè÷åñêóþ ïîäãîòîâêó è àòòåñòîâàííûìè íà ïðàâî
âûïîëíåíèÿ òàêèõ ðàáîò.
6.1 Î÷èñòêà âîçäóøíîãî
ôèëüòðà
S Ðàçáëîêèðóéòå âåðõíþþ êðûøêó ñ
ïûëåóëàâëèâàþùèì ôèëüòðîì (1).
S Îòêèíüòå âåðõíþþ êðûøêó (2).
S Èçâëåêèòå ïûëåóëàâëèâàþùèé
ôèëüòð (3).
S Ïðîäóéòå åãî íà÷èñòî ñæàòûì
âîçäóõîì íèçêîãî äàâëåíèÿ.
S Óñòàíîâèòå ôèëüòð íà ìåñòî,
ïîâåðíóâ åãî ñåòêîé ñ áîëåå ìåëêèìè
ÿ÷åéêàìè ê âåðõíåé êðûøêå (2).
S Çàêðîéòå âåðõíþþ êðûøêó âìåñòå ñ ôèëüòðîì.
RU
bh23d1ra -- 1 2 --
7 ÂÛßÂËÅÍÈÅ ÍÅÈÑÏÐÀÂÍÎÑÒÅÉ
Ïðåæäå ÷åì âûçûâàòü àòòåñòîâàííîãî ñïåöèàëèñòà ïî îáñëóæèâàíèþ,
ïîïðîáóéòå ñàìîñòîÿòåëüíî âûïîëíèòü ðåêîìåíäóåìûå íèæå ïðîâåðêè.
Òèï íåèñïðàâíîñòè Äåéñòâèÿ
Îòñóòñòâèå äóãè S Ïðîâåðüòå, âêëþ÷åí ëè âûêëþ÷àòåëü ïèòàíèÿ.
S Ïðîâåðüòå ïðàâèëüíîñòü ïîäñîåäèíåíèÿ êàáåëåé ïîäà÷è
ñâàðî÷íîãî òîêà è îáðàòíûõ êàáåëåé.
S Ïðîâåðüòå, ïðàâèëüíî ëè çàäàíà âåëè÷èíà òîêà.
Ïðåðûâàíèå ñâàðî÷íîãî òîêà
âî âðåìÿ ñâàðêè
S Ïðîâåðüòå, íå ñðàáîòàëè ëè ðåëå çàùèòû îò òåïëîâîé
ïåðåãðóçêè (ñðàáàòûâàíèå ðåëå îïðåäåëÿåòñÿ ïî
çàãîðàíèþ îðàíæåâîé ëàìïû íà ëèöåâîé ïàíåëè).
S Ïðîâåðüòå ñåòåâûå ïðåäîõðàíèòåëè.
×àñòî ñðàáàòûâàþò ðåëå
çàùèòû îò òåïëîâîé
ïåðåãðóçêè.
S Ïðîâåðüòå, íå çàñîðåíû ëè âîçäóøíûå ôèëüòðû.
S Óáåäèòåñü â òîì, ÷òî íå ïðåâûøåíû íîìèíàëüíûå
çíà÷åíèÿ ïàðàìåòðîâ èñòî÷íèêà ïèòàíèÿ (ò. å. ÷òî
óñòðîéñòâî ðàáîòàåò áåç ïåðåãðóçêè).
Íèçêàÿ ýôôåêòèâíîñòü
ñâàðêè.
S Ïðîâåðüòå ïðàâèëüíîñòü ïîäñîåäèíåíèÿ êàáåëåé ïîäà÷è
ñâàðî÷íîãî òîêà è îáðàòíûõ êàáåëåé.
S Ïðîâåðüòå, ïðàâèëüíî ëè çàäàíà âåëè÷èíà òîêà.
S Óáåäèòåñü â òîì, ÷òî èñïîëüçóþòñÿ ýëåêòðîäû
òðåáóåìîãî òèïà.
S Ïðîâåðüòå ñåòåâûå ïðåäîõðàíèòåëè.
