Haier HAFRSJ64MC Manuale utente

CANDY HOOVER GROUP S.R.L. • Via Comolli 16 • 20861 Brugherio (MB) Italy

INDUCTION BUILT-IN COOKTOPS

INSTALLATION ADVICES - INSTRUCTIONS FOR THE USE GB

• HAIF64SC

PIANO DA INCASSO AD INDUZIONE

CONSIGLI PER L’INSTALLAZIONE - ISTRUZIONI PER L’USO IT

TABLES DE CUISSON ENCASTRABLES À INDUCTION

CONSEILS POUR L’INSTALLATION - MODE D’EMPLOI FR

PLACAS DE INDUCCIÓN ENCASTRABLES

CONSEJOS PARA LA INSTALACIÓN - INSTRUCCIONES DE USO ES

INDUKTIONS-EINBAUKOCHFELDER

INSTALLATIONSANLEITUNGEN - GEBRAUCHSANWEISUNG DE

22

Dear Customer,

Thank you for having purchased and given your preference

to our product.

The safety precautions and recommendations reported

below are for your own safety and that of others. They

will also provide a means by which to make full use of the

features oered by your appliance.

Please preserve this booklet carefully. It may be useful

in future, either to yourself or to others in the event that

doubts should arise relating to its operation.

This appliance must be used only for the task it

has explicitly been designed for, that is for cooking

foodstus. Any other form of usage is to be considered

as inappropriate and therefore dangerous.

The manufacturer declines all responsibility in the

event of damage caused by improper, incorrect or

illogical use of the appliance.

IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN

ACCORDANCE WITH EC DIRECTIVE 2012/19/EC.

At the end of its working life, the product must not be disposed of as

urban waste. It must be taken to a special local authority dierentiated

waste collection centre or to a dealer providing this service.

Disposing of a household appliance separately avoids possible negative

consequences for the environment and health deriving from inappropriate

disposal and enables the constituent materials to be recovered to obtain

signicant savings in energy and resources. As a reminder of the need

to dispose of household appliances separately, the product is marked

with a crossed-out wheeled dustbin.

DECLARATION OF CE CONFORMITY

• This appliance has been designed to be used only for cooking. Any other use (such as

heating a room) is improper and dangerous.

• This appliance has been designed, constructed, and marketed in compliance with:

- Safety requirements of the “Low voltage” Directive 2014/35/EU;

- Safety requirements of the “EMC” Directive 2014/30/EU;

- Requirements of EU Directive 93/68/EEC;

- Requirements of EU Directive 2011/65/EU.

33

IMPORTANT SAFETY PRECAUTIONS AND RECOMMENDATIONS

IMPORTANT: This appliance is designed and manufactured

solely for the cooking of domestic (household) food and is

not suitable for any non domestic application and therefore

should not be used in a commercial environment.

The appliance guarantee will be void if the appliance is used

within a non domestic environment i.e. a semi commercial,

commercial or communal environment.

Read the instructions carefully before installing and using

the appliance.

• This appliance has been designed and manufactured in

compliance with the applicable standards for the household

cooking products and it fullls all the safety requirements shown

in this manual, including those for surface temperatures.

Some people with sensitive skin may have a more pronounced

temperature perception with some components although these

parts are within the limits allowed by the norms.

The complete safety of the appliance also depends on the correct

use, we therefore recommend to always pay a extreme attention

while using the product, especially in the presence of children.

• After having unpacked the appliance, check to ensure that it is

not damaged.

In case of doubt, do not use it and consult your supplier or a

professionally qualied technician.

• Packing elements (i.e. plastic bags, polystyrene foam, nails,

packing straps, etc.) should not be left around within easy reach

of children, as these may cause serious injuries.

• Some appliances are supplied with a protective lm on steel and

aluminium parts. This lm must be removed before using the

appliance.

• IMPORTANT: The use of suitable protective clothing/gloves is

recommended when handling or cleaning this appliance.

