Yamaha NHB32 Manuale utente

Marca: Yamaha

Modello: NHB32

Categoria: Switch di rete

Tipo: Manuale utente

Questo manuale è adatto anche per

ENGLISHFRANÇAISDEUTSCHESPAÑOL

AMP CONTROL UNIT

NETWORK HUB and BRIDGE

Owner’s Manual

Mode d’emploi

Bedienungsanleitung

Manual de instrucciones

NETWORK HUB AND BRIDGE

LINK CONDUCT

LOCK

ERROR

– 2 –

ACU16-C/NHB32-C

Owner’s Manual Addendum

Please make the following changes and additions to the ACU16-C/NHB32-C owner’s manual. Some of

these are due to the ACU16-C/NHB32-C system software upgrade, while others are corrections and

supplementary explanations.

Changes due to the software upgrade

❏ Support for CobraNet “Low Latency” (system software v1.10)

In conjunction with the upgrade to system software V1.10, the latency setting that had been ﬁxed at 5.33 ms can now be

selected from three choices (5.33 ms/2.67 ms/1.33 ms). This allows even lower-latency distribution of audio signals. In

addition, you can now make connections at the desired latency to digital mixers such as the PM5D or digital mixing engines

such as the DME64N/24N via the Yamaha “MY16-C” card.

Changing the latency can be done in conjunction with NetworkAmp Manager V1.1.0E. For the procedure, refer to the

NetworkAmp Manager owner’s manual (PDF format).

The latency and audio bit depth settings will determine the limits on the number of channels that can be distributed in one

bundle, and the number of bundles that can be distributed.

• NHB32-C

•ACU16-C

If two or more different latencies exist in a CobraNet network, it may become impossible for the various devices to

communicate correctly. You must make sure that all CobraNet devices in a single network have the same latency setting.

Additions and corrections

❏ Cable Length & Switching Hubs

The maximum length of a cable used in a 100Base-T Ethernet network is 100 m (a maximum of 2 km for a multimode optical

ﬁber cable), but depending on the type of cable used and on the performance of the switching hub, there are cases in which

this length cannot be guaranteed. Three or four switching hubs can be connected, but this also will depend on the

performance of the switching hub.

❏ “System Requirements (NetworkAmp Manager)” (page 10)

The following items have been added to the operating requirements for NetworkAmp Manager.

•If your computer has HyperThreading Technology, you must disable it when connecting via USB.

•This software cannot be used on a computer that has multiple CPUs (e.g., Intel’s Xeon processor or AMD’s Opteron

processor).

•This software cannot be used on a computer that has a dual core CPU (e.g., Intel’s Pentium-D processor or AMD’s

Athlon64 x2 processor).

•This software cannot be used on a computer running Windows XP x64 Edition.

Latency

20-bit 24-bit

Channels per

bundle

Maximum number of bundles

(total of input and output)

Channels per

bundle

Maximum number of bundles

(total of input and output)

5.33ms 8 8 7 8

2.67ms 8 8 8 8

1.33ms 8 4 8 4

Latency

Maximum number of

bundles (input only)

5.33ms 4

2.67ms 4

1.33ms 4

– 3 –

❏ “Installing Acrobat Reader” (page 12)

Incorrect—To view the Network Amp Manager Owner’s Manual, you’ll need to install the Adobe Acrobat Reader

software, which is included on the CD-ROM. If you already have this software installed, skip this section.

Correct—To view the NetworkAmp Manager Owner’s Manual (PDF format), Adobe Reader software (free of charge)

must be installed. If you don’t have Adobe Reader, please download it from the Adobe Corporation’s website.

http://www.adobe.com

❏ “PRIMARY & SECONDARY CobraNet ports” (page 22)

Incorrect—Primary and secondary can be used to build redundancy into systems. Under normal conditions, the

ACU16-C uses the PRIMARY port. However, if communication via that port fails, it will automatically switch to the

SECONDARY port and operation will continue uninterrupted.

Correct—Primary and secondary can be used to build redundancy into systems. Under normal conditions, the ACU16-

C uses the PRIMARY port. However, if system problems such as port malfunction or broken cable occur in the PRIMARY

port, it will automatically switch to the SECONDARY port. The audio signal will be momentarily interrupted, but the

duration of the interruption will depend on the performance and settings of the hub, and on the structure of the system.

❏ “Introduction” (page 25)

Incorrect—Up to eight NHB32-Cs can be used on a single CobraNet network, providing bridging between 512

CobraNet audio channels and 512 AES/EBU format inputs and outputs.

Correct—Up to eight NHB32-Cs can be used on a single CobraNet network, providing bridging a maximum (total

inputs and outputs) of 256 channels of CobraNet audio and AES/EBU audio.

❏ “CobraNet Primary & Secondary” (page 35)

Incorrect—In the ﬁrst example, if a primary connection fails, the system automatically switches to secondary and

operation continues uninterrupted. However, if the switching hub fails, the entire system stops working. In the second

example, individual switching hubs are used for primary and secondary, so even if switching hub A fails, operation

continues on secondary via switching hub B.

