Indesit ARTXF 109 (EU) Guida utente
- Categoria
- Lavatrici
- Tipo
- Guida utente
1
GB
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 4
Cutting off the water or electricity supply
Cleaning the washing machine
Caring for your appliance door and drum
Cleaning the pump
Checking the water inlet hose
How to clean the detergent dispenser
Precautions and tips, 5
General safety
Disposal
Saving energy and respecting the environment
Description of the washing machine
and starting a wash cycle, 6-7
Control panel
Indicator lights
How to open and shut the drum
Starting a wash cycle
Wash cycles, 8
Table of wash cycles
Personalisation, 9
Setting the temperature
Setting the spin speed
Functions
Detergents and laundry, 10
Detergent dispenser drawer
Bleach cycle
Preparing the laundry
Garments requiring special care
Load balancing system
Troubleshooting, 11
Service, 12
ARTXF 109
Instructions for use
WASHING MACHINE
English,1
GB
CIS
Polski,25
PL
Magyar,37
HU
2
GB
Installation
! Keep this instruction manual in a safe place for
future reference. Should the appliance be sold,
transferred or moved, make sure the instruction
manual accompanies the washing machine to
inform the new owner as to its operation and
features.
! Read these instructions carefully: they contain
vital information on installation, use and safety.
Unpacking and levelling
Unpacking
1. Unpack the washing machine.
2. Check whether the washing machine has been
damaged during transport. If this is the case, do
not install it and contact your retailer.
3. Remove the four pro-
tective screws and the
rubber washer with the
respective spacer, si-
tuated on the rear of the
appliance (see figure).
4. Seal the gaps using the
plastic plugs provided.
5. Keep all the parts: you
will need them again if
the washing machine
needs to be moved to
another location.
Warning: should the
screws be re-used,
make sure you fasten
the shorter ones at the top.
! Packaging materials are not children’s toys.
Levelling
1. Install the washing machine on a flat sturdy
floor, without resting it up against walls, furniture
cabinets or other.
2. If the floor is not per-
fectly level, compensate
for any unevenness by
tightening or loosening
the adjustable front feet
(see figure); the angle
of inclination, measu-
red according to the
worktop, must not ex-
ceed 2°.
Levelling your appliance
correctly will provide it with stability and avoid any
vibrations, noise and shifting during operation.
If it is placed on a fitted or loose carpet, adjust
the feet in such a way as to allow enough room
for ventilation beneath the washing machine.
Putting your appliance in place and
moving it.
I f y o u r w a s h i n g
machine is equipped
with a special set of
retractable wheels
you can easy move it.
To lower the wheels
and thus move the
appliance effortlessly,
just pull the lever,
situated on the left-
hand side beneath the base. Once the appliance
is in the required position, put the lever back in
place. The washing machine is now firmly in
place (see figure).
Electric and water connections
Connecting the water inlet hose
1. Connect the supply
pipe by screwing it to
a cold water tab using
a ¾ gas threaded con-
nection (see figure).
Before performing the
connection, allow the
water to run freely until
it is perfectly clear.
2. Connect the other
end of the water inlet
hose to the washing
machine,
screwing it onto the ap-
pliance’s cold water in-
let, situated on the top
right-hand side on the
rear of the appliance
(see figure).
3. Make sure there are no kinks or bends in the
hose.
! The water pressure at the tap must be within
the values indicated in the Technical details
table (on the next page).
! If the water inlet hose is not long enough,
contact a specialist store or an authorised
serviceman.
! Never use hoses that have already been used.
3
GB
Technical details
Model
ARTXF 109
Dimensions
40 cm wide
85 cm high
60 cm deep
Capacity
from 1 to 6 kg
Electric
connections
Please refer to the technical
data plate fixed to the machine.
Water
connections
maximum pressure 1 MPa
(10 bar)
minimum pressure 0.05
MPa (0.5 bar)
drum capacity 42 litres
Spin speed
up to 1000 rpm
Test wash
cycles in
accordan-
ce with
directives
1061/2010
1015/2010
Programme
;
Cotton Standard 60°C.
Programme
;
Cotton Standard 40°C.
