Samsung SH09AP4E Manuale utente

Categoria
Condizionatori d'aria a sistema split
Tipo
Manuale utente

Questo manuale è adatto anche per

E§§HNIKA
ENGLISH
OWNERS INSTRUCTIONS
MANUAL DE INSTRUCCIONES
MANUEL DUTILISATION
ISTRUZIONI PER LUSO
MANUAL DE INSTRUÇÕES
GEBRAUCHSANWEISUNG
√¢∏°π∂™ Ã∏™∆∏
Split-type Room Air Conditioner (Cool and Heat)
Aire acondicionado doméstico sistema Split (Refrigeración y Calefacción)
Climatiseur de type Séparé
(Refroidissement et Chauffage)
Condizionatore daria per ambienti ad unità Separate (Raffreddamento e Riscaldamento)
Aparelho de ar condicionado tipo Split (Refrigeração e Aquecimento)
Geteilte raumklimaanlage
(Kühlen und Wärmen)
¢IAIPOYMENO K§IMATI™TIKO ¢øMATIOY (æ‡Í˘ Î·È £¤ÚÌ·ÓÛ˘)
ESPAÑOL
FRANÇAIS
ITALIANO
PORTUGUÊS
DEUTSCH
E S F I P D G DB98-24443A(1)
Indoor unit Outdoor unit
AQ07P2GBE
AQ07P2GEE
SH07AP4E
SH07ZP2E
AQ09P2GBE
AQ09P2GEE
SH09AP4E
SH09ZP2E
AQ12P4GBE
AQ12P4GEE
SH12AP4E
SH12ZP4E
AQ18PJGBE
AQ18PJGEE
SH18APJE
SH18ZPJE
AQ24P6GBE
AQ24P6GEE
SH24AP6E
SH24ZP6E
UQ07P2GBE
UQ07P2GEE
SH07AP4EX
SH07ZP2EX
UQ09P2GBE
UQ09P2GEE
SH09AP4EX
SH09ZP2EX
UQ12P4GBE
UQ12P4GEE
SH12AP4EX
SH12ZP4EX
UQ18PJGBE
UQ18PJGEE
SH18APJEX
SH18ZPJEX
UQ24P6GBE
UQ24P6GEE
SH24AP6EX
SH24ZP6EX
E-2
Safety Precautions
The following safety precautions must be taken when using your air conditioner.
Users of this product are cautioned not to attempt repair of this product
at their own discretion. Instead, they are requested to directly contact a
designated service center or the outlet at which the product was
purchased.
Never spill any kind of liquid into the unit. Should this happen, unplug
or main switch off the unit and contact an authorized service center.
Do not insert anything between the air outlet blades because the inner
fan may be damaged and could cause injury. Keep children away from
the unit.
Do not place any obstacles in front of the unit.
Do not spray liquid of any kind into the indoor unit. Should this happen,
switch off the breaker used for your air conditioner and contact your
installation specialist.
Make sure that the unit is correctly ventilated at all times:
Do not place clothing or other materials over it.
If the wireless remote control will not be used for a long time, remove
the batteries. (If applicable)
When using a wireless remote control, the distance should not be more
than 7 meters from the air conditioner. (If applicable)
WARNING
DURING OPERATION
Never store or ship the air conditioner upside down or sideways to
avoid damage to the compressor.
The appliance is not intended for use by young children or infirm
persons without supervision: Young children should be supervised to
ensure that they do not play with the appliance.
Max current is measured according to IEC standard for safety and
current is measured according to ISO standard for energy efficiency.
OTHERS
Before throwing out the device, it is necessary to pull back the battery
cells and get rid of them safely for recycling reasons.
When you need to dispose of the unit, consult your dealer. If pipes are
removed incorrectly, refrigerant may blow out and come into contact
with your skin, causing injury. Releasing refrigerant into the atmosphere
also damages the environments.
Please recycle or dispose of the packaging material for this product in
an environmentally responsible manner.
D
ISPOSING OF THE UNIT
Risk of electric shock. Can cause injury or death. Disconnect all
remote electric power supplies before servicing, installing or cleaning.
This must be done by the manufacturer or its service agent or a similar
qualified person in order to avoid a hazard.
