VuPoint RVCM11W Guida d'installazione

VUpoint

Cube Indoor P2P IP Camera

Model: RVCM11W

EN FR IT ES

Installation Guide

Language Page

1

21

43

63

VUpoint

Cube Indoor P2P IP Camera

Model: RVCM11W

EN

Installation Guide

2

Safety Precautions

These instructions are intended to ensure that the user can use the product correctly to

avoid danger or property loss.

WARNINGS:

 Installation or usage of this product that is not in accordance with the intended

use as defined by the supplier and as described in the instructional materials

can result in damage, injury, or death.

 Make sure this product is not accessible by children and those for whom

operation of the system is not intended.

 All installation and operation should conform to your local electrical safety

codes. The power shall conform to the requirement in the SELV (Safety Extra

Low Voltage) and the Limited power source is rated 12V DC in the IEC60950-1.

 If the device is permanently connected to an electrical power supply, then the

connection should include an easily-accessible disconnection device, such as a

circuit breaker. Do not connect the two power supplying sources to the device

at the same time; it may result in device damage!

 Do not ever attempt to repair your device by yourself, as doing so could result

in damage, injury or death – always contact your installer / supplier agent for

service.

CAUTIONS:

 Make sure the power supply voltage is correct before using the camera.

 Do not drop the camera or subject it to physical shock.

 Do not touch sensor modules with fingers. If cleaning is necessary, use a clean

cloth with a bit of ethanol and wipe it gently.

 Do not aim the camera lens at the strong light such as sun or incandescent

lamp. The strong light can cause fatal damage to the camera.

 The sensor may be burned out by a laser beam, so when any laser equipment is

being used, make sure that the surface of the sensor not be exposed to the laser

beam.

 Do not place the camera in extremely hot, cold temperatures (the operating

temperature should be between -10°C ~ +50°C).

 To avoid heat accumulation, good ventilation is required for a proper operating

environment.

 Keep the camera away from water and any liquid.

 While shipping, the camera should be packed in its original packing.

NOTE: We assume no liability or responsibility for all the fires or electrical shock

caused by improper handling or installation. We are not liable for any problems caused

by unauthorized modification or attempted repair.

3

Introduction

RISCO Group presents VUpoint, a revolutionary live video verification solution

which seamlessly integrates IP Cameras within RISCO’s professional security

systems. Powered by the RISCO Cloud (RISCO Application Server), VUpoint

provides an unprecedented level of security and live video monitoring

capabilities to monitoring stations and end-users alike. The RISCO cube indoor

IP Camera is an important part of this solution and

is easily controlled through

RISCO’s intuitive Web and Smartphone applications.

Features

 Plug & Play installation

 1.3 Megapixel

 Color HD

 Day/Night

 IR LED Length 10m

 Two-way audio

Components and Accessories

RISCO IP camera and

mounting bracket:

Installation guide

4

IP Camera Components and Dimensions

5

Figure 1 IP Camera Components

Label Description

1

Network port (Wireless connection mode is available as well)

2

Reset/WPS (Wi-Fi Protected Setup) button

3 Digital input/output

4 Power port

5 Built-in speaker

6 Micro SD card slot

7 Indicator light

8 Built-in MIC

9 IR LED

10 PIR （Sense IR ray, trigger alarm）

6

Note:

 For reset (used to return the camera settings to factory default mode), long

press for 15 seconds and then the light turns off

 For WPS (Wi-Fi Protected Setup), one quick press.

Indication Status

Red light normally on

Booting

Green light slow

flashing

Booting completed, await WiFi config, enter smart config status;

Green light quick

flashing

WiFi smart config in progress, including WPS (WiFi Protected

Setup), management frame and etc.

Green light normally

on

Wifi connection succeeded, operate normally.

Red and green lights

flash alternately

Device upgrade

Red light slow flashing

Network connection failure or disconnection after network

connection success.

Red light quick

flashing

Device malfunction, fail to boot up; alarm or SD card

malfunction

7

Figure 2 IP Camera Dimensions

IP Camera Installation

After reading the installation instructions and before installing your IP camera,

prepare a plan for mounting the IP camera at your protected site. Correct

placement of your IP camera is crucial for optimal security-monitoring

performance. First, determine which areas need to be protected and then map

out the most optimal areas for installing your IP camera.

8

IMPORTANT! – Please make a record of the MAC

address located on the box or on the back cover of

the IP camera before installation. You may need it

during the network connection stage.

Mounting the IP Camera

The IP camera support two mounting options; ceiling and wall mount (see Figure

3, below).

Figure 3 Wall / Ceiling Mount

IMPORTANT- Please make sure the installation surface can support at least 3

times the weight of the camera and the bracket.

Step Description

1 Place the installation positioning template on the installation surface such as

ceiling or wall.

2 Make holes in the installation surface according to the installation positioning

template.

3 Insert the expansion bolts from the accessories bag into the holes you just made.

4 Position the IP camera base over the holes

MAC address

9

Step Description

5 Use the screws from the accessories bag to secure the IP camera firmly.

6 Loosen the adjust knob and adjust the IP camera to the correct surveillance

position according to your actual requirements.

7 Secure the adjust knob to fix the IP camera.

Powering-up the IP Camera

1. Connect power to the Power port on the IP camera.

2. Connect power to an electrical outlet. When the IP camera boots up, the

GREEN power indicator light turns on.

Connecting the IP Camera to the Network

The IP camera supports several network connection options including LAN and

Wireless.

Connecting to a LAN Network

Connecting the IP camera to a network using the LAN (Local Area Network)

enables easy connection and setup with compatible APs (Access Points), e.g.

gateway or router.

1. Connect the incoming network cable to the Network port on the IP camera.

2. Wait for the slow flashing GREEN network indicator to stop flashing. The

GREEN network indicator lights to indicate that your IP camera is now

connected to the network. Continue as explained in Defining IP Camera

Settings.

Connecting to a Wireless Network using WPS

Connecting the IP camera to a wireless network using WPS (Wi-Fi Protected

Setup) requires that the router supports WPS functionality.

NOTE – Some routers have a virtual button on their management software.

(Refer to the router’s documentation for details about using its WPS functions).

10

1. Once the power cord is connected, wait for slow flashing GREEN network

indicator.

2. Momentarily press the WPS button on the IP camera and hold down the

WPS button on the router for 2 seconds. The GREEN network indicator light

indicates that your IP camera is now connected to the network. Continue as

explained in Defining IP Camera Settings.

Connecting to a Wireless Network using the RISCO Cloud

Connecting the IP camera to a wireless network using the RISCO Cloud (RISCO

Application Server) requires that you first physically connect the IP camera to the

router and then, from the RISCO Cloud Installer Application, define the IP

camera settings and establish a wireless connection. Once a wireless connection

has been established the IP camera can then be disconnected from the router and

installed.

1. Connect the incoming network cable to the Network port on the IP camera.

2. Wait for the slow flashing GREEN network indicator while the IP camera

automatically connects to the RISCO Cloud (RISCO Application Server). The

GREEN network indicator light indicates that your IP camera is now

connected to the network. Continue as explained in Defining IP Camera

Settings.

3. Once a wireless connection has been established, disconnect the IP camera

from the router and install it anywhere within the monitored area.

11

IP Cameras and the RISCO Cloud Installer Application

The RISCO Cloud Installer Application provides an interface to your control

panel from a local or remote PC via the Web. This enables you to add IP cameras

and define camera and event alarm trigger settings.

IMPORTANT – A control panel must first be defined in RISCO Cloud in order

to accept IP cameras and define camera settings (Refer to the RISCO Cloud

Installer Application Manual)

Defining IP Camera Settings

Once you have connected the IP camera to the network (refer to, Connecting the

IP Camera to the Network) you can define the camera settings.

To define IP camera settings:

1. Log into the Installer Administration application using the Web page address

supplied by your service provider and enter your user name and password.

NOTE – It is recommended to use Google Chrome or Mozilla Firefox to log into

the Installer Administration application.

2. Select the Control Panels List link. The Control Panels List page is displayed.

Figure 4 Control Panels List Page

3. From the Control Panels List page, select the Control Panel you wish to view.

The Control Panels Update page is displayed.

12

Figure 5 Control Panel Update Page

4. Click the Network Cameras link in the left-hand column; the IP Camera List

page is displayed.

Figure 6 IP Cameras List

5. Click Add Camera; the Add Camera dialog box is displayed.

Figure 7 Add Camera

6. Define the following fields in the Add Camera dialog box.

Field Description

Label Enter a name for the camera

Partitions Select the partition(s) from the list of defined partitions

Type Choose the RISCO camera type (for ONVIF or Generic camera type settings,

refer to the RISCO Cloud Installer Application Manual)

MAC

Address

Enter the MAC address into this field. The MAC address (media access

control address) is the unique identifier assigned to the IP camera for

communications on the physical network.

NOTE: The MAC address is case sensitive and should be entered exactly as

it is shown on the box or on the back cover of the IP camera, e.g.

AA:BB:CC:DD:EE:FF

13

7. Click Add.

If the “Connect to WiFi” message is displayed, go straight to step 8.

Figure 8 Connect to WiFi message

NOTE – This message is only relevant for IP cameras that are physically

connected to the LAN network via the router.

8. Select one of the following options:

Connect to Wi-Fi – to establish a wireless network connection (go to step 9 to

connect the IP camera to the wireless network).

Not Now – to establish a LAN network connection (skip the wireless network

connection steps 9, 10 and 11 and connect the IP camera to the LAN network).

9. If you selected the “Connect to Wi-Fi” option, a list of available wireless

networks is displayed.

Figure 9 List of available wireless networks

10. Select a wireless network from the available list and click Connect.

NOTE – If your network is password protected, a password must be entered into

the displayed password screen.

11. Click OK to establish the wireless connection (Refer to Error! Reference

source not found.).

