Brooks 0251 / 0254 Istruzioni per l'uso

Tipo
Istruzioni per l'uso
Installation and Operation Manual
X-SE-0250-Series-eng
Part Number: 541B129AAG
October, 2017
0250 Series
5
Gas and Liquid Mass Flow
Secondary Electronics
Model 0254
Table Top Four Channel
Secondary Electronics
Model 0251
Single Channel
Secondary Electronics
Installation and Operation Manual
X-SE-0250-Series-eng
Part Number: 541B129AAG
October, 2017
0250 Series
ESD (Electrostatic Discharge)
CAUTION: This instrument contains electronic components that are susceptible to damage by static electricity. Proper handling procedures must be observed
during the removal, installation or other handling of internal circuit boards or devices.
Handling Procedure:
1. Power to unit must be removed.
2. Personnel must be grounded, via a wrist strap or other safe, suitable means before any printed circuit card or other internal device is installed,
removed or adjusted.
3. Printed circuit cards must be transported in a conductive container. Boards must not be removed from protective enclosure until immediately before
installation. Removed boards must immediately be placed in protective container for transport, storage or return to factory.
Comments
This instrument is not unique in its content of ESD (electrostatic discharge) sensitive components. Most modern electronic designs contain components
that utilize metal oxide technology (NMOS, SMOS, etc.). Experience has proven that even small amounts of static electricity can damage or destroy these
devices. Damaged components, even though they appear to function properly, exhibit early failure.
Brooks Instrument designs, manufactures and tests its products to meet many national and international standards. These products must be properly
installed, operated and maintained to ensure they continue to operate within their normal specifications. The following instructions must be adhered to
and integrated into your safety program when installing, operating and maintaining Brooks Instrument products.
To ensure proper performance, use qualified personnel to install, operate, update, program and maintain the product.
Read all instructions prior to installing, operating and servicing the product. If this instruction manual is not the correct manual, please see back cover
for local sales office contact information. Save this instruction manual for future reference.
WARNING: Do not operate this instrument in excess of the specifications listed in the Instruction and Operation Manual. Failure to heed
this warning can result in serious personal injury and / or damage to the equipment.
If you do not understand any of the instructions, contact your Brooks Instrument representative for clarification.
Follow all warnings, cautions and instructions marked on and supplied with the product.
WARNING: Prior to installation ensure this instrument has the required approval ratings to meet local and national codes. Failure to heed this warning can
result in serious personal injury and / or damage to the equipment.
Install your equipment as specified in the installation instructions of the appropriate instruction manual and per applicable local and national codes.
Connect all products to the proper electrical and pressure sources.
Operation: (1) Slowly initiate flow into the system. Open process valves slowly to avoid flow surges. (2) Check for leaks around the flow meter inlet
and outlet connections. If no leaks are present, bring the system up to the operating pressure.
Please make sure that the process line pressure is removed prior to service. When replacement parts are required, ensure that qualified people use
replacement parts specified by Brooks Instrument. Unauthorized parts and procedures can affect the product's performance and place the safe
operation of your process at risk. Look-alike substitutions may result in fire, electrical hazards or improper operation.
Ensure that all equipment doors are closed and protective covers are in place to prevent electrical shock and personal injury, except when
maintenance is being performed by qualified persons.
WARNING: For liquid flow devices, if the inlet and outlet valves adjacent to the devices are to be closed for any reason, the devices must be completely
drained. Failure to do so may result in thermal expansion of the liquid that can rupture the device and may cause personal injury.
All pressure equipment with an internal pressure greater than 0.5 bar (g) and a size larger than 25mm or 1" (inch) falls under the Pressure Equipment Directive (PED).
The Specifications Section of this manual contains instructions related to the PED directive.
Products described in this manual are in compliance with EN directive 2014/34/EU.
All Brooks Instrument Flowmeters fall under fluid group 1.
Products larger than 25mm or 1" (inch) are in compliance with PED category I, II or III.
