Alpina EHT 600 PROXH 600E-PRO Operating Instructions Manual

Categoria
Tagliasiepi a motore
Tipo
Operating Instructions Manual
EHT 600PRO
XH 600E-PRO
Istruzioni per l’uso Prima della messa in funzione leggere le istruzioni perl‘utilizzo!
Operating Instructions Read operating instructions before use!
Manuel d’utilisation Lire attentivement le mode d‘emploi avant chaquemise en service !
Gebrauchsanweisung Vor Inbetriebnahme Gebrauchsanweisung lesen !
Instrucciones de Manejo ¡Lea las instrucciones de manejo antes de efectuar la puerta en marcha!
Instruções de Serviço Antes da colocação em funcionamento leia o manual de instruções!
Èíñòðóêöèÿ ïî ýêñïëóàòàöèè Ïåðåä ïðèìåíåèåì ïðî÷èòàòü èíñòðóêöèþ ïî ýêñïëóàòàöèè!
Instrukcja Obs³ugi Pred pouzitíu cosacky, travy pozorne precitajte návod k jej pouzitíu!
Navod K Pouzitíu Przed uzyciem narzedzia przeczytajcie uwaznie instrukcje uzytkowania!
Uputstvo za uporabu Prije stavljanja u pogon proèitajte uputstvo za uporabu!
ODHGIES CRHSEWS Ðñéí áðü ôçí Ýíáñîç ëåéôïõñãßáò äéáâÜæåôå ôéò ïäçãßåò ÷åéñéóìïý!
Kullanxm Talimatx Çaliätirmadan önce kullanma talimatxnx okuyunuz!
ES
PT
DE
IT
GB
FR
RUS
CZ
HR
GR
PL
TR
1
2
1
3
4
8 mm
6
5
7
2
8
3
9
DE
1+2 Griff (1) und Bügelgriff (2) mit Sicherheitsschalter
3 Schutzschild
4 Netzleitung mit Stecker
5 Sicherheitsmesserbalken
6 Anstoßschutz
GB
1+2 Operating Switches (two-hand operation)
3 Hand Guard
4 Power Cord
5 Blade Safety Rail
6 Impact Protector
FR
1+2 Interrupteur (maniement à 2 mains)
3 Bouclier de protection
4 Câble de secteur avec connecteur
5 Couteaux de sécurité
6 Butée de protection
CZ
1+2 Rukojet s okrouhlou ochranou (1) + Oblouková
rukojet (2) s bezpecnostním spínacem
3 Ochranný štít
4 Prívodní kabel se zástrckou
5 Bezpecnostní nosníky nozu
6 Ochrana proti nárazu
PL
1+2 Uchwyt z przelacznikiem (1)+ Uchwyt kablakowy z
przelacznikiem (2) bezpieczenstwa
3 Tarcza ochronna
4 Kabel przylaczeniowy z wtyczka
5 Belka z nozami
6 Ochrona przed uderzaniem
IT
1+2 Interruttore di servizio (azionamento con due mani)
3 Schermo di protezione
4 Linea di rete con spina
5 Barra con lame di sicurezza
6 Paracolpi
PT
1+2 Interruptor de serviço (manejo de 2 mãos)
3 Placa de protecção
4 Cabo de rede com cha
5 Barra de faca de segurança
6 Protecção de embate
ES
1+2 Interruptor de funcionamiento (manejo a dos manos)
3 Pantalla protectora
4 Cable de enchufe
5 Portacuchillas de seguridad
6 Protección antichoque
GR
1+2 DiakÒpthj asf£leiaj
3 Prostateutik» asp…da
4 Kalèdio me fij
5 Bracionaj macairièn asf£leiaj
6 ProstateutikÒ kroÚsewj
TR
1+2 Elektrxk akxmxnz baålamak onde Gulunan
3 Korunma emnxyetx
4 Elektrxk Kablasu/ Elektrxklx fxñte
5 Emnxyetbiçakxåx
6 Çarpmaemniyet
RUS
1+2 Îñíîâíàÿ ðóêîÿòü (1) è îòêèäíàÿ ðóêîÿòêà (2)
3 Çàùèòíûé êîçûðåê
4 Ñåòåâîé êàáåëü ñî øòåêåðîì
5 Áåçîïàñíûé íîæåâîé áðóñ
6 Ïðîòèâîóäàðíûé ýëåìåíò
HR
1+2 Prednji rukohvat sa sigurnosnom sklopkom (1).
