HOTPOINT/ARISTON FMG 823B EU.M Guida utente
- Categoria
- Lavatrici
- Tipo
- Guida utente
1
GB
WASHING MACHINE
Instructions for use
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 4
Cutting off the water and electricity supplies
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and tips, 5
General safety
Disposal
Description of the washing machine, 6-7
Control panel
Display
Running a wash cycle, 8
Wash cycles and options, 9
Table of programmes and wash cycles
Wash options
Detergents and laundry, 10
Detergent dispenser drawer
Preparing the laundry
Special wash cycles
Load balancing system
Troubleshooting, 11
Service, 12
FMG 823
English,1
GB
ES
PT
Español,13
Português,25
IT
Italiano,37
2
GB
Installation
! This instruction manual should be kept in a safe
place for future reference. If the washing machine
is sold, transferred or moved, make sure that the
instruction manual remains with the machine so
that the new owner is able to familiarise himself/
herself with its operation and features.
! Read these instructions carefully: they
contain vital information relating to the safe
installation and operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its
packaging.
2. Make sure that the washing machine has
not been damaged during the transportation
process. If it has been damaged, contact the
retailer and do not proceed any further with
the installation process.
3. Remove the 3
protective screws
(used during
transportation)
and the rubber
washer with the
corresponding
spacer, located on
the rear part of the
appliance (see figure).
4. Close off the holes using the plastic plugs
provided.
5. Keep all the parts in a safe place: you will
need them again if the washing machine
needs to be moved to another location.
! Packaging materials should not be used as
toys for children.
Levelling
1. Install the washing machine on a flat sturdy
floor, without resting it up against walls,
furniture cabinets or anything else.
2. If the floor is
not perfectly level,
compensate for
any unevenness
by tightening or
loosening the
adjustable front
feet (see figure); the
angle of inclination,
measured in relation
to the worktop, must
not exceed 2°.
Levelling the machine correctly will provide
it with stability, help to avoid vibrations and
excessive noise and prevent it from shifting
while it is operating. If it is placed on carpet or
a rug, adjust the feet in such a way as to allow
a sufficient ventilation space underneath the
washing machine.
Connecting the electricity and
water supplies
Connecting the water inlet hose
1. Connect the inlet
hose by screwing it to
a cold water tap using
a 3/4 gas threaded
connection (see
figure).
Before performing
the connection, allow
the water to run freely
until it is perfectly
clear.
2. Connect the
inlet hose to the
washing machine by
screwing it onto the
corresponding water
inlet of the appliance,
which is situated on
the top right-hand
side of the rear part
of the appliance (see
figure).
3. Make sure that the hose is not folded over
or bent.
! The water pressure at the tap must fall within
the range of values indicated in the Technical
data table (see next page).
! If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
3
GB
Connecting the drain hose
Connect the drain
hose, without bending
it, to a drain duct or
a wall drain situated
between 65 and 100
cm from the floor.
Alternatively, place
the drain hose
over the edge of
a washbasin or
bathtub, by fastening
the guide (which
can be purchased
at the technical
assistance centre) to
the tap (see figure).
The free end of the
hose should not be underwater.
! We advise against the use of hose
extensions; if it is absolutely necessary, the
extension must have the same diameter as the
original hose and must not exceed 150 cm in
length.
Electrical connections
Before plugging the appliance into the
electricity socket, make sure that:
• thesocketisearthedandcomplieswithall
applicable laws;
• thesocketisabletowithstandthe
maximum power load of the appliance as
indicated in the Technical data table (see
opposite);
• thepowersupplyvoltagefallswithinthe
values indicated in the Technical data table
(see opposite);
• thesocketiscompatiblewiththeplugof
the washing machine. If this is not the case,
replace the socket or the plug.
! The washing machine must not be installed
outdoors, even in covered areas. It is
extremely dangerous to leave the appliance
exposed to rain, storms and other weather
conditions.
65 - 100 cm
! When the washing machine has been
installed, the electricity socket must remain
within easy reach.
! Do not use extension cords or multiple
sockets.
! The cable should not be bent or
compressed.
! The power supply cable must only be
replaced by authorised technicians.
Warning! The company shall not be held
responsible in the event that these standards
are not observed.
The first wash cycle
Once the appliance has been installed, and
before you use it for the first time, run a wash
cycle with detergent and no laundry, using
wash cycle number auto clean (see “Cleaning
the washing machine”).
Technical data
Model
FMG 823
Dimensions
width 59.5 cm
height 85 cm
depth 57.7 cm
Capacity
from 1 to 8 kg
Electrical
connections
please refer to the technical
data plate fixed to the ma-
chine
Water con-
nections
maximum pressure
1 MPa (10 bar)
minimum pressure
0.05 MPa (0.5 bar)
drum capacity 54 litres
Spin speed
up to 1200 rotations per
minute
Test wash
cycles in
accordance
with re-
gulations
1061/2010
1015/2010
programme 9
;
Eco Cotton 60°C.
programme 9
;
Eco Cotton 40°C.
This appliance conforms to
the following EC Directives:
- EMC 2014/30/EU (Electro-
magnetic Compatibility)
- LVD 2014/35/EU (Low
Voltage)
- 2012/19/EU - (WEEE)
4
GB
Care and maintenance
Cutting off the water and
electricity supplies
•Turnoffthewatertapaftereverywashcycle.
This will limit wear on the hydraulic system
inside the washing machine and help to
prevent leaks.
•Unplugthewashingmachinewhencleaning
it and during all maintenance work.
Cleaning the washing machine
•Theouterpartsandrubbercomponents
of the appliance can be cleaned using a soft
cloth soaked in lukewarm soapy water. Do not
use solvents or abrasives.
•Thewashingmachinehasaautoclean
programme for its internal parts that must be
run with no load in the drum.
To help the wash cycle
you may want to use
either the detergent
(i.e. a quantity 10%
the quantity specified
for lightly-soiled
garments) or special
additives to clean the
washing machine. We
recommend running a
cleaning programme every 40 wash cycles.
To start the programme press buttons A and
B simultaneously for 5 seconds (see figure).
The programme will start automatically and will
run for about 70 minutes. To stop the cycle
press the START/PAUSE button.