44

• Do not attempt to modify the technical characteristics of

the appliance as this may become dangerous to use. The

manufacturer declines all responsibility for any inconvenience

resulting from the inobservance of this condition.

• Do not operate your appliance by means of an external timer or

separate remote-control system.

• Do not carry out cleaning or maintenance operations on the

appliance without having previously disconnected it from the

electric power supply.

• Do not use a steam cleaner because the moisture can get into

the appliance therefore making it unsafe.

• Do not cover the hob with aluminium foils.

• Do not touch the appliance with wet or damp hands (or feet).

• Do not use the appliance whilst in bare feet.

• If you should decide not to use this appliance any longer (or

decide to substitute another model), before disposing of it, it

is recommended that it be made inoperative in an appropriate

manner in accordance to health and environmental protection

regulations, ensuring in particular that all potentially hazardous

parts be made harmless, especially in relation to children who

could play with unused appliances.

• The various components of the appliance are recyclable. Dispose

of them in accordance with the regulations in force in your country.

If the appliance is to be scrapped, remove the power cord.

• After use, ensure that the controls are in the o position.

• Children less than 8 years of age shall be kept away unless

continuously supervised.

• This appliance can be used by children aged from 8 years and

above and persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge if they have

been given supervision or instruction concerning use of the

appliance in a safe way and understand the hazards involved.

Children shall not play with the appliance. Cleaning and user

maintenance shall not be made by children without supervision.

55

• The manufacturer declines all liability for injury to persons or

damage to property caused by incorrect or improper use of the

appliance.

• WARNING: During use the appliance and its accessible parts

become hot; they remain hot for some time after use.

– Care should be taken to avoid touching heating elements on

the hob.

– To avoid burns and scalds, young children should be kept

away.

• Make sure that electrical cables connecting other appliances in

the proximity of the cooktop cannot come into contact with the

hob.

• WARNING: Unattended cooking on a hob with fat or oil can be

dangerous and may result in re. NEVER try to extinguish a re

with water, but switch o the appliance and then cover ame e.g.

with a lid or a re blanket.

• WARNING: Danger of re: do not store items on the cooking

surfaces.

• Do not place or leave empty pans on the glass ceramic hob.

• Do not allow heavy or sharp objects to drop on the glass ceramic

hob.

• Do not scratch the hob with sharp objects. Don’t use the hob as

a work surface.

• WARNING: If the hob is cracked or otherwise damaged by falling

objects etc., disconnect the appliance from the electrical power

supply to avoid the possibility of electric shock and call Customer

Service.

• WARNING: When correctly installed, your product meets all

safety requirements laid down for this type of product category.

However special care should be taken around the underneath

of the appliance as this area is not designed or intended to be

touched and may contain sharp or rough edges, that may cause

injury.

• CAUTION: The cooking process has to be supervised. A short

term cooking process has to be supervised continuously.

66

• If the power supply cable is damaged, it must be replaced only

by an authorized service agent in order to avoid a hazard.

• If the appliance is not tted with a supply cord and a plug, or with

other means for disconnection from the supply mains having a

contact separation in all poles that provide full disconnection under

overvoltage category III conditions, means for disconnection

must be incorporated in the xed wiring in accordance with the

wiring rules.

• WARNING: The appliance and its accessible parts become hot

during use.

Care should be taken to avoid touching heating elements.

Children less than 8 years of age shall be kept away unless

continuously supervised.

• WARNING: Use only hob guards designed by the manufacturer

of the cooking appliance or indicated by the manufacturer of the

appliance in the instructions for use as suitable or hob guards

incorporated in the appliance. The use of inappropriate guards

can cause accidents.

• INDUCTION HOBS:

– Metallic objects such as knives, forks, spoons and lids should

not be placed on the hob surface since they can get hot.

– Do not use metallic kitchen utensils (e.g. ladles). It is preferable

to use plastic or wood kitchen utensils.

– Please use pans of recommended size (see minimum pan

diameter recommended). It is not advisable to use pans

smaller than the cooking zone. The pans have to be placed in

the centre of the cooking zone.

– Do not use defective pans or pans with a curved bottom.

– Please use suitable pans marked for induction cooking.

– Please keep your distance from the electromagnetic elds by

standing 5-10 cm from the cooking zones. When possible use

the rear cooking zones.

– Magnetic objects (e.g. credit cards, oppy disks, memory

cards) and electronic instruments (e.g. computers) should not

be placed near the induction hob.

77

– The heating of magnetic tins is forbidden! Closed tins may

explode by exceeding pressure while heating. There is a

burning risk with open tins as well, because the integrated

temperature protection will not work correctly.

– IMPORTANT WARNING: The induction hob complies with

European Standards for domestic cooking appliances.

Therefore it should not interfere with other electronic units.

Persons with cardiac pacemakers or any other electrical

implants must check with their doctor if they can use an induction

cooking system (and check any possible interferences with

the implants).

ENERGY LABELLING/ECODESIGN

• Commission regulation (EU) No 66/2014 (implementing Directive 2009/125/EC of the

European Parliament and of the Council).

Reference to the measurement and calculation methods used to establish compliance with

the above requirements:

• Standard EN 60350-2 (hobs: electric cooking zones and/or areas).

USE OF THE APPLIANCE, ENERGY SAVING TIPS

HOB

INDUCTION COOKING ZONES AND/OR AREAS

• To save electricity, use lids whenever possible.

• When the pan comes to the boil, turn the heat down to the level desired.

• Please use suitable pans marked for induction cooking. Some cookware available

on the market has an eective ferromagnetic area which is much smaller than the

diameter of the pan itself. Avoid using this cookware because the induction cooktop

may not function properly or may be damaged.

• Always use pans/coee pots with thick, completely at bottom. Do not use pans/coee

pots with concave or convex bottom; these could cause overheating of the cooking

zone.

• Important: Do not use pots/coee pot adaptors.

88

INSTALLATION

1

Advice for

the installer

IMPORTANT:

• The appliance is designed and approved for domestic use only and should not be

installed in a commercial, semi commercial or communal environment.

Your product will not be guaranteed if installed in any of the above environments

and could aect any third party or public liability insurances you may have.

• This appliance is to be installed only by an authorised person according to the current

local regulations and in observation of the manufacturer’s instructions.

Failure to comply with this condition will render the guarantee invalid.

• Incorrect installation, for which the manufacturer accepts no responsibility, may cause

personal injury of damage.

• This appliance shall only be serviced by authorized personnel.

• Always disconnect the cooktop from mains power supply before carrying out any

maintenance operations or repairs.

• Important: The use of suitable protective clothing/gloves is recommended when

handling or installing this appliance.

• The appliance must be housed in heat resistant units.

• The walls of the units must not be higher than work top and must be capable of

resisting temperatures of 70 °C above room temperature.

• We would point out that the adhesive which bonds the plastic laminate to the

furniture must withstand temperatures not less than 150 °C to avoid delamination.

• Do not install the appliance near inammable materials (eg. curtains).

WARNING

When correctly installed, your product meets all safety requirements laid down for

this type of product category.

However special care should be taken around the underneath of the appliance as

this area is not designed or intended to be touched and may contain sharp or rough

edges, that may cause injury.

99

FLUSH INSTALLATION (MODELS WITHOUT METAL TRIM/S ONLY)

If you wish to install the hob ush with the work surface, it is neccessary to execute/carry

out a miling in the hole of the cut-out as indicated in gs. 1.1b.

STANDARD INSTALLATION

Measures (mm)

Description A (*) B (*) C (**) D D1 E E1

30cm wide models 300

520

47

or

53 for ush

installation

270 305

480 525

60cm wide models 600 560 605

75cm wide models 750 560 755

80cm wide models 780 740 785

(*) For models with metal trim/s add 4mm to the measurement for each trim.

Example: front metal trim= B+4mm.

(**) from the top of countertop to bottom of cooktop.

E

50 mm

D

E

50 mm

D

50 mm

B

A

C

B

A

C

E1

D1

R7

5

50 mm

Fig. 1.1a

E

50 mm

D

E

50 mm

D

50 mm

B

A

C

B

A

C

E1

D1

R7

6

50 mm

Fig. 1.1b

1010

FITTING REQUIREMENTS

This cooktop can be built into a working surface from 20 mm thick and 600 mm deep.

In order to install the ceramic hob into the kitchen xture, a hole with the dimensions shown

in gures 1.1a or 1.1b has to be made, keeping in consideration the following:

• The cooktop shall not be installed directly above a dishwasher, fridge, freezer, washing

machine or clothes dryer, as the humidity may damage the cooktop electronics.

• If the cooktop is installed above an oven, the oven shall be provided with cooling fan.

The two appliances should be connected to the electrical supply with independent

connections.

• IMPORTANT WARNING! This cooktop requires adequate supply of fresh, cool

air to fully function. The base of the cooktop must have direct unrestricted

ventilation to the room where the cooktop is installed. Follow the requirements

of gure 1.3 or 1.4.

• There must be a distance of at least 500 mm between the hob and any wall cupboard

or extractor hood positioned immediately above (see g. 1.2).

• We would point out that the adhesive which bonds the plastic laminate to the

furniture must withstand temperatures not less than 150° C to avoid delamination.

• The walls of the units must be capable of resisting temperatures of 70 °C above

room temperature.

• Standard installation (not ush): Do not seal the cooktop into the benchtop with silicone

or glue; this makes future servicing dicult. The manufacturer will not cover the costs

of removing the cooktop, or of damage caused by this removal.

• The walls surrounding the cooktop must be made of heat-resistant material.

• Do not install the appliance near inammable materials (eg. curtains).

1111

min 5 mm

min 30 mm

min 25 mm

min 5 mm

min 30 mm

min 25 mm

Minimum clearances and

ventilation requirements

(oven installed below)

Minimum clearances and

ventilation requirements

(cupboard or drawer space below)

Oven with

cooling fan

650 mm

500 mm

450 mm

50 mm minimum

between the side of the

cut-out and the side wall

Fig. 1.2

Fig. 1.4Fig. 1.3

500 mm

1212

FASTENING THE COOKTOP

Each cooktop is provided with an installation kit including brackets and screws for fastening

the cooktop to benches from 20 mm thick. Before you install the cooktop, make sure that

the work surface is square and level, and no structural members interfere with space

requirements previously indicated.

The kit includes four metal clips “B” and four self-threading screws “A” (g. 1.5).

• Cut the unit according to the dimensions in g. 1.1a or 1.1b.

• Turn the hob upside down and rest the glass side on a soft surface.

• Spread the seal “D” around the edge of the hob (g. 1.6).

• Fasten the metal clips “B” into the hole “C” using the screws A”. Make sure that the

metal clips are mounted correctly as shown in the gure 1.5.

• Put the cooktop into the cutout and position it correctly.

• Using a sharp cutter or trimmer knife, trim the excess sealing material around the edge

of the cooktop. Take care not to damage the workbench.

• In case to install the hob ush with the work surface, ll any gaps between the glass

and along the perimeter of the work surface with insulating silicone, and wipe away

any excess.

D

Adhesive side

Fig. 1.6

C

B

A

B

A

Fig. 1.5

Glass

Metal clips

Fixing screw

Worktop / kitchen cabinet

Seal “D”

IMPORTANT: Spread

the sealing material “D”

around the edge of the

hob (edge of the glass).

The sealing material

“D” must be installed

correctly to guarantee a

perfect seal between the

appliance and the unit.

Incorrect installation may

cause irreparable damage

to the appliance.

1313

ELECTRICAL SECTION

2

IMPORTANT: Installation must be carried out according to the manufacturer’s

instructions. Incorrect installation may cause harm and damage to people,

animals or property, for which the manufacturer accepts no responsibility.

Before carrying out any work on the electrical section of the appliance, it must be

disconnected from the mains.

Connection to a good earth wiring system is absolutely essential.

The manufacturer accepts no responsibility for any inconvenience caused by

failure to comply with this rule.

If the hob surface is cracked disconnect the appliance from the mains and contact

the After-Sales Service.

ELECTRICAL REQUIREMENTS

• Connection to the electric power supply must be carried out by a qualied technician

and following the appropriate safety regulations.

• The appliance must be connected to the mains checking that the voltage corresponds

to the value given in the rating plate and that the electrical cable sections can withstand

the load specied on the plate.

• The appliance should be connected directly to the mains placing an omnipolar switch

with minimum opening between the contacts of 3 mm between the appliance and the

mains.

• The power supply cable must not touch the hot parts and must be positioned so that it

does not exceed 50°C above ambient.

• Once the appliance has been installed, the switch must always be in a accessible

position.

N.B. For connections to the mains power supply, never use adaptors, reductions or

multiple power points as these may overheat and catch re.

In the event that installation should require modications to the mains supply wiring system,

it is recommended that a qualied technician be called to carry out substitution.

He should also check that the domestic electrical system is suitable for the power absorbed

by the appliance.

1414

FEEDER CABLE SECTION TYPE:

• H05RR-F, H07RN-F;

• or H05VV-F, H05V2V2-F (resistant to temperatures of 90°C)

For 30 cm models:

220-240 V ac 3 x 2,5 mm2 (*)

For 60, 75, 80 cm models:

220-240 V ac 3 x 6 mm2 (*), or 3 x 4 mm2 (*) (**) or 5 x 2,5 mm2 (*) (***)

380-415 V 2N ac 5 x 2,5 mm2 (*) (***)

380-415 V 3N ac 5 x 2,5 mm2 (*) (***)

(*) Connection with wall box connection.

(**) Only for 60 cm model with 3 zones.

(***) See also chapter “MODELS SUPPLIED WITH POWER CORD 5x2,5 mm2

ALREADY FITTED TO THE APPLIANCE “ and g. 2.4 or 2.5 or 2.6.

If the supply cord is damaged, it must be replaced by the manufacturer or its service

agent or a similarly qualied person in order to avoid a hazard.

FEEDER CABLE SECTION TYPE:

• H05RR-F, H07RN-F;

• or H05VV-F, H05V2V2-F (resistant to temperatures of 90°C)

For 30 cm models:

220-240 V ac 3 x 2,5 mm2 (*)

For 60, 75, 80 cm models:

220-240 V ac 3 x 6 mm2 (*), or 3 x 4 mm2 (*) (**)

380-415 V 2N ac 4 x 2,5 mm2 (*)

380-415 V 3N ac 5 x 2,5 mm2 (*)

(*) Connection with wall box connection.

(**) Only for 60 cm model with 3 zones.

MODELS SUPPLIED WITHOUT POWER CORD

ALREADY FITTED TO THE APPLIANCE

MODELS SUPPLIED WITH POWER CORD

ALREADY FITTED TO THE APPLIANCE

1515

CONNECTION OF THE POWER SUPPLY CABLE

Important! This cooktop must be connected to the electricity supply only by an

authorised person.

To connect the feeder cable to the hob it is necessary to carry out the following operations:

• Unscrew the screw “A”

• Unhook the terminal board cover by inserting a screwdriver into the two hooks “B” (g.

2.1). Open completely the terminal block cover.

• Unscrew the screw “C”, then unhook the cable clamp “D” by inserting a screwdriver

into the hook “E”. Remove completely the cable clamp “D” (g. 2.2).

• Connect the phase, neutral and earth wires to terminal board according to the diagrams

in g. 2.3.

• Strain the feeder cable and block it with cable clamp “D” (by hooking hook “E” and

screwing screw “C”).

• Close the cover of the terminal board (check the two hooks “B” are correctly hooked and

screwing screw “A”

).

