Hotpoint UIF 9.3F LB X Guida utente

Categoria
Cappe da cucina
Tipo
Guida utente
IT EN DE
Italiano, 12 English, 15 Deutsch, 18
FR NL ES
Français, 21 Nederlands, 24 Español, 27
PT RU UK
Português, 30
РУССКИЙ, 33 Українська, 36
KK PL CS
Kazakh, 39
Polski, 42
Český, 45
SK HU
Slovenský, 48 Magyar, 51
UIF 9.3F LB X
Istruzioni per l’uso
Instructions for use
Betriebsanleitung
Mode d’emploi
Gebruiksaanwijzingen
Instrucciones de uso
Instruções de uso
Инструкция по
зксплуатации
Інструкції з
використання
Пайдалану нұсқауы
Instrukcja obsługi
Návod k použití
Návod na používanie
Használati útmutató
2
3
4
5
6
7
8
9
10
11
Italiano
12
IT
SICUREZZA GENERALE
• Prima di qualsiasi operazione di pulizia o
manutenzione, disinserire la cappa dalla rete elettrica
togliendo la spina o staccando l’interruttore generale
dell’abitazione.
• Per tutte le operazioni di installazione e
manutenzione utilizzare guanti da lavoro.
• L’apparecchio può essere utilizzato da bambini di
età non inferiore a 8 anni e da persone con ridotte
capacità fisiche, sensoriali o mentali, o prive di
esperienza o della necessaria conoscenza, purchè
sotto sorveglianza oppure dopo che le stesse abbiano
ricevuto istruzioni relative all’uso sicuro
dell’apparecchio e alla comprensione dei pericoli ad
esso inerenti.
• I bambini devono essere controllati affinché non
giochino con l’apparecchio.
• La pulizia e la manutenzione non deve essere
effettuata da bambini senza sorveglianza.
• Il locale deve disporre di sufficiente ventilazione,
quando la cappa da cucina viene utilizzata
contemporaneamente ad altri apparecchi a
combustione di gas o altri combustibili.
• La cappa va frequentemente pulita sia internamente
che esternamente (ALMENO UNA VOLTA AL
MESE), rispettare comunque quanto espressamente
indicato nelle istruzioni di manutenzione.
L’inosservanza delle norme di pulizia della cappa e
della sostituzione e pulizia dei filtri comporta rischi di
incendi.
• E’ severamente vietato fare cibi alla fiamma sotto la
cappa.
• Per la sostituzione della lampada utilizzare solo il
tipo lampada indicato nella sezione manutenzione
/sostituzione lampada di questo manuale.
L’impiego di fiamma libera è dannoso ai filtri e può
dar luogo ad incendi, pertanto deve essere evitato in
ogni caso.
La frittura deve essere fatta sotto controllo onde
evitare che l’olio surriscaldato prenda fuoco.
ATTENZIONE: Quando il piano di cottura è in
funzione le parti accessibili della cappa possono
diventare calde.
Non collegare l’apparecchio alla rete elettrica finche
l’installazione non è totalmente completata.
Per quanto riguarda le misure tecniche e di sicurezza da adottare per lo scarico
dei fumi attenersi strettamente a quanto previsto dai regolamenti delle autorità
locali competenti.
L’aria aspirata non deve essere convogliata in un condotto usato per lo scarico
dei fumi prodotti da apparecchi a combustione di gas o di altri combustibili.
Non utilizzare o lasciare la cappa priva di lampade correttamente montate per
possibile rischio di scossa elettrica.
Mai utilizzare la cappa senza griglia correttamente montata!
La cappa non va MAI utilizzata come piano di appoggio a meno che non sia
espressamente indicato.
Utilizzare solo le viti di fissaggio in dotazione con il prodotto per l'installazione
o, se non in dotazione, acquistare il tipo di viti corretto.
Utilizzare la lunghezza corretta per le viti che sono identificati nella Guida
all'installazione.
In caso di dubbio, consultare il centro di assistenza autorizzato o personale
qualificato similare.
ATTENZIONE!
La mancata installazione di viti e dispositivi di fissaggio in conformità di
queste istruzioni può comportare rischi di natura elettrica.
Non utilizzare con un programmatore, timer, telecomando separato o
qualsiasi altro dispositivo che si attiva automaticamente.
La cappa può avere estetiche differenti rispetto a quanto illustrato nei
disegni di questo libretto, comunque le istruzioni per l'uso, la
manutenzione e l'installazione rimangono le stesse.
Attenersi strettamente alle istruzioni riportate in questo manuale. Si declina
ogni responsabilità per eventuali inconvenienti, danni o incendi provocati
all'apparecchio derivati dall'inosservanza delle istruzioni riportate in questo
manuale. La cappa è concepita per l'aspirazione dei fumi e vapori della cottura
ed è destinata al solo uso domestico.
E' importante conservare tutti i manuali che accompagnano il prodotto per
poterli consultare in ogni momento. In caso di vendita, di cessione o di
trasloco, assicurarsi che restino insieme al prodotto.
Leggere attentamente le istruzioni: ci sono importanti informazioni
sull'installazione, sull'uso e sulla sicurezza.
Non effettuare variazioni elettriche o meccaniche sul prodotto o sulle
condotte di scarico.
Verificare l'integrità della cappa prima di procedere con l’installazione. In
caso contrario contattare il rivenditore e non proseguire con l'installazione.
La distanza minima fra la superficie di supporto dei recipienti sul dispositivo di
cottura e la parte più bassa della cappa da cucina deve essere non inferiore a 50
cm in caso di cucine elettriche e di 65 cmin caso di cucine a gas o miste.
Se le istruzioni di installazione del dispositivo di cottura a gas specificano una
distanza maggiore, bisogna tenerne conto.
COLLEGAMENTO ELETTRICO
La tensione di rete deve corrispondere alla tensione riportata sull’etichetta
caratteristiche situata all’interno della cappa. Se provvista di spina allacciare la
cappa ad una presa conforme alle norme vigenti posta in zona accessibile anche
dopo l’installazione. Se sprovvista di spina (collegamento diretto alla rete) o la
spina non è posta in zona accessibile, anche dopo installazione, applicare un
interruttore bipolare a norma che assicuri la disconnessione completa della rete
nelle condizioni della categoria di sovratensione III, conformemente alle regole di
installazione.
