LD Systems DIO 04 Manuale utente

USER´S MANUAL

BEDIENUNGSANLEITUNG

MANUEL D´UTILISATION

MANUAL DE USUARIO

INSTRUKCJA OBSŁUGI

MANUALE D´USO

DIO 04

4 OUTPUT DANTE INTERFACE

LDDIO04

CONTENTS / INHALTSVERZEICHNIS / CONTENU / CONTENIDO / TREŚĆ / CONTENUTO

ENGLISH

ABOUT THIS MANUAL 4

INTENDED USE 4

EXPLANATIONS OF TERMS AND SYMBOLS 4

SAFETY INSTRUCTIONS 5

NOTES FOR INDOOR INSTALLATION EQUIPMENT 7

PACKAGING CONTENT 8

INTRODUCTION 8

CONNECTIONS, OPERATING AND

DISPLAY ELEMENTS 9

CONNECTION EXAMPLES 10

TERMINAL BLOCK CONNECTIONS 12

DANTE® CONTROLLER 13

UNDER / ON-TABLE MOUNTING 14

CARE, MAINTENANCE AND REPAIR 14

DIMENSIONS 15

TECHNICAL DATA 16

DISPOSAL 17

MANUFACTURER´S DECLARATIONS 18

DEUTSCH

INFORMATIONEN ZU DIESER

BEDIENUNGSANLEITUNG 19

BESTIMMUNGSGEMÄSSER GEBRAUCH 19

BEGRIFFS- UND SYMBOLERKLÄRUNGEN 19

SICHERHEITSHINWEISE 20

HINWEISE FÜR INDOOR-INSTALLATIONSGERÄTE 23

LIEFERUMFANG 23

EINLEITUNG 23

ANSCHLÜSSE, BEDIEN- UND ANZEIGEELEMENTE 24

ANSCHLUSSBEISPIELE 26

KLEMMLEISTENANSCHLÜSSE 27

DANTE® CONTROLLER 28

UNTER- / AUFTISCHMONTAGE 29

PFLEGE, WARTUNG UND REPARATUR 29

ABMESSUNGEN 30

TECHNISCHE DATEN 31

ENTSORGUNG 32

HERSTELLERERKLÄRUNGEN 33

FRANCAIS

INFORMATIONS SUR CE MODE D‘EMPLOI 34

UTILISATION RÉGLEMENTÉE 34

EXPLICATIONS DES TERMES ET DES SYMBOLES 34

CONSIGNES DE SÉCURITÉ 35

NOTES POUR L’ÉQUIPEMENT

D’INSTALLATION À L’INTÉRIEUR 38

CONTENU DU CARTON 38

INTRODUCTION 38

CONNECTEURS, UTILISATION ET INDICATEURS 39

EXEMPLES DE CONNEXION 41

CONNECTEURS EUROBLOCK (BORNIERS) 42

LOGICIEL DANTE® CONTROLLER 43

MONTAGE SOUS / SUR TABLE 44

ENTRETIEN, MAINTENANCE ET RÉPARATION 44

DIMENSIONS 45

CARACTÉRISTIQUES TECHNIQUES 46

MISE EN DÉCHETTERIE 47

DÉCLARATIONS DU FABRICANT 48

ESPAÑOL

INFORMACIÓN SOBRE ESTAS

INSTRUCCIONES DE USO 49

USO CONFORME A LA NORMATIVA 49

EXPLICACIONES DE TÉRMINOS Y SíMBOLOS 49

INSTRUCCIONES DE SEGURIDAD 50

NOTAS PARA LOS EQUIPOS

DE INSTALACIÓN EN INTERIORES 53

CONTENIDO DEL EMBALAJE 53

INTRODUCCIÓN 53

CONEXIONES, MANDOS E INDICADORES 54

EJEMPLOS DE CONEXIÓN 56

CONEXIONES DEL BLOQUE DE TERMINALES 57

DANTE® CONTROLLER 58

MONTAJE BAJO/SOBRE LA MESA 59

CUIDADO, MANTENIMIENTO Y REPARACIÓN 59

DIMENSIONES 60

DATOS TÉCNICOS 61

DISPOSICIÓN 62

DECLARACIONES DEL FABRICANTE 63

POLSKI

INFORMACJE DOTYCZĄCE NINIEJSZEJ INSTRUKCJI

OBSŁUGI 64

STOSOWANIE ZGODNIE Z PRZEPISAMI 64

OBJAŚNIENIA TERMINÓW I SYMBOLI 64

INSTRUKCJE BEZPIECZEŃSTWA 65

UWAGI DOTYCZĄCE SPRZĘTU DO INSTALACJI

WEWNĘTRZNYCH 67

ZAWARTOŚĆ OPAKOWANIA 67

WPROWADZENIE 67

PRZYŁĄCZA, ELEMENTY OBSŁUGI I WSKAŹNIKI 68

PRZYKŁADY POŁĄCZEŃ 70

POŁĄCZENIA TERMINALI ZACISKOWYCH 71

KONTROLER DANTE 72

MONTAŻ POD / NA BLACIE 73

PIELĘGNACJA, KONSERWACJA I NAPRAWA 73

WYMIARY 74

DANE TECHNICZNE 75

DYSPOZYCJA 76

OŚWIADCZENIA PRODUCENTA 77

ITALIANO

INFORMAZIONI SU QUESTE ISTRUZIONI PER L‘USO 78

UTILIZZO IN CONFORMITÀ ALLE NORMATIVE 78