NOTE: The earth conductor must be left about 3 cm longer than the others.

The operations must be executed by a qualied technician.

220 - 240 V ac

L N PE

380 - 415 V 2N ac 380 - 415 V 3N ac

L1L2N PE L1L3L2N PE

Fig. 2.3

1

2

1

2

AB

B

C

E

D

Fig. 2.1 Fig. 2.2

1616

• The cooktop is supplied with a power cord already tted to the appliance and it is

suitable for a single-phase type electrical connection. (g. 2.4).

• For the two-phase type electrical connection (g. 2.5):

– separate the black and brown wires by removing the metallic terminal;

– remove about 5 mm of the insulation sheathing from the terminal end of the black

and brown wires;

– tightly t a new metallic terminal (2,5 mm) on the terminal end of each wire (black

and brown).

• For the tree-phase type electrical connection (g. 2.6):

– separate the black and brown wires by removing the metallic terminal;

– separate the blue and gray wires by removing the metallic terminal;

– remove about 5 mm of the insulation sheathing from the terminal ends of the black,

brown, blue and gray wires;

– tightly t a new metallic terminal (2,5 mm) on the terminal end of each wire (black,

brown, blue and gray);

– disconnect the gray wire from the terminal block (to access the terminal block see

chapter “CONNECTION OF THE POWER SUPPLY CABLE”) and connect it to the

L3 terminal of the terminal block. Position the U-bolt between the terminals N1 and

N2 of the terminal block and close its cover.

MODELS SUPPLIED WITH POWER CORD 5x2,5 mm2

ALREADY FITTED TO THE APPLIANCE

ATTENTION!

All the operations/electrical connections must be carried out by a qualied technician.

CAUTION!

Do not pierce or weld the terminal ends of the wires. This is strictly forbidden!

CAUTION!

Do not connect the power cord to the electrical power supply without the metallic terminals

correctly in place.

If the supply cord is damaged, it must be replaced by the manufacturer or its service

agent or a similarly qualied person in order to avoid a hazard.

1717

“220-240 V ac”

connection

“380-415 V 2N ac”

connection

“380-415 V 3N ac”

connection

Green - Yellow Green - Yellow Green - Yellow

NBlue and Gray NBlue and Gray NBlue

LBlack and Brown L1 Black L1 Black

/L2 Brown L2 Brown

/ / L3 Gray

L

N

L1

N

L2

220...240 V ac

220-240 V ac

380-415 V 2N ac

L

N

L1

N

L2

220...240 V ac

220-240 V ac

380-415 V 2N ac

Fig. 2.4

Fig. 2.5

L

N

L1

N

L2

220...240 V ac

220-240 V ac

380-415 V 2N ac

L1

L3

L2

380-415 V 3N ac

N

220...240 V ac

Fig. 2.6

380-415 V 3N ac

380-415 V 2N ac

220-240 V ac

1818

1919

ADVICEADVICE

for thefor the

USERSUSERS

2020

FEATURES AND TECHNICAL DATA

1

Fig. 1.1

4

2

3

1

2

3

2

3

1

4

5

1

2

3

1

OLD

1

4

2

3

1

2

3

2

3

1

4

5

1

2

3

1

OLD

1

30cm wide models

60cm wide models

75cm wide models 80cm wide models

Fig. 1.2 Fig. 1.3 Fig. 1.4

Fig. 1.5 Fig. 1.6

These gures are indicative only.

Caution! Do not cover the hob with aluminium foils.

4

2

3

1

2

3

2

3

1

4

5

1

2

3

1

OLD

1

4

2

3

1

2

3

2

3

1

4

5

1

2

3

1

OLD

1

4

2

3

1

2

3

2

3

1

4

5

1

2

3

1

OLD

1

4

2

3

1

2

3

2

3

1

4

5

1

2

3

1

OLD

1

La pagina sta caricando ...

Haier HAFRSJ64MC Manuale utente

Haier HAFRSJ64MC Manuale utente

in altre lingue