Pottinger LION 303 CLASSIC Istruzioni per l'uso

Operator‘s manual

Translation of the original Operating Manual

Nr.

Rotary Harrow

LION 253 classic

(Type 8760: + . . 00135)

LION 303 classic

(Type 8761: + . . 00192)

LION 303.12 classic

(Type 8762: + . . 00118)

LION 303 WG

(Type 8771: + . . 00635)

LION 303.12 WG

(Type 8772: + . . 00324)

LION 353.14 WG

(Type 8773: + . . 00045)

LION 403 WG

(Type 8774: + . . 00036)

99+8773.EN.80T.1

1500_GB-PAGE 2

Product liability, information obligation

Product liability obliges manufacturers and dealers to issue operating instructions for the machine at the point of sale and to instruct

the customer on the operation, safety and maintenance regulations governing the machine.

A confirmation is required to verify that the machine and operating instructions have been handed over correctly.

For this purpose

- Document A is to be signed and returned to Pöttinger or via the internet to www.poettinger.at

- Document B remains with the specialist dealer handing over the machine.

- The customer receives document C.

For the purposes of product liability law, every farmer is an entrepreneur.

In the terms of product liability law, damage to property is any damage arising due to the machine, but not to the machine, and an

excess (500 euros) exists for this liability.

Corporate damage to property within the terms of the product liability law is excluded from this liability.

Be advised! The operating instructions must also be handed over with any subsequent machine sale or transfer and the transferee

must be instructed in the regulations stated.

Pöttinger - Trust creates Afﬁ nity - since 1871

"Quality pays for itself." Therefore we apply the highest quality standards to our products which are constantly monitored by our

in-house quality management and our management board. Because the safety, perfect function, highest quality and absolute

reliability of our machines in operation are the core competencies for which we stand.

There may be deviations between these instructions and the product as we are constantly developing our products. Therefore no

claims may be derived from the data, illustrations and descriptions. Please contact your Specialist Service Centre for any binding

information about specific features of your machine.

We would ask you to please understand that changes to the scope of supply with regard to form, equipment and technical

specifications are possible at any time.

Any form of reprint, translation or reproduction, including excerpts, requires the written approval of Pöttinger Landtechnik GmbH.

All rights according to copyright laws remain expressly reserved by Pöttinger Landtechnik GmbH.

Refer to PÖTPRO for additional information about your machine:

Are you looking for suitable accessories for your machine? No problem! All the information you require is here at your disposal.

Scan the QR code on the machine's type plate or look under www.poettinger.at/poetpro

And if we don't have what your looking for, then your Specialist Service Centre is there for you with help and advice.

Dokument D

GB-0600 Dokum D Anbaugeräte - 3 -

PÖTTINGER Landtechnik GmbH

Industriegelände 1

A-4710 Grieskirchen

Tel. 07248 / 600 -0

Telefax 07248 / 600-2511

❑ Machine checked according to delivery note. All attached parts removed. All safety equipment, drive shaft and operating

devices at hand.

❑ Operation and maintenance of machine and/or implement according to operating instructions explained to the customer.

❑ Tyres checked re. correct pressure.

❑ Wheel nuts checked re. tightness.

❑ Drive shaft cut to correct lenght.

❑ Correct power-take-off speed indicated.

❑ Fitting to tractor carried out: to three-point linkage

❑ Trial run carried out and no defects found.

❑ Functions explained during trial run.

❑ Pivoting in transporting and operating position explained.

❑ Information given re. optional extras.

❑ Absolute need to read the operating manual indicated.

Please check. X

According to the product liability please check the above mentioned items.

INSTRUCTIONS FOR

PRO DUCT DELIVERY

EN

In order to prove that the machine and the operating manual have been properly delivered, a confirmation is necessary.

For this purpose please do the following:

- sign the document A and send it to the company Pöttinger or via the internet to www.poettinger.at

- document B stays with the specialist factory delivering the machine.

- document C stays with the customer.

