ASROCK K8NF6P-VSTA Manuale del proprietario

11

1

ASRock K8NF6P-VSTA Motherboard

EnglishEnglish

English

Copyright Notice:Copyright Notice:

Copyright Notice:

No part of this installation guide may be reproduced, transcribed, transmitted, or trans-

lated in any language, in any form or by any means, except duplication of documen-

tation by the purchaser for backup purpose, without written consent of ASRock Inc.

Products and corporate names appearing in this guide may or may not be registered

trademarks or copyrights of their respective companies, and are used only for identifica-

tion or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:Disclaimer:

Disclaimer:

Specifications and information contained in this guide are furnished for informational

use only and subject to change without notice, and should not be constructed as a

commitment by ASRock. ASRock assumes no responsibility for any errors or omissions

that may appear in this guide.

With respect to the contents of this guide, ASRock does not provide warranty of any kind,

either expressed or implied, including but not limited to the implied warranties or

conditions of merchantability or fitness for a particular purpose. In no event shall

ASRock, its directors, officers, employees, or agents be liable for any indirect, special,

incidental, or consequential damages (including damages for loss of profits, loss of

business, loss of data, interruption of business and the like), even if ASRock has been

advised of the possibility of such damages arising from any defect or error in the guide

or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

Published February 2007

CALIFORNIA, USA ONLY

The Lithium battery adopted on this motherboard contains Perchlorate, a toxic

substance controlled in Perchlorate Best Management Practices (BMP) regulations

passed by the California Legislature. When you discard the Lithium battery in

California, USA, please follow the related regulations in advance.

“Perchlorate Material-special handling may apply, see

www.dtsc.ca.gov/hazardouswaste/perchlorate”

ASRock Website: http://www.asrock.com

22

2

ASRock K8NF6P-VSTA Motherboard

EnglishEnglish

English

Motherboard LMotherboard L

Motherboard L

ayoutayout

ayout

1 PS2_USB_PW1 Jumper 17 Infrared Module Header (IR1)

2 CPU Fan Connector (CPU_FAN1) 18 Floppy Connector (FLOPPY1)

3 184-pin DDR DIMM Slots (DDR1- 2) 19 Clear CMOS Jumper (CLRCMOS1)

4 Primary IDE Connector (IDE1, Blue) 20 Game Port Header (GAME1)

5 Primary SATAII Connector (SATAII_1, Red) 21 Flash Memory

6 Secondary SATAII Connector (SATAII_2, Red) 22 HDMR Slot (HDMR1)

7 Third SATAII Connector (SATAII_3, Red) 23 Front Panel Audio Header (HD_AUDIO1)

8 Fourth SATAII Connector (SATAII_4, Red) 24 PCI Express x1 Slot (PCIE2)

9 NVIDIA Single Chip 25 PCI Slots (PCI1- 2)

10 ATX 12V Power Connector (ATX12V1) 26 PCI Express x16 Slot (PCIE1)

11 USB 2.0 Header (USB6_7, Blue) 27 Internal Audio Connector: CD1 (Black)

12 USB 2.0 Header (USB8_9, Blue) 28 ATX Power Connector (ATXPWR1)

13 USB 2.0 Header (USB4_5, Blue) 29 Serial Port Connector (COM1)

14 Chassis Fan Connector (CHA_FAN1) 30 754-Pin CPU Socket

15 System Panel Header (PANEL1) 31 CPU Heatsink Retention Module

16 Chassis Speaker Header (SPEAKER 1)

33

3

ASRock K8NF6P-VSTA Motherboard

EnglishEnglish

English

HD 8CH I/OHD 8CH I/O

HD 8CH I/O

1 Parallel Port 8 Microphone (Pink)

2 RJ-45 Port 9 USB 2.0 Ports (USB01)

3 Side Speaker (Gray) 10 USB 2.0 Ports (USB23)

4 Rear Speaker (Black) 11 VGA Port

5 Central / Bass (Orange) 12 PS/2 Keyboard Port (Purple)

6 Line In (Light Blue) 13 PS/2 Mouse Port (Green)

*7 Front Speaker (Lime)

* If you use 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”. See

the table below for connection details in accordance with the type of speaker you use.