ATTENZIONE!
Prima di ricollegare il circuito della cappa all’alimentazione di rete e di verificarne
il corretto funzionamento, controllare sempre che il cavo di rete sia stato montato
correttamente.
Sostituzione del cavo di alimentazione
La cappa è provvista di un cavo alimentazione speciale; in caso di
danneggiamento del cavo, richiederlo al servizio assistenza tecnica.
SCARICO DELL' ARIA
(per le versioni aspiranti)
Collegare la cappa a tubi e fori di scarico a parete con diametro equivalente
all'uscita d'aria (flangia di raccordo).
L'utilizzo di tubi e fori di scarico a parete con diametro inferiore determinerà una
diminuizione delle prestazioni di aspirazione ed un drastico aumento della
rumorosità.
13
Si declina perciò ogni responsabilità in merito.
! Usare un condotto lungo il minimo indispensabile.
! Usare un condotto con minor numero di curve possibile (angolo massimo
della curva: 90°).
! Evitare cambiamenti drastici di sezione del condotto.
! L'azienda declina ogni responsabilità qualora queste norme non vengano
rispettate.
FILTRANTE O ASPIRANTE ?
! La vostra cappa è pronta per essere utilizzata in versione aspirante.
Per utilizzare la cappa in versione filtrante va installato l’apposito KIT
ACCESSORIO.
Verificate nelle prime pagine di questo manuale se il KIT ACCESSORIO è
già fornito a corredo o va acquistato a parte.
Nota: Se fornito a corredo, in alcuni casi, il sistema di filtraggio aggiuntivo a
base di carboni attivi potrebbe essere già installato sulla cappa.
Le informazioni per la trasformazione della cappa da versione aspirante a
versione filtrante sono già contenute in questo manuale.
Versione aspirante
I vapori vengono evacuati verso l’esterno tramite un tubo di scarico fissato alla
flangia di raccordo.
ATTENZIONE!
Il tubo di evacuazione non è fornito e va acquistato.
Il diametro del tubo di scarico deve essere equivalente al diametro dell'anello di
connessione.
ATTENZIONE!
Se la cappa è provvista di filtro/i a carbone, questo/i deve/devono essere
rimosso/i.
Versione filtrante
L’aria aspirata verrà sgrassata e deodorata prima di essere riconvogliata nella
stanza. Per utilizzare la cappa in questa versione è necessario installare un
sistema di filtraggio aggiuntivo a base di carboni attivi.
COMANDI
La cappa è fornita di un pannello comandi con un controllo delle velocità di
aspirazione ed un controllo di accensione della luce per l'illuminazione del piano
di cottura.
T1. Tasto ON/OFF motore di aspirazione
T2. Tasto di selezione velocità (potenza) di aspirazione di esercizio
Nota: La velocità (potenza) di aspirazione intensiva (LED L3 lampeggiante)
ha una durata di circa 5 minuti, dopodichè viene impostata
automaticamente la velocità (potenza) di aspirazione media (LED L2
acceso)
T3. Tasto ON/OFF illuminazione
T4. Tasto di selezione velocità (potenza) di aspirazione "silenziosa"
L1. LED velocità (potenza) di aspirazione media
L2. LED velocità (potenza) di aspirazione alta
L3 LED velocità (potenza) di aspirazione intensiva - temporizzata (5 min.).
L4 LED di saturazione dei filtri:
lampeggiante: eseguire la manutenzione del filtro al carbone.
acceso: eseguire la manutenzione dei filtri grassi.
L5 LED velocità (potenza) di aspirazione bassa (silenziosa)
L1+L2+L3 lampeggianti in sequenza: funzionamento automatico in presenza
di temperatura elevata (vei paragrafo relativo)
Reset saturazione filtri
Dopo aver eseguito la manutenzione dei filtri premere a lungo il tasto T1, il LED
L4 si spegne.
Attivazione LED saturazione filtro carbone
Il LED della saturazione filtro carbone è normalmente disattivato. Per
attivarlo procedere come segue:
A cappa spenta premere e mantenere premuto a lungo e
contemporaneamente T1 e T4: prima lampeggia L1 poi anche L2 ad
indicare l'avvenuta attivazione.
Disattivazione LED saturazione filtro carbone: ripetere l'operazione
sopra descritta, prima lampeggiano L1 e L2 poi solo L1 ad indicare
l'avvenuta disattivazione.
Funzionamento automatico in presenza di temperatura elevata
La cappa è dotata di un sensore che rileva la temperatura. Quando questa
diventa troppo elevata, il sensore fa attivare automaticamente la velocità
(potenza) di aspirazione media. La cappa si spegne non appena la temperatura
rilevata dal sensore si abbassa sensibilmente.
MANUTENZIONE
Pulizia
Per la pulizia usare ESCLUSIVAMENTE un panno inumidito con detersivi liquidi
neutri. NON UTILIZZARE UTENSILI O STRUMENTI PER LA PULIZIA!
Evitare l’uso di prodotti contenenti abrasivi. NON UTILIZZARE ALCOOL!
Pannello di aspirazione perimetrale
Pulire il pannello di aspirazione perimetrale con la stessa frequenza del filtro
antigrasso, usare un panno ed un detergente liquido non troppo concentrato.
Non utilizzare mai sostanze abrasive.
Manutenzione dei filtri antigrasso
Trattiene le particelle di grasso derivanti dalla cottura.
Deve essere pulito una volta al mese (o quando il sistema di indicazione di
saturazione dei filtri - se previsto sul modello in possesso- indica questa
necessità), con detergenti non aggressivi, manualmente oppure in lavastoviglie a
basse temperature ed a ciclo breve.
Con il lavaggio in lavastoviglie il filtro antigrasso metallico può scolorirsi ma le
sue caratteristiche di filtraggio non cambiano assolutamente.
Per smontare il filtro grassi tirare la maniglia di sgancio a molla.
14
Manutenzione del filtro al carbone
Trattiene gli odori sgradevoli derivanti dalla cottura.
