Indesit BWA 91082X W EU Guida utente

Categoria
Lavatrici
Tipo
Guida utente
GB
1
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 4
Cutting off the water or electricity supply
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and tips, 5
General safety
Load balancing system
Disposal
Description of the washing machine
and starting a wash cycle, 6-7
Control panel
Indicator lights
Starting a wash cycle
Wash cycles, 8
Push & Wash
Table of wash cycles
Personalisation, 9
Setting the temperature
Setting the spin speed
Functions
Detergents and laundry, 10
Detergent dispenser drawer
Preparing the laundry
Garments requiring special care
Troubleshooting, 11
Service, 12
BWA 91082
Instructions for use
WASHING MACHINE
English,1
GB
IT
Italiano,13
2
GB
Levelling the machine correctly will provide
it with stability, help to avoid vibrations and
excessive noise and prevent it from shifting
while it is operating. If it is placed on carpet or
a rug, adjust the feet in such a way as to allow
a sufficient ventilation space underneath the
washing machine.
Connecting the electricity and water
supplies
Connecting the water inlet hose
1. Connect the inlet
hose by screwing it
to a cold water tap
using a 3/4 gas thre-
aded connection (see
figure).
Before performing the
connection, allow the
water to run freely un-
til it is perfectly clear.
2. Connect the inlet
hose to the washing
machine by screwing
it onto the correspon-
ding water inlet of the
appliance, which is
situated on the top
right-hand side of the
rear part of the ap-
pliance (see figure).
3. Make sure that the hose is not folded over
or bent.
! The water pressure at the tap must fall within
the range of values indicated in the Technical
data table (see next page).
! If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
Installation
! This instruction manual should be kept in a
safe place for future reference. If the washing
machine is sold, transferred or moved, make
sure that the instruction manual remains with
the machine so that the new owner is able to
familiarise himself/herself with its operation
and features.
! Read these instructions carefully: they con-
tain vital information relating to the safe instal-
lation and operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its
packaging.
2. Make sure that the washing machine has
not been damaged during the transportation
process. If it has been damaged, contact the
retailer and do not proceed any further with
the installation process.
3. Remove the 4 pro-
tective screws (used
during transportation)
and the rubber wa-
sher with the cor-
responding spacer,
located on the rear
part of the appliance
(see figure).
4. Close off the holes using the plastic plugs
provided.
5. Keep all the parts in a safe place: you will
need them again if the washing machine ne-
eds to be moved to another location.
! Packaging materials should not be used as
toys for children.
Levelling
1. Install the washing machine on a flat sturdy
floor, without resting it up against walls, furni-
ture cabinets or anything else.
2. If the floor is not
perfectly level, com-
pensate for any une-
venness by tightening
or loosening the
adjustable front feet
(see figure); the angle
of inclination, measu-
red in relation to the
worktop, must not
exceed 2°.
GB
3
Connecting the drain hose
Connect the drain
hose, without bending
it, to a drain duct or
a wall drain situated
between 65 and 100
cm from the floor;
alternatively, placed
it over the edge of a
basin, sink or tub, fa-
stening the duct sup-
plied to the tap (see
figure). The free end
of the hose should
not be underwater.
! We advise against the use of hose extensions;
if it is absolutely necessary, the extension must
have the same diameter as the original hose
and must not exceed 150 cm in length.
Electrical connections
Before plugging the appliance into the electri-
city socket, make sure that:
• thesocketisearthedandcomplieswithall
applicable laws;
• thesocketisabletowithstandthemaximum
power load of the appliance as indicated in the
Technical data table (see opposite);
• thepowersupplyvoltagefallswithintheva-
lues indicated in the Technical data table (see
opposite);
• thesocketiscompatiblewiththeplugofthe
washing machine. If this is not the case, repla-
ce the socket or the plug.
! The washing machine must not be installed
outdoors, even in covered areas. It is extremely
dangerous to leave the appliance exposed to
rain, storms and other weather conditions.
! When the washing machine has been instal-
led, the electricity socket must remain within
easy reach.
65 - 100 cm
! Do not use extension cords or multiple sockets.
! The cable should not be bent or compressed.
! The power supply cable must only be repla-
ced by authorised technicians.
Warning! The company shall not be held re-
sponsible in the event that these standards are
not observed.
The first wash cycle
Once the appliance has been installed, and
before you use it for the first time, run a wash
cycle with detergent and no laundry, using the
wash cycle “Auto Clean” (see “Cleaning the
washing machine”).
Technical data
Model
BWA 91082
Dimensions
width 59.5 cm
height 85 cm
depth 60.5 cm
Capacity
from 1 to 9 kg
Electrical
connections
please refer to the technical
data plate fixed to the ma-
chine
Water
connections
maximum pressure
1 MPa (10 bar)
minimum pressure
0.05 MPa (0.5 bar)
drum capacity 62 litres
Spin speed
up to 1000 rotations per minute
Test wash
cycles in
accordance
with re-
gulations
1061/2010
and
1015/2010.
Programme 9:
Eco Cotton 60°.
Programme 9:
Eco Cotton 40°.
This appliance conforms to
the following EC Directives:
- 2004/108/EC (Electroma-
gnetic Compatibility)
- 2006/95/EC (Low Voltage)
- 2012/19/EU (WEEE)
4
GB
Care and maintenance
Cleaning the pump
The washing machine is fitted with a self-
cleaning pump which does not require any
maintenance. Sometimes, small items (such
as coins or buttons) may fall into the protective
pre-chamber at the base of the pump.
! Make sure the wash cycle has finished and
unplug the appliance.
To access the pre-chamber:
1. Take off the cover
panel on the front of
the machine by first
pressing it in the cen-
tre and then pushing
downwards on both
sides until you can re-
move it (see figures).
2. Unscrew the lid
by rotating it anti-
clockwise (see figu-
re): a little water may
trickle out. This is
perfectly normal.
3. Clean the inside thoroughly.
4. Screw the lid back on.
5. Reposition the panel, making sure the hooks
are securely in place before you push it onto
the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If
there are any cracks, it should be replaced
immediately: during the wash cycles, water
pressure is very strong and a cracked hose
could easily split open.
! Never use second-hand hoses.
Cutting off the water and electricity
supplies
•Turnoffthewatertapaftereverywashcycle.
This will limit wear on the hydraulic system inside
the washing machine and help to prevent leaks.
•Unplugthewashingmachinewhencleaningit
and during all maintenance work.
Cleaning the washing machine
•Theouterpartsandrubbercomponents
of the appliance can be cleaned using a soft
cloth soaked in lukewarm soapy water. Do not
use solvents or abrasives.
•Thewashingmachinehasa“AutoClean”
programme for its internal parts that must be
run with no load in the drum.