8 ÈÍÔÎÐÌÀÖÈß ÄËß ÇÀÊÀÇÀ ÇÀÏÀÑÍÛÕ ×ÀÑÒÅÉ
Ðàáîòû ïî ðåìîíòó è ýëåêòðè÷åñêîìó ìîíòàæó äîëæíû âûïîëíÿòüñÿ
êâàëèôèöèðîâàííûì ñïåöèàëèñòîì ESAB .
Íåîáõîäèìî èñïîëüçîâàòü òîëüêî çàïàñíûå ÷àñòè, âûïóùåííûå ôèðìîé
ESAB.
Çàïàñíûå ÷àñòè ìîæíî çàêàçòú ó áëèæàéøåãî ê Âàì ESAB, (ñì. ïåðå÷åíú íà
ïîñëåäíåé ñòðàíèöå äàííîé áðîøþðû).
RU
ENGLISH
-- 1 3 --
TOCe
1 DIRECTIVE 14........................................................
2SAFETY 14...........................................................
3 INTRODUCTION 16...................................................
3.1 Equipment 16................................................................
3.2 Control panels 16............................................................
4 TECHNICAL DATA 17.................................................
5 INSTALLATION 17....................................................
5.1 Lifting instructions 18.........................................................
5.2 Placing 18...................................................................
5.3 Mains power supply 18........................................................
6 OPERATION 19.......................................................
6.1 Connections and control devices 19............................................
6.2 Main voltage connection 19....................................................
6.3 Fan control timer 19..........................................................
6.4 Thermal overload protection 20................................................
6.5 Remote control unit 20........................................................
7 MAINTENANCE 20....................................................
7.1 Cleaning the air filter 20.......................................................
8 FAULT TRACING 21...................................................
9 ORDERING SPARE PARTS 21..........................................
DIAGRAM 22............................................................
ORDERING NUMBER 24.................................................
SPARE PARTS LIST 25...................................................
ACCESSORIES 26.......................................................
-- 1 4 --
bh23d1ea
1 DIRECTIVE
DECLARATION OF CONFORMITY
ESAB AB, Welding Equipment, SE--695 81 Laxå, Sweden, gives its unreserved guarantee that weld-
ing power source Arc 4000i from serial number 802 (2008 w.02) are constructed and tested in comp-
liance with the standard EN 60974--1 and EN 60974--10 (Class A) in accordance with the require-
ments of directive (2006/95/EC) and (2004/108/EEC).
-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --------
Kent Eimbrodt
Global Director
Equipment and Automation
Laxå 2008--01--04
2SAFETY
Users of ESAB welding equipment have the ultima te responsibility for ensuring that anyone who
works on or near the equipment observes all the relevant safety precautions. Safety precautions
must meet the requirements that apply to this type of welding equipment. The following recommen-
dations should be observed in addition to the standard regulations that apply to the workplace.
All work must be carried out by trained personnel well--acquainted with the operation of the welding
equipment. Incorrect operation of the equipment may lead to hazardous situations which can result
in injury to the operator and damage to the equipment.
1. Anyone who uses the welding equipment must be familiar with:
S its operation
S location of emergency stops
S its function
S relevant safety precautions
S welding
2. The operator must ensure that:
S no unauthorized person is stationed within the working area of the equipment when it is
started up.
S no--one is unprotected when the arc is struck
3. The workplace must:
S be suitable for the purpose
S be free from drafts
4. Personal safety equipment
S Always wear recommended personal safety equipment, such as safety glasses, flame--proof
clothing, safety gloves.
S Do not wear loose--fitting items, such as scarves, bracelets, rings, etc., which could become
trapped or cause burns.
5. General precautions
S Make sure the return cable is connected securely.
S Work on high voltage equipment may only be carried out by a qualified electrician.
S Appropriate fire extinquishing equipment must be clearly marked and close at hand.
S Lubrication and maintenance must not be carried out on the equipment during operation.
GB
-- 1 5 --
bh23d1ea
WARNING
Read and understand the instruction manual before installing or operating.