La saturazione del filtro carbone si verifica dopo un uso più o meno prolungato a
seconda del tipo di cucina e della regolarità della pulizia del filtro grassi. In ogni
caso è necessario sostituire la cartuccia al massimo ogni quattro mesi (o quando
il sistema di indicazione di saturazione dei filtri - se previsto sul modello in
possesso- indica questa necessità).
NON può essere lavato o rigenerato
Montaggio
Agganciare il filtro ai carboni attivi prima posteriormente sulla linguetta metallica
della cappa, poi anteriormente con i due pomelli.
Smontaggio
Rimuovere il filtro ai carboni attivi girando di 90° i pomelli che lo fissano alla
cappa.
Sostituzione delle lampade
La cappa è dotata di un sistema di illuminazione basato sulla tecnologia LED.
I LED garantiscono una illuminazione ottimale, una durata fino a 10 volte
maggiore delle lampade tradizionali e consentono di risparmiare il 90% di
energia elettrica.
Per la sostituzione rivolgersi al servizio assistenza tecnica.
SMALTIMENTO
Questo apparecchio è contrassegnato in conformità alla Direttiva Europea
2012/19/EC, Waste Electrical and Electronic Equipment (WEEE). Assicurandosi
che questo prodotto sia smaltito in modo corretto, l'utente contribuisce a
prevenire le potenziali conseguenze negative per l'ambiente e la salute.
Il simbolo
sul prodotto o sulla documentazione di accompagnamento
indica che questo prodotto non deve essere trattato come rifiuto domestico ma
deve essere consegnato presso l'idoneo punto di raccolta per il riciclaggio di
apparecchiature elettriche ed elettroniche. Disfarsene seguendo le normative
locali per lo smaltimento dei rifiuti. Per ulteriori informazioni sul trattamento,
recupero e riciclaggio di questo prodotto, contattare l'idoneo ufficio locale, il
servizio di raccolta dei rifiuti domestici o il negozio presso il quale il prodotto è
stato acquistato.
Apparecchiatura progettata, testata e realizzata nel rispetto delle norme sulla:
• Sicurezza: EN/IEC 60335-1; EN/IEC 60335-2-31, EN/IEC 62233.
• Prestazione: EN/IEC 61591; ISO 5167-1; ISO 5167-3; ISO 5168; EN/IEC
60704-1; EN/IEC 60704-2-13; EN/IEC 60704-3; ISO 3741; EN 50564; IEC
62301.
• EMC: EN 55014-1; CISPR 14-1; EN 55014-2; CISPR 14-2; EN/IEC 61000-3-2;
EN/IEC 61000-3-3. Suggerimenti per un corretto utilizzo al fine di ridurre
l’impatto ambientale: Quando iniziate a cucinare, accendere la cappa alla
velocità minima, lasciandola accesa per alcuni minuti anche dopo il termine della
cottura. Aumentare la velocità solo in caso di grandi quantità di fumo e vapore,
utilizzando la funzione booster solo in casi estremi. Per mantenere ben efficiente
il sistema di riduzione degli odori, sostituire, quando è necessario, il/i filtro/i
carbone. Per mantenere ben efficiente il filtro del grasso, pulirlo in caso di
necessità. Per ottimizzare l’efficienza e minimizzare i rumori, utilizzare il diametro
massimo del sistema di canalizzazione indicato in questo manuale.
ANOMALIE DI FUNZIONAMENTO
Se qualcosa non sembra funzionare, prima di chiamare il Servizio Assistenza
effettuare i seguenti semplici controlli:
Se la cappa non funziona:
Verificare che:
- non c’è interruzione di corrente.
- è stata selezionata una velocità.
Se la cappa ha un rendimento scarso:
Verificare che:
- La velocità motore selezionata è sufficiente per la quantità di fumo e di
vapori liberata.
- La cucina è sufficientemente areata per permettere una presa d’aria.
- Il filtro carbone non è consumato (cappa in versione filtrante).
Se la cappa si è spenta nel corso del normale funzionamento:
Verificare che:
- non c’è interruzione di corrente.
- il dispositivo di interruzione omnipolare non è scattato.
In caso di eventuali anomalie di funzionamento, prima di rivolgerVi al servizio
assistenza scollegate per almeno 5 sec. l’apparecchio dall’alimentazione
elettrica estraendo la spina e collegatelo poi nuovamente. Nel caso in cui
l’anomalia di funzionamento dovesse perdurare, rivolgersi al servizio
d’assistenza.
DATI TECNICI
Modello
Altezza
(cm)
Larghezza
(cm)
Profondità
(cm)
Ø del tubo
di scarico
(cm)
HIF 9.3F LB X
HIGC 9.3F LB X
60,9 – 113
72,2 –113
89,8 59,8 15-12,5-12
Vedi targhetta caratteristiche per l'assorbimento totale e l'assorbimento della
lampada.
Componenti non in dotazione con il prodotto
English
15
EN
GENERAL SAFETY
• Before any cleaning or maintenance operation,
disconnect hood from the mains by removing the plug
or disconnecting the mains electrical supply.
• Always wear work gloves for all installation and
maintenance operations.
• This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
• Children shall not be allowed to tamper with the
controls or play with the appliance.
• Cleaning and user maintenance shall not be made
by children without supervision.
• The premises where the appliance is installed must
be sufficiently ventilated, when the kitchen hood is
used together with other gas combustion devices or
other fuels.
• The hood must be regularly cleaned on both the
inside and outside (AT LEAST ONCE A MONTH).
• This must be completed in accordance with the
maintenance instructions provided. Failure to follow
the instructions provided regarding the cleaning of the
hood and filters will lead to the risk of fires.
• Do not flambé under the range hood.
• For lamp replacement use only lamp type indicated
in the Maintenance/Replacing lamps section of this
manual.
The use of exposed flames is detrimental to the filters
and may cause a fire risk, and must therefore be
avoided in all circumstances.
Any frying must be done with care in order to make
sure that the oil does not overheat and ignite.
CAUTION: Accessible parts of the hood may become
hot when used with cooking appliances.