Stražnji rukohvat sa sigurnosnom sklopkom (2).
3 Zaštita za ruke
4
Mrežni vod
5 Posmièni nož
6 Zaštita od udara
4
1 2 3 4 5 6
DE
1 Augen- und Gehörschutz tragen!
2 Warnung!
3 Gebrauchsanweisung lesen!
4 Dieses Elektrowerkzeug nicht dem Regen aussetzen
5 Bei Beschädigung oder Durchschneiden der Anschluß-
leitung sofort Stecker ziehen!
6 Achtung Umweltschutz ! Dieses Gerät darf nicht
mit dem Hausmüll/Restmüll entsorgt werden. Das
Altgerät nur in einer öffentlichen Sammelstelle abge-
ben.
GB
1 Wear eye and ear protection !
2 Warning!
3 Read the instruction manual !
4 Do not use the tool under wet weather conditions !
5 Unplug immediately if the power cord or plug becomes
damage !
6 Attention: Environmental Protection! This device may
not be disposed of with general/household waste.
Dispose of only at a designated collection point.
IT
1 Portare dispositivos per proteggere l’udito e gli cchi!
2 Avvertimento!
3 Leggere le istruzioni sull’uso!
4 Non esporre questo utensile elettrico alla pioggia!
5 In caso di danneggiamento o taglio del cordone di
allacciamento, tirare immediatamente la spina!
6 Attenzione protezione dell’ambiente! Questo apparecchio
non può essere smaltito con la spazzatura domestica/con
rifiuti non riciclabili. Consegnare lapparecchio vecchio
esclusivamente in un punto di raccolta pubblico.
FR
1 Porter des protections des yeux et des oreilles!
2 Attention!
3 Lisez l’instruction de service!
4 Ne pas laisser cet outil électrique sous la pluie!
5 En cas de détérioration ou section du câble
retirer immédiatement la prise!
6 Attention ! Protection de l’environnement! Le présent
appareil ne peut en aucun cas être éliminé avec les
ordures ménagères/déchets. Toujours déposer les
appareils usagés dans un centre de collection.
Illustrazione e spiegazione dei simboli Illustration and explanation of pictograms
Repsentation et explication des pictogrammes Abbildung und Erklärung der Piktogramme
Símbolos y su significado Imagens e Explicações dos Pictogramas
Èçîáðàæåíèå è îáúÿñíåíèå ïèêòîãðàìì Ilustracja i objaœnienia piktogramów
Vyobrazení a vysvìtlivky k typovému štitku
Slike i objašnjenje piktograma
ApeikÒnish kai epex»ghsh twn sumbÒlwn ÇIZIMLER VE ÄEKILLERIN IZAHI
ES
1 Lleve protecciones del oído y de los ojos!
2 Cuidado!
3 Lea las instrucciones de manejo!
4 No exponga esta herramienta eléctrica a la lluvia!
5 Al dañarse o cortarse el cable de red desenchufe
inmediatamente el aparato!
6 Atención: protección del medio ambiente. Este aparato
no debe evacuarse junto a la basura doméstica ni el
rechazo. El aparato, una vez desechado, deberá
entre-garse en un puesto de recolección colectivo.
PT
1 Utilizar uma protecção do ouvido e de olhos!
2 Atenção!
3 Ler as instruções de serviço!
4 Não expor esta ferramenta eléctrica à chuva!
5 Em caso de danificar ou cortar o cabo eléctrico, tire a
fiche de rede imediatamente!
6 Atenção protecção do meio ambiente! Este aparelho
não deverá ser descartado no lixo doméstico/lixo
residual. O aparelho usado deverá ser entregue a um
posto de colecta público.
5
PL
1 Nosiæ ochronniki s³uchu i okulary ochronne.
2 Uwaga!
3 Przed u¿yciem przeczytaæ instrukcjê obs³ugi.
4 Nie dopuszczaæ do kontaktu z wilgoci¹.
5 Odl¹czyæ z sieci jeœli przewód pol¹czoniowy jest
uszkodzony lub przeciêty
6 Uwaga Ochrona œrodowiska naturalnego! Niniejsze
urz¹dzenie nie mo¿e zostaæ usuwane wraz z
odpadami gospodarstwa domowego/odpadami
pozosta³ymi. Zu¿yte urz¹dzenie nale¿y oddaæ w
publicznym miejscu zbiorczym.
