Ubiquiti CRM Point CRM-P Quick Start Quide

Tipo
Quick Start Quide
Model: CRM-P
Introduction
Thank you for purchasing the Ubiquiti Networks®
CRMPoint
. This Quick Start Guide is designed to
guide you through installation and also includes
warrantyterms.
Package Contents
CRM Point Ethernet Cable
Model: CRM-P
microSD Card
(8 GB)
Quick Start
Guide
System Requirement
Web Browser: Mozilla Firefox, Google Chrome, or
Microsoft Internet Explorer 11 (or above)
TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above). It is
the customers responsibility to follow local country regulations, including
operation within legal frequency channels, output power, indoor cabling
requirements, and Dynamic Frequency Selection (DFS) requirements.
Hardware Overview
Front Panel LED
LED Color Status
White Factory defaults.
Alternating
White/Blue
Device is busy; do not touch or
unplug it. This usually indicates
that a process such as a firmware
upgrade is taking place.
Blue Device is working properly.
Top Panel
Ethernet Port
Ethernet This Gigabit Ethernet port is used to
connect the power and should be connected to the
LAN and DHCP server. Power can be provided by an
802.3af PoE switch, such as the Ubiquiti Networks
EdgeSwitch
.
Bottom Panel
Micro-USB Port
Reset Button
microSD Slot
Reset The Reset button serves two functions:
Restart Press and release the Reset button
quickly.
Restore to Factory Default Settings Press and
hold the Reset button for more than five seconds.
Micro-USB Optional power source (minimum
5V,1A) if PoE is not available.
microSD Insert the included microSD Card before
powering on the CRM Point.
Hardware Installation
1. Connect the Ethernet Cable to the Ethernet port.
2. Insert the included microSD Card into the
microSD Slot.
3. Connect the other end of the cable to a port on
a network switch, such as an EdgeSwitch.
24V
Powering the CRM Point
Use an 802.3af switch, such as an EdgeSwitch, or a
USB power source (not included).
EdgeSwitch
The CRMPoint can be powered by an EdgeSwitch
or other 802.3af-compliant switch.
24V
EdgeSwitch Power Connection Diagram
USB Power Source
Connect a USB cable (not included) from the
CRMPoint directly to a USB power source
(minimum 5V, 1A).
USB Power Connection Diagram
*640-00216-03*
640-00216-03
Software Installation
The CRM Control software is pre-installed on the
CRMPoint. To access it, follow these steps:
1. Ensure that your host system has an Internet
connection and is on the same Layer-2 network
as the CRMPoint.
2. The CRM Point is set to DHCP by default, so it
will try to automatically obtain an IP address.
Assign a specific IP address to the CRM Point, or
check the DHCP server to see which IP address
was assigned to it.
You can also discover the CRM Point using the
Ubiquiti® Device Discovery Tool, available at
https://www.ubnt.com/download/utilities
3. Launch a web browser. In the address field,
type http: followed by the IP address of the
CRMPoint. Press enter (PC) or return (Mac).
http://<IP_address>
4. If this is your first time using the CRMPoint,
proceed to step 5.
If you have previously logged into the
CRMPoint, proceed to step 7.
5. The CRM Point user interface will appear and
begin upgrading the device software to the
latest version.
6. When the upgrade is complete, create a new
user account:
a. Enter a Username and Password.
b. Confirm your password in the Confirm
Password field.
c. Click Create Account.
7. Enter your Username and Password, and click
Sign In to log into the CRM Point.
8. The Discovery page will appear. This page lets
you connect devices to the CRM Point. There are
two ways to connect to devices:
By IP address
By discovery (scan your network for devices)
Note: To connect a device to the CRM Point,
both must be on the same Layer-2 network.
To connect by IP address:
a. Click Search By IP.
b. Enter an IP Range with login credentials for
the devices in that range.
c. Click Connect.
To connect by discovery:
a. Click Discover to display a list of devices the
CRM Point has discovered on your network.
b. Select one or more devices that share the
same credentials.
c. Click Connect.
d. Repeat steps a to c to connect additional
devices with different login credentials.
9. When you are finished connecting devices to
the CRM Point, click Finish to display a list of
devices being monitored by the CRM Point.
You can now manage your devices using the
CRMPoint. For more information on using the
CRMPoint, visit http://crm.ubnt.com/point
Specifications
CRM-P
Dimensions 21.7 x 43.4 x 121.9 mm
(0.85 x 1.71 x 4.80")
Weight 110 g (3.88 oz)
Networking Interface (1) 10/100/1000 Ethernet Port
Buttons (1) Reset to Defaults
Power Method
PoE
Micro-USB
48V 802.3af or
Passive PoE (Pairs 4, 5+; 7, 8 Return)
5V
Power Supply 802.3af PoE or
Micro-USB 5V, 1A
Max. Power
Consumption
5W
Certications CE, FCC, IC
Operating
Temperature
0 to 40° C
(32 to 104° F)
Operating Humidity 20 to 90% Noncondensing
Safety Notices
1. Read, follow, and keep these instructions.
2. Heed all warnings.
3. Only use attachments/accessories specified by the
manufacturer.
WARNING: Do not use this product in location
that can be submerged by water.
WARNING: Avoid using this product during an
electrical storm. There may be a remote risk of
electric shock from lightning.
Electrical Safety Information
1. Compliance is required with respect to voltage, frequency,
and current requirements indicated on the manufacturers
label. Connection to a different power source than those
specified may result in improper operation, damage to
the equipment or pose a fire hazard if the limitations are
not followed.
2. There are no operator serviceable parts inside this
equipment. Service should be provided only by a
qualified service technician.
Limited Warranty
UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants
that the product(s) furnished hereunder (the “Product(s)”)
shall be free from defects in material and workmanship for a
period of one (1) year from the date of shipment by UBIQUITI
NETWORKS under normal use and operation. UBIQUITI
NETWORKS’ sole and exclusive obligation and liability under
the foregoing warranty shall be for UBIQUITI NETWORKS, at
its discretion, to repair or replace any Product that fails to
conform to the above warranty during the above warranty
period. The expense of removal and reinstallation of any
Product is not included in this warranty. The warranty period
of any repaired or replaced Product shall not extend beyond
its original term.
Warranty Conditions
The above warranty does not apply if the Product:
(I) has been modified and/or altered, or an addition
made thereto, except by Ubiquiti Networks, or
Ubiquiti Networks’ authorized representatives, or as
approved by Ubiquiti Networks in writing;
(II) has been painted, rebranded or physically modified
in any way;
(III) has been damaged due to errors or defects in cabling;
(IV) has been subjected to misuse, abuse, negligence,
abnormal physical, electromagnetic or electrical
stress, including lightning strikes, or accident;
(V) has been damaged or impaired as a result of using
third party firmware;
(VI) has no original Ubiquiti MAC label, or is missing any
other original Ubiquiti label(s); or
(VII) has not been received by Ubiquiti within 30 days of
issuance of the RMA.
In addition, the above warranty shall apply only if: the
product has been properly installed and used at all times in
accordance, and in all material respects, with the applicable
Product documentation; all Ethernet cabling runs use CAT5
(or above), and for outdoor installations, shielded Ethernet
cabling is used, and for indoor installations, indoor cabling
requirements are followed.
Returns
No Products will be accepted for replacement or repair
without obtaining a Return Materials Authorization (RMA)
number from UBIQUITI NETWORKS during the warranty
period, and the Products being received at UBIQUITI
NETWORKS’ facility freight prepaid in accordance with the
RMA process of UBIQUITI NETWORKS. Products returned
without an RMA number will not be processed and will be
returned freight collect or subject to disposal. Information on
the RMA process and obtaining an RMA number can be found
at: www.ubnt.com/support/warranty.
