Hotpoint TCD 971 6CY1 (EU) Guida utente

Marca: Hotpoint

Modello: TCD 971 6CY1 (EU)

Tipo: Guida utente

First time you turn on your dryer

you must select your preferred

language see Display

English, 1

Contents

Installation, 2

Warnings, 4

Care and Maintenance, 6

Control Panel, 8

Laundry, 8

The Display, 9

Start and Programmes, 11

Troubleshooting, 15

Assistance, 16

TUMBLE DRYER

TCD 971

Instruction booklet

! This symbol reminds you to read this

instruction manual.

! Keep this manual at hand for immediate reference whenever

necessary. Always store this manual close to the tumble dryer and

remember to pass it on to any new owners when selling or tran-

sferring the appliance, so they may familiarise with the warnings

and suggestions herein contained.

! Read these instructions carefully: the following pages contain

important information on installation and useful suggestions for

operating the appliance.

www.hotpoint.eu

Italiano, 33

Ελληνικά, 17

Where to put your dryer

• Place your dryer at a

distance from gas ranges,

stoves, heaters, or cooktops

because flames can damage

the appliance. The dryer

should be installed in an

ambient room temperature

of between 20 to 23°C

for optimum performance.

But will function if the room is between 14 and

30°C. If you are going to install the appliance

under a work counter, be sure to leave a 10 mm

space between the top and any other objects

on or above the machine and a 15 mm space

between the sides and lateral furnishings or

walls. This is to ensure proper air circulation.

The appliance must be installed with the rear

surface placed against a wall.

Ventilation

• When the dryer is in use, there has to be

adequate ventilation. Make sure you put your dryer

in an environment that is not damp and has proper

air circulation throughout. Airflow around the dryer

is essential to condense the water produced during

the washing, the dryer will not operate efficiently in

an enclosed space or cupboard.

! If using the dryer in a small or cold room

some condensation will be experienced.

We do not recommend that the dryer is

installed in a cupboard but the dryer must never

be installed behind a lockable door, a sliding

door or a door with a hinge on the opposite

side to that of the dryer door.

H<1m

Fig. A Fig. B

Water Drain

If the machine is positioned close to a drain it is possible to drain the

condensed water directly without using the waterbottle. In which

case it is no longer necessary to empty the water bottle at the end

of each cycle. If the Dryer is positioned above or close to a Washing

Machine the same drainage can be used. Just remove the tube

indicated in figure A and connect it to the drainage. If the drainage

is further away than the length of the tube it is possible to buy and

connect a tube of the same diameter and the necessary length in

order to reach the drain. To install the new tube just substitute the

existing one as indicated in figure B inserting it in the same place.

! The drain tube has to be below 1 m from the bottom of

the Dryer.

! Once the Dryer has been installed please assure that

the drain tube is not bent or kinked.

Electrical connections

Before plugging the appliance into the socket,

check the following:

• Make sure your hands are dry.

• The socket must have an earth connection.

• The socket must be able to withstand

the machine’s maximum power output as

indicated on the rating plate.

• The power supply voltage must fall within

the values indicated on the data plate.

• The socket must be compatible with the

dryer’s plug. Should this not be the case,

replace the plug or the socket.

! DO NOT USE EXTENSION CORDS.

! The dryer must not be installed outdoors,

even if the space is sheltered. It can be very

dangerous if exposed to rain or storms.

! Once installed, the dryer’s electrical wire and

plug must be within reach.

! The power cord must not be bent or

squashed.

! If the plug being replaced is a non-rewirable

type, then the cut-off plug must be disposed of

safely. DO NOT leave it where it can be inserted

into a socket and create a shock hazard.

! The power must be regularly checked. If the

supply cord is damaged, it must be replaced

by the manufacturer, its service agent or

similarly qualified persons in order to avoid

a hazard. (see Assistance). New or longer

electric cords are supplied by authorised

dealers at a supplementary cost.

! The manufacturer denies any

responsibility should any of these rules

not be followed.

! If in doubt about any of the above

consult a qualified electrician.

Levelling the tumble dryer

The dryer must be installed level for correct

operation.

When you have installed your dryer in its final

location check that it is level first side-to-side,

then front to back. If the dryer is not level,

Installation

10 mm

15 mm

This household tumble drier is a Condenser

The weighted Annual Energy Consumption (AEc)* kWh 1) 340.0

This household tumble drier is a Automatic

Energy consumption full load; Edry - kWh 2) 2.85

Energy consumption partial load; Edry½ - kWh 2) 1.56

Power consumption: off-mode (Po) - Watts 0.14

Power consumption: left-on mode (Pl) - Watts 3.36

Prog. Time - weighted (Tt) full & partial load - minutes 3) 197

Full load (Tdry) - minutes 261

Partial load (Tdry½) - minutes 149

weighted (Ct) full & partial load 3) 81

full load (Cdry) 81

partial load (Cdry½) 81

Airborne acoustical noise emissions - dB(A) re 1 pW 70

Average condensation efficiency - %

the information in the label and the fiche relates. The standard cotton program is

suitable to dry at cupboard level (0%) cotton laundry and is the most efficient

programme in terms of energy consumption. Partial load is half the rated load.

2) based on 160 drying cycles of the standard cotton programme at full and

partial load, and the consumption of the low-power modes. Actual energy

consumption will depend on how the appliance is used.

3) Weighted average of 3 cycles at full load and 4 cycles at half load.

Regulation 932/2012.

0.68

Energy efficiency class on a scale from A+++ (low

consumption) to D (high consumption)

A+

Duration of the 'left-on mode' for power management system -

minutes

Condensation efficiency class on a scale from G (least efficient)

to A (most efficient)

Product Data - Regulation 392/2012.

Brand

HOTPOINT/ARISTON

Model

TCD 971 6CY1 (EU)

Rated capacity of cotton laundry for the "standard cotton

programme" at full load - kg

9.0

Maximum load sizes: 9 kg

adjust the two legs up or down until your

dryer is level.

Preliminary information

Once you’ve installed your dryer and before you use it, clean

the inside of the drum to remove any dust that could have

accumulated during transportation.

Warning ! Before you use your dryer ensure that its has

been in a upright position for at least 6 hours.

Warnings

! This appliance has been designed and built

according to international safety standards.

These warnings are given for safety reasons

and must be followed carefully.

General safety

• This appliance can be used by children

aged from 8 years and above and

persons with reduced physical, sensory or

mental capabilities or lack of experience

and knowledge if they have been given

supervision or instruction concerning use of

the appliance in a safe way and understand

the hazards involved.

• This tumble dryer has been designed for

home, and not professional, use.

• Do not touch the appliance while barefoot

or with wet hands or feet.

• Unplug the machine by pulling on the plug,

not the cord.

• After using the dryer, turn it off and unplug

it. Keep the door closed to make sure that

children do not use it as a toy.

• Children should be supervised to ensure

that they do not play with the dryer.

• Cleaning and user maintenance shall not be

made by children without supervision.

•Children of less than 3 years should be

kept away from the appliance unless

continuously supervised.

• The appliance must be installed correctly

and have proper ventilation. The air intake

at the front of the dryer should never be

obstructed (see Installation).

• Never use the dryer on carpeting where

the pile height would prevent air from

entering the dryer from the base.

• Check to see if the dryer is empty before

loading it.

•

The back of the dryer could become

very hot. Never touch it while in use.

•

Do not use the dryer unless the filter,

watercontainer and condenser are securely in

place (see Maintenance).

• Do not overload the dryer (see Laundry for

maximum loads).

• Do not load items that are dripping wet.

• Carefully check all instructions on clothing

labels (see Laundry).

• Do not tumble dry large, very bulky items.

• Do not tumble dry acrylic fibres at high

temperatures.

