Indesit BWE 71683 Manuale del proprietario

Categoria
Lavatrici
Tipo
Manuale del proprietario

Questo manuale è adatto anche per

1
GB
WASHING MACHINE
Instructions for use
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 4
Cutting off the water and electricity supplies
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and tips, 5
General safety
Disposal
Opening the porthole door manually
Description of the washing machine, 6-7
Control panel
Display
Running a wash cycle, 8
Wash cycles and options, 9-10
Table of wash cycles
Wash options
Push & Wash
Detergents and laundry, 11-12
Detergent dispenser drawer
Preparing the laundry
Special wash cycles
Load balancing system
Troubleshooting, 13
Service, 14
English,1
GB
BWE 71683
IT FR
DE
NL
Italiano,15
Français,29
Deutsch,43
Nederlands,57
2
GB
! This instruction manual should be kept in a safe
place for future reference. If the washing machine
is sold, transferred or moved, make sure that the
instruction manual remains with the machine so
that the new owner is able to familiarise himself/
herself with its operation and features.
! Read these instructions carefully: they contain
vital information relating to the safe installation
and operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its packaging.
2. Make sure that the washing machine has
not been damaged during the transportation
process. If it has been damaged, contact the
retailer and do not proceed any further with the
installation process.
3. Remov e t h e 4
protective screws (used
during transportation)
and the rubber washer
with the corresponding
spacer, located on
the rear part of the
appliance (see figure).
4. Close off the holes using the plastic plugs
provided.
5. Keep all the parts in a safe place: you will need
them again if the washing machine needs to be
moved to another location.
! Packaging materials should not be used as
toys for children.
Levelling
1. Install the washing machine on a flat sturdy
floor, without resting it up against walls, furniture
cabinets or anything else.
2. If the floor is not
p e r f e c t l y l e v e l ,
c o m p e n s a t e f o r
any unevenness by
tightening or loosening
the adjustable front
feet (see figure); the
angle of inclination,
measured in relation
to the worktop, must
not exceed 2°.
Levelling the machine correctly will provide
it with stability, help to avoid vibrations and
excessive noise and prevent it from shifting
while it is operating. If it is placed on carpet or
a rug, adjust the feet in such a way as to allow
a sufficient ventilation space underneath the
washing machine.
Connecting the electricity and
water supplies
Connecting the water inlet hose
1. Connect the supply
pipe by screwing it
to a cold water tap
using a ¾ gas threaded
connection (see figure).
Before performing the
connection, allow the
water to run freely until
it is perfectly clear.
2 . C o n n e c t t h e
inlet hose to the
washing machine by
screwing it onto the
corresponding water
inlet of the appliance,
which is situated on
the top right-hand side
of the rear part of the
appliance (see figure).
3. Make sure that the hose is not folded over
or bent.
! The water pressure at the tap must fall within
the values indicated in the Technical details table
(see next page).
! If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
Installation
3
GB
Connecting the drain hose
Connect the drain
hose, without bending
it, to a drainage duct or
a wall drain located at a
height between 65 and
100 cm from the floor;
alternatively, rest it on
the side of a washbasin
or bathtub, fastening
the duct supplied to
the tap (see figure).
The free end of the
hose should not be
underwater.
! We advise against the use of hose extensions;
if it is absolutely necessary, the extension must
have the same diameter as the original hose and
must not exceed 150 cm in length.
Electrical connections
Before plugging the appliance into the electricity
socket, make sure that:
•the socketisearthed and complies with all
applicable laws;
•thesocketisabletowithstandthemaximum
power load of the appliance as indicated in the
Technical data table (see opposite);
•thepowersupplyvoltagefallswithinthevalues
indicated in the Technical data table (see
opposite);
•the socket is compatible with the plug of
the washing machine. If this is not the case,
replace the socket or the plug.
! The washing machine must not be installed
outdoors, even in covered areas. It is extremely
dangerous to leave the appliance exposed to
rain, storms and other weather conditions.
! When the washing machine has been installed,
the electricity socket must be within easy reach.
! Do not use extension cords or multiple sockets.
! The cable should not be bent or compressed.
! The power supply cable must only be replaced
by authorised technicians.
Warning! The company shall not be held responsible
in the event that these regulations are not respected.
The first wash cycle
Once the appliance has been installed, and before
you use it for the first time, run a wash cycle
with detergent and no laundry, using the wash
cycle “Auto Clean” (see “Cleaning the washing
machine”).
65 - 100 cm
Technical data
Model
BWE 71683
Dimensions
width 59.5 cm
height 85 cm
depth 54 cm
Capacity
from 1 to 7 kg
Electrical
connections
please refer to the technical
data plate fixed to the ma-
chine
Water
connections
maximum pressure
1 MPa (10 bar)
minimum pressure
0.05 MPa (0.5 bar)
drum capacity 52 litres
Spin speed
up to 1600 rotations per minute
Test wash
cycles in
accordance
with re-
gulations
1061/2010
and
1015/2010
Programme 9:
Eco Cotton 60°.
Programme 9:
Eco Cotton 40°.
This appliance conforms to
the following EC Directives:
- 2004/108/EC (Electroma-
gnetic Compatibility)
- 2006/95/EC (Low Voltage)
- 2012/19/EU (WEEE)
4
GB
Care and maintenance
Cleaning the pump
The washing machine is fitted with a self-
cleaning pump which does not require any
maintenance. Sometimes, small items (such
as coins or buttons) may fall into the protective
pre-chamber at the base of the pump.
! Make sure the wash cycle has finished and
unplug the appliance.
To access the pre-chamber:
1. Take off the cover
panel on the front
of the machine by
first pressing it in
the centre and then
pushing downwards
on both sides until
you can remove it
(see figures).
2. Unscrew the lid
by rotating it anti-
clockwise (see figure):
a little water may
trickle out. This is
perfectly normal.