CZ
1 Použijte ochranu oèí a sluchu!
2 Varování!
3 Pøeètìte si návod k obsluze!
4 Tento elektrický pøístroj nevystavujte dešti!
5 Pøi poškození nebo pøeseknutí pøívod ního kabelu
ihned odpojte zástrèku!
6 Pozor Ochrana životního prostøedí ! Tento pøístroj
se nesmí likvidovat spolu s domovým/komunálním
odpadem. Vysloužilý pøístroj je zapotøebí odevzdat
do sbìrných surovin.
GR
1 for£te prostateutik£ guali£ kai wtoasp…dej
2 Prosoc»
3 Prin thn crhsimopo…hsh diab£ste tij odhg…ej cr»sewj
4 AutÒ to mhc£nhma na mhn ekte…qete sthn broc»
5 Se per…ptwsh bl£bhj tou kalwd…ou bg£lte to fij apÒ
thn pr…za
6 Ðñïóï÷Þ ðñïóôáóßá ðåñéâÜëëïíôïò! ÁõôÞ ç óõóêåõÞ äåí
åðéôñÝðåôáé íá ðåôá÷ôåß óôá ïéêéáêÜ áðïññßììáôá. Ôçí
ðáëéÜ óõóêåõÞ ôçí ðáñáäßäåôå ìüíï óå Ýíá äçìüóéï êÝíôñï
ðåñéóõëëïãÞò áðïññéììÜôùí.
TR
1 Göz ve kulak koruyuculari taäiyiniz
2 Dikkat !
3 Cihazi kullanmadan evvel kullanim talimatini okuyuuz
4 Bu aleti yaåmur altinda birakmayiniz!
5 Baålanti kablosunun hasar görmesi alin dederhal fiäi
çekiniz.
6 Dikkat çevre korumasý ! Bu cihazýn ev çö/artýk çöp ile
imha edilmesi uygun deðildir. Eski cihaz sadece resmi
bir atýk biriktirme yerine verilebilir.
HR
1 Nositi zaštitu za uši!
2 Upozorenje!
3 Proèitajte uputstvo za uporabu!
4 Ovaj elektrièni alat ne smijete izlagati kiši!
5 Kod ošteæenja ili prerezivanja prikljuènog voda
odmah izvaditi mrežni utikaè!
6 Pozor Zaštita okoliša! Ovaj ureðaj se ne smije
zbrinuti sa kuænim otpadom / preostalim otpadom.
Stari ureðaj se treba predati javnom mjestu za
sakupljanje otpada.
RU
1
Èñïîëüçóéòå î÷êè è íàóøíèêè!
2
Ïðåäóïðåæäåíèå!
3
Ïðî÷òèòå èíñòðóêöèþ!
4
Íå îñòàâëÿéòå èíñòðóìåíò ïîä äîæäåì!
5
Ïðè ïîâðåæäåíèè êàáåëÿ íåìåäëåííî âûíüòå
6 Âíèìàíèå - çàùèòà îêðóæàþùåé ñðåäû! Ýòîò ïðèáîð
íå ðàçðåøàåòñÿ óòèëèçèðîâàòü âìåñòå ñ áûòîâûìè/
ïðîèçâîäñòâåííûìè îòõîäàìè. Ñòàðûé ïðèáîð
ñäàâàòü òîëüêî íà îáùåñòâåííîì ñáîðíîì ïóíêòå.
GB-1
ENGLISH
Hedge Trimmer
2. General safety instructions
Information on noise emission in accordance with
“Machine Noise Information Ordinance 3. GPSGV and
Machinery Directives: the noise pressure level at the
place of work can exceed 85 dB(A). In such cases the
operator will require noise protection (e.g. wearing of
ear protectors).
Attention: Noise protection ! Please observe the local
regulations when operating your device.
General safety instruction
Usage of hedge trimmer always involves a risk
of accidents, therefore please observe the relevant
accident prevention instructions.
The machine has been constructed according to the
latest technology and in accordance with the recog-
nised technical safety regulations. Nevertheless, use
of the machine can involve risks to the user or third
persons, and can cause damage to the machine or
other objects.
Attention: Using electric power tools, you must observe
following fundamental safety instructions to protect
yourself against electric shock, against danger of
injuries and danger of re. Read all these instructions
before using the hedge trimmer and observe them.
Keep these safety instructions at a safe place.
Use the machine in a safety conscious manner for
suitable applications in a technically perfect condition
only and with due regard to the operating instructions!
Immediately rectify or have recti ed any faults which
could adversely affect safety!
This machine may cause serious injuries. Please
read the instruction manual carefully as to the correct
handling, the preparations, the maintenance and the
proper use of the hedgetrimmer. Familiarize your-self
with the machine before the rst use and also have
yourself introduced to practical use of the machine.
3. Application
The machine is only intended for trimming hedges. Use
for any other purpose constitutes inappropriate use. The
manufacturer / supplier is not liable for any injury and/
or damage arising from inappropriate use. This risk
is the sole responsibility of the user.Appropriate use of
the machine also includes adherence to the operating
instructions and compliance with the servicing and
maintenance instructions.
Always keep the instruction manual close at hand
during operation!
4. Safety instruction
1. Keep your working area tidy. Disorder at your
working area may lead to accidents.
2. Please consider environmental infl uences. Do not
expose power tools to rain. Do not use power
tools in wet or moist surroundings. Ensure that
there is good lighting. Do not use power tools
near infl ammable uids or gases.
3. Keep children away. Do not allow other persons
to touch the power tool or cable. Keep other per-
sons out of your working area.
4. Keep your power tools in a safe place. Power tools
that are currently not in use should be stored in a
dry place where they are out of reach of children
(high on a shelf or in a locked place).
5. Do not overtax your power tools. They work better and
safer if used within the stated performance range.
6. Always disconnect the plug from the mains socket
before carrying out any work on the equipment,
before cleaning and before moving the equipment.
7. The use of hedge trimmers involves certain risks.
1. Introducing the hedgetrimmer
Technical data EHT 600PRO / XH 600E-PRO (EHT 600)
Operating Voltage V~ 230
Nominal Frequency Hz 50
Nominal Consumption W
600
Cutting movements min
-1
2400
Shear length mm
600
Cutting Thickness mm 29
Weight (without ex) kg
3,6
* The nominal consumption you will fi nd on the type plate
Noise Pressure Level LpA according to EN 50144 86 dB (A)
Vibration according to EN 50144 < 2,5 m/s
2
Class of protection: II / DIN EN 50144/VDE 0740
Interference suppressed in accordance with EN 55014, EN 61000-3-2:95, EN 61000-3-3:95 .
We reserve the right to make changes to the technical specifi cations.
The devices are manufactured in accordance with the provisions of DIN-EN 50144-1and DIN-EN 50144-2-15 and fully
comply with the provisions of the German Equipment and Product Safety Act.
GB-2
Attention: Danger! Rotating machinery.
8. The hedge trimmer should always be held with
both hands.
9. Before using the equipment clear the working
area of any foreign objects and be aware of
foreign objects during operation of the machine!
If the machine becomes jammed e.g. by thick
branches, switch off and disconnect the ma-
chine from the mains socket before investigating
and rectifying the cause of the jam. Take special
care when switching the machine on again.
10. Check the fl ex and all connections for any visible
faults before using the machine (plug discon-
nected). Do not use a faulty ex.
11. Keep the ex away from the cutting area.
12. Do not use the trimmer in wet weather and do not
use it to cut wet hedges.Do not wash down the
device with water. Do not use any high-pressure
cleaning devices or steam jet devices for cleaning.
13. Carry the trimmer by the handles provided and
keep hands away from the cutting blades.
14. In line with agricultural Trade Association Regu-
lations only persons over the age of 17 may work
on their own with electric hedge trimmers. Use is
permitted for persons over 16 years if the work is
carried out under the supervision of adults.
15. We would recommend that safety clothing is
worn during the work and that eyes, ears, hair,
hands and feet are fully protected. Protective
gloves should also be worn.
16. Ensure that the motor of your hedge shears can
not be switched on by mistake when you put it
down after work or when you are going to clean the
device. Never forget to unplug the mains supply!
17. Check the cutting unit regularly for damage and
if damage is discovered, the cutting unit should
be properly repaired.