• Do not turn off the dryer when there are still

warm items inside.

• Clean the filter after each use (see

Maintenance).

• Empty the Water Container after each use

(see Maintenance).

• Clean the Heat Pump filter unit at regular

intervals (see Maintenance).

• Do not allow lint to collect around the dryer.

• Never climb on top of the dryer. It could

result in damage.

• Always follow electrical standards and

requirements (see Installation).

• Always buy original spare parts and

accessories (see Service).

To minimise the risk of fire in your tumble

dryer, the following should be observed:

• Tumble dry items only if they have been

washed with detergent and water, rinsed and

been through the spin cycle. It is a fire hazard

to dry items that HAVE NOT been washed

with water.

• Do not dry garments that have been treated

with chemical products.

• Do not tumble dry items that have been

spotted or soaked with vegetable or cooking

oils, this constitutes a fire hazard. Oil-affected

items can ignite spontaneously,especially

when exposed to heat sources such as

a tumble dryer. The items become warm,

causing an oxidisation reaction with the

oil, Oxidisation creates heat. If the heat

cannot escape, items can become hot

enough to catch fire. Piling, stacking or

storing oil-effected items can prevent heat

from escaping and so create a fire hazard.

If it is unavoidable that fabrics containing

vegetable or cooking oil or those that have

been contaminated withhair care products

be placed in a tumble dryer they should first

be washed with extra detergent - this will

reduce, but not eliminate the hazard. They

should not be removed from the dryer and

piled or stacked while hot.

• Do not tumble dry items that have previously

been cleaned in or washed in, soaked in

or soiled with petrol/gasoline, dry cleaning

solvents or other flammable or explosive

substances. Highly flammable substances

commonly used in domestic environments

including cooking oil, acetone, denatured

alcohol, kerosene, spot removers, turpentine,

waxes and wax removers. Ensure these

items have been washed in hot water with

an extra amount of detergent before being

dried in the tumble dryer.

• Do not tumble dry items containing foam

rubber (also known as latex foam), or

similarly textured rubber like materials.

Foam rubber materials can, when heated,

produce fire by spontaneous combustion.

• Fabric softener or similar products should

not be used in a tumble dryer to eliminate

the effects of static electricity unless the

practice is specifically recommended by

the manufacturer of the fabric softener

product.

• Do not tumble dry undergarments that

contain metal reinforcements eg. bras

with metal reinforcing wires. Damage to

the tumble dryer can result if the metal

reinforcements come loose during drying.

• Do not tumble dry rubber, plastic articles

such as shower caps or babies waterproof

covers, polythene or paper.

• Do not tumble dry rubber backed articles,

clothes fitted with foam rubber pads,

pillows, galoshes and rubber coated tennis

shoes.

• 

Remove all objects from pockets such as

lighters and matches.

! WARNING: Never stop the dryer before

the end of the drying cycle unless all

items are quickly removed and spread

out so that the heat is dissipated.

Save energy and respect the environment

• Wring out all items to eliminate excess water before

tumble drying (if you use a washing machine first, select

a high spin cycle). Doing this will save time and energy

during drying.

• Always dry full loads - you save energy: single items or

small loads take longer to dry.

• Clean the filter after each use to contain energy

consumption costs (see Maintenance).

Disconnecting the power supply

! Disconnect the dryer when not in use or

during cleaning and maintenance operations.

Cleaning the filter after each cycle

The filter is a fundamental component of the

dryer: its function is to collect lint and fluff that

form during drying.

Clean the filter once

drying is completed, by

rinsing it under running

water or cleaning it

with a vacuum cleaner.

Should the filter become

clogged, the flow of air

inside the dryer will be

seriously hampered:

drying times becomes

longer and more energy

is consumed. Moreover,

the dryer may become

damaged.

The filter is located in

front of the dryer seal

(see Picture).

Removing the filter:

1. Pull the filter’s plastic handle upwards (see

Picture).

2. Clean the fluff off the filter and replace it

correctly. Ensure that the filter is pushed fully

home.

! Do not use the dryer unless the filter has

been replaced in its holder.

Checking the drum after each cycle

Rotate the drum manually to remove smaller items

(handkerchiefs) that could have been left inside the dryer.

Cleaning the drum

! Avoid using abrasives, steel wool or stainless steel cleaning

agents to clean the drum. A coloured film may appear on the

stainless steel drum surface: it may be caused by a combina-

tion of water and/or cleaning agents such as wash-softeners.

This coloured film does not affect the dryer’s performance.

Emptying the water container after each

cycle

Remove the water container and

empty it into a sink or other

suitable drain outlet, then

replace it correctly.

Always check the water

container and empty it before

starting a new drying cycle.

-Failure to empty the water container may cause the

following:

- The dryer stops heating (thus the load may still be

damp at the end of the drying cycle).

Priming the Water Collection System

When your dryer is new, the Water Container will not

collect Water until the system is primed, this will take

1 or 2 drying cycles. Once primed it will collect Water

during every cycle.

Cleaning the Heat Pump Filter Unit

• Periodically (every 5 drying cycles) remove

Heat pump filter unit and clean any build up

of fluff from the surface of the filter by rinsing

it under running water or with your vacuum

cleaner.

We however recommend that you clean this

filter after every drying cycle to optimize the

dryers performance.

To remove Heat pump

filter unit:

1. Unplug the dryer and

open the door.

2. Remove the filter unit

by rotating the 4 clips

to the vertical position

then pulling the filter

unit towards you.

3. Separate the two

parts of the filter unit and clean the surface of

the filter.

! Warning: The front of

the heat pump is made

from thin metal plates.

Take care that you do

not damage these or cut

yourself when cleaning,

removing or replacing

the filter unit.

4.Whenever you clean the Heat pump filter

unit always clean any build up of fluff from

Care and maintenance

the surface of the metal

plates. Carefully clean

this fluff off with a damp

clot

h,sponge or vacuum

cleaner. Never use your

Fingers.

5. Assemble the two

parts of the filter clean

the surface of the

seals and replace with the 4 clips into the

horizontal position, sure that the catches

have been secured.

Cleaning the tumble dryer

• The external metal, plastic and rubber parts can be

cleaned with a damp cloth.

• Clean the front air intake grille regularly (every 6 months)

with a vacuum cleaner to remove any lint, fluff or dust

deposits. Furthermore, remove any lint deposits from the

front part of the Heat pump filter unit and from the filter

area, using a vacuum cleaner every so often.

! Do not use solvents or abrasives.

! Have the dryer checked regularly by authorised technical

personnel in order to ensure that the electrical and

mechanical parts work safely (see Assistance).

Water container

Heat pump

filter unit

Cover

Catches

Filter

Handle

Air intake

Heat Pump Protection System

The heat pump system has a compressor protection

feature that operates if you open the door or there is a

power disruption or if you turn off the dryer. This system

will prevent the heat pump compressor from starting for

5 minutes after the door is closed and the programme is

started.

Quick Tips

!Remember to clean your filter and Heat

Pump filter unit after each load.

! Remember to empty your water container

after each load.

! Doing this will keep your machine working

at its BEST!

Model & Serial numbers

Rating plate

Adjustable feet

Control panel

PROGRAMME

Selection Buttons

Display Unit

ON/OFF

Button

CHILD LOCK &

OPTIONS

Buttons & Lights

START/PAUSE

Button & Light

The ON/OFF button : - if pressed when the dryer is

running: If the display shows

TURNING OFF

the dryer

stops. If the display shows

PRESS AND HOLD

, hold the

botton and the display counts down 3, 2, 1 and then stops.

Press and hold again for more than 3 seconds, the display

brieﬂ y shows

POWER ON

The PROGRAMME selection buttons set the programme:

press the button corresponding to the programme you

want to select (see Start and Programmes).