Register your product at www.samsung.com/global/register
E-3
ENGLISH
Contents
P
REPARING YOUR AIR CONDITIONER
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
View of the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Remote Control-Buttons and Display . . . . . . . . . . . . . . . . . . . . . . 6
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Inserting the Remote Control Batteries . . . . . . . . . . . . . . . . . . . . . 8
O
PERATING YOUR AIR CONDITIONER
Selecting the Automatic Operating Mode . . . . . . . . . . . . . . . . . . . 9
Cooling Your Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Heating Your Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Changing the Room Temperature Quickly . . . . . . . . . . . . . . . . . . 12
Removing Excess Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Airing Your Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Selecting Energy Saving Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Generating Anions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Adjusting the Air Flow Direction Vertically . . . . . . . . . . . . . . . . . . . 17
Adjusting the Air Flow Direction Horizontally . . . . . . . . . . . . . . . . 17
P
ROGRAMMING YOUR AIR CONDITIONER
Setting the On Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Setting the Off Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Setting the Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
R
ECOMMENDATIONS FOR USE
Operating Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Temperature and Humidity Ranges . . . . . . . . . . . . . . . . . . . . . . . . 22
Operating Your Air Conditioner Without the Remote Control . . . . . 22
Solving Common Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Cleaning Your Air Conditioner . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Cleaning Deodorizing and Bio Filters (Option) . . . . . . . . . . . . . . . 25
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed with other household
wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable
reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government
office, for details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
View of the Unit
E-4
If you want to turn on/off the Display during operation,
press the button on the remote control.
The room temperature sensor senses air temperature around
the sensor, and shows the temperature on the display.
NN
NN
oo
oo
tt
tt
ee
ee
Indoor Unit
Air filter
(under the grille)
Air flow blades
(outlet)
Remote Control Sensor
On/Off switch
Timer indicator
Fan speed setting
Sleep Timer indicator
Operation indicator
Set temperature &
room temperature
Anions indicator
Auto grille
Air Inlet
Room temperature sensor
The design and shape are subject to change according to the model.
E-5
ENGLISH
Air Inlet(Rear)
Air Outlet
Connection Valve
Outdoor Unit
UQ18PJGBE UQ18PJGEE SH18ZPJEX
Air Inlet(Rear)
Air Outlet
Connection Valve
Outdoor Unit
UQ07P2GBE UQ07P2GEE SH07AP4EX SH07ZP2EX
UQ09P2GBE UQ09P2GEE SH09AP4EX SH09ZP2EX
UQ12P4GBE UQ12P4GEE SH12AP4EX SH12ZP4EX
Air Inlet (Rear)
Air Outlet
Connection Valve
Outdoor Unit
SH18APJEX
Air Inlet (Rear)
Air Outlet
Connection Valve
Outdoor Unit
UQ24P6GBE UQ24P6GEE SH24AP6EX SH24ZP6EX
Remote Control - Buttons and Display
E-6
Operating mode
( AUTO, COOL, DRY,
FAN, HEAT)
Remote control
transmission indicator
Off Timer setting
Energy saving
Anions button
Sleep button
Energy saving button
Swing button
Timer Set/Cancel button
Temperature adjustment
buttons
Temperature setting
Air flow direction
Turbo mode
Sleep mode
On/Off button
Mode selection button
(AUTO, COOL, DRY, FAN, HEAT)
Fan speed adjustment
button
Turbo button
On Timer button
Off Timer button
Fan speed
Anions indicator
On Timer setting
Battery discharge indicator
Digital On/Off button
G
etting Started
You have just purchased a split type air conditioner and it has been
installed by your installation specialist.
Your Owner’s Instructions contains valuable information on using your
air conditioner. Please take the time to read it as it will help you take full
advantage of the unit’s features.
The booklet is organized as follows.
The following figures are shown on pages from 4 to 6 :
- Indoor and outdoor units
- Remote control(buttons and display)
They will help you find the buttons and understand the symbols displayed.
In the manual, you will find a series of step-by-step procedures for each
function available.
The illustrations in the step-by-step procedures use three different symbols:
PRESS PUSH HOLD DOWN
E-7
ENGLISH
Inserting the Remote Control Batteries
Push the battery cover on the rear of the remote control with your thumb
in the direction of the arrow and remove it.
Insert the two batteries, taking care to respect the polarities :
+ on the battery with + on the remote control.
- on the battery with - on the remote control.
1
2
Close the cover by sliding it back until it clicks into place.
3
Use two AAA, LR03 1.5V batteries.
Do not use old batteries or different kinds of batteries together.
Batteries may be completely discharged after 12 months, even
if they have not actually been used.
You must insert or replace the remote control batteries when :
You purchase the air conditioner
The remote control does not work correctly
NN
NN
oo
oo
tt
tt
ee
ee
E-8
Selecting the Automatic Operating Mode
E-9
ENGLISH
You can start the air conditioner in Automatic mode from your remote
control. In the Automatic mode, the optimum temperature and the fan
speed is selected automatically.
1
If the is not displayed at the top of the remote control,
press the button on the remote control one or more times until it
appears.
Result
: The indoor unit beeps each time you press the button.
The air conditioner runs in AUTO mode.
2
You can change modes at any time.
If necessary, press the (On/Off) button.
Result: The operation indicator on the indoor unit lights up.
The air conditioner starts up in the mode selected
when the unit was last used.
The indoor unit beeps.
The air conditioner is fitted with a protection mechanism to
prevent the unit from being damaged when it is started
immediately after being:
Plugged in
Stopped
lt will start up normally after three minutes.
IMPORTANT
NN
NN
oo
oo
tt
tt
ee
ee
Cooling Your Room
1
If necessary, press the (On/Off) button.
Result:
The operation indicator on the indoor unit lights up.
The air conditioner starts up in the mode selected
when the unit was last used.
The indoor unit beeps.
The air conditioner is fitted with a protection mechanism to
prevent the unit from being damaged when it is started
immediately after being:
Plugged in
Stopped
lt will start up normally after three minutes.
IMPORTANT
If the is not displayed at the top of the remote control,
press the button on the remote control one or more times until it
appears.
Result:
The indoor unit beeps each time you press the button.
The air conditioner runs in COOL mode.
2
You can change modes at any time.
NN
NN
oo
oo
tt
tt
ee
ee
To adjust the temperature, press the button one or more times until
the required temperature is displayed.
Possible temperatures are between 18°C and 30°C inclusive.
Result:
Each time you press the button:
- The temperature is adjusted by 1°C
- The indoor unit beeps
The air conditioner starts cooling, provided that the room
temperature is higher than the selected temperature.
If the room temperature reaches the set temperature, the air
conditioner stops cooling, but the fan is still operating.
3
Select the fan speed by pressing the button one or more times
until the required setting is displayed:
Automatic (rotated : )
Low
Medium
High
Result
: Each time you press the button, the indoor unit
beeps.
4
To control the direction of the air flow, refer to page 17.
5
You must select the Cool mode if you wish to adjust the:
Cooling temperature
Fan speed when cooling
E-10
Heating Your Room
E-11
ENGLISH
You must select the Heat mode if you wish to adjust the:
Heating temperature
Fan speed when heating
1 If necessary, press the (On/Off) button.
Result
:
The operation indicator on the indoor unit lights up.
The air conditioner starts up in the mode selected when
the unit was last used.
The indoor unit beeps.
The air conditioner is fitted with a protection mechanism
to prevent the unit from being damaged when it is started
immediately after being:
Plugged in
Stopped
It will start up normally after three minutes.
2 If the is not displayed at the top of the remote control, press the
button on the remote control one or more times until it appears.
Result
:
The indoor unit beeps each time you press the button.
The air conditioner runs in HEAT mode.
NN
NN
oo
oo
tt
tt
ee
ee You can change modes at any time.
3 To adjust the temperature, press the button one or more times
until the required temperature is displayed.
Possible temperatures are between 16°C and 30°C inclusive.
Result
: Each time you press the button:
- The temperature is adjusted by 1°C
- The indoor unit beeps
The air conditioner starts heating, provided that the room
temperature is lower than the desired temperature
(selected temperature+3°C).
If the room temperature reaches the set temperature, the air
conditioner stops heating, but the fan is still operating.
4 Select the fan speed by pressing the button one or more times
until the required setting is displayed:
Automatic (rotated : )
Low
Medium
High
Result
:
Each time you press the button, the indoor unit beeps.
For the first three to five minutes, the fan operates very
slowly until the air has been sufficiently warmed. Once the
correct temperature has been reached, the fan is automatically
set to the required speed.
5 To control the direction of the air flow, refer to page 17.
IMPORTANT
Changing the Room Temperature Quickly
The Turbo cooling/heating function is used to cool or heat your room as
quickly as possible.
EE
EE
xx
xx
aa
aa
mm
mm
pp
pp
ll
ll
ee
ee
: You have just come home and find that the room is very
hot. You wish to cool it down as quickly as possible.
The Turbo function operates for 30 minutes with the maximum settings before
returning automatically to the mode and temperature previously selected.
1
If necessary, press the (On/Off) button.
Result
: The operation indicator on the indoor unit lights up.
The air conditioner starts up in the mode selected when the unit
was last used.
