Gigabyte H610M S2 V2 DDR4 Manuale del proprietario

Marca: Gigabyte

Modello: H610M S2 V2 DDR4

Tipo: Manuale del proprietario

Questo manuale è adatto anche per

H610M S2

For more product details, please visit GIGABYTE's website.

https://www.gigabyte.com/Motherboard/H610M-S2-rev-10?m=ma#kf

https://www.gigabyte.com/Motherboard/H610M-S2-V2-DDR4-rev-10?m=ma#kf

GIGABYTE will reduce paper use in order to fulll the responsibilities of a global citizen.

Also, to reduce the impacts on global warming, the packaging materials of this product

are recyclable and reusable. GIGABYTE works with you to protect the environment.

H610M S2

H610M S2 V2 DDR4

User's Manual

Rev. 1002

The trademarks mentioned in this manual are legally registered to their respective owners.

Disclaimer

Information in this manual is protected by copyright laws and is the property of GIGABYTE.

Changes to the specications and features in this manual may be made by GIGABYTE without

prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or

published in any form or by any means without GIGABYTE's prior written permission.

For detailed product information, carefully read the User's Manual.

For quick set-up of the product, refer to the Quick Installation Guide on GIGABYTE's

website.

https://download.gigabyte.com/FileList/Manual/mb_manual_quick-guide_am5.pdf?m=sw

For product-related information, check on our website at: https://www.gigabyte.com

Identifying Your Motherboard Revision

The revision number on your motherboard looks like this: "REV: X.X." For example, "REV: 1.0"

means the revision of the motherboard is 1.0. Check your motherboard revision before

updating motherboard BIOS, drivers, or when looking for technical information.

Example:

- 3 -

Table of Contents

Chapter 1 Product Introduction .......................................................................................4

1-1 Motherboard Layout ......................................................................................... 4

Chapter 2 Hardware Installation .....................................................................................6

2-1 Installation Precautions .................................................................................... 6

2-2 Product Specications ...................................................................................... 7

2-3 Installing the CPU and CPU Cooler ............................................................... 10

2-4 Installing the Memory ..................................................................................... 13

2-5 Installing an Expansion Card ......................................................................... 14

2-6 Back Panel Connectors .................................................................................. 15

2-7 Internal Connectors ........................................................................................ 17

Chapter 3 BIOS Setup ..................................................................................................28

Chapter 4 Installing the Operating System and Drivers ................................................ 30

Regulatory Notices .................................................................................................... 31

Contact Us ................................................................................................................ 32

- 4 -

1-1 Motherboard Layout

Chapter 1 Product Introduction

Temperature sensor

CPU_FAN

LGA1700

H610M S2

F_AUDIO

BAT

ATX_12V_2X4

Intel® H610

CODEC

CLR_CMOS

M_BIOS

PCIEX16

80 60

PCIEX1

iTE®

Super I/O

GbE LAN

Chip

F_USB1 F_PANEL

SPI_TPM

M2P_SB

SYS_FAN2

F_USB2

USB 2.0 Hub

COM LED_C

KB_MS

AUDIO

R_U32

VGA

USB_LAN

R_USB20

SYS_FAN1

ATX

F_U32

DDR5_A1

DDR5_B1

5 4

SATA3

7 6

SATA3

- 5 -

Temperature sensor

CPU_FAN

LGA1700

ATX

H610M S2 V2 DDR4

F_AUDIO

BAT

ATX_12V_2X4

Intel® H610

CODEC

CLR_CMOS

M_BIOS

PCIEX16

80 60

PCIEX1

iTE®

Super I/O

GbE LAN

Chip

F_USB1 F_PANEL

SPI_TPM

F_U32

DDR4_2

DDR4_1

M2P_SB

6 7

4 5

SATA3

SYS_FAN2

F_USB2

USB 2.0 Hub

COM LED_C

KB_MS

AUDIO

R_U32

VGA

USB_LAN

R_USB20

SYS_FAN1

- 6 -

2-1 Installation Precautions

The motherboard contains numerous delicate electronic circuits and components which can become

damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user's

manual and follow these procedures:

•Prior to installation, make sure the chassis is suitable for the motherboard.

•Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or

warranty sticker provided by your dealer. These stickers are required for warranty validation.

•Always remove the AC power by unplugging the power cord from the power outlet before

installing or removing the motherboard or other hardware components.

•When connecting hardware components to the internal connectors on the motherboard, make

sure they are connected tightly and securely.

•When handling the motherboard, avoid touching any metal leads or connectors.

•It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic

components such as a motherboard, CPU or memory. If you do not have an ESD wrist strap,

keep your hands dry and rst touch a metal object to eliminate static electricity.

•Prior to installing the motherboard, please have it on top of an antistatic pad or within an

electrostatic shielding container.

•Before connecting or unplugging the power supply cable from the motherboard, make sure

the power supply has been turned off.

•Before turning on the power, make sure the power supply voltage has been set according to

the local voltage standard.

•Before using the product, please verify that all cables and power connectors of your hardware

components are connected.

•To prevent damage to the motherboard, do not allow screws to come in contact with the

motherboard circuit or its components.

•Make sure there are no leftover screws or metal components placed on the motherboard or

within the computer casing.

•Do not place the computer system on an uneven surface.

•Do not place the computer system in a high-temperature or wet environment.

•Turning on the computer power during the installation process can lead to damage to system

components as well as physical harm to the user.

•If you are uncertain about any installation steps or have a problem related to the use of the

product, please consult a certied computer technician.

•If you use an adapter, extension power cable, or power strip, ensure to consult with its installation

and/or grounding instructions.

Chapter 2 Hardware Installation

- 7 -

2-2 ProductSpecications

CPU LGA1700 socket: Support for 13th Generation Intel® Core™ Processors and

12th Generation Intel® Core™, Pentium® Gold and Celeron® Processors

(Go to GIGABYTE's website for the latest CPU support list.)

L3 cache varies with CPU

Chipset Intel® H610 Express Chipset

Memory 13th Generation Intel® Core™ i9/i7 processors:

Support for DDR5 5600/5200/4800/4400 MT/s memory modules

 13th Generation Intel® Core™ i5/i3 and 12th Generation Intel® Core™, Pentium®

Gold and Celeron® Processors:

Support for DDR5 4800/4400 MT/s memory modules

Support for DDR4 3200/3000/2933/2666/2400/2133 MT/s memory modulesk

 2 x DDR DIMM sockets supporting up to 64 GB (32 GB single DIMM capacity)

of system memory

Dual channel memory architecture

 Support for ECC Un-buffered DIMM 1Rx8/2Rx8 memory modules (operate in

non-ECC mode)

Support for non-ECC Un-buffered DIMM 1Rx8/2Rx8/1Rx16 memory modules

Support for Extreme Memory Prole (XMP) memory modules

(Go to GIGABYTE's website for the latest supported memory speeds and memory

modules.)

Onboard

Graphics

Integrated Graphics Processor-Intel® HD Graphics support:

- 1 x D-Sub port, supporting a maximum resolution of 1920x1200@60 Hz

(Graphics specications may vary depending on CPU support.)

Audio Realtek® Audio CODEC

High Denition Audio

2/4/5.1/7.1-channel

* You can change the functionality of an audio jack using the audio software. To congure

7.1-channel audio, access the audio software for audio settings.

LAN Realtek® GbE LAN chip (1 Gbps/100 Mbps)

Expansion Slots CPU:

- 1 x PCI Express x16 slot, supporting PCIe 4.0 and running at x16

Chipset:

- 1 x PCI Express x1 slot, supporting PCIe 3.0 and running at x1

Storage Interface Chipset:

- 1 x M.2 connector (Socket 3, M key, type 2280/2260 PCIe 3.0 x4/x2 SSD

support)

- 4 x SATA 6Gb/s connectors

USB Chipset:

- 4 x USB 3.2 Gen 1 ports (2 ports on the back panel, 2 ports available through

the internal USB header)

- 4 x USB 2.0/1.1 ports on the back panel

Chipset+USB 2.0 Hub:

- 4 x USB 2.0/1.1 ports available through the internal USB headers

j Only for H610M S2.

k Only for H610M S2 V2 DDR4.