The OPTION buttons/indicators: these buttons select

available options for your selected programme (see The

Controls). The indicators on the display unit next to the

bottom buttons light to show that the option has been

selected.

The START/PAUSE button/light

starts a selected

programme. When a programme is running, pressing this

button in pauses the programme, there will be one beep,

the display will show

PAUSE

and the dryer stops.

The light is green when the programme is running, ﬂ ashing

Sorting laundry

• Check the symbols on the care labels of the various gar-

ments to verify whether the garments can be safely tumble

dried.

• Sort laundry according to the type of fabric.

• Empty all pockets and check for loose buttons.

• Close zips and hooks and fasten belts and strings without

tightening them.

• Wring out garments to remove the maximum amount of

water possible.

Do not load the dryer when garments are dripping wet.

Maximum load sizes

Do not overload the drum.

The following values indicate the weight of dry garments:

Natural fibres: maximum kg

Synthetic fibres: maximum kg

Laundry

amber if the programme has been paused or ﬂ ashing

green if on standby waiting to start a programme (see

Start and Programmes).

Note: This light also ﬂ ashes amber during the Post

Care phase of a programme.

The Display Unit gives warnings and information about

the programme selected and its progress (see next page).

The CHILD LOCK button/icon

: Press and hold this

button after selecting your programme and any options,

this prevents the programme settings from being changed,

the display will brieﬂ y show

LOCKED

. When the icon

is lit, the other buttons are disabled. Hold the button to

cancel and the icon will go out, the display will brieﬂ y show

UNLOCKED

Note: This tumble dryer, in compliance with new energy

saving regulations, is ﬁ tted with an automatic standby

system which is enabled after about 30 minutes if no

activity is detected. Press and hold the ON-OFF button

until the display brieﬂ y shows

POWER ON

, and the dryer

then reactivates.

! Do not overload the dryer as this may result is reduced

drying performance.

Care labels

Always check the care labels, especially when placing

garments in the tumble dryer for the first time. Below are the

most commonly used symbols:

May be tumble dried.

Do not tumble dry.

Tumble dry – high heat.

Tumble dry – low heat.

The Display

Selecting your language

The ﬁ rst time you turn on your dryer you should select your preferred language from the available list.

Understanding the display

Programme selection and display

The selected programme is shown on the ﬁ rst line of the display, this message is shown while the programme is running.

Eight of the buttons have two selections, press the button once for the ﬁ rst choice and press again for the second choice, your

selected programme is displayed. The ﬁ nal button selects My Cycle.

My Cycle. When you select the My Cycle button the Display will show your selected programme with ‘M’ before its

name. ie.

M STANDARD COTTON (see Start and Programmes).

Dryness levels

During programme selection for an automatic programme that has different dryness levels available (see Programmes

Table).

The second line of the display shows the dryness level you require, for each press of the

Dryness Level button the next

option from the list below is selected and displayed. The display also shows 1 to 7 bars depending on your selection and

these are displayed during the programmes progress.

! Some automatic programmes do not allow the dryness level to be changed or do not have all the dryness level options.

To change: the language current selection must ﬂ ash, on the ﬁ rst

line of the display.

- Press the On/Off button to turn off the display then press and hold

all 3 buttons:

Heat Level, Timed Dry, and Sensor Dry

for 5 seconds.

- Press the

Heat Level or the Timed Dry button to scroll up

or down through the list.

- When your required language is ﬂ ashing on the top line of the

display, pressing the

Sensor Dry button will select your choice.

DAMP

IRON DRY

HANGER PLUS

HANGER DRY

LIGHT DRY

CUPBOARD DRY

EXTRA DRY

Dries your items ready to be ironed using a machine or rotary ironer.

Dries your items ready to be ironed with a hand iron.

Dries your delicate items ready to be hanged for ﬁ nal drying.

Dries your items ready to be hanged for ﬁ nal drying.

Dries your delicate items ready to be put away.

Dries your items ready to be put away.

Dries your clothes ready to be worn.

Programme progress

The second line of the display shows the status of the programme as it progresses:

(long messages scroll across the line)

(if option Crease Care selected)

DRY

COOL TUMBLE

HEATING

READY

END OF CYCLE, CREASE CARE

END OF CYCLE, CLEAN FILTER AND EMPTY WATER BOTTLE

The Display

Timed drying

After selecting a programme that has a Timed Dry

option, press the

Timed button and the display will

increment the selected time, each time you press and

release the button (see Start and Programmes).

Delay and Time to End

Some programmes can have a delayed start

(see Start and Programmes). Press the

Delay button and the icon ﬂ ashes.

Each press of the Delay button

advances

the delay setting in 1 hour increments, from:

,then and then after a couple of

seconds cancels the delay.

The delay time is shown on the display next to the Delay button.

The display counts down the minutes of the delay period after the Start/Pause button

is pressed. The second line of the

display shows

STARTS IN

You can change or cancel the delay time selected anytime if you wish.

After the Start/Pause button is pressed the Delay or Time to End is displayed in hours and minutes and counts down each

minute.

Time to End

After the delay period ﬁ nishes, or for all the programme if delay not selected, this part of the display will show:

- the estimated time to the end of the programme, for automatic programmes

- the actual time remaining during a timed programme

When timed programmes are selected the time displayed throughout the cycle is the actual time remaining.

When Automatic programmes are selected the time displayed is an estimate of the time remaining. When the programme is

selected the display shows the time required to dry a full load. The time remaining is constantly monitored during the drying

cycle and is updated to show the best forecast.

The colons between the hours and minutes in the display ﬂ ash to show the time is counting down.

Each press reduces the time duration and number of available time options depending on the programme/material

selected.

The Timed Dry icon

is displayed next to the time..

The selected time remains displayed after the programme starts, but can be changed anytime you wish.

My Cycle button:

First time you press this button the display will show

PRESS AND HOLD TO STORE

After selecting your favorite programme and options you can save these settings by pressing and holding in the My Cycle

button for at least 5 seconds, the top line will show a ﬂ ashing M followed by the selected programme. The

buzzer will then beep and the second line of the display shows

MEMORY

The next time you need this programme press the M, button, then the Start/Pause button (and this programme will run.

If you wish, you can change your stored favorite, by selecting a new programme and/or options and press and hold

in the M button (as above).

Choosing a programme

1. Plug the dryer into the electrical socket.

2. Sort your laundry according to fabric type (see Laundry).

3. Open the door and make sure the ﬁ lter is clean and in

place and the water container is empty and in place (see

Maintenance).

4. Load the machine and make sure items are not in the way

of the door seal. Close the door.

5. If the Display is not lit: Press the ON/OFF button .

6. Press the Programmes Selection button that corresponds

with the type of fabric being dried by checking the

Programmes Table (see Programmes) as well as the

indications for each type of fabric (see Laundry).

- if the M button is selected; steps 7 and 8 are not required

(see below).

7. Choose Timed Drying or Dryness Levels option:

- If Timed Drying press and release the Timed button until

the required time is displayed

or - To change from default dryness setting, press and

release the Dryness Levels button until required level is

indicated.

! See Programmes Table, for more details: availability of

Dryness Levels, Timed Dry and Options.

8.Set a delay time and other options if necessary (see The

Display).

Start and Programmes

9.Press the Start/Pause button to begin. The display

will show the estimated time to end. During the drying

programme, you can check on your laundry and take out

items that are dry while others continue drying. When you

close the door again, press the Start/Pause button

order to resume drying.

If you open the door to check your laundry you will extend

the drying time as the heat pump compressor will not start for

5 minutes after you close the door and press the Start/Pause

button (see The Controls).

