Hoover DYN 166P8BC-80 Manuale utente

Categoria
Lavatrici
Tipo
Manuale utente

Questo manuale è adatto anche per

Instruction
Book
Instructions for installation and use
10kg Washing Machine
Washing Machine
Contents
Introduction 3
Delivery Information 3
Guarantee 3
Customer Service 4
Caring for the Environment 5
Warning and Safety Instructions 6
Unpacking the Product 7
Installation 8
Electricity Supply 8
Water Supply 9
Connecting the Cold Water Supply 10
Connecting the Drainage Pipe 11
Levelling the Machine 12
Testing the Installation 12
Description of the Machine 14
The Control Panel 15
Digital Display 16
Wash Options 18
Automatic Features 21
Programme Descriptions 22
Programme Guide 24
Detergent 26
Laundry 27
Washing Advice 28
Running a Wash Cycle 29
Care and Maintenance 31
Problem Solving Guide 33
After Sales Service 37
2
This appliances is intended to be used in household and similar applications such as:
- staff kitchen areas in shops, offices and other working environments;
- farm houses;
- by clients in hotels, motels and other residential type environments;
- bed and breakfast type environments.
A different use of this appliance from household environment or from typical housekeeping
functions, as commercial use by expert or trained users, is excluded even in the above
applications.
If the appliance is used in a manner inconsistent with this it may reduce the life of the
appliance and may void the manufacturer’s warranty.
Any damage to the appliance or other damage or loss arising through use that is not
consistent with domestic or household use (even if located in a domestic or household environment)
shall not be accepted by the manufacturer to the fullest extent permitted by law.
Introduction
Please read and follow these instructions carefully and operate the machine
accordingly. This booklet provides important guidelines for safe use, installation,
maintenance and some useful advice for best results when using your machine.
Please complete the information below referencing your products details found on the
rating plate that is attached to the porthole of your machine:
Model Number:___________________
Serial Number (16 digits): _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Our customer service advisors will require this information whenever you contact
Hoover. Please keep all documentation in a safe place for future reference or for any
future owners.
Delivery information
Please check that the following items are delivered with the appliance:
Instruction manual
Guarantee card
Blanking plugs
Inlet hose
Check that no damage has occurred to the machine during transit.
Guarantee
Your new Hoover appliance comes with a 12-month call-out, parts and labour
guarantee. Registering your appliance also gives you an additional 4-year parts
guarantee absolutely free. To activate both your 12-month and 4 year guarantees, you
must register your appliance within 30 days, quoting your model number, serial
number, plus the date and price of you purchase.
Register your appliance now by calling
08444 810 157
or register online
www.hoover.co.uk
If you would like to register for an additional 4 years labour protection, please ask our
service advisor for cost details, or complete the enclosed form.
3
4
Customer Service
At Hoover, we aim to make appliances that are reliable and long lasting. However,
should your appliance need to be serviced during its working life, no one is more
qualified to maintain your appliance than our own Hoover Service engineers. To book
a service call or to ask our customer service advisors for help on using your appliance,
please call:
08444 995599
Alternatively, you can consult our Problem Solving Guide on page 33.
Technical data
Max. load of dry laundry for washing
Water pressure
Measurements
Height
Width
Depth
NB: For specifications regarding electrical data, see the data panel on the front of the
washing machine (porthole area).
11 kg
0.05 ÷ 0.8 MPa
85 cm
60 cm
64 cm
Caring for the environment
Together, we share the responsibility to safeguard our environment for future
generations.
At Hoover, that means continually developing new, intelligent technologies to produce
electrical appliances that perform more efficiently and use less electricity and less
water. This significantly reduces the carbon footprint from your appliance.
Our ongoing commitment will ensure that we will continue to develop more intelligent,
more efficient appliances for future generations.
European Directive
2002/96/EC
This appliance is marked according to the European directive
2002/96/EC on Waste Electrical and Electronic Equipment
(WEEE).
By ensuring this product is disposed of correctly, you will help
prevent potential negative consequences for the environment and
human health, which could otherwise be caused by inappropriate
waste handling of this product.
The symbol on the product indicates that this product may not be
treated as household waste. Instead it shall be handed over to the
applicable collection point for the recycling of electrical and
electronic equipment.
Disposal must be carried out in accordance with local
environmental regulations for waste disposal.
For more detailed information about treatment, recovery and
recycling of this product, please contact your local city office, your
household waste disposal service or the shop where you purchased
the product.
5
Warning and Safety
Instructions
This machine is solely for domestic use, i.e. to wash, rinse and spin dry household
textiles and garments.
Do not touch the appliance when hands or feet are damp or wet.
Do not lean on the door when loading the machine or use the door to lift or move the
machine.
Do not try to open the door when water is visible in the drum or the door locked
indicator is ON.
Do not touch the drained water as it may reach extremely high temperatures.
Do not use adapters, multiple connectors and / or extensions leads.
Do not pull the power cord or the appliance itself to remove the plug from the socket.
Ensure the appliance mains supply is earthed, and if it is not, seek assistance from a
qualified person.
If the power cable is damaged, it must only ever be replaced by an authorised
serviceman.
Never force the porthole door: doing so may damage the safety lock mechanism
designed to prevent the door being opened accidentally.
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
When moving the appliance, never lift it by the controls, detergent drawer or door,
and never attempt to move it alone as the machine is extremely heavy.
When in transit, never rest the door against the trolley or transport the appliance
without its polystyrene base.
If the appliance is installed on a carpeted floor ensure that the ventilation holes on the
base of the appliance are not obstructed.
If the appliance is not running properly or breaks down, switch off the power, turn off
the tap and do not tamper with the appliance.
Contact an authorised serviceman and ask them to use official Hoover spare parts.
Warning! The company denies all liability if and when these instructions are not
respected.
6
Unpacking the Product
Remove the machine from its packaging close to the final location of the machine.
Step 1. Remove all outer packaging from the
machine. Check there is no damage to the machine
before continuing the installation process.
Step 2. Carefully cut through the hose-retaining clip
at the rear of the machine, taking care not to cut
the hose itself.
Step 3. Remove the 4 retaining screws at the rear
of the machine, as indicated in the image on the
left. Use the blanking plugs provided in the
instruction booklet pack to cover the holes once the
screws have been removed.
Step 4. Tilt the machine forward and apply the
insulation base panel (corrugated plastic) to the
base of the machine using the self-adhesive strips.
All packaging materials used are environmentally friendly and recyclable. Please help
dispose of the packaging via environmentally friendly means. Your local council will be
able to give you details of current means of disposal.
7
Installation
Before installing the machine, ensure that the mains plug and water supply valves are
easily accessible from your chosen machine location.
Make sure there is enough space for the machine. Select a space at least 600mm wide
and 850mm high. Also leave enough space to open the door fully so you can load
and unload it easily.
Keep the area underneath and around the machine free of combustible materials such
as lint, paper, rags, chemicals etc.
All machines are tested with water prior to leaving the factory, so a small amount of
water may be present in the drum and the drain hose.
Flooding may occur if any part of the installation process is not completed correctly.
Electricity Supply
Washing machines are supplied to operate at a voltage of 230-240V, 50 Hz single
phase. Please check that the supply circuit is rated to at least 13A.
The plug is already equipped with a 13A fuse, which is BS 1362 ASTA approved. Any
replacement must be the same rating and specification. If the fuse cover is lost, do not
use the plug until it is replaced.
Electricity can be extremely dangerous. Please take care when connecting your
machine to the electricity supply.
This washing machine must be earthed.
The socket outlet and the plug on the appliance must be of the same type.
Do not use multiple adapters and/or extension leads.
The wires in the mains lead are coloured in accordance with the following codes:
Blue NEUTRAL
Brown LIVE
Green and Yellow EARTH
Appliance complies with European Directive 73/23/EEC, 89/336/EEC
replaced by 2006/95/EC and 2004/108/EC and subsequent amendments.
8
Water Supply
This machine should only be connected to a cold-water supply. The cold-water
pressure should be between 0.5 and 8 bar (0.05-0.8 Mpa).
Do not connect the machine to a single outlet instantaneous water heater.
Before connecting the fill hose, check that the water is running from the water supply
tap to be used. Let the water flow from the tap until the water runs clear before
connecting to the machine. The water supply tap should be accessible when the
machine is installed.
The water-stop device protects against water damages
caused by leaks on the fill hose which could develop
due to natural ageing of the hose.
In the water-stop system the leaking water fills the
corrugated hose and activates a stop valve which cuts
off the water supply to the machine.
This fault is shown by a red sector on the window "A".
Would this occur, please refer to your Service Agent.
9
Safety antitwist device
(press and twist to remove
the washer)
A
Connecting the Cold Water
Supply
Only one hose is required to install this machine to a cold water supply. Cold fill is an
energy efficient system. Only the water required to wash the laundry is heated. There
is no loss of heat in the pipeline from the hot water tank or the boiler.