This appliance is compliant
with the following European
Community Directives:
- 2004/108/CE (Electroma-
gnetic Compatibility)
- 2006/95/CE (Low Voltage)
- 2002/96/CE
Connecting the drain hose
Connect the drain
hose, without bending
it, to a drainage duct
or a wall drain located
at a height between
65 and 100 cm from
the floor;
alternatively, rest it on
the side of a washba-
sin or bathtub, faste-
ning the duct sup-
plied to the tap (see
figure). The free end
of the hose should
not be underwater.
! We advise against the use of hose extensions;
if it is absolutely necessary, the extension must
have the same diameter as the original hose and
must not exceed 150 cm in length.
Electrical connections
Before plugging the appliance into the electricity
socket, make sure that:
• the socket is earthed and complies with all
applicable laws;
• the socket is able to withstand the maximum
power load of the appliance as indicated in the
Technical data table (see opposite);
• the power supply voltage falls within the va-
lues indicated in the Technical data table (see
opposite);
• the socket is compatible with the plug of the
washing machine. If this is not the case, repla-
ce the socket or the plug.
! The washing machine must not be installed
outdoors, even in covered areas. It is extremely
dangerous to leave the appliance exposed to
rain, storms and other weather conditions.
! When the washing machine has been installed,
the electricity socket must be within easy reach.
! Do not use extension cords or multiple sockets.
! The cable should not be bent or compressed.
! The power supply cable must only be replaced
by authorised technicians.
Warning! The company shall not be held respon-
sible in the event that these regulations are not
respected.
The first wash cycle
Once the appliance has been installed, and
before you use it for the first time, run a wash
cycle with detergent and no laundry, using the
wash cycle .
65 - 100 cm
4
GB
To access the pre-chamber:
1. using a screwdriver,
remove the cover pa-
nel on the lower front
part of the washing
machine (see figure);
2. unscrew the lid by
rotating it anti-clockwi-
se (see figure): a little
water may trickle out.
This is perfectly nor-
mal;
3. clean the inside tho-
roughly;
4. screw the lid back
on;
5. reposition the panel,
making sure the hooks
are securely in place
before you push it onto
the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If there
are any cracks, it should be replaced immedia-
tely: during the wash cycles, water pressure is
very strong and a cracked hose could easily
split open.
! Never use second-hand hoses.
Care and maintenance
Cutting off the water and electricity
supplies
• Turn off the water tap after every wash cycle.
This will limit wear on the hydraulic system in-
side the washing machine and help to prevent
leaks.
• Unplug the washing machine when cleaning it
and during all maintenance work.
Cleaning the washing machine
The outer parts and rubber components of the
appliance can be cleaned using a soft cloth
soaked in lukewarm soapy water. Do not use
solvents or abrasives.
Caring for the door and drum of
your appliance
• Always leave the porthole door ajar in order to
prevent unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-cleaning
pump which does not require any maintenance.
Sometimes, small items (such as coins or buttons)
may fall into the pre-chamber which protects the
pump, situated in its bottom part.
! Make sure the wash cycle has finished and
unplug the appliance.
How to clean the detergent dispenser
Fig. 1 Fig. 2
Cleaning:
Then clean the dispenser under a tap (fig. 3)
using an old toothbrush and, once the pair of
siphons inserted in the top of compartments
1 and 2 (fig. 4) have been pulled out, check
whether the same are not clogged and then
rinse them.
Reassembly:
Do not forget to rein-
sert the pair of siphons
into the special housings
and then to replace the
dispenser into its seat,
clicking it into place (fig.
4, 2 and 1).
Disassembly:
Press lightly on the
large button on the
front of the detergent
dispenser and pull it
upwards (fig. 1).
Fig. 3
Fig. 4
5
GB
Precautions and tips
! This washing machine was designed and constructed in
accordance with international safety regulations. The fol-
lowing information is provided for safety reasons and must
therefore be read carefully.
General safety
• This appliance was designed for domestic use only.
• This appliance can be used by children aged
from 8 years and above and persons with re-
duced physical, sensory or mental capabilities
or lack of experience and knowledge if they
have been given supervision or instruction
concerning use of the appliance in a safe way
and understand the hazards involved. Children
shall not play with the appliance. Cleaning
and user maintenance shall not be made by
children without supervision.
• Do not touch the machine when barefoot or with wet or
damp hands or feet.
• Do not pull on the power supply cable when unplugging
the appliance from the electricity socket. Hold the plug and
pull.
• Do not touch the drained water as it may reach extremely
high temperatures.
• Never force the porthole door. This could damage the safety
lock mechanism designed to prevent accidental opening.