IMPORTANT – Once a wireless connection has been established, don’t forget to

disconnect the IP camera Ethernet cable from the router.

14

12. Once the “camera is ready for use” message is displayed, click OK. The

defined IP camera is displayed in the IP Cameras page.

Figure 10 IP Camera List

NOTE – You also have the option to edit or delete the selected IP camera.

Defining Camera Trigger Settings

Any event from the following list can be defined to trigger an alarm.

Partition Events

Fire Alarm Panic Alarm Medical Alarm Alarm

Full Arm Part Arm Disarmed Duress

Tamper 24 HR-X Alarm Water Alarm Gas Alarm

Environ. Alarm No Motion Alarm Exit Alarm Low Temperature

Detector Events

Alarm Zone Bypassed Zone Un-bypassed Zone Tamper

To define camera trigger settings:

1. From the Control Panel Cameras page, click the Triggers tab, the Camera

Triggers List page is displayed.

Figure 11 Camera Triggers List

15

2. Click Add Trigger; the Add Triggers dialog box appears.

Figure 12 Add Trigger

3. Define the following fields in the Add Trigger dialog box:

Field Description Event Type

Label Enter a name for the camera trigger Partition and Detector events

Camera Choose a camera from the list Partition and Detector events

Event Type Choose an event type from the list Partition and Detector events

Event Choose the event from the list, e.g.

alarm, duress, etc.

Partition and Detector events

Additional fields are displayed in the Add Trigger dialog box according to the

event type that you selected (see examples below for Partition and Detector event

types).

Figure 13 Add Partition Event Trigger Figure 14 Add Detector Event Trigger

16

4. Define the following fields in the Add Trigger dialog box according to the

event type that you selected.

Field Description Event Type

Partition(s) Select the partition(s) from the list.

NOTE – Only partitions associated with

the camera are displayed.

Partition events only

Detectors Select the detector from the list Detector events only

5. Define the following image (still) and clip (video) definitions:

Field Description

Images

(still)

Pre-event starting time (sec) – time, before the actual event occurred, to

start displaying still images.

Number of images – number of still images to display.

Interval between images (sec) – time required between each still image.

Clips

(video)

Pre-event starting time (sec) – time, before the actual event occurred, to

start displaying video clip.

Duration (sec) – total duration of the video clip

NOTE – These fields are currently locked and the default parameters

cannot be changed.

6. Once finished, click Done. The defined camera trigger is displayed in the

Camera Triggers List page.

Figure 15 Camera Triggers List

NOTE – You also have the options to edit , create a duplicate , or to delete

the selected camera trigger.

IMPORTANT – No two camera triggers can be defined as identical. If a camera

trigger is duplicated, the event, camera or both definitions must be changed.

17

Product Specification

Model RVCM11W0000B

Camera

Image Sensor 1/3” 1.3Megapixel CMOS

Effective Pixels

1280(H)x960(V)

Scanning System Progressive

Electronic Shutter Speed Auto/Manual, 1/3(4)~1/30000

Min. Illumination

0.85lux/F2.5(color),0lux/F2.5(IR on)

S/N Ratio

More than 50dB

Video Output

N/A

Camera Features

Max. LEDs Length 10m

Day/Night Auto(ICR) / Color / B/W

Backlight Compensation BLC / HLC / DWDR

White Balance Auto/Manual

Gain Control Auto/Manual

Noise Reduction 3D

Lens

Focal Length 2.8mm

Max Aperture F2.5

Focus Control Manual

Angle of View 95°

Lens Type Fixed Lens

Mount Type Board-in Type

Video

Compression H.264/MJEPG

Resolution 1.3MP/720P/VGA/QVGA

Frame

Rate

Main Stream 1.3MP/720P(1~30fps)

Sub Stream VGA/QVGA(1~30fps)

Bit Rate

H.264: 32Kbps～8192Kbps

Audio

Compression G.711a;G.711Mu;AAC

Interface Built-in Mic/Speaker

18

Network

Ethernet RJ45

Wi-Fi

Wi-Fi(IEEE802.11b/g/n)

50m(open field)

Protocol

P2P, HTTP; HTTPS; TCP; IPV4/IPV6 ;UDP; RTSP; ICMP; RTP; DHCP; NTP;

IGMP; ARP; DNS; DDNS; SMTP; UPNP; Bonjour; Qos, FTP

Compatibility ONVIF CGI

Max. User Access 10 users

Smart Phone iPhone, iPad, Android

Auxiliary Interface

Memory Slot Micro SD, up to 128GB

RS485 N/A

Alarm 1 in/1 out

PIR Sensor Range Yes, 6m

USB Micro USB

General

Power Supply DC 12V

Power Consumption <4.5W

Working Environment -10°C~+45°C, Less than 95%RH

Ingress Protection N/A

Vandal Resistance N/A

Dimensions(W×D×H) Φ78.5mm×127.8mm

Weight 0.45KG with package

La pagina sta caricando ...

VuPoint RVCM11W Guida d'installazione

VuPoint RVCM11W Guida d'installazione

in altre lingue

Altri documenti