Correct—In the ﬁrst example, if a primary connection fails, the system automatically switches to secondary. However if

the switching hub fails, the entire system stops working. In the second example, individual switching hubs are used for

primary and secondary, so even if switching hub A fails, operation continues on secondary via switching hub B.

Be aware that with either connection, the time required in order to switch between primary and secondary will depend on

the performance and settings of the hub.

❏ “CobraNet Primary & Secondary, Ex. 2” (page 35)

In consideration of a case in which the primary connection fails, connect switching hub A and switching hub B.

NETWORK HUB AND BRIDGE

LINK CONDUCT

LOCK

ERROR

NETWORK HUB AND BRIDGE

LINK CONDUCT

LOCK

ERROR

ACU16-C ACU16-C

NHB32-C NHB32-C

Ethernet switching hub A

Ethernet switching hub B

Primary CobraNet

Secondary CobraNet

ENGLISH

M.D.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation

ACU16-C/NHB32-C

fan kit/Lüftereinheit/

Kit de ventilation/Kit de ventilación

ventilation panel/Lüftungsblenden/

Panneau de ventilation/Panel de ventilación

ventilation panel/Lüftungsblenden/

Panneau de ventilation/Panel de ventilación

Notes on rack-mounting the unit

If you install the ACU16-C/NHB32-C along with another

ACU16-C/NHB32-C or other device in a rack that is not well

ventilated, the temperature inside the rack may rise due to the

heat generated from the devices and the devices may be unable

to perform properly. When you rack-mount the unit, be sure

to keep a gap of 1U (4.5cm) above and below the unit for better

ventilation. Also, install the ventilation panels in these gaps or

remove the partition panels.

If the temperature inside the rack is expected to be 40°C or

higher (in this case, the room temperature is generally about

30°C or higher), install the fan kit on the top shelf of the rack,

and install the ventilation panels between devices or remove

the partition panels. The fan kit must generate a maximum

wind of 1.6m

/min or higher and a maximum static pressure

of 5mmH

O or higher.

Anmerkungen zum Rackeinbau des Geräts

Wenn Sie den ACU16-C/NHB32-C gemeinsam mit einem

anderen ACU16-C/NHB32-C oder einem Gerät mit

mangelhafter Lüftung in ein Rack einbauen, könnte die

Te mperatur im Innern des Racks rapide ansteigen und Ausfälle

der vorhandenen Geräte verursachen. Lassen Sie über und unter

Geräten in einem Rack jeweils 1HE (4,5cm) frei, um eine

ausreichende Luftzirkulation zu gewährleisten. In diesen

Öffnungen müssen Lüftungsblenden angebracht werden.

Außerdem sind eventuell vorhandene Trennplatten zu entfernen.

Wenn die Temperatur im Innern des Racks die 40°C-Marke zu

übersteigen droht (was der Fall ist, wenn die Raumtemperatur

mindestens 30°C beträgt), müssen Sie ganz oben im Rack eine

Lüftereinheit und zwischen den Geräten Lüftungsblenden

einbauen. Trennplatten zwischen diesen Partien müssen

entfernt werden. Die Lüftereinheit muss einen Luftstrom von

mindestens 1,6m

/min und einen statischen Druck von

5mmH

O oder mehr erzeugen.

Remarques concernant l’installation de l’unité dans un rack

Si vous installez l’ACU16-C/NHB32-C dans le même rack

qu’un deuxième ACU16-C/NHB32-C ou tout autre dispositif

avec une ventilation autonome plutôt limitée, la température au

sein du rack pourrait très vite monter à des valeurs qui

empêchent les unités de fonctionner correctement. De ce fait,

pour le montage en rack, il convient de laisser un espace d’1U

(4,5cm) au-dessus et en dessous de tels dispositifs pour assurer

une bonne circulation d’air frais. De plus, il faut couvrir les

ouvertures ainsi laissées avec des panneaux de ventilation.

Retirez toute cloison éventuellement présente entre deux unités.

Si la température au sein du rack risque de monter au-delà de

40°C (auquel cas la température ambiante s’élève à 30°C ou

plus), installez un kit de ventilation en haut du rack et des

panneaux de ventilation entre les unités. Retirez en outre les

cloisons qui les séparent. Le kit de ventilation doit générer un

ﬂux d’air supérieur à 1,6m

/min et une pression statique de

5mmH

O ou plus.

Notas acerca de la instalación en rack de la unidad

Si instala el ACU16-C/NHB32-C junto con otro ACU16-C/

NHB32-C u otro dispositivo en un armario rack que no esté

correctamente ventilado, la temperatura en el interior del

armario puede elevarse debido al calor generado por los

propios dispositivos y afectar al correcto funcionamiento de

los mismos. Cuando instale la unidad en rack, asegúrese de

dejar una separación de 1U (4.5cm) por encima y por debajo

de la unidad con el ﬁn de conseguir una correcta ventilación.

Además, instale los paneles de ventilación en estas

separaciones o elimine los paneles de partición.