Arc welding and cutting can be injurious to yourself and others. Take precausions when welding.
Ask for your employer’s safety practices which should be based on manufacturers’ hazard data.
ELECTRIC SHOCK - Can kill
S Install and earth the welding unit in accordance with applicable standards.
S Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.
S Insulate yourself from earth and the workpiece.
S Ensure your working stance is safe.
FUMES AND GASES - Can be dangerous to health
S Keep your head out of the fumes.
S Use ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone
and the general area.
ARC RAYS - Can injure eyes and burn skin.
S Protect your eyes and body. Use the correct welding screen and filter lens and wear protective
clothing.
S Protect bystanders with suitable screens or curtains.
FIRE HAZARD
S Sparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.
NOISE - Excessive noise can damage hearing
S Protect your ears. Use earmuffs or other hearing protection.
S Warn bystanders of the risk.
MALFUNCTION - Call for expert assistance in the event of malfunction.
PROTECT YOURSELF AND OTHERS!
CAUTION!
Read and understand the instruction manual before
installing or operating.
WARNING!
Do not use the power source for thawing frozen pipes.
CAUTION!
This product is solely intended for arc welding.
CAUTION!
Class A equipment is not intended for use in residential locations where
the electrical power is provided by the public low--voltage supply system.
There may be potential difficulties in ensuring electromagnic
compatibility of class A equipment in those locations, due to conducted
as well as radiated disturbances.
GB
-- 1 6 --
bh23d1ea
Do not dispose of electrical equipment together with normal waste!
In observance of European Directive 2002/96/EC on Waste Electrical and Electronic
Equipment and its implementation in accordance with national law, electrical equipment
that has reached the end of its life must be collected separately and returned to an
environmentally compatible recycling facility. As the owner of the equipment, you should
get information on approved collection systems from our local representative.
By applying this European Directive you will improve the environment and human
health!
ESAB can provide you with all necessary welding protection and accessories.
3 INTRODUCTION
The Arc 4000i is a welding current power source intended for use with coated
electrodes (MMA welding).
It is available in two variants:
S Arc 4000i with the A2 control panel
S Arc 4000i with the A4 control panel.
See page 26 for details of ESAB’s accessories for the power unit.
3.1 Equipment
The Arc 4000i is supplied with instruction manuals for power source and for the
control panel.
3.2 Control panels
The power source is supplied with one of the following control panels:
S A2
With knobs for all control settings.
S A4
With a knob for setting the welding current. Other functions controlled by
pushbuttons and symbols in the display panel.
See the separate instruction manuals for detailed descriptions of the control panels.
GB
-- 1 7 --
bh23d1ea
4 TECHNICAL DATA
Arc 4000i
Mains voltage 400 V, ±10%, 3 50 Hz
Mains supply S
sc min
2.0 MVA
Primary current I
max
27 A
No--load power in energy--saving mode 6.5 min. after welding 50 W
Setting range 16 A -- 400 A
Maximum permissible load at
35% duty cycle
60 % duty cycle
100 % duty cycle
400 A / 36 V
320 A / 33 V
250 A / 30 V
Power factor at maximum current 0,90
Efficiency at maximum current 86%
Open--circuit voltage 78 -- 90 V
Temperature range
--10 till + 40˚C
Dimensions, l x b x h 625 x 294 x 492 mm
Continual A--weighted sound pressure <70 db
Weight 47,5 kg
Insulation class H
Enclosure class IP 23
Application class
Duty cycle
The duty cycle r efers to the time as a percentage of a ten--minute period that you can weld at a cer-
tain load without overloading.
The duty cycle is valid for 40˚C.
Enclosure class
The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid
objects or water. Equipment marked IP23 is designed for indoor and outdoor use.
Application class
The symbol indicates that the power source is designed for use in areas with increased
electrical hazard.
Mains supply, S
sc min
Minimum short circuit power on the network in accordance with IEC 61000--3--12
5 INSTALLATION
The installation must be executed by a professional.
Note!
Mains supply requirements
High power equipment may, due to the primary current drawn from the mains supply, influence the
power quality of the grid. Therefore connection restrictions or requirements r egarding the maximum
permissible mains impedance or the required minimum supply capacity at the interface point to the
public grid may apply for some types of equipment (see technical data). In this case it is the
responsibility of the installer or user of the equipment to ensure, by consultation with the
distrubution network operator if necessary, that the equipment may be connected.
GB
-- 1 8 --
bh23d1ea
5.1 Lifting instructions
5.2 Placing
Place the power source so that its cooling air inlets and outlets are not obstructed.
5.3 Mains power supply
Make sure that the unit is connected to the correct supply voltage, and that it is
protected by the correct fuse rating. Make protective earth connections in
accordance with the requirements of applicable regulations.
Rating plate with supply data.
Recommended fuse rating and minimum cable size
Arc 4000i 400 V, 3~50 Hz
Supply voltage 400 V
Mains cable size, mm
2
4G4
Phase current, I
1eff
16 A
Fuse
anti--surge
Type C, MCB
20 A
20 A
Note!
Cable size and fuse ratingcomplies to Swedish electrical regulations. C onnect the power supply in
conformance with local regulations.
GB
-- 1 9 --
bh23d1ea
6 OPERATION
General safety regulations for the handling of the equipment can be found on
page 14. Read through before you start using the equipment!
6.1 Connections and control devices
1 Welding current cable connector (+) 5 White indicating lamp, mains power supply
ON
2 Connector for remote control 6 Orange indicating lamp, overheating
3 Return welding current cable connector
(--)
7 Control panel (see respective instruction
manual)
4 Main power supply switch, 0 / 1 /
START
6.2 Main v oltage connection
Turn on the power supply by turning switch (4) against the spring to the “START”
position. The switch returns to the “1” position when it is released.
If the mains power supply is interrupted, and then restored, the power source
remains off until the switch is again turned to the “START” position and released.
Turn the power off by turning the switch to the “0” position.
Whether in the event of a loss of power supply or of turning the power source off in
the normal manner, welding data will be stored so that it is available next time the
unit is started.
6.3 Fan control timer
The power source fans continue to run for 6,5 minutes after welding has stopped,
and the unit switches to energy--saving mode. They start again when welding
restarts.
The fans run at reduced speed for welding currents up to 144 A, and at full speed for
higher currents.
GB
-- 2 0 --
bh23d1ea
6.4 Thermal overload protection
The power source has two thermal overload trips which operate if the internal
temperature becomes too high, interrupting the welding current and lighting the
orange indicating lamp on the front of the unit. The trips reset automatically when
the temperature has fallen.
6.5 Remote control unit
Aristo machines with intergral control panels should have program version 1.21 or
higher, in order for the remote control to function correctly.
When the remote control unit is connected, the power source is in remote control
mode; the buttons and knobs are blocked. The functions can only be adjusted via the
remote control unit.
If the remote control unit is not to be used, the remote control unit m ust be
disconnected from the power source as otherwise it will remain in remote control
mode.
For more information about the operation of the remote control unit, see the relevant
operating instructions for the control panel.
7 MAINTENANCE
Note!
All guarantee undertakings from the supplier cease to apply if the customer himself
attempts any work in the product during the guarantee period in order to rectify any
faults.
Regular maintenance is important for safe, reliable operation.
Only those persons who have appropriate electrical knowledge (authorized
personnel) may remove the safety plates to connect or carry out service,
maintenance or repair work on welding equipment.
7.1 Cleaning the air filter
S Release the cover plate with the dust
filter (1).
S Swing out the cover plate (2).
S Remove the dust filter (3).
S Blow it clean with compressed air at
reduced pressure.
S Replace the filter with the finer mesh on
the side against the cover plate (2).
S Replace the cover plate with the filter.
GB
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

ESAB Arc 4000i Manuale utente

Categoria
Sistema di saldatura
Tipo
Manuale utente

in altre lingue