SPIEGAZIONI DI TERMINI E SIMBOLI 78

ISTRUZIONI DI SICUREZZA 79

NOTE PER LE APPARECCHIATURE

DI INSTALLAZIONE ALL’INTERNO 81

CONTENUTO DELL’IMBALLAGGIO 82

INTRODUZIONE 82

CONNESSIONI, ELEMENTI DI COMANDO E

DI VISUALIZZAZIONE 83

ESEMPI DI CONNESSIONE 85

COLLEGAMENTI DELLA MORSETTIERA 86

DANTE® CONTROLLER 87

MONTAGGIO SOTTO/SU TAVOLO 88

CURA, MANUTENZIONE E RIPARAZIONE 88

DIMENSIONI 89

DATI TECNICI 90

SMALTIMENTO 91

DICHIARAZIONI DEL PRODUTTORE 92

4

ENGLISH

YOU MADE THE RIGHT CHOICE!

This device was developed and manufactured under high quality requirements to ensure many

years of trouble-free operation. This is what LD Systems stands for with its name and many years

of experience as a manufacturer of high-quality audio products. Please read these operating

instructions carefully so that you can quickly and optimally use your new LD Systems product.

You can find more information about LD Systems on our website WWW.LD-SYSTEMS.COM

ABOUT THIS MANUAL

• Read the safety instructions and the entire manual carefully before commissioning.

• Observe the warnings on the unit and in the operating instructions.

• Always keep the operating instructions within reach.

• If you sell or pass on the appliance, be sure to hand over these operating instructions as well,

as they are an essential part of the product.

INTENDED USE

The product is a device for professional audio installation! The product has been developed for

professional use in the field of audio installation and is not intended for use in households!

Furthermore, this product is intended for installation by qualified persons with specialist

knowledge and for operation by instructed persons! The use of the product outside the specified

technical data and operating conditions is considered as not intended! Liability for damages and

third party damages to persons and property due to non-intended use is excluded!

The product is not suitable for:

• Persons (including children) with limited physical, sensory or mental capabilities or lack of

experience and knowledge.

• Children (children must be instructed not to play with the device).

EXPLANATIONS OF TERMS AND SYMBOLS

1. DANGER: The word DANGER, possibly in combination with a symbol, indicates immediately

dangerous situations or conditions for life and limb.

2. WARNING: The word WARNING, possibly in combination with a symbol, indicates potentially

dangerous situations or conditions for life and limb.

3. CAUTION: The word CAUTION, possibly in combination with a symbol, is used to indicate

situations or conditions that may lead to injury.

4. ATTENTION: The word ATTENTION, possibly in combination with a symbol, refers to situations

or states that can lead to damage to property and/or the environment.

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

5

This symbol indicates hazards that can cause an electric shock.