- 8 -

Internal

Connectors

1 x 24-pin ATX main power connector

1 x 8-pin ATX 12V power connector

1 x CPU fan header

2 x system fan headers

1 x M.2 Socket 3 connector

4 x SATA 6Gb/s connectors

1 x RGB LED strip header

1 x front panel header

1 x front panel audio header

1 x USB 3.2 Gen 1 header

2 x USB 2.0/1.1 headers

 1 x Trusted Platform Module header (For the GC-TPM2.0 SPI/GC-TPM2.0 SPI

2.0 module only)

1 x serial port header

1 x Clear CMOS jumper

Back Panel

Connectors

1 x PS/2 keyboard port

1 x PS/2 mouse port

1 x D-Sub port

2 x USB 3.2 Gen 1 ports

4 x USB 2.0/1.1 ports

1 x RJ-45 port

3 x audio jacks

I/O Controller iTE® I/O Controller Chip

Hardware

Monitor

Voltage detection

Temperature detection

Fan speed detection

Water cooling ow rate detection

Fan fail warning

Fan speed control

* Whether the fan speed control function is supported will depend on the cooler you

install.

BIOS 1 x 128 Mbit ash

Use of licensed AMI UEFI BIOS

PnP 1.0a, DMI 2.7, WfM 2.0, SM BIOS 2.7, ACPI 5.0

- 9 -

Unique Features Support for APP Center

* Available applications in APP Center may vary by motherboard model. Supported

functions of each application may also vary depending on motherboard specications.

- @BIOS

- Ambient LED

- EasyTune

- Smart Backup

- System Information Viewer

Support for Q-Flash

Support for Xpress Install

Bundled

Software

Norton® Internet Security (OEM version)

LAN bandwidth management software

Operating

System

Support for Windows 11 64-bit

Support for Windows 10 64-bit

Form Factor Micro ATX Form Factor; 23.0cm x 21.5cm

* GIGABYTE reserves the right to make any changes to the product specications and product-related information without

prior notice.

&Please visit GIGABYTE's website for support lists of CPU, memory modules, SSDs, and M.2 devices.

https://www.gigabyte.com/Motherboard/H610M-S2-rev-10?m=dl#support-dl

https://www.gigabyte.com/Motherboard/H610M-S2-V2-DDR4-rev-10?m=dl#support-dl

&Please visit the SERVICE/SUPPORT\Utility page on GIGABYTE's website to download the latest

version of apps.

https://www.gigabyte.com/Support/Utility/Motherboard?m=ut

- 10 -

2-3 Installing the CPU and CPU Cooler

Read the following guidelines before you begin to install the CPU:

•Make sure that the motherboard supports the CPU.

(Go to GIGABYTE's website for the latest CPU support list.)

•Always turn off the computer and unplug the power cord from the power outlet before installing the

CPU to prevent hardware damage.

•Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. (Or you may

locate the notches on both sides of the CPU and alignment keys on the CPU socket.)

•Apply an even and thin layer of thermal grease on the surface of the CPU.

•Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and damage

of the CPU may occur.

•Set the CPU host frequency in accordance with the CPU specications. It is not recommended

that the system bus frequency be set beyond hardware specications since it does not meet the

standard requirements for the peripherals. If you wish to set the frequency beyond the standard

specications, please do so according to your hardware specications including the CPU, graphics

card, memory, hard drive, etc.

A. Note the CPU Orientation

Note the alignment keys on the motherboard CPU socket and the notches on the CPU.

Alignment Key

LGA1700 CPU Socket

Triangle Pin One Marking

of the CPU Socket

Notch

LGA1700 CPU

Triangle Pin One

Marking on the CPU

Do not remove the CPU socket cover before inserting the CPU. It may pop off from the load

plate automatically after you insert the CPU and close the load plate.

&Please visit GIGABYTE's website for details on hardware installation.

http://www.gigabyte.com/WebPage/210/quick-guide.html?m=sw

- 11 -

Do not force to engage the CPU socket locking lever when the CPU is not installed correctly

as this would damage the CPU and CPU socket.

B. Installing the CPU

Follow the steps below to correctly install the CPU into the motherboard CPU socket.

jGently press the CPU socket lever handle

down and away from the socket.

kCompletely lift up the CPU socket lock-

ing lever.

lUse the finger tab on the side of the

metal load plate to lift open the metal

load plate with the plastic protective cover

attached to it.

Hold the CPU with your ngers by the edges.

Align the CPU pin one marking (triangle) with

the pin one corner of the CPU socket (or you

may align the CPU notches with the socket

alignment keys) and gently insert the CPU

into position.

Make sure the CPU is properly installed and

then close the load plate. The plastic protec-

tive cover will pop off, just remove it. Secure

the lever under its retention tab to complete

the installation of the CPU.

* Always replace the plastic protective cover

when the CPU is not installed to protect the

CPU socket.

Finger Tab

Pin One

- 12 -

C. Installing the CPU Cooler

Be sure to install the CPU cooler after installing the CPU. (Actual installation process may differ depending the

CPU cooler to be used. Refer to the user's manual for your CPU cooler.)

Apply an even and thin layer of thermal

grease on the surface of the installed CPU.

Place the cooler atop the CPU, aligning the

four push pins through the pin holes on the

motherboard. Push down on the push pins

diagonally.

Finally, attach the power connector of

the CPU cooler to the CPU fan header

(CPU_FAN) on the motherboard.

CPU_FAN

- 13 -

2-4 Installing the Memory

Read the following guidelines before you begin to install the memory:

•Make sure that the motherboard supports the memory. It is recommended that memory of the same

capacity, brand, speed, and chips be used. (Go to GIGABYTE's website for the latest supported

memory speeds and memory modules.)

•Always turn off the computer and unplug the power cord from the power outlet before installing the

memory to prevent hardware damage.

•Memory modules have a foolproof design. A memory module can be installed in only one direction.

If you are unable to insert the memory, switch the direction.

DualChannelMemoryConguration

This motherboard provides two memory sockets and supports Dual Channel Technology. After the memory

is installed, the BIOS will automatically detect the specications and capacity of the memory. Enabling Dual

Channel memory mode will double the original memory bandwidth.

The two memory sockets are divided into two channels and each channel has one memory socket as following:

Channel A: DDR5_A1j, DDR4_1k

Channel B: DDR5_B1j, DDR4_2k

Due to CPU limitations, read the following guidelines before installing the memory in Dual Channel mode.

1. Dual Channel mode cannot be enabled if only one memory module is installed.

2. When enabling Dual Channel mode with two memory modules, it is recommended that memory of the

same capacity, brand, speed, and chips be used.

DDR5_A1j, DDR4_1k

DDR5_B1j, DDR4_2k

j Only for H610M S2.

k Only for H610M S2 V2 DDR4.

- 14 -

2-5 Installing an Expansion Card

Read the following guidelines before you begin to install an expansion card:

•Make sure the motherboard supports the expansion card. Carefully read the manual that came

with your expansion card.

•Always turn off the computer and unplug the power cord from the power outlet before installing an

expansion card to prevent hardware damage.

Follow the steps below to correctly install your expansion card in the expansion slot.

1. Locate an expansion slot that supports your card. Remove the metal slot cover from the chassis back panel.

2. Align the card with the slot, and press down on the card until it is fully seated in the slot.

3. Make sure that the expansion card is fully seated in its slot.

4. Secure the card's metal bracket to the chassis back panel with a screw.

5. After installing all expansion cards, replace the chassis cover(s).

6. Turn on your computer. If necessary, go to BIOS Setup to make any required BIOS changes for your

expansion card(s).

7. Install the driver provided with the expansion card in your operating system.

PCIEX16 Slot

- 15 -

PS/2 Keyboard and PS/2 Mouse Port

Use the upper port (green) to connect a PS/2 mouse and the lower port (purple) to connect a PS/2 keyboard.

D-Sub Port

The D-Sub port supports a 15-pin D-Sub connector and supports a maximum resolution of 1920x1200@60 Hz

(the actual resolutions supported depend on the monitor being used). Connect a monitor that supports D-Sub

connection to this port.

USB 2.0/1.1 Port

The USB port supports the USB 2.0/1.1 specication. Use this port for USB devices.

USB 3.2 Gen 1 Port

The USB 3.2 Gen 1 port supports the USB 3.2 Gen 1 specication and is compatible to the USB 2.0

specication. Use this port for USB devices.

RJ-45 LAN Port

The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following

describes the states of the LAN port LEDs.

2-6 Back Panel Connectors

•When removing the cable connected to a back panel connector, rst remove the cable from your

device and then remove it from the motherboard.

•When removing the cable, pull it straight out from the connector. Do not rock it side to side to

prevent an electrical short inside the cable connector.

Line In/Rear Speaker Out (Blue)

The line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.

Line Out/Front Speaker Out (Green)

The line out jack.

Mic In/Center/Subwoofer Speaker Out (Pink)

The Mic in jack.

Activity LED

Speed LED

LAN Port

Activity LED:Speed LED:

State Description

Orange 1 Gbps data rate

Green 100 Mbps data rate

Off 10 Mbps data rate

State Description

Blinking Data transmission or receiving is occurring

Off No data transmission or receiving is occurring

- 16 -

&Please visit GIGABYTE's website for details on conguring the audio software.

https://www.gigabyte.com/WebPage/697/realtek897-audio.html

You can change the functionality of an audio jack using the audio software. To congure 7.1-channel

audio, access the audio software for audio settings.

Audio Jack Congurations:

Jack Headphone/

2-channel 4-channel 5.1-channel 7.1-channel

Line In/Rear Speaker Out a a a

Line Out/Front Speaker Out a a a a

Mic In/Center/Subwoofer Speaker Out a a

Front Panel Line Out/Side Speaker Out a

- 17 -

2-7 Internal Connectors

Read the following guidelines before connecting external devices:

•First make sure your devices are compliant with the connectors you wish to connect.

•Before installing the devices, be sure to turn off the devices and your computer. Unplug the power

cord from the power outlet to prevent damage to the devices.

•After installing the device and before turning on the computer, make sure the device cable has

been securely attached to the connector on the motherboard.

5119

1) ATX_12V_2X4

2) ATX

3) CPU_FAN

4) SYS_FAN1/SYS_FAN2

5) LED_C

6) SATA3 4/5/6/7

7) M2P_SB

8) F_PANEL

9) F_AUDIO

10) F_U32

11) F_USB1/F_USB2

12) COM

13) SPI_TPM

14) CLR_CMOS

15) BAT

12 13

H610M S2

- 18 -

Read the following guidelines before connecting external devices:

•First make sure your devices are compliant with the connectors you wish to connect.

•Before installing the devices, be sure to turn off the devices and your computer. Unplug the power

cord from the power outlet to prevent damage to the devices.

•After installing the device and before turning on the computer, make sure the device cable has

been securely attached to the connector on the motherboard.

5119

1) ATX_12V_2X4

2) ATX

3) CPU_FAN

4) SYS_FAN1/SYS_FAN2

5) LED_C

6) SATA3 4/5/6/7

7) M2P_SB

8) F_PANEL

9) F_AUDIO

10) F_U32

11) F_USB1/F_USB2

12) COM

13) SPI_TPM

14) CLR_CMOS

15) BAT

12 13

H610M S2 V2 DDR4

- 19 -

1/2) ATX_12V_2X4/ATX (2x4 12V Power Connector and 2x12 Main Power Connector)

With the use of the power connector, the power supply can supply enough stable power to all the components

on the motherboard. Before connecting the power connector, rst make sure the power supply is turned

off and all devices are properly installed. The power connector possesses a foolproof design. Connect the

power supply cable to the power connector in the correct orientation.