The indoor unit beeps.
2
Press the button.
Result
: The temperature and fan settings are adjusted automatically.
The air conditioner cools or heats the room as quickly as possible.
After 30 minutes, the air conditioner is reset automatically to the
previous mode, temperature and fan settings.
But, if you press the button in DRY or FAN mode,
it will change to AUTO mode automatically.
3
If you wish to stop the Turbo function before the end of the 30-minute period,
press the button again.
Result
: The air conditioner is reset automatically to the previous mode,
temperature and fan settings.
4
To control the direction of the air flow, refer to page
17.
E-12
Removing Excess Humidity
E-13
ENGLISH
If the atmosphere in your room is very humid or damp, you can
remove excess humidity without lowering the room temperature too
much.
1 If necessary, press the (On/Off) button.
Result
:
The operation indicator on the indoor unit lights up.
The air conditioner starts up in the mode selected when
the unit was last used.
The indoor unit beeps.
The air conditioner is fitted with a protection mechanism
to prevent the unit from being damaged when it is started
immediately after being:
Plugged in
Stopped
It will start up normally after three minutes.
2 If the is not displayed at the top of the remote control, press the
button on the remote control one or more times until it appears.
Result
:
The indoor unit beeps each time you press the button.
The air conditioner runs in DRY mode.
NN
NN
oo
oo
tt
tt
ee
ee You can change modes at any time.
3 To adjust the temperature, press the button one or more times
until the required temperature is displayed.
Possible temperatures are between 18°C and 30°C inclusive.
Result
: Each time you press the button:
- The temperature is adjusted by 1°C
- The indoor unit beeps
The air conditioner starts removing the excess humidity;
the quantity of air is adjusted automatically.
4 To control the direction of the air flow, refer to page 17.
IMPORTANT
Airing Your Room
If the atmosphere in your room is stale, you can air the room using
the Fan feature.
1 If necessary, press the (On/Off) button.
Result
:
The operation indicator on the indoor unit lights up.
The air conditioner starts up in the mode selected when
the unit was last used.
The indoor unit beeps.
2 If the is not displayed at the top of the remote control,
press the button on the remote control one or more times until it
appears.
Result
:
The indoor unit beeps each time you press the button.
The air conditioner runs in FAN mode.
The temperature is set automatically.
NN
NN
oo
oo
tt
tt
ee
ee You can change modes at any time.
3 Select the fan speed by pressing the button one or more times
until the required setting is displayed:
Low
Medium
High
Result
: Each time you press the button, the indoor unit beeps.
4 To control the direction of the air flow, refer to page 17.
E-14
Selecting Energy Saving Mode
If you wish to save energy when using your air conditioner, select the
Energy saving mode with the Energy saving button.
3 Press the button.
Result
:
The indoor unit beeps.
The air conditioner runs in the Energy saving mode.
The outer air flow blade moves up and down.
To stop the Energy saving mode, press the button again.
4 To adjust the temperature, press the button one or more times
until the required temperature is displayed. Possible temperatures are
between 26°C and 30°C inclusive.
NN
NN
oo
oo
tt
tt
ee
ee If you want to adjust temperature under 26°C, cancel the
Energy saving mode before adjusting the temperature.
6 To control the direction of the air flow, refer to page 17.
5 To select the fan speed, press the button one or more times
until the required setting is displayed.
E-15
ENGLISH
1
If necessary, press the (On/Off) button.
Result: The operation indicator on the indoor unit lights up.
The air conditioner starts up in the mode selected
when the unit was last used.
The indoor unit beeps.
The air conditioner is fitted with a protection mechanism to
prevent the unit from being damaged when it is started
immediately after being:
Plugged in
Stopped
lt will start up normally after three minutes.
IMPORTANT
2 Select COOL mode by pressing the button.
NN
NN
oo
oo
tt
tt
ee
ee You can select the Energy saving mode only in COOL mode.
Generating Anions
The air conditioner can generate anions with an ionizer in the indoor
unit. Since it is an additional function, you can select it any mode,
even when the air conditioner is turned off.
1 Press the button.
Result
:
The air conditioner generates anions.
The indoor unit beeps.
2 If you wish to stop the Anions function, press the button again.
Result
: The air conditioner is reset automatically to the previous mode,
temperature and fan settings.
3
To control the direction of the air flow, refer to page 17.
NN
NN
oo
oo
tt
tt
ee
ee If you press the button during off, the air conditioner
will turn on automatically and generate anions in the Fan
mode with Low fan speed.
E-16
Adjusting the Air Flow Direction Vertically
Adjusting the Air Flow Direction Horizontally
There are two sets of inner air flow blades. Just as the outer air flow
blade can be adjusted vertically, the inner blades can be adjusted
horizontally.
1 Adjust each set of inner blades to the required position, by pushing or
pulling them sideways.
E-17
ENGLISH
Depending on the position of the indoor unit on the wall of your room,
you can adjust the position of the outer air flow blade on the bottom
of the unit, thus increasing the efficiency of the air conditioner.
1 Press the button one or more times as required.
Result
: The outer blade is adjusted vertically.
RECOMMENDATION When... Adjust the blade to face...
Cooling Upwards.
Heating Downwards.
2 If you want the blade to move up and down automatically when the air
conditioner is operating, press the button.
Result
: The blade move up and down, around the base position set.
3
To stop the blade moving up and down, press the button again.
NN
NN
oo
oo
tt
tt
ee
ee If you switch the air conditioner... Then the blade is...
Off Closed completely.
On again Set to the initial position powered.
Setting the On Timer
If you press the button when the Off Timer is set,
the Off Timer is also cancelled.
NN
NN
oo
oo
tt
tt
ee
ee
The On Timer enables you to switch on the air conditioner automatically
after a given period of time. You can set the period of time from
30 minutes to 24 hours.
To set the operating time, press the button one or more times until
the required time is displayed. Possible time is between 0.5 hour and 24
hour inclusive.
1
Press the (Set/Cancel) button to complete the setting.
Result:
The remaining time is displayed.
Blinking of the timer indicator stops.
The selected mode and the temperature on the display
disappear after 10 seconds.
The air conditioner will switch on automatically when the
counter displayed on the remote control reaches the set time
and disappears the On timer setting.
2
Press the (Set/Cancel) button.
To Cancel the On Timer
E-18
To select an operating mode in advance, press the button until the
desired mode is displayed at the top of the remote control.
Result:
The air conditioner will run in the selected mode when it is
turned on.
3
Setting the Off Timer
The Off Timer enables you to switch off the air conditioner automatically
after a given period of time. You can set the period of time from
30 minutes to 24 hours.
To set the operating time, press the button one or more times until
the required time is displayed. Possible time is between 0.5 hour and 24
hour inclusive.
1
You can see or change the setting mode and/or the temperature
by pressing the button or the button after setting the
Off timer.
NN
NN
oo
oo
tt
tt
ee
ee
Press the (Set/Cancel) button to complete the setting.
Result:
The remaining time is displayed.
Blinking of the timer indicator stops.
The air conditioner will switch off automatically when the
counter displayed on the remote control reaches the set time
and disappears the Off timer setting.
2
If you would like to turn the air conditioner on after 2 hours
and to operate it for 2 hours:
1. Press the button until ‘2.0 Hr’ is displayed.
2. Press the (Set/Cancel) button.
3. Press the button until ‘4.0 Hr’ is displayed.
4. Press the (Set/Cancel) button.
EE
EE
xx
xx
aa
aa
mm
mm
pp
pp
ll
ll
ee
ee
If you press the button when the On Timer is set,
the On Timer is also cancelled.
NN
NN
oo
oo
tt
tt
ee
ee
Press the (Set/Cancel) button.
To Cancel the Off Timer
E-19
ENGLISH
Setting the Sleep Timer
The Sleep Timer can be used when you are cooling or heating your
room to switch the air conditioner off automatically after a period of
six hours.
NN
NN
oo
oo
tt
tt
ee
ee If you wish to switch the unit off at a specific time, refer to
page 19.
1 Make sure that you have selected either COOL or HEAT mode.
2 Press the button.
Result
: The indoor unit beeps.
The air conditioner will be controlled as indicated in the
illustrations below.
Cooling The desired temperature is
increased by 1°C every hour.
When it has been increased
by 2°C (after two hours), the
temperature is maintained for
four hours.
Heating The desired temperature is
decreased by 1°C every hour.
When it has been decreased
by 2°C (after two hours), the
temperature is maintained for
four hours.
To Cancel the Sleep Timer
If you no longer wish to use the Sleep Timer that you have set, you
can cancel it at any time.
Press the button.
Result
: The indoor unit beeps.
The is no longer displayed.
The air conditioner operates normally.
E-20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26

Samsung SH09AP4E Manuale utente

Categoria
Condizionatori d'aria a sistema split
Tipo
Manuale utente
Questo manuale è adatto anche per

in altre lingue