This symbol indicates danger spots or dangerous situations.

This symbol indicates danger from hot surfaces.

This symbol indicates danger from high volumes.

This symbol indicates supplementary information on the operation of the product.

This symbol denotes a device that does not contain any user-serviceable parts.

This symbol indicates electrical equipment designed primarily for indoor use.

SAFETY INSTRUCTIONS

DANGER:

1. Do not open or modify the device.

2. If your device is no longer working properly, liquids or objects have gotten inside

the device, or the device has been damaged in any other way, switch it off immediately

and disconnect it from the power supply. This device may only be repaired by

authorized specialist personnel.

3. For devices of protection class 1, the protective conductor must be connected

correctly. Never interrupt the protective conductor. Protection class 2 devices

do not have a protective conductor.

4. Ensure that live cables are not kinked or otherwise mechanically damaged.

5. Never bypass the device fuse.

WARNING:

1. The device must not be put into operation if it shows obvious signs of damage.

2. The device may only be installed in a voltage-free state.

3. If the power cord of the device is damaged, the device must not be put into operation.

4. Permanently connected power cords may only be replaced by a qualified person.

DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

6

DANGER:

1. Do not operate the device if it has been exposed to severe temperature fluctuations

(e.g. after transport). Humidity and condensation could damage the device.

Do not switch on the device until it has reached the ambient temperature.

2. Make sure that the voltage and frequency of the mains supply correspond to the

values indicated on the device. If the device has a voltage selector switch, do not

connect the device until this is set correctly. Only use suitable power cords.

3. To disconnect the device from the mains at all poles, it is not enough to press the

on/off switch on the device.

4. Ensure that the fuse used corresponds to the type printed on the device.

5. Make sure that appropriate measures against overvoltage (e.g. lightning) have

been taken.

6. Note the specified maximum output current on devices with a power out connection.

Make sure that the total power consumption of all connected devices does not

exceed the specified value.

7. Only replace pluggable power cords with original cables.

DANGER:

1. Danger of suffocation! Plastic bags and small parts must be kept out of the reach of

people (including children) with reduced physical, sensory or mental abilities.

2. Danger from falling! Make sure the device is installed securely and cannot fall.

Only use suitable tripods or attachments (especially for fixed installations).

Make sure accessories are properly installed and secured. Make sure that the

applicable safety regulations are observed.

WARNING:

1. Only use the device in the manner intended.

2. Only operate the device with the accessories recommended and intended by the

manufacturer.

3. During installation, observe the safety regulations applicable in your country.

4. After connecting the unit, check all cable routes to avoid damage or accidents,

e.g. due to tripping hazards.

5. Be sure to observe the specified minimum distance to normally flammable

materials! Unless this is explicitly stated, the minimum distance is 0.3 m.

ATTENTION:

1. There is a risk of jamming with moving components such as mounting brackets or

other moving components.

2. In the case of units with motor-driven components, there is a risk of injury from the

movement of the unit. Sudden device movement can cause shockreactions.

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

7

DANGER:

1. Do not install or operate the device near radiators, heat registers, stoves or other

heat sources. Make sure that the device is always installed in such a way that it is

sufficiently cooled and cannot overheat.

2. Do not place any sources of ignition such as burning candles near the device.

3. Ventilation openings must not be covered and fans must not be blocked.

4. Use the original packaging or packaging provided by the manufacturer for transport.

5. Avoid shock or shock to the device.

6.

Observe the IP protection class and the environmental conditions such as temperature

and humidity according to the specification.

7. Devices can be continuously developed. In the event of deviating information on

operating conditions, performance or other device properties between the operating

instructions and the device labeling, the information on the device always has

priority.

8. The device is not suitable for tropical climate zones and for operation above

2000 m above sea level.

ATTENTION:

Connecting signal cables can result in significant noise interference. Make sure that

devices connected to the output are muted during plugging. Otherwise, noise levels

can cause damage.

ATTENTION HIGH VOLUMES WITH AUDIO PRODUCTS!

This device is intended for professional use.

The commercial operation of this device is subject to the applicable national

regulations and guidelines for accident prevention.