• Do not connect the appliance to the mains until the
installation is fully complete.
• With regards to the technical and safety measures to be adopted for fume
discharging it is important to closely follow the regulations provided by the local
authorities.
• The air must not be discharged into a flue that is used for exhausting fumes
from appliance burning gas or other fuels.
• Do not use or leave the hood without the lamp correctly mounted due to the
possible risk of electric shocks.
• Never use the hood without effectively mounted grids.
• The hood must NEVER be used as a support surface unless specifically
indicated.
• Use only the fixing screws supplied with the product for installation or, if not
supplied, purchase the correct screws type.
• Use the correct length for the screws which are identified in the Installation
Guide.
• In case of doubt, consult an authorized service assistance center or similar
qualified person.
WARNING!
• Failure to install the screws or fixing device in accordance with these
instructions may result in electrical hazards.
Do not use with a programmer, timer, separate remote control system or
any other device that switches on automatically.
The hood can look different to that illustrated in the drawings in this
booklet. The instructions for use, maintenance and installation, however,
remain the same.
Closely follow the instructions set out in this manual. All responsibility, for
any eventual inconveniences, damages or fires caused by not complying with the
instructions in this manual, is declined. This appliance is intended to be used in
household and similar application such as: - staff kitchen areas in shop, offices
and other working environments; - farm houses; - by clients in hotels, motels and
other residential type environments; - bed and breakfast type environments.
It is important to conserve this booklet for consultation at any moment. In
the case of sale, cession or move, make sure it is together with the product.
Read the instructions carefully: there is important information about
installation, use and safety.
Do not carry out electrical or mechanical variations on the product or on the
discharge conduits.
Before proceeding with the installation of the appliance verify that there are
no damaged all components. Otherwise contact your dealer and do not
proceed with the installation.
The minimum distance between the supporting surface for the cooking
equipment on the hob and the lowest part of the range hood must be not less
than 50cm from electric cookers and 65cm from gas or mixed cookers.
If the instructions for installation for the gas hob specify a greater distance, this
must be adhered to.
ELECTRICAL CONNECTION
The mains power supply must correspond to the rating indicated on the plate
situated inside the hood. If provided with a plug connect the hood to a socket in
compliance with current regulations and positioned in an accessible area, after
installation. If it not fitted with a plug (direct mains connection) or if the plug is not
located in an accessible area, after installation, apply a double pole switch in
accordance with standards which assures the complete disconnection of the
mains under conditions relating to over-current category III, in accordance with
installation instructions.
WARNING!
Before re-connecting the hood circuit to the mains supply and checking the
efficient function, always check that the mains cable is correctly assembled.
Replacing the power cable
The hood is provided with a special power cable ; if the cable is damaged,
request a new one from Technical Service.
AIR VENT
(for the suction versions)
Connect the hood and discharge holes on the walls with a diameter equivalent to
the air outlet (connection flange).
Using the tubes and discharge holes on walls with smaller dimensions will cause
a diminution of the suction performance and a drastic increase in noise.
Any responsibility in the matter is therefore declined.
! Use a duct of the minimum indispensable length.
! Use a duct with as few elbows as possible (maximum elbow angle: 90°).
! Avoid drastic changes in the duct cross-section.
! The company declines any responsibility whenever these regulations are
not respected.
FILTERING OR DUCTING ?
! Your cooker hood is ready to be used in suction version.
To use the hood in filtering version the special ACCESSORY KIT must be
16
installed.
Check on the first pages of this manual if the ACCESSORY KIT is furnished
or must be bought separately.
Note: If furnished, in certain cases, the additional activated carbon filtering
system may be installed on the hood.
Information about the conversion of the hood from suction version to filtering
version is present in this manual.
Ducting version
In this case the fumes are conveyed outside of the building by means of a
special pipe connected with the connection ring located on top of the hood.
CAUTION!
The exhausting pipe is not supplied and must be purchased apart.
Diameter of the exhausting pipe must be equal to that of the connection ring.
CAUTION!
If the hood is supplied with active charcoal filter, then it must be removed.
Filter version
The aspirated air will be degreased and deodorised before being fed back into
the room.
In order to use the hood in this version, you have to install a system of additional
filtering based on activated charcoal.
CONTROLS
The hood is fitted with a control panel with aspiration speed selection control and
a light switch to control cooking area lights.
T1. Button ON/OFF suction motor
T2. Selection button operating suction speed (power)
Note: The intensive suction speed (power) (LED L3 flashing) lasts for
approximately 5 minutes, then the medium suction speed (power) is
automatically set (LED L2 on)
T3. Button ON/OFF lighting
T4. Selection button ‘silent’ suction speed (power)
L1. LED medium suction speed (power)
L2. LED high suction speed (power)
L3 LED intensive suction speed (power) - timed (5 min.).
L4 LED filter saturation:
flashing: carry out maintenance of the charcoal filter;
on: carry out maintenance of grease filters.
L5 LED low (silent) suction speed (power)
L1+L2+L3 flashing in sequence: automatic operation at high temperature (see
related section)
Reset filter saturation
After carrying out filter maintenance, press and hold button T1, LED L4 switches
off.
Activation of the LED for charcoal filter saturation
The LED for charcoal filter saturation is normally disabled. To activate it,
proceed as follows:
With the hood off, press and hold for a long time and simultaneously T1 and
T4: L1 flashes first then L2 as well, to indicate successful activation.
Disabling the LED for charcoal filter saturation: repeat the above
operation, L1 and L2 start flashing first, then only L1, to indicate successful
disabling.
Automatic operation at high temperature
The hood is fitted with a sensor that detects the temperature. When this
becomes too high, the sensor automatically activates the medium suction speed
(power). The hood switches off when the temperature detected by the sensor
has lowered significantly.
MAINTENANCE
Cleaning
Clean using ONLY a cloth dampened with neutral liquid detergent. DO NOT
CLEAN WITH TOOLS OR INSTRUMENTS. Do not use abrasive products. DO
NOT USE ALCOHOL!
Perimeter aspiration panel
Clean the perimeter aspiration panel with the same frequency as the ant-fats
filter, using a cloth and not too concentrated liquid detergent. Do not use
abrasive substances.
Maintenance of the anti-grease filters
Traps cooking grease particles.
This must be cleaned once a month (or when the filter saturation indication
system – if envisaged on the model in possession – indicates this necessity)
using non aggressive detergents, either by hand or in the dishwasher, which
must be set to a low temperature and a short cycle.
When washed in a dishwasher, the grease filter may discolor slightly, but this
does not affect its filtering capacity.
To remove the grease filter, pull the spring release handle.
Maintenance of the charcoal filter
It absorbs unpleasant odors caused by cooking.
The saturation of the charcoal filter occurs after more or less prolonged use,
depending on the type of cooking and the regularity of cleaning of the grease
filter.
In any case it is necessary to replace the cartridge at least every four mounths
(or when the filter saturation indication system – if envisaged on the model in
possession – indicates this necessity).The charcoal filter may NOT be washed or
regenerated.
Assembly
Hook the charcoal filter at the back on the metal tongue of the hood first, then on
the front with the two knobs.
Disassembly
Remove the charcoal filter by turning the knobs fixing it to the hood by 90°.
17
Replacing lamps
The hood is equipped with a lighting system based on LED technology.
The LEDs guarantee an optimum lighting, a duration up to 10 times as long as
the traditional lamps and allow to save 90% electrical energy.
For replacement, contact the technical service.
DISPOSAL
• This appliance is marked according to the European directive 2012/19/EC on
Waste Electrical and Electronic Equipment (WEEE).
• By ensuring this product is disposed of correctly, you will help prevent potential
negative consequences for the environment and human health, which could
otherwise be caused by inappropriate waste handling of this product.
• The symbol
on the product, or on the documents accompanying the
product, indicates that this appliance may not be treated as household waste.
Instead it should be taken to the appropriate collection point for the recycling of
electrical and electronic equipment. Disposal must be carried out in accordance
with local environmental regulations for waste disposal.
• For further detailed information regarding the process, collection and recycling
of this product, please contact the appropriate department of your local
authorities or the local department for household waste or the shop where you
purchased this product.
Appliance designed, tested and manufactured according to:
• Safety: EN/IEC 60335-1; EN/IEC 60335-2-31, EN/IEC 62233.
• Performance: EN/IEC 61591; ISO 5167-1; ISO 5167-3; ISO 5168; EN/IEC
60704-1; EN/IEC 60704-2-13; EN/IEC 60704-3; ISO 3741; EN 50564; IEC
62301.
• EMC: EN 55014-1; CISPR 14-1; EN 55014-2; CISPR 14-2; EN/IEC 61000-3-2;
EN/IEC 61000-3-3. Suggestions for a correct use in order to reduce the
environmental impact: Switch ON the hood at minimum speed when you start
cooking and kept it running for few minutes after cooking is finished. Increase the
speed only in case of large amount of smoke and vapor and use boost speed(s)
only in extreme situations. Replace the charcoal filter(s) when necessary to
maintain a good odor reduction efficiency. Clean the grease filter(s) when
necessary to maintain a good grease filter efficiency. Use the maximum diameter
of the ducting system indicated in this manual to optimize efficiency and
minimize noise.
MALFUNCTIONS
If something appears not to be working properly, do the following simple checks
before calling Technical Service:
If the hood is not working:
Check that:
- The power has not been disconnected.
- A speed has been selected.
If the hood performs inefficiently:
Check that:
- The motor speed selected is sufficient for the amount of smoke and
vapours released.
- The kitchen is sufficiently ventilated to allow air intake.
- The charcoal filter is not worn (hood in filtering version).
If the hood has turned off during normal functioning:
Check that:
- The power has not been disconnected.
- the omnipolar disconnection device has not tripped.
If the hood fails to operate correctly, briefly disconnect it from the mains power
supply for almost 5 sec. by pulling out the plug. Then plug it in again and try once
more before contacting the Technical Assistance Service.
TECHNICAL DATA
Model
Height
(cm)
Width
(cm)
Tiefe
(cm)
Ø of
exhaust
tube
(cm)
HIF 9.3F LB X
HIGC 9.3F LB X
60,9 – 113
72,2 –113
89,8 59,8 15-12,5-12
Please check the plate in order to verify the total absorption and the light
absorption.
Components not provided with the product
Deutsch
18
DE
ALLGEMEINE SICHERHEIT
• Vor jeglicher Reinigung bzw. Wartung muss das
Gerät vom Stromnetz getrennt werden, indem man
den Stecker herauszieht bzw. den Hauptschalter
ausschaltet.
• Alle Installations-und Wartungarbeiten sind mit
Arbeitshandschuhen durchzuführen.
• Das Gerät kann von Kindern ab 8 Jahren, sowie von
Menschen mit verringerten physischen, sinnlichen
oder psychischen Fähigkeiten (oder ohne Erfahrung
und Kenntnisse) benutzt werden, sofern sie
entsprechend überwacht werden bzw. in die
Benutzung des Geräts sicher eingewiesen wurden
und sich der damit verbundenen Gefahren bewusst
sind.
• Darauf achten, dass Kinder mit dem Gerät nicht
spielen. Kinder dürfen bei Reinigung und Wartung nur
dann helfen, wenn sie dabei beaufsichtigt werden.
• Der Raum muss ausreichend belüftet sein, wenn die
Dunstabzugshaube zusammen mit anderen Gas-
bzw. Brennstoffgeräten verwendet wird.
• Die Dunstabzugshaube muss regelmäßig von innen
und außen gereinigt werden (MINDESTENS EINMAL
IM MONAT), außerdem sollten die Anweisungen zur
Wartung befolgt werden. Das nicht befolgen der
Normen zur Reinigung der Dunstabzugshaube, das
nicht befolgen der Hinweise zur Reinigung und zum
Austausch von Filtern führt zu Brandgefahr.
• Es ist streng verboten, Speisen auf Kochstellen mit
offener Flamme unter der Dunstabzugshaube zu
kochen.
• Für den Lampenersatz verwenden Sie nur den
Lampentyp, der in dem Absatz Lampenwartung /
Ersatz des vorliegenden Handbuchs angegeben wird.