If your previous machine installation was hot and cold fill ensure that the hot tap is
firmly closed to prevent leakage.
This machine has an inlet hose with a 19mm (3/4") threaded ferrule fitted to the end,
to attach between the threaded connector on the appliance and the water supply. Only
use the new hose supplied to connect the machine and ensure that the sealing washers
are in place inside the hose connectors.
Do not re-use old hoses that are attached to existing installations.
Do not over-tighten the connections. Hand tight is sufficient.
Do not trap or kink the hose.
Step 1. Connect the elbow end of the hose
provided to the threaded inlet on the back of the
machine.
The grey pipe needs to connect to the white
threaded inlet on the machine.
Step 2. Hand tighten the connector.
Step 3. Connect the straight ends of the pipes to
the water supply; ensure that there are no kinks.
Step 4. Turn on the water supply and check there
are no leaks. If there is a leak, turn off the water
supply, disconnect the hose and check the sealing
washers are in place. Refit the hose and turn on
the water supply.
10
Connecting the drainage pipe
This machine must be connected in accordance with the water supply regulations.
Water bylaws prohibit connection to a surface water drain.
Decide which plumbing option suits you best then follow the instructions below:
Option 1 - Waste pipe connection (waste trap)
Fit the hooked end support to the outlet pipe and position it at least 800mm off the
floor.
After removing the blanking plug, or cutting the membrane from the waste system,
securely fix the outlet pipe to the drainage system, using a hose clip.
Secure the hooked end support up to at least 800mm to avoid water being drawn
back into the machine.
Option 2 - Into a standpipe
Ensure that the standpipe is not located near an electrical socket.
Fit the hooked end support to the outlet pipe. Install the hose into the standpipe
ensuring that the pipe is at least 500mm from the floor.
Insert the outlet pipe approximately 100mm into the standpipe.
11
Levelling The Machine
Your machine is heavy so care must be taken when moving it.
We recommend that two people move the machine to avoid strain and possible injury.
Take care not to damage flooring when moving the machine and do not drag or lift
the machine by its door.
When moving the machine to its final position, take care not to kink or damage the
hose at the back of the machine.
Once the machine is in place the feet should be adjusted to ensure that the machine is
level. If the machine is not level it may become very noisy or move during the spin
cycle.
Step 1. Turn the locking nut clockwise to release the screw adjuster on the feet.
Step 2. Adjust the feet on the corners of the machine by rotating each foot to raise or
lower its position until it is firm and level on the ground.
Step 3. When the machine is firm and level, tighten the locking nuts on the feet in an
anti-clockwise direction until they reach the base of the machine.
Testing the Installation
Refer to “Selecting the wash programme” for details of how to select programmes.
Step 1. Turn on the water supply and check for leaks from the fill hose.
Step 2. Switch on the electricity supply.
Step 3. Switch on the appliance by the ON/OFF button. Select the spin programme
and then press the Start Pause button to start the machine. Allow the programme to
continue for one minute and then cancel the programme by pressing and holding the
START/PAUSE button for about 5 second. This will remove any water remaining in the
machine from factory testing.
Step 4. To check for cold water filling to the machine:
Select the rinse programme and press the Start Pause button to start the machine.
Once the rinse has finished, allow the tumble action to continue until the water has
pumped out. Check that the drain outlet is not leaking or overflowing.
12
Step 5. Select the spin programme and press the Start Pause button to start the
machine. If the machine takes longer than one minute to empty check the drain hose
for kinks.
Installation testing is now complete.
Now you have successfully installed the machine we advise that you run the machine
to ensure the drum is thoroughly clean after testing and storage. Select Cottons 90°C
programme and run the machine for a complete cycle using only wash detergent and
water.
This programme will take approximately 2 hours to complete.
13
Description of the Machine
The Hoover washing machine details are indicated below:
Detergent
Dispenser
Control
Panel
Door
Handle
Porthole
Door
Filter
Adjustable
Feet
14
The Control Panel
Turning the Machine On
Pressing the ON/OFF ( ) button will turn the machine on.
Start Pause Button
START
After selecting the programme and the required options press the Start Pause button
once to start the wash cycle. There will be a short time delay to the start of the
programme while the machine sets the wash parameters for the selected programme
and options. The Door Locked and KG Mode indicator lights will also illuminate a few
seconds after pressing the Start Pause button.
In some programs in the initial phase of the cycle there are planned spin sequences to
ensure optimal wash results.
PAUSE
The programme may be paused at any time during the wash cycle by holding down
the Start Pause button for about two seconds. The door locked indicator light will
remain illuminated for approximately 2 minutes. The door can be opened when this
indicator goes out. To restart the programme, press the Start Pause button once again.
Cancelling and Changing the Programme
To cancel the programme hold down the START/PAUSE button for about five seconds.
Select a new programme and start as detailed above.
Temperature
Button
15
LCD
Display
Delay Start
Button
Start/Pause
Button
On/Off
Button
Night
& Day
Stain
Blaster
Sensitive
Care
Pre
Wash
Rinse
Hold
Easy Iron
Wash Time
Button
Programme
Buttons
Spin Speed
Button
20
°
40°C
60°C
Cottons
Door Locked indicator
The Door Locked indicator light is illuminated when the door is fully closed and the machine
is ON.
When Start Pause is pressed on the machine with the door closed the indicator will flash
momentarily and then illuminate. If the door is not closed the indicator will continue to flash.
A special safety device prevents the door from being opened immediately after the end of
the cycle. Wait for 2 minutes after the wash cycle has finished and the door locked light has
gone out before opening the door. As a safety measure, check that there is no water evident
in the drum. At the end of the cycle press the ON/OFF ( ) button.
If the programme is paused, the door locked indicator will go out after 2 minutes and the
door can be opened. Check there is no water evident in the drum before opening the door.
Digital Display
The easy-to-use Digital Display gives you total control of your wash cycle, whether it is
adjusting the wash length using our Wash Time Selector, delaying the start of your
wash, or adjusting the temperature and spin speed of your selected programme. The
simplicity of the Digital Display understates the advanced technology, which clearly
displays all the wash cycle information, putting you in control.
Wash Temperature
When a programme is selected the relevant indicator will light up to show the
recommended wash temperature. You can select a different temperature by pressing
the Temperature button. For example: The Cottons programme will default to 40°C.
With this control the temperature can be reduced to 30°C to reduce energy
consumption or increased to 60°C for a more intensive wash.
Today, most detergents have been improved to wash efficiently at lower temperatures,
therefore we have set the default temperature settings of each programme to a lower
level, saving electricity and reducing the carbon footprint of your machine.
Please refer to the Programme Guide for the maximum temperature to which each
programme can be set.
Wash Cycle Time/
Delay Start Indicator
Kg Mode
Indicator
Wash Temperature
Indicator
Spin Speed
Indicator
Wash Length
Indicator
16
Buttons
Indicator
Door locked
Indicator
Maximum loading capacity and
detergent Indicator
Spin Speed
When a programme is selected the maximum spin speed allowed for that programme
appears on the display. Pressing the Spin Speed button will reduce the speed by
100rpm each time the button is pressed. The minimum speed is 400rpm, or continuing
to press the button will eliminate the final spin completely.
Delay Start
This indicator shows the number of hours time delay, once the delay start has been set.
Wash Cycle Time
When a programme is selected the display automatically shows the maximum cycle
duration for a full load, which can vary, depending on the options selected. Once the
programme has started you will be kept informed constantly of the time remaining to
the end of the wash.
Wash Length Indicator
Once the programme has been selected the indicator light will automatically show
the wash time set for that programme. Selecting a different wash time the relevant
indicator will light up.
KG Mode Indicator
Available on Cotton and Synthetic cycles, during the first 4 minutes of the cycle the
indicator lights and wash time will flash. This means the intelligent sensor is weighing
the laundry and will adjust the cycle time, water and electricity consumption
accordingly.
Buttons Indicator Light
These light up when the relevant buttons are pressed.
If an option is selected but it is not compatible with the selected programme then the
symbol first flashes and then goes off.
Maximum Loading Capacity And Detergent Indicator
When a programme is selected on the display is shown the maximum load of laundry
suitable for that cycle and the relative detergent quantity.
Detergent:
20% of the maximum quantity
50% of the maximum quantity
maximum quantity
The detergent quantity suggested can be vary depending on how much the fabrics are soiled.
Maximum load
Every levels shown on the display is the 10% of the maximum loading capacity.
When a programme is selected the maximum capacity suggested is shown on the
display. For the programmes where the KG MODE function is active, the appliance in
the first minutes it calculates the real laundry loaded, updating the levels on the display
in real time.
17
Wash Options
The following options should be chosen once the required programme has been
selected and BEFORE pressing the Start Pause button. The indicator light on each
option button will illuminate if that option has been selected.
Night & Day
Press this button (available for all the washing programmes) to reduce the
intermediate spin speed to 400 rpm, where applicable; the water level is increased
during rinsing and the washing is kept immersed in water after the final rinse in order
to spread the fibres evenly.
During the phase in which the water is held in the tub, the indicator lights to show that
the machine is at a standstill.
Release the button to end the cycle with a spin dry (which may be reduced or
cancelled using the appropriate button) and emptying phase.
Thanks to electronic control, the water in the intermediate phases is emptied silently,
making this option very useful for washing at night.
Pre-Wash
This option is particularly useful for heavily soiled loads and can be used only on some
programmes as shown in the programmes table.
Detergent for this programme should be added to the compartment of the soap drawer
labelled “I” (Please refer to Detergent Drawer Section of manual). We recommend you
use only 20% of the recommended quantities shown on the detergent pack and fabric
conditioner should not be used for this programme.
Stain Blaster
The Stain Blaster option, selectable on all Cotton cycles, tackles stubborn stains by
maintaining wash temperatures throughout the programme and adjusting the spin
speed of the drum during critical stages of the wash and rinse cycles. Using this
special programme will increase the wash efficiency without increasing the length of
your wash programme.
Rinse Hold
Pressing this button means the cycle stops at the final rinse stage, leaving the drum fil-
led with water.
The garments thus stay immersed in the water, preventing them from bunching up and
forming creases that are difficult to remove.
During the phase in which the water is held in the tub, the indicator blinks to show that
the machine is at a standstill. Release the button to end the cycle with a spin (which
may be reduced or cancelled using the appropriate button) and emptying phase.
18
Sensitive Care
The Sensitive Care option washes your clothes in a deeper than normal water level to
provide gentler washing for especially delicate fabrics, while detergent is removed
thoroughly with five extra rinses. Perfect for people with delicate skin, this option can
be selected on all Cotton and Synthetic cycles.
This option does not need to be selected on the Delicate, Woollen or Silk programmes,
as it is already an integrated part of the wash cycles.
Easy Iron
This function, selectable on Mixed and Delicate cycles, minimizes creases as much as
possible with a uniquely designed anti-crease system that is tailored to specific fabrics.
The water is gradually cooled throughout the final two rinses with no spinning and
then a delicate spin assures the maximum relaxation of the fabrics.
Delay Start
This option allows you to delay the start of your wash cycle by up to 24 hours. By
pressing the Delay Start button, the time delay will be shown on the display (h00). This
will increase in one-hour intervals each time the Delay Start button is pressed.
Continue to press the button until the required time is reached, then press the Start
Pause button to activate the machine. The machine will start its cycle once the required
number of hours has passed.
To cancel the Delay Start option, press and hold the button for 5 seconds until the
display shows the settings for the selected programme. To start this programme, press
the Start Pause button. To cancel the process, press the ON/OFF button or select
another programme.
Temperature
When a programme is selected the display will show the recommended wash tempera-
ture. The Temperature button can be used to decrease or increase the temperature of
your chosen wash cycle. Each time the button is pressed, the new temperature level is
shown on the Wash Temperature Indicator.
19
Sensitive Care
The Sensitive Care option washes your clothes in a deeper than normal water level to
provide gentler washing for especially delicate fabrics, while detergent is removed
thoroughly with a much larger quantity of water. Perfect for people with delicate skin,
this option can be selected on all Cotton and Synthetic cycles.
This option does not need to be selected on the Delicate, Woollen or Silk programmes,
as it is already an integrated part of the wash cycles.
Spin Speed
The spin cycle is used to remove as much water as possible from the laundry without
damaging your clothes. The recommended spin speed for each programme is already
set to the highest level for that chosen programme. By pressing the Spin Speed button
you can reduce the spin speed in 100rpm intervals.
To cancel the spin cycle altogether, set the spin speed to 0.
It is not possible to select a spin speed higher than that suitable for the programme
selected. This feature is designed to avoid damage to your clothes.
It is possible to modify the spin speed at any time without stopping or pausing the
machine.
Wash Time Selector
Once the programme has been selected the indicator light will automatically show the
wash time set for that programme. Selecting a different wash time the relevant indica-
tor will light up. For example: Using this button on the Rapid Wash cycle will enable
you to select either a 14, 30 or 44 minute wash cycle.
This selection is only available on the Cotton, Synthetic and Rapid programmes.
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

Hoover DYN 166P8BC-80 Manuale utente

Categoria
Lavatrici
Tipo
Manuale utente
Questo manuale è adatto anche per