- 4 -

EN

INTRODUCTION

1700_GB-Introduction

Introduction

Dear Customer

These Operating Instructions are intended to allow you

to familiarise yourself with the implement and provide

you with clear information on safe and correct handling,

care and maintenance. Thus please take the time to read

these Instructions.

These Operating Instructions comprise part of the imple-

ment. They are to be kept at a suitable location and acces-

sible to staff over the entire service life of the implement.

Instructions based on the national provisions regarding

protection against accidents, road traffic and environmental

protection are also to be applied additionally.

Any persons commissioned with the operation, maintenance

or transport of the implement must read and understand

these Instructions, in particular the safety information, prior

to starting work. Any warranty claims lapse on non-obser-

vance of these Instructions.

In case you have questions related to this operation manual

or further questions about this implement, please contact

your dealer.

Care and maintenance performed in good time and scru-

pulously according to the maintenance intervals specified

ensure operational and traffic safety as well as the reliability

of the implement.

Use only the original spare parts and accessories from

Pöttinger or accepted by Pöttinger. For those parts relia-

bility, safety and suitability for Pöttinger machines can be

assured. Warranty claims lapse if non-approved parts are

used. The use of original parts is also recommended after

the warranty period has expired to maintain the performance

of the implement in the long term.

Product liability legislation obliges the manufacturer and

the authorised dealer to issue Instructions when selling

implements and to instruct customers in the use with refer-

ence to the safety, operating and maintenance regulations.

Confirmation in the form of a declaration of transfer is

required to verify that the implement and Instructions have

been transferred correctly. The declaration of transfer was

attached to the implement on delivery.

Every self-employed person and farmer is an entrepreneur

within the meaning of the product liability legislation. In

accordance with the laws of product liability, entrepre-

neurial property damages are excluded from the liability.

All damage to property within the meaning of the product

liability legislation is regarded as damage caused by the

implement but not to the implement.

These Operating Instructions are integral part of the imple-

ment delivery scope. You should therefore hand them over to

the new owner if ownership of the implement is transferred.

Train and instruct the new owner in the regulations stated.

The Pöttinger Service-Team wishes you good luck.

- 5 -

1901_EN-Inhalt_8773

CONTENTS EN

Table of contents

Introduction ................................................................ 4

SYMBOLS USED

CE mark ..................................................................... 6

Safety hints: ............................................................... 6

Position of the warning signs ..................................... 7

TRACTOR REQUIREMENTS

Tractor ........................................................................ 9

Ballast weights ........................................................... 9

Lifting unit (three-point linkage) ................................. 9

Necessary hydraulic connections .............................. 9

Necessary power connections ................................... 9

HITCHING THE IMPLEMENT

Loading information ................................................. 10

Preparing for hitching to the tractor .......................... 10

Safety advice ............................................................11

Hitching the implement .............................................11

Unhitching implement .............................................. 12

TRANSPORT

Safety advice ........................................................... 13

transport position ..................................................... 13

Rotor Speed ............................................................. 15

Working depth .......................................................... 16

Scraper plate of the rollers ....................................... 16

Side boards ...............................................................17

Levelling bars ........................................................... 18

Hydraulic upper link (optional equipment) ............... 19

OPERATION

Operation ................................................................. 20

ROW MARKERS

Row markers (optional equipment) ......................... 21

Install mounted seed drill - Hydrolift ......................... 22

VITASEM 252/302/402 classic................................. 22

Remove mounted seed drill - Hydrolift ..................... 23

Attach mountable seed drill machine - mechanical

upper link ................................................................. 23

VITASEM A / ADD, AEROSEM A /ADD .................. 23

Detach mountable seed drill - mechanical

upper link ................................................................. 25

Attach seed drill - hydraulic upper link ..................... 25

VITASEM A / ADD ................................................... 25

Detach mountable seed drill - hydraulic upper link .. 27

Guide values for the length of the upper link ........... 28

MAINTENANCE AND REPAIR

Advice for general maintenance .............................. 29

Tine change ............................................................. 29

Variant: Rapid tine replacement ............................... 29

PTO shaft guarding .................................................. 29

Cleaning of machine parts ....................................... 30

Cylindrical - angular gears ....................................... 30

Classic - Angular gear ............................................. 30

Bar lubrication .......................................................... 30

Winter storage.......................................................... 30

Disposal of old equipment ....................................... 30

Lubrication chart ...................................................... 31

LION 103 .................................................................. 32

Observe Safety

Points in Supple-

ment A!