10. During the last few minutes of Drying Programmes,

before the programme is completed, the ﬁ nal COOL

TUMBLE phase is entered (fabrics are cooled), this phase

should always be allowed to complete.

11. At the end of the drying cycle a message is displayed:

- if

END OF CYCLE, CLEAN FILTER AND EMPTY WATER BOTTLE

is shown, the buzzer will beep 3 times (Note: If the SOUND

option was selected the buzzer beeps 3 times every 30

seconds for 5 minutes).

- if

END OF CYCLE, CREASE CARE

is shown, Crease Care

option has been selected and if you do not remove the

laundry immediately, the dryer will tumble occasionally for 10

hours or until you open the door, the buzzer will beep 3 times

to conﬁ rm the programme is completed.

12. Open the door, take the laundry out, clean the ﬁ lter and

replace it. Empty the Water Container and replace it (see

Maintenance).

13. Unplug the dryer.

Drying times

Drying times are approximate and may vary depending on the following:

• Amount of water retained by items after the spin cycle: towels and delicate items retain a lot of water.

• Fabrics: items of the same fabric, but with different texture and thickness may have different drying times.

• Amount of laundry: single items and small loads may take longer to dry.

• Drying: if items are to be ironed, they can be removed from the dryer while still slightly damp. Items that require complete

drying can be left longer.

• Heat setting.

• Temperature of the room: the lower the temperature of the room, the longer it will take for the dryer to dry clothing.

• Bulk: certain bulky items require special care during the drying process. We suggest removing these items and replacing them

in the dryer once they have been shaken out: repeat this procedure several times during the course of the drying cycle.

! Do not over-dry items.

All fabrics contain natural dampness which helps to keep them soft and ﬂ uffy.

The drying times provided refer to the automatic Cupboard dry programmes.

The Timed drying settings are also indicated to enable you to select the most suitable timed option.

The weight refers to dry items.

n° Programme

Description of program

The duration of the drying cycles can be checked on the display

Standard

Cotton

• This is a programme for cotton items.

• The Standard Cotton programme to EU Regulation 392/2012 is Programme 1 selection with High Heat and Dryness Level

Cupboard Dry (the standard/default starting configuration). It is the most efficient programme in terms of energy consumption

(to EU.392/2012).

max

Shirts

Cottons

• This is a programme for shirts made from cotton.

• Loads dried using the Cupboard Dry setting are usually ready to wear, the edges or seams may be slightly damp. If this

is the case, try turning the shirts inside out and running the programme again for a short period.

3 kg

Bed & Bath

• This is a programme for cotton towels and sheets.

• Loads dried using the Extra Dry setting are usually ready to use, the edges or seams may be slightly damp especially on

large items. If this is the case, try opening them out and running the programme again for a short period.

max

Anti

Allergy

• This programme has the ‘Seal of Approval’ endorsement from Allergy UK, which reflects the effective reduction and

elimination of allergens from the clothes with the special Anti Allergy cycle. With this programme, thanks to the achie-

vement of constant temperature for an extended period of time, the effects of the most common allergens (including

House Mites and Pollen) are neutralised.

• Can be used on a full size wet load to dry and treat, or on a 4 kg dry load just to treat your laundry. If the display shows

CLEAN FILTER TO ENSURE ANTI ALLERGY ACTION

: Clean the filter and re-start the programme.

max or 4 kg

Synthetics

• This is a programme for items of Synthetic with low heat setting or Synthetic/Cotton mixtures with medium heat setting.

3 kg

Shirts

Sytnthetic

• This is a programme for shirts made from synthetic materials or a mixture of natural and synthetic materials, such as

polyester and cotton.

• Loads dried using the Cupboard Dry setting are usually ready to wear, the edges or seams may be slightly damp. If this

is the case, try turning the shirts inside out and running the programme again for a short period.

3 kg

Jeans

• This is a programme for jeans made from denim cotton. Before drying your jeans turn the front pockets inside out.

• Do not mix dark and light coloured items.

• It can also be used on other garments made from the same material, such as jackets.

• Loads dried using the Extra Dry setting are usually ready to wear, the edges or seams may be slightly damp. If this is the

case, try turning the jeans inside out and running the programme again for a short period.

! We do not recommend that you use this programme if your jeans have elastic waist bands, studs or embroidery.

3 kg

Duvet

! Take care with this programme DO NOT dry any items that are damaged which could result in the filling blocking the filter

and air vent resulting in a fire hazard.

• Must only be used on single size duvets: NOT suitable for double or king size items.

• Loads dried using this programme are usually ready to use, but may be slightly damp in places. If this is the case, try

opening them out and shaking them and running the programme again for a short period.

• Also suitable for down filled jackets.

• Select high heat for Cotton Duvets and medium heat for Synthetic duvets.

Note:

1 - The duration of the program will depend on the size of the load, types of textiles, the spin speed used in your washer and any extra options

selected.

Note:

1 - The duration of the program will depend on the size of the load, types of textiles, the spin speed used in your washer and any extra options

selected.

n° Programme

Description of program

The duration of the drying cycles can be checked on the display

Wool

• This is a programme for tumble dryer safe garments marked with the symbol

• We recommend that garments are turned inside out before drying.

• Loads dried using this programme are usually ready to wear, but on some heavier garments the edges may be slightly

damp. Allow these to dry naturally as over-drying could damage garments.

! Unlike other materials, the mechanism of wool shrinkage is irreversible; i.e. it will not stretch back to original size and shape.

! This programme is not suitable for Acrylic garments.

1 kg

Silk

• This is a programme for drying your delicate silk.

• Loads dried using the Cupboard Dry setting are usually ready to use, but on some garments the edges may be slightly

damp. If this is the case, try opening them out or turn items inside out and running the programme again for a short

period.

0,5 kg

Delicates

• This is a programme for drying your delicate clothes ie. Acrylics.

• Loads dried using this programme are usually ready to wear, but on some heavier garments the edges may be slightly

damp. If this is the case, try turning items inside out and running the programme again for a short period.

2 kg

Baby

• This is a programme for drying your baby’s small delicate items of clothing and bedding (Cotton and Chenille) and for

drying your delicate clothes.

• DO NOT dry items such as bibs and nappy pants with plastic coverings.

• Loads dried using this programme are usually ready to wear, but on some heavier garments the edges may be slightly

damp. If this is the case, try turning items inside out and running the programme again for a short period.

2 kg

Cuddly Toy

• With this programme you can remove dust easier and wash the cuddly toys more often because the drying time is very

much reduced compared to drying in the open air. It is a delicate drying cycle that dries at low temperature and with soft

mechanical action to maintain at best the original look and shine of the fur.

Note: For allergy protection, just freeze cuddly toys for 24 hours then wash and dry them. Repeat every 6 weeks.

• Before drying remove accessories such as clothes, collars or sound boxes and protect plastic eyes with masking tape

after drying them with a cloth.

• The programme time will vary dependant on the exact make up of the load. The maximum load should not exceed 2.5

kg and no individual item should be greater than 600 g.

2,5 kg

Heat & Enjoy

• This programme helps to heat towels & bathrobes for a warm sensation after a bath or shower. It is also useful for warming

clothes before dressing during winter. The cycle heats clothes to 37°C (Body Temperature), the display shows

HEATING

and runs at this temperature for a maximum of 4 hours or until you stop the cycle by opening the door when the display

shows

READY

Note: The Start/Pause button is disabled during this programme.

3 kg

Refresh

! ‘Refresh’ is not a drying programme and should not be used for wet articles of clothing.

• It can be used on any load size, but is more effective on smaller loads.

• Do not overload your dryer (see Laundry).

• This is a 20 minute programme that airs your clothes with cool air. Also use to cool warm clothes.