Si se calcula que la temperatura en el interior del rack sea de

40°C o más (en este caso, cuando la temperatura de la

habitación es de 30°C o superior), instale el kit de ventilación

en la parte superior del armario rack e instale los paneles de

ventilación entre los dispositivos o elimine los paneles de

división. El kit de ventilación debe generar un caudal mínimo

de 1.6m

/min o superior con una presión estática mínima de 5

mm H

O o superior.

ACU NHB Pera_M_A Page 1 Wednesday, April 23, 2003 4:38 PM

M.D.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation

Important Note for PC-N Series Power

Ampliﬁer Users

When you are using the ACU16-C connected to a PC9500N or

PC4800N power ampliﬁer, the NetworkAmp Manager's meter

may not display the correct value, depending on your power

ampliﬁer. Please check your power ampliﬁer for the following

items to ﬁnd out whether the problem has been ﬁxed on your

ampliﬁer:

Locate the product serial number label on the packing container

or on the rear panel of the power ampliﬁer.

•If the ﬁrst two alphabetical letters in the serial number are IL,

IM, IN, IO, IP, IX, IY, IZ, or JH, the problem may not have

been ﬁxed on the ampliﬁer. Otherwise, you can assume that

the problem has been ﬁxed on your ampliﬁer.

• On units that have a serial number that begins with any of the

letter combinations described above, if there is a green round

sticker adjacent to the serial number label, the problem has

been ﬁxed on the unit.

If the problem has not been ﬁxed on your power ampliﬁer,

contact your Yamaha dealer.

Wichtiger Hinweis für den Einsatz von

Endstufen der PC-N-Serie

Wenn Sie den ACU16-C an eine Endstufe des Typs PC9500N

oder PC4800N anschließen, zeigen die Meter von NetworkAmp

Manager eventuell nicht den richtigen Wert an. Wenn das bei

Ihnen der Fall ist, können Sie folgendermaßen ermitteln, ob das

Problem der Endstufe behoben werden muss:

Bringen Sie die Seriennummer Ihrer Endstufe in Erfahrung.

Diese ﬁnden Sie auf dem Lieferkarton und dem rückseitigen

Typenschild.

•Wenn die ersten beiden Buchstaben der Seriennummer „IL”,

„IM”, „IN”, „IO”, „IP”, „IX”, „IY”, „IZ” oder „JH” lauten,

bedarf die Endstufe eventuell noch einer Aktualisierung.

Andernfalls können Sie davon ausgehen, dass das Problem

bereits behoben wurde.

•Auf Geräten, deren Seriennummer mit den oben erwähnten

Buchstaben beginnt und bei denen das Problem bereits

behoben wurde, beﬁndet sich neben dem Typenschild ein

runder grüner Aufkleber.

Fehlt dieser Aufkleber auf Ihrer Endstufe, so wenden Sie sich

bitte an Ihren Yamaha-Händler.

Remarque importante à l’attention

des utilisateurs d’un ampliﬁcateur de

puissance de la série PC-N

Quand l’ACU16-C est branché à un ampliﬁcateur de puissance

PC9500N ou PC4800N, il se peut (selon l’ampli de puissance)

que l’afﬁchage de niveau de NetworkAmp Manager n’indique

pas la valeur correcte. Contrôlez alors le numéro de série de

votre ampliﬁcateur comme suit pour vériﬁer si ce problème doit

être corrigé ou non:

Vériﬁez le numéro de série de l’ampliﬁcateur sur l’emballage ou

le panneau arrière de l’appareil.

•Si les deux premières lettres du numéro de série

correspondent à “IL”, “IM”, “IN”, “IO”, “IP”, “IX”, “IY”, “IZ” ou

“JH”, le problème n’a peut-être pas été corrigé sur

l’ampliﬁcateur. Si les lettres initiales du numéro de série

diffèrent des caractères ci-dessus, vous pouvez partir du

principe que le problème a été corrigé sur votre

ampliﬁcateur.

•Certains ampliﬁcateurs dont le numéro de série commence

par une paire de lettres mentionnée ci-dessus pourraient

comporter une vignette ronde et verte collée à côté de

l’étiquette du numéro de série. La présence de cette vignette

signiﬁe que le problème a été corrigé sur l’appareil en

question.

Si le problème n’a pas été corrigé sur votre ampliﬁcateur de

puissance, contactez votre revendeur Yamaha.

Nota importante para los usuarios de

los ampliﬁcadores de la serie PC-N

Si utiliza el ACU16-C conectado a un ampliﬁcador PC9500N o

PC4800N, el indicador NetworkAmp del Manager puede que no

visualice el valor correcto, dependiendo de su ampliﬁcador.

Compruebe los siguientes elementos en su ampliﬁcador para

saber si el problema se ha solucionado:

Localice la etiqueta del número de serie del producto en el

embalaje o en el panel posterior del ampliﬁcador.

•Si las dos primeras letras del número de serie son “IL”, “IM”,

“IN”, “IO”, “IP”, “IX”, “IY”, “IZ” o “JH”, es posible que el

problema no se haya solucionado en el ampliﬁcador. De lo

contrario, puede asumir que el problema se ha solucionado

en el ampliﬁcador.