Die Verwendung von offener Flamme schadet den
Filtern und kann zu Brandgefahr führen, daher ist sie
in jedem Fall zu vermeiden.
Das Frittieren muss mit Vorsicht durchgeführt werden,
um zu vermeiden, dass das überhitzte Öl Feuer fängt.
ACHTUNG: Ist das Kochfeld in Betrieb, können
zugängliche Teile der Dunstabzugshaube heiß
werden.
• Das Gerät nicht an das Stromnetz anschließen, bis
die Installation vollständig abgeschlossen ist.
Für das Ableiten der Küchengerüche halten Sie sich an die Voschriften der
örtlichen Behörde halten.
Bei gleichzeitigem Betrieb der Dunstabzugshaube im Abluftbetrieb und gas-
oder brennstoffbetriebenen Geräten darf im Aufstellraum der Geräte der
Unterdruck nicht größer als 4 Pa (4 x 10
-5
bar) sein.
Die Abluft darf nicht in einen Kamin geleitet werden, der zugleich Abgase von
der Verbrennung von Gas oder anderen Brennstoffen führt.
Benutzen Sie die Haube nicht ohne korrekt montierte Lampen, um
Stromschlaggefahr zu vermeiden.
Die Dunstabzugshaube niemals ohne richtig installiertes Gitter verwenden!
Die Dunstabzugshaube darf NIEMALS als Auflagefläche verwendet werden,
sofern es nicht ausdrücklich angegeben ist.
Verwenden Sie nur die mit dem Produkt für die Installation mitgelieferten
Schrauben, oder, falls nicht im Lieferumfang enthalten, kaufen Sie den richtigen
Schraubentyp.
Die Länge für die Schrauben verwenden, die im Installationshandbuch
angegeben wird.
Im Zweifelsfall, fragen Sie Ihren autorisierten Kundendienst oder ein ähnliches
Fachpersonal.
ACHTUNG!
Schrauben und Befestigungselemente, die nicht in Übereinstimmung mit
diesen Hinweisen sind, können zur elektrischen Gefährdung führen.
Nicht mit einem externen Timer, einer Schaltuhr oder einer
Fernbedienung oder jeglicher anderer Vorrichtung, die sich automatisch
aktiviert, verwenden.
Die Dunstabzugshaube kann anders aussehen als auf den Abbildungen in
der vorliegenden Bedienungsanleitung. Die Bedienungsanleitungen, die
Wartung und die Installation sind aber gleich.
Die Anweisungen, die in diesem Handbuch gegeben werden, müssen strikt
eingehalten werden. Es wird keinerlei Haftung übernommen für mögliche
Mängel, Schäden oder Brände der Dunstabzugshaube, die auf die
Nichtbeachtung der Vorschriften in diesem Handbuch zurückzuführen sind. Die
Dunstabzugshaube wurde für die Absaugung der beim Kochen entstehenden
Dünste und Dämpfe entwickelt. Sie ist nur für den Hausgebrauch geeignet.
Die Bedienungsanleitung muss aufbewahrt werden, damit jederzeit ein
Nachschlagen möglich ist. Bei Verkauf, Abtretung oder Umzug muss die
Bedienungsanleitung immer beim Produkt bleiben.
Die Bedienungsanleitung muss aufmerksam gelesen werden, da sie
wichtige Informationen über Installation, Gebrauch und Sicherheit enthält.
Es dürfen keine elektrischen oder mechanischen Änderungen am Gerät
oder an den Abluftleitungen vorgenommen werden.
Vergewissern Sie sich vor der Installation, dass das Gerät keine
Transportschäden aufweist. Bei auftretenden Problemen setzen Sie sich
bitte mit Ihrem Händler in Verbindung.
Der Abstand zwischen der Abstellfläche auf dem Kochfeld und der Unterseite
der Dunstabzugshaube darf 50cm im Fall von elektrischen Kochfeldern und 65
cm im Fall von Gas- oder kombinierten Herden nicht unterschreiten.
Wenn die Installationsanweisungen des Gaskochgeräts einen größeren Abstand
vorgeben, ist dieser zu berücksichtigen.
ELEKTRISCHER ANSCHLUSS
Die Netzspannung muss der Spannung entsprechen, die auf dem
Betriebsdatenschild im Innern der Haube angegeben ist. Sofern die Haube einen
Netzstecker hat, ist dieser an zugänglicher Stelle an eine den geltenden
Vorschriften entsprechende Steckdose nach der Montage anzuschließen. Bei
einer Haube ohne Stecker (direkter Netzanschluss) oder falls der Stecker nicht
zugänglich ist, ist ein normgerechter zweipoliger Schalter nach der Montage
anzubringen, der unter Umständen der Überspannung Kategorie III
entsprechend den Installationsregeln ein vollständiges Trennen vom Netz
garantiert.
HINWEIS!
Vor der Inbetriebnahme muss sichergestellt werden, dass die
Netzversorgungleitung (Steckdose) ordnungsgemäß montiert wurde.
Austausch des Netzkabels
Die Dunstabzugshaube ist mit einem Spezialkabel ausgestattet. Sollte das Kabel
beschädigt werden, muss beim Kundendienst Ersatz angefordert werden.
19
ABLEITUNG DER ABLUFT
(bei Abluftversionen)
Die Dunstabzugshaube an Abluftrohre und Abluftöffnungen in der Wand
anschließen, die den gleichen Durchmesser haben wie der Abluftstutzen
(Anschlussflansch).
Die Benutzung von Rohren und Abluftöffnungen mit geringerem Durchmesser
verursacht eine Verringerung der Abluftleistung und eine drastische Zunahme
der Geräuschentwicklung.
Bei Nichtbeachtung der Anweisungen übernimmt der Hersteller keine Haftung.
! Ein möglichst kurzes Rohr verwenden.
! Ein Rohrsystem mit einer möglichst geringen Anzahl von Krümmungen
verwenden (max. Winkel der Krümmung: 90°).
! Starke Änderungen des Rohrdurchmessers sind zu vermeiden.
! Jegliche Verantwortung wird von der Firma abgelehnt, sollten diese Normen
nicht respektiert werden.
