Whirlpool IWD 6085 (EU) Guida utente

Marca: Whirlpool

Modello: IWD 6085 (EU)

Categoria: Lavatrici

Tipo: Guida utente

Contents

Installation, 2-3

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Description of the washing machine

and starting a wash cycle, 4-5

Control panel

Indicator lights

Starting a wash cycle

Wash cycles, 6

Table of wash cycles

Personalisation, 7

Setting the temperature

Setting the spin speed

Functions

Detergents and laundry, 8

Detergent dispenser drawer

Bleach cycle

Preparing the laundry

Garments requiring special care

Load balancing system

Precautions and tips, 9

General safety

Disposal

Care and maintenance, 10

Cutting off the water or electricity supply

Cleaning the washing machine

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Troubleshooting, 11

Service, 12

IWD 6085

Instructions for use

WASHING MACHINE

English,1

Românã,13

Á ÚËÃÀÐ ÑÊÈ,25

Óêðà¿íñüêà,37

Installation

 This instruction manual should be kept in a safe

place for future reference. If the washing machine is

sold, transferred or moved, make sure that the

instruction manual remains with the machine so that

the new owner is able to familiarise himself/herself

with its operation and features.

 Read these instructions carefully: they contain vital

information relating to the safe installation and

operation of the appliance.

Unpacking and levelling

Unpacking

1. Remove the washing machine from its packaging.

2. Make sure that the washing machine has not been

damaged during the transportation process. If it has

been damaged, contact the retailer and do not

proceed any further with the installation process.

3. Remove the 3

protective screws (used

during transportation) and

the rubber washer with

the corresponding

spacer, located on the

rear part of the appliance

(see figure).

4. Close off the holes using the plastic plugs provided.

5. Keep all the parts in a safe place: you will need

them again if the washing machine needs to be

moved to another location.

 Packaging materials should not be used as toys for

children.

Levelling

1. Install the washing machine on a flat sturdy floor,

without resting it up against walls, furniture cabinets

or anything else.

2. If the floor is not

perfectly level, compen-

sate for any unevenness

by tightening or loosening

the adjustable front feet

(see figure); the angle of

inclination, measured in

relation to the worktop,

must not exceed 2°.

Levelling the machine correctly will provide it with

stability, help to avoid vibrations and excessive noise

and prevent it from shifting while it is operating. If it is

placed on carpet or a rug, adjust the feet in such a

way as to allow a sufficient ventilation space

underneath the washing machine.

Connecting the electricity and water

supplies

Connecting the water inlet hose

1. Connect the supply

pipe by screwing it to a

cold water tab using a ¾

gas threaded connection

(see figure).

Before performing the

connection, allow the

water to run freely until it

is perfectly clear.

2. Connect the inlet hose

to the washing machine

by screwing it onto the

corresponding water inlet

of the appliance, which is

situated on the top right-

hand side of the rear part

of the appliance (see

figure).

3. Make sure that the hose is not folded over or bent.

 The water pressure at the tap must fall within the

values indicated in the Technical details table (see

next page).

 If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

 Never use second-hand hoses.

 Use the ones supplied with the machine.

Technical data

Model

IWD 6085

Dimensions

width 59.5 cm

height 85 cm

depth 52,5 cm

Capacity

from 1 to 6 kg

Electrical

connections

please refer to the technical data

plate fixed to the machine

Water connections

maximum pressure 1 MPa (10 bar)

minimum pressure 0.05 MPa (0.5 bar)

drum capacity 46 litres

Spin speed

up to 800 rotations per minute

Energy rated

programmes

according to

regulation

EN 60456

programme 2; temperature 60°C;

using a load of 6 kg.

This appliance conforms to the

following EC Directives:

- 89/336/EEC dated 03/05/89

(Electromagnetic Compatibility) and

subsequent modifications

- 2002/96/EC

- 2006/95/EC Low Voltage)

65 - 100 cm

Connecting the drain hose

Connect the drain hose,

without bending it, to a

drainage duct or a wall

drain located at a height

between 65 and 100 cm

from the floor;

alternatively, rest it on

the side of a washbasin

or bathtub, fastening the

duct supplied to the tap

(see figure). The free end

of the hose should not

be underwater.

 We advise against the use of hose extensions; if it is

absolutely necessary, the extension must have the

same diameter as the original hose and must not

exceed 150 cm in length.

Electrical connections

Before plugging the appliance into the electricity

socket, make sure that:

 the socket is earthed and complies with all

applicable laws;

 the socket is able to withstand the maximum power

load of the appliance as indicated in the Technical

data table (see opposite);

 the power supply voltage falls within the values

indicated in the Technical data table (see opposite);

 the socket is compatible with the plug of the

washing machine. If this is not the case, replace

the socket or the plug.

 The washing machine must not be installed

outdoors, even in covered areas. It is extremely

dangerous to leave the appliance exposed to rain,

storms and other weather conditions.

 When the washing machine has been installed, the

electricity socket must be within easy reach.

 Do not use extension cords or multiple sockets.

 The cable should not be bent or compressed.

 The power supply cable must only be replaced by

authorised technicians.

Warning! The company shall not be held responsible

in the event that these regulations are not respected.

The first wash cycle

Once the appliance has been installed, and before

you use it for the first time, run a wash cycle with

detergent and no laundry, using the wash cycle 2.

Detergent dispenser drawer: used to dispense

detergents and washing additives (see Detergents

and laundry).

ON/OFF button: switches the washing machine on

and off.

WASH CYCLE knob: programmes the wash cycles.

During the wash cycle, the knob does not move.

FUNCTION buttons with indicator light: used to

select the available functions. The indicator light

corresponding to the selected function will remain lit.

TEMPERATURE knob: sets the temperature or the

cold wash cycle (see Personalisation).

SPIN SPEED knob: sets the spin speed or exclude

the spin cycle completely (see Personalisation).

DISPLAY: used to view the duration of the various

cycles available and the remaining time of a cycle in

progress; if the DELAY TIMER option has been

selected, the countdown to the start of the selected

cycle will appear.