Cleaning the detergent dispenser
drawer
Remove the dispenser
by raising it and
pulling it out (see
figure).
Wash it under running
water; this operation
should be repeated
frequently.
1
2
Caring for the door and drum of
your appliance
•Alwaysleavetheportholedoorajarinorder
to prevent unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-
cleaning pump which does not require any
maintenance. Sometimes, small items (such as
coins or buttons) may fall into the pre-chamber
which protects the pump, situated in its bottom
part.
! Make sure the wash cycle has finished and
unplug the appliance.
To access the pre-chamber:
1. using a
screwdriver, remove
the cover panel on
the lower front part of
the washing machine
(see figure);
2. unscrew the lid
by rotating it anti-
clockwise (see figure):
a little water may
trickle out. This is
perfectly normal;
3. clean the inside thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks
are securely in place before you push it onto
the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If
there are any cracks, it should be replaced
immediately: during the wash cycles, water
pressure is very strong and a cracked hose
could easily split open.
! Never use second-hand hoses.
5
GB
Precautions and tips
! This washing machine was designed and constructed
in accordance with international safety regulations. The
following information is provided for safety reasons and
must therefore be read carefully.
General safety
• Thisappliancewasdesignedfordomesticuseonly.
• This appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given
supervision or instruction concerning use of
the appliance in a safe way and understand
the hazards involved. Children shall not
play with the appliance. Cleaning and user
maintenance shall not be made by children
without supervision.
• Donottouchthemachinewhenbarefootorwithwetor
damp hands or feet.
• Donotpullonthepowersupplycablewhenunplugging
the appliance from the electricity socket. Hold the plug
and pull.
• Donotopenthedetergentdispenserdrawerwhilethe
machine is in operation.
• Donottouchthedrainedwaterasitmayreach
extremely high temperatures.
• Neverforcetheportholedoor.Thiscoulddamagethesafety
lock mechanism designed to prevent accidental opening.
• Iftheappliancebreaksdown,donotunderany
circumstances access the internal mechanisms in an
attempt to repair it yourself.
• Alwayskeepchildrenwellawayfromtheappliancewhile
it is operating.
• Thedoorcanbecomequitehotduringthewashcycle.
• Iftheappliancehastobemoved,workinagroupoftwo
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.
• Beforeloadinglaundryintothewashingmachine,make
sure the drum is empty.
Disposal
•Disposingofthepackagingmaterials:observelocal
regulations so that the packaging may be re-used.
•TheEuropeanDirective2012/19/EUonWasteElectrical
and Electronic Equipment, requires that old household
electrical appliances must not be disposed of in the
normal unsorted municipal waste stream. Old appliances
must be collected separately in order to optimise the
recovery and recycling of the materials they contain and
reduce the impact on human health and the environment.
The crossed out “wheeled bin” symbol on the product
reminds you of your obligation, that when you dispose of
the appliance it must be separately collected. Consumers
should contact their local authority or retailer for information
concerning the correct disposal of their old appliance.
6
GB
Description of the washing
machine
Control panel
TEMPERATURE
button
WASH
CYCLE
SELECTOR
KNOB
Detergent dispenser drawer
ON/OFF
button
SPIN
button
START/PAUSE
button and indicator
light
DISPLAY
DELAY
TIMER
button
OPTION
buttons and
indicator lights
Detergent dispenser drawer: used to dispense
detergents and washing additives (see “Detergents and
laundry”).
ON/OFF button: press this briefly to switch the
machine on or off. The START/PAUSE indicator light which
flashes slowly in a green colour shows that the machine is
switched on. To switch off the washing machine during the
wash cycle, press and hold the button for approximately 3
seconds; if the button is pressed briefly or accidentally the
machine will not switch off.
If the machine is switched off during a wash cycle, this
wash cycle will be cancelled.
WASH CYCLE SELECTOR KNOB: used to set the
desired wash cycle (see “Table of programmes and wash
cycles”).
OPTION buttons and indicator lights: press to select the
available options. The indicator light corresponding to the
selected option will remain lit.
CLEANING ACTION
button : to select the desired
wash intensity.
TEMPERATURE button: press to reduce or completely
exclude the temperature; the value appears on the display.
SPIN button: press to reduce or completely exclude
the spin cycle; the value appears on the display.
DELAYED START button: press to set a delayed start
for the selected wash cycle; the delay period appears on
the display.
START/PAUSE button and indicator light: when the green
indicator light flashes slowly, press the button to start a
wash cycle. Once the cycle has begun the indicator light
will remain lit in a fixed manner. To pause the wash cycle,
press the button again; the indicator light will flash in an
amber colour. If the symbol is not illuminated, the door
may be opened (wait approximately 3 minutes). To start
the wash cycle from the point at which it was interrupted,
press the button again.
CHILD LOCK button: to activate the control panel lock,
press and hold the button for approximately 2 seconds.
When the symbol is illuminated, the control panel
is locked (apart from the ON/OFF button). This means it
is possible to prevent wash cycles from being modified
accidentally, especially where there are children in the
home. To deactivate the control panel lock, press and hold
the button for approximately 2 seconds.
Standby mode
This washing machine, in compliance with new energy
saving regulations, is fitted with an automatic standby
system which is enabled after about 30 minutes if no
activity is detected. Press the ON-OFF button briefly and
wait for the machine to start up again.
CLEANING
ACTION
button
CHILD
LOCK
button
7
GB
Display
The display is useful when programming the machine and provides a great deal of information.
The duration of the available wash cycles and the remaining time of a running cycle appear in section A (the display will show
the maximum duration of the cycle chosen, which may decrease after several minutes, since the effective duration of the
programme varies depending on the wash load and the settings chosen); if the DELAYED START option has been set, the
countdown to the start of the selected wash cycle will appear.
Pressing the corresponding button allows you to view the maximum spin speed and temperature values attained by the
machine during the set wash cycle, or the values selected most recently, if these are compatible with the set wash cycle.
The “wash cycle phases” corresponding to the selected wash cycle and the “wash cycle phase” of the running wash cycle
appear in section B:
Main wash
Rinse
Spin
Pump out
The icons corresponding to “temperature”, “spin” and “delayed start” (working from the left) are displayed in section C.
The “temperature” bars indicate the maximum temperature level which may be selected for the set cycle.
The “spin” bars indicate the maximum spin level which may be selected for the set cycle.
The “delay” symbol , when lit, indicates that the set “delayed start” value has appeared on the display.
DOOR LOCKED indicator light:
The lit symbol indicates that the door is locked. To prevent any damage, wait until the symbol turns off before opening the door
(wait approximately 3 minutes).
To open the door while a cycle is in progress, press the START/PAUSE button; if the DOOR LOCKED symbol is switched
off the door may be opened (wait approximately 3 minutes).
B
C
A
8
GB
Running a wash cycle
1. SWITCH THE MACHINE ON. Press the button;
the START/PAUSE indicator light will flash slowly in a
green colour.
2. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed
the maximum load value indicated in the table of
programmes and wash cycles on the following page.
3. MEASURE OUT THE DETERGENT. Pull out the
detergent dispenser drawer and pour the detergent into
the relevant compartments as described in “Detergents
and laundry”.
4. CLOSE THE DOOR.
5. SELECT THE WASH CYCLE. Use the WASH CYCLE
SELECTOR knob to select the desired wash cycle. A
temperature and spin speed is set for each wash cycle;
these values may be adjusted. The duration of the cycle
will appear on the display.
6. CUSTOMISE THE WASH CYCLE. Use the relevant
buttons:
Modify the temperature and/or spin speed.
The machine automatically displays the maximum
temperature and spin speed values set for the selected
cycle, or the most recently-used settings if they are
compatible with the selected cycle. The temperature
can be decreased by pressing the button, until
the cold wash “OFF” setting is reached. The spin
speed may be progressively reduced by pressing
the button, until it is completely excluded (the
“OFF” setting). If these buttons are pressed again, the
maximum values are restored.
! Exception: if the 4 programme is selected, the
temperature can be increased up to a value of 90°C.
Setting a delayed start.
To set a delayed start for the selected cycle, press the
corresponding button repeatedly until the required delay
period has been reached. When this option has been
activated, the symbol lights up on the display. To
remove the delayed start setting, press the button until
the text “OFF” appears on the display.
Set the desired wash intensity.
Option makes it possible to optimise washing based
on the level of soil in the fabrics and on desired wash
cycle intensity.
Select the wash programme: the cycle will be
automatically set to “Normal” as optimised for garments
with an average level of soil (this setting is not applicable
to the “Wool” cycle, which is automatically set to
“Delicate”).
For heavily-soiled garments press button until
the “Intensive” level is reached. This level ensures
a high-performance wash due to a larger quantity of
water used in the initial phase of the cycle and due to
increased drum rotation. It is useful when removing the
most stubborn stains.
It can be used with or without bleach. If you desire
bleaching, insert the extra tray compartment (4) into
compartment 1. When pouring in the bleach, be careful
not to exceed the “max” level marked on the central
pivot (see figure pag. 10).
For lightly-soiled garments or a more delicate treatment
of the fabrics, press button until the “Delicate”
level is reached. The cycle will reduce drum rotation
to ensure washing results that are perfect for delicate
garments.
Modify the cycle settings.
• Pressthebuttontoenabletheoption;theindicator
light corresponding to the button will switch on.
• Pressthebuttonagaintodisabletheoption;the
indicator light will switch off.
! If the selected option is not compatible with the set
wash cycle, the indicator light will flash and the option
will not be activated.
! If the selected option is not compatible with a previously
selected one, the indicator light corresponding to the first
function selected will flash and only the second option will
be activated; the indicator light for the option which has
been activated will be illuminated.
! The options may affect the recommended load value
and/or the duration of the cycle.
7. START THE WASH CYCLE. Press the START/
PAUSE button. The corresponding indicator light will
turn green, remaining lit in a fixed manner, and the
door will be locked (the DOOR LOCKED symbol will
be lit). To change a wash cycle while it is in progress,
pause the washing machine using the START/PAUSE
button (the START/PAUSE indicator light will flash
slowly in an amber colour); then select the desired cycle
and press the START/PAUSE button again.
To open the door while a cycle is in progress, press
the START/PAUSE button; if the DOOR LOCKED
symbol is switched off the door may be opened (wait
approximately 3 minutes). Press the START/PAUSE
button again to restart the wash cycle from the point at
which it was interrupted.
8. THE END OF THE WASH CYCLE. This will be
indicated by the text “END” on the display; when the
DOOR LOCKED symbol switches off the door may
be opened (wait approximately 3 minutes). Open the
door, unload the laundry and switch off the machine.
! If you wish to cancel a cycle which has already begun,
press and hold the button. The cycle will be stopped
and the machine will switch off.
9
GB
Wash cycles and options
Wash options
! If the selected option is not compatible with the set
wash cycle, the indicator light will flash and the option will
not be activated.
! If the selected option is not compatible with a previously
selected one, the indicator light corresponding to the first
function selected will flash and only the second option will be
activated; the indicator light for the option which has been
activated will be illuminated.
Extra Rinse
By selecting this option, the efficiency of the rinse is
increased and optimal detergent removal is guaranteed. It
is particularly useful for sensitive skin.
Table of programmes and wash cycles
Wash cycles
Description of the wash cycle
Max.
temp.
(°C)
Max.
speed
(rpm)
Detergents
Max. load (kg)
Residual dam-
pness%
Energy con-
sumptionkWh
Total water lt
Cycle duration
Prewash
Wash
Bleach
Fabric
softener
CLEAN Plus
1
Anti Stain
40° 1200
-
4 - - -
**
2
Anti Stain Quick
40° 1200 -
-
4 - - -
**
3
Whites
60° 1200
-
4 - - -
**
4
Cotton 60°C: heavily soiled whites and resistant colours.
60°
(Max. 90°)
1200
8 - - -
**
5
Synthetics: heavily soiled resistant colours.
60° 1000
3,5 44 0,78 33 130’
5
Synthetics (3): lightly soiled resistant colours.
40° 1000
3,5 - - -
**
SPECIALS
6
Anti allergy Plus
60° 1200 -
4 - - -
**
7
Anti allergy Delicate
40° 1200 -
4 - - -
**
8
Baby
40° 1000
4 - - -
**
9
Eco Cotton 60°C (1): heavily soiled whites and resistant colours.
60° 1200 -
-
8 53 1,17 54,7 190’
9
Eco Cotton 40°C (2): lightly soiled resistant and delicate colours.
40° 1200 -
-
8 53 0,93 82 170’
10
Wool: for wool, cashmere, etc.
40° 800 -
-
1,5 - - -
**
11
Delicates
30° 0 -
-
1 - - -
**
COLD
12
Cotton 20°C: lightly soiled resistant and delicate colours.
20° 1200 -
8 - - -
**
13
Synthetics
Cold Water
1000 -
-
3 - - -
**
14
Fast 30’
Cold Water
800 -
-
3 70 0,05 36 30’
Partial Programmes
Rinse
- 1200 - - -
8 - - -
**
Spin and Pump out
- 1200 - - - - 8 - - -
**
Pump out only *
- OFF - - - - 8 - - -
**
1) Test wash cycle in compliance with regulation 1061/2010: set wash cycle 9 with a temperature of 60°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be washed at
60°C . The actual washing temperature may differ from the indicated value.
2) Test wash cycle in compliance with regulation 1061/2010: set wash cycle 9 with a temperature of 40°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be washed at
40°C . The actual washing temperature may differ from the indicated value.
For all Test Institutes:
2) Long wash cycle for cottons: set wash cycle 9 with a temperature of 40°C.
3) Long wash cycle for synthetics: set wash cycle 5 with a temperature of 40°C.
Prewash
If this function is selected, the pre-wash cycle will run; this
is useful for removing stubborn stains.
N.B.: Put the detergent in the relevant compartment.
* If you select programme and exclude the spin cycle, the machine will drain only.
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-
ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
** The duration of the wash cycle can be checked on the display.
10
GB
Detergents and laundry
Detergent dispenser drawer
Successful washing results also depend on the correct
dose of detergent: adding too much detergent will not
necessarily result in a more efficient wash, and may in
fact cause build up on the inside of your appliance and
contribute to environmental pollution.
! Use powder detergent for white cotton garments, for pre-
washing, and for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
! Do not use hand washing detergents; they create too
much foam.
Open the detergent
dispenser drawer and pour
in the detergent or washing
additive, as follows.
compartment 1: Pre-
wash detergent (powder)
Before pouring in the
detergent, make sure that
extra compartment 4 has
been removed.
compartment 2: Detergent for the wash cycle
(powder or liquid)
If liquid detergent is used, it is recommended that the
removable plastic partition A (supplied) be used for proper
dosage.
If powder detergent is used, place the partition into slot B.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
extra compartment 4: Bleach
Preparing the laundry
• Dividethelaundryaccordingto:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
• Emptyallgarmentpocketsandcheckthebuttons.
• Donotexceedthelistedvalues,whichreferto
the weight of the laundry when dry: see “Table of
programmes and wash cycles”.
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1,200 g
1 towel 150-250 g
Special wash cycles
Anti Stain: the programme 1 is suitable to heavily-soiled
garments with resistant colours. It ensures a washing class
that is higher than the standard class (A class).
When running the programme, do not mix garments of
different colours. We recommend the use of powder
detergent. Pre-treatment with special additives is
recommended if there are obstinate stains.
Anti Stain Quick: this programme is ideal for washing
the most difficult daily stains in 1 hour. It is ideal for mixed
fabrics and coloured garments, caring for your clothes as
it washes.
M
AX
1
2
4
3
A
B
Whites: use this cycle 3 to wash white clothes. The
programme is designed to maintain the brightness of white
clothes over time. Use powder detergent for best results.
Anti allergy Plus: use programme 6 to remove major
allergens such as pollen, mites, cat’s and dog’s hair.
Anti allergy Delicate: cycle studied for cotton laundry and
other resistant fabrics to guarantee the removal of pollen and
cat and dog hair already at 40°.
Baby: use the special wash cycle 8 to remove the remove
the soiling typically caused by babies, while removing all
traces of detergent from nappies in order to prevent the
delicate skin of babies from suffering allergic reactions. The
cycle has been designed to reduce the amount of bacteria
by using a greater quantity of water and optimising
the effect of special disinfecting additives added to the
detergent.
Wool - Woolmark Apparel Care - Green:
the wool wash cycle of this machine has been approved
by The Woolmark Company for the washing of wool
garments labelled as “hand wash” provided that the
products are washed according to the instructions on the
garment label and those issued by the manufacturer of this
washing machine
Delicates: use programme 11 to wash very delicate
garments having strasses or sequins.
To wash silk garments and curtains select the cycle 11
and set the “Delicate” level from option .
We recommend turning the garments inside out before
washing and placing small items into the special bag
for washing delicates. Use liquid detergent on delicate
garments for best results.
Cotton 20°C ideal for lightly soiled cotton loads.
The effective performance levels achieved at cold
temperatures, which are comparable to washing at 40°,
are guaranteed by a mechanical action which operates at
varying speed, with repeated and frequent peaks.
The Cycles 13-14 assure energy saving by eliminating
the need of heating water! These innovative programmes
are available for various fabrics (lightly soiled). For the
best washing results we recommend the usage of a liquid
detergent; it is advisable to pre-treat cuffs, collars and
stains.
Load balancing system
Before every spin cycle, to avoid excessive vibrations
before every spin and to distribute the load in a uniform
manner, the drum rotates continuously at a speed which
is slightly greater than the washing rotation speed. If,
after several attempts, the load is not balanced correctly,
the machine spins at a reduced spin speed. If the load is
excessively unbalanced, the washing machine performs
the distribution process instead of spinning. To encourage
improved load distribution and balance, we recommend
small and large garments are mixed in the load.
11
GB
Troubleshooting
Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Service (see “ Service”),
make sure that the problem cannot be solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not fill
with water (the text “H2O” flashes
on the display).
The washing machine continuously
takes in and drains water.
The washing machine does not
drain or spin.
The washing machine vibrates a
lot during the spin cycle.
The washing machine leaks.
The “option” and START/PAUSE
indicator lights flash rapidly and an
error code appears on the display
(e.g.: F-01, F-..).
There is too much foam.
Possible causes / Solutions:
• Theapplianceisnotpluggedintothesocketfully,ornotenoughtomakecontact.
• Thereisnopowerinthehouse.
• Thewashingmachinedoorisnotclosedproperly.
• TheON/OFFbuttonhasnotbeenpressed.
• TheSTART/PAUSEbuttonhasnotbeenpressed.
• Thewatertaphasnotbeenopened.
• Adelayedstarthasbeenset.
• Thewaterinlethoseisnotconnectedtothetap.
• Thehoseisbent.
• Thewatertaphasnotbeenopened.
• Thereisnowatersupplyinthehouse.
• Thepressureistoolow.
• TheSTART/PAUSEbuttonhasnotbeenpressed.
• Thedrainhoseisnotfittedataheightbetween65and100cmfromthefloor
(see “Installation”).
• Thefreeendofthehoseisunderwater(see “Installation”).
• Thewalldrainagesystemisnotfittedwithabreatherpipe.
If the problem persists even after these checks, turn off the water tap, switch the
appliance off and contact the Technical Assistance Service. If the dwelling is on one
of the upper floors of a building, there may be problems relating to water drainage,
causing the washing machine to fill with water and drain continuously. Special anti-
draining valves are available in shops and help to prevent this inconvenience.
• Thewashcycledoesnotincludedraining:somecyclesrequirethedraining
process to be enabled manually.
• Thedrainhoseisbent(see “Installation”).
• Thedrainageductisclogged.
• Thedrumwasnotunlockedcorrectlyduringinstallation(see “Installation”).
• Thewashingmachineisnotlevel(see “Installation”).
• Thewashingmachineistrappedbetweencabinetsandwalls(see “Installation”).
• Thewaterinlethoseisnotscrewedonproperly(see “Installation”).
• Thedetergentdispenserdrawerisblocked(forcleaninginstructions,see “Care
and maintenance”).
• Thedrainhoseisnotfixedproperly(see “Installation”).
• Switchoffthemachineandunplugit,waitforapproximately1minuteandthen
switch it back on again.
If the problem persists, contact the Technical Assistance Service.
• Thedetergentisnotsuitableformachinewashing(itshoulddisplaythetext“for
washing machines” or “hand and machine wash”, or the like).
• Toomuchdetergentwasused.
12
GB
Service
Before contacting the Technical Assistance Service:
• Checkwhetheryoucansolvetheproblemalone(see “Troubleshooting”);
• Restartthewashcycletocheckwhethertheproblemhasbeensolved;
• Ifthisisnotthecase,contactanauthorisedTechnicalAssistanceCentre.
! Always request the assistance of authorised technicians.
Have the following information to hand:
• thetypeofproblem;
• theappliancemodel(Mod.);
• theserialnumber(S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the
front of the appliance by opening the door.
ES
13
Español
ES
LAVADORA
Sumario
Instalación, 14-15
Desembalaje y nivelación
Conexiones hidráulicas y eléctricas
Primer ciclo de lavado
Datos técnicos
Mantenimiento y cuidados, 16
Interrumpir el agua y la corriente eléctrica
Limpiar la lavadora
Limpiar el contenedor de detergentes
Cuidar la puerta y el cesto
Limpiar la bomba
Controlar el tubo de alimentación de agua
Precauciones y consejos, 17
Seguridad general
Eliminación
Descripción de la lavadora, 18-19
Panel de control
Pantalla
Cómo efectuar un ciclo de lavado, 20
Programas y opciones, 21
Tabla de programas
Opciones de lavado
Detergentes y ropa, 22
Contenedor de detergentes
Preparar la ropa
Programas particulares
Sistema de equilibrado de la carga
Anomalías y soluciones, 23
Asistencia Técnica, 24
FMG 823
Manual de instrucciones
14
ES
Instalación
! Es importante conservar este manual para
poder consultarlo en cualquier momento.
En caso de venta, de cesión o de traslado,
verifique que permanezca junto con la
lavadora para informar al nuevo propietario
sobre el funcionamiento y brindar las
correspondientes advertencias.
! Lea atentamente las instrucciones: ellas
contienen importante información sobre la
instalación, el uso y la seguridad.
Desembalaje y nivelación
Desembalaje
1. Desembale la lavadora.
2. Controle que la lavadora no haya sufrido
daños durante el transporte. Si estuviera
dañada no la conecte y llame al revendedor.
3. Quite los 3 tornillos
de protección
para el transporte
y la arandela
de goma con el
correspondiente
distanciador ubicados
en la parte posterior
(ver la figura).
4. Cubra los orificios con los tapones de
plástico suministrados con el aparato.
5. Conserve todas las piezas: cuando la
lavadora deba ser transportada nuevamente,
deberán volver a colocarse.
! Los embalajes no son juguetes para los
niños.
Nivelación
1. Instale la lavadora sobre un piso plano y
rígido, sin apoyarla en las paredes, muebles ni
en ningún otro aparato.
2. Si el piso no
está perfectamente
horizontal, compense
las irregularidades
desenroscando o
enroscando las patas
delanteras (ver la
figura); el ángulo de
inclinación medido
sobre la superficie
de trabajo, no debe
superar los 2º.
Una cuidadosa nivelación brinda estabilidad
a la máquina y evita vibraciones, ruidos y
desplazamientos durante el funcionamiento.
Cuando se instala sobre moquetas o
alfombras, regule los pies para conservar
debajo de la lavadora un espacio suficiente
para la ventilación.
Conexiones hidráulicas y
eléctricas
Conexión del tubo de alimentación de
agua
1. Conectar el tubo
de tubo enroscándolo
a un grifo de agua fría
con la boca roscada
de 3/4 gas (ver la
figura).
Antes de conectarlo,
haga correr el agua
hasta que esté
límpida.
2. Conecte el tubo
de alimentación
a la lavadora
enroscándolo en
la toma de agua
correspondiente
ubicada en la parte
posterior derecha
(arriba) (ver la figura).
3. Controle que en el tubo no hayan pliegues
ni estrangulaciones.
! La presión de agua del grifo debe estar
comprendida dentro de los valores contenidos
en la tabla de Datos técnicos (ver la página
correspondiente).
! Si la longitud del tubo de alimentación
no es la suficiente, diríjase a un negocio
especializado o a un técnico autorizado.
! No utilice nunca tubos ya usados.
! Utilice los suministrados con la máquina.