Products of 25mm or 1" (inch) or smaller are Sound Engineering Practice (SEP).
The Brooks Instrument (electric/electronic) equipment bearing the CE mark has been successfully tested to the regulations of the Electro Magnetic
Compatibility (EMC directive 2014/30/EU).
Special attention however is required when selecting the signal cable to be used with CE marked equipment.
Quality of the signal cable, cable glands and connectors:
Brooks Instrument supplies high quality cable(s) which meets the specifications for CE certification.
If you provide your own signal cable you should use a cable which is overall completely screened with a 100% shield.
“D” or “Circular” type connectors used should be shielded with a metal shield. If applicable, metal cable glands must be used providing cable screen clamping.
The cable screen should be connected to the metal shell or gland and shielded at both ends over 360 Degrees.
The shield should be terminated to an earth ground.
Card Edge Connectors are standard non-metallic. The cables used must be screened with 100% shield to comply with CE certification.
The shield should be terminated to an earth ground.
For pin configuration : Please refer to the enclosed Instruction Manual.
European Pressure Equipment Directive (PED)
European Electromagnetic Compatibility (EMC)
Essential Instructions
Read before proceeding!
Installation and Operation Manual
X-SE-0250-Series-eng
Part Number: 541B129AAG
October, 2017
0250 Series
Dear Customer,
We appreciate this opportunity to service your flow measurement and control requirements with a Brooks
Instrument device. Every day, flow customers all over the world turn to Brooks Instrument for solutions to their
gas and liquid low-flow applications. Brooks provides an array of flow measurement and control products for
various industries from biopharmaceuticals, oil and gas, fuel cell research and chemicals, to medical devices,
analytical instrumentation, semiconductor manufacturing, and more.
The Brooks product you have just received is of the highest quality available, offering superior performance,
reliability and value to the user. It is designed with the ever changing process conditions, accuracy requirements
and hostile process environments in mind to provide you with a lifetime of dependable service.
We recommend that you read this manual in its entirety. Should you require any additional information concerning
Brooks products and services, please contact your local Brooks Sales and Service Office listed on the back cover
of this manual or visit www.BrooksInstrument.com
Yours sincerely,
Brooks Instrument
Installation and Operation Manual
X-SE-0250-Series-eng
Part Number: 541B129AAG
October, 2017
0250 Series
THIS PAGE WAS
INTENTIONALLY
LEFT BLANK
i
Contents
Installation and Operation Manual
X-SE-0250-Series-eng
Part Number: 541B129AAG
October, 2017
0250 Series
Paragraph Page
Number Number
Section 1 Introduction
1-1 Description .................................................................................................................................1-1
1-1-1 Architecture................................................................................................................................1-1
1-1-2 Communication .......................................................................................................................... 1-1
1-1-3 Process Controls .......................................................................................................................1-1
1-1-4 Operator Controls and Indicators...............................................................................................1-2
1-1-5 Diagnostic Capabilities...............................................................................................................1-2
1-2 Specifications (Reference Table 1-1) ......................................................................................... 1-2
1-3 Signal Wiring (Reference Figures 1-1 and 1-2) .........................................................................1-4
1-4 Optional Equipment ...................................................................................................................1-4
1-4-1 Mounting Kit Options..................................................................................................................1-4
1-4-2 Power Supply Options................................................................................................................1-4
1-4-3 Input/Output Pin-Out Adapters ...................................................................................................1-4
Section 2 Installation
2-1 General ...................................................................................................................................... 2-1
2-2 Receipt of Equipment.................................................................................................................2-1
2-3 Recommended Storage Practice ............................................................................................... 2-1
2-4 Return Shipment ........................................................................................................................ 2-2
2-5 Transit Precautions .................................................................................................................... 2-2
2-6 Removal from Storage ...............................................................................................................2-2
2-7 Ventilation and Mounting Requirements .................................................................................... 2-2
2-8 Cleaning Instructions ................................................................................................................. 2-2
2-9 Cable Requirements .................................................................................................................. 2-3
2-10 Installation Instructions .............................................................................................................. 2-3
2-10-1 Panel Mount Installation Instructions .........................................................................................2-3
2-10-2 Table Top Stand Assembly Instructions......................................................................................2-5
2-10-3 Retrofit to Model 0152/0154 Table Top Housing (Model 0254 only)...........................................2-7
2-10-4 19-in. Rack Assembly and Installation Instructions (Model 0254 only) ...................................... 2-8
Section 3 Operation
3-1 Home Screen............................................................................................................................. 3-1
3-2 Operating Controls..........................................................................................................