• En las unidades con números de serie que empiecen por

cualquier serie de letras mencionada, si observa un punto

verde al lado de la etiqueta del número de serie, el problema

se ha solucionado en la unidad.

Si el problema persiste en el ampliﬁcador, contacte con su

distribuidor Yamaha.

ACU NHB Pera_M_A Page 1 Wednesday, April 23, 2003 10:04 AM

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions

contained in this manual,

meets FCC

requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting

this product to accessories and/or another product use only high quality shielded cables. Cable/s

supplied with this product MUST

be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations,

Part 15 for Class “B”

digital devices. Compliance with

these requirements

provides a reasonable level of assurance

that your use of this product

in a residential

environment will not

result in harmful interference

with

other electronic devices. This equipment generates/uses

radio frequencies and, if not installed and used according to the instructions

found in the users manual, may

cause interference

harmful to the operation of other electronic

devices. Compliance with FCC regulations

does not guarantee that

interference

will not occur in all

installations. If this product is found to be the source of interference,

which can be determined by turning the unit “OFF” and

“ON”, please try to eliminate the

problem by using

one of the following measures:

Relocate either

this product or

the device that

is being affected

by the interfe

rence. Utilize power outlets

that are on

different branch (circuit

breaker or fuse)

circuits or install

AC line filter/s.

In the case

of radio or TV interference, relocate/reorient

the antenna. If

the antenna lead-in

is 300 ohm ribbon lead, change the lead-in to coaxial type cable. If these corrective

measures do not produce satisfactory results,

please contact the local retailer

authorized to distribute this type of product.

If you can not locate the appropriate retailer,

please contact

Yamaha Corporation

of America,

Electronic Service

Division, 6600 Orangethorpe Ave, Buena Park, CA 90620

The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.

WARNING: THIS APPARATUS MUST BE EARTHED

IMPORTANT

THE WIRES IN THIS MAINS LEAD ARE COLOURED IN

CCORDANCE WITH THE FOLLOW

ING CODE

GREEN-A

ND-YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus may

not correspond with the coloured markings identifying the terminals in

your plug, proceed as follows:

The wire which is coloured GREEN and YELLOW must be

connected to the terminal in the plug which is marked by the letter E

or by the safety earth symbol or coloured GREEN and YELLOW.

The wire which is coloured BLUE must be connected to the terminal

which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the

terminal which is marked with the letter L or coloured RED.

*This applies only to products distributed by YAMAHA KEMBLE

MUSIC (U.K.) LTD.

The above warning is located on the top of the unit.

Explanation of Graphical Symbols

The lightning ﬂash with arrowhead symbol

within an equilateral triangle is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufﬁcient magnitude

to constitute a risk of electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and mainte-

nance (servicing) instructions in the literature

accompanying the product.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instruc-

tions.

8 Do not install near any heat sources such as

radiators, heat registers, stoves, or other appa-

ratus (including ampliﬁers) that produce heat.

9 Do not defeat the safety purpose of the polar-

ized or grounding-type plug. A polarized plug

has two blades with one wider than the other. A

grounding type plug has two blades and a third

grounding prong. The wide blade or the third

prong are provided for your safety. If the pro-

vided plug does not ﬁt into your outlet, consult

an electrician for replacement of the obsolete

outlet.

10 Protect the power cord from being walked on or

pinched particularly at plugs, convenience

receptacles, and the point where they exit from

the apparatus.

11 Only use attachments/accessories speciﬁed by

the manufacturer.

12 Use only with the cart, stand,

tripod, bracket, or table spec-

iﬁed by the manufacturer, or

sold with the apparatus.

When a cart is used, use cau-

tion when moving the cart/

apparatus combination to

avoid injury from tip-over.

13 Unplug this apparatus during lightning storms

or when unused for long periods of time.

14 Refer all servicing to qualiﬁed service person-

nel. Servicing is required when the apparatus

has been damaged in any way, such as power-

supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus,

the apparatus has been exposed to rain or mois-

ture, does not operate normally, or has been

dropped.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

ACU16-C & NHB32-C Owner’s Manual

Software Licensing Agreement

The following is a legal agreement between you, the end user, and Yamaha Corporation

(“Yamaha”). The enclosed Yamaha software program is licensed by Yamaha to the original

purchaser for use only on the terms set forth herein. Please read this licensing agreement

with care. Opening this package indicates that you accept all terms outlined herein. If you

do not agree to the terms, return this package unopened to Yamaha for a full refund.

GRANT OF LICENSE AND COPYRIGHT:

Yamaha grants you, the original purchaser,

the right to use one copy of the enclosed software program and data (“SOFTWARE”) on a

single-user computer system. You may not use it on more than one computer or computer

terminal. The SOFTWARE is owned by Yamaha and is protected by Japanese copyright laws

and all applicable international treaty provisions. You are entitled to claim ownership of the

media in which the SOFTWARE is included. Therefore, you must treat the SOFTWARE like

any other copyrighted materials.