TECHNICAL DATA

Technical data .......................................................... 33

Position of type plate................................................ 34

Variations of type plates ........................................... 34

Designated use of the rotary harrow ........................ 34

SUPPLEMENT

SAFETY ADVICE

Lubricants ................................................................ 39

Combination of tractor and mounted implement ...... 44

- 6 -

1801_EN-Sicherheit ANSI

EN

SYMBOLS USED

CE mark

The CE mark, which is affixed by the manufacturer, indicates outwardly that this machine conforms to the engineering

guideline regulations and the other relevant EU guidelines.

EU Declaration of Conformity (see Attachment)

By signing the EU Declaration of Conformity, the manufacturer declares that the machine that

is brought into service complies with all relevant fundamental safety and health requirements.

Safety hints:

These Operating Instructions contain the

following Figures:

DANGER

If you do not follow the instructions in a text section

with this marking, there is a risk of fatal or life-

threatening injury.

• All instructions in such text sections must be

followed!

WARNING

If you do not observe the instructions marked this

way, there is the risk of a severe injury.

• All instructions in such text sections must be

followed!

CAUTION

If you do not observe the instructions marked this

way, there is the risk of an injury.

• All instructions in such text sections must be

followed!

NOTE

If you do not observe the instructions marked this

way, there is the risk of material damage.

• All instructions in such text sections must be

followed!

TIP

The text sections marked in this way provide you with

special recommendations and advise regarding the

economical use of the implement.

ENVIRONMENT

The text sections marked in this way provide practices

and advice on environmental protection.

The features marked as (optional) are only available as

standard with specific implement versions or are only

offered for specific versions as optional equipment or are

only offered in certain countries.

Figures may deviate from your implement in detail and are

to be taken as illustrations of operating principle.

Designations such as right and left always apply as the

direction of travel unless the text or illustrations clearly

show otherwise.

- 7 -

1800_AZB_EN_8773

WARNING SIGNS EN

Position of the warning signs

061-17-06

1 Danger - flying objects; keep safe distance from the machine as long

as the engine is running.

bsb 447 410

2 Danger - stay clear of rotating machine parts

3 Never reach into the crushing danger area as long as parts may move.

4 Not step onto the machine when PTO is connected and engine is running.

- 8 -

1800_AZB_EN_8773

WARNING SIGNS EN

5 Before starting up the machine, read the operation instructions.

6 Note on product liability

- 9 -

1800-GB_Tractor requirements_8773

TRACTOR REQUIREMENTS

EN

Tractor

To operate this machine the following tractor requirements

are necessary:

Tractor power:

LION 253 classic

LION 303 classic

LION 303.12 classic

< 140 PS/103 kW

LION 303WG

LION 303.12 WG

< 180 PS/132 kW

LION 353.14WG

LION 403WG

< 200 PS/147 kW

Hitching: Lower linkage Cat. II or Cat. II

Connections: See table

"Necessary hydraulics and

power connections"

Ballast weights

DANGER

Life hazard or material hazard - due to wrong tractor

ballast distribution.

• The front axle of the tractor must always be

loaded with at least 20 % of the unladen

weight of the tractor to guarantee the steer-

ing and braking capacities of the trailer.

20%

Kg

Lifting unit (three-point linkage)

371-08-16

- The tractor’s lifting unit (three-point linkage) must be

designed for the load that occurs. (See technical data)

- The lifting struts are to be set at the same length (4)

using the appropriate adjusting device

(See the tractor manufacturer’s operating manual)

- If the lifting struts at the lower linkages can be locked

in different positions, then the rear position is to be

selected. This relieves the pressure on the tractor’s

hydraulic system.