3. Clean the inside thoroughly.
4. Screw the lid back on.
5. Reposition the panel, making sure the hooks
are securely in place before you push it onto
the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If
there are any cracks, it should be replaced
immediately: during the wash cycles, water
pressure is very strong and a cracked hose
could easily split open.
! Never use second-hand hoses.
Cutting off the water and electricity
supplies
•Turnoffthewatertapaftereverywashcycle.
This will limit wear on the hydraulic system inside
the washing machine and help to prevent leaks.
•Unplugthewashingmachinewhencleaningit
and during all maintenance work.
Cleaning the washing machine
•Theouterpartsandrubbercomponents
of the appliance can be cleaned using a soft
cloth soaked in lukewarm soapy water. Do not
use solvents or abrasives.
•Thewashingmachinehasa“AutoClean”
programme for its internal parts that must be
run with no load in the drum.
For maximum performance you may want
to use either the detergent (i.e. a quantity
10% the quantity specified for lightly-soiled
garments) or special additives to clean the
washing machine. We recommend running a
cleaning programme every 40 wash cycles.
To start the programme press buttons A and
B simultaneously for 5 seconds (see figure).
The programme will start automatically and
will last approximately 70 minutes. To stop the
cycle press the START/PAUSE button.
Cleaning the detergent dispenser
drawer
To remove the drawer,
press lever (1) and pull
the drawer outwards
(2) (see figure).
Wash it under running
water; this procedure
should be repeated
frequently.
Caring for the door and drum of your
appliance
•Alwaysleavetheportholedoorajarinorderto
prevent unpleasant odours from forming.
2
1
1
2
3
A
B
5
GB
Precautions and tips
! This washing machine was designed and constructed
in accordance with international safety regulations. The
following information is provided for safety reasons and
must therefore be read carefully.
General safety
•Thisappliancewasdesignedfordomesticuseonly.
•Thisappliancecanbeusedbychildren
aged from 8 years and above and
persons with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given
supervision or instruction concerning use of
the appliance in a safe way and understand
the hazards involved. Children shall not
play with the appliance. Cleaning and user
maintenance shall not be made by children
without supervision.
•Thewashingmachinemustonlybeusedbyadults,in
accordance with the instructions provided in this manual.
•Donottouchthemachinewhenbarefootorwithwetor
damp hands or feet.
•Donotpullonthepowersupplycablewhenunplugging
the appliance from the electricity socket. Hold the plug
and pull.
•Donotopenthedetergentdispenserdrawerwhilethe
machine is in operation.
•Donottouchthedrainedwaterasitmayreach
extremely high temperatures.
•Neverforcetheportholedoor.Thiscoulddamagethe
safety lock mechanism designed to prevent accidental
opening.
•Iftheappliancebreaksdown,donotunderany
circumstances access the internal mechanisms in an
attempt to repair it yourself.
•Alwayskeepchildrenwellawayfromtheappliancewhile
it is operating.
•Thedoorcanbecomequitehotduringthewashcycle.
•Iftheappliancehastobemoved,workinagroupoftwo
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.
•Beforeloadinglaundryintothewashingmachine,make
sure the drum is empty.
Disposal
•Disposingofthepackagingmaterials:observelocal
regulations so that the packaging may be re-used.
• TheEuropeanDirective2012/19/EU-WEEEonWaste
Electrical and Electronic Equipment, requires that old
household electrical appliances must not be disposed
of in the normal unsorted municipal waste stream. Old
appliances must be collected separately in order to
optimise the recovery and recycling of the materials they
contain and reduce the impact on human health and the
environment. The crossed out “wheeled bin” symbol on
the product reminds you of your obligation, that when
you dispose of the appliance it must be separately
collected.
Consumers should contact their local authority or retailer
for information concerning the correct disposal of their
old appliance.
Opening the porthole door manually
In the event that it is not possible to open the porthole
door due to a powercut, and if you wish to remove the
laundry, proceed as follows:
1. remove the plug from the
electrical socket.
2. make sure the water level
inside the machine is lower
than the door opening; if
it is not, remove excess
water using the drain hose,
collecting it in a bucket as
indicated in the figure.
3. remove the cover panel
on the lower front part of
the washing machine (see
figure).
4. pull outwards using the tab as indicated in the figure,
until the plastic tie-rod is freed from its stop position; pull
downwards and open the door at the same time.
5. reposition the panel, making sure the hooks are securely
in place before you push it onto the appliance.
20
1
2
3
6
GB
Description of the washing
machine
Control panel
TEMPERATURE
button
WASH
CYCLE
SELECTOR
KNOB
Detergent dispenser drawer
ON/OFF
button
SPIN
button
START/PAUSE
button
and indicator light
DELAYED
START
button
OPTION
buttons
Detergent dispenser drawer: used to dispense
detergents and washing additives (see Detergents and
laundry”).
ON/OFF button: press this briefly to switch the machine
on or off. The START/PAUSE indicator light which flashes
slowly in a green colour shows that the machine is switched
on. To switch off the washing machine during the wash cycle,
press and hold the button for approximately 3 seconds; if
the button is pressed briefly or accidentally the machine will
not switch off.
If the machine is switched off during a wash cycle, this wash
cycle will be cancelled.
PUSH & WASH button: (see “Wash cycles and options”).
WASH CYCLE SELECTOR KNOB: used to set the desired
wash cycle (see “Table of wash cycles”).
CHILD LOCK button: to activate the control panel lock,
press and hold the button for approximately 2 seconds.
When the indicator light is illuminated, the control panel
is locked (apart from the ON/OFF button). This means it
is possible to prevent wash cycles from being modified
accidentally, especially where there are children in the home.
To deactivate the control panel lock, press and hold the button
for approximately 2 seconds.
OPTION buttons: press to select the available options.
The indicator light corresponding to the selected option will
remain lit.
TEMPERATURE
40°
60°
button: press to reduce or completely
exclude the temperature; the value appears on the display.
SPIN button: press to reduce or completely exclude the
spin cycle; the value appears on the display.
DELAYED START button: press to set a delayed start
for the selected wash cycle; the delay period appears on
the display.
START/PAUSE button and indicator light: when the
green indicator light flashes slowly, press the button to start a
wash cycle. Once the cycle has begun the indicator light will
remain lit in a fixed manner. To pause the wash cycle, press
the button again; the indicator light will flash in an amber
colour. If the symbol is not illuminated, the door may be
opened. To start the wash cycle from the point at which it
was interrupted, press the button again.
Standby mode
This washing machine, in compliance with new energy saving
regulations, is fitted with an automatic standby system which
is enabled after about 30 minutes if no activity is detected.
Press the ON-OFF button briefly and wait for the machine
to start up again.
DISPLAY
PUSH & WASH
button
CHILD LOCK
button
7
GB
The display is useful when programming the machine and provides a great deal of information.
The duration of the available wash cycles and the remaining time of a running cycle appear in section A; if the DELAYED
START option has been set, the countdown to the start of the selected wash cycle will appear.
Pressing the corresponding button allows you to view the maximum spin speed and temperature values attained by the
machine during the set wash cycle, or the values selected most recently, if these are compatible with the set wash cycle.
The hour-glass flashes while the machine processes the data on the basis of the selected programme. After a maximum of
10 minutes, the icon remains lit in a fixed manner and the final amount of time remaining is displayed. The hour-glass icon
will then switch off approximately 1 minute after the final amount of time remaining has appeared.
The “wash cycle phases” corresponding to the selected wash cycle and the “wash cycle phase” of the running wash cycle
appear in section B:
Main wash
Rinse
Spin
Drain
The “delay” symbol , when lit, indicates that the set “delayed start” value has appeared on the display.
There are three levels in section C concerning the washing options.
DOOR LOCKED indicator light:
The lit symbol indicates that the door is locked. To prevent any damage, wait until the symbol turns off before opening the
door.
To open the door while a cycle is in progress, press the START/PAUSE button; if the DOOR LOCKED symbol is switched
off the door may be opened.
Display
B
C (see “Wash options”)
A
C
8
GB
Running a wash cycle
Rapid programming
1. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed
the maximum load value indicated in the table of
programmes and wash cycles on the following page.
2. ADD THE DETERGENT. Pull out the detergent
dispenser drawer and pour the detergent into the
relevant compartments as described in “Detergents and
laundry”.
3. CLOSE THE DOOR.
4. Press the “PUSH & WASH” button to start the wash
programme.
Traditional programming
1. SWITCH THE MACHINE ON. Press the button;
the START/PAUSE indicator light will flash slowly in a
green colour.
2. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed
the maximum load value indicated in the table of
programmes and wash cycles on the following page.
3. ADD THE DETERGENT. Pull out the detergent
dispenser drawer and pour the detergent into the relevant
compartments as described inDetergents and laundry”.
4. CLOSE THE DOOR.
5. SELECT THE WASH CYCLE. Use the WASH CYCLE
SELECTOR knob to select the desired wash cycle. A
temperature and spin speed is set for each wash cycle;
these values may be adjusted. The duration of the cycle
will appear on the display.
6. CUSTOMISE THE WASH CYCLE. Use the relevant
buttons:
40°
60°
Modify the temperature and/or spin
speed. The machine automatically displays the
maximum temperature and spin speed values set for
the selected cycle, or the most recently-used settings
if they are compatible with the selected cycle. The
temperature can be decreased by pressing the
40°
60°
button, until the cold wash “OFF” setting is reached.
The spin speed may be progressively reduced by
pressing the button, until it is completely excluded
(the “OFF” setting). If these buttons are pressed again,
the maximum values are restored.
! Exception: if the 6 programme is selected, the
temperature can be increased up to a value of 60°C.
! Exception: if the 7 programme is selected, the
temperature can be increased up to a value of 60°C.
! Exception: if the 10 programme is selected, the
temperature can be increased up to a value of 90°C.
Setting a delayed start.
To set a delayed start for the selected cycle, press the
corresponding button repeatedly until the required delay
period has been reached. When this option has been
activated, the symbol lights up on the display. To
remove the delayed start setting, press the button until
the text “OFF” appears on the display.
Modify the cycle settings.
• Pressthebuttontoenabletheoption;theindicator
light corresponding to the button will switch on.
• Pressthebuttonagaintodisabletheoption;the
indicator light will switch off.
! If the selected option is not compatible with the set
wash cycle, the indicator light will flash and the option
will not be activated.
! If the selected option is not compatible with another
previously selected option, the indicator light will
flash accompanied by a buzzer (3 beeps), and only
the latter option will be activated; the indicator light
corresponding to the activated option will turn on.
! The options may affect the recommended load value
and/or the duration of the cycle.
7. START THE WASH CYCLE. Press the START/
PAUSE button. The corresponding indicator light will
turn green, remaining lit in a fixed manner, and the door
will be locked (the DOOR LOCKED symbol will be lit).
To change a wash cycle while it is in progress, pause
the washing machine using the START/PAUSE button
(the START/PAUSE indicator light will flash slowly in an
amber colour); then select the desired cycle and press
the START/PAUSE button again.
To open the door while a cycle is in progress, press
the START/PAUSE button; if the DOOR LOCKED
symbol is switched off the door may be opened. Press
the START/PAUSE button again to restart the wash
cycle from the point at which it was interrupted.
8. THE END OF THE WASH CYCLE. This will be
indicated by the text “END” on the display; when the
DOOR LOCKED symbol switches off the door may
be opened. Open the door, unload the laundry and
switch off the machine.
! If you wish to cancel a cycle which has already begun,
press and hold the button. The cycle will be stopped
and the machine will switch off.
9
GB
Wash cycles and options
Table of wash cycles
Wash options
- If the selected option is not compatible with the set wash cycle,
the indicator light will flash and the option will not be activated.
- If the selected option is not compatible with another
previously selected option, the indicator light will flash
accompanied by a buzzer (3 beeps), and only the latter
option will be activated; the indicator light corresponding
to the activated option will turn on.
Stain removal
This option allows for selecting the type of dirt so as to
optimally adjust the cycle for removing the stains. The
following types of dirt can be selected:
- Food, for stains caused by foodstuffs and beverages,
for example.
- Work, for grease and ink stains, for example.
- Outdoor, for mud and grass stains, for example.
! The wash cycle duration varies according to the type of
selected dirt.
Rapid
When this button is pressed the first time, the 45’ icon will light
up, when pressed the second time the 60’ icon lights up and
the third time the 20’ icon lights up.
1) Test wash cycle in compliance with regulations 1061/2010: set wash cycle 9 with a temperature of 60°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments
which can be washed at 60°C. The actual washing temperature may differ from the indicated value.
2) Test wash cycle in compliance with regulations 1061/2010: set wash cycle 9 with a temperature of 40°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments
which can be washed at 40°C. The actual washing temperature may differ from the indicated value.
For all Test Institutes:
3) Long wash cycle for cottons: set wash cycle 6 with a temperature of 40°C.
4) Synthetic program along: set wash cycle 7 with a temperature of 40°C.
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-
ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
* If you select programme and exclude the spin cycle, the machine will drain only.
** The duration of the wash cycle can be checked on the display.
Wash cycles
Description of the wash cycle
Max.
temp.
C)
Max.
speed
(rpm)
Detergents
Max. load (kg)
Residual
dampness %
Energy
consumption kWh
Total water lt
Cycle duration
Wash
Fabric
softener
Everyday 30° ECO
1
Daily cotton
30° 1200
3.5 - - - **
2
Daily synthetics
30° 1000
3.5 - - - **
3
Coloureds
30° 1000
3.5 - - - **
4
Delicates
30° 0
1 - - - **
5
Rapid 30min: to refresh lightly soiled garments quickly (not suitable for wool,
silk and clothes which require washing by hand).
30° 800
3.5 70 0.16 33 30’
Traditionals
6
Cotton (3): lightly soiled whites and delicate colours.
40°
(Max.60°)
1600
7 44 0.98 75 215’
7
Synthetics (4): lightly soiled resistant colours.
40°
(Max.60°)
1000
3.5 46 0.68 55 120’
8
Mixed
40° 1600
7 - - - **
9
Eco cotton 60°C (1): heavily soiled whites and resistant colours.
60° 1600
7 44 0.95 52.5 170’
9
Eco cotton 40°C (2): lightly soiled whites and delicate colours.
40° 1600
7 44 0.93 85 150’
10
White cotton: heavily soiled whites and resistant colours.
60°
(Max.90°)
1600
7 - - - **
Specials
11
Rapid
20° 800
1.5 - - - 20’
11
Rapid
40° 1200
3.5 - - - 45’
11
Rapid
60° 1000
7 - - - 60’
12
Duvet: for down-stuffed garments. 30° 1000
2 - - - **
13
Wool: for wool, cashmere, etc. 40° 800
1.5 - - - **
14
Anti odour
40° 1000
3 - - - **
Rinse + Spin - 1600 -
7 - - - **
Spin + Drain - 1600 - - 7 - - - **
Drain only * - OFF - - 7 - - - **
10
GB
Push & Wash
This function allows for starting a wash cycle even when the machine is switched off without having to press the ON/OFF
button in advance, or after switching on the machine, without having activated any button and/or selector (otherwise, the
Push & Wash function will be deactivated). To start the Push & Wash cycle press and hold the relative button for 2 seconds.
The lit indicator light indicates that the cycle has started. This wash cycle is ideal for cotton or synthetic fabrics, as it washes
at a temperature of 30° and a maximum spin speed of 1000 rpm. Maximum load 3.5 kg. (Cycle duration 45’).
How does it work?
1. Load the laundry (cotton and/or synthetic garments) and close the door.
2. Pour the detergent and additives.
3. Start the programme by pressing and holding the Push & Wash button for 2 seconds. The relative indicator light turns
green and the door will lock (the DOOR LOCKED symbol turns on).
N.B.: starting the wash cycle through the Push & Wash button activates an automatic non-customisable cycle
recommended for cotton and synthetic fabrics. This programme does not allow for setting any additional options.
To open the door while an automatic cycle is under way, press the START/PAUSE button; if the DOOR LOCKED symbol
is switched off the door may be opened. Press the START/PAUSE button again to restart the wash cycle from the point at
which it was interrupted.
4. Once the programme is finished, the END indicator light turns on.
11
GB
Detergents and laundry
Detergent dispenser drawer
Successful washing results also depend on the correct dose
of detergent: adding too much detergent will not necessarily
result in a more efficient wash, and may in fact cause
build up on the inside of your appliance and contribute to
environmental pollution.
! Do not use hand washing detergents because these create
too much foam.
! Use powder detergent for white cotton garments, for pre-
washing, and for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
Open the detergent dispenser
drawer and pour in the
detergent or washing additive,
as follows.
Compartment 1: Do not pour detergent into the middle
compartment 1.
Compartment 2: Washing detergent (powder or liquid)
If liquid detergent is used, it is recommended that the
removable plastic partition A (supplied) be used for proper
dosage. If powder detergent is used, place the partition into
slot B.
Compartment 3: Additives (fabric softeners, etc.)
The fabric softener must not exceed the “max” level indicated
on the central pin.
Preparing the laundry
• Dividethelaundryaccordingto:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
• Emptyallgarmentpocketsandcheckthebuttons.
• Do not exceed thevalues listed in the “Table of wash
cycles”, which refer to the weight of the laundry when dry.
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1.200 g
1 towel 150-250 g
Special wash cycles
Daily cotton: a 30°C cycle for cotton garments. It allows
for reducing consumption of energy for heating the water,
while guaranteeing excellent results. Suitable for lightly soiled
garments.
Daily synthetics: a 30°C cycle for synthetic garments. It
allows for reducing consumption of energy for heating the
water, while guaranteeing excellent results. Suitable for lightly
soiled garments.
Coloureds: a 30°C cycle that helps to preserve the colours;
suitable for coloured cotton and synthetic garments. It allows
for reducing consumption of energy for heating the water,
while guaranteeing excellent results. Suitable for lightly soiled
garments.
Delicates: use programme 4 to wash very delicate
garments. It is advisable to turn the garments inside out
before washing them. For best results, use liquid detergent
on delicate garments.
Mixed: a 4C cycle for washing cotton and synthetic
garments together. Suitable for lightly soiled underwear.
Rapid (programme 11) allows for varying the garment
treatment duration from 20’ to 60’.
- 20’: the wash cycle that refreshes your garments in a mere
20 minutes.
- 45’: a short cycle designed for washing cotton/synthetic
blend fabrics.
- 60’: The “60’” cycle is designed to wash moderately soiled
resistant cotton garments at 6 in an hour, with good
washing performance. For synthetic or mixed garments, we
recommend lowering the temperature down to 40°.
Duvet: to wash single duvets (the weight of which should
not exceed 2 kg), cushions or clothes padded with goose
down such as puffa jackets, use the special wash programme
number 12. We recommend that duvets are placed in the drum
with their edges folded inwards (see figure) and that no more
than ¾ of the total volume of the drum is used. To achieve the
best results, we recommend that a liquid detergent is used
and placed inside the detergent dispenser drawer.
Wool - Woolmark Apparel Care - Blue:
the wool wash cycle of this machine has been approved by
The Woolmark Company for the washing of wool garments
labelled as hand wash provided that the products are
washed according to the instructions on the garment label
and those issued by the manufacturer of this washing
machine. (M1126)
In UK, Eire, Hong Kong and India the Woolmark trade mark
is a Certification trade mark.
Anti odour: use programme 14 (Synthetics) for washing
garments with bad odours (e.g. smoke, sweat, fried food).
The programme is designed to remove bad odours while
preserving the fabric fibres.
12
GB
Load balancing system
Before every spin cycle, to avoid excessive vibrations
before every spin and to distribute the load in a uniform
manner, the drum rotates continuously at a speed which
is slightly greater than the washing rotation speed. If,
after several attempts, the load is not balanced correctly,
the machine spins at a reduced spin speed. If the load is
excessively unbalanced, the washing machine performs
the distribution process instead of spinning. To encourage
improved load distribution and balance, we recommend
small and large garments are mixed in the load.
13
GB
Troubleshooting
Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Service (see “ Service”),
make sure that the problem cannot be solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not fill
with water (the text “H2O” on the
display).
The washing machine
continuously takes in and drains
water.
The washing machine does not
drain or spin.
The washing machine vibrates a
lot during the spin cycle.
The washing machine leaks.
Theoption and START/PAUSE
indicator lights flash rapidly and an
error code appears on the display
(e.g.: F-01, F-..).
There is too much foam.
Push & Wash does not activate.
Possible causes / Solutions:
•Theapplianceisnotpluggedintothesocketfully,ornotenoughtomakecontact.
•Thereisnopowerinthehouse.
•Thewashingmachinedoorisnotclosedproperly.
•TheON/OFFbuttonhasnotbeenpressed.
•TheSTART/PAUSEbuttonhasnotbeenpressed.
•Thewatertaphasnotbeenopened.
•Adelayedstarthasbeenset.
•Thewaterinlethoseisnotconnectedtothetap.
•Thehoseisbent.
•Thewatertaphasnotbeenopened.
•Thereisnowatersupplyinthehouse.
•Thepressureistoolow.
•TheSTART/PAUSEbuttonhasnotbeenpressed.
•Thedrainhoseisnotfittedataheightbetween65and100cmfromthefloor
(see “Installation”).
•Thefreeendofthehoseisunderwater(see “Installation”).
•Thewalldrainagesystemisnotfittedwithabreatherpipe.
If the problem persists even after these checks, turn off the water tap, switch the
appliance off and contact the Technical Assistance Service. If the dwelling is on one
of the upper floors of a building, there may be problems relating to water drainage,
causing the washing machine to fill with water and drain continuously. Special anti-
draining valves are available in shops and help to prevent this inconvenience.
•Thewashcycledoesnotincludedraining:somecyclesrequirethedraining
process to be enabled manually.
•Thedrainhoseisbent(see “Installation”).
•Thedrainageductisclogged.
•Thedrumwasnotunlockedcorrectlyduringinstallation(see “Installation”).
•Thewashingmachineisnotlevel(see “Installation”).
•Thewashingmachineistrappedbetweencabinetsandwalls(see “Installation”).
•Thewaterinlethoseisnotscrewedonproperly(see “Installation”).
•Thedetergentdispenserdrawerisblocked(forcleaninginstructions,see “Care
and maintenance”).
•Thedrainhoseisnotfixedproperly(see “Installation”).
•Switchoffthemachineandunplugit,waitforapproximately1minuteandthen
switch it back on again.
If the problem persists, contact the Technical Assistance Service.
•Thedetergentisnotsuitableformachinewashing(itshoulddisplaythetext“for
washing machines” or “hand and machine wash”, or the like).
•Toomuchdetergentwasused.
• AfterswitchingonthemachineacontrolotherthanPush&Washwasactivated.
Switch the machine off and press the Push & Wash button.
14
GB
Service
Before contacting the Technical Assistance Service:
• Checkwhetheryoucansolvetheproblemalone(see“Troubleshooting”).
• Restartthewashcycletocheckwhethertheproblemhasbeensolved.
• Ifthisisnotthecase,contactanauthorisedTechnicalAssistanceCentre.
! Always request the assistance of authorised technicians.
Have the following information to hand:
• thetypeofproblem;
• theappliancemodel(Mod.);
• theserialnumber(S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the
front of the appliance by opening the door.
15
IT
Sommario
Installazione, 16-17
Disimballo e livellamento
Collegamenti idraulici ed elettrici
Primo ciclo di lavaggio
Dati tecnici
Manutenzione e cura, 18
Escludere acqua e corrente elettrica
Pulire la lavabiancheria
Pulire il cassetto dei detersivi
Curare oblò e cestello
Pulire la pompa
Controllare il tubo di alimentazione dell’acqua
Precauzioni e consigli, 19
Sicurezza generale
Smaltimento
Apertura manuale della porta oblò
Descrizione della lavabiancheria, 20-21
Pannello di controllo
Display
Come effettuare un ciclo di lavaggio, 22
Programmi e opzioni, 23-24
Tabella dei programmi
Opzioni di lavaggio
Push & Wash
Detersivi e biancheria, 25-26
Cassetto dei detersivi
Preparare la biancheria
Programmi particolari
Sistema bilanciamento del carico
Anomalie e rimedi, 27
Assistenza, 28
Assistenza Attiva 7 giorni su 7
LAVABIANCHERIA
BWE 71683
Istruzioni per l’uso
Italiano
IT
16
IT
! È importante conservare questo libretto per
poterlo consultare in ogni momento. In caso di
vendita, di cessione o di trasloco, assicurarsi
che resti insieme alla lavabiancheria per infor-
mare il nuovo proprietario sul funzionamento e
sui relativi avvertimenti.
! Leggere attentamente le istruzioni: ci sono
importanti informazioni sull’installazione,
sull’uso
e sulla sicurezza.
Disimballo e livellamento
Disimballo
1. Disimballare la lavabiancheria.
2. Controllare che la lavabiancheria non abbia
subìto danni nel trasporto. Se fosse danneggia-
ta non collegarla e contattare il rivenditore.
3. Rimuovere le 4 viti
di protezione per il
trasporto e il gommino
con il relativo distan-
ziale, posti nella parte
posteriore (vedi figura).
4. Chiudere i fori con i tappi di plastica in dota-
zione.
5. Conservare tutti i pezzi: qualora la lavabian-
cheria debba essere trasportata, dovranno
essere
rimontati.
! Gli imballaggi non sono giocattoli per bambini.
Livellamento
1. Installare la lavabiancheria su un pavimento
piano e rigido, senza appoggiarla a muri, mobili
o altro.
2. Se il pavimento non
fosse perfettamente
orizzontale, compen-
sare le irregolarità
svitando o avvitando
i piedini anteriori (vedi
figura); l’angolo di
inclinazione, misurato
sul piano di lavoro, non
deve superare i 2°.
Un accurato livellamento dà stabilità alla
macchina ed evita vibrazioni, rumori e spo-
stamenti durante il funzionamento. In caso di
moquette o di un tappeto, regolare i piedini in
modo da conservare sotto la lavabiancheria
uno spazio sufficiente per la ventilazione.
Collegamenti idraulici ed elettrici
Collegamento del tubo di
alimentazione dell’acqua
1. Collegare il tubo
di alimentazione av-
vitandolo a un rubi-
netto d’acqua fredda
con bocca filettata
da 3/4 gas (vedi
figura).
Prima di allacciare,
far scorrere l’acqua
finché non sia limpi-
da.
2. Collegare il tubo
di alimentazione alla
lavabiancheria
avvitandolo all’appo-
sita presa d’acqua,
nella parte posteriore
in alto a destra (vedi
figura).
3. Fare attenzione che nel tubo non ci siano
né pieghe né strozzature.
! La pressione idrica del rubinetto deve esse-
re compresa nei valori della tabella Dati tecni-
ci (vedi pagina a fianco).
! Se la lunghezza del tubo di alimentazione
non fosse sufficiente, rivolgersi a un negozio
specializzato o a un tecnico autorizzato.
! Non utilizzare mai tubi già usati.
! Utilizzare quelli in dotazione alla macchina.
Installazione
17
IT
Collegamento del tubo di scarico
Collegare il tubo di
scarico, senza pie-
garlo, a una condut-
tura di scarico o a
uno scarico a muro
posti tra 65 e 100
cm da terra;
oppure appoggiarlo
al bordo di un lavan-
dino o di una vasca,
legando la guida in
dotazione al
rubinetto (vedi figu-
ra). L’estremità libera
del tubo di scarico
non deve rimanere
immersa nell’acqua.
! È sconsigliato usare tubi di prolunga; se in-
dispensabile, la prolunga deve avere lo stes-
so diametro del tubo originale e non superare
i 150 cm.
Collegamento elettrico
Prima di inserire la spina nella presa della
corrente, accertarsi che:
• la presa abbia la messa a terra e sia a nor-
ma di legge;
• la presa sia in grado di sopportare il carico
massimo di potenza della macchina, indi-
cato nella tabella Dati tecnici (vedi a fianco);
la tensione di alimentazione sia compresa nei
valori indicati nella tabella Dati tecnici (vedi a
fianco);
• la presa sia compatibile con la spina della
lavabiancheria. In caso contrario sostituire
la presa o la spina.
! La lavabiancheria non va installata all’aperto,
nemmeno se lo spazio è riparato, perché è
molto pericoloso lasciarla esposta a pioggia e
temporali.
! A lavabiancheria installata, la presa della
corrente deve essere facilmente raggiungibile.
! Non usare prolunghe e multiple.
! Il cavo non deve subire piegature o com-
pressioni.
! Il cavo di alimentazione deve essere sostitu-
ito solo da tecnici autorizzati.
Attenzione! L’azienda declina ogni responsabi-
lità qualora queste norme non vengano rispet-
tate.
Primo ciclo di lavaggio
Dopo l’installazione, prima dell’uso, effettuare
un ciclo di lavaggio con detersivo e senza bian-
cheria impostando il programma “Auto Pulizia”
(vedi “Pulire la lavabiancheria”).
Dati tecnici
Modello
BWE 71683
Dimensioni
larghezza cm 59,5
altezza cm 85
profondità cm 54
Capacità
da 1 a 7 kg
Collega-
menti elet-
trici
Vedi targhetta caratteristi-
che tecniche applicata sulla
macchina
Collega-
menti idrici
pressione massima
1 MPa (10 bar)
pressione minima
0,05 MPa (0,5 bar)
capacità del cesto 52 litri
Velocità di
centrifuga
sino a 1600 giri al minuto
Programmi
di
controllo
secondo i
regolamenti
1061/2010 e
1015/2010
Programma 9;
Eco Cotone 60°C.
Programma 9;
Eco Cotone 40°C.
Questa apparecchiatura è
conforme alle seguenti Diret-
tive Comunitarie:
- 2004/108/CE (Compatibili-
tà Elettromagnetica)
- 2006/95/CE (Bassa Tensione)
- 2012/19/EU (WEEE)
18
IT
Pulire la pompa
La lavabiancheria è dotata di una pompa
autopulente che non ha bisogno di manuten-
zione. Può però succedere che piccoli oggetti
(monete, bottoni) cadano nella precamera che
protegge la pompa, situata nella parte inferiore
di essa.
! Assicurarsi che il ciclo di lavaggio sia terminato
e staccare la spina.
Per accedere alla precamera:
1. rimuovere il pan-
nello di copertura sul
lato anteriore della
macchina premendo
verso il centro, quin-
di spingere verso il
basso da entrambe
i lati ed estrarlo (vedi
figure).
2. svitare il coperchio
ruotandolo in senso
antiorario (vedi figura):
è normale che fuorie-
sca un po’ d’acqua;
3. pulire accuratamente l’interno;
4. riavvitare il coperchio;
5. rimontare il pannello assicurandosi, prima di
spingerlo verso la macchina, di aver inserito i
ganci nelle apposite asole.
Controllare il tubo di alimentazio-
ne dell’acqua
Controllare il tubo di alimentazione almeno
una volta all’anno. Se presenta screpolature e
fessure va sostituito: durante i lavaggi le forti
pressioni potrebbero provocare improvvise
spaccature.
! Non utilizzare mai tubi già usati.
Manutenzione e cura
Escludere acqua e corrente elettrica
Chiudere il rubinetto dell’acqua dopo ogni lavaggio.
Si limita così lusura dellimpianto idraulico della
lavabiancheria e si elimina il pericolo di perdite.
Staccare la spina della corrente quando si
pulisce la lavabiancheria e durante i lavori di
manutenzione.
Pulire la lavabiancheria
La parte esterna e le parti in gomma possono
essere puliti con un panno imbevuto di acqua
tiepida e sapone. Non usare solventi o abrasivi.
• La lavabiancheria è dotata di un programma
di “Auto Pulizia” delle parti interne che deve
essere effettuato senza alcun tipo di carico
nel cesto.
Il detersivo (nella quantità pari al 10% di quella
consigliata per capi poco sporchi) o additi-
vi specifici per la pulizia della lavabiancheria,
potranno essere utilizzati come coadiuvanti nel
programma di lavaggio. Si consiglia di effettuare
il programma di pulizia ogni 40 cicli di lavaggio.
Per attivare il programma premere contempora-
neamente i tasti A e B per 5 sec. (vedi figura).
Il programma parti automaticamente ed av
una durata di circa 70 minuti. Per fermare il ciclo
premere il tasto START/PAUSE.
Pulire il cassetto dei detersivi
Per estrarre il cassetto
premere la leva (1) e tirarlo
verso l’esterno (2) (vedi
figura).
Lavarlo sotto lacqua
corrente; questa pulizia
va effettuata
frequentemente.
Curare oblò e cestello
Lasciare sempre socchiuso l’oblò per evitare
che si formino cattivi odori.
1
2
3
2
1
A
B
19
IT
Apertura manuale della porta oblò
Nel caso non sia possibile aprire la porta oblò a causa della
mancanza di energia elettrica e volete stendere il bucato,
procedere come segue:
1. togliere la spina dalla presa
di corrente.
2. verificate che il livello
dell’acqua all’interno della
macchina sia inferiore rispetto
all’apertura dell’oblò; in caso
contrario togliere l’acqua in
eccedenza attraverso il tubo
di scarico raccogliendola in
un secchio come indicato in
figura.
3. rimuovere il pannello di
copertura sul lato anteriore
della lavabiancheria (vedi
figura).
4. utilizzando la linguetta indicata in figura tirare verso
l’esterno fino a liberare il tirante in plastica dal fermo; tirarlo
successivamente verso il basso e contemporaneamente
aprire la porta.
5. rimontare il pannello assicurandosi, prima di spingerlo
verso la macchina, di aver inserito i ganci nelle apposite asole.
Precauzioni e consigli
! La lavabiancheria è stata progettata e costruita in
conformità alle norme internazionali di sicurezza. Queste
avvertenze sono fornite per ragioni di sicurezza e devono
essere lette attentamente.
Sicurezza generale
Questo apparecchio è stato concepito esclusivamente
per un uso di tipo domestico.
•Questo apparecchio può essere usato da
bambini da 8 anni in su e da persone con
capacità fisiche, sensoriali o mentali ridotte
o con esperienza e conoscenze insufficienti
se sono supervisionati o se hanno ricevu-
to adeguata formazione in merito all’uso
dell’apparecchio in modo sicuro e capendo
i pericoli connessi. I bambini non devono
giocare con l’apparecchio. Manutenzione
e pulizia non devono essere effettuati dai
bambini senza supervisione.
Non toccare la macchina a piedi nudi o con le mani o i
piedi bagnati o umidi.
Non staccare la spina dalla presa della corrente tirando
il cavo, bensì afferrando la spina.
Non aprire il cassetto dei detersivi mentre la macchina
è in funzione.
Non toccare l’acqua di scarico, che può raggiungere
temperature elevate.
Non forzare in nessun caso l’oblò: potrebbe danneg-
giarsi il meccanismo di sicurezza che protegge da
aperture accidentali.
In caso di guasto, in nessun caso accedere ai mecca-
nismi interni per tentare una riparazione.
Controllare sempre che i bambini non si avvicinino alla
macchina in funzione.
Durante il lavaggio l’oblò tende a scaldarsi.
Se dev’essere spostata, lavorare in due o tre persone
con la massima attenzione. Mai da soli perché la mac-
china è molto pesante.
Prima di introdurre la biancheria controlla che il cestello
sia vuoto.
Smaltimento
•Smaltimento del materiale di imballaggio:
attenersi alle norme locali, così gli imballaggi potranno
essere riutilizzati.
La direttiva Europea 2012/19/EU (WEEE) sui rifiuti di
apparecchia¬ture elettriche ed elettroniche (RAEE),
prevede che gli elettrodo¬mestici non debbano essere
smaltiti nel normale flusso dei rifiuti solidi urbani. Gli
apparecchi dismessi devono essere raccolti separata-
mente per ottimizzare il tasso di recupero e riciclaggio
dei materiali che li compongono ed impedire potenziali
danni per la salute e l’ambiente. Il simbolo del cestino
barrato è riportato su tutti i prodotti per ricordare gli
obblighi di raccolta separata. Quando si acquista una
nuova apparecchiatura equivalente si può consegnare
il RAEE al negoziante, che è tenuto a ritirarlo gratuita-
mente; i RAEE di “piccolissime dimensioni” (nessun lato
20
1
2
3
sopra i 25 cm) possono essere consegnati gratuitamen-
te ai negozianti anche se non si acquista nulla (solo nei
negozi con superficie di vendita superiore a 400 mq). Per
ulteriori informazioni sulla corretta dismissione degli elettro-
domestici i detentori potranno rivolgersi al servizio pubblico
preposto o ai rivenditori.
20
IT
Pannello di controllo
Descrizione della lavabiancheria
Tasto
TEMPERATURA
MANOPOLA
PROGRAMMI
Cassetto dei detersivi
Tasto
ON/OFF
Tasto
CENTRIFUGA
Cassetto dei detersivi: per caricare detersivi e additivi (vedi
“Detersivi e biancheria”).
Tasto ON/OFF : premere brevemente il tasto per accen-
dere o spegnere la macchina. La spia START/PAUSE che
lampeggia lentamente di colore verde indica che la macchina
è accesa. Per spegnere la lavabiancheria durante il lavaggio è
necessario tenere premuto il tasto più a lungo, circa 3 sec.; una
pressione breve o accidentale non permetterà lo spegnimento
della macchina. Lo spegnimento della macchina durante un
lavaggio in corso annulla il lavaggio stesso.
Tasto PUSH & WASH: (vedi “Programmi e opzioni”).
MANOPOLA PROGRAMMI: per impostare il programma
desiderato (vedi “Tabella dei programmi”).
Tasto BLOCCO TASTI: per attivare il blocco del pannello di
controllo, tenere premuto il tasto per circa 2 secondi. Il simbolo
acceso indica che il pannello di controllo è bloccato.
In questo modo si impediscono modifiche accidentali dei
programmi (ad eccezione del tasto ON/OFF), soprattutto se in
casa ci sono dei bambini. Per disattivare il blocco del pannello
di controllo, tenere premuto il tasto per circa 2 secondi.
Tasti OPZIONE: per selezionare le opzioni disponibili. La spia
relativa all’opzione selezionata rimarrà accesa.
Tasto TEMPERATURA
40°
60°
: premere per ridurre o esclu-
dere la temperatura; il valore viene indicato nel display.
Tasto CENTRIFUGA : premere per ridurre o escludere
del tutto la centrifuga; il valore viene indicato nel display.
Tasto PARTENZA RITARDATA : premere per imposta-
re una partenza ritardata del programma prescelto; il ritardo
viene indicato nel display.
Tasto e spia START/PAUSE : quando la spia verde lam-
peggia lentamente, premere il tasto per avviare un lavaggio.
A ciclo avviato la spia diventa fissa. Per mettere in pausa il
lavaggio, premere nuovamente il tasto; la spia lampeggerà
con colore ambra. Se il simbolo non è illuminato, si potrà
aprire l’oblò. Per far ripartire il lavaggio dal punto in cui è
stato interrotto, premere nuovamente i tasto.
Modalità stand by
Questa lavatrice, in conformità alle nuove normative
legate al risparmio energetico, è dotata di un sistema di
autospegnimento (stand by) che entra in funzione dopo circa
30 minuti nel caso di non utilizzo. Premere brevemente il
tasto ON-OFF e attendere che la macchina si riattivi.
Tasto e spia
START/PAUSE
DISPLAY
Tasto
PARTENZA
RITARDATA
Tasti
OPZIONE
Tasto
PUSH & WASH
Tasto
BLOCCO
TASTI
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70

Indesit BWE 71683 Manuale del proprietario

Categoria
Lavatrici
Tipo
Manuale del proprietario
Questo manuale è adatto anche per