RESTRICTIONS:

The SOFTWARE program is copyrighted. You may not engage in

reverse engineering or reproduction of the SOFTWARE by other conceivable methods. You

may not reproduce, modify, change, rent, lease, resell, or distribute the SOFTWARE in

whole or in part, or create derivative works from the SOFTWARE. You may not transmit or

network the SOFTWARE with other computers. You may transfer ownership of the SOFT-

WARE and the accompanying written materials on a permanent basis provided that you

retain no copies and the recipient agrees to the terms of the licensing agreement.

TERMINATION:

The licensing condition of the software program becomes effective on

the day that you receive the SOFTWARE. If any one of the copyright laws or clauses of the

licensing conditions is violated, the licensing agreement shall be terminated automatically

without notice from Yamaha. In this case, you must destroy the licensed SOFTWARE and

its copies immediately.

PRODUCT WARRANTY:

Yamaha warrants to the original purchaser that if the SOFT-

WARE, when used in normal conditions, will not perform the functions described in the

manual provided by Yamaha, the sole remedy will be that Yamaha will replace any media

which proves defective in materials or workmanship on an exchange basis without charge.

Except as expressly set forth above, the SOFTWARE is provided “as is,” and no other war-

ranties, either expressed or implied, are made with respect to this software, including, with-

out limitation the implied warranties of merchantability and ﬁtness for a particular

purpose.

LIMITED LIABILITY:

Your sole remedies and Yamaha’s entire liability are as set forth

above. In no event will Yamaha be liable to you or any other person for any damages, includ-

ing without limitation any incidental or consequential damages, expenses, lost proﬁts, lost

savings or other damages arising out of the use or inability to use such SOFTWARE even if

Yamaha or an authorized dealer has been advised of the possibility of such damages, or for

any claim by any other party.

GENERAL:

This license agreement shall be interpreted according to and governed by Jap-

anese laws.

ACU16-C & NHB32-C Owner’s Manual

ENGLISH

Precautions

Warnings

Installation

•Connect this unit’s power cord only to an AC outlet of the type stated in this

Owner’s Man-

ual

or as marked on the unit. Failure to do so is a ﬁre and electrical shock hazard.

•Do not allow water to enter this unit or allow the unit to become wet. Fire or electrical shock

may result.

•Do not place heavy objects, including this unit, on top of the power cord. A damaged power

cord is a ﬁre and electrical shock hazard. In particular, be careful not to place heavy objects

on a power cord covered by a carpet.

•Do not place a container with liquid or small metal objects on top of this unit. Liquid or

metal objects inside this unit are a ﬁre and electrical shock hazard.

Operation

•Do not scratch, bend, twist, pull, or heat the power cord. A damaged power cord is a ﬁre

and electrical shock hazard.

•Do not remove the unit’s cover. You could receive an electrical shock. If you think internal

inspection, maintenance, or repair is necessary, contact your dealer.

•Do not modify the unit. Doing so is a ﬁre and electrical shock hazard.

•If lightning begins to occur, turn off the power switch of the unit as soon as possible, and

unplug the power cable plug from the electrical outlet.

•If there is a possibility of lightning, do not touch the power cable plug if it is still connected.

Doing so may be an electrical shock hazard.

•Use only the included power cord with this unit. Using other types may be a ﬁre and elec-

trical shock hazard.

In case an abnormality occurs during operation

•If the power cord is damaged (i.e., cut or a bare wire is exposed), ask your dealer for a

replacement. Using the unit with a damaged power cord is a ﬁre and electrical shock hazard.

•If you notice any abnormality, such as smoke, odor, or noise, or if a foreign object or liquid

gets inside the unit, turn it off immediately. Disconnect the power cord. Consult your dealer

for repair. Using the unit in this condition is a ﬁre and electrical shock hazard.

• Should this unit be dropped or the cabinet be damaged, turn the power switch off, remove

the power plug from the AC outlet, and contact your dealer. If you continue using the unit

without heeding this instruction, ﬁre or electrical shock may result.

ACU16-C & NHB32-C Owner’s Manual

Cautions

Installation

•Keep this unit away from the following locations:

—Locations exposed to oil splashes or steam, such as near cooking stoves, humidiﬁers, etc.

—Unstable surfaces, such as a wobbly table or slope.

—Locations exposed to excessive heat, such as inside a car with all the windows closed, or

places that receive direct sunlight.

—Locations subject to excessive humidity or dust accumulation.

•Hold the power cord plug when disconnecting it from an AC outlet. Never pull the cord. A

damaged power cord is a potential ﬁre and electrical shock hazard.

•Do not touch the power plug with wet hands. Doing so is a potential electrical shock hazard.

•This unit has ventilation holes to prevent the internal temperature from rising too high. Do

not block them. Blocked ventilation holes are a ﬁre hazard. In particular, do not operate the

unit while it’s on its side, is upside down, or while it’s covered with a cloth or dust sheet.

•When installing the unit in a rack, you must use the rack-mounting screw holes at the rear

in addition to those on the front panel.

•When rack-mounting or stacking several units, always leave at least 1U (i.e., about 4.5 cm)

of free space above and below the unit for normal ventilation. If the airﬂow is restricted, the

unit may overheat, which could cause a ﬁre.