TABLE for Audio Output Connection

Audio Output Channels Front Speaker Rear Speaker Central / Bass Side Speaker

(No. 7) (No. 4) (No. 5) (No. 3)

2 V -- -- --

4VV----

6 VVV--

8 VVVV

44

4

ASRock K8NF6P-VSTA Motherboard

1.1.

1.

IntroductionIntroduction

Introduction

Thank you for purchasing ASRock K8NF6P-VSTA motherboard, a reliable motherboard

produced under ASRock’s consistently stringent quality control. It delivers excellent

performance with robust design conforming to ASRock’s commitment to quality and

endurance.

This Quick Installation Guide contains introduction of the motherboard and step-by-

step installation guide. More detailed information of the motherboard can be found in

the user manual presented in the Support CD.

Because the motherboard specifications and the BIOS software might

be updated, the content of this manual will be subject to change without

notice. In case any modifications of this manual occur, the updated

version will be available on ASRock website without further notice. You

may find the latest VGA cards and CPU support lists on ASRock

website as well.

ASRock website http://www.asrock.com

1.11.1

1.1

Package ContentsPackage Contents

Package Contents

1 x ASRock K8NF6P-VSTA Motherboard

(Micro ATX Form Factor: 9.6-in x 8.2-in, 24.4 cm x 20.8 cm)

1 x ASRock K8NF6P-VSTA Quick Installation Guide

1 x ASRock K8NF6P-VSTA Support CD

1 x Ultra ATA 66/100/133 IDE Ribbon Cable (80-conductor)

1 x 3.5-in Floppy Drive Ribbon Cable

1 x Serial ATA (SATA) Data Cable (Optional)

1 x Serial ATA (SATA) HDD Power Cable (Optional)

1 x HD 8CH I/O Shield

1 x COM Port Bracket

EnglishEnglish

English

55

5

ASRock K8NF6P-VSTA Motherboard

EnglishEnglish

English

1.21.2

1.2

SpecificationsSpecifications

Specifications

Platform - Micro ATX Form Factor: 9.6-in x 8.2-in, 24.4 cm x 20.8 cm

CPU - Socket 754 for AMD Athlon

TM

64 and Sempron processors

- Supports AMD’s Cool ‘n’ Quiet

TM

Technology

- Chipset capable to FSB 1000 MHz (2.0 GT/s)

- Supports Untied Overclocking Technology (see CAUTION 1)

- Supports Hyper-Transport Technology

Chipset - NVIDIA

®

GeForce 6100 / nForce 430 or

GeForce 6150SE / nForce 430 (see CAUTION 2)

Memory - 2 x DDR DIMM slots

- Support DDR400/333/266

- Max. capacity: 2GB

Hybrid Booster - CPU Frequency Stepless Control (see CAUTION 3)

- ASRock U-COP (see CAUTION 4)

- Boot Failure Guard (B.F.G.)

Expansion Slot - 2 x PCI slots

- 1 x PCI Express x16 slot

- 1 x PCI Express x1 slot

- 1 x HDMR slot

Graphics - Integrated NVIDIA

®

GeForce6-class graphics

- DX9.0 VGA, Pixel Shader 3.0

- Max. shared memory 256MB

Audio - 7.1 CH Windows

®

Vista

TM

Basic Level HD Audio

(ALC883 Audio Codec)

LAN - Realtek PHY RTL8201CL

- Speed: 10/100 Ethernet

- Supports Wake-On-LAN

Rear Panel I/O HD 8CH I/O

- 1 x PS/2 Mouse Port

- 1 x PS/2 Keyboard Port

- 1 x VGA Port

- 1 x Parallel Port (ECP/EPP Support)

- 4 x Ready-to-Use USB 2.0 Ports

- 1 x RJ-45 Port

- HD Audio Jack: Side Speaker/Rear Speaker/Central/Bass/

Line in/Front Speaker/Microphone (see CAUTION 5)