• If the appliance breaks down, do not under any circum-
stances access the internal mechanisms in an attempt to
repair it yourself.
• Always keep children well away from the appliance while
it is operating.
• If the appliance has to be moved, work in a group of two
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.
• Before loading laundry into the washing machine, make
sure the drum is empty.
Disposal
• Disposing of the packaging materials: observe local regu-
lations so that the packaging may be re-used.
• The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment, requires that
old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected
separately in order to optimise the recovery and
recycling of the materials they contain and reduce
the impact on human health and the environment.
The crossed out “wheeled bin” symbol on the
product reminds you of your obligation, that when
you dispose of the appliance it must be separately
collected.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
Saving energy and respecting the envi-
ronment
Saving on detergent, water, energy and time
• To avoid wasting resources, the washing machine
should be used with a full load. A full load instead
of two half loads allows you to save up to 50% on
energy.
• The pre-wash cycle is only necessary on
extremely soiled garments. Avoiding it will save on
detergent, time, water and between 5 and 15%
energy.
• Treating stains with a stain remover or leaving
them to soak before washing will cut down the
need to wash them at high temperatures. A
programme at 60°C instead of 90°C or one at
40°C instead of 60°C will save up to 50% on
energy.
• Use the correct quantity of detergent depending
on the water hardness, how soiled the garments
are and the amount of laundry you have, to avoid
wastage and to protect the environment: despite
being biodegradable, detergents do contain
ingredients that alter the natural balance of the
environment. In addition, avoid using fabric
softener as much as possible.
• If you use your washing machine from late in the
afternoon until the early hours of the morning, you
will help reduce the electricity board’s peak load.
The “Delay Timer” option helps to organise your
wash cycles accordingly.
• If your laundry has to be dried in a tumble dryer,
select a high spin speed. Having the least water
possible in your laundry will save you time and
energy in the drying process.
6
GB
Drain
End of wash cycle
Description of the washing
machine and starting a wash cycle
TEMPERATURE
button
WASH CYCLE
PROGRESS
FUNCTION
buttons with
indicator lights
ON/OFF
button with indicator light
SPIN
SPEED
button
LID LOCKED
indicator light
START/PAUSE
button with indicator light
Control panel
WASH CYCLE
knob
DISPLAY
CONTROL PANEL LOCK
button with indicator light
ON/OFF button with indicator light: switches the machine
on and off. If the indicator light is illuminated, this indicates
that the machine is switched on.
WASH CYCLE knob: programmes the wash cycles. During
the wash cycle, the knob does not move.
SPIN SPEED button: sets the spin speed or exclude the
spin cycle completely (see “Personalisation”).
TEMPERATURE button: sets the temperature or the cold
wash cycle (see “Personalisation”).
DISPLAY: indicates the time remaining for the selected
wash cycle and, if a delayed start has been programmed,
the time remaining until the start of the wash cycle.
CONTROL PANEL LOCK button with indicator light:
activates or deactivates the control panel lock.
FUNCTION buttons with indicator light: used to select the
available functions. The indicator light corresponding to the
selected function will remain lit.
WASH CYCLE PROGRESS
indicator light
s: used to
monitor the progress of the wash cycle. The illuminated
indicator light shows which phase is in progress.
DOOR LOCKED indicator light: indicates whether the
door may be opened or not (see next page).
START/PAUSE button with indicator light: starts or tem-
porarily interrupts the wash cycles.
N.B. To pause the wash cycle in progress, press this
button; the corresponding indicator light will flash orange,
while the indicator light for the current wash cycle phase
will remain lit in a fixed manner. If the DOOR LOCKED
indicator light is switched off, the door may be opened.
To start the wash cycle from the point at which it was
Standby mode
This washing machine, in compliance with new energy saving
regulations, is fitted with an automatic standby system which
is enabled after about 30 minutes if no activity is detected.
Press the ON-OFF button briefly and wait for the machine to
start up again.interrupted, press this button again.
Consumption in off-mode: 0,5 W
Consumption in Left-on: 0,5 W
Indicator lights
The indicator lights provide important information.
This is what they can tell you:
Wash cycle phase indicator lights
As the WASH CYCLE knob is rotated, the indicator lights illuminate,
indicating the stages which will be performed by the machine in ac-
cordance with the selected wash cycle. Once the desired wash cycle
has been selected and has begun, the indicator lights switch on one
by one to indicate which phase of the cycle is currently in progress.
Function buttons and corresponding indicator lights
When a function is selected, the corresponding indicator light will
illuminate. If the selected function is not compatible with the pro-
grammed wash cycle, the corresponding indicator light will flash, a
sound signal will be emitted and the function will not be activated.
If a function which is incompatible with another function selected
previously, only the most recent selection will remain active.
Wash
Rinse
Spin
7
GB
Fig. 1
Fig. 2
Fig. 3
Fig. 4
A) Opening (Fig. 1):
Lift the external lid and open it completely.
B) Opening the drum (Soft opening):
With one finger, push the button indicated in fig. 2
and the drum will open delicately.
C) Loading the washing machine (Fig. 3).
D) Shutting (Fig. 4):
- close the drum fully by first shutting the front
door followed by the rear one;
- then ensure the hooks on the front door are
perfectly housed within the seat of the rear door;
- after the hooks have clicked into position, press
both doors lightly downwards to make sure they
do not come loose;
- finally shut the external lid.
E) Drum End Stop (Fig. 2):
Once the wash cycle has been completed, the drum will
position itself with doors facing upward for ease pf opening.
Starting a wash cycle
1. Turn the washing machine on by pressing the
ON/OFF button. All the indicator lights will turn on for a
few seconds, then only the indicator lights relative to the
selected programme settings will remain lit and the START/
PAUSE indicator light will flash.
2. Load the laundry, close the door and the lid.
3. Set the WASH CYCLE knob to the desired programme.
4. Set the washing temperature (see “Personalisation”).
5. Set the spin speed (see “Personalisation”).
6. Measure out the detergent and washing additives (see
“Detergents and laundry”).
7. Select the desired functions.
8. Start the wash cycle by pressing the START/PAUSE
button and the corresponding indicator light will remain lit
in a fixed manner, in green.
To cancel the set wash cycle, pause the machine by pres-
sing the START/PAUSE button and select a new cycle.
9. At the end of the wash cycle the indicator light will
switch on. The LID LOCKED indicator light will switch off,
indicating that the door may be opened. Take out your
laundry and leave the appliance door ajar to make sure the
drum dries completely.
Switch the washing machine off by pressing the ON/OFF
button.
Temperature indicator light
When a temperature value is selected, the cor-
responding indicator light will illuminate.
Spin indicator light
When a spin value is selected, the correspon-
ding indicator light will illuminate.
Control panel lock indicator light
To activate the control panel lock, press and hold the
button for approximately 2 seconds. When the indicator
light is illuminated, the control panel is locked. This means
it is possible to prevent wash cycles from being modified
accidentally, especially where there are children in the home.
To deactivate the control panel lock, press and hold the
button for approximately 2 seconds.
Lid locked indicator light
If this indicator light is on, the appliance door is locked to prevent it
from being opened accidentally; to avoid any damage, wait for the
indicator light to switch off (it will take about three minutes) before
you open the appliance door.
N.B. If the DELAY TIMER function is activated, the door can-
not be opened; pause the machine by pressing the START/
PAUSE button if you wish to open it.
! If the START/PAUSE indicator light (orange) flashes rapidly
at the same time as the function indicator light, this indicates
a problem has occurred (see “Troubleshooting”).
How to open and to close the drum
8
GB
Table of wash cycles
Wash cycles
Cotton Standard 20° (wash cycle 4). Ideal for heavily soiled cotton loads. The effective performance levels achieved at cold
temperatures, which are comparable to washing at 40°, are guaranteed by a mechanical action which operates at varying
speed, with repeated and frequent peaks.
Mix 30’ (wash cycle 6) this wash cycle was designed to wash lightly soiled garments quickly: it lasts just 30 minutes and the-
refore saves both energy and time. By selecting this wash cycle (6 at 30°C), it is possible to wash different fabrics together
(except for wool and silk items), with a maximum load of 3 kg.
Mix 15’(wash cycle 7) this wash cycle was designed to wash lightly soiled garments quickly: it lasts just 15 minutes and the-
refore saves both energy and time. By selecting this wash cycle (7 at 30°C), it is possible to wash different fabrics together
(except for wool and silk items), with a maximum load of 1.5 kg.
Sanitizing cycle (wash cycle 8). A high-temperature hygienic wash cycle (over 60°C) which requires the use of bleach. Pour
the bleach, the detergent and the additives into the relevant compartments (see paragraph entitled “Detergent dispenser
drawer”).
Goodnigt cycle (wash cycle 9). This is a silent cycle which can be run at night, when the electricity prices are lower. The
wash cycle is designed for cottons and synthetics. At the end of the cycle the machine stops while there is still water in the
drum; to spin and drain the laundry press the START/PAUSE button; alternatively the machine will perform the spin cycle and
drain the water automatically after 8 hours.
Baby cycle (wash cycle 10). This wash cycle can be used to remove the soiling typically caused by babies, while ensuring
that all detergent is removed from nappies in order to prevent the delicate skin of babies from suffering allergies. The cycle
has been designed to reduce the amount of bacteria by using a greater quantity of water and optimising the effect of special
disinfecting additives added to the detergent.
At the end of the wash cycle, the machine will slowly rotate the drum to prevent the formation of creases; to end the cycle
press the START/PAUSE button.
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-
ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
1) Test wash cycle in compliance with directive 1061/2010: set wash cycle with a temperature of 60°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be
washed at 60°C . The actual washing temperature may differ from the indicated value.
2) Test wash cycle in compliance with directive 1061/2010: set wash cycle with a temperature of 40°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be
washed at 40°C . The actual washing temperature may differ from the indicated value.
For all Test Institutes:
2) Long wash cycle for cottons: set wash cycle with a temperature of 40°C.
3) Long wash cycle for synthetics: set wash cycle 5 with a temperature of 40°C.
Wash cycles
Description of the wash cycle
Max.
temp.
(°C)
Max.
speed
(rpm)
Detergents
Max. load
(kg)
Residual
dampness%
Energy con-
sumptionkWh
Total water lt
Cycle dura-
tion
Prewash
Bleach
Wash
Fabric
softener
1
Cotton + Prewash: extremely soiled whites.
90° 1000
-
6 62 1,92 67 160’
Cotton Standard 60° (1): heavily soiled whites and resistant colours.
60° 1000 - -
6 62 1,04 50,0 165’
Cotton Standard 40° (2): lightly soiled resistant and delicate colours.
40° 1000 - -
6 62 1,09 92 160’
4
Cotton Standard 20°: lightly soiled resistant and delicate colours.
20° 1000 - -
6 - - - 180’
5
Synthetics: heavily soiled resistant colours.
60° 800 - -
3 44 0,85 39 110’
5
Synthetics (3): lightly soiled resistant colours.
40° 800 - -
3 44 0,53 39 100’
6
Mix 30': to refresh lightly soiled garments quickly (not suitable for
wool, silk and clothes which require washing by hand).
30° 800 - -
3 71 0,25 33 30’
7
Mix 15': to refresh lightly soiled garments quickly (not suitable for
wool, silk and clothes which require washing by hand).
30° 800 - -
1,5 71 0,08 29 15’
8
Sanitizing cycle: extremely soiled whites.
90° 1000 -
6 - - - 180’
9
Goodnigt cycle: lightly soiled delicate colours.
40° 800 - -
4 - - - 280’
10
Baby cycle: heavily soiled delicate colours.
40° 800 - -
2 - - - 120’
11
Shirts
40° 600 - -
2 - - - 80’
12
Silk/Curtains: for garments in silk and viscose, lingerie.
30° 0 - -
1 - - - 55’
13
Wool: for wool, cashmere, etc.
40° 800 - -
1 - - - 65’
Rinse
- 1000 - - -
6 - - - 36’
Spin
- 1000 - - - - 6 - - - 16’
Drain
- 0 - - - - 6 - - - 2’
9
GB
Setting the temperature
By pressing the TEMPERATURE button to set the wash temperature (see Table of wash cycles).
The temperature may be lowered, or even set to a cold wash ( ).
The washing machine will automatically prevent you from selecting a temperature which is higher than the maximum value
set for each wash cycle.
Setting the spin speed
By pressing the SPIN SPEED button to set the spin speed for the selected wash cycle.
The maximum spin speeds available for each wash cycle are as follows:
Wash cycles Maximum spin speed
Cottons 1000 rpm
Synthetics 800 rpm
Wool 800 rpm
Silk drain only
The spin speed may be lowered, or the spin cycle can be excluded altogether by selecting the symbol .
The washing machine will automatically prevent you from selecting a spin speed which is higher than the maximum speed
set for each wash cycle.
Functions
The various wash functions available with this washing machine will help to achieve the desired results, every time.
To activate the functions:
1. Press the button corresponding to the desired function;
2. the function is enabled when the corresponding indicator light is illuminated.
Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in conjunction with the
selected wash cycle.
Delay timer
To set a delayed start for the selected wash cycle, press the button repeatedly until the desired delay time is displayed (this
may be between 1 hour and 24 hours).
To disable the function press the button until the text is displayed.
N.B. Once you have pressed the START/PAUSE button, the delay time may only be decreased if you wish to modify it.
! This option is enabled with all programmes.
Super Wash
Because a greater quantity of water is used in the initial phase of the cycle, and because of the increased cycle duration, this
function offers a high-performance wash.
! This function may not be used in conjunction with wash cycles 1, 6, 7, 8, 12, 13, , .
Extra rinse
By selecting this function, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is particularly
useful for sensitive skin.
! This function may not be used in conjunction with wash cycles 6, 7, , .
Easy iron
By selecting this function, the wash and spin cycles will be modified in order to reduce the formation of creases. At the end of
the cycle the washing machine will perform slow rotations of the drum.
For the 12 wash cycle, the machine will end the cycle while the laundry is soaking, the EASY IRON and START/PAUSE indi-
cator lights will flash (orange) and the RINSE phase will remain lit in a fixed manner. To drain the water so that the laundry may
be removed, press the START/PAUSE button or the EASY IRON button.
! This function may not be used in conjunction with wash cycles 6, 7, 8, 9, 10, 13, , , .
Personalisation
10
GB
Detergents and laundry
Detergent dispenser drawer
Good washing results also depend on the correct dose of
detergent: adding too much detergent won’t necessarily
make for a more efficient wash, and may in fact cause
build up on the interior of your appliance and even pollute
the environment.
! Use powder detergent for white cotton garments, for pre-
washing, and for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
Open up the detergent
dispenser and pour in the
detergent and fabric softe-
ner, as follows.
compartment 1: Detergent for pre-wash
compartment 2: Detergent for the wash cycle
(powder or liquid)
It is recommended that you place liquid detergent directly
into the compartment using the appropriate dosing cup.
compartment 3: Additives (softener, etc.)
When pouring the softener in compartment 3, avoid exce-
eding the “max” level indicated.
The softener is added automatically into the machine
during the last wash. At the end of the wash programme,
some water will be left in compartment 3. This is used for
the inlet of denser fabric softeners into the machine, i.e.
to dilute the more concentrated softeners. Should more
than a normal amount of water remain in compartment 3,
this means the emptying device is blocked. For cleaning
instructions, see “Care and maintenance”.
compartment 4: Bleach
Bleach cycle
Bleaching may be performed in conjunction with wash
cycle 8.
Pour the bleach into compartment 4; pour the detergent
and softener into the corresponding compartments, then
select one of the abovementioned wash cycles.
This option is recommended only for very soiled cotton
garments.
Preparing the laundry
• Divide the laundry according to:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
• Empty all garment pockets and check the buttons.
• Do not exceed the listed values, which refer to the
weight of the laundry when dry: see “Table of wash
cycles”.
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g
Garments requiring special care
Shirts: use special wash cycle 11 to wash shirts in va-
rious fabrics and colours.
It guarantees maximum care is taken of the garments and
minimises the formation of creases.
Silk: use special wash cycle 12 to wash all silk garments.
We recommend the use of special detergent which has
been designed to wash delicate clothes.
Curtains: fold curtains and place them in a pillow case or
mesh bag. Use wash cycle 12.
Wool: The wool wash cycle on this Hotpoint-Ariston machine
has been tested and approved by The Woolmark Company
for washing wool garments labelled as hand washable
provided that the garments are washed according to the
instructions on the garment label and those issued by the
manufacturer of this washing machine. Hotpoint-Ariston
is the first washing machine brand to be approved by The
Woolmark Company for Apparel Care- Platinum for its wa-
shing performance and consumption of energy and water.
Load balancing system
Before every spin cycle, to avoid excessive vibrations and
to distribute the load in a uniform manner, the drum rotates
continuously at a speed which is slightly greater than the
washing rotation speed. If, after several attempts, the load is
not balanced correctly, the machine spins at a reduced spin
speed. If the load is excessively unbalanced, the washing ma-
chine performs the distribution process instead of spinning.