DELAY TMER button

: press to set a delayed start

time for the selected wash cycle. The delay time will

be shown on the display.

WASH CYCLE PROGRESS

indicator light

s: used to

monitor the progress of the wash cycle.

The illuminated indicator light shows which phase is in

progress.

DOOR LOCKED indicator light: indicates whether

the door may be opened or not (see next page).

START/PAUSE button with indicator light: starts or

temporarily interrupts the wash cycles.

N.B. To pause the wash cycle in progress, press this

button; the corresponding indicator light will flash

orange, while the indicator light for the current wash

cycle phase will remain lit in a fixed manner. If the

DOOR LOCKED

indicator light is switched off, the

door may be opened.

To start the wash cycle from the point at which it was

interrupted, press this button again.

Standby mode

This washing machine, in compliance with new

energy saving regulations, is fitted with an automatic

standby system which is enabled after a few minutes

if no activity is detected. Press the ON-OFF button

briefly and wait for the machine to start up again.

Description of the washing machine

and starting a wash cycle

WASH CYCLE

PROGRESS

DOOR LOCKED

indicator light

START/

PAUSE

button with

indicator light

Control panel

Detergent dispenser drawer

ON/OFF

button

WASH CYCLE

knob

TEMPERATURE

knob

FUNCTION

buttons with

indicator lights

SPIN SPEED

knob

DISPLAY

DELAY TIMER

button

Indicator lights

The indicator lights provide important information.

This is what they can tell you:

Wash cycle phase indicator lights

Once the desired wash cycle has been selected and

has begun, the indicator lights switch on one by one

to indicate which phase of the cycle is currently in

progress.

Function buttons and corresponding indicator

lights

When a function is selected, the corresponding

indicator light will illuminate.

If the selected function is not compatible with the

programmed wash cycle, the corresponding indicator

light will flash and the function will not be activated.

If the selected function is not compatible with another

function which has been selected previously, the

indicator light corresponding to the first function

selected will flash and only the second function will be

activated; the indicator light corresponding to the

enabled option will remain lit.

Door locked indicator light

When the indicator light is on, the porthole door is

locked to prevent it from being opened; make sure

the indicator light is off before opening the door (wait

approximately 3 minutes). To open the door during a

running wash cycle, press the START/PAUSE button;

the door may be opened once the DOOR LOCKED

indicator light turns off.

Starting a wash cycle

1. Switch the washing machine on by pressing the ON/OFF button. All indicator lights will switch on for a few

seconds, then they will switch off and the START/PAUSE indicator light will pulse.

2. Load the laundry and close the door.

3. Set the WASH CYCLE knob to the desired programme.

4. Set the washing temperature (see Personalisation).

5. Set the spin speed (see Personalisation).

6. Measure out the detergent and washing additives (see Detergents and laundry).

7. Select the desired functions.

8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit

in a fixed manner, in green.

To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.

9. At the end of the wash cycle the

indicator light will switch on. The door can be opened once the DOOR

LOCK

indicator light turns off. Take out your laundry and leave the appliance door ajar to make sure the drum

dries completely. Switch the washing machine off by pressing the ON/OFF button.

Wash

Rinse

Spin

Drain

End of wash cycle

Specials wash cycles

Express (wash cycle 10) this wash cycle was designed to wash lightly soiled garments quickly: it lasts just 15 minutes

and therefore saves both energy and time. By selecting this wash cycle (10 at 30°C), it is possible to wash different

fabrics together (except for wool and silk items), with a maximum load of 1.5 kg.

Sport Intensive (wash cycle 11) is for washing heavily soiled sports clothing fabrics (tracksuits, shorts, etc.); for

best results, we recommend not exceeding the maximum load indicated in the

"Table of wash cycles"

Sport Light (wash cycle 12) is for washing lightly soiled sports clothing fabrics (tracksuits, shorts, etc.); for best

results, we recommend not exceeding the maximum load indicated in the

"Table of wash cycles"

. We recommend

using a liquid detergent and dosage suitable for a half-load.

Sport Shoes (wash cycle 13) is for washing sports shoes; for best results, do not wash more than 2 pairs

simultaneously.

Wash cycles

The information contained in the table is intended as a guide only.

For all Test Institutes:

1) Test wash cycle in compliance with regulation EN 60456: set wash cycle 2 with a temperature of 60°C.

2) Long wash cycle for cottons: set wash cycle 2 with a temperature of 40°C.

3) Short wash cycle for cottons: set wash cycle 4 with a temperature of 40°C.

Wash cycles

Table of wash cycles

Description of the wash cycle

Max

temp.

(°C)

Max.

speed

(rpm)

Detergents

Max. load

(kg)

Cycle

duration

Prewash Wash Bleach

Fabric

softener

Normal

Eco

Time

Daily

Cotton with prewash:

extremely soiled whites.

90° 800

Cotton:

extremely soiled whites.

90° 800

ll l

Cotton (1):

heavily soiled whites and resistant colours.

60° 800

ll l

Cotton (2):

heavily soiled whites and delicate colours.

40° 800

ll l

Cotton:

heavily soiled whites and resistant colours.

60° 800

ll l

63,25

Coloured Cottons (3):

lightly soiled whites and delicate colours.

40° 800

ll l

63,25

Synthetics:

heavily soiled resistant colours.

60° 800

ll l

2,5 2

Synthetics:

lightly soiled resistant colours.

40° 800

ll l

2,5 2

Special

Wool:

for wool, cashmere, etc.

40° 600

1,5

Silk/Curtains:

for garments in silk and viscose, lingerie.

30° 0

Jeans

40° 800

Express:

to refresh lightly soiled garments quickly (not suitable for

wool, silk and clothes which require washing by hand).

30° 800

1,5

Sport

Sport Intensive

30° 600

Sport Light

30° 600

Sport Shoes

30° 600

Max. 2

pairs

Partial wash cycles

Rinse

800

- -

Spin

800

- - - -

Drain

- - - -

The duration of the wash cycles can be checked on the display.