UMLUFT- ODER ABLUFTBETRIEB ?
! Ihre Haube wird als Abzugshaube geliefert.
Um die Abzugshaube in der Umluftversion verwenden zu können, braucht
der AKTIVKOHLE-FILTERSYSTEM installiert zu werden.
Stellen Sie in den ersten Seiten dieser Gebrauchsanleitung fest, ob das
AKTIVKOHLE-FILTERSYSTEM mitgeliefert oder separat erhältlich ist.
Anmerkung: Wenn das Aktivkohle-Filtersystem mitgeliefert wird, kann es
schon in der Haube installiert worden sein.
Die Informationen über den Umbau der Abzugshaube in Umlufthaube sind
in dieser Gebrauchsanleitung enthalten.
Abluftbetrieb
Die Luft wird mit Hilfe eines Rohrs ins Freie geleitet, das am Abluftstutzen
angebracht wird.
HINWEIS!
Das Abluftrohr wird nicht mitgeliefert und muss separat erworben werden.
Das Abluftrohr muss den gleichen Durchmesser wie der Abluftstutzen aufweisen.
HINWEIS!
Sollte die Dunstabzugshaube mit Aktivkohlefilter versehen sein, so muss dieser
entfernt werden.
Umluftbetrieb
Die angesaugte Luft wird zuvor entfettet und desodoriert werden, bevor sie
wieder in den Raum zugeführt wird.
Um die Abzugshaube in dieser Version zu verwenden, müssen Sie ein
zusätzliches Filtersystem, welches auf Aktivkohle basiert, installieren.
BEDIENELEMENTE
Die Dunstabzugshaube ist mit einer Bedienungsblende ausgestattet, die mit
einer Steuerung für die Ansaugstärke bzw. -geschwindigkeit, sowie einer
Steuerung zur Einstellung der Arbeitsplatzbeleuchtung versehen ist.
T1. ON-OFF Taste Gebläsemotor
T2. Wahltaste Regelgeschwindigkeitsstufe (Lüfterleistung)
Hinweis: Die Intensivstufe (Leistung) (LED L3 blinkt) dauert ungefähr 5
Minuten, danach schaltet sich automatisch die mittlere
Geschwindigkeitsstufe (Lüfterleistung) ein (LED L2 leuchtet)
T3. ON/OFF-Taste Beleuchtung
T4. Wahltaste "Leise" Geschwindigkeitsstufe (Lüfterleistung)
L1. LED Mittlere Geschwindigkeitsstufe (Lüfterleistung)
L2. LED Hohe Geschwindigkeitsstufe (Lüfterleistung)
L3 LED Intensivstufe (Lüfterleistung) - auf Zeit eingestellt (5 Min.).
L4 LED Filtersättigung:
blinkt: Der Aktivkohlefilter muss gewartet werden.
leuchtet: Die Fettfilter müssen gewartet werden.
L5 LED Niedrige Geschwindigkeitsstufe (Lüfterleistung) (leise)
L1+L2+L3 blinken nacheinander auf: Automatischer Betrieb bei hohen
Temperaturen (siehe entsprechenden Absatz)
Reset Filtersättigung
Nach der Wartung der Filter lange auf die Taste T1 drücken, bis die LEDL4
ausgeht.
Einschaltung LED Aktivkohlefiltersättigung
Die LED-Anzeige für die Aktivkohlesättigung ist in der Regel abgeschaltet.
Um sie zu aktivieren:
Bei abgeschalteter Dunstabzugshaube gleichzeitig lange auf die TastenT1
und T4 drücken: Zuerst blinktL1 dann L2, um anzuzeigen, dass die
Filtersättigungsanzeige eingeschaltet ist.
Abschaltung LED Aktivkohlefiltersättigung Den oben beschriebenen
Vorgang wiederholen, zuerst blinkenL1 und L2 und danach nur L1, um
anzuzeigen, dass die Filtersättigungsanzeige abgeschaltet ist.
Automatikbetrieb bei hohen Temperaturen
Die Dunstabzugshaube ist mit einem Temperaturmessfühler ausgerüstet. Wenn
eine zu hohe Temperatur gemessen wird, schaltet der Messfühler automatisch
die mittlere Geschwindigkeitsstufe (Lüfterleistung) ein. Die Dunstabzugshaube
schaltet sich erst ab, wenn die vom Messfühler gemessene Temperatur merklich
gesunken ist.
WARTUNG
Reinigung
Zur Reinigung AUSSCHLIESSLICH ein mit flüssigem Neutralreiniger getränktes
Tuch verwenden. KEINE WERKZEUGE ODER GERÄTE FÜR DIE REINIGUNG
VERWENDEN! Keine Produkte verwenden, die Scheuermittel enthalten.
KEINEN ALKOHOL VERWENDEN!
Perimetralabluftpaneel
Das Perimetralabluftpaneel so oft wie den Fettschutzfilter putzen , ein Tuch und
ein nicht so hoch konzentriertes Reinigungsmittel benutzen. Niemals
Schleifmittel benutzen.
Wartung der Fettfilter
Diese dienen dazu, die Fettpartikel, die beim Kochen frei werden, zu
binden.
Dieser muss einmal monatlich gewaschen werden (oder wenn das
Sättigungsanzeigesystem der Filter – sofern bei dem jeweiligen Modell
vorgesehen – dies anzeigt). Das kann mit einem milden Waschmittel von Hand,
oder in der Spülmaschine bei niedriger Temperatur und einem Kurzspülgang
erfolgen. Der Metallfettfilter kann bei der Reinigung in der Spülmaschine
verfärben, was seine Filtermerkmale jedoch in keiner Weise beeinträchtigt.
Zwecks Demontage der Fettfilter den Aushakgriff ziehen.
20
Wartung des Aktivkohlefilters
Dieser Filter bindet die unangenehmen Gerüche, die beim Kochen
entstehen.
Je nach der Benetzungsdauer des Herdes und der Häfigkeit der Reinigung des
Fettfilters tritt nach einer mehr oder weniger langen Benutzungsdauer die
Sättigung des Aktivkohlefilters auf. Auf jeden Fall muß der Filtereinsatz
mindestens alle 4 Monate (oder wenn das Sättigungsanzeigesystem der Filter –
sofern bei dem jeweiligen Modell vorgesehen – diese Notwendigkeit anzeigt)
ausgewechselt werden.
Er kann NICHT gereinigt oder erneut aktiviert werden.
Montage
Den Aktivkohlefilter zuerst von hinten auf der metallischen Feder der Saugkappe
anhängen, dann von vorne mit den zwei Knöpfen.
Demontage
Den Aktivkohlefilter entnehmen, in dem man die Knöpfe, die an der Saugkappe
fixiert sind, auf 90° dreht.
Ersetzen der Lampen
Die Haube ist mit einem auf der Leuchtdiodentechnologie basierten
Beleuchtungssystem ausgestattet.
Die LEDs ermöglichen eine optimale Beleuchtung der Kochfläche. Sie haben die
zehnfache Lebensdauer, verglichen mit herkömmlichen Lampen, und bieten eine
Energieersparnis bis zu 90%.
Um die LEDs mit neuen zu ersetzen, setzen Sie sich bitte mit dem Kundendienst
in Verbindung.
ENTSORGUNG
In Übereinstimmung mit den Anforderungen der Europäischen Richtlinie
2012/19/EC über Elektro- und Elektronik-Altgeräte (WEEE) ist vorliegendes
Gerät mit einer Kennzeichnung versehen.
Sie leisten einen positiven Beitrag für den Schutz der Umwelt und die
Gesundheit des Menschen, wenn Sie dieses Gerät einer gesonderten
Abfallsammlung zuführen. Im unsortierten Siedlungsmüll könnte ein solches
Gerät durch unsachgemäße Entsorgung negative Konsequenzen nach sich
ziehen.
Auf dem Produkt oder der beiliegenden Produktdokumentation ist folgendes
Symbol
einer durchgestrichenen Abfalltonne abgebildet. Es weist darauf
hin, dass eine Entsorgung im normalen Haushaltsabfall nicht zulässig ist.
Entsorgen Sie dieses Produkt im Recyclinghof mit einer getrennten Sammlung
für Elektro- und Elektronikgeräte. Die Entsorgung muss gemäß den örtlichen
Bestimmungen zur Abfallbeseitigung erfolgen.
Bitte wenden Sie sich an die zuständigen Behörden Ihrer Gemeindeverwaltung,
an den lokalen Recyclinghof für Haushaltsmüll oder an den Händler, bei dem Sie
dieses Gerät erworben haben, um weitere Informationen über Behandlung,
Verwertung und Wiederverwendung dieses Produkts zu erhalten.
Gerät entwickelt, getestet und hergestellt nach:
•Sicherheit: EN/IEC 60335-1; EN/IEC 60335-2-31, EN/IEC 62233.
•Leistungsfähigkeit/Gebrauchstauglichkeit: EN/IEC 61591; ISO 5167-1; ISO
5167-3; ISO 5168; EN/IEC 60704-1; EN/IEC 60704-2-13; EN/IEC 60704-3; ISO
3741; EN 50564; IEC 62301.
•EMC: EN 55014-1; CISPR 14-1; EN 55014-2; CISPR 14-2; EN/IEC 61000-3-2;
EN/IEC 61000-3-3. Empfehlungen für eine korrekte Verwendung, um die
Umweltbelastung zu verringern: Schalten Sie Haube beim Kochbeginn bei
kleinster Geschwindigkeit EIN und lassen Sie die Haube einige Minuten
nachlaufen, wenn Sie mit dem Kochen fertig sind. Erhöhen Sie die
Geschwindigkeit nur bei großen Mengen von Kochdunst und Dampf und
benutzen Sie die Intensivstufe(n) nur bei extremen Situationen. Wechseln Sie
die Kohlefilter, wenn notwendig, um eine gute Geruchsreduzierung zu
gewährleisten. Säubern Sie die Fettfilter, wenn notwendig, um eine gute
Fettfilterungseffizienz zu gewährleisten. Verwenden Sie den in der
Gebrauchsanweisung angegebenen grössten Durchmesser des
Luftaustrittssystems, um die Leistungsfähigkeit zu optimieren und die
Geräuschentwicklung zu minimieren.
BETRIEBSSTÖRUNGEN
Wenn etwas nicht zu funktionieren scheint, folgende Kontrollen durchführen,
bevor der Kundendienst gerufen wird:
Wenn die Abzugshaube nicht funktioniert:
Prüfen, ob:
- ein Stromausfall vorliegt.
- eine Geschwindigkeit gewählt wurde.
Wenn die Leistung der Abzugshaube mangelhaft ist:
Prüfen, ob:
- die gewählte Motorgeschwindigkeit für die freigesetzte Menge an Rauch
und Dämpfen ausreicht.
- die Küche ausreichend belüftet ist, um eine Luftansaugung zuzulassen.
- der Kohlefilter verbraucht ist (bei Umluftversion).
Wenn sich die Haube im Laufe des normalen Betriebs selbst ausgeschaltet
hat.
Prüfen, ob:
- ein Stromausfall vorliegt.
- die allpolige Trennvorrichtung ausgelöst wurde.
Die Dunstabzugshaube oder die Bedienungselemente funktionieren nicht: Für
mindestens 5 Sekunden die Stromversorgung der Dunstabzugshaube unter-
brechen und dann die Haube erneut einschalten. Kann die Störung nicht
behoben werden, kontaktieren Sie bitte den Kundendienst.
TECHNISCHE DATEN
Modell
Höhe
(cm)
Breite
(cm)
Tiefe
(cm)
Ø des
Abluftrohrs
(cm)
HIF 9.3F LB X
HIGC 9.3F LB X
60,9 – 113
72,2 –113
89,8 59,8 15-12,5-12
Siehe Typenschild für die gesamte Lichtabsorption und die Absorption der
Lampe.
Teile, die nicht zum Lieferumfang des Produkts gehören
1 / 1

Hotpoint UIF 9.3F LB X Guida utente

Categoria
Cappe da cucina
Tipo
Guida utente