Disclaimer
EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN,
UBIQUITI NETWORKS, ITS AFFILIATES, AND ITS AND THEIR
THIRD PARTY DATA, SERVICE, SOFTWARE AND HARDWARE
PROVIDERS HEREBY DISCLAIM AND MAKE NO OTHER
REPRESENTATION OR WARRANTY OF ANY KIND, EXPRESS,
IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED
TO, REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF
MERCHANTABILITY, ACCURACY, QUALITY OF SERVICE OR
RESULTS, AVAILABILITY, SATISFACTORY QUALITY, LACK OF
VIRUSES, QUIET ENJOYMENT, FITNESS FOR A PARTICULAR
PURPOSE AND NON-INFRINGEMENT AND ANY WARRANTIES
ARISING FROM ANY COURSE OF DEALING, USAGE OR
TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS
AND SERVICES. BUYER ACKNOWLEDGES THAT NEITHER
UBIQUITI NETWORKS NOR ITS THIRD PARTY PROVIDERS
CONTROL BUYER’S EQUIPMENT OR THE TRANSFER OF
DATA OVER COMMUNICATIONS FACILITIES, INCLUDING THE
INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY
BE SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS,
CANCELLATIONS AND OTHER PROBLEMS INHERENT IN
THE USE OF COMMUNICATIONS FACILITIES. UBIQUITI
NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD PARTY
PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS,
DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS,
CONTENT CORRUPTION, PACKET LOSS, OR OTHER DAMAGE
RESULTING FROM ANY OF THE FOREGOING. In addition,
UBIQUITI NETWORKS does not warrant that the operation
of the Products will be error-free or that operation will be
uninterrupted. In no event shall UBIQUITI NETWORKS be
responsible for damages or claims of any nature or description
relating to system performance, including coverage, buyers
selection of products (including the Products) for buyers
application and/or failure of products (including the Products)
to meet government or regulatory requirements.
Limitation of Liability
EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO
EVENT WILL UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR
SUPPLIERS BE LIABLE FOR DIRECT, SPECIAL, INCIDENTAL,
CONSEQUENTIAL OR OTHER DAMAGES (INCLUDING LOST
PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING OUT OF
THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE
PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT
OR OTHER LEGAL THEORY, AND WHETHER OR NOT ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES.
Note
Some countries, states and provinces do not allow exclusions
of implied warranties or conditions, so the above exclusion
may not apply to you. You may have other rights that
vary from country to country, state to state, or province
to province. Some countries, states and provinces do not
allow the exclusion or limitation of liability for incidental or
consequential damages, so the above limitation may not
apply to you. EXCEPT TO THE EXTENT ALLOWED BY LOCAL
LAW, THESE WARRANTY TERMS DO NOT EXCLUDE, RESTRICT
OR MODIFY, AND ARE IN ADDITION TO, THE MANDATORY
STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY
SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The
United Nations Convention on Contracts for the International
Sale of Goods shall not apply to any transactions regarding
the sale of the Products.
Compliance
FCC
Changes or modifications not expressly approved by the party
responsible for compliance could void the users authority to
operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions.
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired
operation.
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to
radio communications. Operations of this equipment in a
residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at
his own expense.
Industry Canada
CAN ICES-3(A)/NMB-3(A)
This Class [A] digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe [A] est conforme à la
norme NMB-003 du Canada.
CE Marking
CE marking on this product represents the product is in
compliance with all directives that are applicable to it.
RoHS/WEEE Compliance Statement
English
European Directive 2002/96/EC requires that the equipment
bearing this symbol on the product and/or its packaging
must not be disposed of with unsorted municipal waste.
The symbol indicates that this product should be disposed
of separately from regular household waste streams. It is
your responsibility to dispose of this and other electric and
electronic equipment via designated collection facilities
appointed by the government or local authorities. Correct
disposal and recycling will help prevent potential negative
consequences to the environment and human health. For
more detailed information about the disposal of your old
equipment, please contact your local authorities, waste
disposal service, or the shop where you purchased the
product.
Deutsch
Die Europäische Richtlinie 2002/96/EC verlangt, dass
technische Ausrüstung, die direkt am Gerät und/oder an der
Verpackung mit diesem Symbol versehen ist, nicht zusammen
mit unsortiertem Gemeindeabfall entsorgt werden darf. Das
Symbol weist darauf hin, dass das Produkt von regulärem
Haushaltmüll getrennt entsorgt werden sollte. Es liegt in Ihrer
Verantwortung, dieses Gerät und andere elektrische und
elektronische Geräte über die dafür zuständigen und von
der Regierung oder örtlichen Behörden dazu bestimmten
Sammelstellen zu entsorgen. Ordnungsgemäßes Entsorgen
und Recyceln trägt dazu bei, potentielle negative Folgen für
Umwelt und die menschliche Gesundheit zu vermeiden. Wenn
Sie weitere Informationen zur Entsorgung Ihrer Altgeräte
benötigen, wenden Sie sich bitte an die örtlichen Behörden
oder städtischen Entsorgungsdienste oder an den Händler,
bei dem Sie das Produkt erworben haben.
Español
La Directiva 2002/96/CE de la UE exige que los equipos que
lleven este símbolo en el propio aparato y/o en su embalaje
no deben eliminarse junto con otros residuos urbanos no
seleccionados. El símbolo indica que el producto en cuestión
debe separarse de los residuos domésticos convencionales
con vistas a su eliminación. Es responsabilidad suya desechar
este y cualesquiera otros aparatos eléctricos y electrónicos a
través de los puntos de recogida que ponen a su disposición
el gobierno y las autoridades locales. Al desechar y reciclar
correctamente estos aparatos estará contribuyendo a evitar
posibles consecuencias negativas para el medio ambiente y
la salud de las personas. Si desea obtener información más
detallada sobre la eliminación segura de su aparato usado,
consulte a las autoridades locales, al servicio de recogida y
eliminación de residuos de su zona o pregunte en la tienda
donde adquirió el producto.
Français
La directive européenne 2002/96/CE exige que l’équipement
sur lequel est apposé ce symbole sur le produit et/ou son
emballage ne soit pas jeté avec les autres ordures ménagères.
Ce symbole indique que le produit doit être éliminé dans un
circuit distinct de celui pour les déchets des ménages. Il est
de votre responsabilité de jeter ce matériel ainsi que tout
autre matériel électrique ou électronique par les moyens de
collecte indiqués par le gouvernement et les pouvoirs publics
des collectivités territoriales. L’élimination et le recyclage en
bonne et due forme ont pour but de lutter contre l’impact
néfaste potentiel de ce type de produits sur l’environnement
et la santé publique. Pour plus d’informations sur le mode
d’élimination de votre ancien équipement, veuillez prendre
contact avec les pouvoirs publics locaux, le service de
traitement des déchets, ou l’endroit où vous avez acheté le
produit.
Italiano
La direttiva europea 2002/96/EC richiede che le
apparecchiature contrassegnate con questo simbolo sul
prodotto e/o sull’imballaggio non siano smaltite insieme ai
rifiuti urbani non differenziati. Il simbolo indica che questo
prodotto non deve essere smaltito insieme ai normali rifiuti
domestici. È responsabilità del proprietario smaltire sia
questi prodotti sia le altre apparecchiature elettriche ed
elettroniche mediante le specifiche strutture di raccolta
indicate dal governo o dagli enti pubblici locali. Il corretto
smaltimento ed il riciclaggio aiuteranno a prevenire
conseguenze potenzialmente negative per l’ambiente e per
la salute dell’essere umano. Per ricevere informazioni più
dettagliate circa lo smaltimento delle vecchie apparecchiature
in Vostro possesso, Vi invitiamo a contattare gli enti pubblici
di competenza, il servizio di smaltimento rifiuti o il negozio nel
quale avete acquistato il prodotto.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Ubiquiti CRM Point CRM-P Quick Start Quide

Tipo
Quick Start Quide

in altre lingue