Yamaha CVP-103 Manuale utente

Owner’s Manual

IMPORTANT

Check Your Power Supply

Make sure that your local AC mains voltage matches

the voltage specified on the name plate on the bottom

panel. In some areas a voltage selector may be

provided on the bottom panel of the main keyboard

unit near the power cord. Make sure that the voltage

selector is set for the voltage in your area. The voltage

selector is set at 240V when the unit is initially shipped.

To change the setting use a “minus” screwdriver to

rotate the selector dial so that the correct voltage

appears next to the pointer on the panel.

92-469- ➀ (bottom)

ENVIRONMENTAL ISSUES: Yamaha strives to pro-

duce products that are both user safe and environmentally

friendly. We sincerely believe that our products and the

production methods used to produce them, meet these

goals. In keeping with both the letter and the spirit of the

law, we want you to be aware of the following:

Battery Notice: This product MAY contain a small non-

rechargable battery which (if applicable) is soldered in

place. The average life span of this type of battery is ap-

proximately five years. When replacement becomes nec-

essary, contact a qualified service representative to per-

form the replacement.

Warning: Do not attempt to recharge, disassemble, or

incinerate this type of battery. Keep all batteries away

from children. Dispose of used batteries promptly and as

regulated by applicable laws. Note: In some areas, the

servicer is required by law to return the defective parts.

However, you do have the option of having the servicer

dispose of these parts for you.

Disposal Notice: Should this product become damaged

beyond repair, or for some reason its useful life is consid-

ered to be at an end, please observe all local, state, and

federal regulations that relate to the disposal of products

that contain lead, batteries, plastics, etc.

NOTICE: Service charges incurred due to lack of knowl-

edge relating to how a function or effect works (when the

unit is operating as designed) are not covered by the

manufacturer’s warranty, and are therefore the owners

responsibility. Please study this manual carefully and con-

sult your dealer before requesting service.

NAME PLATE LOCATION: The graphic below indi-

cates the location of the name plate. The model number,

serial number, power requirements, etc., are located on

this plate. You should record the model number, serial

number, and the date of purchase in the spaces provided

below and retain this manual as a permanent record of

your purchase.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

PRODUCT SAFETY MARKINGS: Yamaha electronic

products may have either labels similar to the graphics

shown below or molded/stamped facsimiles of these

graphics on the enclosure. The explanation of these graph-

ics appears on this page. Please observe all cautions indi-

cated on this page and those indicated in the safety in-

struction section.

See bottom of Keyboard enclosure for graphic symbol markings.

The exclamation point within the equi-

lateral triangle is intended to alert the

user to the presence of important oper-

ating and maintenance (servicing) in-

structions in the literature accompany-

ing the product.

The lightning flash with arrowhead

symbol, within the equilateral triangle,

is intended to alert the user to the pres-

ence of uninsulated “dangerous volt-

age” within the product’s enclosure that

may be of sufficient magnitude to con-

stitute a risk of electrical shock.

IMPORTANT NOTICE: All Yamaha electronic prod-

ucts are tested and approved by an independent safety

testing laboratory in order that you may be sure that when

it is properly installed and used in its normal and custom-

ary manner, all foreseeable risks have been eliminated.

DO NOT modify this unit or commission others to do so

unless specifically authorized by Yamaha. Product per-

formance and/or safety standards may be diminished.

Claims filed under the expressed warranty may be denied

if the unit is/has been modified. Implied warranties may

also be affected.

SPECIFICATIONS SUBJECT TO CHANGE: The

information contained in this manual is believed to be

correct at the time of printing. However, Yamaha reserves

the right to change or modify any of the specifications

without notice or obligation to update existing units.

SPECIAL MESSAGE SECTION

Model _____________________________________

Serial No. __________________________________

Purchase Date ______________________________

3

CVP-103

• If the instrument has a key cover, take care that the key cover does not pinch

your fingers, and do not insert a finger or hand in the key cover gap.

• If the instrument has a key cover, never insert or drop paper or metallic or

other objects between the slits of the key cover and the keyboard. If this

happens, immediately turn off the power and remove the electric plug from

the outlet and have the instrument inspected by qualified Yamaha service

personnel.

• Do not place the instrument against a wall (allow at least 3 cm/one-inch

from the wall), since this can cause inadequate air circulation, and possibly

result in the instrument overheating.

• Read carefully the attached documentation explaining the assembly pro-

cess. Failure to assemble the instrument in the proper sequence might re-

sult in damage to the instrument or even injury.

• Do not operate the instrument for a long period of time at a high or uncom-

fortable volume level, since this can cause permanent hearing loss. If you

experience any hearing loss or ringing in the ears, consult a physician.

■USING THE BENCH (if included)

• Do not play carelessly with or stand on the bench. Using it as a tool or step-

ladder or for any other purpose might result in accident or injury.

• Only one person should sit on the bench at a time, in order to prevent the

possibility of accident or injury.

• If the bench screws become loose due to extensive long-term use, tighten

them periodically using the included tool.

■SAVING USER DATA

• Always save data to a floppy disk frequently, in order to help prevent the loss

of important data due to a malfunction or user operating error.

Yamaha cannot be held responsible for damage caused by improper use or

modifications to the instrument, or data that is lost or destroyed.

Always turn the power off when the instrument is not in use.

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep these precautions in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock,

short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:

• Do not open the instrument or attempt to disassemble the internal parts or

modify them in any way. The instrument contains no user-serviceable parts.

If it should appear to be malfunctioning, discontinue use immediately and

have it inspected by qualified Yamaha service personnel.

• Do not expose the instrument to rain, use it near water or in damp or wet

conditions, or place containers on it containing liquids which might spill

into any openings.

• If the power cord or plug becomes frayed or damaged, or if there is a sudden

loss of sound during use of the instrument, or if any unusual smells or

smoke should appear to be caused by it, immediately turn off the power

switch, disconnect the electric plug from the outlet, and have the instrument

inspected by qualified Yamaha service personnel.

• Only use the voltage specified as correct for the instrument. The required

voltage is printed on the name plate of the instrument.

• Before cleaning the instrument, always remove the electric plug from the

outlet. Never insert or remove an electric plug with wet hands.

• Check the electric plug periodically and remove any dirt or dust which may

have accumulated on it.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the

instrument or other property. These precautions include, but are not limited to, the following:

• Do not place the power cord near heat sources such as heaters or radiators,

and do not excessively bend or otherwise damage the cord, place heavy

objects on it, or place it in a position where anyone could walk on, trip over,

or roll anything over it.

• When removing the electric plug from the instrument or an outlet, always

hold the plug itself and not the cord. Pulling by the cord can damage it.

• Do not connect the instrument to an electrical outlet using a multiple-con-

nector. Doing so can result in lower sound quality, or possibly cause over-

heating in the outlet.

• Remove the electric plug from the outlet when the instrument is not to be

used for extended periods of time, or during electrical storms.

• Before connecting the instrument to other electronic components, turn off

the power for all components. Before turning the power on or off for all

components, set all volume levels to minimum. Also, be sure to set the

volumes of all components at their minimum levels and gradually raise the

volume controls while playing the instrument to set the desired listening

level.

• Do not expose the instrument to excessive dust or vibrations, or extreme

cold or heat (such as in direct sunlight, near a heater, or in a car during the

day) to prevent the possibility of panel disfiguration or damage to the inter-

nal components.

• Do not use the instrument near other electrical products such as televisions,

radios, or speakers, since this might cause interference which can affect

proper operation of the other products.

• Do not place the instrument in an unstable position where it might acciden-

tally fall over.

• Before moving the instrument, remove all connected cables.

• When cleaning the instrument, use a soft, dry cloth. Do not use paint thinners,

solvents, cleaning fluids, or chemical-impregnated wiping cloths. Also, do

not place vinyl, plastic or rubber objects on the instrument, since this might

discolor the panel or keyboard.

• Do not rest your weight on, or place heavy objects on the instrument, and do

not use excessive force on the buttons, switches or connectors.

(1)B_EL/CL-4vari.

1

4

CVP-103

Thank you for purchasing the Yamaha Clavinova! We recommend that you read this manual care-

fully so that you can fully take advantage of the advanced and convenient functions of the Clavinova.

We also recommend that you keep this manual in a safe and handy place for future reference.

Accessories

● Music Software Collection Disk (and Music Book)

This disk features sample songs that you can play back on your Clavinova, as well as MIDI

driver software for computers.

● Floppy Disk

Use this blank disk to record your performances.

● Owner’s Manual

This manual contains complete instructions for operating your Clavinova.

● Reference Booklet

This manual contains lists of voices, styles, and parameters, etc., as well as specifications

and assembly instructions for your Clavinova.

● Bench

A bench may be included or optional, depending on your locale.

• The CVP-103M will be referred to as the CVP-103 in this Own-

er’s Manual.

• The illustrations and LCD screens as shown in this owner’s

manual are for instructional purposes only, and may appear

somewhat different from those on your instrument.

• Unauthorized copying of copyrighted software for purposes other

than the purchaser’s personal use is prohibited.

● Trademarks:

• Apple and Macintosh are trademarks of Apple Com-

puter, Inc.

• IBM-PC/AT is a trademark of International Business

Machines Corporation.

• Windows is the registered trademark of Microsoft®

Corporation.

• All other trademarks are the property of their respec-

tive holders.

The Panel Logos

The logos printed on the Clavinova panel indicate standards/formats it supports and special features it includes.

Disk Orchestra Collection

The DOC voice allocation format provides data playback com-

patibility with a wide range of Yamaha instruments and MIDI

devices.

Style File Format

The Style File Format (SFF) is Yamaha’s original style file

format, which uses a unique conversion system to provide high-

quality automatic accompaniment based on a wide range of

chord types. The Clavinova uses the SFF internally, reads

optional SFF style disks, and creates SFF styles using the

Custom Style feature.

GM System Level 1

“GM System Level 1” is an addition to the MIDI standard which

guarantees that any data conforming to the standard will play

accurately on any GM-compatible tone generator or synthesizer

from any manufacturer.

XG Format

XG is a new Yamaha MIDI specification which significantly ex-

pands and improves on the “GM System Level 1” standard with

greater voice handling capacity, expressive control, and effect

capability while retaining full compatibility with GM. By using the

Clavinova’s XG voices, it is possible to record XG-compatible

song files.

XF Format

The Yamaha XF format enhances the SMF (Standard MIDI File)

standard with greater functionality and open-ended expandability

for the future. The Clavinova is capable of displaying lyrics when

an XF file containing lyric data is played. (SMF is the most com-

mon format used for MIDI sequence files. The Clavinova is com-

patible with SMF Formats 0 and 1, and records “song” data using

SMF Format 0.)

2

5

CVP-103

Features of the Clavinova

● Easy-to-use LCD Display

The LCD (together with the various panel buttons) provides comprehensive and easy-to-understand

control of the Clavinova’s operations (page 16).

● Wealth of Rich, Realistic Voices

The CVP-103 has a wide variety of authentic and dynamic voices, including 195 original voices,

480 XG voices, and 12 drum/SFX kits. These include exceptionally natural-sounding piano, strings

and brass voices, and the particularly expressive “SweetTrumpet” voice. Moreover, you can play real-

istic drum and percussion sounds directly from the keyboard (page 31).

● Playback of Song Disks

The Clavinova can play back various commercially available song disks. With the appropriate disk

software, you can play the piano part of the song yourself along with a full orchestra or backing band

(page 93). If the software contains lyrics, you can display them on the Clavinova’s LCD.

● Special Guide Functions for Easy Learning

With the appropriate disk software, the LCD display and guide lamps help you learn songs by

showing you when and where to play the proper notes. The three-step system helps you to master each

song quickly and easily (page 105).

● Fun, Dynamic Automatic Accompaniment

The Auto Accompaniment of the Clavinova gives you full, exciting instrumental backing in your

favorite music styles, according to the chords you play (page 57). There’s even a wide selection of

“Pianist” styles that allow you to enjoy solo piano accompaniment (page 58). Choose from 160 ac-

companiment styles, or create your own custom styles (page 73).

● Easy Access to a Variety of Musical Enjoyment

The Clavinova offers several ways to change panel settings without a lot of fuss. You can use the

One Touch Setting feature to select from four sets of voice, effect, and other settings appropriate to

each accompaniment style (page 72). Or access the Music Database to choose from 463 sets of style

and voice settings, selectable by title or style (page 67). You can even save your current setup for in-

stant recall later using the handy Registration function (page 89).

● Easy-to-use Recording Features

You can record songs using a variety of methods, depending on your keyboard expertise and prefer-

ence. Choose from the Quick Recording, Track Recording, and Chord Sequence Recording functions

(page 110).

● Convenient TO HOST Terminals for Direct Connection to Computers

The Clavinova can be used as a high-quality sound source to play back music software for comput-

ers. It can also be used as a master keyboard, to enter performance data and create music with a com-

puter (page 160).

3

6

CVP-103

Table of Contents

4

CHAPTER 1:

Getting Ready

About This Manual 8

Handling the Floppy Disk Drive (FDD) and Floppy Disks 9

Setting Up the Clavinova 10

Music Stand ..................................................................................... 10

Key Cover (Where Present)............................................................. 10

Turning the Power On and Off ......................................................... 11

Headphones..................................................................................... 11

Other Connections ........................................................................... 11

Panel Controls and Terminals 12

Playing the Demo Songs 14

CHAPTER 2:

Basic Operation

Using the LCD Display Controls 16

Selecting a Function ........................................................................ 16

Changing a Setting .......................................................................... 17

Changing a Setting in a Menu Display ............................................. 18

Displaying a Different Page ............................................................. 19

Resetting a Function’s Value ........................................................... 19

Using Functions in Non-rounded Rectangles .................................. 20

Exiting to the Main Display............................................................... 21

Using the Direct Access Function .................................................... 21

Adjusting the Volume 23

Adjusting the Overall Volume........................................................... 23

Adjusting the Accompaniment or Song Volume............................... 23

Setting the Keyboard Volume .......................................................... 23

Adjusting Accompaniment or Song Part Levels............................... 24

Using the Metronome 25

Using the Metronome....................................................................... 25

Changing the Metronome Settings .................................................. 26

Using the Help Mode 27

CHAPTER 3:

Voices

Selecting Voices 29

Selecting a Voice from the VOICE SELECT Display ....................... 29

Selecting Voices from the Main Display........................................... 30

Keyboard Percussion ....................................................................... 31

Changing the Keyboard Settings for the Main Voice ....................... 31

Playing Two Voices Simultaneously — Dual Mode 33

Selecting the Second Voice ............................................................. 33

Changing the Main Voice in Dual Mode........................................... 33

Changing the Keyboard Settings for the Second Voice................... 34

Exiting the Dual Mode...................................................................... 35

Playing Two Voices on Different Sides of the Keyboard

— Split Mode 36

Selecting the Left Voice ................................................................... 36

Changing the Main Voice in Split Mode ........................................... 36

Changing the Keyboard Settings for the Left Voice ......................... 37

Using the Dual and Split Functions Simultaneously ........................ 39

Exiting the Split Mode ...................................................................... 39

Using the Pedals 40

Damper Pedal (Right) ...................................................................... 40

Sostenuto Pedal (Center) ................................................................ 40

Soft Pedal (Left) ............................................................................... 40

CHAPTER 4:

Reverb and Other Effects

Reverb 41

Turning the Reverb On or Off .......................................................... 41

Changing the Reverb Settings ......................................................... 41

Chorus 44

Changing the Chorus Settings ......................................................... 44

Voice Effects 46

Turning the Effects On ..................................................................... 46

Changing the Effect Settings ........................................................... 46

CHAPTER 5:

Accompaniment Styles

(Rhythm and Auto Accompaniment)

Selecting Accompaniment Styles 49

Selecting a Style .............................................................................. 49

Playing the Accompaniment Styles 51

Varying the Style .............................................................................. 51

Starting the Accompaniment Style ................................................... 52

Stopping the Accompaniment Style ................................................. 55

Playing with the Auto Accompaniment 57

Using the Auto Accompaniment....................................................... 57

Starting the Auto Accompaniment ................................................... 58

Stopping the Auto Accompaniment.................................................. 58

Changing the Auto Accompaniment Settings .................................. 59

Adjusting Individual Part Levels ....................................................... 65

Other Auto Accompaniment Functions 67

Music Database ............................................................................... 67

Harmony .......................................................................................... 69

One Touch Setting ........................................................................... 72

Creating Your Own Styles 73

Recording a Custom Style ............................................................... 73

Other Custom Style Functions ......................................................... 80

Playing Back Your Custom Styles ................................................... 84

Messages in Custom Style Mode .................................................... 84

Using Style Files 86

About the Yamaha Style File Format ............................................... 86

Loading Styles from a Disk .............................................................. 86

Playing Loaded Style Files............................................................... 88

7

CVP-103

5

CHAPTER 6:

Registrations

Using Registrations(Registering and Recalling Panel Setups) 89

Storing a Panel Setup ...................................................................... 89

Recalling the Registered Panel Settings.......................................... 90

Protecting Panel Settings................................................................. 91

CHAPTER 7:

Song Control

Song Playback 93

Song Playback ................................................................................. 93

Part Cancel ...................................................................................... 97

Assignment of Tracks to 1/RIGHT and 2/LEFT, and Voice Assignment......

98

Overall Song Playback Volume Control ........................................... 99

Adjustment of Track Settings ......................................................... 100

Changing Settings in the MIXER Display....................................... 100

Repeat Functions ........................................................................... 101

Other Playback Controls ................................................................ 103

Playing Other Types of Music Data ............................................... 104

Guide Control 105

Guide Methods and Piano Roll ...................................................... 105

Using the Guide Function .............................................................. 106

Other Guide-related Functions....................................................... 108

Song Recording 110

Recording Setup: Disk Format ....................................................... 111

Quick Recording ............................................................................ 112

Track Recording (Multi-track Recording) ....................................... 115

Adding New Tracks ........................................................................ 118

Punch-in/out Recording ................................................................. 118

Chord Sequence 121

Other Chord Sequence Functions ................................................. 124

Other Record Edit Functions 126

Setup Memory................................................................................ 126

Song Name .................................................................................... 127

Track Edit ....................................................................................... 128

Initial Edit (Changing the Initial Data)............................................. 130

Making Settings in the INITIAL EDIT Display ................................ 131

Recording Without a Disk 133

About the CVP MEMORY Song..................................................... 133

CHAPTER 8:

The Utility Functions

Keyboard 136

FUNCTION [KEYBOARD 1] Display — page 1 ............................. 136

FUNCTION [KEYBOARD 2] Display — page 2 ............................. 137

Pedal 138

FUNCTION [PEDAL] Display — page 3 ........................................ 138

Disk 139

FUNCTION [DISK 1] Display — page 4......................................... 139

FUNCTION [DISK 2] Display — page 5......................................... 142

FUNCTION [DISK 3] Display — page 6......................................... 144

FUNCTION [DISK 4] Display — page 7......................................... 145

FUNCTION [DISK 5] Display — page 8......................................... 146

MIDI 147

FUNCTION [MIDI 1] Display — page 9 ......................................... 147

FUNCTION [MIDI 2] Display — page 10 ....................................... 148

FUNCTION [MIDI 3] Display — page 11 ....................................... 149

FUNCTION [MIDI 4] Display — page 12 ....................................... 150

Backup 152

FUNCTION [BACKUP 1] Display — page 13 ................................ 152

FUNCTION [BACKUP 2] Display — page 14 ................................ 153

Utility 154

FUNCTION [MICRO TUNING] Display — page 15 ....................... 154

FUNCTION [SCALE TUNING] Display — page 16 ....................... 155

CHAPTER 9:

Connections

Audio Connections 158

Headphones................................................................................... 158

Audio Input and Output .................................................................. 158

Data Connections 160

Connecting MIDI Equipment .......................................................... 160

Connecting to a Host Computer..................................................... 160

APPENDICES

Effect Type Lists 162

Messages 165

Troubleshooting 170

MIDI and Data Compatibility 172

Index 173

8

CVP-103

This section explains the notation conventions that are used

throughout this manual.

■ Square brackets [ ] ............................................................................................

Square brackets enclose the names of panel buttons,

sliders, and connectors as they appear on your

Clavinova. For example, the DEMO button is expressed

as [DEMO] in this manual.

■ Bold characters....................................................................................................

Bold type represents items shown in the LCD display, as well as the cor-

responding LCD buttons (i.e., the buttons directly below, or to the left or

right of, these items). For example, the phrase “Select RIGHT1 VOICE”

means that you should press the button directly below the “RIGHT1

VOICE” label at the bottom of the display.

■ Arrows in Operation Explanations..................................................

Different types of arrows are used to distinguish the steps of an operation

from its results.

Operation steps

♥ ➾ ♣ …indicates that you should do ♥, then do ♣.

Operation results

♥ ➔ ♠ …indicates that doing ♥ results in ♠.

CHAPTER 1: Getting Ready

About This Manual

6

DEMO

HELP

9

CVP-103

■ Cleaning the Disk Drive Read/Write

Head......................................................................................

● Clean the read/write head regularly. This instrument

employs a precision magnetic read/write head which,

after an extended period of use, will pick up a layer of

magnetic particles from the disks used that will even-

tually cause read and write errors.

● To maintain the disk drive in optimum working order

Yamaha recommends that you use a commercially-

available dry-type head cleaning disk to clean the

head about once a month. Ask your Yamaha dealer

about the availability of proper head-cleaning disks.

● Never open or close the key cover while a disk is

extending from the drive (i.e. in the ejected position).

The key cover may contact the disk,– possibily dam-

aging the disk or even the disk drive.

● Never insert anything but floppy disks into the disk

drive. Other objects may cause damage to the disk

drive or floppy disks.

■ About the Floppy Disks...................................

To handle floppy disks with care:

● Do not place heavy objects on a disk or bend or

apply pressure to the disk in any way. Always keep

floppy disks in their protective cases when they are

not in use.

● Do not expose the disk to direct sunlight, extremely

high or low temperatures, or excessive humidity, dust

or liquids.

● Do not open the sliding shutter and touch the ex-

posed surface of the floppy disk inside.

● Do not expose the disk to magnetic fields, such as

those produced by televisions, speakers, motors,

etc., since magnetic fields can partially or completely

erase data on the disk, rendering it unreadable.

● Never use a floppy disk with a deformed shutter or

housing.

● Do not attach anything other than the provided labels

to a floppy disk. Also make sure that labels are at-

tached in the proper location.

To protect your data (Write-protect Tab):

To prevent accidental erasure of important data, slide the

disk’s write-protect tab to the “protect” position (tab open).

Data backup

For maximum data security Yamaha

recommends that you keep two copies of

important data on separate floppy disks.

This gives you a backup if one disk is lost

or damaged. To make a backup disk use

the Disk Copy function on page 142.

■ Inserting/Ejecting Floppy Disks .............

To insert a floppy disk into the disk drive:

Hold the disk so that the label of the disk is facing

upward and the sliding shutter is facing forward, towards

the disk slot. Carefully insert the disk into the slot, slowly

pushing it all the way in until it clicks into place and the

eject button pops out.

Handling the Floppy Disk

Drive (FDD) and Floppy Disks

● Precautions

Be sure to handle floppy disks and treat the disk drive with

care. Follow the important precautions below.

● Compatible Disk Type

3.5" 2DD and 2HD type floppy disks can be used.

D

IS

K

IN

U

S

E

To eject a floppy disk:

Before ejecting the disk, be sure to confirm that the

FDD is stopped (check if the [DISK IN USE] lamp is off).

Press the eject button slowly as far as it will go; the disk

will automatically pop out. When the disk is fully ejected,

carefully remove it by hand.

D

IS

K

IN

U

S

E

DISK IN USE lamp

Never attempt to remove the disk or turn the power off

during recording, reading and playing back. Doing so can

damage the disk and possibly the disk drive.

If the eject button is pressed too quickly, or if it is not

pressed in as far as it will go, the disk may not eject prop-

erly. The eject button may become stuck in a half-pressed

position with the disk extending from the drive slot by only

a few millimeters. If this happens, do not attempt to pull

out the partially ejected disk, since using force in this

situation can damage the disk drive mechanism or the

floppy disk. To remove a partially ejected disk, try press-

ing the eject button once again, or push the disk back into

the slot and then repeat the eject procedure.

Be sure to remove the floppy disk from the disk drive

before turning off the power. A floppy disk left in the drive

for extended periods can easily pick up dust and dirt that

can cause data read and write errors.

7

10

CVP-103

■ To raise the music stand:..........................................................................

Z Pull the stand up and toward yourself as far as it will go.

X Flip down the two metal supports at the left and the right on the rear

of the music stand.

C Lower the music stand so that it rests on the metal supports.

As the illustration shows, the angle of the music stand can be set in

one of three positions, according to the position of the metal supports.

Set the left and right metal supports to the same position.

■ To lower the music stand: ........................................................................

Z Pull the music stand toward yourself as far as it will go.

X Raise the two metal supports until they are flat against the rear sur-

face of the stand.

C Gently lower the music stand backward until it is all the way down.

CAUTION

• Do not try to use the music stand in a half-raised position. Also, when lowering the

stand, let the stand all the way down before releasing it.

■ To open the key cover:.................................................................................

Z Lift the cover slightly (not too much).

X Slide the cover open.

■ To close the key cover:................................................................................

Z Slide the cover toward you.

X Gently lower the cover over the keys.

CAUTION

• Hold the cover with both hands when moving it, and do not release it until it is fully

opened or closed. Be careful to avoid catching fingers (yours or others) between the

cover and main unit.

• Do not place objects on top of the key cover. Small objects placed on the key cover

may fall inside the instrument when the cover is opened, and may be impossible to

remove. This could cause electric shock, short circuit, fire or other serious damage to

the instrument.

Be careful to avoid catching your

fingers when opening or closing

the cover.

Music Stand

Key Cover (Where Present)

Setting Up the Clavinova

8

11

CVP-103

Z Connect the power cord.

Insert the plugs at the ends of the cord, one into the AC INLET on the

bottom panel of the Clavinova, and the other into a standard AC outlet.

In some areas, a plug adapter may be provided to match the pin con-

figuration of the AC wall outlets in your area.

X Press the [POWER] switch.

The main display appears in the LCD display. (Initially, the voice

Grand Piano and the accompaniment style 8 Beat 1 are selected.)

The power lamp below the lower left end of the keyboard also lights.

C Adjust the LCD.

If the LCD is difficult to read, adjust the contrast with the [CON-

TRAST] knob at the left of the LCD.

V Adjust the volume.

Use the [MASTER VOLUME] slider to adjust the volume to an ap-

propriate level.

● When you’re ready to turn off the power, press the [POWER] switch

again. Both the LCD display and the power lamp below the left end

of the keyboard will turn off.

Connect a set of stereo headphones (optional) to the [PHONES] jack.

When headphones are connected, the internal speaker system is auto-

matically shut off. Since the Clavinova has two PHONES jacks, two sets

of headphones can be used simultaneously, allowing two people to enjoy

listening to the performance.

Standard stereo phone jacks

Your Clavinova is equipped with a variety of jacks and terminals that

let you connect it to other audio and MIDI equipment. These connectors

are located at the left end of the unit on the rear panel.

You can connect other instruments that you want to play through the

Clavinova’s speakers to the AUX IN jacks, or output the Clavinova’s

sound to external speakers using the AUX OUT jacks. Use the MIDI

terminals if you want the Clavinova to control — or be controlled by —

another MIDI instrument. There’s even a TO HOST terminal that lets

you connect the Clavinova directly to a personal computer.

Be sure to turn the power off when connecting or disconnecting other

equipment. See the instructions in Chapter 9 of this manual for details.

Turning the Power On and Off

Headphones

Other Connections

VOLUME

MASTER

VOLUME

ACMP

/

SONG

VOLUME

MAX

MIN

MAX

MIN

PHONES

THRU

OUT

IN

MIDI

HOST SELECT

MIDI

Mac

PC

-

1

PC

-

2

TO HOSTPEDAL

AUX I N

RR

AUX O UT

L/L

+

RL/L

+

R

Setting Up the Clavinova

9

POWER

CONTRAST

12

CVP-103

C1 D1 E1 F1 G1 A1 B1 C2 D2 E2 F2 G2 A2 B2 C3 D3 E3

B0A0G0F0E0D0C0B-1A-1

VOLUME

MASTER

VOLUME

ACMP

/

SONG

VOLUME

MAX

MIN

MAX

MIN

DEMO

HELP

8BEAT

SWING/

JAZZ

BALL-

ROOM

TRAD/

WALZ

LATIN

COUNTRY

16BEAT DANCE

ROCK/

R&B

PIANIST

BALLAD

MUSIC

DATABASE

HARMONYDISK

CUSTOM

STYLE

START

/

STOP

TAP SYNCHRO START

/

STOP

CONTRAST

BEAT

DIRECT ACCESS

PAG E

MIXER

FUNCTION

AUTO ACCOMPA NIMENT

MAIN A

MAIN B

MAIN C

MAIN D

ENDING

FA DE

IN

/

OUT

AUTO FILL

INTRO

CVP-103

METRONOME RESET

TEMPO

ACMP ON

ANCEL

21

3

5

6

*

&

w

i

e

r t

8

7

4

9

0 ! @ # $ % ^ ( ) q

y

u o

Panel Controls and Terminals

Volume Section

1 [MASTER VOLUME] ....................................page 23

2 [ACMP/SONG VOLUME ] ............................page 23

Special Mode Control Section

3 [DEMO] .........................................................page 14

4 [HELP] ..........................................................page 27

Accompaniment Style Section

5 STYLE buttons .............................................page 49

6 [DISK/CUSTOM]...........................................page 73

7 [MUSIC DATABASE] ....................................page 67

8 [HARMONY] .................................................page 69

Auto Accompaniment Section

9 [ACMP ON]...................................................page 57

0 [INTRO].........................................................page 54

! [MAIN A] .......................................................page 51

@ [MAIN B] .......................................................page 51

# [MAIN C] .......................................................page 51

$ [MAIN D] .......................................................page 51

% [ENDING]......................................................page 55

^ [FADE IN/OUT] .....................................pages 55, 56

Metronome Section

& [METRONOME]............................................page 25

* TEMPO [–], [+] .............................................page 25

Start/Stop Section

( [TAP] .............................................................page 53

) [SYNCHRO]..................................................page 53

q [START/STOP]......................................pages 52, 55

Display Control Section

w [CONTRAST]................................................ page 11

e [BEAT] lamps................................................page 52

r [FUNCTION] ...............................................page 136

t[MIXER] .........................................................page 24

y LCD display ..................................................page 16

u PAGE [<], [>] ..............................................page 19

i [DIRECT ACCESS] ......................................page 21

o LCD buttons..................................................page 18

p [EXIT]............................................................page 21

Q Data dial .......................................................page 17

W [–], [+]............................................................page 17

Song Control Section

E [SONG] .........................................................page 94

R [PLAY/STOP]................................................page 95

T [REC] ..........................................................page 113

Y [PAUSE]......................................................page 103

U [REW] .........................................................page 103

I [FF] .............................................................page 103

10

THRU

OUT

IN

MIDI

HOST SELECT

MIDI

Mac

PC

-

1

PC

-

2

TO HOSTPEDAL

AUX IN

RR

AUX OUT

L/L

+

RL/L

+

R

J K

L

: z

x

PHONES

H

13

CVP-103

Panel Controls and Terminals

Guide Control Section

O [EASY PLAY] ..............................................page 105

P [NEXT NOTE] .............................................page 105

a [SOUND REPEAT] .....................................page 106

Voice Section

s VOICE buttons .............................................page 29

d [DUAL] ..........................................................page 33

f [SPLIT]..........................................................page 36

g [REVERB] .....................................................page 41

h [EFFECT]......................................................page 46

Registration/One Touch Setting Section

j [1] through [4] .......................................pages 72, 90

k [BANK –] .......................................................page 89

l [BANK +].......................................................page 89

; [REGISTRATION].........................................page 90

A [ONE TOUCH SETTING] .............................page 72

S [DISK IN USE] lamp .......................................page 9

D Floppy disk drive (3.5”) ..................................page 9

F [POWER] ......................................................page 11

G Keyboard guide lamps ...............................page 109

Connectors

H [PHONES]...................................................page 158

J AUX IN [L/L+R], [R]....................................page 158

K AUX OUT [L/L+R], [R]................................page 159

L [PEDAL] .............. page 42 in the Reference Booklet

: MIDI [IN], [OUT], [THRU] ...........................page 160

z [HOST SELECT] ........................................page 160

x [TO HOST]..................................................page 160

Pedals

c Soft pedal .....................................................page 40

v Sostenuto pedal ...........................................page 40

b Damper pedal...............................................page 40

F3 G3 A3 B3 C4 D4 E4 F4 G4 A4 B4 C5 D5 E5 F5 G5 A5 B5 C6

D6 E6 F6 G6 A6 B6 C7

EXIT

SONG

PAUSE REW FF

REC

PL AY/

STOP

SONG CONTROL

GUIDE CONT ROL

EA SY PL AY

NEXT NOTE

SOUND

REPEAT

POWER

PIANO E. PIANO GUITAR

ORGAN

SYNTHE-

SIZER

STRINGS/

CHOIR

VOICE

XG

ENSEMBLE

BASS

BRASS

SAX

/

FLUTE

PER-

CUSSION

DUAL

SPLIT

REVERB

EFFECT

DISK IN USE

1

234

BANK

REGISTRATION/ONE TOUCH SETTING

ONE TOUCH

SETTING

REGIST-

RATION

p W

O P a j k l ;

s

d

A

g

S

F

D

f h

Q

E

Y

U

R

T

I

G

11

c

v

b

14

CVP-103

The Clavinova features a total of 50 demo songs: 4 feature songs,

24 special pieces showcasing the voices, and 22 pieces showcasing

the styles. Listen to them all and hear what the Clavinova can do.

X Select the desired play mode.............................................................

Select the desired play mode by pressing the rightmost LCD button. The

following three modes are available:

ALL All the songs play back continuously in order, starting from the

selected song. Playback continues repeatedly until stopped.

RANDOM All the songs play back randomly, starting from the selected

song. Playback continues repeatedly until stopped.

SINGLE Only the selected song plays back. When the song is finished,

playback stops automatically.

Z Call up the Demo Play mode...............................................................

Press [DEMO]. The lamps of the STYLE button and VOICE button

flash continuously, and the DEMO display appears.

C Select the song and start playback..............................................

When you select a song, the demo automatically starts playing in the

selected play mode. There are three ways to select a demo song, as de-

scribed below:

• You can also start the demo playback,

beginning with the first feature song, by

pressing [START/STOP] or [PLAY/

STOP].

• For a complete list of the Clavinova’s

demo songs, refer to page 9 of the

Reference Booklet.

(A) To listen to one of the featured demo songs, press one of

the buttons under the numbers 1 through 4 in the display.

➔ The current song number is highlighted during playback.

Playing the Demo Songs

12

DEMO

HELP

15

CVP-103

(B) To listen to a voice demo, press the VOICE button corre-

sponding to the desired voice category.

➔ Playback starts from the first demo song for the selected category.

The lamp of the corresponding VOICE button flashes.

There are two demo songs for each voice

category. To skip to the second song,

press the flashing button a second time.

(C) To listen to a style demo, press the STYLE button corre-

sponding to the desired style category.

➔ Playback starts from the first demo song for the selected category.

The lamp of the corresponding STYLE button flashes.

There are two demo songs for each style

category. To skip to the second song,

press the flashing button a second time.

V Adjust the volume...........................................................................................

Use the [MASTER VOLUME] slider to adjust the volume.

The [ACMP/SONG VOLUME] control

cannot be used.

B Stop the demo playback. .........................................................................

To change songs during playback:

Press the LCD button, VOICE button, or

STYLE button of another song; the song

then changes. When ALL or RANDOM is

selected as the play mode, the Clavinova

will play other songs when the selected

song is finished.

To stop playback, press either [START/STOP] or [PLAY/STOP], or

the LCD button corresponding to the song that’s currently playing.

N Exit the Demo mode......................................................................................

To exit the Demo mode, press [DEMO] again (or press [EXIT]).

● Playing Along with the Demo Songs

You can play the keyboard while a demo song is playing back. You

can also change the tempo (page 25) and use the [REW], [FF] and

[PAUSE] buttons. When you play 3. Lyric Demo, the Clavinova will

display the lyrics so you can sing (as well as play) along. Also, you can

use the Guide function (page 105) while the Clavinova is playing 4.

GUIDE Demo. You cannot change the voice selection while the demo

is playing, however.

Demo song data is not output through

the [MIDI OUT] terminal; however, your

keyboard performance data is output.

Playing the Demo Songs

13

PIANO E. PIANO GUITAR

ORGAN

SYNTHE-

SIZER

STRINGS/

CHOIR

VOICE

XG

ENSEMBLE

BASS

BRASS

SAX

/

FLUTE

PER-

CUSSION

DUAL

SPL I T

REVERB

EFFECT

8BEAT

SWING/

JAZZ

BALL-

ROOM

TRAD/

WALZ

LATIN

COUNTRY

16BEAT DANCE

ROCK/

R&B

PIANIST

BALLAD

MUSIC

DATABASE

HARMONYDISK

CUSTOM

STYLE

16

CVP-103

You will refer to the LCD display frequently as you operate your

Clavinova. This section consists of a short tutorial that will help

you learn how to read the LCD display and use the related

controls.

Many of the Clavinova’s functions are displayed at the bottom of the

LCD. The main display shown below contains two functions: KBD VOL

and RIGHT1 VOICE. These items are displayed in rounded rectangles,

which means they represent settings that can be changed.

Selecting a Function

Main display

Remember, the

main display

is the dis-

play that appears first when you turn the

power on.

Before you can change a function’s setting, however, you have to select it

first. In the main display, the RIGHT1 VOICE function is highlighted, indi-

cating that this function is currently selected.

Highlighted items

Selected items are

highlighted

(i.e., white

letters on a dark background).

To select a function, press and quickly release the LCD button directly

below that function. For example, you can select KBD VOL by pressing the

leftmost LCD button.

LCD buttons

The five LCD buttons under the LCD

display represent different functions,

depending on the contents of the display.

CHAPTER 2: Basic Operation

Using the LCD Display Controls

14

Press to select.

17

CVP-103

There are several ways to change a function’s value. Here are two of the

main ways:

■ Using the data dial or [–] and [+] buttons.................................

Once you have selected a function, you can change its setting with the

data dial or the [–] and [+] buttons. Since you have just selected KBD

VOL, try turning the dial or pressing the [–] button until it reads 0.

Changing a Setting

You can press the [–] and [+] buttons

repeatedly to change the value a little, or

hold them down to change it quickly.

The KBD VOL function sets the keyboard volume. When you set it to

0, you will find that the keyboard won’t produce any sound, no matter

how high you set the [MASTER VOLUME] slider!

Refer to page 23 for details on the KBD

VOL function.

■ Using the LCD buttons..................................................................................

You can also increase a setting by simply pressing and holding the

corresponding LCD button. For now, since you’ll want to hear your key-

board later on, press and hold the leftmost LCD button until the value for

KBD VOL is back up to 127.

This is why you should release the LCD

button quickly when you select a func-

tion: you could end up raising its value

when you want to lower it!

Once you’ve got the keyboard volume back where it belongs, you can

learn about a couple of other ways to change settings.

Hold down to increase.

Using the LCD Display Controls

15

18

CVP-103

You can use either of the methods described previously to change the current voice

selection. Just press RIGHT1 VOICE and hold the button down, or use the data dial or

the [+] button to scan through the options. Try listening to a few of the voices while

you’re at it…

Changing a Setting in a Menu Display

Voice

A voice is one of the sounds

the Clavinova uses to make

music.

The problem with this method is that it can be hard to find the voice you’re looking

for — after all, the Clavinova has more than 600 voices! So you’ll probably want to use

a menu display to see what your choices are. Try pressing the [PIANO] button now.

When you press one of the VOICE buttons, the LCD displays a new set of

functions listing the voices of that type. You should now be looking at a menu of

piano voices.

■ Using the LCD buttons.................................................................................................

Each piano voice in this display is listed as a separate function in a rounded rectan-

gle. This means that you can use the LCD buttons to select voices, just like you did to

select the KBD VOL and RIGHT1 VOICE functions at the beginning of this tutorial.

Menu displays

You will use menu displays for

only two purposes: to select a

voice, as shown here, or to

select an accompaniment style

(page 49).

Keep in mind that you can use the data dial or [–] and [+] buttons to select

functions only when viewing a menu display. In other displays, these controls

will change the value of the currently selected function instead.

Try selecting different piano voices in this display before you move on to the

next step.

Using the LCD Display Controls

Refer to page 29 for more

details about selecting voices.

Use the data dial or

[–] and [+] buttons to

select a voice.

16

PIANO E. PIANO GUITAR

SYNTHE-

SIZER

■ Using the data dial or [–] and [+] buttons................................................

There is another way to select voices in this display. You can use the data dial

or the [–] and [+] buttons to change the selection. Press [–] or turn the data dial

counterclockwise to select a voice to the left; press [+] or turn the dial clockwise

to select a voice to the right.

Press an LCD button to select the corresponding voice.

19

CVP-103

Using the LCD Display Controls

17

As you were trying out the piano voices in the preceding step, you

may have been surprised to see all the voice names suddenly replaced by

an entirely different set of voices. Specifically, this occurs when you

select the rightmost voice in the display (Midi Grand), then turn the

data dial clockwise or press the [+] button.

Displaying a Different Page

Display pages

Some displays are divided into two or

more pages, indicated by a series of

overlapping boxes in the upper right

corner of the display. The number in the

topmost box is the number of the current

display page.

This happens because the CVP-103 has more piano voices than it can

fit in the display. When one of the Clavinova’s features includes more

functions than will fit in the display, the functions are divided among two

or more display pages. The VOICE SELECT Piano display consists of

two display pages, as shown below:

When a display is divided into pages, you can use PAGE buttons to

change pages. Try it: press the [<] button to see page 1, or the [>] but-

ton to see page 2. Once you have displayed the desired page, you can use

the LCD buttons select a voice in that page as described in the preceding

step.

Refer to page 138 for details about the

functions on the FUNCTION [PEDAL]

display page.

PAG E

Use the PAGE buttons to switch between pages.

After you have changed a function’s value, you may find you want to

restore its basic setting. To demonstrate this, we’ll have to look at another of

the Clavinova’s displays. Press the [FUNCTION] button.

Resetting a Function’s Value

Basic settings

• The functions of the Clavinova are set

to certain standard values or standard

conditions when the instrument is

shipped. These settings and conditions

are called the basic settings.

• A function’s basic settings are gener-

ally noted in the sidebar together with

the possible settings for that function.

• You can also use the Recall function

(page 153) to restore basic settings at

any time.

This button calls up one of the Clavinova’s FUNCTION displays. You

can use this display to tune and transpose the keyboard.

Refer to page 136 for details on the

TUNE and TRANSPOSE functions.

The TUNE function in this display corresponds to two LCD buttons

labeled ▼ and ▲. You can use these buttons to tune the keyboard up or

down. Press and hold the ▼ button (or use the data dial or the [–] button)

to tune the keyboard down as far as it will go.

MIXER

FUNCTION

20

CVP-103

If you look at the upper right corner of the LCD, you’ll notice that the

FUNCTION display consists of several display pages. Press the PAGE [>]

key once to open the next page, which is titled FUNCTION [KEYBOARD

2]. We’ll use the functions on this page to discuss the next operation.

In addition to the FIXED VELOCITY function, which is selected in this

display, the FUNCTION [KEYBOARD 2] page has two functions in normal

rectangles: KEY TOUCH and VOICE SETTING. Such functions cannot be

selected; instead, pressing the corresponding LCD button changes the setting

directly without selecting the function.

Using Functions in Non-rounded Rectangles

Using the LCD Display Controls

The FIXED VELOCITY function is de-

scribed on page 137.

18

If you play a few notes, you’ll notice that your Clavinova is flat by quite

a bit. Now, let’s assume that you want to reset the keyboard to the standard

440.0 Hz. You could use the ▲ button (or the data dial, or the [

+

] button) to

return the value to its basic setting — but there’s an easier way:

When a function has a basic setting, you can reset it to that value by

pressing both the ▲ and ▼ buttons (or both the [–] and [+] buttons) simul-

taneously. Try doing this now.

There are some functions whose settings

cannot be returned to the basic value by

pressing the

▲

and

▼

buttons (or [–] and

[+] buttons) simultaneously.

When you’ve got the keyboard back in tune, you’re ready to go on to the

next operation.

La pagina sta caricando ...

Yamaha CVP-103 Manuale utente

Yamaha CVP-103 Manuale utente

in altre lingue

Documenti correlati