•To relocate the unit, turn the power switch off, remove the power plug from the AC outlet,

and remove all connecting cables. Damaged cables may cause ﬁre or electrical shock.

•This unit is equipped with a dedicated ground connection to prevent electrical shock.

Before connecting the power plug to an AC outlet, be sure to ground the unit. If the power

cord has a three-pin plug, it will provide sufﬁcient grounding so long as the AC outlet is

grounded correctly.

Operation

•If you know you will not use this unit for a long period of time, such as when going on vaca-

tion, remove the power plug from the AC outlet. Leaving it connected is a potential ﬁre haz-

ard.

Maintenance

•To prevent electrical shock when cleaning the unit, remove the power plug from the AC out-

let.

ACU16-C & NHB32-C Owner’s Manual

ENGLISH

Important Information

Operating Notes

•The performance of components with moving contacts, such switches, rotary controls, fad-

ers, and connectors, deteriorates over time. The rate of deterioration depends on the oper-

ating environment and is unavoidable. Consult your dealer about replacing defective

components.

•Using a mobile telephone near this unit may induce noise. If noise occurs, use the telephone

away from the unit.

•The digital circuits of this unit may induce a slight noise into nearby radios and TVs. If noise

occurs, relocate the affected equipment.

•When connecting D-sub cables, be sure to tighten the screws on both sides of the connector

securely. To disconnect the cable, loosen the screws completely, then remove the cable by

holding the connector part. Do not remove the plug by pulling the cable while the screws

are still attached. Otherwise, the connector may be damaged, leading to malfunction.

•When you change the wordclock settings on any device in your digital audio system, some

devices may output noise, so turn down your power amps beforehand, otherwise your

speakers may be damaged.

Special Notices

•The software and this owner’s manual are the exclusive copyrights of Yamaha Corporation.

•Use of the software and this manual is governed by the license agreement which the pur-

chaser fully agrees to upon breaking the seal of the software packaging. (Please read care-

fully the Software Licensing Agreement at the beginning of this manual before installing the

application.)

•Copying of the software or reproduction of this manual in whole or in part by any means is

expressly forbidden without the written consent of the manufacturer.

•Yamaha makes no representations or warranties with regard to the use of the software and

documentation and cannot be held responsible for the results of the use of this manual and

the software.

•This disc is a CD-ROM. Do not attempt to play the disc on an audio CD player. Doing so

may result in irreparable damage to your audio CD player.

•Copying of the commercially available music sequence data and/or digital audio ﬁles is

strictly prohibited except for your personal use.

•The screen displays as illustrated in this owner’s manual are for instructional purposes, and

may appear somewhat different from the screens which appear on your computer.

•Future upgrades of application and system software and any changes in speciﬁcations and

functions will be announced separately.

ACU16-C & NHB32-C Owner’s Manual

Trademarks

Adobe, Acrobat, and Reader are registered trademarks of Adobe Systems Incorporated.

CobraNet and Peak Audio are trademarks of Cirrus Logic, Inc. Ethernet is a trademark of

Xerox Corporation. Intel and Pentium are registered trademarks of Intel Corporation.

Microsoft and Windows are registered trademarks of Microsoft Corporation, Inc. Yamaha

is a trademark of Yamaha Corporation. All other trademarks are the property of their

respective holders and are hereby acknowledged.

Yamaha Web Site

Further information about this unit, related products, and other Yamaha professional audio

equipment is available on the Yamaha Professional Audio Web site at:

<http://www.yamaha.co.jp/product/proaudio/homeenglish/>.

Package Contents

ACU16-C

•ACU16-C Amp Control Unit

• CD-ROM (NetworkAmp Manager, PDF manual

MIDI drivers)

•Power cord and retaining clamp

• USB cable (for connection to PC running NetworkAmp Manager)

•3-way Euro-block connectors x16

•This manual

NHB32-C

• NHB32-C Network Hub and Bridge

• CD-ROM (NetworkAmp Manager, PDF manual

MIDI drivers)

•Power cord and retaining clamp

• USB cable (for connection to PC running NetworkAmp Manager)

•This manual

About this Owner’s Manual

This

Owner’s Manual

consists of three main sections:

•NetworkAmp Manager Installation

•ACU16-C Amp Control Unit

• NHB32-C Network Hub and Bridge

All the information you need in order to install NetworkAmp Manager, and to operate the

ACU16-C and NHB32-C is contained in this manual. Although the ACU16-C and

NHB32-C can be used standalone, ﬁrst they need to be conﬁgured using NetworkAmp

Manager. The PDF format

Network Amp Manager Owner’s Manual

, which contains a glos-

sary of NetworkAmp Manager, ACU16-C, and NHB32-C related terms, is on the supplied

CD-ROM.

A wealth of information about CobraNet, with sections especially for designers and install-

ers, is available on the Peak Audio Web site at <http://www.peakaudio.com>. If you are

designing a CobraNet network, we strongly recommend that you visit this Web site and

study the information available in order to fully understand the CobraNet technology. Peak

Audio also provide a list of Ethernet devices that have been tested with CobraNet, including

switching hubs and media converters.