The 12V power connector mainly supplies power to the CPU. If the 12V power connector is not connected,

the computer will not start.

To meet expansion requirements, it is recommended that a power supply that can withstand high

power consumption be used (500W or greater). If a power supply is used that does not provide the

required power, the result can lead to an unstable or unbootable system.

ATX:

Pin No. Denition Pin No. Denition

1 3.3V 13 3.3V

2 3.3V 14 -12V

3 GND 15 GND

4 +5V 16 PS_ON (soft On/Off)

5 GND 17 GND

6 +5V 18 GND

7 GND 19 GND

8 Power Good 20 NC

9 5VSB (stand by +5V) 21 +5V

10 +12V 22 +5V

11 +12V (Only for 2x12-pin

ATX)

23 +5V (Only for 2x12-pin ATX)

12 3.3V (Only for 2x12-pin ATX) 24 GND (Only for 2x12-pin ATX)

ATX_12V_2X4:

Pin No. Denition

1 GND (Only for 2x4-pin 12V)

2 GND (Only for 2x4-pin 12V)

3 GND

4 GND

5+12V (Only for 2x4-pin 12V)

6+12V (Only for 2x4-pin 12V)

7 +12V

8 +12V

DEBUG

PORT

G.QBOFM

131

2412

ATX

ATX_12V_2X4

DEBUG

PORT

G.QBOFM

- 20 -

•Be sure to connect fan cables to the fan headers to prevent your CPU and system from

overheating. Overheating may result in damage to the CPU or the system may hang.

•These fan headers are not conguration jumper blocks. Do not place a jumper cap on the headers.

3/4) CPU_FAN/SYS_FAN1/SYS_FAN2 (Fan Headers)

All fan headers on this motherboard are 4-pin. Most fan headers possess a foolproof insertion design.

When connecting a fan cable, be sure to connect it in the correct orientation (the black connector wire is

the ground wire). The speed control function requires the use of a fan with fan speed control design. For

optimum heat dissipation, it is recommended that a system fan be installed inside the chassis.

CPU_FAN

SYS_FAN1

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

Pin No. Denition

1 GND

2 Voltage Speed Control

3 Sense

4 PWM Speed Control

Connector CPU_FAN SYS_FAN1 SYS_FAN2

Maximum Current 2A 2A 2A

Maximum Power 24W 24W 24W

DEBUG

PORT

G.QBOFM

SYS_FAN2

Before installing the devices, be sure to turn off the devices and your computer. Unplug the power

cord from the power outlet to prevent damage to the devices.

For how to turn on/off the lights of the LED strip, please navigate to the "Unique Features" page

of GIGABYTE's website.

5) LED_C (RGB LED Strip Header)

The header can be used to connect a standard 5050 RGB LED strip (12V/G/R/B), with maximum power

rating of 2A (12V) and maximum length of 2m.

Pin No. Denition

1 12V

2 G

3 R

4 B

DEBUG

PORT

G.QBOFM

RGB LED Strip

12V

Connect your RGB LED strip to

the header. The power pin (marked

with a triangle on the plug) of the

LED strip must be connected to

Pin 1 (12V) of this header. Incorrect

connection may lead to the damage

of the LED strip.

La pagina sta caricando ...

Gigabyte H610M S2 V2 DDR4 Manuale del proprietario

Marca: Gigabyte

Modello: H610M S2 V2 DDR4

Tipo: Manuale del proprietario

Questo manuale è adatto anche per

H610M S2

Scarica il pdf

rapporto

in altre lingue

English: Gigabyte H610M S2 V2 DDR4 Owner's manual

Gigabyte H610M S2 V2 DDR4 Manuale del proprietario

Questo manuale è adatto anche per

Gigabyte H610M S2 V2 DDR4 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti