Installation instructions:

Ultra High Capacity Under Sink

Direct Connect Water Filtration System

Installation Instructions

Model: AQ-5KDC-S

Step 1:

Turn off the cold water valve and turn on the faucet to

ensure that there is no residual water.

Flow rate ....................................................................................................................................................................................................................................................................5.5 lpm/1.5 gpm

Operating specifications:

Storage and maintenance:

- Replace your filter every 12 months or 5,000 gallons to achieve optimal performance and prevent bacteria and fungus growth in your filter

and supply lines.

- Keep your unused filters in a cool, dark, and dry place until you need them.

Step 2:

Remove the cold water hose from the cold water valve.

Step 3:

Connect the 3/8" or 1/2”female compression end of the

inlet hose to the cold water valve. Connect the other end

of the inlet hose to the filter inlet. (The inlet is on the cap

Step 5:

Select the proper fittings to fix the filter.

Option 1-Bracket: Select the proper position on the cabinet wall.

Install the bracket and then push the filter into the bracket.

Option 2-Cable tie mounts: Take out 4 cable tie mounts and

select the proper position for pasting them. Thread the cable ties

into the cable tie mounts and fix the filter.

Step 6:

Turn on the cold water valve to flush the filter for 5 minutes. Check

for any leakage.

responsibility or liability for damages arising out of misuse of the product.

*The service life mentioned above is subject to chlorine reduction.

Actual result varies according to the local water quality.

Cable tie mount

water valve or inlet hose, remove the hoses and confirm whether the connection gasket is installed in place, or wrap Teflon tape on

the external thread. If the water leakage is at the connections between the hoses and the filter, make sure that the hoses are inserted

to the end and that the inserted length is about 4/5".

Q: Does the filter have to be replaced every 12 months?

A: Yes, we recommend that the filter be replaced every 12 months. If the filter is overused, bacteria may grow in it and affect the

water quality. If the water flow slows down or if many impurities are deposited in the filtration system, the filter may need to be

replaced sooner. The service life will vary based on the condition of your water.

Q: Does the filter need to be flushed after installation?

A: Yes, we recommend that you turn on the faucet and flush the filter for 5 minutes after installation. The filter media contains

Uwaga:

Rozmiar zaworu zimnej wody i potrzebna armatura.

- Jeżeli wylot zaworu kątowego ma rozmiar 3/8",

można go podłączyć bezpośrednio do źródła wody.

Wylot 3/8"

- Jeżeli wylot zaworu kątowego ma rozmiar 1/2", można go podłączyć za pomocą dwóch następujących złączek.

Połącz do węża

Opcja 1-Uchwyt: Wybierz odpowiednie miejsce na ścianie szafy,

zamontuj uchwyt, a następnie wciśnij do niego filtr.

Opcja 2-Mocowania opasek kablowych: Wyjmij 4 uchwyty na

opaski kablowe i wybierz odpowiednią pozycję do ich wklejenia.

Włóż opaski kablowe do uchwytów i zamocuj filtr.

Krok 6:

Włącz zawór zimnej wody, aby przepłukać filtr przez 5 minut

Sprawdź, czy nie występują wycieki.

Option 1

Option 2

Anweisungen zum Einbau:

Schritt 1:

Drehen Sie das Kaltwasserventil ab und drehen Sie den Wasserhahn

Schritt 2:

Ziehen Sie den Kaltwasserschlauch vom

Instructions d'installation:

Étape 1:

Fermez le robinet d'eau froide et ouvrez le robinet pour

Étape 2:

Retirez le tuyau d'eau froide du robinet d'eau froide.

Stap 1:

Draai de koudwaterkraan dicht en tum op de kraan om

Stap 2:

Verwijder de koudwaterslang van de koudwaterkraan.

Steg 1:

Stäng av kallvattenventilen och tumma på kranen för att

Steg 2:

Ta bort kallvattenslangen från kallvattenventilen.

Steg 4: Anslut 3/8 "eller 1/2" hankompressionsänden på

utloppsslangen till kranslangen. Anslut den andra änden av

utloppsslangen till filterutloppet.

Kurulum talimatları:

1. Adım:

Soğuk su vanasını kapatın ve su kalmadığından emin

2. Adım:

Soğuk su borusunu soğuk su vanasından çıkarın.

4. Adım:

Çıkış borusunun 3/8" veya 1/2" erkek sıkıştırma ucunu musluk

hortumuna bağlayın. Çıkış hortumunun diğer ucunu filtre

Bu filtre, sistemden önce veya sonra yeterli dezenfeksiyon yapılmadan mikrobiyolo-

jik olarak güvenli olmayan veya kalitesi bilinmeyen sularla birlikte kullanılmamalıdır.

6. Adım:

Filtreyi 5 dakika boyunca temizlemek için soğuk su vanasını açın. Herhangi bir

sızıntı olup olmadığını kontrol edin.

Opción 1

Opción 2

Paso 1:

Cierre la válvula de agua fría y abra el grifo para

Paso 2:

Retire la manguera de agua fría de la válvula de agua

Tamaño de la válvula de agua fría y accesorios

- Si la salida de la válvula angular es de 3/8", puede

conectarse directamente al suministro de agua.

Salida de 3/8

Opzione 1

Fase 1:

Chiudere la valvola dell'acqua fredda e aprire il rubinetto

Fase 2:

Rimuovere il tubo dell'acqua fredda dalla valvola

Dimensioni della valvola acqua fredda e raccordi necessari

- Se l'uscita della valvola ad angolo è da 3/8", può

essere collegata direttamente alla rete idrica.

Presa 3/8

- Se l'uscita della valvola ad angolo è da 1/2", può essere collegata tramite i seguenti due raccordi.

Questo filtro non deve essere utilizzato con acqua microbiologicamente non sicura

o di qualità sconosciuta senza un'adeguata disinfezione prima o dopo il sistema.

Fase 6:

Aprire la valvola dell'acqua fredda per lavare il filtro per 5 minuti Verificare

eventuali perdite.