For maximum performance you may want
to use either the detergent (i.e. a quantity
10% the quantity specified for lightly-soiled
garments) or special additives to clean the
washing machine. We recommend running a
cleaning programme every 40 wash cycles.
To start the programme press buttons A and
B simultaneously for 5 seconds (see figure).
The programme will start automatically and
will last approximately 70 minutes. To stop the
cycle press the START/PAUSE button.
Cleaning the detergent dispenser
drawer
To remove the drawer,
press lever (1) and pull
the drawer outwards (2)
(see figure).
Wash it under running
water; this procedure
should be repeated fre-
quently.
Caring for the door and drum of your
appliance
•Alwaysleavetheportholedoorajarinorderto
prevent unpleasant odours from forming.
2
1
1
2
3
A
B
GB
5
Precautions and tips
! This washing machine was designed and constructed in
accordance with international safety regulations. The fol-
lowing information is provided for safety reasons and must
therefore be read carefully.
General safety
•Thisappliancewasdesignedfordomesticuseonly.
This appliance can be used by children aged
from 8 years and above and persons with re-
duced physical, sensory or mental capabilities
or lack of experience and knowledge if they
have been given supervision or instruction
concerning use of the appliance in a safe way
and understand the hazards involved. Children
shall not play with the appliance. Cleaning and
user maintenance shall not be made by children
without supervision.
•Thewashingmachinemustonlybeusedbyadults,inaccor-
dance with the instructions provided in this manual.
•Donottouchthemachinewhenbarefootorwithwetor
damp hands or feet.
•Donotpullonthepowersupplycablewhenunplugging
the appliance from the electricity socket. Hold the plug
and pull.
•Donotopenthedetergentdispenserdrawerwhilethe
machine is in operation.
•Donottouchthedrainedwaterasitmayreachextreme-
ly high temperatures.
•Neverforcetheportholedoor.Thiscoulddamagethesafety
lock mechanism designed to prevent accidental opening.
•Iftheappliancebreaksdown,donotunderanycircum-
stances access the internal mechanisms in an attempt
to repair it yourself.
•Alwayskeepchildrenwellawayfromtheappliancewhile
it is operating.
•Thedoorcanbecomequitehotduringthewashcycle.
•Iftheappliancehastobemoved,workinagroupoftwo
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.
•Beforeloadinglaundryintothewashingmachine,make
sure the drum is empty.
Load balancing system
Before every spin cycle, to avoid excessive vibrations and
to distribute the load in a uniform manner, the drum rotates
continuously at a speed which is slightly greater than the
washing rotation speed. If, after several attempts, the load is
not balanced correctly, the machine spins at a reduced spin
speed. If the load is excessively unbalanced, the washing ma-
chine performs the distribution process instead of spinning.
To encourage improved load distribution and balance, we
recommend small and large garments are mixed in the load.
Disposal
•Disposingofthepackagingmaterials:observelocal
regulations so that the packaging may be re-used.
• TheEuropeanDirective2012/19/EU-WEEEonWaste
Electrical and Electronic Equipment, requires that
old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected
separately in order to optimise the recovery and
recycling of the materials they contain and reduce
the impact on human health and the environment.
The crossed out “wheeled bin” symbol on the
product reminds you of your obligation, that when
you dispose of the appliance it must be separately
collected.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
6
GB
Detergent dispenser drawer: used to dispense deter-
gents and washing additives (see “Detergents and laundry”).
ON/OFF button: switches the washing machine on and off.
PUSH & WASH button: (see “Wash cycles”).
WASH CYCLE knob: programmes the wash cycles. During
the wash cycle, the knob does not move.
FUNCTION buttons with indicator light: used to select the
available functions. The indicator light corresponding to the
selected function will remain lit.
CHILD LOCK button with indicator light: to activate the
control panel lock, press and hold the button for approximately
2 seconds. When the symbol is illuminated, the control
panel is locked (apart from the ON/OFF button). This means
it is possible to prevent wash cycles from being modified
accidentally, especially where there are children in the home.
To deactivate the control panel lock, press and hold the button
for approximately 2 seconds.
TEMPERATURE button: sets the temperature or the cold
wash cycle (see “Personalisation”).
SPIN button: sets the spin speed or exclude the spin cycle
completely (see “Personalisation”).
DELAY TIMER button: delays the start of the wash cycle
by up to 9 hours.
Press the button repeatedly until the indicator light corre-
sponding to the desired delay time turns on.
When the button is pressed for the fourth time, the option
will be deactivated.
N.B.: once the START/PAUSE button has been pressed, the
delay time can only be modified by decreasing it until the set
programme is launched.
! This option is available on all programmes.
WASH CYCLE PROGRESS
indicator light
s: used to mo-
nitor the progress of the wash cycle.
The illuminated indicator light shows which phase is in pro-
gress.
DOOR LOCKED indicator light: indicates whether the door
may be opened or not (see next page).
START/PAUSE button with indicator light: starts or tempo-
rarily interrupts the wash cycles.
N.B. To pause the wash cycle in progress, press this button;
the corresponding indicator light will flash orange, while the
indicator light for the current wash cycle phase will remain lit
in a fixed manner. If the DOOR LOCKED indicator light is
switched off, the door may be opened (wait approximately
3 minutes).
To start the wash cycle from the point at which it was inter-
rupted, press this button again.
Standby mode
This washing machine, in compliance with new energy saving
regulations, is fitted with an automatic standby system which
is enabled after about 30 minutes if no activity is detected.
Press the ON-OFF button briefly and wait for the machine
to start up again.
Description of the washing
machine and starting a wash cycle
Control panel
WASH CYCLE PROGRESS
indicator lights
DOOR
LOCKED
indicator light
START/PAUSE
button with indicator
light
Detergent dispenser drawer
ON/OFF
button
WASH CYCLE
knob
DELAY TIMER
button
TEMPERATURE
button
SPIN
button
FUNCTION
buttons with
indicator lights
PUSH & WASH
button
CHILD LOCK
button with
indicator light
GB
7
Indicator lights
The indicator lights provide important information.
This is what they can tell you:
Delayed start
If the DELAY TIMER function has been activated (see “Per-
sonalisation”), after the wash cycle has been started the
indicator light corresponding to the selected delay period
will begin to flash:
As time passes, the remaining delay will be displayed and
the corresponding indicator light will flash:
The set programme will start once the selected time delay
has expired.
Wash cycle phase indicator lights
Once the desired wash cycle has been selected and has be-
gun, the indicator lights switch on one by one to indicate which
phase of the cycle is currently in progress.
Function buttons and corresponding indicator lights
When a function is selected, the corresponding indicator
light will illuminate.
If the selected function is not compatible with the program-
med wash cycle, the corresponding indicator light will flash
and the function will not be activated.
If the selected option is not compatible with another
previously selected option, the indicator light will flash
accompanied by a buzzer (3 beeps), and only the latter
option will be activated; the indicator light corresponding to
the activated option will turn on
Door locked indicator light
When the indicator light is on, the porthole door is locked
to prevent it from being opened; make sure the indicator
light is off before opening the door (wait approximately 3
minutes).
To open the door during a running wash cycle, press the
START/PAUSE button; the door may be opened once the
DOOR LOCKED indicator light turns off.
Starting a wash cycle
Rapid programming
1. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed
the maximum load value indicated in the table of
programmes and wash cycles on the following page.
2. ADD THE DETERGENT. Pull out the detergent
dispenser drawer and pour the detergent into the
relevant compartments as described in “Detergents and
laundry”.
3. CLOSE THE DOOR.
4. Press the “PUSH & WASH” button to start the wash
programme.
Traditional programming
1. Turn the washing machine on by pressing the ON/OFF
button. All the indicator lights will turn on for a few secon-
ds, then only the indicator lights relative to the selected
programme settings will remain lit and the START/PAUSE
indicator light will flash.
2. Load the laundry and close the door.
3. Set the WASH CYCLE knob to the desired programme.
4. Set the washing temperature (see “Personalisation”).
5. Set the spin speed (see “Personalisation”).
6. Measure out the detergent and washing additives (see
“Detergents and laundry”).
7. Select the desired functions.
8. Start the wash cycle by pressing the START/PAUSE
button and the corresponding indicator light will remain lit
in a fixed manner in green. To cancel the set wash cycle,
pause the machine by pressing the START/PAUSE button
and select a new cycle.
9. At the end of the wash cycle the indicator light will
switch on. The door can be opened once the DOOR
LOCK indicator light turns off (wait approximately 3 mi-
nutes). Take out your laundry and leave the appliance door
ajar to make sure the drum dries completely. Switch the
washing machine off by pressing the ON/OFF button.
Wash
Rinse
Spin
Drain
End of wash cycle
8
GB
Wash cycles
Table of wash cycles
Push & Wash
This function allows for starting a wash cycle even when the machine is switched off without having to press the ON/OFF
button in advance, or after switching on the machine, without having activated any button and/or selector (otherwise, the
Push & Wash function will be deactivated). To start the Push & Wash cycle press and hold the relative button for 2 seconds.
The lit indicator light indicates that the cycle has started. This wash cycle is ideal for cotton or synthetic fabrics, as it washes
at a temperature of 30° and a maximum spin speed of 1000 rpm. Maximum load 4 kg. (Cycle duration 45’).
How does it work?
1. Load the laundry (cotton and/or synthetic garments) and close the door.
2. Pour the detergent and additives.
3. Start the programme by pressing and holding the Push & Wash button for 2 seconds. The relative indicator light turns
green and the door will lock (the DOOR LOCKED symbol turns on).
N.B.: starting the wash cycle through the Push & Wash button activates an automatic non-customisable cycle
recommended for cotton and synthetic fabrics. This programme does not allow for setting any additional options.
To open the door while an automatic cycle is under way, press the START/PAUSE button; if the DOOR LOCKED symbol
is switched off the door may be opened. Press the START/PAUSE button again to restart the wash cycle from the point at
which it was interrupted.
4. Once the programme is finished, the indicator light turns on.
1) Test wash cycle in compliance with regulation 1061/2010: set wash cycle 9 with a temperature of 60°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should
be used for garments which can be washed at 60°C. The actual washing temperature may differ from the indicated value.
2) Test wash cycle in compliance with regulation 1061/2010: set wash cycle 9 with a temperature of 40°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should
be used for garments which can be washed at 40°C. The actual washing temperature may differ from the indicated value.
For all Test Institutes:
3) Long wash cycle for cottons: set wash cycle 6 with a temperature of 40°C.
4) Synthetic program along: set wash cycle 7 with a temperature of 40°C.
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-
ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
* If you select programme and exclude the spin cycle, the machine will drain only.
Wash cycles
Description of the wash cycle
Max.
temp.
C)
Max.
speed
(rpm)
Detergents
Max. load (kg)
Residual
dampness %
Energy
consumption kWh
Total water lt
Cycle duration
Wash
Fabric
softener
Everyday 30° ECO
1
Daily cotton
30° 1000
4.5 - - - 100’
2
Daily synthetics
30° 1000
4.5 - - - 90’
3
Coloureds
30° 1000
4.5 - - - 95’
4
Delicates
30° 0
1 - - - 80’
5
Rapid 30min: to refresh lightly soiled garments quickly (not suitable for wool,
silk and clothes which require washing by hand).
30° 800
4.5 70 0.18 42 30’
Traditionals
6
Cotton (3): lightly soiled whites and delicate colours.
40°
(Max.60°)
1000
9 62 1.10 97 225’
7
Synthetics (4): lightly soiled resistant colours.
40°
(Max.60°)
1000
4.5 46 0.74 59 125’
8
Mixed
40° 1000
9 - - - 105’
9
Eco cotton 60°C (1): heavily soiled whites and resistant colours.
60° 1000
9 62 1.30 57.4 240’
9
Eco cotton 40°C (2): lightly soiled whites and delicate colours.
40° 1000
9 62 1.10 97 225’
10
White cotton: heavily soiled whites and resistant colours.
60°
(Max.90°)
1000
9 - - - 200’
Specials
11
Sport
30° 600
4 - - - 60’
12
Duvet: for down-stuffed garments. 30° 1000
3.5 - - - 115’
13
Wool: for wool, cashmere, etc. 40° 800
2 - - - 85’
14
Anti odour
40° 1000
3.5 - - - 105’
Rinse + Spin - 1000
-
9 - - - 55’
Spin + Drain - 1000
- -
9 - - - 10’
Drain only * -
- -
9 - - - 3’
GB
9
Setting the temperature
Press the TEMPERATURE button to set the wash temperature (see Table of wash cycles).
The temperature may be lowered, or even set to a cold wash (20°). The washing machine will automatically prevent you from
selecting a temperature which is higher than the maximum value set for each wash cycle.
! Exception: if the 6 programme is selected, the temperature can be increased up to a value of 60°C.
! Exception: if the 7 programme is selected, the temperature can be increased up to a value of 60°C.
! Exception: if the 10 programme is selected, the temperature can be increased up to a value of 90°C.
Setting the spin speed
Press the SPIN SPEED button to set the spin speed for the selected wash cycle.
The maximum spin speeds available for each wash cycle are as follows:
Wash cycles Maximum spin speed
Cottons 1000 rpm
Synthetics 1000 rpm
Wool 800 rpm
The spin speed may be lowered, or the spin cycle can be excluded altogether by selecting the symbol .
The washing machine will automatically prevent you from selecting a spin speed which is higher than the maximum speed
set for each wash cycle.
Functions
The various wash functions available with this washing machine will help to achieve the desired results, every time.
To activate the functions:
1. Press the button corresponding to the desired function;
2. the function is enabled when the corresponding indicator light is illuminated.
Note:
- If the selected function is not compatible with the programmed wash cycle, the corresponding indicator light will flash and
the function will not be activated.
- If the selected option is not compatible with another previously selected option, the indicator light will flash accompanied
by a buzzer (3 beeps), and only the latter option will be activated; the indicator light corresponding to the activated option
will turn on.
Stain removal
Thisoptionallowsforselectingthetypeofdirtsoastooptimallyadjustthecycleforremovingthestains.Thefollowingtypes
of dirt can be selected:
- Food, for stains caused by foodstuffs and beverages, for example.
- Work, for grease and ink stains, for example.
- Outdoor, for mud and grass stains, for example.
! The wash cycle duration varies according to the type of selected dirt.
Extra Rinse
By selecting this option, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is particularly
useful for sensitive skin.
Easy iron
By selecting this function, the wash and spin cycles will be modified in order to reduce the formation of creases. At the end
of the cycle the washing machine will perform slow rotations of the drum, while the EASY IRON and START/PAUSE indicator
lights will flash and the led will remain lit in a fixed manner. To end the cycle, press the START/PAUSE button or the EASY
IRON button.
Personalisation
10
GB
Detergents and laundry
Detergent dispenser drawer
Successful washing results also depend on the correct
dose of detergent: adding too much detergent will not
necessarily result in a more efficient wash, and may in fact
cause build up on the inside of your appliance and contri-
bute to environmental pollution.
! Do not use hand washing detergents because these
create too much foam.
! Use powder detergent for white cotton garments, for pre-
washing, and for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
Open the detergent dispenser
drawer and pour in the deter-
gent or washing additive, as
follows.
Compartment 1: Do not pour detergent into the middle
compartment 1.
Compartment 2: Washing detergent (powder or liquid)
If liquid detergent is used, it is recommended that the remo-
vable plastic partition A (supplied) be used for proper dosage.
If powder detergent is used, place the partition into slot B.
Compartment 3: Additives (fabric softeners, etc.)
The fabric softener must not exceed the “max” level indicated
on the central pin.
Preparing the laundry
• Dividethelaundryaccordingto:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
• Emptyallgarmentpocketsandcheckthebuttons.
• Do not exceed the valueslisted in the “Table of wash
cycles”, which refer to the weight of the laundry when dry.
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1.200 g
1 towel 150-250 g
Garments requiring special care
Daily cotton: a 30°C cycle for cotton garments. It allows
for reducing consumption of energy for heating the water,
while guaranteeing excellent results. Suitable for lightly soiled
garments.
Daily synthetics: a 30°C cycle for synthetic garments. It
allows for reducing consumption of energy for heating the
water, while guaranteeing excellent results. Suitable for lightly
soiled garments.
Coloureds: a 30°C cycle that helps to preserve the colours;
suitable for coloured cotton and synthetic garments. It allows
for reducing consumption of energy for heating the water,
while guaranteeing excellent results. Suitable for lightly soiled
garments.
Delicates: use programme 4 to wash very delicate
garments. It is advisable to turn the garments inside out
before washing them. For best results, use liquid detergent
on delicate garments. For washing Silk items and Curtains,
select the relevant cycle and activate the option ; the
machine will end the cycle with the laundry soaked and
the indicator light will flash. To drain the water so that the
laundry can be removed, press the START/PAUSE button
ro the option .
Mixed: a 40°C cycle for washing cotton and synthetic
garments together. Suitable for lightly soiled underwear.
Sport (programme 11) is designed for washing lightly soiled
sports clothing (tracksuits, shorts, etc.); for best results, we
recommend not exceeding the maximum load indicated in the
“Programme table”. We recommend using liquid detergent,
and adding the amount suitable for a half-load.
Duvet: to wash double or single duvets (the weight of which
should not exceed 3.5 kg), cushions or clothes padded with
goose down such as puffa jackets, use the special wash
programme number 12. We recommend that duvets are
placed in the drum with their edges folded inwards (see
figure) and that no more than ¾ of the total volume of the
drum is used. To achieve the best results, we recommend
that a liquid detergent is used and placed inside the detergent
dispenser drawer.
Wool - Woolmark Apparel Care - Blue:
the wool wash cycle of this machine has been approved by
The Woolmark Company for the washing of wool garments
labelled as “hand wash” provided that the products are
washed according to the instructions on the garment label
and those issued by the manufacturer of this washing
machine. (M1127)
In UK, Eire, Hong Kong and India the Woolmark trade mark
is a Certification trade mark.
Anti odour: use programme 14 (Synthetics) for washing
garments with bad odours (e.g. smoke, sweat, fried food).
The programme is designed to remove bad odours while
preserving the fabric fibres.
GB
11
Troubleshooting
Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure
that the problem cannot be solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not
take in water (the indicator light for
the first wash cycle stage flashes
rapidly).
The washing machine continuously
takes in and drains water.
The washing machine does not
drain or spin.
The washing machine vibrates a lot
during the spin cycle.
The washing machine leaks.
The Functions indicator lights and the
start/pause indicator light flash, while
one of the phase in progress indicator
lights and the door locked indicator
light will remain lit in a fixed manner.
There is too much foam.
Push & Wash does not activate.
Possible causes / Solutions:
•Theapplianceisnotpluggedintothesocketfully,orisnotmakingcontact.
•Thereisnopowerinthehouse.
•Thewashingmachinedoorisnotclosedproperly.
•TheON/OFFbuttonhasnotbeenpressed.
•TheSTART/PAUSEbuttonhasnotbeenpressed.
•Thewatertaphasnotbeenopened.
•Adelayedstarthasbeenset.
•Thewaterinlethoseisnotconnectedtothetap.
•Thehoseisbent.
•Thewatertaphasnotbeenopened.
•Thereisnowatersupplyinthehouse.
•Thepressureistoolow.
•TheSTART/PAUSEbuttonhasnotbeenpressed.
•Thedrainhoseisnotfittedataheightbetween65and100cmfromthefloor
(see “Installation”).
•Thefreeendofthehoseisunderwater(see “Installation”).
•Thewalldrainagesystemisnotfittedwithabreatherpipe.
If the problem persists even after these checks, turn off the water tap, switch
the appliance off and contact the Assistance Service. If the dwelling is on one of
the upper floors of a building, there may be problems relating to water drainage,
causing the washing machine to fill with water and drain continuously. Special
anti-draining valves are available in shops and help to avoid this inconvenience.
•Thewashcycledoesnotincludedraining:somewashcyclesrequirethedrain
phase to be started manually.
• Theoption function is enabled: to complete the wash cycle, press the
START/PAUSE button (“Personalisation”).
•Thedrainhoseisbent(see “Installation”).
•Thedrainageductisclogged.
•Thedrumwasnotunlockedcorrectlyduringinstallation(see “Installation”).
•Thewashingmachineisnotlevel(see “Installation”).
Thewashingmachineistrappedbetweencabinetsandwalls(see “Installation”).
•Thewaterinlethoseisnotscrewedonproperly(see “Installation”).
•Thedetergentdispenserdrawerisblocked(forcleaninginstructions,see
“Care and maintenance”).
•Thedrainhoseisnotfixedproperly(see “Installation”).
•Switchoffthemachineandunplugit,waitforapproximately1minuteand
then switch it back on again.
If the problem persists, contact the Technical Assistance Service.
•Thedetergentisnotsuitableformachinewashing(itshoulddisplaythetext
“for washing machines” or “hand and machine wash”, or the like).
•Toomuchdetergentwasused.
• AfterswitchingonthemachineacontrolotherthanPush&Washwasactiva-
ted. Switch the machine off and press the Push & Wash button.
12
GB
Service
Before calling for Assistance:
• Check whether you can solve the problem alone (see “Troubleshooting”);
•Restarttheprogrammetocheckwhethertheproblemhasbeensolved;
•Ifthisisnotthecase,contactanauthorisedTechnicalAssistanceCentreusingthetelephonenumberprovidedonthe
guarantee certificate.
! Always request the assistance of authorised technicians.
Have the following information to hand:
• thetypeofproblem;
• theappliancemodel(Mod.);
• theserialnumber(S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the
front of the appliance by opening the door.
13
IT
Italiano,1
Sommario
Installazione, 14-15
Disimballo e livellamento
Collegamenti idraulici ed elettrici
Primo ciclo di lavaggio
Dati tecnici
Manutenzione e cura, 16
Escludere acqua e corrente elettrica
Pulire la lavabiancheria
Pulire il cassetto dei detersivi
Curare oblò e cestello
Pulire la pompa
Controllare il tubo di alimentazione dell’acqua
Precauzioni e consigli, 17
Sicurezza generale
Sistema bilanciamento del carico
Smaltimento
Descrizione della lavabiancheria e
avviare un programma, 18-19
Pannello di controllo
Spie
Avviare un programma
Programmi, 20
Push & Wash
Tabella dei programmi
Personalizzazioni, 21
Impostare la temperatura
Impostare la centrifuga
Opzioni
Detersivi e biancheria, 22
Cassetto dei detersivi
Preparare la biancheria
Capi particolari
Anomalie e rimedi, 23
Assistenza, 24
Assistenza Attiva 7 giorni su 7
IT
LAVABIANCHERIA
BWA 91082
Istruzioni per l’uso
14
IT
! È importante conservare questo libretto per
poterlo consultare in ogni momento. In caso di
vendita, di cessione o di trasloco, assicurarsi che
resti insieme alla lavabiancheria per informare il
nuovo proprietario sul funzionamento e sui relativi
avvertimenti.
! Leggere attentamente le istruzioni: ci sono
importanti informazioni sull’installazione, sull’uso
e sulla sicurezza.
Disimballo e livellamento
Disimballo
1. Disimballare la lavabiancheria.
2. Controllare che la lavabiancheria non abbia
subìto danni nel trasporto. Se fosse danneggiata
non collegarla e contattare il rivenditore.
3. Rimuovere le 4 viti di
protezione per il traspor-
to e il gommino con il
relativo distanziale, posti
nella parte posteriore
(vedi figura).
4. Chiudere i fori con i tappi di plastica in dota-
zione.
5. Conservare tutti i pezzi: qualora la lavabianche-
ria debba essere trasportata, dovranno essere
rimontati.
! Gli imballaggi non sono giocattoli per bambini.
Livellamento
1. Installare la lavabiancheria su un pavimento pia-
no e rigido, senza appoggiarla a muri, mobili o altro.
2. Se il pavimento non
fosse perfettamente
orizzontale, compensa-
re le irregolarisvitando
o avvitando i piedini
anteriori (vedi figura);
l’angolo di inclinazione,
misurato sul piano di
lavoro, non deve supe-
rare i 2°.
Un accurato livellamento dà stabilità alla mac-
china ed evita vibrazioni, rumori e spostamenti
durante il funzionamento. In caso di moquette
o di un tappeto, regolare i piedini in modo da
conservare sotto la lavabiancheria uno spazio
sufficiente per la ventilazione.
Collegamenti idraulici ed elettrici
Collegamento del tubo di alimentazione
dell’acqua
1. Collegare il tubo
di alimentazione avvi-
tandolo a un rubinetto
dacqua fredda con
bocca filettata da 3/4
gas (vedi figura).
Prima di allacciare,
far scorrere lacqua
finché non sia limpida.
2. Collegare il tubo
di alimentazione alla
lavabiancheria
avvitandolo all’appo-
sita presa dacqua,
nella parte posteriore
in alto a destra (vedi
figura).
3. Fare attenzione che nel tubo non ci siano
pieghe né strozzature.
! La pressione idrica del rubinetto deve essere
compresa nei valori della tabella Dati tecnici
(vedi pagina a fianco).
! Se la lunghezza del tubo di alimentazione
non fosse sufficiente, rivolgersi a un negozio
specializzato o a un tecnico autorizzato.
! Non utilizzare mai tubi già usati.
! Utilizzare quelli in dotazione alla macchina.
Installazione
15
IT
Collegamento del tubo di scarico
Collegare il tubo di
scarico, senza pie-
garlo, a una condut-
tura di scarico o a
uno scarico a muro
posti tra 65 e 100
cm da terra;
oppure appoggiarlo
al bordo di un lavan-
dino o di una vasca,
legando la guida in
dotazione al
rubinetto (vedi figu-
ra). L’estremità libera
del tubo di scarico
non deve rimanere
immersa nell’acqua.
! È sconsigliato usare tubi di prolunga; se in-
dispensabile, la prolunga deve avere lo stes-
so diametro del tubo originale e non superare
i 150 cm.
Collegamento elettrico
Prima di inserire la spina nella presa della cor-
rente, accertarsi che:
la presa abbia la messa a terra e sia a norma
di legge;
la presa sia in grado di sopportare il carico
massimo di potenza della macchina, indicato
nella tabella Dati tecnici (vedi a fianco);
la tensione di alimentazione sia compresa nei va-
lori indicati nella tabella Dati tecnici (vedi a fianco);
la presa sia compatibile con la spina della
lavabiancheria. In caso contrario sostituire
la presa o la spina.
! La lavabiancheria non va installata all’aperto,
nemmeno se lo spazio è riparato, perc è molto
pericoloso lasciarla esposta a pioggia e temporali.
! A lavabiancheria installata, la presa della
corrente deve essere facilmente raggiungibile.
! Non usare prolunghe e multiple.
! Il cavo non deve subire piegature o compressioni.
! Il cavo di alimentazione deve essere sostituito
solo da tecnici autorizzati.
Attenzione! L’azienda declina ogni responsabilità
qualora queste norme non vengano rispettate.
Primo ciclo di lavaggio
Dopo l’installazione, prima dell’uso, effettuare
un ciclo di lavaggio con detersivo e senza bian-
cheria impostando il programma “Auto Pulizia”
(vedi “Pulire la lavabiancheria”).
65 - 100 cm
Dati tecnici
Modello
BWA 91082
Dimensioni
larghezza cm 59,5
altezza cm 85
profondità cm 60,5
Capacità
da 1 a 9 kg
Collega-
menti elet-
trici
Vedi targhetta caratteristi-
che tecniche applicata sulla
macchina
Collega-
menti idrici
pressione massima
1 MPa (10 bar)
pressione minima
0,05 MPa (0,5 bar)
capacità del cesto 62 litri
Velocità di
centrifuga
sino a 1000 giri al minuto
Programmi
di
controllo
secondo i
regolamenti
1061/2010 e
1015/2010
programma 9;
Eco Cotone 60°C.
programma 9;
Eco Cotone 40°C.
Questa apparecchiatura è
conforme alle seguenti Diret-
tive Comunitarie:
- 2004/108/CE (Compatibili-
tà Elettromagnetica)
- 2006/95/CE (Bassa Tensione)
- 2012/19/EU - WEEE
16
IT
Manutenzione e cura
Pulire la pompa
La lavabiancheria è dotata di una pompa
autopulente che non ha bisogno di manuten-
zione. Può però succedere che piccoli oggetti
(monete, bottoni) cadano nella precamera che
protegge la pompa, situata nella parte inferiore
di essa.
! Assicurarsi che il ciclo di lavaggio sia terminato
e staccare la spina.
Per accedere alla precamera:
1. rimuovere il pan-
nello di copertura sul
lato anteriore della
macchina premendo
verso il centro, quin-
di spingere verso il
basso da entrambe
i lati ed estrarlo (vedi
figure).
2. svitare il coperchio
ruotandolo in senso
antiorario (vedi figura):
è normale che fuorie-
sca un po’ d’acqua;
3. pulire accuratamente l’interno;
4. riavvitare il coperchio;
5. rimontare il pannello assicurandosi, prima di
spingerlo verso la macchina, di aver inserito i
ganci nelle apposite asole.
Controllare il tubo di alimentazio-
ne dell’acqua
Controllare il tubo di alimentazione almeno
una volta all’anno. Se presenta screpolature e
fessure va sostituito: durante i lavaggi le forti
pressioni potrebbero provocare improvvise
spaccature.
! Non utilizzare mai tubi già usati.
Escludere acqua e corrente elettrica
Chiudere il rubinetto dell’acqua dopo ogni lavaggio.
Si limita così lusura dellimpianto idraulico della
lavabiancheria e si elimina il pericolo di perdite.
Staccare la spina della corrente quando si
pulisce la lavabiancheria e durante i lavori di
manutenzione.
Pulire la lavabiancheria
La parte esterna e le parti in gomma possono
essere puliti con un panno imbevuto di acqua
tiepida e sapone. Non usare solventi o abrasivi.
• La lavabiancheria è dotata di un programma
di “Auto Pulizia” delle parti interne che deve
essere effettuato senza alcun tipo di carico
nel cesto.
Il detersivo (nella quantità pari al 10% di quella
consigliata per capi poco sporchi) o additi-
vi specifici per la pulizia della lavabiancheria,
potranno essere utilizzati come coadiuvanti nel
programma di lavaggio. Si consiglia di effettuare
il programma di pulizia ogni 40 cicli di lavaggio.
Per attivare il programma premere contempora-
neamente i tasti A e B per 5 sec. (vedi figura).
Il programma parti automaticamente ed avrà
una durata di circa 70 minuti. Per fermare il ciclo
premere il tasto AVVIO/PAUSA.
Pulire il cassetto dei detersivi
Per estrarre il cassetto
premere la leva (1) e tirarlo
verso l’esterno (2) (vedi
figura).
Lavarlo sotto l’acqua
corrente; questa
pulizia va effettuata
frequentemente.
Curare oblò e cestello
Lasciare sempre socchiuso l’oblò per evitare
che si formino cattivi odori.
1
2
3
A
B
2
1
17
IT
Precauzioni e consigli
! La lavabiancheria è stata progettata e costruita in
conformità alle norme internazionali di sicurezza. Queste
avvertenze sono fornite per ragioni di
sicurezza e devono essere lette attentamente.
Sicurezza generale
Questo apparecchio è stato concepito esclusivamente
per un uso di tipo domestico.
•Questo apparecchio può essere usato da
bambini da 8 anni in su e da persone con
capacità fisiche, sensoriali o mentali ridotte
o con esperienza e conoscenze insufficienti
se sono supervisionati o se hanno ricevu-
to adeguata formazione in merito all’uso
dell’apparecchio in modo sicuro e capendo
i pericoli connessi. I bambini non devono
giocare con l’apparecchio. Manutenzione
e pulizia non devono essere effettuati dai
bambini senza supervisione.
Non toccare la macchina a piedi nudi o con le mani o i
piedi bagnati o umidi.
Non staccare la spina dalla presa della corrente tirando
il cavo, bensì afferrando la spina.
Non aprire il cassetto dei detersivi mentre la macchina
è in funzione.
Non toccare l’acqua di scarico, che può raggiungere
temperature elevate.
Non forzare in nessun caso l’oblò: potrebbe danneg-
giarsi il meccanismo di sicurezza che protegge da
aperture accidentali.
In caso di guasto, in nessun caso accedere ai mecca-
nismi interni per tentare una riparazione.
Controllare sempre che i bambini non si avvicinino alla
macchina in funzione.
Durante il lavaggio l’oblò tende a scaldarsi.
Se dev’essere spostata, lavorare in due o tre persone
con la massima attenzione. Mai da soli perché la mac-
china è molto pesante.
Prima di introdurre la biancheria controlla che il cestello
sia vuoto.
Sistema bilanciamento del carico
Prima di ogni centrifuga, per evitare vibrazioni eccessive e
per distribuire il carico in modo uniforme, il cestello effettua
delle rotazioni ad una velocità leggermente superiore
a quella del lavaggio. Se al termine di ripetuti tentativi
il carico non fosse ancora correttamente bilanciato la
macchina effettua la centrifuga ad una velocità inferiore a
quella prevista. In presenza di eccessivo sbilanciamento
la lavabiancheria effettua la distribuzione anzichè la
centrifuga. Per favorire una migliore distribuzione del carico
e il suo corretto bilanciamento si consiglia di mescolare
capi grandi e piccoli.