Pre Iron

• ‘Pre Iron’ is a treatment cycle for use with dry clothes and reduces creases in order to facilitate ironing and folding, it has a

maximum duration of 15 minutes.

! ‘Pre Iron’ is not a drying programme and should not be used for wet articles of clothing.

• For best results:

1. Do not load more than the maximum capacity. These numbers refer to the dry weight: (Fabric-Maximum load) Cotton and

Cotton mixtures-2.5 kg; Synthetics-2 kg; Denim-2 kg.

2. Unload the dryer immediately after the end of the programme, hang, fold or iron the articles and put them away in the closet.

Should this not be possible repeat the programme.

2,5 kg

The Controls

! Warning, after pressing the START/PAUSE button ,

the programme cannot be changed. To change a selected

programme, press the START/PAUSE button

the light

flashes Amber to indicate the programme is paused. Select

the new programme and any options required, the light will

then flash green. Press the START/PAUSE button

again

and the new programme will start.

• Option buttons

These buttons serves to personalise the selected

programme according to personal requirements.

Not all options are available for all programmes.

Some options are incompatible with the ones

previously set. If the button of any unavailable option

is pressed, the buzzer will beep 3 times. If the option

is available, the option light will stay on.

Delay Timer (Time Delay)

The start of some programmes (see The Display and

Programmes tables) can be delayed for up to 24 hours.

Ensure the water container is emptied before setting a

delayed start.

Crease Care

The pre-care option is only available if a delayed start has

been selected. It tumbles the clothes occasionally during

the delayed period to help prevent creases developing. The

post-care option occasionally tumbles the clothes after end

of the drying and cool tumble cycles to prevent creases

developing, should you not be available to remove the load

immediately the programme is complete

Note: The START/PAUSE

light flashes Amber during

this phase. Selecting this option enables both the pre and

post care functions if appropriate.

Heat Level button, Display and Icons

Not all programmes allow you to change the heat level and

some programmes allow all three heat level options:

Low, Medium and High.

When the heat level options are available pressing this

button changes the heat level and the display briefly shows

the selected heat level, along with a display of the selected

level icon:

HIGH HEAT

MEDIUM HEAT

LOW HEAT

Extra Care

This Anti-Ageing function for Cottons helps to maintain the

brightness of your laundry for a long time, thanks to the

correct drum rotation (reduced in the last part of the cycle)

and the correct temperature.

Less Tangled

This option has the drum movement modified to give a

tumbling action that reduces tangling and knotting of your

clothes. The Less Tangled option gives best results when

used with smaller loads.

Ready to Iron

This option allows you to dry loads where only some of the

items need ironing and you do not wish to fully dry those

items. When Iron Dry level is reached, a buzzer sounds to let

you know that the items that need ironing can be removed.

The dryer then stops and the START/PAUSE light flashes

orange. Remove the items you wish to iron, close the

door and press the START/PAUSE button

, the dryer

continues until the remaining items reach the selected dryness

level. It can be used for load sizes up to 3kg.

• TIME DISPLAY

The display shows either the amount of time delay remaining or

an indication of the amount of time left for a drying programme

(see The Display). The display also shows if there is a problem

with your dryer, if this occurs the display will show F followed by

a fault code number (see Troubleshooting).

• Empty Water Container

(Messages about emptying can be ignored if you have plumbed

your dryer into a drain as there is no need to empty the water

container). Messages are displayed to reminds you to empty

the water container (see The Display). If the water container fills

during a programme, the heater turns off and the dryer does a

period of Cool Tumble. After this it stops and a message tells

you to

EMPTY THE WATER CONTAINER

. You must empty the water

container and restart the dryer or the clothes will not dry. After

re-starting the dryer the message will take a few seconds to go

out. To avoid this always empty the water container each time

you use the dryer (see Maintenance).

• Door Opening

Opening the door during a programme will stop the dryer and

have the following effects:

Note: The START/PAUSE

light flashes Amber during the

Post Care phase of a programme

 • The display shows

PAUSED

• During a delay phase the delay will continue to count down.

The START/PAUSE

button must be pressed to resume

the delay programme. The display will change to show current

status.

• The START/PAUSE

button must be pressed to resume

the programme. The display will change to show the

current status.

• During the Post Care phase, the programme ends. Pressing

the START/PAUSE

button will restart a new programme

from the beginning.

• Note

If you have a power cut, switch off the power or remove the

plug. When power is restored, press and hold the On/Off

button until the display briefly shows

POWER ON

and the dryer

reactivates. Then press the START/PAUSE

button and the

programme will resume.

Troubleshooting

Possible causes / Solution:

• The plug is not plugged into the socket, or not making contact.

• There has been a power failure.

• The fuse has blown. Try to plug another appliance into the socket.

• You are using an extension cord? Try to plug the dryer’s power cord directly into the

socket.

• The door is not closed securely?

• The programme has not been set properly (see Start and Programmes).

• The Start/Pause button has not been pressed (see Start and Programmes).

• You have set a delayed time (see Start and Programmes).

• The filter has not been cleaned (see Maintenance).

• The water container needs emptying? The empty water message is displayed? (see

Maintenance).

• The heat pump filter needs cleaning? (see Maintenance).

• The temperature setting is not ideal for the type of fabric you are drying (see Start

and Programmes, and see Laundry).

• The correct drying time has not been selected for the load (see Laundry).

• The air intake grille is obstructed (see Installation, and see Maintenance).

• The items were too wet (see Laundry).

• The dryer was overloaded (see Laundry).

•

The water container was probably not emptied at the start of the programme. Do not

wait for the empty water signal, always check and empty the container before starting

a new drying programme (see Maintenance).

• This is normal, the:

message is shown as a reminder to empty the container (see The Display and Start

and Programmes).

! For safety the dryer has a maximum programme time of 5 hours. If an automatic

programme has not sensed the required final moisture in this time the dryer will

complete the programme and stop. Check the above points and run the programme

again, if the results are still damp, contact the Service Centre (see Service).

• If the display shows a fault:

- Turn off and remove the plug. Clean the filter and the heat pump filter unit (see

Maintenance). Then replace the plug, turn on and start another programme. If a fault

is then displayed: Note down the code and contact the Service Centre (see Service).

• The dryer is in ‘Demo’ mode. Press and hold both the On/Off and Start/Pause

buttons for 3 seconds. The display will show

DEMO OFF

for 3 seconds and then the

dryer will resume normal operation.

• The dryer has gone into standby mode to save power. This occurs if you have had a

power cut or leave your dryer either without starting a programme or after your drying

programme has finished.

- Press and hold the On/Off button and the lights will come on.

Problem:

The tumble dryer won’t start.

Drying cycle will not begin.

Its taking a long time to dry.

Empty water message is displayed but

the dryer has only been running for a

short period.

Empty water message is displayed and

the water container is not full.

Programme finishes and clothes are

damper than expected.

The display shows a fault

code F followed by one or two

numbers.

The display briefly shows

DEMO ON

every 6 seconds.

The lights on the dryer control

panel are off although the

dryer is switched on.

One day your dryer seems not to be working. Before you call your Service Centre (see Service), go through the following

troubleshooting suggestions:

END OF CYCLE, CLEAN FILTER AND EMPTY THE WATER BOTTLE

Service

Information on recycling and disposal

As part of our continual commitment towards environmental protection, we reserve the right to use recycled quality components

to reduce costs for our customers and to minimise materials wastage.

• Disposing of the packaging materials: follow local regulations to allow for recycling of packaging materials.

• In order to minimise the risk of injury to children, remove the door and plug, then cut the power supply cord flush with the

appliance. Dispose of these parts separately to prevent the appliance from being connected to a power supply socket.