Setting the temperature

Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles).

The temperature may be lowered, or even set to a cold wash

The washing machine will automatically prevent you from selecting a temperature which is higher than the

maximum value set for each wash cycle.

Setting the spin speed

Turn the SPIN SPEED knob to set the spin speed for the selected wash cycle.

The maximum spin speeds available for each wash cycle are as follows:

Wash cycles Maximum spin speed

Cottons 800 rpm

Synthetics 800 rpm

Wool 600 rpm

Silk drain only

The spin speed may be lowered, or the spin cycle can be excluded altogether by selecting the symbol

The washing machine will automatically prevent you from selecting a spin speed which is higher than the

maximum speed set for each wash cycle.

Functions

The various wash functions available with this washing machine will help to achieve the desired results, every time.

To activate the functions:

1. Press the button corresponding to the desired function;

2. the function is enabled when the corresponding indicator light is illuminated.

Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in

conjunction with the selected wash cycle.

Delay timer

To set a delayed start for the selected programme, press the corresponding button repeatedly until the required

delay period has been reached. When this option is enabled, the

symbol lights up on the display. To remove the

delayed start option press the button until the text "OFF" appears on the display.

 This option is enabled with all programmes.

Selecting this option enables you to suitably adjust drum rotation, temperature and water to a reduced load of

lightly soiled cotton and synthetic fabrics (refer to the "

"Table of wash cycles"

).   enables you to wash in

less time thereby saving water and electricity. We suggest using a liquid detergent suitably measured out to the

load quantity.

 This function may not be used in conjunction with wash cycles 1, 2, 7, 8, 9, 10, 11, 12, 13, , , .

Stain removal

Bleaching cycle designed to remove the toughest stains. Please remember to pour the bleach into extra

compartment 4 (see Bleach cycle).

 This function may not be used in conjunction with wash cycles 1, 7, 8, 9, 10, 11, 12, 13, , .

Personalisation

Detergents and laundry

Detergent dispenser drawer

Good washing results also depend on the correct

dose of detergent: adding too much detergent will not

necessarily result in a more efficient wash, and may in

fact cause build up on the inside of your appliance

and contribute to environmental pollution.

 Do not use hand washing detergents because these

create too much foam.

Open the detergent

dispenser drawer and

pour in the detergent or

washing additive, as

follows.

ompartment 1: Pre-wash detergent (powder)

Before pouring in the detergent, make sure that extra

compartment 4 has been removed.

compartment 2: Detergent for the wash cycle

(powder or liquid)

Liquid detergent should only be poured in immediately

prior to the start of the wash cycle.

compartment 3: Additives (fabric softeners, etc.)

The fabric softener should not overflow the grid.

extra compartment 4: Bleach

Bleach cycle

 Traditional bleach should be used on sturdy white

fabrics, and delicate bleach for coloured fabrics,

synthetics and for wool.

This option is particularly

useful for the removal of

stubborn stains. Place

extra compartment 4

(supplied) into

compartment 1.

When pouring in the

bleach, be careful not to

exceed the "max" level

marked on the central

pivot (see figure).

To run the bleach cycle on its own, pour the bleach into

extra compartment 4, set the "Rinse"

programme

and activate the "Stain removal"

option.

To bleach during a wash cycle, pour in the detergent

and any fabric softener you wish to use, set the desired

wash cycle and enable the "Stain removal"

option.

The use of extra compartment 4 excludes the Pre-

wash option.

Preparing the laundry

 Divide the laundry according to:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from

whites.

 Empty all garment pockets and check the buttons.

 Do not exceed the listed values, which refer to the

weight of the laundry when dry:

Durable fabrics: max. 6 kg

Synthetic fabrics: max. 2,5 kg

Delicate fabrics: max. 2 kg

Wool: max. 1,5 kg

Silk: max. 1 kg

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1200 g

1 towel 150-250 g

Garments requiring special care

Wool: all wool garments can be washed using

programme 7, even those carrying the "hand-wash

only"

label. For best results, use special

detergents and do not exceed 1,5 kg of laundry.

Silk: use special wash cycle 8 to wash all silk

garments. We recommend the use of special

detergent which has been designed to wash delicate

clothes.

Curtains: fold curtains and place them in a pillow

case or mesh bag. Use wash cycle 8.

Jeans: Turn garments inside-out before washing and

use a liquid detergent. Use programme 9.

Load balancing system

Before every spin cycle, to avoid excessive vibrations

and to distribute the load in a uniform manner, the

drum rotates continuously at a speed which is slightly

greater than the washing rotation speed. If, after

several attempts, the load is not balanced correctly,

the machine spins at a reduced spin speed. If the

load is excessively unbalanced, the washing machine

performs the distribution process instead of spinning.

To encourage improved load distribution and balance,

we recommend small and large garments are mixed

in the load.

Precautions and tips

 This washing machine was designed and

constructed in accordance with international safety

regulations. The following information is provided for

safety reasons and must therefore be read carefully.

General safety

 This appliance was designed for domestic use only.

 The washing machine must only be used by adults, in

accordance with the instructions provided in this manual.

 Do not touch the machine when barefoot or with

wet or damp hands or feet.

 Do not pull on the power supply cable when

unplugging the appliance from the electricity

socket. Hold the plug and pull.

 Do not open the detergent dispenser drawer while

the machine is in operation.

 Do not touch the drained water as it may reach

extremely high temperatures.

 Never force the porthole door. This could damage

the safety lock mechanism designed to prevent

accidental opening.

 If the appliance breaks down, do not under any

circumstances access the internal mechanisms in

an attempt to repair it yourself.

 Always keep children well away from the appliance

while it is operating.

 The door can become quite hot during the wash cycle.

 If the appliance has to be moved, work in a group

of two or three people and handle it with the utmost

care. Never try to do this alone, because the

appliance is very heavy.

 Before loading laundry into the washing machine,

make sure the drum is empty.

Disposal

 Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

 The European Directive 2002/96/EC on Waste

Electrical and Electronic Equipment, requires that

old household electrical appliances must not be

disposed of in the normal unsorted municipal waste

stream. Old appliances must be collected

separately in order to optimise the recovery and

recycling of the materials they contain and reduce

the impact on human health and the environment.

The crossed out "wheeled bin" symbol on the

product reminds you of your obligation, that when

you dispose of the appliance it must be separately

collected.

Consumers should contact their local authority or

retailer for information concerning the correct

disposal of their old appliance.

Care and maintenance

Cutting off the water and electricity

supplies

 Turn off the water tap after every wash cycle. This

will limit wear on the hydraulic system inside the

washing machine and help to prevent leaks.

 Unplug the washing machine when cleaning it and

during all maintenance work.

Cleaning the washing machine

The outer parts and rubber components of the

appliance can be cleaned using a soft cloth soaked

in lukewarm soapy water. Do not use solvents or

abrasives.

Cleaning the detergent dispenser

drawer

Remove the dispenser

by raising it and pulling it

out (see figure).

Wash it under running

water; this operation

should be repeated

frequently.

Caring for the door and drum of your

appliance

 Always leave the porthole door ajar in order to

prevent unpleasant odours from forming.

Cleaning the pump

The washing machine is fitted with a self-cleaning

pump which does not require any maintenance.

Sometimes, small items (such as coins or buttons)

may fall into the pre-chamber which protects the

pump, situated in its bottom part.

 Make sure the wash cycle has finished and unplug

the appliance.

To access the pre-chamber:

1. using a screwdriver,

remove the cover panel

on the lower front part of

the washing machine

(see figure);

2. unscrew the lid by

rotating it anti-clockwise

(see figure): a little water

may trickle out. This is

perfectly normal;

3. clean the inside thoroughly;

4. screw the lid back on;

5. reposition the panel, making sure the hooks are

securely in place before you push it onto the

appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If there are

any cracks, it should be replaced immediately: during

the wash cycles, water pressure is very strong and a

cracked hose could easily split open.

 Never use second-hand hoses.

Troubleshooting

Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see Assistance),

make sure that the problem cannot be not solved easily using the following list.

Problem:

The washing machine does not

switch on.

The wash cycle does not start.

The washing machine does not

take in water ("H2O" will flash

on the display).

The washing machine

continuously takes in and drains

water.

The washing machine does not

drain or spin.

The washing machine vibrates a

lot during the spin cycle.

The washing machine leaks.

The "function" indicator lights and

the "start/pause" indicator light

flash, while one of the "phase in

progress" indicator lights and the

"door locked" indicator light will

remain lit in a fixed manner.

There is too much foam.

Possible causes / Solutions:

 The appliance is not plugged into the socket fully, or is not making contact.

 There is no power in the house.

 The washing machine door is not closed properly.

 The ON/OFF button has not been pressed.

 The START/PAUSE button has not been pressed.

 The water tap has not been opened.

 A delayed start has been set (see Personalisation).

 The water inlet hose is not connected to the tap.

 The hose is bent.

 The water tap has not been opened.

 There is no water supply in the house.

 The pressure is too low.

 The START/PAUSE button has not been pressed.

 The drain hose is not fitted at a height between 65 and 100 cm from

the floor (see Installation).

 The free end of the hose is under water (see Installation).

 The wall drainage system is not fitted with a breather pipe.

If the problem persists even after these checks, turn off the water tap,

switch the appliance off and contact the Assistance Service. If the

dwelling is on one of the upper floors of a building, there may be problems

relating to water drainage, causing the washing machine to fill with water

and drain continuously. Special anti-draining valves are available in shops

and help to avoid this inconvenience.

 The wash cycle does not include draining: some wash cycles require

the drain phase to be started manually.

 The drain hose is bent (see Installation).

 The drainage duct is clogged.

 The drum was not unlocked correctly during installation (see Installation).

 The washing machine is not level (see Installation).

 The washing machine is trapped between cabinets and walls (see Installation).

 The water inlet hose is not screwed on properly (see Installation).

 The detergent dispenser drawer is blocked (for cleaning instructions, see

Care and maintenance).

 The drain hose is not fixed properly (see Installation).

 Switch off the machine and unplug it, wait for approximately 1 minute

and then switch it back on again.

If the problem persists, contact the Technical Assistance Service.

 The detergent is not suitable for machine washing (it should display the

text for washing machines or hand and machine wash, or the like).

 Too much detergent was used.

Service

Before calling for Assistance:

 Check whether you can solve the problem alone (see Troubleshooting);

 Restart the programme to check whether the problem has been solved;

 If this is not the case, contact an authorised Technical Assistance Centre using the telephone number

provided on the guarantee certificate.

 Always request the assistance of authorised technicians.

Have the following information to hand:

 the type of problem;

 the appliance model (Mod.);

 the serial number (S/N).

This information can be found on the data plate applied to the rear of the washing machine, and can also

be found on the front of the appliance by opening the door.

Românã

Sumar

Instalare, 14-15

Despachetare ºi punere la nivel

Racorduri hidraulice ºi electrice

Primul ciclu de spãlare

Date tehnice

Descrierea maºinii de spãlat ºi activarea

unui program, 16-17

Panoul de control

Indicatoare luminoase

Activarea unui program

Programe, 18

Tabel de programe

Personalizare, 19

Reglarea temperaturii

Reglarea centrifugãrii

Funcþii

Detergenþi ºi rufe albe, 20

Compartimentul pentru detergenþi

Ciclu de albire

Pregãtirea rufelor

Articole delicate

Sistemul de echilibrare a încãrcãturii

Precauþii ºi sfaturi, 21

Norme de protecþie ºi siguranþã generale

Aruncarea reziduurilor

Întreþinere ºi curãþare, 22

Întreruperea alimentãrii cu apã ºi curent electric

Curãþarea maºinii de spãlat

Curãþarea compartimentului pentru detergent

Îngrijirea uºii ºi a tamburului

Curãþarea pompei

Controlarea furtunului de alimentare cu apã

Anomalii ºi remedii, 23

Asistenþã, 24

IWD 6085

Instrucþiuni de folosire

MAªINÃ DE SPÃLAT RUFE

Instalare

 Este important sã pãstraþi acest manual pentru a-l

putea consulta în orice moment. În caz de vânzare,

de cesiune sau de schimbare a locuinþei, acesta

trebuie sã rãmânã împreunã cu maºina de spãlat

pentru a informa noul proprietar cu privire la

funcþionare ºi la respectivele avertismente.

 Citiþi cu atenþie instrucþiunile: veþi gãsi informaþii

importante cu privire la instalare, la folosire ºi la

siguranþã.

Despachetare ºi punere la nivel

Despachetare

1. Scoaterea din ambalaj a maºinii de spãlat.

2. Controlaþi ca maºina de spãlat sã nu fi fost

deterioratã în timpul transportului. Dacã este

deterioratã nu o conectaþi ºi luaþi legãtura cu

vânzãtorul.

3. Scoateþi cele !

ºuruburi de protecþie

pentru transport ºi

cauciucul cu respectivul

distanþier, situate în

partea posterioarã

(a se vedea figura).

4. Închideþi orificiile cu dopurile din plastic aflate în

dotare.

5. Pãstraþi toate piesele: pentru cazul în care

maºina de spãlat va trebui sã fie transportatã,

piesele vor trebui montante din nou.

 Ambalajele nu sunt jucãrii pentru copii!

Punere la nivel

1. Instalaþi maºina de spãlat pe o suprafaþã planã ºi

rigidã, fãrã a o sprijini de ziduri, mobilã sau altceva.

2. Dacã podeaua nu este

perfect orizontalã,

compensaþi

neregularitãþile

deºurubând sau

înºurubând picioruºele

anterioare (a se vedea

figura); unghiul de

înclinare, mãsurat pe

planul de lucru, nu trebuie

sã depãºeascã 2°.

O nivelare precisã conferã stabilitate maºinii ºi evitã

vibraþii, zgomote ºi deplasãri pe timpul funcþionãrii.

În cazul mochetelor sau a unui covor, reglaþi

picioruºele astfel încât sã menþineþi sub maºina de

spãlat un spaþiu suficient pentru ventilare.

Racorduri hidraulice ºi electrice

Racordarea furtunului de alimentare cu apã

1. Conectaþi tubul de

alimentare, înºurubându-l

la un robinet de apã rece

cu gura filetatã de 3/4

gaz (a se vedea figura).

Înainte de conectare,

lãsaþi apa sã curgã pânã

când nu a devine

limpede.

2. Conectaþi tubul de

alimentare la maºina de

spãlat, înºurubându-l la

sursa de apã respectivã,

amplasatã în partea

posterioarã, sus în

dreapta (a se vedea

figura).

3. Fiþi atenþi ca furtunul sã nu fie nici pliat nici îndoit.

 Presiunea apei de la robinet trebuie sã fie cuprinsã

în valorile din tabelul Date tehnice (a se vedea

pagina alãturatã).

 Dacã lungimea furtunului de alimentare nu este

suficientã, adresaþi-vã unui magazin specializat sau

unui instalator autorizat.

 Nu folosiþi niciodatã tuburi folosite deja.

 Utilizaþi tuburile furnizate împreunã cu maºina.

65 - 100 cm

Conectarea furtunului de golire

Conectaþi furtunul de

golire - fãrã a-l îndoi - la

canalizare sau la

racordul de golire

prevãzut pe perete, la o

înãlþime de 65 - 100 cm

de sol;

Sprijiniþi-l de marginea

cãzii sau chiuvetei ºi

racordaþi ºina de ghidare

din dotare la robinet (a

se vedea figura).

Capãtul liber al

furtunului de golire nu

trebuie sã rãmânã

cufundat în apã.

 Nu se recomandã folosirea furtunurilor

prelungitoare; dacã este indispensabil, acestea

trebuie sã aibã acelaºi diametru ca ºi furtunul

original ºi nu trebuie sã depãºeascã 150 cm

lungime.

Racordarea electricã

Înainte de a introduce stecherul în prizã, asiguraþi-vã ca:

 priza sã fie cu împãmântare ºi conform

prevederilor legale;

 priza sã poatã suporta sarcina maximã de putere

a maºinii, indicatã în tabelul Date Tehnice

(a se vedea alãturi);

 tensiunea de alimentare sã fie cuprinsã în valorile

indicate în tabelul Date Tehnice (a se vedea

alãturi);

 priza sã fie compatibilã cu stecherul maºinii de

spãlat. În caz contrar înlocuiþi stecherul.

 Maºina de spãlat nu trebuie instalatã afarã, nici

chiar în cazul în care spaþiul este adãpostit,

deoarece este foarte periculoasã expunerea maºinii

la ploi ºi furtuni.

 Dupã instalarea maºinii de spãlat, priza de curent

trebuie sã fie uºor accesibilã.

 Nu folosiþi prelungitoare ºi prize multiple.

 Cablul nu trebuie sã fie îndoit sau comprimat.

 Cablul de alimentare trebuie sã fie înlocuit doar de

tehnicieni autorizaþi ai centrului de service ce apare

scris pe certificatul de garantie emis de producator.

Atenþie! Producãtorul îºi declinã orice

responsabilitate în cazul în care aceste norme nu se

respectã.

Primul ciclu de spãlare

Dupã instalare, înainte de folosire, efectuaþi un ciclu

de spãlare cu detergent ºi fãrã rufe, selectând

programul 2.