........... 3-2
3-2-1 Primary Functions ......................................................................................................................3-2
3-2-2 Key Functions ............................................................................................................................3-3
3-3 Navigation ..................................................................................................................................3-4
3-3-1 Display or Instrument Configuration Screen Selection...............................................................3-4
3-3-2 User Interface Screen Map........................................................................................................3-5
3-4 Process Values (PV) and Setpoints (SP) ...................................................................................3-7
3-4-1 PV-SP Measures and Status......................................................................................................3-7
3-4-2 PV-SP Configuration ..................................................................................................................3-8
3-4-3 Value Programming ...................................................................................................................3-9
3-5 Global Settings.......................................................................................................................... 3-12
3-5-1 Global Information.....................................................................................................................3-12
3-5-2 Global System Power................................................................................................................3-13
3-5-3 Global Control Services ............................................................................................................ 3-14
3-5-4 Global Communication.............................................................................................................. 3-15
3-6 Instrument Configuration and Control ....................................................................................... 3-15
3-6-1 Rate (Setpoint) Control .............................................................................................................3-15
0250 Series
ii
Contents
Installation and Operation Manual
X-SE-0250-Series-eng
Part Number: 541B129AAG
October, 2017
Paragraph Page
Number Number
3-6-2 PV Configuration....................................................................................................................... 3-17
3-6-3 Batch Control ............................................................................................................................3-18
3-6-4 Blend Control (Model 0254 only)............................................................................................... 3-19
3-6-4-1 Blend Control Setup .................................................................................................................. 3-20
3-6-4-2 Start Blend ................................................................................................................................ 3-21
3-6-4-3 Terminate Blend In-Process...................................................................................................... 3-22
3-6-5 SP VOR (Valve Override) Function ...........................................................................................3-22
3-6-6 Totalization ................................................................................................................................ 3-23
3-6-7 Emergency Off.......................................................................................................................... 3-24
Appendix A Engineering Units
Available Engineering Units .......................................................................................................A-1
Appendix B Blending Examples
Examples 1 through 6 ................................................................................................................B-1
Appendix C Serial Communications Protocol
C-1 Overview ....................................................................................................................................C-1
C-2 Communication Settings ............................................................................................................C-1
C-2-1 RS232 Port Settings ..................................................................................................................C-1
C-2-2 Hyperterminal Set-Up ................................................................................................................C-2
C-3 Serial Command Organization...................................................................................................C-3
C-3-1 Command Structures .................................................................................................................C-3
C-3-2 Command Addressing................................................................................................................C-6
C-4 Command Operation..................................................................................................................C-7
C-4-1 General Commands...................................................................................................................C-7
C-4-1-1 Command Syncronize................................................................................................................C-7
C-4-1-2 Menu Command ........................................................................................................................C-7
C-4-1-3 View Programmed Channel Port Values ....................................................................................C-8
C-4-1-4 Identify Command......................................................................................................................C-8
C-4-1-5 Message Serial Character Pacing Controls ...............................................................................C-9
C-4-1-6 Serial Message Error Control....................................................................................................C-10
C-4-2 Channel Input Port Commands.................................................................................................C-11
C-4-2-1 Measure Channel Values Command ........................................................................................C-