18. Be aware of your responsibility as user towards
third parties in the working area.
19. The trimmer must be properly checked and serv-
iced. If the blades get damaged they should only
be exchanged in pairs. In the event of damage
from impact, specialist’s inspection is essential.
20. Only use extension cords that are approved for
outdoor use and that are not lighter than rubber
tube cords type H07 RN-F according to DIN/VDE
0282 with a diameter of at least 1.5 mm
2
. They must
be water spray protected. Damaged cables of this
unit are only to be replaced by a service station
designated by the manufacturer as special tools
are necessary. Equipment which will be used in
different outside locations should be connected
via residual current - operated current breakers.
21. Do not use the cable for purposes it has not
been designed for. Never carry a power tool at its
cable. Do not pull out the plug from the socket
using the cable. Protect the cable from heat, oil
and sharp edges.
22. Ensure that the equipment is stored safely af-
ter use in such a way that the blade cannot be
touched.
23. When using the equipment, hold it securely with
both hands, stand fi rmly and ensure that you have
suf cient working space. There should be no
people, animals or objects within the working area.
Select the cutting height so that the blade does
not make contact with the ground and you can
operate the equipment from a secure position.
24. Take care when transporting the equipment (only
with blade cover!).
25. For initial use of the hedge trimmer we would rec-
ommend that in addition to reading the operating
instructions, you also seek a practical demon-
stration from an expert.
26. Always ensure that all protective devices and
handles are properly tted. Never attempt to use
an incomplete machine.
27. Never try to use an incomplete tool or a tool that has
been modifi ed in a way that has not been approved.
28. Do not allow children to use a power tool.
29. The use of the hedge trimmer is to be avoided if
other persons, above all children, are within the
working area.
30. Familiarize yourself with the working area and pay
attention to possible dangers which you might not
be able to hear due to the noise of the machine.
31. Always pay attention. Take care of what you do.
Do your work sensibly. Do not use a power tool if
you cannot concentrate.
32. ATTENTION ! Only use the accessories or attach-
ments shown in the Operating Instructions. The
use of other add-on tools and accessories may
set up the risk of injury for you.
33. Have your power tools repaired by an appro-priate-
ly qualifi ed electrician only. This power tool complies
with the applicable safety regulations. Repairs must
only be carried out by qualifi ed electricians using
original spare parts; otherwise, accidents may occur
to the user.
5. Before use
Mounting the bow-type handle (Fig. 1)
If there are screws xed to the mounting points, remove these
rst. Then, remove the shear protector and put the bow-type
handle from the front (as shown in Fig. 1) over the shearing
system, and put it into the relief of the hedge shears housing.
(If necessary, pull the lower ends of the handle slightly apart.)
Take care that you do not squeeze the two parts of the bow-
type handle.To fasten the bow-type handle screw the two
included screws through the openings in the handle into the
threaded holes of the housing and fasten them tightly.
Protection shield (Fig. 2)
If screws are fastened to the bottom plate, remove these.
Fasten the hand protector with the two included screws to
the bottom plate.
Power connection
The machine can only be connected to a single-phase a.c.
current connection. The machine is protectively insulated in
accordance with classifi cation II of VDE 0740. Before using
the machine ensure that the mains current agrees with the
operating voltage data on the machine’s identifi cation plate.
Power Circuit Breaker:
Machines which will be used in different outside loca-
GB-3
tions must be connected to a Power Circuit Breaker.
Securing the power supply cable (Fig. 5)
Only use cables (extension ex) that are approved for
outdoor use. The cable diameter must be equal to or bigger
than 1.5mm² for cable lengths up to 75m.
Extension exes with a length of more than 30m reduce
the machine’s output.
6. Instructions for use of the equipment
Do not use the trimmer in rain or for cutting wet
hedges!
Check the hedge trimmer fl ex and its connections
before each and every use for visible signs of damage
(disconnect the power plug)! Do not use a faulty fl ex.
Gloves:
Protective gloves must be worn when using the
hedge trimmer.
7. Switching the hedge shears on/off (Fig.3)
When switching the hedge shears on take a safe stand.
These hedge shears have a two-hand safety switch. To
switch the hedge shears on the bar switch in the handle
(A) and the grip switch of the bow-type handle (B) must
be pushed down.
To switch the device off let go of both
switches. The motor already stops if one of the two switches
is released.
8. Maintenance
Always disconnect the plug from the power socket
before commencing any work on the machine.
Important: Always clean and oil the blades after pro-
longed use of the hedge trimmer. This will greatly affect
the life of the equipment. Damaged cutting units must be
properly repaired immediately.
Clean the shearing blades
with a dry cloth or – in case of heavier dirt – with a brush.
Attention: Danger of injury!
Oiling of the blades should
ideally be carried out using an environmentally friendly
lubricant (Fig. 6).
Sharpening of the blades
The blades generally do not need servicing and do not
require resharpening if used correctly. In order to prevent
injuries caused by the blades when not in use, the sharp-
ened cutting blade should be covered by the blade cover
(Fig. 4). The blades cannot be sharpened by the user
without opening the equipment and the safety mecha-
nism. Resharpening of the blades can therefore only be
carried out at a specialist workshop.
Changing the blades
Only correct installation of the blades will guarantee problem-
free operation and function of the above mentioned safety
feature of the blades. Changing of the blades should therefore
only be carried out at a specialist workshop.
9. Holding the hedge trimmer when in use (Fig. 7)
This equipment will enable you to cut or trim bushes and
hedges easily and comfortably.
Trimming of hedges
- Young shoots are best cut in a scythe move ment.
- Older and stronger hedges are best cut in a sawing
movement.
- Branches, which are too thick for the hedge trimmer,
should be cut with a saw.
- Sides of hedges should be cut upwards in a taper.
In order to achieve an even height
- Fix a guide line at the required height.
- Cut evenly over this guide line.
Expanded working height: If you want to reach higher or if
you to above your heads height (see Fig. 8), you should take
care of the following:
Attention: Take care to have a secure and safe standing
position when working with your hedge shears in order
to avoid slipping and injury. Always keep the shearing
blades away from your body.
10. Optimum safety
The 5 special features two-hand safety switch, quick
blade stop, protective cover, blade safety rail and
impact protector are fi tted to provide the hedge trim-
mer with optimum safety features.
Attention!
If you nd out that safety functions, such as the
2-switch mechanism or the safety stop, are not
functioning while working with the hedge shears,
immediately cease working and take the machine
to a specialised shop for repairing.
Two-hand safety switch
(Fig. 3)
To switch on the hedge trimmer one of the switch bars
on the hand grip (A or B) and the switch on the bow-type
handle (C) must be held down. If one of the switches
is released, the shearing blades will stop after ca. 0.2
seconds.
Quick blade stop
In order to avoid injuries through cuts, the blade will stop in
max. 0.2 sec. when one of the two switches is released.
Blade safety rail
(Fig. 4)
The cutting blade set back from the blade housing reduces
the risk of injuries due to unintentional body contact. As
soon as the hedge trimmer is switched off, the sharp cut-
ting blades will stop - due to safety reasons - exactly under
the cover rail in order to reduce the risk of injuries during
transport.
Impact protector
(Fig. 9)
The extended guide rail prevents unpleasant shocks
(blade recoil) being transmitted to the operator due to
impact with solid objects (wall, ground etc.).
Gear protection feature
If solid objecst are caught in the cutting blade and jam
the motor, switch off the machine at once, disconnect the
power plug from the power socket, remove the object
and continue with the work.
The equipment is also tted with an overload cutout,
which protects the gears against mechanical damage in
the event of blade jams.
GB-4
11. Storing the trimmer after use
The hedge shears must be stored such that there is
no danger of injuries being caused to persons by the
cutting blades!
Important note:
The shearing blades should be cleaned
after each use.
(see also Section 8. Maintenance).
This will
considerably increase the service life of the device. Please
use a lubricator that is not harmful to the environ-ment ,
e. g. our service spray. Then put the shears in their case
with the cutting blades fi rst.
12. Repair service
Repairs to electric power tools should only be carried out
by specialist electrical personnnel.
13. Waste disposal and environmental protection
If your device should become useless somewhere in the
future or you do not need it any longer, do not dispose of
the device together with your domestic refuse, but dis-
pose of it in an environmentally friendly manner.
Please dispose of the device itself at an according collect-
ing/recycling point. By doing so, plastic and metal parts
can be separated and recycled. Information concerning
the disposal of materials and devices are available from
your local administration.