To encourage improved load distribution and balance, we
recommend small and large garments are mixed in the load.
11
GB
Troubleshooting
Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure
that the problem cannot be solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not
take in water (the indicator light for
the first wash cycle stage flashes
rapidly).
The washing machine continuously
takes in and drains water.
The washing machine does not
drain or spin.
The washing machine vibrates a lot
during the spin cycle.
The washing machine leaks.
The START/PAUSE indicator light
(orange) and the function indicator
lights flash rapidly.
There is too much foam.
Possible causes / Solutions:
• The appliance is not plugged into the socket fully, or is not making contact.
• There is no power in the house.
• The appliance Lid is not shut properly.
• The ON/OFF button has not been pressed.
• The START/PAUSE button has not been pressed.
• The water tap has not been opened.
• A delayed start has been set (see “Personalisation”).
• The water inlet hose is not connected to the tap.
• The hose is bent.
• The water tap has not been opened.
• There is no water supply in the house.
• The pressure is too low.
• The START/PAUSE button has not been pressed.
• The drain hose is not fitted at a height between 65 and 100 cm from the floor
(see “Installation”).
• The free end of the hose is under water (see “Installation”).
• The wall drainage system is not fitted with a breather pipe.
If the problem persists even after these checks, turn off the water tap, switch
the appliance off and contact the Assistance Service. If the dwelling is on one of
the upper floors of a building, there may be problems relating to water drainage,
causing the washing machine to fill with water and drain continuously. Special
anti-draining valves are available in shops and help to avoid this inconvenience.
• The wash cycle does not include draining: some wash cycles require the drain
phase to be started manually.
• The EASY IRON function has been activated: To complete the wash cycle,
press the START/PAUSE button (“Personalisation”).
• The drain hose is bent (see “Installation”).
• The drainage duct is clogged.
• The drum was not unlocked correctly during installation (see “Installation”).
• The washing machine is not level (see “Installation”).
• The washing machine is trapped between cabinets and walls (see “Installation”).
• The water inlet hose is not screwed on properly (see “Installation”).
• The detergent dispenser drawer is blocked (for cleaning instructions, see
“Care and maintenance”).
• The drain hose is not fixed properly (see “Installation”).
• Switch off the machine and unplug it, wait for approximately 1 minute and
then switch it back on again.
If the problem persists, contact the Technical Assistance Service.
• The detergent is not suitable for machine washing (it should display the text
“for washing machines” or “hand and machine wash”, or the like).
• Too much detergent was used.
12
GB
Service
Before calling for Assistance:
• Check whether you can solve the problem alone (see “Troubleshooting”);
• Restart the programme to check whether the problem has been solved;
• If this is not the case, contact an authorised Technical Assistance Centre using the telephone number provided on the
guarantee certificate.
! Always request the assistance of authorised technicians.
Have the following information to hand:
• the type of problem;
• the appliance model (Mod.);
• the serial number (S/N).
This information can be found on the data plate situated on the rear of the washing machine.
13
ARTXF 109
11
11
1
1
1
3
1
!
!
!
!
!
1
65 - 100 cm
!
1
3
1
1
1
1
3
1
.
3
3
!
1
ÕËÎÏÎK (программа 4) белья стандартная программа идеально подходит для стирки х/б белья со средним
загрязнением. Отличные результаты получаются также при стирке в холодной воде, сравнимые со стиркой при 40°,
обеспечиваются механическим действием с разной скоростью с повторяющимися частыми пиками.
MИKС 30’ (
программа 6
) предназначена для быстрой стирки слабозагрязненного белья цикл длится всего 30
минут, что позволяет сэкономить время и электроэнергию. По этой программе (
6
, 30°C) можно стирать вместе
белье из разных тканей (за исключением шерсти и шелка) с максимальной загрузкой 3 кг.
MИKС 15’ (
программа 7
) предназначена для быстрой стирки слабозагрязненного белья цикл длится всего 15
минут, что позволяет сэкономить время и электроэнергию. По этой программе (
7
, 30°C) можно стирать вместе
белье из разных тканей (за исключением шерсти и шелка) с максимальной загрузкой 1,5 кг.
ЦИKЛ АНТИБАKТЕРИЯ (программа
8
). Дезинфецирующая программа с высокой температурой, предусматривающая
использование отбеливателя при температуре выше 60°C.
Для отбеливания залейте отбеливатель, моющее средство
и добавки в соответствующие ячейки (см параграф «Распределитель моющих средств»).
НОЧНОЙ ЦИKЛ (программа
9
). Это бесшумный цикл, который можно включить ночью, экономя электроэнергию.
Данная программа расчитана на стирку синтетических и х/б вещей. По завершении цикла машина останавливается
с водой в барабане; для слива и отжима нажмите кнопку START/PAUSE, в противном случае по прошествии 8
часов машина автоматически произведет слив воды и отжим.
ДЕТСKОЕ БЕЛЬЕ (программа
10
). Программа удаляет типичные загрязнения детской одежды, гарантируя удаление
моющего средства из ткани во избежание аллергии чувствительной детской кожи. Данный цикл расчитан на
сокращение количества бактерий благодаря использованию большего объема воды и оптимизируя воздействие
специальных дезинфицирующих добавок старильного вещества. По завершении стирки машина продолжит
медленно вращать барабан во избежание сминания белья. Для остановки цикла нажмите кнопку START/PAUSE
1
90° 1000
-
6 160’
ÕËÎÏÎK (1): ñèëüíîçàãðÿçí¸ííîå áåëîå è ïðî÷íî
îêðàøåííîå öâåòíîå áåëü¸.
60° 1000 - -
6 165’
ÕËÎÏÎK (2):
î÷åíü ãðÿçíîå áåëîå è äåëèêàòíîå öâåòíîå áåëüå.
40° 1000 - -
6 160’
4
ÕËÎÏÎK:
î÷åíü ãðÿçíîå áåëîå è äåëèêàòíîå öâåòíîå áåëüå.
20° 1000 - -
6 180’
5
60° 800 - -
3 110’
6
3
30° 800 - -
3 30’
7
1
30° 800 - -
1,5 15’
8
90° 1000 -
6 180’
9
40° 800 - -
4 280’
10
40° 800 - -
2 120’
11
40° 600 - -
2 80’
12
30° 0 - -
1 55’
13
40° 800 - -
1 65’
- 1000 - - -
6 36’
- 1000 - - - - 6 16’
- 0 - - - - 6 2’
1
1
!
! 1, 6, 7, 8, 12, 13, , .
!
! 6, 7, 8, 9, 10, 13, , ,
1
90° 1000
-
6 160’
ÕËÎÏÎK (1): ñèëüíîçàãðÿçí¸ííîå áåëîå è ïðî÷íî
îêðàøåííîå öâåòíîå áåëü¸.
60° 1000 - -
6 165’
ÕËÎÏÎK (2):
î÷åíü ãðÿçíîå áåëîå è äåëèêàòíîå öâåòíîå áåëüå.
40° 1000 - -
6 160’
4
ÕËÎÏÎK:
î÷åíü ãðÿçíîå áåëîå è äåëèêàòíîå öâåòíîå áåëüå.
20° 1000 - -
6 180’
5
60° 800 - -
3 110’
6
3
30° 800 - -
3 30’
7
1
30° 800 - -
1,5 15’
8
90° 1000 -
6 180’
9
40° 800 - -
4 280’
10
40° 800 - -
2 120’
11
40° 600 - -
2 80’
12
30° 0 - -
1 55’
13
40° 800 - -
1 65’
- 1000 - - -
6 36’
- 1000 - - - - 6 16’
- 0 - - - - 6 2’
1
3
3
3
3
8.
• Не превышайте значения, указанные в «Таблице
программ», указывающие вес сухого белья.
11
1
1
Цикл стирки “Шерсть» данной стиральной
машины Hotpoint-Ariston прошел тестирование и был
твержден Компанией Woolmark Company для стирки
шерстяных изделий, классифицированных как «для
ручной стирки» с тем, чтобы тирка выполнялась
в соответствии с инсрукциями на этикетке вещи и
инструкциями, прилагаемым изготовителем бытового
электроприбора. Hotpoint-Ariston – это первая марка
стиральных машин, получившая от Woolmark Com-
pany сертификацию Woolmark Apparel Care - Platinum
за качество стирки и за экономный расход воды и
электроэнергии.
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
Indesit ARTXF 109 (EU) Guida utente
- Categoria
- Lavatrici
- Tipo
- Guida utente
in altre lingue
- English: Indesit ARTXF 109 (EU) User guide
- polski: Indesit ARTXF 109 (EU) instrukcja