11
C-4-2-2 Send Channel Input Port Programmed Values .........................................................................C-12
C-4-2-3 Program Channel Input Port Values..........................................................................................C-13
C-4-2-4 Clear Accumulated Values ........................................................................................................C-13
C-4-3 Channel Output Port Control Commands .................................................................................C-13
C-4-3-1 Channel Control Output Port Values .........................................................................................C-13
C-4-3-2 Batch and Blend Control Commands........................................................................................C-14
C-4-4 Global Settings Services...........................................................................................................C-16
C-4-4-1 Global Setting Values................................................................................................................C-16
C-4-4-2 Set Global Settings Values........................................................................................................C-16
C-4-5 Communication Message Basics..............................................................................................C-16
C-4-5-1 Message Structure ....................................................................................................................C-17
C-4-5-2 Message Format.......................................................................................................................C-17
iii
Contents
Installation and Operation Manual
X-SE-0250-Series-eng
Part Number: 541B129AAG
October, 2017
0250 Series
Paragraph Page
Number Number
C-5 Serial Value Programming ........................................................................................................C-18
C-5-1 Read a Programmed Value.......................................................................................................C-18
C-5-2 Program a New Value ...............................................................................................................C-19
C-5-3 Channel Input Port Values ........................................................................................................C-20
C-5-4 Channel Output Port Values......................................................................................................C-22
C-5-5 Global Setting Values................................................................................................................C-23
Appendix D CE Essential Instructions
Essential Instructions .................................................................................................................D-1
Warranty, Local Sales/Service Contact Information....................................................................... Back Cover
Figures
Figure Page
Number Number
1-1 Model 0251 Signal Wiring ..........................................................................................................1-5
1-2 Model 0254 Signal Wiring ..........................................................................................................1-5
2-1 Panel Mount Cut-Out Dimensions ............................................................................................. 2-4
2-2 Table Top Stand Mount Installation ............................................................................................ 2-6
2-3 Power Supply Bracket and Bezel...............................................................................................2-9
2-4 Rack Installation.........................................................................................................................2-9
3-1 Home Screen............................................................................................................................. 3-1
3-2 Model 0251 - User Interface Screen Map ..................................................................................3-5
3-3 Model 0254 - User Interface Screen Map ..................................................................................3-6
Tables
Table Page
Number Number
1-1 Specifications - 0250 Series.......................................................................................................1-3
3-1 Display Home Screen Fields...................................................................................................... 3-1
0250 Series
iv
Contents
Installation and Operation Manual
X-SE-0250-Series-eng
Part Number: 541B129AAG
October, 2017
THIS PAGE WAS
INTENTIONALLY
LEFT BLANK
1-1
0250 Series
Section 1 Introduction
Installation and Operation Manual
X-SE-0250-Series-eng
Part Number: 541B129AAG
October, 2017
1-1 Description
The Brooks Model 0250 Series is a versatile full-featured measurement
and control process instrument, available with single or multiple channel
capabilities. The architecture supports a wide range of operating
capabilities organized to meet the requirements of nearly any high-
accuracy measurement and control application.
This system suits applications requiring advanced single & multiple
channel operation. It provides control services including rate, batch, and
proportional blending.
The system is all digital, based on microcomputer technology. There is no
power switch to be left off, no feature selection switches or jumpers, and
no analog trimming potentiometers.
It employs surface mount technology and incorporates floating-point digital
signal processing arithmetic. Built-in test capabilities enable simple
installation, and extensive self-tests ensures long-term operating reliability.
The rugged package is modular, providing an ideal solution for use in
demanding applications and tough environments. Options are available for
panel mount, desktop & rack mount (0254 only).
1-1-1 Architecture
The system is built on the basics of a multiple-port based architecture,
modularly organized, which are combined as channels, able to meet
present and future instrumentation requirements.
Channel(s) provide for value measurements and quantity accumulation,
rate measurements, scalar measurements, supported by value scaling for
process voltage and current process signals. Signal acquisition uses digital
signal processing rejecting ambient noise and interference.
1-1-2 Communication
The communication facilities provide for data acquisition, command, and
control functions, supporting configuration programming and information
gathering.
Communication is initiated by command (solicited), alarms (unsolicited) &
real time scheduled reporting using its internal date-time clock.
1-1-3 Process Controls
Totalizer, batch, and proportional blending (0254 only) are readily achieved
using the front panel key controls or serial commands.
1-2
0250 Series
Section 1 Introduction
Installation and Operation Manual
X-SE-0250-Series-eng
Part Number: 541B129AAG
October, 2017
1-1-4 Operator Controls and Indicators
The instrument has no power switch to be accidently turned off. Operation
may be completely controlled from its integral eight-key pad used to view
operation and programmed operating values. Key activations are single
touch with hold-and-repeat capability. The front panel key pad provides
splash proofing and environment protection.
The 0250 Series primary indicator is its large back lit liquid crystal graphic
display - visible at a distance even in low light conditions - to view values,
support programming operations, and indicate process state information. A
user-selectable audio indicator annunciates key activations.
1-1-5 Diagnostic Capabilities
Powerful automatic diagnostics support easy installation and ensure a
trouble-free operating life. Tests include memory facility scans, channel
input-output status, and communication status.
1-2 Specifications (Reference Table 1-1)
1-3
0250 Series
Section 1 Introduction
Installation and Operation Manual
X-SE-0250-Series-eng
Part Number: 541B129AAG
October, 2017
Table 1-1 Specifications - 0250 Series
PerformancePerformance
PerformancePerformance
Performance
DisplayDisplay
DisplayDisplay
Display 0251: 8 line x 20 character back-lit LCD display.
0254: 8 line x 40 character back-lit LCD display.
ControlsControls
ControlsControls
Controls Keypad: 8-Key metal dome tactile push buttons with selectable audio beep for setpoint (rate, batch, blend),
VOR, emergency stop, full operation and programming.
Date RetentionDate Retention
Date RetentionDate Retention
Date Retention Non-volatile ram/rom, 100 year retention.
Power InputPower Input
Power InputPower Input
Power Input Voltage: 12-24 Vdc required, -15 Vdc permitted.
Current: 400 mA max. current draw per channel.
Instrument power draw: 0.8 Watts.
Optional power module: 100-240 Vac, 47-63Hz.
Power OutputPower Output
Power OutputPower Output
Power Output +15 V/2.0 A, -15 V/1.0 A or 12-24 Vdc/2.0 A.
Signal InputSignal Input
Signal InputSignal Input
Signal Input 0(1)-5 Volts, 0(2)-10 Volts, 0(4)-20 mA.
Signal OutputSignal Output
Signal OutputSignal Output
Signal Output 0(1)-5 Volts, 0(2)-10 Volts, 0(4)-20 mA.
CommunicationsCommunications
CommunicationsCommunications
Communications Full communications capability for remote readout, setpoint, control, programming and data acquisition via RS232.
EnclosureEnclosure
EnclosureEnclosure
Enclosure ABS cycolac resin.
Mounting OptionsMounting Options
Mounting OptionsMounting Options
Mounting Options Panel mount kit, table top kit, rack mount kit, rack mount kit with 19” sub-rack. (Rack mount available for 0254 only)
DimensionsDimensions
DimensionsDimensions
Dimensions See product dimensions on pages 4 - 6.
Temperature/HumidityTemperature/Humidity
Temperature/HumidityTemperature/Humidity
Temperature/Humidity Operating: 32-122°F (0-50°C), 0-95% non-condensing.
Ship/Storage: (-)40-185°F (-)40-85°C, 0-95% non-condensing.
CertificationsCertifications
CertificationsCertifications
Certifications CE Mark
EMC Directive 2014/30/EU EN:61326-1:2013
Low Voltage Directive 2014/35/EU EN:61010-1-2010
Machinery Directive 2006/42/EC EN/ISO:13849-1:2009, EN:60204-1:2009
RoHS Directive 2011/65/EU
FCC Part 15 Class A, part 68
UL-USA & Canada 0254: UL 61010 Electrical Safety for General Purpose Indoor Use.