Hearing damage due to high volumes and continuous exposure: The use of this product

can generate high sound pressure levels (SPL) which can cause hearing damage.

Avoid exposure to high volumes.

NOTES FOR INDOOR INSTALLATION EQUIPMENT

1. Units for installation applications are designed for continuous operation.

2. Units for indoor installation are not weatherproof.

3. Surfaces and plastic parts of installation equipment can also age, e.g. due to UV

radiation and temperature fluctuations. This does not usually lead to functional

restrictions.

4. with permanently installed units, the deposition of impurities, e.g. dust, is to be

expected. Be sure to observe the care instructions.

5. Unless explicitly stated otherwise on the unit, the units are intended for installation

heights of less than 5 m.

DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

8

PACKAGING CONTENT

Remove the product from the packaging and remove all packaging material.

Please check the completeness and integrity of the delivery and notify your distribution partner

immediately after purchase if the delivery is not complete or if it is damaged.

The packaging includes:

• 1 x DIO 04 Dante Break Out Box

• 1 set of terminal blocks

• 1 set of rubber feet (pre-assembled)

• 1 mounting set for on-table or under-table installation

• User manual

INTRODUCTION

Part of the TICA® series, the DIO 04 is a four output Dante interface that delivers the capabilities

that audio and AV professionals really need. Equipped with four balanced outputs to connect

to any analogue audio device such as power amplifiers Signal presence lights on each channel

speed installation and fault-finding.

Power from any PoE+ network switch or use the optional, external power supply. Since it comes

with two Dante networked ports, you can daisy chain devices together. It also works as a PoE+

injector: if you use the external power supply, you can power one further networked device in

the chain.

It’s tiny form factor (106 x 44 x 222 mm) and included mounting plates allow it to be installed

discreetly behind screens or under tables. Alternatively, it fits into 1/3 19 inch rack.

Use the optional rack tray to slot up to three TICA® DIO series products alongside each other

and build a system to your exact requirements, using minimal rack space.

Terminal block connections on the analogue outputs make wiring easy.

The perfect solution for professional installers wanting to interface into Dante equipment.

Dante Domain Manager and AES 67 compliant.

FEATURES

• Four output Dante interface

• Connect Dante to line level audio equipment

• Terminal blocks for all analogue connecitons

• Signal indicators on each channel

• Use PoE or an external power supply

• Use as a PoE injector to power another networked device

• Daisy-chain Dante devices together

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

9

CONNECTIONS, OPERATING AND DISPLAY ELEMENTS

4

3

5

1 2

1 TERMINAL BLOCK CONNECTION FOR POWER SUPPLY

Terminal block connection for the device's power supply. To avoid damage to the unit, please use

only the original power supply unit (power supply unit optionally available).

Alternative power supply: Ethernet switch or PoE injector with PoE+ (Power over Ethernet plus)

or better.

2 STRAIN RELIEF

Use the strain relief for the flexible cable of the power supply unit to protect the device's power

terminal block connector and the power supply terminal block from damage and to prevent the

terminal block from being pulled out unintentionally.

3 OUTPUT 1 – 4

Analogue audio outputs with balanced terminal block connections. The poles +, - and G are

intended for the balanced output signal (suitable for unbalanced cabling). Terminal blocks are

included in the packaging content. If there is no audio signal at the line outputs OUTPUT 1 to 4,

they are automatically muted after some time. If an audio signal is detected, the mute function

is automatically deactivated.

4 PSE+DATA (Power Sourcing Equipment)

Dante® interface with RJ45 socket for connecting further Dante® devices to the Dante® network.

If the DIO 04 is supplied with power via an external power supply unit, another DIO 04 can be

supplied with power via PoE (see connection example 2).

5 PD+DATA (Powered Device)

Dante® interface with RJ45 socket for connecting the DIO 04 to a Dante® network.

The DIO 04 can be supplied with voltage via PoE+ (Power over Ethernet plus) or better.

7

6

DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

10

6 POWER SYMBOL

As soon as the DIO 04 is supplied with voltage, the starting process begins. During the start-up

process, the white power symbol flashes and the line outputs OUTPUT 1 to 4 are muted.