ACU16-C & NHB32-C Owner’s Manual

ENGLISH

Contents

1 NetworkAmp Manager Installation . . . . . . . . . . . 10

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

CD-ROM Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

ACU16-C/NHB32-C Hookup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Installing Acrobat Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Installing the USB MIDI Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Installing the Yamaha CBX Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Installing NetworkAmp Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Starting NetworkAmp Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Installation Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

2 ACU16-C Amp Control Unit . . . . . . . . . . . . . . . . . 20

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

3 NHB32-C Network Hub & Bridge . . . . . . . . . . . . . 25

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

4 System Examples . . . . . . . . . . . . . . . . . . . . . . . . . . 32

ACU16-C Power Amp Control System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

ACU16-C/NHB32-C CobraNet Audio Distribution System . . . . . . . . . . . . . . . . 33

MIDI Over CobraNet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

AD824 Control Over CobraNet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

CobraNet Primary & Secondary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

System Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Connector Wiring Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

NetworkAmp Manager Installation

ACU16-C & NHB32-C Owner’s Manual

1 NetworkAmp Manager Installation

Introduction

This chapter

explains how to install NetworkAmp Manager and the necessary drivers. For

information on how to use NetworkAmp Manager, refer to the

Network Amp Manager

Owner’s Manual,

which is included on the CD-ROM in PDF format and can be opened

directly from NetworkAmp Manager’s Help menu.

CD-ROM Contents

System Requirements

The system requirements of your operating system may be different to those listed here.

NetworkAmp Manager

Yamaha USB MIDI Driver

Yamaha CBX Driver

System requirements for software not listed here can be found on the CD-ROM.

Folder Software Description

Acroread\English

Acrobat Reader

1. For details on using this software, refer to the PDF manual after installation.

2. This software is not supported by Yamaha.

Adobe Acrobat Reader software for view-

ing the PDF format manuals.

NetworkAmp Manager

NetworkAmp Manager program and

PDF format manual.

Mididrv_

Yamaha CBX Driver

Yamaha serial driver. Necessary if you are

connecting to a serial port on your PC.

USBdrv_

Yamaha USB MIDI Driver

(Windows 98, Me)

Yamaha USB driver. Necessary if you are

connecting to a USB port on your PC.

USBdrv2k_

Yamaha USB MIDI Driver

(Windows 2000, XP)

Computer

PC with a 450 MHz or faster Intel Pentium or Celeron family processor

Windows 98, 98SE, Me, 2000, XP Home Edition, XP Professional

Memory

64 MB or more (128 MB or more recommended)

Hard Disk

100 MB or more of free space

Display

1024 x 768 pixels, 32,000 colors or higher

Computer

PC with a 166 MHz or faster Intel Pentium or Celeron family processor and USB port

Windows 98, 98SE, Me, 2000, XP Home Edition, XP Professional

Memory

32 MB or more

Hard Disk

2 MB or more of free space

Windows 95, 98, 98SE, Me, NT4.0, 2000, XP Home Edition, XP Professional

ACU16-C/NHB32-C Hookup

ACU16-C & NHB32-C Owner’s Manual

ENGLISH

ACU16-C/NHB32-C Hookup

The following illustration shows the hookup methods that can be used to connect the

ACU16-C/NHB32-C to your computer: USB or serial.

Note:

Before you connect to serial ports, turn off the ACU16-C/NHB32-C and your computer.

USB cable

USB port

TO COMPUTER port

(9-pin D-sub)

USB port

Windows PC running

NetworkAmp Manager

Serial cable

Serial port

(RS-232C)

1. USB

2. Serial

ACU16-C

NHB32-C

ACU16-C

NHB32-C

NETWORK HUB AND BRIDGE

LINK CONDUCT

LOCK

ERROR

NetworkAmp Manager Installation

ACU16-C & NHB32-C Owner’s Manual

Installing Acrobat Reader

To view the

Network Amp Manager Owner’s Manual,

you’ll need to install the Adobe Acro-

bat Reader software, which is included on the CD-ROM. If you already have this software

installed, skip this section.

Start your computer and Windows, and insert the included CD-ROM into

your computer’s CD-ROM drive.

On the CD-ROM, double-click the “Acroread_” folder.

This folder contains Acrobat software in several languages.

Double-click the folder of the language you want to install.

Double-click “ar******.exe.”

(“******” indicates the version number and selected lan-

guage.)

Follow the on-screen instructions to install the software.

For instructions on using Acrobat Reader, choose Reader Help from Acrobat Reader’s Help

menu.

Installing the USB MIDI Driver

If you are connecting the ACU16-C/NHB32-C to a USB port on your computer, you’ll need

to install the Yamaha USB driver. If you already have this software installed, skip this section.

The procedure for installing the Yamaha USB driver depends on the version of Windows

that you are using.