Date tehnice

Model

IWD 6085

Dimensiuni

lãrgime: 59,5 cm

înãlþime: 85 cm

profunzime: 52,5 cm

Capacitate

de la 1 la 6 kg

Legãturi electrice

vezi eticheta cu caracteristicile tehnice,

aplicatã pe maºinã

Legãturi hidrice

presiune maximã: 1 MPa (10 bari)

presiune minimã: 0,05 MPa (0,5 bari)

capacitatea cuvei: 46 litri

Turaþia de

centrifugare

pânã la 1200 de rotaþii pe minut

Programe de control

în baza normei

EN 60456

programul 2; temperatura 60°

efectuatã cu 6 kg de rufe.

Acest aparat este conform cu

urmãtoarele Directive Comunitare:

- 89/336/CEE din data de 03/05/89

(Compatibilitate Electromagneticã) ºi

modificãri succesive

- 2002/96/CE

- 2006/95/CE (Tensiuni Joase)

Zgomot

(dB(A) re 1 pW)

Spãlare: 66

Turaþie de centrifugare: 73

Sertarul detergenþilor: pentru a introduce

detergenþi sau aditivi (a se vedea Detergenþi ºi rufe

albe).

Tasta PORNIRE/OPRIRE: pentru a porni ºi opri

maºina.

Selector PROGRAME: pentru a selecta programele.

Pe durata desfãºurãrii programului selectorul rãmâne

în aceeaºi poziþie.

Taste cu led FUNCÞII: pentru a selecta funcþiile

disponibile. Indicatorul corespunzãtor funcþiei alese

va rãmâne aprins.

Selector CENTRIFUGARE: pentru a activa / anula

centrifugarea (a se vedea Personalizare).

Selector TEMPERATURÃ: pentru a selecta temperatu-

ra sau spãlarea la rece (a se vedea Personalizare).

DISPLAY: pentru a afiºa durata diferitelor programe

la dispoziþie ºi a celui restant, în cazul unui ciclu de

spãlare deja în desfãºurare; dacã a fost programat

un interval de PORNIRE ÎNTÂRZIATÃ, este afiºat

intervalul restant pânã la pornirea programului

selectat.

Tastã PORNIRE ÎNTÂRZIATÃ

: apãsaþi pentru a

programa pornirea maºinii la o anumitã orã.

Întârzierea va fi indicatã pe display.

Indicatoare DESFÃªURARE CICLU: pentru a putea

urmãri avansarea programului de spãlare.

Indicatorul aprins aratã faza în curs de desfãºurare.

Indicator UªÃ BLOCATÃ: pentru a înþelege dacã uºa

se poate deschide sau nu (a se vedea pag. alãturatã).

Tastã cu led START/PAUZÃ: pentru a activa / opri

momentan programele.

N.B.: pentru a întrerupe momentan un ciclu apãsaþi

aceastã tastã; ledul se va aprinde intermitent

(culoare portocalie) în timp ce ledul corespunzãtor

fazei în curs de desfãºurare va rãmâne aprins. Dacã

indicatorul UªÃ BLOCATÃ

este stins, atunci uºa

se poate deschide.

Pentru a continua spãlarea, de unde a fost

întreruptã, apãsaþi din nou tasta.

Modalitatea de stand by

Aceastã maºinã de spãlat rufe, conform noilor

norme legate de economia de curent electric, este

dotatã cu un sistem de oprire automat (stand-by)

care intrã în funcþiune dupã câteva minute de

neutilizare. Apãsaþi scurt tasta PORNIRE/OPRIRE

ºi aºteptaþi repunerea în funcþiune a maºinii.

Descrierea maºinii de spãlat ºi

activarea unui program

Indicator

UªÃ BLOCATÃ

Tastã cu led

START/

PAUZÃ

Panoul de control

Sertarul detergenþilor

Tasta

PORNIRE/OPRIRE

Selector

PROGRAME

Selector

TEMPERATURÃ

Selector

CENTRIFUGARE

Taste cu led

FUNCÞII

Indicatoare

DESFÃªURARE CICLU

DISPLAY

Tastã

PORNIRE

ÎNTÂRZIATÃ

Indicatoare luminoase

Ledurile furnizeazã informaþii importante.

Iatã ce indicã:

Indicatoare de fazã

Dupã alegerea ºi activarea ciclului dorit,

indicatoarele luminoase se vor aprinde unul dupã

altul, ceea ce vã indicã starea de avansare a

programului:

Tastele de funcþii ºi ledurile corespunzãtoare

Alegerea unei funcþii implicã aprinderea ledului

corespunzãtor.

Dacã funcþia selectatã nu este compatibilã cu

programul ales, ledul corespunzãtor se va aprinde

intermitent iar funcþia nu se va activa.

Dacã funcþia aleasã nu este compatibilã cu o funcþie

selectatã anterior, indicatorul care corespunde

primei funcþii va emite un semnal intermitent iar

indicatorul celei de a doua se va aprinde: acest lucru

înseamnã cã se va activa numai a doua funcþie

(ultima aleasã).

Indicator uºã blocatã:

Aprinderea ledului indicã faptul cã hubloul s-a

blocat, pentru a împiedica deschiderea sa; pentru a

putea deschide hubloul, aºteptaþi aproximativ 3

minute, pânã la stingerea ledului. Pentru a deschide

hubloul în timpul executãrii unui ciclu, apãsaþi tasta

PORNIRE/PAUZÃ; dacã ledul UªÃ BLOCATÃ este

stins, atunci puteþi deschide hubloul.

Activarea unui program

1. Porniþi maºina de spãlat apãsând pe tasta PORNIRE/OPRIRE. Toate indicatoarele se aprind câteva secunde,

apoi se sting; indicatorul START/PAUZÃ se va aprinde intermitent.

2. Introduceþi rufele ºi închideþi uºa.

3. Selectaþi programul dorit cu ajutorul selectorului de PROGRAME.

4. Reglaþi temperatura de spãlare (a se vedea Personalizare).

5. Reglaþi viteza de centrifugare (a se vedea Personalizare).

6. Adãugaþi detergentul ºi aditivii (a se vedea Detergenþi ºi rufe).

7. Alegeþi funcþiile dorite.

8. Activaþi programul apãsând tasta START/PAUZÃ; indicatorul luminos se va aprinde (culoare verde).

Pentru a anula un ciclu selectat, apãsaþi tasta START/PAUZÃ pentru a întrerupe momentan ciclul ºi alegeþi un

nou program.