1-4
0250 Series
Section 1 Introduction
Installation and Operation Manual
X-SE-0250-Series-eng
Part Number: 541B129AAG
October, 2017
1-3 Signal Wiring (Reference Figures 1-1 and 1-2)
1-4 Optional Equipment
1-4-1 Mounting Kit Options
The 0250 Series can be mounted using the following kits:
Panel Mount Kit: Brackets accept panel thickness up to 0.25 in. (6.35 mm).
Table Top Kit: Weighted base with fixed tilt for easy viewing.
Rack Mount Kit: Hardware for mounting the Model 0254 and optional
power supply into 19-in. sub-rack.
Rack Mount Kit with 19-in. sub-rack: 19-in. sub-rack included with Rack
Mount Kit (Model 0254 only).
Retrofit Applications, Model 0152/0154: Rack Mount Kit will adapt the
Model 0254 and power supply to the table top enclosure used for the
Model 0152/0154.
1-4-2 Power Supply Options
The 0250 Series supports the following power supply options:
• Factory supplied: +15 Vdc/2 A, –15 Vdc/1 A, 100–240 Vac, 47–63 Hz
• Factory supplied: +24 Vdc/2.5 A, 100–240 Vac, 47–63 Hz
• User supplied: 12–24 Vdc into 9-pin D connector, 5 A rated
1-4-3 Input/Output Pin-Out Adapters
The Model 0251 has one 15-pin female D-channel connector.
The Model 0254 has four 15-pin female D-channel connectors. The pin
configuration is compatible with standard Brooks 0(4)-20 mA cables.
An optional pin-out adapter kit with four adapters is available for use with
Brooks 0(1)-5 Vdc cables.
1-5
0250 Series
Section 1 Introduction
Installation and Operation Manual
X-SE-0250-Series-eng
Part Number: 541B129AAG
October, 2017
Figure 1-1 Model 0251 Signal Wiring
Figure 1-2 Model 0254 Signal Wiring
1-6
0250 Series
Section 1 Introduction
Installation and Operation Manual
X-SE-0250-Series-eng
Part Number: 541B129AAG
October, 2017
THIS PAGE WAS
INTENTIONALLY
LEFT BLANK
2-1
0250 Series
Section 2 InstallationInstallation and Operation Manual
X-SE-0250-Series-eng
Part Number: 541B129AAG
October, 2017
2-1 General
This section provides installation instructions for the 0250 Series Gas and
Liquid Mass Flow Secondary Electronics device.
2-2 Receipt of Equipment
When the equipment is received, the outside packing case should be
checked for damage incurred during shipment. If the packing case is
damaged, the local carrier should be notified at once regarding his liability.
A report should be submitted to the nearest Brooks Instrument location
listed on the Global Service Network page on our website:
BrooksInstrument.com/GlobalSupportCenters
2-3 Recommended Storage Practice
If intermediate or long-term storage of equipment is required, it is
recommended that the equipment be stored in accordance with the
following:
Within the original shipping container.
Stored in a sheltered area, preferably a warm, dry, heated warehouse.
–40 to 185°F (–40 to 85°C); 0 to 95% non-condensing.
Upon removal from storage, a visual inspection should be conducted to
verify the condition of equipment is "as received".
2-2
0250 Series
Section 2 Installation Installation and Operation Manual
X-SE-0250-Series-eng
Part Number: 541B129AAG
October, 2017
2-4 Return Shipment
Prior to returning any instrument to the factory for any reason, visit our
website for instructions on how to obtain a Return Materials Authorization
Number (RMA #) and complete a Decontamination Statement to
accompany it: BrooksInstrument.com/Service. All instruments returned to
Brooks also require a Material Safety Data Sheet (MSDS) for the fluid(s)
used in the instrument. Failure to provide this information will delay
processing of the instrument.