When the start-up process is completed after a few seconds, the symbol lights up permanently

and the unit is ready for operation.

7 SIGNAL OUTPUT 1 – 4

Two-colour illuminated digits 1 to 4 for signal detection and clip display.

OUTPUT: As soon as an audio signal with sufficient level is present at an output channel, the

corresponding digit lights up white. As soon as one of the digits lights up red, the corresponding

output stage is operated at the distortion limit. In this case, reduce the level on the source player

so that the digit no longer lights up red.

AIR VENTS

To prevent damage to the device, do not cover the ventilation openings on the left and right

sides and on the top and bottom of the device and ensure that air can circulate freely. Covering

the ventilation openings on the top or bottom of the enclosure when mounting it underneath

or on top of a table is not critical, as the cooling provided by the ventilation openings on the

remaining sides is sufficient.

Tip: Preferably use balanced audio cables for wiring analogue line inputs and outputs.

CONNECTION EXAMPLES

1

Dante™ Mixer

Dante® Controller

Questra

Dante® Controller

INPUTS

1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8POWER

ZONE X 1208D

NETWORK

REMOTE

9 10 11 12

OUTPUTS

Active Loudspeaker

ON

23 4

DIP

ON

1 2 3 4

DIP

ON

1 2 3 4

DIPON

1 2 3 4

DIP

24V DC

Power supply

24V DC

Power supply

Ethernet Switch

PoEPoE

OUTPUT 1 - 4

touch control wall panel

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

11

2

Dante™ Mixer

Dante® Controller

Questra

Dante® Controller

INPUTS

1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8POWER

ZONE X 1208D

NETWORK

REMOTE

9 10 11 12

OUTPUTS

Active Loudspeaker

ON

23 4

DIP

ON

1 2 3 4

DIP

ON

1 2 3 4

DIPON

1 2 3 4

DIP

24V DC

Power supply

24V DC

Power supply

Ethernet Switch

PoEPoE

OUTPUT 1 - 4

touch control wall panel

3

Dante™ Mixer

Dante® Controller

Questra

Dante® Controller

INPUTS

1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8POWER

ZONE X 1208D

NETWORK

REMOTE

9 10 11 12

OUTPUTS

Active Loudspeaker

ON

23 4

DIP

ON

1 2 3 4

DIP

ON

1 2 3 4

DIPON

1 2 3 4

DIP

24V DC

Power supply

24V DC

Power supply

Ethernet Switch

PoEPoE

OUTPUT 1 - 4

touch control wall panel

4

Dante® Controller

INPUTS

1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8POWER

ZONE X 1208D

NETWORK

REMOTE

9 10 11 12

OUTPUTS

Ethernet Switch

PoEPoE

OUTPUT 1 - 4

touch control wall panel

QTP 8

DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

12

TERMINAL BLOCK CONNECTIONS

OUTPUT connections

balanced

unbalanced

When wiring terminal blocks, please observe the correct assignment of the poles/

terminals. The manufacturer accepts no liability for damage caused by faulty wiring!

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

13

DANTE® CONTROLLER

A Dante® network is set up using the freely available DANTE® CONTROLLER software. Download

the software from the manufacturer's website www.audinate.com and install it on a computer.

Connect the computer's Ethernet interface to a network interface using a network cable (Cat. 5e

or better) and run the Dante® Controller software. The software has an automatic device detection

function. Signal routing is done by mouse click and the unit and channel designations can be

individually edited by the user. IP address, MAC address and other information about the devices

in the Dante® network can be displayed in the software.

Once the configuration of the devices on the Dante® network is complete, the Dante® Controller

software can be closed and the computer disconnected from the network. The settings in the

units in the network are retained.

When the DIO 04 is disconnected from the Dante® network, the unit's audio outputs are muted

and the power icon on the front panel starts flashing.

DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

14

UNDER / ON-TABLE MOUNTING

There are two recesses on the top and bottom of the enclosure, each with two M3 threaded

holes, for mounting underneath or on top of the table. Screw the two enclosed mounting plates

to the top or bottom using the enclosed M3 countersunk screws. Now the amplifier can be fixed

in the desired position (see illustration, fixing screws not included). For tabletop mounting, the

four rubber feet must be removed beforehand.

CARE, MAINTENANCE AND REPAIR

To ensure the proper functioning of the unit in the long term, it must be cared for regularly and

serviced as required. The need for care and maintenance depends on the intensity of use and

the environment.

We generally recommend a visual inspection before each start-up. Furthermore, we recommend

that you carry out all the maintenance measures listed below every 500 operating hours or, in

the case of low intensity of use, after one year at the latest. Defects caused by inadequate care

may result in limitations of the warranty claims.

CARE (CAN BE CARRIED OUT BY THE USER)

WARNING! Before carrying out any maintenance work, disconnect the power supply

and, if possible, all appliance connections.

NOTE! Improper care can lead to impairment or even destruction of the unit.

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

15

1. Housing surfaces must be cleaned with a clean, damp cloth. Make sure that no moisture can

penetrate the unit.

2. Air inlets and outlets must be regularly cleaned of dust and dirt. If compressed air is used,

make sure that damage to the unit is prevented (e.g. fans must be blocked in this case).

3. Cables and plug contacts must be cleaned regularly and freed from dust and dirt.

4. In general, no cleaning agents, disinfectants or agents with an abrasive effect may be used

for maintenance, otherwise the surface finish may be impaired. Especially solvents, such as

alcohol, can impair the function of the housing seals.

5. Units should generally be stored in a dry place and protected from dust and dirt.

MAINTENANCE AND REPAIR (BY QUALIFIED PERSONNEL ONLY)

DANGER! There are live components in the unit. Even after disconnecting from the

mains, residual voltage may still be present in the unit, e.g. due to charged capacitors.

NOTE! There are no assemblies in the unit that require maintenance by the user.

NOTE! Maintenance and repair work may only be carried out by specialist personnel

authorised by the manufacturer. In case of doubt, contact the manufacturer.

NOTE! Improperly performed maintenance work can affect the warranty claim.

DIMENSIONS (mm)

142

221

215

43

53

DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

16

TECHNICAL DATA

Item number LDDIO04

Product type 0x4 I/O Dante Interface

Inputs 0

Input type Switchable balanced mic or line level

Line outputs 4

Output type Balanced line level with auto mute relay on loss of Dante/AES67 signal

Cooling Convection

Analogue Line Output

Number of output connectors 4

Connection type 3-pin terminal block, Pitch 3.81 mm

Max. Output Level 18 dBu

Interm. Distortion SMPTE < 0.005 % (-20 dBFS to 0 dBFS)

THD + Noise < 0.002% (10 dBu, 20 kHz BW)

Idle Noise Better than -92dBu

Dynamic Range > 107 dB (0 dBFS, AES 17, CCIR-2k Weighting)

Frequency response 15 Hz – 20 kHz (-0.5 dB)

Dante® Specications

Audio Channels 4 outputs

Bit depth 24 bit

Sample Rate 48 kHz

Latency Minimum 1ms

Dante Connector 100 BASE-T RJ45

Power over Ethernet (PoE) Specications

Minimum PoE Requirements PoE+ IEEE 802.3at

PSE+Data Capable of powering 1 extra PD unit

Power Input Requirements

Input Voltage 24 V DC

Minimum Current 1.5 A

Power Input Connector Pitch 5.08 mm terminal block (2-pin)

Max power consumption 10 W

Idle power consumption 7.5 W (no signal input)

Power Consumption with

Secondary Port use

22 W

Mains Inrush Current 1.7 A @ 230 V AC

Operating Temperature 0°C – 40°C; < 85% humidity, non condensing

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

17

Item number LDDIO04

General

Material Steel chassis, Plastic front panel

Dimensions (W x H x D) 142 x 53 x 221.7 mm (height with rubber feet)

Weight 1.0 kg

Included Accessories Mounting plates for surface mount applications,

Terminal blocks for Electrical Connections, rubber feet

DISPOSAL

Packaging:

1. Packaging can be disposed of via the usual waste disposal channels.

2. Please separate the packaging according to the waste disposal and materials

regulations in your country.

Device:

1. This device is subject to the European Directive on Waste Electrical and Electronic

Equipment in its applicable version. WEEE Directive-Waste Electrical and Electronical

Equipment. Old devices and batteries do not belong in household waste. The old

device or batteries must be disposed of via an approved waste disposal service or

a municipal waste disposal facility. Follow the directives in your country!

2. Follow the disposal laws in your country.

3. As a private customer, you can obtain information on environmentally friendly

disposal options from the retailer from whom you purchased the product or from

the relevant regional authorities.

DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

18

MANUFACTURER´S DECLARATIONS

MANUFACTURER‘S WARRANTY & LIMITATIONS OF LIABILITY

Adam Hall GmbH, Adam-Hall-Str. 1, D-61267 Neu Anspach / E-mail [email protected] /

+49 (0)6081 / 9419-0.

Our current warranty conditions and limitation of liability can be found at:

https://cdn-shop.adamhall.com/media/pdf/MANUFACTURERS-DECLARATIONS_LD_SYSTEMS.pdf.

Contact your distribution partner for service.

UKCA-CONFORMITY

Hereby, Adam Hall Ltd. declares that this product meets the following guidelines

(where applicable):

Electrical Equipment (Safety) Regulations 2016

Electromagnetic Compatibility Regulations 2016 (SI 2016/1091)

The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment

Regulation 2012 (SI 2012/3032)

Radio Equipment Regulations 201 7(SI 2016/2015)

UKCA-DECLARATION OF CONFORMITY

Products that are subject to Electrical Equipment(Safety)Regulation 2016, EMC Regulation 2016 or

RoHS Regulation can be requested at [email protected].

Products that are subject to the Radio Equipments Regulations 2017

(SI2017/1206) can be downloaded from www.adamhall.com/compliance/

CE CONFORMITY

Adam Hall GmbH hereby confirm that this product meets the following guidelines

(where applicable):

R&TTE (1999/5/EC) or RED (2014/53/EU) as of June 2017.

Low Voltage Directive (2014/35/EU)

EMC Directive (2014/30/EU)

RoHS (2011/65/EU)

The complete Declaration of Conformity can be found at www.adamhall.com.

Furthermore, you can also request it at [email protected].

CE DECLARATION OF CONFORMITY

Declarations of conformity for products subject to the LVD, EMC, RoHS Directive

can be requested from [email protected].

Declarations of conformity for products subject to RED Directive

can be downloaded from www.adamhall.com/compliance/.

Subject to misprints and errors, as well as technical or other modifications!

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

19

DEUTSCH

SIE HABEN DIE RICHTIGE WAHL GETROFFEN!

Dieses Gerät wurde unter hohen Qualitätsanforderungen entwickelt und gefertigt, um viele

Jahre einen reibungslosen Betrieb zu gewährleisten. Dafür steht LD Systems mit seinem Namen

und der langjährigen Erfahrung als Hersteller hochwertiger Audioprodukte. Bitte lesen Sie diese

Bedienungsanleitung sorgfältig, damit Sie Ihr neues Produkt von LD Systems schnell optimal

einsetzen können.

Mehr Informationen zu LD Systems finden Sie auf unserer Internetseite WWW.LD-SYSTEMS.COM

INFORMATIONEN ZU DIESER BEDIENUNGSANLEITUNG

• Lesen Sie vor Inbetriebnahme die Sicherheitshinweise und die gesamte Anleitung

aufmerksam durch.

• Beachten Sie die Warnungen auf dem Gerät und in der Bedienungsanleitung.

• Bewahren Sie die Bedienungsanleitung immer in Reichweite auf.

• Wenn Sie das Gerät verkaufen oder weitergeben, händigen Sie unbedingt auch diese

Bedienungs anleitung aus, da sie ein wesentlicher Bestandteil des Produkts ist.

BESTIMMUNGSGEMÄSSER GEBRAUCH

Bei dem Produkt handelt es sich um ein Gerät für professionelle Audioinstallation!

Das Produkt ist für den professionellen Einsatz im Bereich der Audioinstallation entwickelt

worden und ist nicht für die Verwendung in Haushalten vorgesehen!

Weiterhin ist dieses Produkt zur Installation durch qualifizierte Personen mit Fachkenntnissen,

sowie zur Bedienung durch unterwiesene Personen vorgesehen!

Die Benutzung des Produkts außerhalb der spezifizierten technischen Daten und Betriebs-

bedingungen gilt als nicht bestimmungsgemäß!

Haftung für Schäden und Drittschäden an Personen und Sachen durch nicht bestimmungs-

gemäßen Gebrauch ist ausgeschlossen!

Das Produkt ist nicht geeignet für:

– Personen (einschließlich Kinder) mit eingeschränkten körperlichen, sensorischen oder

geistigen Fähigkeiten oder mangelnder Erfahrung und Kenntnis.

– Kinder (Kinder müssen angewiesen werden, nicht mit dem Gerät zu spielen).

BEGRIFFS- UND SYMBOLERKLÄRUNGEN

1. GEFAHR: Mit dem Wort GEFAHR, evtl. in Kombination mit einem Symbol, wird auf unmittelbar

gefährliche Situationen oder Zustände für Leib und Leben hingewiesen.

2. WARNUNG: Mit dem Wort WARNUNG, evtl. in Kombination mit einem Symbol, wird auf potentiell

gefährliche Situationen oder Zustände für Leib und Leben hingewiesen.

3. VORSICHT: Mit dem Wort VORSICHT, evtl. in Kombination mit einem Symbol, wird auf Situationen

oder Zustände hingewiesen, die zu Verletzungen führen können.

4. ACHTUNG: Mit dem Wort ACHTUNG, evtl. in Kombination mit einem Symbol, wird auf Situationen

oder Zustände hingewiesen, die zu Sach- und/oder Umweltschäden führen können.

DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

20

Dieses Symbol kennzeichnet Gefahren, die einen elektrischen Schlag verursachen können.

Dieses Symbol kennzeichnet Gefahrenstellen oder gefährliche Situationen.

Dieses Symbol kennzeichnet Gefahren durch heiße Oberflächen.

Dieses Symbol kennzeichnet Gefahren durch hohe Lautstärken.

Dieses Symbol kennzeichnet ergänzende Informationen zur Bedienung des Produkts.

Dieses Symbol kennzeichnet ein Gerät, in dem sich keine vom Benutzer austauschbaren

Teile befinden.

Dieses Symbol kennzeichnet ein Gerät, das nur in trockenen Räumen verwendet

werden darf.

SICHERHEITSHINWEISE

GEFAHR:

1. Öffnen Sie das Gerät nicht und verändern Sie es nicht.

2. Wenn Ihr Gerät nicht mehr ordnungsgemäß funktioniert, Flüssigkeiten oder Gegen-

stände in das Geräteinnere gelangt sind, oder das Gerät anderweitig beschädigt

wurde, schalten Sie es sofort aus und trennen es von der Spannungsversorgung.

Dieses Gerät darf nur von autorisiertem Fachpersonal repariert werden.

3. Bei Geräten der Schutzklasse 1 muss der Schutzleiter korrekt angeschlossen

werden. Unterbrechen Sie niemals den Schutzleiter. Geräte der Schutzklasse 2

haben keinen Schutzleiter.

4. Sorgen Sie dafür, dass spannungsführende Kabel nicht geknickt oder anderweitig

mechanisch beschädigt werden.

5. Überbrücken Sie niemals die Gerätesicherung.

WARNUNG:

1. Das Gerät darf nicht in Betrieb genommen werden, wenn es offensichtliche

Beschädigungen aufweist.

2. Das Gerät darf nur im spannungsfreien Zustand installiert werden.

3. Wenn das Netzkabel des Geräts beschädigt ist, darf das Gerät nicht in Betrieb

genommen werden.

4. Fest angeschlossene Netzleitungen dürfen nur von einer qualifizierten Person

ersetzt werden.

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

La pagina sta caricando ...

LD Systems DIO 04 Manuale utente

LD Systems DIO 04 Manuale utente

in altre lingue

Documenti correlati

Altri documenti