9. La încheierea programului, indicatorul luminos

se va aprinde. Dupã stingerea ledului corespunzãtor avertizãrii

de UªÃ BLOCATA

, este posibilã deschiderea hubloului. Scoateþi rufele ºi lãsaþi uºa întredeschisã pentru a se

putea usca cuva si tamburul. Opriti maºina de spãlat apãsând pe tasta PORNIRE/OPRIRE.

Spãlare

Clãtire

Centrifugã

Golire

Sfârºit Spãlare

Programe speciale

Express (programul 10) a fost studiat pentru a spãla articolele foarte puþin murdare, în mod rapid: dureazã doar

15 de minute ceea ce economiseºte energie ºi timp. Selectând programul (10 la 30°C) este posibilã spãlarea

articolelor din materiale diferite (excluse lâna ºi mãtasea) cu o greutate maximã de 1,5 kg.

Sport Intensive (programul 11) a fost studiat pentru spãlarea þesãturilor utilizate la confecþionarea hainelor

sportive (echipamente, pantaloni scurþi etc.) foarte murdare; pentru cele mai bune rezultate, se recomandã sã

nu depãºiþi cantitatea maximã admisã indicatã în Tabel de programe.

Sport Light (programul 12) a fost studiat pentru spãlarea þesãturilor utilizate la confecþionarea hainelor sportive

(echipamente, pantaloni scurþi etc.) puþin murdare; pentru cele mai bune rezultate, se recomandã sã nu depãºiþi

cantitatea maximã admisã indicatã în Tabel de programe. Se recomandã utilizarea detergentului lichid într-o

cantitate adecvatã unei încãrcãri pe jumãtate a maºinii.

Sport Shoes (programul 13) a fost studiat pentru spãlarea pantofilor de sport; pentru cele mai bune rezultate,

nu spãlaþi mai mult de 2 perechi deodatã.

Programe

Datele specificate în tabel au valoare indicativã.

Pentru toate Instituþiile de Testare:

1) Programul de control conform normei EN60456: selectaþi programul 2 ºi temperatura de 60°C.

2) Program pentru bumbac, prelungit: selectaþi programul 2 ºi temperatura de 40°C.

3) Program

pentru

bumbac, rapid: selectaþi programul 4 ºi temperatura de 40°C.

Tabel de programe

Programe

Descrierea Programului

Te mp .

max.

(°C)

Viteza

max.

(rotaþii pe

minut)

Detergenþi

Sarcina Max.

(Kg)

Durata

ciclului de

spãlare

Pres-

pãlare

Spãlare

Decolo-

rant

Balsam

rufe

Normalã

Eco

Time

Programe zilnice

PRESPALARE BUMBAC:

Rufe albe foarte murdare.

90°

800

RUFE ALBE BUMBAC:



Rufe albe foarte murdare.

90°

800

ll l

RUFE ALBE BUMBAC (1):

Albe ºi colorate rezistente foarte murdare.

60°

800

ll l

RUFE ALBE BUMBAC (2):



Albe ºi colorate delicate foarte murdare.

40°

800

ll l

RUFE ALBE BUMBAC:

Albe ºi colorate rezistente foarte murdare.

60°

800

ll l

63,25

COLORATE BUMBAC (3):

Albe puþin murdare ºi colorate delicate.

40°

800

ll l

63,25

SINTETICE:

Colorate rezistente foarte murdare.

60°

800

ll l

2,5 2

SINTETICE:

Colorate delicate putin murdare.

40°

800

ll l

2,5 2

Programe Speciale

LÂNÃ:

Pentru articole din lânã, caºmir.

40°

600

1,5

MÃTASE /PERDELE:

Pentru articolele din mãtase, viscozã, lenjerie.

30°

JEANS

40°

800

EXPRESS:

Pentru a împrospãta rapid articolele puþin murdare (nu este

indicat pentru lânã, mãtase ºi articole de spãlat cu mâna).

30°

800

1,5

Sport

Sport Intensive

30°

600

Sport Light

30°

600

Sport Shoes

30°

600

(

Max 2

perechi.)

Programe parþiale

CLÃTIRE

800

- -

CENTRIFUGARE

800

- - - -

EVACUARE

- - - -

Puteþi vizualiza durata programelor de spãlare pe display.

Reglarea temperaturii

Rotind selectorul de TEMPERATURÃ se fixeazã temperatura de spãlare (a se vedea Tabelul programelor).

Temperatura poate fi redusã pânã la spãlarea la rece (

Maºina va împiedica în mod automat de a alege o temperaturã mai mare decât maxima admisã pentru fiecare program.

Reglarea centrifugãrii

Rotind selectorul de CENTRIFUGARE se stabileºte viteza de stoarcere pentru programul selectat.

Vitezele maxime, prevãzute pentru programe sunt:

Programe Vitezã maximã

Bumbac 800 rotaþii pe minut

Sintetice 800 rotaþii pe minut

Lânã 600 rotaþii pe minut

Mãtase excludere stoarcere

Viteza de centrifugaare poate fi redusã sau centrifugarea poate fi exclusã selectând simbolul

Maºina va împiedica în mod automat alegerea unei viteze mai mari decât maxima admisã pentru fiecare

program.

Funcþii

Diferitele funcþii de spãlare prevãzute pentru maºina de spãlat, permit obþinerea unor rufe curate ºi albe, dupã

dorinþã.

Pentru a activa funcþiile:

1. apãsaþi tasta corespunzãtoare funcþiei dorite;

2. aprinderea ledului respectiv indicã activarea funcþiei.

Notã: Semnalul luminos intermitent, rapid, indicã faptul cã funcþia respectivã nu este compatibilã cu programul

ales.