Smaltimento
•Smaltimento del materiale di imballaggio:
attenersi alle norme locali, così gli imballaggi potranno
essere riutilizzati.
La direttiva Europea 2012/19/EU (WEEE) sui rifiuti di
apparecchia¬ture elettriche ed elettroniche (RAEE), prevede
che gli elettrodo¬mestici non debbano essere smaltiti nel
normale flusso dei rifiuti solidi urbani.
Gli apparecchi dismessi devono essere raccolti separata-
mente per ottimizzare il tasso di recupero e riciclaggio dei
materiali che li compongono ed impedire potenziali danni
per la salute e l’ambiente.
Il simbolo del cestino barrato è riportato su tutti i prodotti
per ricordare gli obblighi di raccolta separata.
Quando si acquista una nuova apparecchiatura equivalente si
può consegnare il RAEE al negoziante, che è tenuto a ritirarlo
gratuitamente; i RAEE di “piccolissime dimensioni” (nessun
lato sopra i 25 cm) possono essere consegnati gratuitamente
ai negozianti anche se non si acquista nulla (solo nei negozi
con superficie di vendita superiore a 400 mq). Per ulteriori
informazioni sulla corretta dismissione degli elettrodomestici
i detentori potranno rivolgersi al servizio pubblico preposto
o ai rivenditori.
18
IT
Pannello di controllo
Descrizione della lavabiancheria e
avviare un programma
Cassetto dei detersivi: per caricare detersivi e additivi
(vedi “Detersivi e biancheria”).
Tasto ON/OFF: per accendere e spegnere la lavabiancheria.
Tasto PUSH & WASH: (vedi “Programmi”).
Manopola PROGRAMMI: per impostare i programmi. Du-
rante il programma la manopola resterà ferma.
Tasti e spie OPZIONI: per selezionare le opzioni disponibili.
La spia relativa all’opzione selezionata rimarrà accesa.
Tasto e spia BLOCCO TASTI: per attivare il blocco del
pannello di controllo, tenere premuto il tasto per circa
2 secondi. Il simbolo acceso indica che il pannello
di controllo è bloccato. In questo modo si impediscono
modifiche accidentali dei programmi (ad eccezione del
tasto ON/OFF), soprattutto se in casa ci sono dei bambini.
Per disattivare il blocco del pannello di controllo, tenere
premuto il tasto per circa 2 secondi.
Tasto TEMPERATURA: per impostare la temperatura o il
lavaggio a freddo (vedi “Personalizzazioni”).
Tasto CENTRIFUGA: per impostare la centrifuga o esclu-
derla (vedi “Personalizzazioni”).
Tasto PARTENZA RITARDATA
Ritarda l’avvio della macchina sino a 9 ore.
Premere più volte il tasto fino a far accendere la spia relativa
al ritardo desiderato. Alla quarta pressione del tasto la
l’opzione si disattiverà.
N.B.: Una volta premuto il tasto AVVIO/PAUSA, si può
modificare il valore del ritardo solo diminuendolo fino ad
avviare il programma impostato.
! E’ attivo con tutti i programmi.
SPIE AVANZAMENTO CICLO: per seguire lo stato di
avanzamento del programma di lavaggio.
La spia accesa indica la fase in corso.
Spia OBLÒ BLOCCATO: per capire se l’oblò è apribile
(vedi pagina a fianco).
Tasto e spia AVVIO/PAUSA: per avviare i programmi o
interromperli momentaneamente.
N.B.: per mettere in pausa il lavaggio in corso, premere
questo tasto, la spia relativa lampeggerà con colore
ambra mentre quella della fase in corso sarà accesa fissa.
Se la spia OBLÒ BLOCCATO sarà spenta, si potrà
aprire l’oblò (attendere 3 minuti circa).
Per far ripartire il lavaggio dal punto in cui è stato
interrotto, premere nuovamente questo tasto.
Modalità stand by
Questa lavatrice, in conformità alle nuove normative
legate al risparmio energetico, è dotata di un sistema
di autospegnimento (stand by) che entra in funzione
dopo circa 30 minuti nel caso di non utilizzo. Premere
brevemente il tasto ON-OFF e attendere che la macchina
si riattivi.
Spia
OBLÒ
BLOCCATO
Tasto
TEMPERATURA
MANOPOLA
PROGRAMMI
Cassetto dei detersivi
Tasto
ON/OFF
Tasto
CENTRIFUGA
Tasto e spia
AVVIO/PAUSA
Tasto
PARTENZA
RITARDATA
Tasti e spie
OPZIONE
Tasto
PUSH & WASH
SPIE AVANZAMENTO
CICLO
Tasto e spia
BLOCCO
TASTI
19
IT
Spie fase in corso
Una volta selezionato e avviato il ciclo di lavaggio desidera-
to, le spie si accenderanno progressivamente per indicarne
lo stato di avanzamento:
Tasti opzione e relative spie
Selezionando un’opzione la spia relativa si illuminerà.
Se l’opzione selezionata non è compatibile con il programma
impostato la spia relativa lampeggerà e l’opzione non verrà
attivata.
Se l’opzione selezionata non è compatibile con un’altra pre-
cedentemente impostata, l’incompatibilità verrà segnalata
con il lampeggio della spia ed un segnale acustico (3 beep)
e verrà attivata solo la seconda, la spia dell’opzione attivata
si illuminerà.
Spia oblò bloccato
La spia accesa indica che l’oblò è bloccato per impedire
l’apertura; per aprire l’oblò è necessario che la spia sia
spenta (attendere 3 minuti circa).
Per aprire l’oblò mentre un ciclo è in corso premere il pul-
sante AVVIO/PAUSA; se la spia OBLÒ BLOCCATO è spenta
sarà possibile aprire l’oblò.
Spie
Le spie forniscono informazioni importanti.
Ecco che cosa dicono:
Partenza ritardata
Se è stata attivata l’opzione “Partenza ritardata” (vedi “Per-
sonalizzazioni”), dopo avere avviato il programma, inizierà
a lampeggiare la spia relativa al ritardo selezionato:
Col trascorrere del tempo verrà visualizzato il ritardo resi-
duo con il lampeggio della spia relativa:
Trascorso il ritardo selezionato avrà inizio il programma
impostato.
Avviare un programma
Programmazione rapida
1. CARICARE LA BIANCHERIA.
Aprire la porta oblò. Caricare la biancheria facendo
attenzione a non superare la quantità di carico indicata
nella tabella programmi della pagina seguente.
2. DOSARE IL DETERSIVO.
Estrarre il cassetto e versare il detersivo nelle apposite
vaschette come spiegato in “Detersivi e biancheria”.
3. CHIUDERE L’OBLO’.
4. Premere il tasto PUSH & WASH per avviare il
programma di lavaggio.
Programmazione tradizionale
1. Accendere la lavabiancheria premendo il tasto
ON/OFF. Tutte le spie si accenderanno per qualche
secondo, poi rimarranno accese le spie ralative alle
impostazioni del programma selezionato e pulserà la spia
AVVIO/PAUSA.
2. Caricare la biancheria e chiudere l’oblò.
3. Impostare con la manopola PROGRAMMI il programma
desiderato.
4. Impostare la temperatura di lavaggio (vedi “Personalizza-
zioni”).
5. Impostare la velocità di centrifuga (vedi “Personalizzazioni”).
6. Versare detersivo e additivi (vedi “Detersivi e biancheria”).
7. Selezionare le opzioni desiderate.
8. Avviare il programma premendo il tasto AVVIO/PAUSA e
la spia relativa rimarrà accesa fissa di colore verde.
Per annullare il ciclo impostato mettere la macchina in pausa
premendo il tasto AVVIO/PAUSA e scegliere un nuovo ciclo.
9. Al termine del programma si illuminerà la spia . Quan-
do la spia OBLO’ BLOCCATO si spegnesarà possibile
aprire l’oblò (attendere 3 minuti circa). Estrarre la biancheria e
lasciare l’oblò socchiuso per far asciugare il cestello. Spegne-
re la lavabiancheria premendo il tasto ON/OFF.
Lavaggio
Risciacquo
Centrifuga
Scarico
Fine lavaggio
20
IT
Programmi
Tabella dei programmi
Push & Wash
Questa funzione permette di avviare un ciclo di lavaggio anche a macchina spenta senza dover preventivamente premere il
tasto ON/OFF o, successivamente all’accensione della macchina, senza aver azionato nessun ulteriore tasto e/o manopola
(diversamente il programma Push & Wash sarà disattivato). Per avviare il ciclo Push & Wash tenere premuto il pulsante per 2
secondi. La spia accesa indica che il ciclo è avviato. Il ciclo di lavaggio è ideale per capi in cotone e sintetici funzionando ad
una temperatura di lavaggio di 30° e una velocità massima di centrifuga pari a 1000 giri al minuto. Carico max. 4 kg. (Durata
ciclo 45’),
Come funziona?
1. Caricare la biancheria (capi in cotone e/o sintetici) e chiudere l’oblò.
2. Versare detersivo e additivi.
3. Avviare il programma tenendo premuto per 2 secondi il tasto Push & Wash. La spia relativa si illuminerà di colore verde e
l’oblò si bloccherà (simbolo oblò bloccato acceso).
N.B.: L’avvio del lavaggio attraverso il tasto Push & Wash attiva un ciclo automatico consigliato per cotone e sintetici non
personalizzabile. Tale programma non permette la possibilità di impostare ulteriori opzioni.
Per aprire la porta mentre il ciclo automatico è in corso premere il tasto AVVIO/PAUSA; se il simbolo oblò bloccato è spento
sarà possibile aprire l’oblò. Premere nuovamente il tasto AVVIO/PAUSA per far ripartire il programma dal punto in cui era
stato interrotto.
4. Al termine del programma si illuminerà la spia .
* Selezionando il programma ed escludendo la centrifuga la macchina effettuerà solo lo scarico.
La durata del ciclo indicata sul display o sul libretto è una stima calcolata in base a condizioni standard. Il tempo effettivo può variare in base a numerosi fattori quali tem-
peratura e pressione dell’acqua in ingresso, temperatura ambiente, quantità di detersivo, quantità e tipo di carico, bilanciamento del carico, opzioni aggiuntive selezionate.
1) Programma di controllo secondo il regolamento 1061/2010: impostare il programma 9 con una temperaura di 60°C.
Questo ciclo è adatto per pulire un carico di cotone normalmente sporco ed è il più efficiente in termini di consumo combinato di energia e di acqua, da usare su capi lavabili
a 60 °C. La temperatura effettiva di lavaggio può differire da quella indicata.
2) Programma di controllo secondo il regolamento 1061/2010: impostare il programma 9 con una temperaura di 40°C.
Questo ciclo è adatto per pulire un carico di cotone normalmente sporco ed è il più efficiente in termini di consumo combinato di energia e di acqua, da usare su capi lavabili
a 40 °C. La temperatura effettiva di lavaggio può differire da quella indicata.
Per tutti Test Institutes:
3) Programma cotone lungo: impostare il programma 6 con una temperatura di 40°C.
4) Programma sintetico lungo: impostare il programma 7 con una temperatura di 40°C.
Programmi
Descrizione del Programma
Temp.
max.
(°C)
Veloci-
tà max.
(giri al
minuto)
Detersivi
Carico max.
(Kg)
Umidità residua
%
Consumo ener-
gia kWh
Acqua totale lt
Durata ciclo
Lavaggio
Ammorbi-
dente
Quotidiani 30° ECO
1 Cotone giornaliero
30° 1000
4,5 - - - 100’
2 Sintetico giornaliero
30° 1000
4,5 - - - 90’
3 Colorati
30° 1000
4,5 - - - 95’
4 Delicati
30° 0
1 - - - 80’
5
Rapido 30min: Per rinfrescare rapidamente capi poco sporchi (non indicato
per lana, seta e capi da lavare a mano).
30° 800
4,5 70 0,18 42 30’
Tradizionali
6
Cotone (3): bianchi poco sporchi e colori delicati.
40°
(Max.60°)
1000
9 62 1,10 97 225’
7
Sintetici (4): colori delicati poco sporchi.
40°
(Max.60°)
1000
4,5 46 0,74 59 125’
8 Mix
40° 1000
9 - - - 105’
9
Eco Cotone 60°C (1): bianchi e colorati resistenti molto sporchi.
60° 1000
9 62 1,30 57,4 240’
9
Eco Cotone 40°C (2): bianchi poco sporchi e colori delicati.
40° 1000
9 62 1,10 97 225’
10
Cotone bianchi: bianchi e colorati resistenti molto sporchi.
60°
(Max.90°)
1000
9 - - - 200’
Speciali
11 Sport
30° 600
4 - - - 60’
12
Piumini: per capi imbottiti in piuma d’oca. 30° 1000
3,5 - - - 115’
13
Lana: per lana, cachemire, ecc. 40° 800
2 - - - 85’
14 Anti Odore
40° 1000
3,5 - - - 105’
Risciacquo + Centrifuga - 1000
-
9 - - - 55’
Centrifuga + Scarico - 1000
- -
9 - - - 10’
Solo scarico * -
- -
9 - - - 3’
1 / 1

Indesit BWA 91082X W EU Guida utente

Categoria
Lavatrici
Tipo
Guida utente

in altre lingue