66

6

ASRock K8NF6P-VSTA Motherboard

EnglishEnglish

English

Connector - 4 x Serial ATAII 3.0Gb/s connectors, support RAID (RAID 0,

RAID 1, RAID 0+1, JBOD, RAID 5), NCQ and “Hot Plug”

functions (see CAUTION 6)

- 1 x ATA133 IDE connector (supports 2 x IDE devices)

- 1 x Floppy connector

- 1 x IR header

- 1 x Game header

- 1 x COM port header

- CPU/Chassis FAN connector

- 20 pin ATX power connector

- 4 pin 12V power connector

- CD in header

- Front panel audio connector

- 3 x USB 2.0 headers (support 6 USB 2.0 ports)

(see CAUTION 7)

BIOS Feature - 4Mb AMI BIOS

- AMI Legal BIOS

- Supports “Plug and Play”

- ACPI 1.1 Compliance Wake Up Events

- Supports jumperfree

- SMBIOS 2.3.1 Support

Support CD - Drivers, Utilities, AntiVirus Software (Trial Version)

Hardware - CPU Temperature Sensing

Monitor - Chassis Temperature Sensing

- CPU Fan Tachometer

- Chassis Fan Tachometer

- CPU Quiet Fan

- Voltage Monitoring: +12V, +5V, +3.3V, Vcore

OS - Microsoft

®

Windows

®

2000/XP/XP 64-bit/Vista

TM

/

Vista

TM

64-bit compliant (see CAUTION 8)

Certifications - FCC, CE, Microsoft

®

WHQL Certificated

WARNING

Please realize that there is a certain risk involved with overclocking, including adjusting

the setting in the BIOS, applying Untied Overclocking Technology, or using the third-

party overclocking tools. Overclocking may affect your system stability, or even

cause damage to the components and devices of your system. It should be done at

your own risk and expense. We are not responsible for possible damage caused by

overclocking.

77

7

ASRock K8NF6P-VSTA Motherboard

EnglishEnglish

English

CAUTION!

1. This motherboard supports Untied Overclocking Technology. Please read “Un-

tied Overclocking Technology” on page 23 for details.

2. Both NVIDIA

®

GeForce 6100 / nForce 430 and GeForce 6150SE / nForce 430

refer to the same chipset. If you install NVIDIA

®

driver with 91.63 version or

above under Windows

®

2000 / XP / XP 64-bit, or install NVIDIA

®

driver with

97.19 version or above under Windows

®

Vista

TM

/ Vista

TM

64-bit, the chipset

name will be GeForce 6150SE / nForce 430 instead of GeForce 6100 / nForce

430. However, the difference in device name under Windows

®

does not affect

any specification and feature of this motherboard.

3. Although this motherboard offers stepless control, it is not recommended to

perform over-clocking. Frequencies other than the recommended CPU bus

frequencies may cause the instability of the system or damage the CPU.

4. While CPU overheat is detected, the system will automatically shutdown.

Before you resume the system, please check if the CPU fan on the motherboard

functions properly and unplug the power cord, then plug it back again. To

improve heat dissipation, remember to spray thermal grease between the

CPU and the heatsink when you install the PC system.

5. For microphone input, this motherboard supports both stereo and mono modes.

For audio output, this motherboard supports 2-channel, 4-channel, 6-channel,

and 8-channel modes. Please check the table on page 3 for proper connection.

6. Before installing SATAII hard disk to SATAII connector, please read the “SATAII

Hard Disk Setup Guide” on page 18 to adjust your SATAII hard disk drive to

SATAII mode. You can also connect SATA hard disk to SATAII connector

directly.

7. Power Management for USB 2.0 works fine under Microsoft

®

Windows

®

Vista

TM

64-bit / Vista

TM

/ XP 64-bit / XP SP1 or SP2 / 2000 SP4.

8. Microsoft

®

Windows

®

Vista

TM

/ Vista

TM

64-bit driver keeps on updating now. As

long as we have the latest driver, we will update it to our website in the future.

Please visit our website for Microsoft

®

Windows

®

Vista

TM

/ Vista

TM

64-bit driver

and related information.

ASRock website http://www.asrock.com

88

8

ASRock K8NF6P-VSTA Motherboard

EnglishEnglish

English

1.31.3

1.3

Minimum Hardware RMinimum Hardware R

Minimum Hardware R

equirement Tequirement T

equirement T

able for Wable for W

able for W

indowsindows

indows

®®

®

VistaVista

Vista

TMTM

TM

Basic Logo Basic Logo

Basic Logo

For system integrators and users who purchase our motherboard and

plan to submit Windows

®

Vista

TM

Basic logo, please follow the below

table for minimum hardware requirement.

CPU Sempron 2500+

Memory 512MB Single Channel*

VGA DX9.0 with WDDM Driver

* If you use onboard VGA with total system memory size 512MB and plan to

submit Windows

®

Vista

TM

Basic logo, please adjust the shared memory size of

onboard VGA to 64MB. If you use onboard VGA with total system memory size above

512MB and plan to submit Windows

®

Vista

TM

Basic logo, please adjust the shared

memory size of onboard VGA to 128MB or above.

99

9

ASRock K8NF6P-VSTA Motherboard

2.2.

2.

InstallationInstallation

Installation

Pre-installation PrecautionsPre-installation Precautions

Pre-installation Precautions

Take note of the following precautions before you install mother-

board components or change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any

component. Failure to do so may cause severe damage to the

motherboard, peripherals, and/or components.

2. To avoid damaging the motherboard components due to static

electricity, NEVER place your motherboard directly on the car-

pet or the like. Also remember to use a grounded wrist strap or

touch a safety grounded object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a

grounded antstatic pad or in the bag that comes with the

component.

5. When placing screws into the screw holes to secure the

motherboard to the chassis, please do not over-tighten the screws!

Doing so may damage the motherboard.

2.12.1

2.1

CPU InstallationCPU Installation

CPU Installation

Step 1. Unlock the socket by lifting the lever up to a 90° angle.

Step 2. Position the CPU directly above the socket such that the CPU corner with

the golden triangle matches the socket corner with a small triangle.

Step 3. Carefully insert the CPU into the socket until it fits in place.

The CPU fits only in one correct orientation. DO NOT force the CPU

into the socket to avoid bending of the pins.

Step 4. When the CPU is in place, press it firmly on the socket while you push

down the socket lever to secure the CPU. The lever clicks on the side tab

to indicate that it is locked.

Step 5. Install CPU fan and heatsink. For proper installation, please kindly refer to

the instruction manuals of your CPU fan and heatsink vendors.

EnglishEnglish

English

1010

10

ASRock K8NF6P-VSTA Motherboard

EnglishEnglish

English

2.22.2

2.2

Installation of Memory Modules (DIMM)Installation of Memory Modules (DIMM)

Installation of Memory Modules (DIMM)

This motherboard is equipped with two 184-pin DDR (Double Data Rate) DIMM slots.

Please make sure to disconnect power supply before adding or

removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.

Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break

on the slot.

The DIMM only fits in one correct orientation. It will cause permanent

damage to the motherboard and the DIMM if you force the DIMM into

the slot at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully

snap back in place and the DIMM is properly seated.

1111

11

ASRock K8NF6P-VSTA Motherboard

EnglishEnglish

English

2.32.3

2.3

Expansion Slots (PCI, HDMR and PCI Express Slots)Expansion Slots (PCI, HDMR and PCI Express Slots)

Expansion Slots (PCI, HDMR and PCI Express Slots)

There are 2 PCI slots, 1 HDMR slot and 2 PCI Express slots on this motherboard.

PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI

interface.

HDMR slot: HDMR slot is used to insert a HDMR card with v.92 Modem

functionality. The HDMR slot is shared with PCIE2 slot; you can only

choose either PCIE2 slot or HDMR slot to use.

PCIE Slots: PCIE1 (PCIE x16 slot) is used for PCI Express cards with x16 lane

width graphics cards.

PCIE2 (PCIE x1 slot) is used for PCI Express cards with x1 lane

width cards, such as Gigabit LAN card, SATA2 card, etc.

Installing an expansion cardInstalling an expansion card

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power

supply is switched off or the power cord is unplugged. Please read the

documentation of the expansion card and make necessary hardware

settings for the card before you start the installation.

Step 2. Remove the bracket facing the slot that you intend to use. Keep the screws

for later use.

Step 3. Align the card connector with the slot and press firmly until the card is

completely seated on the slot.

Step 4. Fasten the card to the chassis with screws.

1212

12

ASRock K8NF6P-VSTA Motherboard

EnglishEnglish

English

2.4 Easy Multi Monitor Feature2.4 Easy Multi Monitor Feature

2.4 Easy Multi Monitor Feature

This motherboard supports Multi Monitor upgrade. With the internal onboard VGA

and the external add-on PCI Express VGA card, you can easily enjoy the benefits

of Multi Monitor feature. Please refer to the following steps to set up a multi

monitor environment:

1. Install the NVIDIA

®

PCI Express VGA card to PCIE1 (PCIE x16 slot). Please refer

to page 11 for proper expansion card installation procedures for details.

2. Connect the D-Sub input monitor cable to the VGA/D-Sub port on the I/O panel

of this motherboard. Connect another D-Sub input monitor cable to the

VGA/D-Sub connector of the add-on PCI Express VGA card. Connect the DVI-D

input monitor cable to the VGA/DVI-D connector of the add-on PCI Express VGA

card.

3. Boot your system. Press <F2> to enter BIOS setup. Enter “Share Memory”

option to adjust the memory capability to [16MB], [32MB], [64MB], [128MB], or

[256MB] to enable the function of onboard VGA/D-sub. Please make sure that

the value you select is less than the total capability of the system memory. If

you do not adjust the BIOS setup, the default value of “Share Memory”, [Auto],

will disable onboard VGA/D-Sub function when the add-on VGA card is

inserted to this motherboard.

4. Install the onboard VGA driver to your system. If you have installed the

onboard VGA driver already, there is no need to install it again.

5. Set up a multi-monitor display. Right click the desktop, choose “Properties”, and

select the “Settings” tab so that you can adjust the parameters of the multi-

monitor according to the steps below. (The item names and operation

procedures described in this step are under Windows

®

XP environment. If you

install other Windows

®

OS, the item names and operation procedures may be

similar.)

A. Click the “Identify” button to display a large number on each monitor.

B. Right-click the display icon in the Display Properties dialog that you wish to

be your primary monitor, and then select “Primary”. When you use multiple

monitors with your card, one monitor will always be Primary, and all

additional monitors will be designated as Secondary.

C. Select the display icon identified by the number 2.

D. Click “Extend my Windows desktop onto this monitor”.

E. Right-click the display icon and select “Attached”, if necessary.

F. Set the “Screen Resolution” and “Color Quality” as appropriate for the

second monitor. Click “Apply” or “OK” to apply these new values.

G. Repeat steps C through E for the diaplay icon identified by the number one,

two, and three.

1313

13

ASRock K8NF6P-VSTA Motherboard

Open

2.52.5

2.5

Jumpers SetupJumpers Setup

Jumpers Setup

The illustration shows how jumpers are

setup. When the jumper cap is placed on

pins, the jumper is “Short”. If no jumper cap

is placed on pins, the jumper is “Open”. The

illustration shows a 3-pin jumper whose pin1

and pin2 are “Short” when jumper cap is

placed on these 2 pins.

Jumper Setting

PS2_USB_PW1 Short pin2, pin3 to enable

(see p.2, No. 1) +5VSB (standby) for PS/2 or

USB wake up events.

Note: To select +5VSB, it requires 2 Amp and higher standby current provided by

power supply.

Clear CMOS Jumper

(CLRCMOS1)

(see p.2, No. 19)

Note: CLRCMOS1 allows you to clear the data in CMOS. The data in CMOS includes

system setup information such as system password, date, time, and system

setup parameters. To clear and reset the system parameters to default setup,

please turn off the computer and unplug the power cord from the power

supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3

on CLRCMOS1 for 5 seconds. However, please do not clear the CMOS right

after you update the BIOS. If you need to clear the CMOS when you just finish

updating the BIOS, you must boot up the system first, and then shut it down

before you do the clear-CMOS action.

Short

Clear CMOSDefault

EnglishEnglish

English

6. Use Multi Monitor feature. Click and drag the display icons to positions

representing the physical setup of your monitors that you would like to use. The

placement of display icons determines how you move items from one monitor to

another.

1414

14

ASRock K8NF6P-VSTA Motherboard

EnglishEnglish

English

2.6 Onboard Headers and Connectors2.6 Onboard Headers and Connectors

2.6 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place

jumper caps over these headers and connectors. Placing jumper caps

over the headers and connectors will cause permanent damage of the

motherboard!

•

Floppy Connector

(33-pin FLOPPY1)

(see p.2 No. 18)

Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the

connector.

Primary IDE connector (Blue)

(39-pin IDE1, see p.2 No. 4)

Note: Please refer to the instruction of your IDE device vendor for the details.

Serial ATAII Connectors These Serial ATAII (SATAII)

(SATAII_1: see p.2, No. 5) connectors support SATAII

(SATAII_2: see p.2, No. 6) or SATA hard disk for internal

(SATAII_3: see p.2, No. 7) storage devices. The current

(SATAII_4: see p.2, No. 8) SATAII interface allows up to

3.0 Gb/s data transfer rate.

Serial ATA (SATA) Either end of the SATA data cable

Data Cable can be connected to the SATA /

(Optional) SATAII hard disk or the SATAII

connector on the motherboard.

Serial ATA (SATA) Please connect the black end of

Power Cable SATA power cable to the power

(Optional) connector on each drive. Then

connect the white end of SATA

power cable to the power

connector of the power supply.

connect the black end

to the IDE devices

connect the blue end

to the motherboard

80-conductor ATA 66/100/133 cable

the red-striped side to Pin1

connect to the

power supply

connect to the SATA

HDD power connector

SATAII_1

SATAII_2

SATAII_3

SATAII_4

1515

15

ASRock K8NF6P-VSTA Motherboard

EnglishEnglish

English

1. High Definition Audio supports Jack Sensing, but the panel wire on the

chassis must support HDA to function correctly. Please follow the

instruction in our manual and chassis manual to install your system.

2. If you use AC’97 audio panel, please install it to the front panel audio

header as below:

A. Connect Mic_IN (MIC) to MIC2_L.

B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.

C. Connect Ground (GND) to Ground (GND).

USB 2.0 Headers Besides four default USB 2.0

(9-pin USB6_7) ports on the I/O panel, there are

(see p.2 No. 11) three USB 2.0 headers on this

motherboard. Each USB 2.0

header cansupport two USB

2.0 ports.

(9-pin USB8_9)

(see p.2 No. 12)

(9-pin USB4_5)

(see p.2 No. 13)

Infrared Module Header This header supports an

(5-pin IR1) optional wireless transmitting

(see p.2 No. 17) and receiving infrared module.

Internal Audio Connectors This connector allows you

(4-pin CD1) to receive stereo audio input

(CD1: see p.2 No. 27) from sound sources such as

a CD-ROM, DVD-ROM, TV

tuner card, or MPEG card.

Front Panel Audio Header This is an interface for the front

(9-pin HD_AUDIO1) panel audio cable that allows

(see p.2, No. 23) convenient connection and

control of audio devices.

CD1

1616

16

ASRock K8NF6P-VSTA Motherboard

EnglishEnglish

English

System Panel Header This header accommodates

(9-pin PANEL1) several system front panel

(see p.2 No. 15) functions.

Chassis Speaker Header Please connect the chassis

(4-pin SPEAKER 1) speaker to this header.

(see p.2 No. 16)

Chassis Fan Connector Please connect a chassis fan

(3-pin CHA_FAN1) cable to this connector and

(see p.2 No. 14) match the black wire to the

ground pin.

CPU Fan Connector Please connect the CPU fan

(4-pin CPU_FAN1) cable to this connector and

(see p.2 No. 2) match the black wire to the

ground pin.

Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin

CPU fan still can work successfully even without the fan speed control function.

If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this

motherboard, please connect it to Pin 1-3.

3-Pin Fan Installation

Pin 1-3 Connected

ATX Power Connector Please connect an ATX power

(20-pin ATXPWR1) supply to this connector.

(see p.2 No. 28)

4

3

2

1

D. MIC_RET and OUT_RET are for HD audio panel only. You don’t

need to connect them for AC’97 audio panel.

E. Enter BIOS Setup Utility. Enter Advanced Settings, and then select

Chipset Configuration. Set the Front Panel Control option from

[Auto] to [Enabled].

F. Enter Windows system. Click the icon on the lower right hand

taskbar to enter Realtek HD Audio Manager. Click “Audio I/O”, select

“Connector Settings” , choose “Disable front panel jack

detection”, and save the change by clicking “OK”.

1717

17

ASRock K8NF6P-VSTA Motherboard

EnglishEnglish

English

t

e

ATX 12V Power Connector Please note that it is necessary

(4-pin ATX12V1) to connect a power supply with

(see p.2 No. 10) ATX 12V plug to this connector.

Failing to do so will cause power

up failure.

Game Port Header Connect a Game cable to this

(15-pin GAME1) header if the Game port bracket

(see p.2 No. 20) is installed.

Serial port Header This COM1 header

(9-pin COM1) supports a serial port module.

(see p.2 No..29)

1818

18

ASRock K8NF6P-VSTA Motherboard

EnglishEnglish

English

2.72.7

2.7

SASA

SA

TT

T

AII Hard Disk Setup GuideAII Hard Disk Setup Guide

AII Hard Disk Setup Guide

Before installing SATAII hard disk to your computer, please carefully read below

SATAII hard disk setup guide. Some default setting of SATAII hard disks may not be

at SATAII mode, which operate with the best performance. In order to enable SATAII

function, please follow the below instruction with different vendors to correctly

adjust your SATAII hard disk to SATAII mode in advance; otherwise, your SATAII hard

disk may fail to run at SATAII mode.

Western Digital

If pin 5 and pin 6 are shorted, SATA 1.5Gb/s will be enabled.

On the other hand, if you want to enable SATAII 3.0Gb/s, please remove the jumpers

from pin 5 and pin 6.

SAMSUNG

If pin 3 and pin 4 are shorted, SATA 1.5Gb/s will be enabled.

On the other hand, if you want to enable SATAII 3.0Gb/s, please remove the jumpers

from pin 3 and pin 4.

HITACHI

Please use the Feature Tool, a DOS-bootable tool, for changing various ATA features.

Please visit HITACHI’s website for details:

http://www.hitachigst.com/hdd/support/download.htm

The above examples are just for your reference. For different SATAII hard

disk products of different vendors, the jumper pin setting methods may not

be the same. Please visit the vendors’ website for the updates.

1919

19

ASRock K8NF6P-VSTA Motherboard

EnglishEnglish

English

2.82.8

2.8

Serial ASerial A

Serial A

TT

T

A (SAA (SA

A (SA

TT

T

A) / Serial AA) / Serial A

A) / Serial A

TT

T

AII (SAAII (SA

AII (SA

TT

T

AII) Hard DisksAII) Hard Disks

AII) Hard Disks

InstallationInstallation

Installation

This motherboard adopts NVIDIA

®

GeForce 6100 / nForce 430 or GeForce 6150SE

/ nForce 430 chipset that supports Serial ATA (SATA) / Serial ATAII (SATAII) hard

disks and RAID functions. You may install SATA / SATAII hard disks on this

motherboard for internal storage devices. This section will guide you to install the

SATA / SATAII hard disks.

STEP 1: Install the SATA / SATAII hard disks into the drive bays of your chassis.

STEP 2: Connect the SATA power cable to the SATA / SATAII hard disk.

STEP 3: Connect one end of the SATA data cable to the motherboard’s SATAII

connector.

STEP 4: Connect the other end of the SATA data cable to the SATA / SATAII hard

disk.

2.92.9

2.9

Hot Plug and Hot Swap FHot Plug and Hot Swap F

Hot Plug and Hot Swap F

unctions for SAunctions for SA

unctions for SA

TT

T

A / SAA / SA

A / SA

TT

T

AIIAII

AII

HDDsHDDs

HDDs

This motherboard supports Hot Plug and Hot Swap functions for SATA / SATAII

Devices.

NOTE

What is Hot Plug Function?

If the SATA / SATAII HDDs are NOT set for RAID configuration, it is

called “Hot Plug” for the action to insert and remove the SATA / SATAII

HDDs while the system is still power-on and in working condition.

However, please note that it cannot perform Hot Plug if the OS has

been installed into the SATA / SATAII HDD.

What is Hot Swap Function?

If SATA / SATAII HDDs are built as RAID1 then it is called “Hot Swap”

for the action to insert and remove the SATA / SATAII HDDs while the

system is still power-on and in working condition.

2.102.10

2.10

Driver Installation GuideDriver Installation Guide

Driver Installation Guide

To install the drivers to your system, please insert the support CD to your optical

drive first. Then, the drivers compatible to your system can be auto-detected and

listed on the support CD driver page. Please follow the order from up to bottom

side to install those required drivers. Therefore, the drivers you install can work

properly.

2020

20

ASRock K8NF6P-VSTA Motherboard

EnglishEnglish

English

2.112.11

2.11

HDMR Card and Driver Installation HDMR Card and Driver Installation

HDMR Card and Driver Installation

If you do not insert HDMR card to this motherboard, and you finish installing all

drivers to your system now, but in the future, you plan to use HDMR card function

on this motherboard, please follow the steps below then.

1. Insert HDMR card to HDMR slot on this motherboard. Please make sure that the

HDMR card is completely seated on the slot.

2. Install HDMR card driver from our support CD to your system.

3. Reboot your system.

2.122.12

2.12

Installing WindowsInstalling Windows

Installing Windows

®

2000 / XP / XP 64-bit / Vista 2000 / XP / XP 64-bit / Vista

2000 / XP / XP 64-bit / Vista

TMTM

TM

/ Vista/ Vista

/ Vista

TMTM

TM

64-bit Without RAID Functions 64-bit Without RAID Functions

64-bit Without RAID Functions

2.132.13

2.13

Installing WindowsInstalling Windows

Installing Windows

®

2000 / XP / XP 64-bit / Vista 2000 / XP / XP 64-bit / Vista

2000 / XP / XP 64-bit / Vista

TMTM

TM

/ Vista/ Vista

/ Vista

TMTM

TM

64-bit With RAID Functions 64-bit With RAID Functions

64-bit With RAID Functions

If you want to install Windows

®

2000, Windows

®

XP, Windows

®

XP 64-bit, Windows

®

Vista

TM

or Windows

®

Vista

TM

64-bit OS on your SATA / SATAII HDDs with RAID

functions, please follow below procedures according to the OS you install.

The installation procedures for Windows

®

Vista

TM

/ Vista

TM

64-bit are subject to

change. Please visit our website for the updates of Windows

®

Vista

TM

/ Vista

TM

64-bit

driver and related information in the future.

If you just want to install Windows

®

2000, Windows

®

XP, Windows

®

XP 64-bit,

Windows

®

Vista

TM

or Windows

®

Vista

TM

64-bit on your SATA / SATAII HDDs without

RAID functions, you don’t have to make a SATA / SATAII driver diskette. Besides,

there is no need for you to change the BIOS setting. You can start to install Windows

®

2000, Windows

®

XP, Windows

®

XP 64-bit, Windows

®

Vista

TM

or Windows

®

Vista

TM

64-bit on your system directly.

1. The installation procedures for Windows

®

Vista

TM

/ Vista

TM

64-bit are subject to

change. Please visit our website for the updates of Windows

®

Vista

TM

/ Vista

TM

64-bit driver and related information in the future.

2. Before installing Windows

®

2000 to your system, your Windows

®

2000 optical

disk is supposed to include SP4. If there is no SP4 included in your disk, please

visit the below website for proper procedures of making a SP4 disk:

http://www.microsoft.com/Windows2000/downloads/servicepacks/sp4/spdeploy.

htm#the_integrated_installation_fmay

La pagina sta caricando ...

ASROCK K8NF6P-VSTA Manuale del proprietario

ASROCK K8NF6P-VSTA Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti