USE iPod/iPhone WITH A WIRELESS DOCK CRADLE FOR iPod/iPhone
(Sold Separately (HT-WDC10))
You can enjoy finer quality of music through the speaker by sending iPod/iPhone’s audio signal using a
Wireless Transmitter.
To link the main unit with wireless transmitter, you have to make ID setting when both main unit and wireless
transmitter are turned on.
Turn on the main unit and connect the iPod/iPhone to the Wireless transmitter.
Then press INPUT SELECT button on the remote control to select "W iPod" mode.
The INPUT SELECT mode of the main unit will switches as follows.
Repeatedly press DIGI.1
➡
DIGI.2
➡
ANALOG
➡
W iPod
(See page 18)
The Sound bar will not be turned off if iPod/iPhone is not connected to the Wireless Transmitter.
For more information on HT-WDC10, refer to the HT-WDC10’s user manual.
“Made for iPod,” and “Made for iPhone” mean that an electronic ▪
accessory has been designed to connect specifically to iPod or
iPhone, respectively, and has been certified by the developer to
meet Apple performance standards. Apple is not responsible for the operation of this device
or its compliance with safety and regulatory standards. Please note that the use of this
accessory with iPod or iPhone may affect wireless performance.
iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered ▪
in the U.S. and other countries.
The volume control may not be operated normally except at the referred models. If there is any error ▪
happened at the models above, please update the software of iPod/iPhone at the lastest version.
iPod/iPhone MODELS THAT CAN BE USED WITH THIS PRODUCT
iPod touch
(1st, 2nd, 3rd, and 4th
generation)
iPod classic iPod with video
iPod nano
(1st, 2nd, 3rd, 4th, 5th,
and 6th generation)
iPhone 4 iPhone 3GS
iPhone 3G iPhone
1. Turn off your Home Theater (HW-D450, HW-D451).
2.
Press the hold "3D SOUND" button on the remote control for 5
seconds. The standby light on the HW-D450, HW-D451 will blink once.
3. Connect the iPod/iPhone to the Wireless transmitter.
4. Turn on the iPod/iPhone. Press the "ID SET" button on the back
of the Wireless transmitter for 5 seconds. The link light on the
wireless transmitter will blink fast.
5.
Turn on your Home Theater(make sure the wireless transmitter's Link
LED in ON). To listen to music from your iPod/iPhone over the Home
Theater, select the iPod mode as the Home Theater's source.
You can control the speaker volume of iPod/iPhone with a •
volume wheel or a volume bar.
When iPod/iPhone is stopped or in a power saving mode, a •
Wireless transmitter is turned to the Sleep Mode.
When iPod/iPhone is turned to the Deep Sleep Mode, the
Wireless transmitter is off.
HOW TO LINK THE WIRELESS TRANSMITTER WITH THE MAIN UNIT
Set an ID of the Subwoofer before setting a Transmitter ID. ( See page 12 )
POWER
TV POWER
AUDIO
MUTE
TV INFO
AUTO
POWER
A V SYNC
AH59-02330A
VOL
TV
CH
SOUND
MODE
3D
SOUND
S.VOL
INPUT
SELECT
DIMMER
S/W LEVEL
HDMISPK CONTROL
DRC
POWER
TV POWER
AUDIO
MUTE
TV INFO
AUTO
POWER
A V SYNC
AH59-02330A
VOL
TV
CH
SOUND
MODE
3D
SOUND
S.VOL
INPUT
SELECT
DIMMER
S/W LEVEL
HDMISPK CONTROL
DRC
If you use the main unit nearby a wireless device such as a laptop computer, an AP, or Wifi,
▪
any unstable operation error can happen.
Do not pairing the subwoofer and iPod/iPhone at the same time. If you pairing at the same
▪
time, iPod/iPhone and subwoofer may not connect to the Sound bar.