Disposal of old household appliances

The European Directive 2012/19/EC on Waste Electrical and Electronic Equipment (WEEE), requires that old household

electrical appliances must not be disposedof in the normal unsorted municipal waste stream. Old appliances must be

collected separately in order tooptimise the recovery and recycling of the materialsthey contain and reduce the impact on

human healthand the environment. This dryer has a sealed heat pump unit containing Fgases which should be recovered

and destroyed.The crossed out “wheeled bin” symbol on theproduct reminds you of your obligation,thatwhen you dispose of

the appliance it must beseparately collected.Consumers should contact their local authority orretailer for information concer-

ning the correct disposalof their old appliance.

This appliance has been designed, constructed and distributed in compliance with the

requirements of European Directives:

- LVD 2014/35/EU, EMC 2014/30/EU and RoHS 2011/65/EU.

Heat Pump System

This dryer is fitted with a sealed heat pump system to dry

your clothes. To operate, the heat pump contains fluorinated

greenhouse gases ( F gases) which are covered by the Kyoto

Protocol. These F gases are contained in a hermetically

sealed unit. This sealed unit contains kg of the F gas

R134a which acts as a refrigerant. GWP = 1430 (0.4 t C02).

If the sealed unit fails then it must be replaced by a new

sealed unit. Contact your nearest service centre for advise.

Note: The gases contained in the sealed unit are not

hazardous to health, but if they escape they will have an

impact on global warming.

Before calling the Service Centre:

• Use the troubleshooting guide to see if you can solve the

problem yourself (see Troubleshooting).

• If not, turn off the dryer and call the Service Centre closest to

you.

Spare Parts

This dryer is a complex machine. Repairing it yourself or

having a nonauthorised person try to repair it could cause

harm to one or more persons and to the machine, and could

invalidate the spare parts warranty.

Call an authorised technician if you experience problems

while using the machine.

Please note that it is an offence for an unqualified person

to undertaken any servicing or repair work that involves

breaking into the sealed heat pump unit.

What to tell the Service Centre:

• Name, address, and post code;

• telephone number;

• the type of problem;

• the date of purchase;

• the appliance model (Mod.);

• the dryer serial number (S/N).

This information can be found on the data label inside the

door of the machine.

0,29

Contents

Εγκατάσταση, 18

Προειδοποιήσεις, 20

Φροντίδα και συντήρηση, 22

Πίνακας χειρισμού - Μπουγάδα, 24

Η Οθόνη, 25

Εκκίνηση και προγράμματα, 27

Προβλήματα και λύσεις, 31

Υποστήριξη, 32

TCD 971

Οδηγίες χρήσης

ΣΤΕΓΝΩΤΗΡΙΟ

! Το σύμβολο αυτό σου θυμίζει να

διαβάζεις αυτό το εγχειρίδιο οδηγιών.

! Να διατηρείτε εύχερα το παρόν εγχειρίδιο ώστε να μπορείτε

να το συμβουλεύεστε εύκολα οποτεδήποτε. Να διατηρείτε το

εγχειρίδιο πλησίον του στεγνωτηρίου. Στην περίπτωση που η

συσκευή πωληθεί ή παραχωρηθεί σε άλλα άτομα, θυμηθείτε να

τους παραδώσετε αυτό το εγχειρίδιο, ώστε να μπορούν και οι

νέοι κάτοχοι να γνωρίζουν τις προειδοποιήσεις και τις υποδείξεις

για τη χρήση του στεγνωτηρίου.

! Διαβάστε προσεκτικά αυτές τις οδηγίες: οι σελίδες που

ακολουθούν περιέχουν σημαντικές πληροφορίες για την

εγκατάσταση και χρήσιμες υποδείξεις για τη λειτουργία της

οικιακής ηλεκτρικής συσκευής.

www.hotpoint.eu

Την πρώτη φορά που

θα ενεργοποιήσετε το

στεγνωτήριο σας πρέπει

να επιλέξετε την επιθυμητή

γλώσσα βλ. Η Οθόνη

Ελληνικά

Που εγκαθίσταται το στεγνωτήριο

• Οι φλόγες μπορεί να

προξενήσουν ζημιές

στο στεγνωτήριο, που

πρέπει να εγκατασταθεί

μακριά από κουζίνες

αερίου, θερμάστρες,

καλοριφέρ ή πλαίσια

μαγειρέματος.

Το στεγνωτήριο πρέπει

να εγκατασταθεί σε ένα

χώρο με θερμοκρασία μεταξύ των 20 και 23

°C για να έχετε τις βέλτιστες επιδόσεις. Σε

κάθε περίπτωση, η σωστή λειτουργία είναι

εγγυημένη μεταξύ των 14 και 30°C.

Αν η ηλεκτρική συσκευή πρέπει να

εγκατασταθεί κάτω από έναν πάγκο

εργασίας πρέπει να αφήσετε ένα χώρο 10

mm μεταξύ του επάνω πάνελ της ηλεκτρικής

συσκευής και άλλων αντικειμένων

ευρισκόμενων πάνω από αυτό και ένα χώρο

15 mm μεταξύ των πλευρών της ηλεκτρικής

συσκευής και των τοιχωμάτων ή των

γειτονικών σε αυτό επίπλων. Με τον τρόπο

αυτό διασφαλίζεται επαρκής κυκλοφορία

αέρα.

Η συσκευή πρέπει να εγκατασταθεί με την

πίσω επιφάνεια τοποθετημένη κόντρα σε

τοίχο

Αερισμός

• Όταν το στεγνωτήριο είναι ενεργό πρέπει να υπάρχει

επαρκής αερισμός. Βεβαιωθείτε ότι εγκαθιστάτε το

στεγνωτήριο σε χώρο χωρίς υγρασία και που διαθέτει

κατάλληλη κυκλοφορία αέρα. Η ροή αέρα πέριξ του

στεγνωτηρίου είναι βασική για να επιτραπεί η συμπύκνωση

του παραγόμενου νερού κατά το πλύσιμο. Το στεγνωτήριο

δεν λειτουργεί σωστά αν

τοποθετηθεί σε χώρο κλειστό ή

στο εσωτερικό ενός επίπλου.

! Αν το στεγνωτήριο χρησιμοποιείται σε μικρό ή κρύο

δωμάτιο μπορεί να δημιουργηθεί λίγο συμπύκνωμα.

! Δεν προτείνεται η εγκατάσταση του

στεγνωτηρίου σε ντουλάπι. Η οικιακή

ηλεκτρική συσκευή δεν πρέπει ποτέ να

εγκαθίσταται πίσω από πόρτα που κλείνει

με κλειδί, από συρόμενη πόρτα ή από

πόρτα με μεντεσέ στο πλευρό το αντίθετο

της πόρτας του στεγνωτηρίου.

Άδειασμα του νερού

Αν η μηχανή τοποθετηθεί πλησίον ενός σωλήνα

αποστράγγισης μπορεί να εκρεύσει το συμπύκνωμα νερού

απ’ ευθείας χωρίς να χρειαστεί να χρησιμοποιήσετε το

δοχείο συλλογής του νερού. Στην περίπτωση αυτή δεν

απαιτείται πλέον να αδειάζετε το δοχείο συλλογής νερού

μετά από κάθε κύκλο.

Αν το στεγνωτήριο τοποθετηθεί πάνω ή δίπλα σε

πλυντήριο

μπορεί να μοιράζεται το ίδιο σύστημα

αποστράγγισης. Αρκεί να αποσυνδέσετε το σωλήνα

που φαίνεται στην εικόνα A και να τον συνδέσετε στην

αποστράγγιση.

Αν το άδειασμα βρίσκεται πιο μακριά από το μήκος του

σωλήνα, για να το φτάσετε μπορείτε να αποκτήσετε και να

συνδέσετε ένα σωλήνα ίδιας διαμέτρου και του

αναγκαίου

μήκους.

Για να εγκαταστήσετε το νέο σωλήνα αρκεί να

αντικαταστήσετε τον υπάρχοντα όπως υποδεικνύεται στην

εικόνα B εισάγοντάς τον στην ίδια θέση.

! Η αποστράγγιση πρέπει να βρεθεί 1 m χαμηλότερα σε

σχέση με τη βάση του στεγνωτηρίου.

! Αφού εγκαταστήσετε το στεγνωτήριο βεβαιωθείτε ότι ο

σωλήνας αποστράγγισης δεν είναι διπλωμένος κι ούτε

τυλιγμένος.

Εικ. A Εικ. B

Ηλεκτρική σύνδεση

Πριν εισάγετε το βύσμα στην ηλεκτρική

πρίζα ελέγξτε τα ακόλουθα:

• Βεβαιωθείτε ότι τα χέρια είναι στεγνά.

• Η πρίζα πρέπει να διαθέτει γείωση.

• Η πρίζα πρέπει να είναι σε θέση να

αντέχει την μέγιστη προβλεπόμενη ισχύ

για τη μηχανή, που αναφέρεται στην

πινακίδα των στοιχείων λειτουργίας

(βλέπε Περιγραφή του στεγνωτηρίου).

• Η τάση τροφοδοσίας πρέπει να κυμαίνεται

στις τιμές που υποδεικνύονται στην

πινακίδα των δεδομένων λειτουργίας (

βλέπε Περιγραφή του στεγνωτηρίου).

• Η πρίζα πρέπει να είναι συμβατή με

τον τύπο βύσματος του στεγνωτηρίου.

Σε διαφορετική περίπτωση, προβείτε

στην αντικατάσταση της πρίζας ή του

βύσματος.

! ΜΗ ΧΡΗΣΙΜΟΠΟΙΕΊΤΕ ΠΡΟΕΚΤΆΣΕΙΣ.

! Το στεγνωτήριο δεν μπορεί να

εγκατασταθεί σε χώρους εξωτερικούς,

ακόμη και προφυλαγμένους. Πράγματι,

μπορεί να είναι πολύ επικίνδυνο να

Εγκατάσταση

10 mm

15 mm

H<1m

Μέγιστο μέγεθος φορτίου: 9kg

Αυτό το οικιακό στεγνωτήριο είναι Αυτόματο

Ενεργειακή κατανάλωση πλήρους φορτίου. Edry- kWh 2) 2.85

Ενεργειακή κατανάλωση μερικού φορτίου. Edry½,- kWh 2) 1.56

Κατανάλωση ισχύος: Εκτός λειτουργίας (Po) - Watts 0.14

Κατανάλωση ισχύος: Κατάσταση αναμονής (Pl) - Watts 3.36

Πλήρες φορτίο (Tdry) - λεπτά 261

Μερικό φορτίο (Tdry½) - λεπτά 149

σταθμισμένο (Ct) πλήρες και μερικό φορτίο 3) 81

Πλήρες φορτίο Cdr 81

Μερικό φορτίο Cdry½ 81

Συνθετικά: Ενεργειακή κατανάλωση πλήρους φορτίου. kWh 0.68

Συνθετικά: Πλήρες φορτίο - λεπτά 70

κανονισμό 932/2012.

Συνθετικά: Μερικό φορτίο Μ/Ε

Μέση απόδοση συμπύκνωσης - %

Εκπομπές αερόφερτου ακουστικού θορύβου - dB(A) re 1 pW

1) Το "τυπικό πρόγραμμα βαμβακερών" με πλήρες και μερικό φορτίο και το " τυπικό

πρόγραμμα βαμβακερών " μερικού φορτίου είναι τα τυπικά προγράμματα στα οποία

αναφέρονται οι πληροφορίες στην ετικέτα και στην καρτέλα. Τα προγράμματα αυτά

είναι κατάλληλα για πλήρες στέγνωμα (0%) βαμβακερών και είναι τα πιο

αποτελεσματικά προγράμματα με όρους κατανάλωσης ενέργειας. Το μερικό φορτίο

είναι το μισό του πλήρους φορτίου.

2) Ετήσια κατανάλωση βασισμένη σε 160 κύκλους στεγνώματος του τυπικού

προγράμματος βαμβακερών σε πλήρες και μερικό φορτίο, και κατανάλωση των

καταστάσεων λειτουργίας σε χαμηλή ισχύ. Η πραγματική κατανάλωση ενέργειας

ανά κύκλο θα εξαρτάται από τον τρόπο χρήσης της συσκευής. **Το Τυπικό

Πρόγραμμα Βαμβακερών

3) Μέσο βάρος 3 κύκλων πλήρους φορτίου και 4 κύκλοι μισού φορτίου.

Διάρκεια της κατάστασης αναμονής για σύστημα διαχείρισης

ισχύος - λεπτά

Πρόγρ. Σταθμισμένος χρόνος (Tt) πλήρους και μερικού φορτίου-

λεπτά 3)

197

Τάξη απόδοσης συμπύκνωσης σε κλίμακα από το G (ελάχιστη

απόδοση) έως το Α (μέγιστη απόδοση)

Αυτό το οικιακό στεγνωτήριο είναι

Συμπυκνωτής

Τάξη ενεργειακής απόδοσης σε κλίμακα από A+++ (χαμηλή

κατανάλωση) έως D (υψηλή κατανάλωση)

A+

Η σταθμισμένη Ετήσια Κατανάλωση Ενέργειας (AEc)* Kwh 1)

340.0

Στοιχεία Προϊόντος - κανονισμό 392/2012

εμπορικό σήμα·

HOTPOINT/ARISTON

μοντέλου

TCD 971 6CY1 (EU)

Διαβαθμισμένη χωρητικότητα πλυμένων βαμβακερών για το

τυπικό πρόγραμμα βαμβακερών σε πλήρες φορτίο - kg

9.0

εκθέσετε την ηλεκτρική αυτή συσκευή στη

βροχή ή σε κακοκαιρία.

! Μετά την εγκατάσταση του στεγνωτηρίου

το ηλεκτρικό καλώδιο και το βύσμα πρέπει

να είναι ευχερή.

! Το ηλεκτρικό καλώδιο δεν πρέπει να

διπλώνει κι ούτε να τσαλακώνει.

! Αν το βύσμα προς αντικατάσταση

είναι ενσωματωμένου τύπου, πρέπει να

το διαθέσετε με τρόπο ασφαλή. ΜΗΝ

το αφήνετε εκεί που θα μπορούσε να

εισαχθεί σε μια πρίζα και να προκαλέσει

ηλεκτροπληξίες.

! Το ηλεκτρικό καλώδιο θα πρέπει να

ελέγχεται περιοδικά. Αν το καλώδιο

τροφοδοσίας είναι χαλασμένο, θα πρέπει να

αντικατασταθεί από τον κατασκευαστή, από

την υπηρεσία του τεχνικής υποστήριξης ή

από άλλο ειδικευμένο επαγγελματία για την

αποσόβηση κινδύνων. (βλέπε Υποστήριξη).

Τα νέα ή τα μακρύτερα ηλεκτρικά καλώδια

παρέχονται από τους εξουσιοδοτημένους

μεταπωλητές με πρόσθετο κόστος.

! Ο κατασκευαστής αποποιείται κάθε

ευθύνης όταν δεν τηρούνται οι κανόνες

αυτοί.

! Σε περίπτωση αμφιβολίας σχετικά με

τα παραπάνω, επικοινωνήστε με έναν

ειδικευμένο ηλεκτρολόγο.

Ισοστάθμιση του στεγνωτηρίου

Το στεγνωτήριο πρέπει να εγκατασταθεί

οριζόντια για να λειτουργήσει σωστά.

Αφού εγκαταστήσετε το στεγνωτήριο στην

οριστική θέση, ελέγξτε την ισοστάθμισή του

πρώτα από πλευρά σε πλευρά και στη συνέχεια

από εμπρός με πίσω.

Αν το στεγνωτήριο δεν είναι ισοσταθμισμένο,

ρυθμίστε τα δύο εμπρόσθια ποδαράκια προς τα

επάνω ή τα κάτω, μέχρι να οριζοντιοποιηθεί.

Προκαταρκτικές πληροφορίες

Αφού εγκατασταθεί το στεγνωτήριο, πριν το θέσετε

σε λειτουργία καθαρίστε το εσωτερικό του κάδου και

απομακρύνετε τη βρωμιά που μπορεί να συσσωρευτεί κατά

τη μεταφορά.

! Η συσκευή έχει σχεδιαστεί και

κατασκευαστεί σύμφωνα με τα διεθνή

πρότυπα ασφαλείας. Οι προειδοποιήσεις

αυτές παρέχονται για λόγους ασφαλείας και

πρέπει να τηρούνται με προσοχή.

Γενική ασφάλεια

• Το παρόν στεγνωτήριο μπορεί

να χρησιμοποιείται από άτομα

(συμπεριλαμβανομένων των παιδιών

από 8 ετών και άνω) με μειωμένες

ικανότητες φυσικές, αισθητηριακές ή

νοητικές ή χωρίς εμπειρία και γνώση, αν

επιτηρούνται ή δέχονται οδηγίες σχετικές

με τη χρήση της συσκευής από άτομο

υπεύθυνο για την ασφάλειά τους.

• Το στεγνωτήριο αυτό έχει σχεδιαστεί για

οικιακή και όχι για επαγγελματική χρήση.

• Μην αγγίζετε τη συσκευή όταν είστε

ξυπόλητοι ή έχετε βρεγμένα χέρια ή πόδια.

• Όταν βγάζετε τη συσκευή από την πρίζα,

τραβάτε το ρευματολήπτη (φις) και όχι το

καλώδιο.

• Μετά τη χρήση, απενεργοποιήστε το

στεγνωτήριο και βγάλτε το από την

πρίζα. Κρατάτε την πόρτα κλειστή για

να βεβαιωθείτε ότι τα παιδιά δεν θα τη

χρησιμοποιούν σαν παιχνίδι.

• Τα παιδιά δεν πρέπει να μένουν χωρίς

επίβλεψη, ώστε να διασφαλίζεται ότι δεν

παίζουν με το στεγνωτήριο.

• Καθαρισμός και συντήρηση δεν πρέπει να

εκτελούνται από παιδιά χωρίς επιτήρηση.

• Τα παιδιά ηλικίας μικρότερης των 3 ετών

θα πρέπει να κρατιούνται σε απόσταση

από το στεγνωτήριο εκτός κι αν

επιτηρούνται συνεχώς.

• Η συσκευή πρέπει να εγκαθίσταται σωστά

και να αερίζεται επαρκώς. Η είσοδος αέρα

στη μπροστινή όψη του στεγνωτηρίου

δεν πρέπει να φράσσεται ποτέ. (βλ.

Εγκατάσταση).

• Ποτέ μην χρησιμοποιείτε το στεγνωτήριο

επάνω σε χαλιά όπου το ύψος του πέλους

μπορεί να εμποδίζει την είσοδο του αέρα

στο στεγνωτήριο από τη βάση.

• Ελέγξτε αν το στεγνωτήριο είναι άδειο

πριν το γεμίσετε.

• Το πίσω μέρος του στεγνωτηρίου

μπορεί να ζεσταθεί πολύ. Ποτέ μην το

αγγίζετε την ώρα που λειτουργεί.

• Μη χρησιμοποιείτε το στεγνωτήριο

εάν το φίλτρο, ο περιέκτης νερού και ο

συμπυκνωτής δεν έχουν στερεωθεί καλά

στη θέση τους (βλ. Συντήρηση).

• Μην υπερφορτώνετε το στεγνωτήριο (βλ.

Πλύσιμο ρούχων) για μέγιστα φορτία.

•

Μην βάζετε στο στεγνωτήριο πλυμένα

ρούχα που στάζουν.

• Ελέγξτε προσεκτικά όλες τις οδηγίες

στις ετικέτες των ρούχων (βλ. Πλύσιμο

ρούχων).

• Μην στεγνώνετε μεγάλα, πολύ ογκώδη

είδη.

• Μην στεγνώνετε ακρυλικά υφάσματα σε

υψηλές θερμοκρασίες.

• Μην απενεργοποιείτε το στεγνωτήριο ενώ

περιέχει ακόμη ζεστά ρούχα.

• Καθαρίζετε το φίλτρο μετά από κάθε

χρήση (βλ. Συντήρηση).

• Εκκενώνετε τον περιέκτη νερού μετά από

κάθε χρήση (βλ. Συντήρηση).

• Καθαρίζετε τη αντλία θερμότητας

ανά τακτά χρονικά διαστήματα (βλ.

Συντήρηση).

• Μην αφήνετε να συγκεντρώνεται χνούδι

γύρω από το στεγνωτήριο.

• Ποτέ μην ανεβαίνετε επάνω στο

στεγνωτήριο, μπορεί να προκαλέστε βλάβη.

• Πάντα να τηρείτε τα ηλεκτρικά πρότυπα

και τις προδιαγραφές (βλ. Εγκατάσταση).

• Πάντα να αγοράζετε γνήσια ανταλλακτικά

και αξεσουάρ (βλ. Τεχνική υποστήριξη).

Για να ελαχιστοποιηθεί ο κίνδυνος

πυρκαγιάς στο στεγνωτήριο σας,

θα πρέπει να προσέχετε τα εξής:

• Βάζετε στο στεγνωτήριο ρούχα μόνο αν

έχουν πλυθεί με απορρυπαντικό και νερό,

έχουν ξεπλυθεί και στυφτεί. Υπάρχει

κίνδυνος πυρκαγιάς αν στεγνώνετε ρούχα

που ΔΕΝ έχουν πλυθεί με νερό.

• Μην στεγνώνετε ρούχα που έχουν

υποβληθεί σε χημικά προϊόντα.

• Μη στεγνώνετε ρούχα που έχουν

λερωθεί ή εμποτιστεί με ελαιόλαδο ή

λάδι μαγειρικής, γιατί υπάρχει κίνδυνος

πυρκαγιάς. Τα λαδωμένα αντικείμενα

μπορεί να αναφλεγούν αυτόματα,

ιδιαίτερα όταν εκτίθενται σε πηγές

θερμότητας όπως το στεγνωτήριο. Τα

αντικείμενα ζεσταίνονται και προκαλούν

μια αντίδραση οξείδωσης με το λάδι,

η οποία προκαλεί θερμότητα. Αν η

θερμότητα δεν μπορεί να διαφύγει, τα

αντικείμενα ενδέχεται να θερμανθούν

σε επίπεδο πρόκλησης πυρκαγιάς.

Η στοίβαξη ή η φύλαξη λαδωμένων

αντικειμένων μπορεί να εμποδίσει τη

Προειδοποιήσεις

La pagina sta caricando ...

Hotpoint TCD 971 6CY1 (EU) Guida utente

Marca: Hotpoint

Modello: TCD 971 6CY1 (EU)

Tipo: Guida utente

Scarica il pdf

rapporto

in altre lingue

English: Hotpoint TCD 971 6CY1 (EU) User guide

Hotpoint TCD 971 6CY1 (EU) Guida utente

Hotpoint TCD 971 6CY1 (EU) Guida utente

in altre lingue

Documenti correlati

Altri documenti