- The limiting chains and stabilisers of the lower linkage

(5) are to be adjusted so that lateral movement of the

hitched implements is not possible. (Safety measure

for transportation)

Necessary hydraulic connections

Consumer Single-action

hydraulic connection

Dual action hydraulic

connection

Identification (on

the implement)

Standard

Row marker (variation) X

Hydrolift (variation) X

>X

Necessary power connections

Consumer Pin Volt Power connection

Standard

Lighting 7-pin 12 V DC According to DIN-ISO 1724

- 10 -

1800-EN_Anbau_8773

EN

HITCHING THE IMPLEMENT

Loading information

DANGER

Risk of death when machine drops!

• Do not stand beneath the lifted machine or

the area surrounding it.

• Please also refer this information to other

persons in the danger area of the lifted ma-

chine or the space surrounding it.

The following load attachment points are provided on the

rotary harrow for loading with a crane:

2

1

- Bracket of 3-point attachment (1)

- Left and right outside on the frame of the trailing roller

(2)

(Rotary harrows overall weight see section entitled

"Technical Data")

Preparing for hitching to the tractor

Adjust the lower link brackets of your rotary harrow to the

mounting bracket category of your tractor.

Category II:

Interchange the lower link brackets of your mounting bracket

so that the rocker is inside. Insert the pin with the small

end (KAT II) into the rocker.

Category III:

Interchange the lower link brackets of your mounting

bracket so that the rocker is outside. Insert the pin with

the big end (KAT III) into the rocker.

- 11 -

1800-EN_Anbau_8773

HITCHING THE IMPLEMENT EN

Safety advice

NOTE

Property damage - in the event of a collision between

cardan shaft and machine.

• Check the length of the cardan shaft before

ﬁ rst use.

• Adjust the length of the cardan shaft if

necessary. For details see chapter “Cardan

shaft” in the attachment of this Operating

Instructions.

TIP

The general safety information in the Attachment to the

Operating Instructions is to be observed!

Hitching the implement

Requirement:

Check the suitability of your tractor according to the section

located in the attachment entitled “Important Additional

Information for Your Safety” before attaching the rotary

harrow to the tractor.

WARNING

Risk of serious injury - by squeezing or body parts

being trapped between tractor and machine!

• Please relegate every person from the

danger area of the coupling points on the

machine before driving up the tractor to the

machine.

Hitching:

- Prepare the tractor lifting mechanism according to the

Chapter "Tractor requirements"

WARNING

Risk of serious injury - by squeezing or body parts

being trapped between tractor and machine!

• Secure the tractor against rolling

• Stop the engine.

• Remove the key

before making the danger area between tractor and

machine accessible again.

345

- Connect and secure lower linkage to the pendular

compensators (3). The pendular compensators (3) can

be moved horizontally via the hole pattern (5) and are

to be adapted to the tractor.

- Connect upper link and secure. (4)

- Connect cardan shaft.

The overload security of the cardan shaft is to be coupled

with the connection of the accessory equipment

- Connect the 7-pin plug of the lighting to the tractor.

- Connect the hydraulic hoses depending on equipment.

WARNING

Risk of serious injury - by squeezing or body parts

being trapped between tractor and machine!

• Please relegate every person from the

danger area of the coupling points on the

machine before operating the hydraulic lift of

the tractor.

- 12 -

1800-EN_Anbau_8773

HITCHING THE IMPLEMENT EN

Unhitching implement

TAKE NOTE

Property damage - due to the machine sinking on

unsuitable grounds.

• Only park the machine on ﬂ at, ﬁ rm ground!

Requirement:

Only park the rotary harrow on firm, level ground! Ensure

there is enough clear space to make it easy to re-attach

the rotary harrow to the tractor.

Unhitching:

- Disconnect the 7-pin plug of the lighting at the tractor.

- Disconnect hydraulic hoses depending on equipment.

- Disconnect cardan shaft

- Relieve and disconnect upper linkage.

- Disconnect lower linkage and carefully drive the tractor

forwards.

- Secure implement with the anti-theft device

1. Install anti-theft device on the mounting

2. Secure the anti-theft device with a padlock.

Lower linkage mounting

- 13 -

1800-GB_Transport_8773

TRANSPORT

EN

Safety advice

DANGER

Life hazard - due to falling off from the implement

during the drive.

• Do not give permission to anyone to ride on

the rotary harrow or to climb on the running

rotatary harrow.

transport position

TIP

Observe the country-specific regulations! (especially for

the transport width of LION 353.14 WG and of the LION

403 WG when hitched!)

See Attachment C - statutory information on hitched

implements drawn by towing vehicles in road traffic.

Requirement:

The transport width of the rotary harrow LION 303 can

be reduced to less than 3 m. The transport height varies

depending on equipment.

Adjusting to transport height:

Version WG:

- Unlock, fold up and secure the side sheets (1).

- Check the functioning of the lighting or, for

- LION 353.14 and LION 403: e.g. load on the trailer

1

Version classic:

- Unlock, fold up the side sheets (1) and secure for (2).

- Check the functioning of the lighting

2

1

Row markers (optional) only for version WG

- Swivel up the row markers and secure (2).

(For details see Chapter "Row markers")

2

TIP

For the version with hydraulic upper link, the sowing

machine can be inclined to the front. Thus the gravity

centre of the tractor-trailer combination is moved in the

direction of the tractor.

- 14 -

1800-GB_Transport_8773

TRANSPORT

EN

Variant: Hitched or attached seed drill

- The hitched or attached seed drill may increase the

transport dimension of the overall working unit.

- The transport information for the hitched or attached

seed drill must also be observed.

(see Operating Instructions "Seed drill")

- for the attached seed drill with hydrolift and lifting limiter

the lifting limiter is to be locked in transport position.

Close ball cock (3)

- Reopen the ball cock (3) in working position to allow

the function of the lifting limiter

3

- 15 -

1800-GB_Settings_8773

SETTINGS

EN

Rotor Speed

Requirement:

The speed of the rotors may be pre-selected depending on

the tractor power and ambient conditions. This is carried

out either by way of the pre-selected PTO drive shaft speed

of the tractor or by the position of the gearwheels in the

rotary harrow’s transmission.

PTO shaft speed:

The recommended speed of the tractor’s PTO drive shaft

is 1,000 rpm. The lowest torque occurs at this speed and

this protects the drive components.

The speed of the tractor’s PTO drive shaft may be reduced

to 750 rpm or 540 rpm on soft ground or with a low working

depth.

Reposition the gears in the transmission of the

rotary harrow (only version WG):

- Lift the rotary harrow and incline it with the upper link

as much as possible to minimise oil leakage.

DANGER

Risk of death - in the event of unpredictable

movements of tractor or machine

• Secure the tractor against unintentional

rolling.

• Stop the engine.

• Remove the key.

• Secure the machine against falling with

support elements (1).

1

NOTE

Material hazard - due to leaking oil

• Before opening the transmission cover put

a tub underneath the transmission to collect

any possibly leaking oil.

TAKE NOTE

Material hazard - due to staining of the gear

• When the transmission is open, pay atten-

tion to cleanliness and to not let any dirt

inside the transmission.

- Unscrew the transmission cover (2).

2

- Insert the gears according to the table above.

- Screw the transmission cover (2) and check that it is

tight.

- Check the transmission oil level and if necessary refill.

(For details see chapter "Maintenance")

Table: Rotations of the spin top during the

articulated shaft rotations: (only version classic)

Transmission classic:

U/min articulated

shaft

U/min spin top at

transmission rotation:

540 185

750 257

1,000 342

- 16 -

1800-GB_Settings_8773

SETTINGS

EN

Working depth

TIP

It is recommended that the adjustment devices are cleaned

to facilitate the adjustments.

The working depth of the rotary is determined by the pivot

arc of the attached roller. The pivot arc is limited upwards

by the marking position of the bolts in the frame’s hole on

the right and left-hand sides.

Setting:

-Raise rotary harrow

The roller lowers and the bolts are relieved.

DANGER

Risk of death - in the event of unpredictable

movements of tractor or machine

• Secure the tractor against unintentional

rolling.

• Stop the engine.

• Remove the key.

• Secure the machine against falling with

support elements (1).

1

- Release the bolts (2) and lock in the required position.

TIP

The working depth closely depends on the soil conditions.

2

Lowest position (A)= smallest working depth

Top position (B) = greatest working depth

173-12-02

A

B

The working depth changes by approx. 2.5cm per hole

- Lock the bolts (2) left and right at the same position!

- Secure the bolts (2).

Scraper plate of the rollers

TIP

It is recommended that the adjustment devices are cleaned

to facilitate the adjustments.

The scraper plates clean the rollers of dirt.

Setting:

(for all rollers with wiper except for cutting packing rollers)

-Raise rotary harrow

The roller is free and the roller freewheel can be tested.

DANGER

Risk of death - in the event of unpredictable

movements of tractor or machine

• Secure the tractor against unintentional

rolling.

• Stop the engine.

• Remove the key.

• Secure the machine against falling with

support elements (1).

1

- 17 -

1800-GB_Settings_8773

SETTINGS

EN

- Loosen bolts (2) on both sides

- The wear of the scraper plates can be re-adjusted with

the bolt (3).

- Re-tighten bolts (2) !

23

TIP

Only re-adjust the scraper plates to the extent that the

freewheel of the roller is not hindered by the scraper

plate. If necessary, the scraper plates can be adjusted

individually, by loosening the bolt (4) and moving the

scraper plate in the slot.

4

Setting:

for the cutting packing rotor

1. Loosen bolts (6) (7)

2. Using a lever (e.g.: screw driver) in bush (5) turn the

bar at the pivot point (7).

3. Re-tighten bolts (6) (7).

5

7

6

TIP

Only re-adjust the scraper plates to the extent that the

freewheel of the roller is not hindered by the scraper

plate. If necessary, the scraper plates can be adjusted

individually, by loosening the bolt (4) and moving the

scraper plate in the slot.

4

Side boards

DANGER

Life hazard - due to side shields not being folded

down properly

• First, fold down the side shields and only

then switch on the motor of the drive.

• Please always repair faulty side shields.

The side shields screen access to the outer processing tines

in the working position and support preparation of the seed

bed in that the soil processed cannot escape to the side.

Changing from working into transport position:

Version WG:

The side shields may be pivoted into the transport position to

reduce the rotary harrow’s transport width to less than 3 m.

- Remove the bolts (1) from the side shield

- Lift the side shield completely and secure it in transport

position with the bolts (1)

1

- 18 -

1800-GB_Settings_8773

SETTINGS

EN

Version Classic:

The side shields may be pivoted into the transport position to

reduce the rotary harrow’s transport width to less than 3 m.

- Remove the bolts (1) from the side shield in working

position

- Lift the side shield completely and secure it in transport

position with the bolts (2)

2

1

2

Setting of the transport position with the help of

the parallelogram: (only version WG)

The shield guidance is additionally equipped with a

parallelogram if the rotary harrow is fitted with a row marker

or if it is combined with a seed drill attachment.

Setting the shield height in working position:

Version WG:

The shield height should be set so that it slides about 1-2

cm deep through the ground when it is used.

The shield position may be adjusted according to the

ambient conditions (e.g. crop residues).

- Open screws (2)

- Set the position you wish in the slotted hole

- Tighten screws (2)

2

Version classic:

The shield height should be set so that it slides about 1-2

cm deep through the ground when it is used.

The shield position may be adjusted according to the

ambient conditions (e.g. crop residues).

- Open screws (2)

- Set the position you wish in the slotted hole

- Tighten screws (2)

2

Levelling bars

DANGER

Danger to life due to moving gyros during work on

the levelling bar

• Switch off the motor before working on the

levelling bars.

• Remove the key.

The rotary harrow is equipped as standard with a rear

bar and on request with a front bar. The levelling bars are

height adjustable.

- 19 -

1800-GB_Settings_8773

SETTINGS

EN

Setting trimming bar:

- Take the cam lever (auxiliary means for easier

adjustment) from the parking position (1)

1

- Insert the can lever (2) in the first free hole on the

levelling bar arm and swivel until the bolt (3) is free of

load and can be taken out.

3 2

- Continue lever swivelling until the levelling bar can be

taken out through the next hole with the bolt (3).

- Repeat the procedure until the levelling bar has reached

the chosen position.

- Take out the cam lever and place it in parking position

(1)

Setting front bar:

- Like with the trimming bar, follow the holes on the

levelling bar arm (4)

4

Hydraulic upper link (optional

equipment)

Operation:

- by means of the double-acting hydraulic system of the

tractor set the inclination angle of the sowing machine.

- On headlands you can lift the sowing machine separately

so as to permit field harrowing without sowing.

- In road transport position the gravity centre of the trailer

can be moved in the direction of the tractor by further

inclining the sowing machine in driving direction.

Setting the inclination of the drill

The drill should be standing horizontally or slightly to the

back. To do that, adjust the length of the upper link via the

spindle on the hydraulic cylinder.

Setting:

1. Unhitch harrow from drill (see unhitching of the drill)

2. Remove linchpin (1)

3. Remove bolt (2)

1

2

4. Fold up the upper link

5. Fold away the upper link arm so that the counternut

(3) and the square shaft are easily accessible.

6. Open the counternut (3)

7. Set the spindle length by rotating the rear end (4).

Distance A (between the rear lifting cylinder and the

counternut) must be between 40 mm and 65 mm.

A

3

4

The bigger distance A the more the drill inclines to

the back, in driving direction.

The smaller the distance A the more the drill inclines

to the front, in driving direction.

- 20 -

1800-EN_Einsatz_8773

OPERATION

EN

Operation

DANGER

Life hazard - due to moving parts

• Check the protective devices for complete-

ness.

• First, fold down all protective devices prop-

erly before switching on the drive

• Instruct everyone to leave the danger area

before switching on the drive.

Starting work:

On the field, lower the rotary harrow to just above the soil

and only then bring the PTO drive shaft up to the intended

speed.

Approach with the tractor and lower the rotary harrow

completely whilst doing so.

Turning:

Only raise the rotary harrow as far as necessary for the

turning procedure. If the PTO drive shaft is only angled

slightly in the process, it may continue to run.

The PTO drive shaft must be switched off if the machine

runs noisily in the raised condition.

Blockages:

The PTO drive shaft is equipped with an overload clutch to

intercept any blockages on stony ground or other obstacles

without damaging the rotary harrow.

Removing blockages:

DANGER

Risk of death - in the event of unpredictable

movements of tractor or machine

• Secure the tractor against unintentional

rolling.

• Stop the engine.

• Remove the key.

• Secure the machine against falling with

support elements (1).

1

- stop the tractor

- raise the rotary harrow and simultaneously

lower the rotational speed of the PTO drive shaft.

If the rotors are free from blockages, the cam-type cut-

out clutch of the PTO drive shaft engages again audibly

due to the reduced speed, and work can be continued.

The rotors must be freed of the blockage or obstacle if they

do not start to rotate.

CAUTION

Mild injury risk - due to thrown off parts which are

not covered by the protective cover.

• Refer people out of the danger area.

• Stop drive of the machine as soon as any-

body approaches it.

La pagina sta caricando ...

Pottinger LION 303 CLASSIC Istruzioni per l'uso

Questo manuale è adatto anche per

Pottinger LION 303 CLASSIC Istruzioni per l'uso

in altre lingue

Documenti correlati