2-5 Transit Precautions
To safeguard against damage during transit, transport the instrument to the
installation site in the same container used for transportation from the
factory if circumstances permit.
2-6 Removal from Storage
Upon removal from storage, a visual inspection should be conducted to
verify the condition of the equipment is “as received.”
2-7 Ventilation and Mounting Requirements
Because of their low power consumption, the 0250 Series devices do not
have ventilation requirements. However, the ambient temperature
surrounding the 0251 Series devices should not exeed 122°F (50°C). The
optional power supply modules are also ventilation-free and limited to an
ambient temperature of 122°F (50°C).
2-8 Cleaning Instructions
Do not use cleaning agents other than water because this might affect
color and marking of the equipment.
Use a clean, soft and damp cloth for cleaning.
2-3
0250 Series
Section 2 InstallationInstallation and Operation Manual
X-SE-0250-Series-eng
Part Number: 541B129AAG
October, 2017
2-9 Cable Requirements
For compliance with the EMC directive 89/336/EEC, the equipment has to
be installed with shielded signal cables which are overall completely
screened with a shield of at least 80%. Sub-D connectors used must be
shielded with a metal shield. The cable screen should be connected to the
metal shell and shielded at both ends over 360°. The shield should be
terminated to earth ground.
The optional power supplies available from Brooks are always supplied
with a power cord that meets all agency certifications and has a protective
conductor for grounding purposes. Any replacement cords must have
similar construction and be certified by a recognized nartional test
laboratory.
2-10 Installation Instructions
Do not use cleaning agents other than water because this might affect
color and marking of the equipment.
2-10-1 Panel Mount Installation Instructions
1. Cut a hole according to the cut-out dimensions shown in Figure 2-1 .
2. Pass the 0250 Series device enclosure through the cut-out.
3. Position one of the two brackets included in the Panel Mount kit on the
side of the enclosure, while aligning the two holes at the top and bottom
of the bracket flange with the holes at the corners of the back of the
enclosure. Secure the bracket to the enclosure with two of the screws
provided in the kit.
Do not over-tighten these attachment screws.
CAUTION
!
4. Secure the second bracket to the other side of the enclosure.
5. Tighten the panel mounting screws in the middle of both brackets to
secure the enclosure to the panel.
Do not over-tighten these attachment screws.
CAUTION
!
6. Connect the power supply cable with the D-connector to the power
connector on the back of the enclosure.
7. Connect the power supply AC cord to a power outlet.
8. Connect the cables to the RS232 and Channel connectors, as
approprate for the application.
2-4
0250 Series
Section 2 Installation Installation and Operation Manual
X-SE-0250-Series-eng
Part Number: 541B129AAG
October, 2017
Figure 2-1 Panel Mount Cut-Out Dimensions
Model 0251
Model 0254
2-5
0250 Series
Section 2 InstallationInstallation and Operation Manual
X-SE-0250-Series-eng
Part Number: 541B129AAG
October, 2017
2-10-2 Table Top Stand Assembly Instructions
1. Attach the four rubber mounting feet to the base, as shown in
Figure 2-2.
2. Use four of the provided screws to attach the two brackets to the base.
3. Slide the 0250 Series device enclosure into the brackets.
4. Use four screws to secure the enclosure to the brackets.
Do not over-tighten these attachment screws.
CAUTION
!
5. Connect the power supply cable with the D-connector to the power
connector on the back of the enclosure.
6. Connect the power supply AC cord to a power outlet.
7. Connect the cables to the RS232 and Channel connectors, as
approprate for the application.
2-6
0250 Series
Section 2 Installation Installation and Operation Manual
X-SE-0250-Series-eng
Part Number: 541B129AAG
October, 2017
Figure 2-2 Table Top Stand Mount Installation
Model 0251
Model 0254
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98

Brooks 0251 / 0254 Istruzioni per l'uso

Tipo
Istruzioni per l'uso