ES
15
Conexión del tubo de desagüe
Conecte el tubo de
desagüe, sin plegarlo,
a un conducto de
desagüe o a una
desagüe de pared
ubicados a una
distancia del piso
comprendida entre 65
y 100 cm.
Otra alternativa
es apoyar el tubo
de desagüe en
el borde de un
lavamanos o de una
bañera, uniendo la
guía (puesta a
disposición para la
venta por el servicio
de asistencia) al
grifo (ver la figura).
El extremo libre del tubo de desagüe no debe
permanecer sumergido en el agua.
! No se aconseja utilizar tubos de
prolongación, si fuera indispensable hacerlo,
la prolongación debe tener el mismo diámetro
del tubo original y no superar los 150 cm.
Conexión eléctrica
Antes de enchufar el aparato, verifique que:
• latomatengalaconexiónatierrayhaya
sido hecha según las normas legales;
• latomaseacapazdesoportarlacarga
máxima de potencia de la máquina
indicada en la tabla de Datos técnicos (ver
al costado);
• latensióndealimentaciónesté
comprendida dentro de los valores
indicados en la tabla de Datos técnicos (ver
al costado);
• latomaseacompatibleconelenchufedela
lavadora. Si no es así, sustituya la toma o el
enchufe.
! La lavadora no debe ser instalada al aire
libre, ni siquiera si el lugar está reparado, ya
que es muy peligroso dejarla expuesta a la
lluvia o a las tormentas.
! Una vez instalada la lavadora, la toma de
corriente debe ser fácilmente accesible.
! No utilice prolongaciones ni conexiones
múltiples.
! El cable no debe estar plegado ni sufrir
65 - 100 cm
compresiones.
! El cable de alimentación debe ser sustituido
sólo por técnicos autorizados.
¡Atención! La empresa fabricante declina toda
responsabilidad en caso de que estas normas
no sean respetadas.
Primer ciclo de lavado
Después de la instalación y antes del uso,
realice un ciclo de lavado con detergente y
sin ropa, seleccionando el programa “Auto
Limpieza” (ver “Limpiar la lavadora”).
Datos técnicos
Modelo
FMG 823
Dimensio-
nes
ancho 59.5 cm
altura 85 cm
profundidad 57.7 cm
Capacidad
de 1 a 8 kg
Conexiones
eléctricas
ver la placa de característi-
cas técnicas aplicada en la
máquina
Conexiones
hídricas
presión máxima
1 MPa (10 bar)
presión mínima
0,05 MPa (0,5 bar)
capacidad del cesto 54 litros
Velocidad de
centrifugado
máxima 1200 r.p.m.
Programas
de control
según las
reglamentos
1061/2010
1015/2010
programa 9;
Eco Algodón 60°C.
programa 9;
Eco Algodón 40°C.
Esta máquina cumple con lo
establecido por las siguien-
tes Directivas de la Comuni-
dad:
- EMC 2014/30/EU (Com-
patibilidad Electromagnética)
- 2012/19/EU - (WEEE)
- LVD 2014/35/EU (Baja
Tensión)
16
ES
Interrumpir el agua y la corriente
eléctrica
•Cierreelgrifodeaguadespuésdecada
lavado. De este modo se limita el desgaste
de la instalación hidráulica de la lavadora y
se elimina el peligro de pérdidas.
•Desenchufelamáquinacuandola
debe limpiar y durante los trabajos de
mantenimiento.
Limpiar la lavadora
•Laparteexternaylaspartesdegoma
se pueden limpiar con un paño embebido
en agua tibia y jabón. No use solventes ni
productos abrasivos.
•Lalavadoraposeeunprogramade“Auto
Limpieza” de su interior que se debe realizar
sin ningún tipo de carga en el cesto.
El detergente (en un
10% de la cantidad
aconsejada para
prendas poco sucias)
o algunos aditivos
específicos para la
limpieza de la ropa se
podrán utilizar como
coadyuvantes en el
programa de lavado.
Se aconseja efectuar
el programa de limpieza cada 40 ciclos de
lavado.
Para activar el programa pulse simultáneamente
los botones A y B durante 5 segundos
(ver la figura). El programa comenzará
automáticamente y tendrá una duración de 70
minutos aproximadamente. Para detener el ciclo
presione el botón START/PAUSE.
Limpiar el contenedor de
detergentes
Extraiga el contenedor
l e v a n t á n d o l o y
tirándolo hacia fuera
(ver la figura).
Lávelo debajo del agua
corriente, esta limpieza
s e d e b e re a l i z a r
frecuentemente.
Cuidar la puerta y el cesto
•Dejesiempresemicerradalapuertapara
evitar que se formen malos olores.
Mantenimiento y cuidados
Limpiar la bomba
La lavadora posee una bomba autolimpiante
que no necesita mantenimiento. Pero puede
suceder que objetos pequeños (monedas,
botones) caigan en la precámara que protege
la bomba, situada en la parte inferior de la
misma.
! Verifique que el ciclo de lavado haya
terminado y desenchufe la máquina.
Para acceder a la precámara:
1. quite el panel
que cubre la parte
delantera de la
lavadora con la ayuda
de un destornillador
(ver la figura);
2. desenrosque la
tapa girándola en
sentido antihorario
(ver la figura): es
normal que se
vuelque un poco de
agua;
3. limpie con cuidado el interior;
4. vuelva a enroscar la tapa;
5. vuelva a montar el panel verificando,
antes de empujarlo hacia la máquina, que
los ganchos se hayan introducido en las
correspondientes ranuras.
Controlar el tubo de alimentación de
agua
Controle el tubo de alimentación al menos
una vez al año. Si presenta grietas o rajaduras
debe ser sustituido: durante los lavados, las
fuertes presiones podrían provocar roturas
imprevistas.
! No utilice nunca tubos ya usados.
1
2
ES
17
Precauciones y consejos
! La lavadora fue proyectada y fabricada en conformidad
con las normas internacionales de seguridad. Estas
advertencias se suministran por razones de seguridad y
deben ser leídas atentamente.
Seguridad general
• Esteaparatohasidofabricadoparaunusodetipo
doméstico exclusivamente.
• Esteaparatopuedeserutilizadopor
niños de 8 años o más y por personas
con capacidades físicas, sensoriales o
mentales disminuidas o con experiencia y
conocimientos insuficientes siempre que
sean supervisados o que hayan recibido
una adecuada formación sobre el uso
del aparato en forma segura y conozcan
los peligros derivados del mismo. Los
niños no deben jugar con el aparato. El
mantenimiento y la limpieza no deben ser
realizados por niños sin supervisión.
• Lalavadoradebeserutilizadasóloporpersonas
adultas y siguiendo las instrucciones contenidas en este
manual.
• Notoquelamáquinaconlospiesdesnudosniconlas
manos o los pies mojados o húmedos.
• Nodesenchufelamáquinatirandoelcable,sino
tomando el enchufe.
• Noabraelcajóndedetergentesmientraslamáquina
está en funcionamiento.
• Notoqueelaguadedescargayaquepuedealcanzar
temperaturas elevadas.
• Enningúncasofuercelapuerta:podríadañarseel
mecanismo de seguridad que la protege de aperturas
accidentales.
• Encasodeavería,noaccedanuncaalosmecanismos
internos para intentar una reparación.
• Controlesiemprequelosniñosnoseacerquenala
máquina cuando está en funcionamiento.
• Duranteellavado,lapuertatiendeacalentarse.
• Sidebesertrasladada,deberánintervenirdosomás
personas, procediendo con el máximo cuidado. La
máquina no debe ser desplazada nunca por una sola
persona ya que es muy pesada.
• Antesdeintroducirlaropacontrolequeelcestoesté
vacío.
Eliminaciones
• Eliminacióndelmaterialdeembalaje:
respete las normas locales, de ese modo, los embalajes
podrán volver a ser utilizados.
• LanormaEuropea2012/19/EUsobrelaeliminación
de aparatos eléctricos y electrónicos, indica que los
electrodomésticos no deben ser eliminados de la
misma manera que los desechos sólidos urbanos. Los
aparatos en desuso se deben recoger separadamente
para optimizar el porcentaje de recuperación y
reciclaje de los materiales que los componen e impedir
potenciales daños para la salud y el medio ambiente. El
símbolo de la papelera tachada se encuentra en todos
los productos para recordar la obligación de recolección
separada.
Para mayor información sobre la correcta eliminación de
los electrodomésticos, los poseedores de los mismos
podrán dirigirse al servicio público responsable o a los
revendedores.
18
ES
Descripción de la lavadora
Panel de control
Botón
TEMPERATURA
MANDO DE
PROGRAMAS
Cajón de detergentes
Botón ON/OFF
Botón
CENTRIFUGADO
Botón y piloto
START/PAUSE
PANTALLA
Botón
COMIENZO
RETRASADO
Botones y pilotos
OPCIÓN
Cajón de detergentes: para cargar detergentes y
aditivos (ver “Detergentes y ropa”).
Botón ON/OFF : presione brevemente el botón para
encender o apagar la máquina. El piloto START/PAUSE
que centellea lentamente de color verde indica que la
máquina está encendida. Para apagar la lavadora durante
el lavado, es necesario mantener presionado el botón
durante más tiempo, aproximadamente 3 seg.; si se
presiona en forma más breve o accidental, la máquina no
se apagará. Si la máquina se apaga durante un lavado en
curso, dicho lavado se anulará.
MANDO DE PROGRAMAS: para seleccionar el
programa deseado (ver “Tabla de programas”).
Botones y pilotos OPCIÓN: para seleccionar las opciones
disponibles. El piloto correspondiente a la opción
seleccionada permanecerá encendido.
Botón ACCIÓN DE LIMPIEZA : pulse este botón
para seleccionar la intensidad de lavado deseada.
Botón TEMPERATURA : presiónelo para disminuir o
excluir la temperatura; el valor se indica en la pantalla.
Botón CENTRIFUGADO : presiónelo para disminuir o
excluir totalmente el centrifugado; el valor se indica en la
pantalla.
Botón COMIENZO RETRASADO : presiónelo
para seleccionar un comienzo retrasado del programa
previamente elegido; el retraso se indica en la pantalla.
Botón con piloto START/PAUSE: cuando el piloto
verde centellea lentamente, presione el botón para que
comience el lavado. Una vez que el ciclo ha comenzado,
el piloto se mantiene fijo. Para poner en pausa el lavado,
presione nuevamente el botón; el piloto centelleará con un
color anaranjado. Si el símbolo no está iluminado, se
podrá abrir la puerta (3 minutos aproximadamente). Para
que el lavado se reanude a partir del momento en el cual
fue interrumpido, presione nuevamente el botón.
Botón BLOQUEO DE BOTONES: para activar el
bloqueo del panel de control, mantenga presionado
el botón durante 2 segundos aproximadamente. El
símbolo encendido indica que el panel de control
está bloqueado (con excepción del botón ON/OFF).
De este modo, se evitan modificaciones accidentales
de los programas, sobre todo si en la casa hay niños.
Para desactivar el bloqueo del panel de control,
mantenga presionado el botón durante 2 segundos
aproximadamente.
Modalidad de stand by
Esta lavadora está en conformidad con las nuevas
normativas vinculadas al ahorro energético. Está
dotada de un sistema de auto-apagado (stand by)
que, en caso de no funcionamiento, se activa pasados
aproximadamente 30 minutos. Presionar brevemente el
botón ON/OFF y esperar que la máquina se active.
Botón
ACCIÓN DE
LIMPIEZA
Botón
BLOQUEO
DE
BOTONES
ES
19
Pantalla
La pantalla es útil para programar la máquina y ofrece múltiple información.
En la sección A se visualiza la duración de los distintos programas disponibles, para los que han comenzado, el tiempo que
falta para su finalización (la pantalla muestra la duración máxima del ciclo seleccionado, que puede disminuir después de
unos minutos, ya que la duración efectiva del programa varía según la carga de ropa y los ajustes elegidos); si se hubiera
seleccionado un COMIENZO RETRASADO, se visualiza el tiempo que falta para que comience el programa seleccionado.
Además, presionando el botón correspondiente, se visualizan los valores máximos de la velocidad de centrifugado y de
temperatura que la máquina puede alcanzar en base al programa seleccionado o los últimos valores seleccionados si son
compatibles con el programa elegido.
En la sección B se visualizan las “fases de lavado” previstas para el ciclo seleccionado y, una vez comenzado el programa, la
“fase de lavado” en curso:
Lavado
Aclarado
Centrifugado
Descarga
En la sección C se encuentran, comenzando desde la izquierda, los iconos correspondientes a la “temperatura”, al
“centrifugado” y al “Comienzo retrasado”.
Las barras de “temperatura” indican el nivel de temperatura con respecto al máximo que se puede seleccionar para
el ciclo elegido.
Las barras de “centrifugado” indican el nivel de centrifugado con respecto al máximo que se puede seleccionar para
el ciclo elegido.
El símbolo “COMIENZO RETRASADO” iluminado indica que en la pantalla se visualiza el valor del “Comienzo retrasado” fijado.
Piloto Puerta bloqueada
El símbolo encendido indica que la puerta está bloqueada. Para evitar daños, antes de abrir la puerta espere que el símbolo
se apague (3 minutos aproximadamente). Para abrir la puerta mientras un ciclo está en curso, presione el botón START/
PAUSE; si el símbolo PUERTA BLOQUEADA está apagado, será posible abrir la puerta (3 minutos aproximadamente).
B
C
A
20
ES
Cómo efectuar un ciclo de lavado
1. ENCENDER LA MÁQUINA. Presione el botón ; el
piloto START/PAUSE centelleará lentamente de color
verde.
2. CARGAR LA ROPA. Abra la puerta. Cargue la ropa,
cuidando no superar la cantidad de carga indicada en la
tabla de programas de la página siguiente.
3. DOSIFICAR EL DETERGENTE. Extraiga el cajón y
vierta el detergente en las cubetas correspondientes
como se explica en “Detergentes y ropa”.
4. CERRAR LA PUERTA.
5. ELEGIR EL PROGRAMA. Seleccione con el mando
PROGRAMAS el programa deseado; al mismo están
asociadas una temperatura y una velocidad de
centrifugado que se pueden modificar. En la pantalla
aparecerá la duración del ciclo.
6. PERSONALIZAR EL CICLO DE LAVADO. Utilice los
correspondientes botones:
Modificar la temperatura y/o el centrifugado.
La máquina muestra automáticamente la temperatura
y la centrifugación máximas previstas para el programa
fijado o las últimas seleccionadas si son compatibles
con el programa elegido. Presionando el botón
se disminuye progresivamente la temperatura hasta
llegar al lavado en frío “OFF”. Presionando el botón
se disminuye progresivamente el centrifugado hasta
su exclusión “OFF”. Si se presionan una vez más los
botones, se volverá a los valores máximos previstos.
! Excepción: cuando se selecciona el programa 4, la
temperatura se puede aumentar hasta 90°C.
Seleccionar un comienzo retrasado.
Para seleccionar el comienzo retrasado del programa
elegido, presione el botón correspondiente hasta
alcanzar el tiempo de retraso deseado. Cuando
dicha opción está activada, en la pantalla se ilumina
el símbolo . Para cancelar el comienzo retrasado
presione el botón hasta que en la pantalla aparezca
“OFF”.
Seleccionar la intensidad de lavado deseada.
La opción permite optimizar el lavado en base al
grado de suciedad de los tejidos y a la intensidad de
lavado deseada.
Seleccione el programa de lavado, el ciclo
automáticamente se fija en el nivel “Normal” optimizado
para prendas medianamente sucias (selección no válida
para el ciclo “Lana” que se fija automáticamente en el
nivel “Delicate”).
Para prendas muy sucias, pulse el botón hasta
alcanzar el nivel “Intensive”. Este nivel garantiza un
lavado de grandes prestaciones gracias al uso de una
mayor cantidad de agua en la fase inicial del ciclo y
un mayor movimiento mecánico. Es útil para eliminar
las manchas más resistentes. Puede emplearse con o
sin lejía.Si se desea realizar un blanqueo, introduzca la
cubeta adicional 4 suministrada con la máquina, en la
cubeta 1. Al verter el blanqueador, no supere el nivel
“max” indicado en el perno central (ver la figura de la
pág. 22).
Para prendas poco sucias o para un tratamiento
más delicado de los tejidos, pulse el botón hasta
alcanzar el nivel “Delicado”. El ciclo disminuirá el
movimiento mecánico para garantizar resultados
perfectos de lavado para las prendas delicadas.
Modificar las características del ciclo.
• Presioneelbotónparaactivarlaopción;elpiloto
correspondiente al botón se encenderá.
• Presionenuevamenteelbotónparadesactivarla
opción; el piloto se apagará.
! Si la opción seleccionada no es compatible con el
programa elegido, el piloto centelleará y la opción no se
activará.
! Si la opción seleccionada no es compatible con
otra precedentemente seleccionada, el piloto
correspondiente a la primera función seleccionada
centelleará y se activará solo la segunda, el piloto de la
opción activada se iluminará.
! Las opciones pueden variar la carga recomendada y/o
la duración del ciclo.
7. PONER EN MARCHA EL PROGRAMA. Presione
el botón START/PAUSE. El piloto correspondiente se
iluminará de color azul fijo y la puerta se bloqueará
(símbolo PUERTA BLOQUEADA encendido). Para
cambiar un programa mientras un ciclo está en curso,
ponga la lavadora en pausa presionando el botón
START/PAUSE (el piloto START/PAUSE centelleará
lentamente de color ámbar); luego seleccione el ciclo
deseado y presione nuevamente el botón START/
PAUSE.
Para abrir la puerta mientras un ciclo está en curso,
presione el botón START/PAUSE; si el símbolo PUERTA
BLOQUEADA está apagado, será posible abrir
la puerta (3 minutos aproximadamente). Presione
nuevamente el botón START/PAUSE para reanudar
el programa a partir del momento en el que se había
interrumpido.
8. FIN DEL PROGRAMA. Se indica con el mensaje
“END” en la pantalla, cuando el símbolo PUERTA
BLOQUEADA se apague, será posible abrir la
puerta (3 minutos aproximadamente). Abra la puerta,
descargue la ropa y apague la máquina.
! Si se desea anular un ciclo ya comenzado, presione largo
tiempo el botón . El ciclo se interrumpirá y la máquina se
apagará.
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