•Windows 98 & 98SE, see page 13

•Windows Me, see page 15

•Windows 2000, see page 16

•Windows XP, see page 17

NetworkAmp

Manager

ACU16-C/NHB32-C

Computer

USB cable

USB MIDI

driver

Installing the USB MIDI Driver

ACU16-C & NHB32-C Owner’s Manual

ENGLISH

Windows 98 & 98SE

Start your computer and Windows, and insert the included CD-ROM into

your computer’s CD-ROM drive.

Turn off the ACU16-C/NHB32-C and use a USB cable to connect the USB port

on the ACU16-C/NHB32-C to a USB port on your computer.

3 Turn on the ACU16-C/NHB32-C.

The Add New Hardware Wizard appears. If it doesn’t appear, try disconnecting and recon-

necting the USB cable. Alternatively, open the Add New Hardware control panel.

4 Click Next.

The following window appears.

14 NetworkAmp Manager Installation

ACU16-C & NHB32-C Owner’s Manual

5 Select “Search for the best driver for your device (Recommended),” and then

click Next.

The following window appears.

6 Select “Specify a location,” and specify “D:\USBdrv_” (replacing “D” with

the drive letter of your CD-ROM drive), and then click Next.

When the driver is located, “YAMAHA USB MIDI Driver” is displayed, as shown below.

7 Click Next.

The driver is installed, and the following window appears when the installation is complete.

8 Click Finish, and then restart your computer.

Note: Yo u may be prompted to insert your Windows CD-ROM. Do not insert it! Click OK,

and in the “Copy ﬁles from” section of the subsequent dialog box, enter “D:\USBdrv_” (replac-

ing “D” with the drive letter of your CD-ROM drive), and then click OK.

Installing the USB MIDI Driver 15

ACU16-C & NHB32-C Owner’s Manual

ENGLISH

Windows Me

1 Start your computer and Windows, and insert the included CD-ROM into

your computer’s CD-ROM drive.

2 Turn off the ACU16-C/NHB32-C and use a USB cable to connect the USB port

on the ACU16-C/NHB32-C to a USB port on your computer.

3 Turn on the ACU16-C/NHB32-C.

The Add New Hardware Wizard appears. If it doesn’t appear, try disconnecting and recon-

necting the USB cable. Alternatively, open the Add New Hardware control panel.

4 Select “Automatic search for a better driver (Recommended),” and then click

Next.

Windows Me should be able to locate the driver automatically, in which case you can pro-

ceed to Step 5. If the driver cannot be located, select “Specify the location of the driver

(Advanced),” click Next, specify your CD-ROM drive (e.g., D:\USBdrv_), and then con-

tinue as prompted.

The following window appears when the installation is complete.

5 Click Finish, and then restart your computer.

16 NetworkAmp Manager Installation

ACU16-C & NHB32-C Owner’s Manual

Windows 2000

1 Start your computer and Windows, log on as the Administrator, and then

insert the included CD-ROM into your computer’s CD-ROM drive.

2 Go to My Computer–>Control Panel–>System–>Hardware–>Driver Sign-

ing–>File Signature Veriﬁcation, select “Ignore—Install all ﬁles, regardless of

ﬁle signature,” and then click OK.

3 Turn off the ACU16-C/NHB32-C and use a USB cable to connect the USB port

on the ACU16-C/NHB32-C to a USB port on your computer.

4 Turn on the ACU16-C/NHB32-C.

The Found New Hardware Wizard appears.

5 Click Next.

6 Select “Search for a suitable driver for my device (Recommended),” and then

click Next.

7 In the subsequent window, select “CD-ROM drives” only, and then click Next.

The driver is installed, and the message “Completing the Found New Hardware Wizard”

appears.

8 Click Finish, and then restart your computer.

Note: Yo u may be prompted to insert your Windows CD-ROM. Do not insert it! Click OK,

and in the “Copy ﬁles from” section of the subsequent dialog box, enter “D:\USBdrv2k_”

(replacing “D” with the drive letter of your CD-ROM drive), and then click OK.

La pagina sta caricando ...

Yamaha NHB32 Manuale utente

Marca: Yamaha

Modello: NHB32

Categoria: Switch di rete

Tipo: Manuale utente

Questo manuale è adatto anche per

Scarica il pdf

rapporto

in altre lingue

English: Yamaha NHB32 User manual
français: Yamaha NHB32 Manuel utilisateur
español: Yamaha NHB32 Manual de usuario
Deutsch: Yamaha NHB32 Benutzerhandbuch
русский: Yamaha NHB32 Руководство пользователя
Nederlands: Yamaha NHB32 Handleiding
português: Yamaha NHB32 Manual do usuário
dansk: Yamaha NHB32 Brugermanual
čeština: Yamaha NHB32 Uživatelský manuál
polski: Yamaha NHB32 Instrukcja obsługi
svenska: Yamaha NHB32 Användarmanual
Türkçe: Yamaha NHB32 Kullanım kılavuzu
suomi: Yamaha NHB32 Ohjekirja
română: Yamaha NHB32 Manual de utilizare

Yamaha NHB32 Manuale utente

Questo manuale è adatto anche per

Yamaha NHB32 Manuale utente

in altre lingue

Documenti correlati

Altri documenti