Pornirea întârziatã

Pentru a programa pornirea întârziatã a maºinii, apãsaþi tasta respectivã pentru a alege timpul de întârziere dorit.

Când opþiunea este activã, pe ecran se va aprinde simbolul . Pentru a anula pornirea întârziatã, apãsaþi tasta pânã

când pe ecran veþi vedea mesajul OFF.

 Se poate activa pe toate programele.

Prin selectarea acestei opþiuni, miºcarea mecanicã, temperatura ºi apa sunt optimizate pentru o cantitate

scãzutã de þesãturi de bumbac ºi sintetice puþin murdare Tabel de programe. Cu 

 puteþi spãla în timp

mai scurt, economisind apã ºi energie. Se recomandã utilizarea unei cantitãþi de detergent lichid adecvatã

cantitãþii de rufe.

 Nu poate fi activatã pe programele 1, 2, 7, 8, 9, 10, 11, 12, 13, , , .

Antipatã

Ciclu de decolorare adecvat pentru eliminarea petelor mai rezistente. A se vãrsa decolorantul în sertarul

adiþional 4 (a se vedea Ciclu de albire).

 Nu se poate activa pe programele 1, 7, 8, 9, 10, 11, 12, 13, , .

Personalizare

Detergenþi ºi rufe albe

Compartimentul pentru detergenþi

Un rezultat bun la spãlare depinde ºi de dozarea

corectã a detergentului: excesul de detergent nu

garanteazã o spãlare mai eficientã, ci contribuie la

deteriorarea pãrþilor interne ale maºinii de spãlat ºi

la poluarea mediului înconjurãtor.

 Nu introduceþi în maºinã detergenþii pentru

spãlarea manualã deoarece formeazã prea multã

spumã.

Deschideþi

compartimentul pentru

detergenþi ºi introduceþi

detergentul sau aditivul

dupã cum urmeazã:

compartiment 1: Detergent pentru prespãlare

(sub formã de praf)

Înainte de a adãuga detergentul verificaþi ca sertarul

adiþional 4 sã nu fie introdus.

compartiment 2: Detergent pentru spãlare

(sub formã de praf sau lichid)

Detergentul lichid trebuie vãrsat doar înainte de pornire.

compartiment 3: Aditivi

(soluþie de înmuiat, balsam rufe etc.)

Soluþia de înmuiat nu trebuie sã iasã deasupra

grãtarului.

compartiment adiþional 4: Decolorant (Inãlbitor)

Ciclu de albire

 Decolorantul tradiþional se foloseºte pentru

þesãturi rezistente albe, cel delicat pentru þesãturi

colorate, sintetice ºi pentru lânã.

Introduceþi sertarul adiþional 4, aflat în dotare, în

sertarul 1.

Când dozaþi decolorantul

nu depãºiþi nivelul max

indicat pe pivotul central

(vezi figura).

Pentru efectuarea doar a

decolorãrii, vãrsaþi

decolorantul în sertarul

adiþional 4, selectaþi programul Clãtire

ºi activaþi

opþiunea Antipatã

Pentru albirea în timpul spãlãrii, vãrsaþi detergentul

ºi aditivii, selectaþi programul dorit ºi activaþi

opþiunea Antipatã

Folosirea sertarului adiþional 4 exclude prespãlarea.

Pregãtirea rufelor

 Sortaþi rufele în funcþie de:

- tipul de material / simbolul de pe etichetã.

- culori: separaþi rufele colorate de cele albe.

 Goliþi buzunarele ºi controlaþi nasturii.

 Nu depãºiþi valorile indicate, referitoare la

greutatea rufelor uscate:

Þesãturi rezistente: max 6 kg

Materiale sintetice: max 2,5 kg

Þesãturi delicate: max 2 kg

Lânã: max 1,5 kg

Mãtase: max 1 kg

Cât cântãresc rufele?

1 cearceaf 400-500 g.

1 faþã de pernã 150-200 g.

1 faþã de masã 400-500 g.

1 halat de baie 900-1.200 g.

1 prosop 150-250 g.

Articole delicate

Lânã: Cu programul 7 se pot spãla cu maºina toate

hainele de lânã, inclusiv cele cu eticheta a se spãla

numai manual

. Pentru a obþine cele mai bune

rezultate, folosiþi un detergent specific ºi nu depãºiþi

1,5 kg de rufe.

Mãtase: utilizaþi programul special 8 pentru spãlarea

articolelor din mãtase. Se recomandã folosirea unui

detergent special pentru articole delicate.

Perdele:

împãturiþi-le ºi aºezaþi-le într-o faþã de pernã

sau într-un sac de tip plasã. Utilizaþi programul 8.

Jeans: întoarceþi pe dos rufele înainte de spãlare ºi

utilizaþi un detergent lichid. Utilizaþi programul 9.

Sistemul de echilibrare a încãrcãturii

Pentru a evita trepidaþiile excesive, înainte de

stoarcere, cuva maºinii va distribui cantitatea de rufe

în mod uniform, centrifuga efectuând câteva rotaþii la

o vitezã mai mare decât viteza de spãlare. Dacã,

dupã numeroase încercãri, maºina nu reuºeºte sã

echilibreze greutatea, stoarcerea rufelor se va face

la o vitezã mai micã decât cea prevãzutã în program.

Dacã instabilitatea este prea mare, maºina va

distribui greutatea în locul centrifugei. Pentru a

favoriza o mai bunã repartizare a rufelor ºi

echilibrarea corectã a maºinii, se recomandã sã

introduceþi în maºinã atât articole mari cât ºi mici.

La pagina sta caricando ...

Whirlpool IWD 6085 (EU) Guida utente

Marca: Whirlpool

Modello: IWD 6085 (EU)

Categoria: Lavatrici

Tipo: Guida utente

Scarica il pdf

rapporto

Whirlpool IWD 6085 (EU) Guida utente

Whirlpool IWD 6085 (EU) Guida utente

in altre lingue

Documenti correlati

Altri documenti