EC Declaration of Conformity
according to EU Guideline of Machines 98/37/EG
We, IKRA
GmbH, Schlesier Straße 36, D-64839 Münster / Altheim, declare under our sole responsibility that the
hedge trimmer EHT 600 PRO
, XH 600E-PRO (EHT 600 Profi ), to which this declaration relates correspond to the
relevant basic safety and health requirements of Directives
89/336/EEC (EMV-Guideline), 73/23/EEC (Low Voltage
Guideline), 89/37/EG (Guideline of Machines) and 2000/14/EC (noise directive). For the relevant implementa-
tion of the safety and health requirements mentioned in the Directives, the following standards and/or technical
specifi cation(s) have been respected: EN 55014-1, EN 55014-2, EN 50144-1, EN 50144-2-15, EN 61000-3-2:1995,
EN 61000-3-3: 1995, EN 774, EN 50366
.
measured acoustic capacity level 96 dB(A)
guaranteed acoustic capacity level 98 dB(A)
Conformity assessment method to annexe V / Directive 2000/14/EC
Münster, 20.01.2006 Gerhard Knorr, Technical Director
Maintenance of technical documentation:
Gerhard Knorr, Kärcherstraße 57, DE-64839 Münster
GB
Déclaration de Conformité pour la CE
conforme à la directive CE sur les machines 98/37/EG
Nous, ikra GmbH, Schlesier Straße 36, D-64839 Münster / Altheim, déclarons sous notre seule responsabilité
que les taille-haie EHT 600 PRO
, XH 600E-PRO (EHT 600 Profi ), faisant l’objet de la déclaration sont conformes
aux prescriptions fondamentales en matière de sécurité et de santé stipulées dans les Directives de la CEE
89/336/CEE (directive EMV) et 73/23/CEE (directive de basse tension), 98/37/EG (directive CE sur les machines)
et 2000/14/C.E. (directives en matière de bruit). Pour mettre en pratique dans les règles de l’art les prescriptions en
matière de sécurité et de santé stipulées dans les Directives de la CEE, il a été tenu compte des normes et/ou des
spécifi cations techniques suivantes: EN 55014-1, EN 55014-2, EN 50144-1, EN 50144-2-15, EN 61000-3-2:1995,
EN 61000-3-3: 1995, EN 774, EN 50366
.
Niveau sonore mesuré 96 dB (A)
Niveau sonore garanti 98 dB (A)
Procédure d’évaluation de conformité voir annexe V / directive 2000/14/CE
Münster, 20.01.2006 Gerhard Knorr, Directeur technique
La documentation technique est conservée par : Gerhard Knorr, Kärcherstraße 57, DE-64839 Münster
FR
Dichiarazione CE di Conformità
ai sensi della direttiva macchine 98/37/EG
Noi, ikra GmbH, Schlesier Straße 36, D-64839 Münster / Altheim, dichiara sotto la propria responsabilità che gli
tagliasiepi EHT 600 PRO
, XH 600E-PRO (EHT 600 Profi ), é conforme ai Requisiti Essenziali di Sicurezza e di Tutela
della Salute di cui alle Direttive CEE 89/336/CEE (direttiva EMV), 73/23/CEE (direttiva bassa tensione),
98/37/EG
(direttiva macchine) e 2000/14/CE (Direttiva sulla rumorosità) . Per la verifi ca della Conformidi cui alle Direttive
sopra menzionate, sono state conultate le seguenti norme armonizzate EN e Specifi cazioni Tecniche Nazionali: EN
55014-1, EN 55014-2, EN 50144-1, EN 50144-2-15, EN 61000-3-2:1995, EN 61000-3-3: 1995, EN 774, EN 50366
.
livello di potenza sonora misurato 96 dB (A)
livello di potenza sonora garantito 98 dB (A)
Procedura di valutazione della conformità secondo l’allegato V della direttiva 2000/14/CE
Münster, 20.01.2006 Gerhard Knorr, Direttore Técnico
Conservazione della documentazione tecnica:
Gerhard Knorr, Kärcherstraße 57, DE-64839 Münster
IT
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

Alpina EHT 600 PROXH 600E-PRO Operating Instructions Manual

Categoria
Tagliasiepi a motore
Tipo
Operating Instructions Manual