Husqvarna Z454XS Zero Turn Lawn Mower Manuale utente

Z454X

EN Operator's manual 2-33

FR Manuel d'utilisation 34-68

NL Gebruiksaanwijzing 69-101

IT Manuale dell'operatore 102-136

ES Manual de usuario 137-170

DE Bedienungsanweisung 171-205

Contents

Conformity certificates.............................................. 2

Introduction............................................................... 2

Safety........................................................................7

Operation................................................................ 11

Maintenance........................................................... 15

Troubleshooting...................................................... 24

Transportation, storage and disposal......................27

Technical data.........................................................28

Service....................................................................30

EU declaration of conformity...................................32

UK Declaration of conformity ................................. 33

Conformity certificates

USA requirements

Labels are placed on the engine and/or in the engine

compartment stating that the machine will fulfill the

requirements. This is also applicable to special

requirements for any of the states, (California

emission rules etc.). Do not remove these labels.

Certificates can also be supplied with the machine at

delivery or written in the Engine manual. Take care

of them as they are valuable documents.

WARNING: Failure to follow

cautious operating practices can result in

dangerous injury to the operator or other

persons. The owner must understand

these instructions, and must let only

approved persons who understand these

instructions to operate the mower. Each

person operating the mower must be of

sound mind and body and must not be

under the influence of mind altering

substances.

WARNING: The rollover protection

structure can be impaired by damage if

the mower is overturned or if alteration to

the ROPS occurs. If these conditions

take place, the total structure MUST be

replaced.

WARNING: Engine exhaust, some

of its constituents, and certain vehicle

components contain or emit chemicals

known to the State of California to cause

cancer and birth defects or other

reproductive harm.

WARNING: Battery posts, terminals

and related accessories contain lead and

lead compounds, chemicals known to

the State of California to cause cancer

and birth defects or other reproductive

harm. Clean your hands after handling.

WARNING: Engine exhaust and

certain vehicle components contain or

emit chemicals considered to cause

cancer, birth defects, or other

reproductive system damage. The

engine exhaust contains carbon

monoxide, which is an odorless,

colorless, poisonous gas. Do not use the

machine in enclosed spaces.

When this product is worn out and no longer used,

return it to the reseller or other party for recycling.

To implement improvements, specifications and

designs can be altered without prior notification.

Use only original parts for repairs. The use of other

parts voids the warranty.

Do not modify or install non-standard equipment to

the unit without consent from the manufacturer.

Modifications to the unit may cause unsafe

operations or damage the unit.

Introduction

Pre-delivery inspection and product

numbers

A pre-delivery inspection has been done of this

product. Make sure that you receive a signed copy of

the pre-delivery inspection document from your

dealer.

Service agent contact information:

This operator’s manual is for product with product number / serial number:

21741 - 001 - 08.11.2021

/

Engine:

Transmission:

The product numbers are found on the type plate.

Refer to

Product overview on page 3

for the

location of the type plate.

Product description

This product is a ride-on lawn mower. The control

levers let the operator steer the product and adjust

the speed of the product. An hour meter shows how

many hours the product has been used.

Intended use

The product is made to cut grass on open and level

ground only. Do not use the product for other tasks.

Product overview

5

4

3

16

14

15

13

3

12

11

10

9

8

7

11 12

16

17

1. Control levers

2. Parking brake

3. Tracking control

4. Hour meter

5. Fuel shut-off valve

6. Hydraulic release lever

1741 - 001 - 08.11.2021 3

7. Fuses

8. Fuel tank cap

9. Choke control

10. Ignition switch

11. Throttle control

12. PTO button

13. Fuel gauge

14. Seat adjustment lever

15. Deck lifting lever

16. Type plate

17. ROPS

Roll Over Protection Structure

(ROPS)

ROPS is a protective frame that decreases the risk

of injury if the product overturns. Use the ROPS and

the safety belt when you operate the product on

slopes.

Steering controls

The direction of the product is controlled by the 2

control levers. Refer to

Product overview on page 3

.

The control levers can be moved forward and

rearward from a neutral position. Refer to

To operate

the product on page 13

.

Operator Presence Control (OPC)

The OPC engages when the operator lifts from the

seat. The engine and the drive to the blades stop if

the blades are engaged or the parking brake is not

applied. Refer to

Operation conditions on page 9

.

Ignition key

The ignition key has 4 positions:

• Start position (A)

• Run position (B)

• Headlight position (C)

• Stop position (D)

A

B

C

D

Headlights

A

B

C

D

• Turn the ignition key to the headlight position (C)

to operate the product with the headlights on.

• Turn the ignition key to the run position (B) to

operate the product with the headlights off.

Throttle control

The throttle control adjusts the speed of the engine

and the speed of the blades if the blades are

engaged. The throttle control has 2 end positions,

idle speed and full throttle.

AA B

• Idle speed (A) - decreases the engine speed.

• Full throttle (B) - increases the engine speed.

CAUTION: Do not operate the

engine at idle speed (A) for longer time

than necessary. Too much operation

time at idle speed can decrease the life

of the spark plugs.

Choke control

The choke control is used for cold starts to supply

more fuel to the engine. Pull up the choke control

when you start a cold engine.

Refer to

Product overview on page 3

for the position

of the choke control.

PTO (Power Take-Off) button

The PTO button engages and disengages the PTO

clutch and the cutting deck or other equipment

connected to it. The correct start conditions must be

obeyed to engage the drive of the blades. Refer to

Operation conditions on page 9

for the correct

start conditions.

41741 - 001 - 08.11.2021

• Pull the PTO button out to engage the drive to

the blades or other equipment.

• Push the PTO button in to disengage the drive to

the blades or other equipment.

Fuel gauge

The fuel gauge shows the fuel level and will flash

yellow when the fuel level is approximately 1.0

gallons/3.8 l. Refer to

Product overview on page 3

for the position of the fuel gauge.

Fuel shut-off valve

Refer to

Product overview on page 3

for the position

of the fuel shut-off valve.

The fuel shut-off valve is closed when the tab on the

knob is perpendicular to the fuel line.

Fuses

The location of the fuses is in the fuse box. The fuse

box is below the seat. Tilt the seat forward to get

access the fuse box. Refer to the decal on the fuse

box for identification of the different fuses.

Hour meter

The product has an hour meter that show how many

hours of operation that the blades have been

engaged. Refer to

Product overview on page 3

for

the position of the hour meter.

Each 50 hours an oil level symbol will show for 2

hours. Refer to

Lubrication schedule on page 23

.

Symbols on the product

WARNING: This product can be

dangerous and cause serious injury or

death to the operator or others. Be

careful and use the product correctly.

Use protective glasses.

Parking brake.

Engine speed – fast.

Slow.

Fuel.

Use protective gloves.

Stop the engine before maintenance.

Do not operate the product without

deflector or grass catcher.

1741 - 001 - 08.11.2021 5

Always use approved hearing

protection.

Do not put your foot here.

Neutral gear.

Reverse gear.

Read the operator's manual carefully

and make sure that you understand the

instructions before you use the product.

Keep a safe distance from the product.

Do not operate the product on slopes

larger than 10°.

Do not keep passengers.

Look out for ejecting objects and

ricochets.

Keep hands and feet clear.

Keep hands away from rotating parts.

Look out for persons and animals when

you operate the product forward.

Look out for persons and animals when

you operate the product rearward.

Choke.

Sound power level.

The product agrees with the applicable

EC directives.

This product conforms to the applicable

UK regulations.

Keep away from the dis-

charge deck.

Warning! Battery acid is

corrosive, explosive and

flammable.

Keep body parts away

from rotating parts.

yyyywwxxxx The rating plate shows

serial number. yyyy is

the production year and

ww is the production

week.

Note: Other symbols/decals on the product refer

to certification requirements for some commercial

areas.

Product liability

As referred to in the product liability laws, we are not

liable for damages that our product causes if:

• the product is incorrectly repaired.

• the product is repaired with parts that are not

from the manufacturer or not approved by the

manufacturer.

• the product has an accessory that is not from the

manufacturer or not approved by the

manufacturer.

• the product is not repaired at an approved

service center or by an approved authority.

Euro V Emissions

WARNING: Tampering with the

engine voids the EU type-approval of

this product.

61741 - 001 - 08.11.2021

Safety

Safety definitions

Warnings, cautions and notes are used to point out

specially important parts of the manual.

WARNING: Used if there is a risk of

injury or death for the operator or

bystanders if the instructions in the

manual are not obeyed.

CAUTION: Used if there is a risk of

damage to the product, other materials

or the adjacent area if the instructions in

the manual are not obeyed.

Note: Used to give more information that is

necessary in a given situation.

General safety instructions

WARNING: Read the warning

instructions that follow before you use

the product

WARNING: This product is capable

of amputating hands and feet and

throwing objects. Failure to observe the

following safety instructions could result

in serious injury or death.

• Read, understand, and follow instructions and

warnings in this document, the operator’s manual

and on the product, engine and attachments.

• Only allow operators, who are responsible,

trained, familiar with the instructions, and

physically capable to operate the product.

• Do not carry passengers and keep bystanders

away.

• Do not operate the product while under the

influence of alcohol or drugs.

• Follow the manufacturer’s recommendation for

wheel weights or counterweights.

• Learn how to use the product and its controls

safely and learn how to stop the product quickly.

• Learn to recognize the safety decals.

• Keep the product clean to make sure that you

can clearly read signs and stickers.

• Keep in mind that the operator will be held

responsible for accidents that involve other

persons or their property.

• Only use the product in daylight or in other well-lit

conditions. Keep the product at a safe distance

from holes or other irregularities in the ground.

Look out for other possible risks.

• Do not let children or other persons not approved

for operation of the product to use or do servicing

on it. Local laws may regulate the age of the

user.

• Make sure that nobody else is in the vicinity of

the product when you start the engine, engage

the drive or start to move the product.

• Keep an eye on the traffic when you mow near a

road or move across a road.

• Do not use the product if you are fatigued, while

under the influence of alcohol or drugs, medicine

or anything that can have a negative effect on

your vision, alertness, coordination or judgement.

• Always park the product on a level surface with

the engine stopped.

Safety instructions regarding children

WARNING: Read the warning

instructions that follow before you use

the product.

• Tragic accidents can occur if the operator is not

alert to the presence of children. Children are

often attracted to the product and the mowing

activity. Never assume that children will remain

where you last saw them.

• Keep children out of the operating area and

under the watchful care of a responsible adult

other than the operator.

• Do not carry children, even with the blade(s) shut

off. Children could fall off and be seriously injured

or interfere with safe product operation. Children

who have been given rides in the past could

suddenly appear in the mowing area for another

ride and be run over or backed over by the

product.

Safety instructions for operation

WARNING: Read the warning

instructions that follow before you use

the product.

WARNING: Do not touch the

engine or exhaust system during or

directly after operation. The engine and

the exhaust system become very hot

during operation. Risk of burn injuries,

fire and damage to property or adjacent

areas. When you operate the product,

keep away from bushes and other

objects.

• Only operate the engine in well ventilated areas.

Exhaust gases contain carbon monoxide, a

deadly poison.

1741 - 001 - 08.11.2021 7

• Only operate the product in daylight or good

artificial light.

• Avoid holes, ruts, bumps, rocks, or other hidden

hazards. Uneven terrain could overturn the

product, or cause operator to lose their balance

or footing.

• Do not put hands or feet near rotating parts or

under the product. Keep clear of the discharge

opening at all times.

• Do not direct discharge material toward anyone.

Avoid discharging material against a wall or

obstruction. Material may ricochet back toward

the operator. Stop the blade(s) when crossing

gravel surfaces.

• Do not leave a running product unattended.

Always park on level ground, disengage the

attachment, set parking brake, and stop engine/

motor.

• Do not mow in reverse unless absolutely

necessary. Always look down and behind before

and while backing.

• Decrease the speed before you turn around a

corner.

Safety instructions for operation on slopes

WARNING: Read the warning

instructions that follow before you use

the product.

Slopes are a major factor related to accidents.

Operation on slopes requires extra caution.

• Travel in the manufacturer recommended

direction on slopes. Use caution while operating

near dropoffs.

• Avoid mowing wet grass. (Poor footing could

cause a slip and fall accident.)

• Do not operate product under any condition

where traction, steering, or stability is in question.

Tires could slide even if the wheels are stopped.

• Always keep the product in gear when going

down slopes. Do not coast downhill.

• Avoid starting and stopping on slopes. Avoid

making sudden changes in speed or direction.

Make turns slowly and gradually.

• Use extra care while operating product with a

grass catcher or other attachment(s). They can

affect the stability of the product.

• To cut grass on slopes increases the risk that

you can not control the product and that it

overturns. This can cause injury or death. It is

necessary to cut the grass carefully on all slopes.

If you cannot reverse up a slope or if you do not

feel safe, do not cut it.

• Remove stones, branches and other obstacles.

• Cut the grass on the slope up and down, not

from side to side.

• Do not operate the product on ground that slopes

more than 10°.

• Move smoothly and slowly on slopes.

• Look out for and do not move across furrows,

holes and bumps. There is a higher risk that the

product overturns on ground that is not flat. Long

grass can hide obstacles.

• Do not cut grass near edges, ditches or banks.

The product can suddenly overturn if a wheel

moves across the edge of a steep slope or a

ditch, or if an edge gives way.

Safety instructions for operation on slopes

• The ROPS is an integral and effective safety

device. Do not remove or alter the ROPS.

• Keep a folding ROPS in the raised and locked

position and use the seat belt when operating the

product.

• Lower a folding ROPS temporarily only when

absolutely necessary. Do not wear the seat belt

when folded down. There is no rollover protection

when a folding ROPS is in the down position.

• Replace a damaged ROPS. Do not repair or

alter.

Personal protective equipment

WARNING: Read the warning

instructions that follow before you use

the product.

• Use approved personal protective equipment

when you use the product. Personal protective

equipment cannot fully prevent injury but it

decreases the degree of injury if an accident

does occur. Let your dealer help you select the

right equipment.

• Always wear approved hearing protection. Long

term exposure to noise can result in permanent

hearing impairment.

• Always wear protective shoes or protective

boots. Steel toes are recommended. Do not use

the product barefoot.

• Wear gloves when necessary, for example when

you attach, examine or clean the cutting

equipment.

• Do not wear loose-fitting clothing, jewelry or

other items that can get caught in moving parts.

• Keep first aid equipment and fire extinguisher

close at hand.

81741 - 001 - 08.11.2021

Safety devices on the product

WARNING: Read the warning

instructions that follow before you use

the product.

• Do not use a product with defective safety

devices. Do a check of the safety devices

regularly. If the safety devices are defective,

speak to your Husqvarna service agent.

• Do not make modifications on safety devices. Do

not use the product if protective plates, protective

covers, safety switches or other protective

devices are not attached or are defective.

To engage and disengage the Roll Over Protection

Structure (ROPS)

• Remove the 2 pins that hold the ROPS and fold it

rearwards to disengage. Engage the ROPS in

the opposite sequence.

WARNING: Obey the following

instructions for the ROPS and the

safety belt.

• Do not use the safety belt if the ROPS is

disengaged.

• Always use the safety belt when the ROPS is

engaged.

• Make sure that the ROPS is correctly attached

and not damaged.

To do a check of the ignition lock

• Start and stop the engine to do a check of the

ignition lock. Refer to

To start the engine on page

13

and

To stop the engine on page 14

.

• Make sure that the engine starts when you turn

the ignition key to start position.

• Make sure that the engine stops immediately

when you turn the ignition key to stop position.

Operation conditions

These conditions are necessary to start the engine:

• The control levers are in the neutral position.

• The parking brake is applied.

• The drive of the blades is disengaged.

• The OPC is pushed down.

The engine must stop in these situations:

• The parking brake is not applied and the operator

lifts from the seat.

• The drive of the blades is engaged and the

operator lifts from the seat.

Try to start the engine without 1 of the conditions.

Change the conditions and try again. Do this check

daily.

Parking brake

WARNING: If the parking brake

does not work, the product can start to

move and cause injury or damage. Make

sure that the parking brake is regularly

examined and adjusted.

Refer to

To do a check of the parking brake on page

18

.

Muffler

WARNING: Do not use the product

if the muffler is missing or defective. A

defective muffler increases the noise

level and the risk of fire.

The muffler keeps the noise levels to a minimum and

sends the exhaust fumes away from the operator.

Examine the muffler regularly to make sure that it is

attached correctly and not damaged.

WARNING: The muffler becomes

very hot during and after use and when

the engine operates at idle speed. Be

careful near flammable materials and/or

fumes to prevent fire.

To do a check of the muffler

• Examine the muffler regularly to make sure that it

is attached correctly and not damaged.

Spark arrestor

This product has an internal-combustion engine. Do

not use the product near vegetation without a spark

arrestor that is approved by local or state laws.

Federal laws apply on federal lands.

A spark arrestor for the muffler is available through

your approved Husqvarna dealer.

Protective covers

Missing or damaged protective covers increase the

risk of injury on moving parts and hot surfaces. Do a

check of the protective covers before you operate

the product. Make sure that the protective covers are

correctly attached and do not have cracks or other

damages. Replace damaged covers.

1741 - 001 - 08.11.2021 9

Fuel safety

WARNING: Read the warning

instructions that follow before you use

the product.

WARNING: Be careful with fuel. It

is very flammable, and can cause injury

and damage to property.

• Extinguish all cigarettes, cigars, pipes and other

sources of ignition.

• Use only an approved fuel container.

• Do not remove fuel cap or add fuel with the

engine running or while hot.

• Do not refuel indoors or in enclosed spaces.

• Do not store the product or fuel container, or

refuel, where there is an open flame, spark, or

pilot light such as on a water heater or other

appliance.

• If fuel is spilled, do not attempt to start the engine

and avoid creating any source of ignition until

fuel vapors have dissipated.

• To help prevent fires: keep product free of grass,

leaves, or other debris build up; clean up oil or

fuel spillage and remove any fuel soaked debris;

allow product to cool before storing.

• Use extra care in handling gasoline and other

fuels. They are flammable and vapors are

explosive.

• Gasoline and gasoline fumes are poisonous and

very flammable. Be careful with gasoline to

prevent injury or fire.

• Let the engine become cool before you refuel.

• Do not fill fuel near sparks or naked flames.

• If there are leaks in the fuel system, do not start

the engine until the leaks are repaired.

• Do not fill above recommended fuel level. The

heat from the engine and the sun makes the fuel

expand and the fuel overflows if the tank is filled

too much.

• Store the product and fuel in such a way that

there is no risk that fuel leaks or fumes can

cause damage.

Transport safety

• Use an approved transport vehicle for

transportation of the product.

• A markets national or local regulations can set

limit to the transportation of the product.

• The operator of the transport vehicle is

responsible to attach the product safely during

transport. Refer to

Transportation on page 27

.

Hauling

• Use full width ramps for loading and unloading a

product for transport.

Towing safety

• Follow the manufacturer’s recommendation for

weight limits for towed equipment and towing on

slopes.

• Only use tow equipment approved by

Husqvarna.

• Use the tow bar to attach the equipment.

• Make sure that no other persons are near the

product when you tow equipment.

• Do not let children or others in or on the towed

equipment.

• Do not tow on slopes or rough ground. The

weight of the towed equipment can cause loss of

traction and loss of control.

Battery safety

WARNING: A damaged battery can

cause an explosion and cause injury. If

the battery has a deformation or is

damaged, speak to an approved

Husqvarna service agent.

WARNING: Read the warning

instructions that follow before you use

the product.

• Use protective glasses when you are near

batteries.

• Do not wear watches, jewelry or other metal

objects near the battery.

• Keep the battery out of reach for children.

• Charge the battery in a space with good airflow.

• Keep flammable materials at a minimum

clearance of 1 m when you charge the battery.

• Discard replaced batteries. See

Disposal on

page 27

.

• Explosive gases can come from the battery. Do

not smoke near the battery. Keep the battery

away from open flames and sparks.

Safety instructions for maintenance

WARNING: Read the warning

instructions that follow before you use

the product.

WARNING: The product is heavy

and can cause injury or damage to

property or the adjacent area. Do not do

maintenance on the engine or the cutting

deck without these conditions:

• The engine is off.

• The product is parked on a level

surface.

• The parking brake is applied.

• The ignition key in stop position and

removed.

10 1741 - 001 - 08.11.2021

• The blades are disengaged.

• All moving parts have stopped.

• The ignition cables are removed from

the spark plugs.

WARNING: Fluid escaping under

pressure may have sufficient force to

penetrate skin and cause serious injury.

If fluid is injected into the skin, seek

immediate medical attention. Keep body

and hands away from pin holes or

nozzles that eject fluid under high

pressure. If a leak occurs, have the

product immediately serviced by a

trained technician.

WARNING: The exhaust fumes

from the engine contain carbon

monoxide, an odorless, poisonous and

very dangerous gas. Do not run the

product in closed spaces or spaces with

no sufficient air flow.

• Keep the product in good working order. Replace

worn or damaged parts.

Use caution when servicing blades. Wrap the

blade(s) or wear gloves. Replace damaged

blades. Do not repair or alter blade(s).

If equipped, disconnect spark plug wire(s) and

the negative battery cable before making any

repairs.

For best performance and safety, do

maintenance on the product regularly as given in

the maintenance schedule. Refer to

Maintenance

schedule on page 15

.

• Electrical shocks can cause injuries. Do not

touch the cables when the engine is on. Do not

do a function test on the ignition system with your

fingers.

• Let the product become cool before you do

maintenance near the engine.

• The blades are sharp and can cause cuts. Wind

protection around the blades or use protective

gloves when you do work on the blades.

• Do not turn the engine over if the spark plug or

ignition cable is removed.

• Make sure that all nuts and bolts are tightened

correctly and that the equipment is in good

condition.

• Do not change the adjustment of governors. If

the engine speed is too high, the product

components can become damaged. Refer to

Technical data on page 28

for highest permitted

engine speed.

• The product is approved only with the equipment

supplied or recommended by the manufacturer.

Operation

Introduction

WARNING: Before you operate the

product, you must read and understand

the safety chapter.

To operate the product for the first

time

WARNING: Before you operate the

product for the first time, you must read

and understand the this chapter.

• Use a decreased throttle speed and a decreased

ground speed when you operate the product for

the first time.

• Do not move the control levers to the fully

forward position or the fully reverse position

during the initial operation.

• Learn how to operate the movement of the

product on a hard surface, for example concrete

or asphalt, before you operate the product on a

lawn for the first time.

To do before you operate the

product

WARNING: Before you operate the

product, you must read and understand

the safety chapter.

WARNING: Before you operate the

product, you must make sure that there

are no stones or other objects in the

work area that can be thrown by the

rotating blades.

• Do the daily maintenance. Refer to

Maintenance

schedule on page 15

.

• Make sure that there is sufficient fuel in the fuel

tank.

• Set the cutting height. Refer to

Maintenance

schedule for the operator on page 15

.

To fill fuel

WARNING: Gasoline is very

flammable. Be careful and refuel

outdoors, refer to

Fuel safety on page

10

.

1741 - 001 - 08.11.2021 11

WARNING: The engine and the

exhaust system become very hot during

operation. Risk of burn injury. Let the

engine and the exhaust system become

cool before you fill fuel in the product.

WARNING: Do not use the fuel

tank as a support area.

CAUTION: Incorrect type of fuel can

result in engine damage.

The engine runs on gasoline with a minimum octane

rating of 91 RON (87 AKI), not mixed with oil. We

recommend biodegradable alkylate gasoline.

• Do a check of the fuel level before each use and

refuel if it is necessary.

• Do not fill the fuel tank fully. Fill to the bottom of

the fuel tank neck.

To adjust the seat

The position of the seat can be moved forward or

rearward and suspension of the seat can be

adjusted.

WARNING: Do not make

adjustments to the seat when the

product is in operation.

• Turn the knob below the seat (A) to adjust the

seat suspension. Turn the knob counterclockwise

for soft suspension and clockwise for hard

suspension.

B

A

• Push the lever below the seat (B) to the side and

push the seat forward or rearward.

To fold the seat

The seat can be folded forward to get access to the

battery and hydrostatic transmission system.

1. Park the product on level ground.

2. Push the lever and push the backrest of the seat

forward to fold the seat forward.

To engage and disengage the

parking brake

This product has no dedicated parking brake lever.

The parking brake is integrated in the 2 control

levers.

• Push the 2 control levers away from the seat at

the same time to engage the parking brake.

Refer to

Product overview on page 3

for the

location of the control levers.

Note: The product must be stationary when

you engage the parking brake.

Note: The engine will stop if you do not push

the 2 control levers away from the seat at the

same time.

• Pull the 2 control levers in the direction of the

seat to disengage the parking brake.

To disengage and engage the drive

system

CAUTION: Only disengage or

engage the drive system when the

product is parked on level ground.

If it is necessary to move the product by hand, with

the engine off, the drive system must be disengaged.

The drive system is disengaged and engaged by the

bypass valves. The bypass valves are found on the

front of each transmission.

Follow the procedure below to disengage the drive

system.

1. Park the product on level ground and stop the

engine.

2. Set the cutting deck to the lowest position.

3. Set the control levers in neutral position.

4. Lift the seat.

12 1741 - 001 - 08.11.2021

5. Turn the 2 bypass levers to the horizontal

position.

Note: Push the product by hand onto a truck

or trailer. Do not push the control levers.

6. To engage the drive system, turn the bypass

levers to the vertical position.

To set the cutting deck in transport

position or mow position

The cutting deck must be in transport position during

transportation.

• Push the deck lift pedal until the cutting deck

latches in the transport position.

• Push the deck release pedal and pull the

transport release lever to lower the cutting deck

into mow position.

To set the cutting height

1. Set the cutting deck in transport position. Refer

to

To set the cutting deck in transport position or

mow position on page 13

.

2. Put the pin (A) in the hole for the correct cutting

height.

A

B

C

3. Push the deck lift pedal (B) and pull the transport

release lever (C) rearward to lower the cutting

deck into mow position.

To start the engine

1. Sit on the seat.

2. Push the PTO button to disengage the drive on

the cutting deck.

3. Set the cutting deck in transport position. Refer

to

To set the cutting deck in transport position or

mow position on page 13

.

4. Engage the parking brake. Refer to

To engage

and disengage the parking brake on page 12

.

5. Move the throttle lever (A) to ½ throttle position.

A

BC

6. If the engine is cold, pull the choke control (B)

up.

7. Open the fuel tank valve.

8. Press and turn the ignition key (C) to the start

position.

9. When the engine starts, immediately release the

ignition key to the run position.

Note: Do not keep the ignition key in the start

position for more than 5 seconds at a time. If the

engine does not start, wait 15 seconds before

you try again.

10. If the engine is cold, slowly push the choke

control down.

11. Let the engine run at ½ throttle for 3-5 minutes

before you apply full throttle.

12. Push the throttle control to the full throttle

position.

To operate the product

1. Start the engine. Refer to

To start the engine on

page 13

.

2. Disengage the parking brake. Refer to

To

engage and disengage the parking brake on

page 12

.

1741 - 001 - 08.11.2021 13

3. Carefully push the 2 control levers forward. The

product will start to move forward. The forward

speed increases the more the 2 control levers

are pushed forward.

4. Carefully pull the 2 control levers rearward. The

product will start to move rearward. The rearward

speed increases the more the 2 control levers

are pulled rearward.

5. Put the 2 control levers in neutral position to

decrease the speed and stop the product.

6. Do the steps that follow to turn left or right when

you go in a forward direction.

a) Pull the left control lever rearward in the

direction of the neutral position to make the

product turn left. The more you pull the left

control lever rearward, the more the product

will turn left.

b) Pull the right control lever rearward in the

direction of the neutral position to make the

product turn right. The more you pull the right

control lever rearward, the more the product

will turn right.

7. Do the steps that follow to make a zero turn.

a) Pull the 2 control levers rearward in the

direction of the neutral position to decrease

the speed or stop the product.

b) Move 1 control lever slightly forward and the

other control lever slightly rearward to make a

zero turn.

8. Lower the cutting deck to mow position. Refer to

To set the cutting deck in transport position or

mow position on page 13

.

9. Pull up the PTO button to engage the drive of the

blades.

10. If it is necessary to adjust the cutting height

during operation, refer to

To set the cutting

height on page 13

.

To stop the engine

1. Move the 2 control levers to the neutral position

to stop the product.

2. Engage the parking brake.

3. Push down the PTO button to disengage the

drive of the blades.

4. Put the cutting deck in the transport position.

5. Move the throttle control to the minimum throttle

position.

6. Let the engine idle for a minimum of 1 minute

until the engine is at usual operation

temperature.

7. Turn the ignition key to the stop position.

8. Remove the ignition key from the ignition when

you are away from the product.

To get a good cutting result

• For best performance, do maintenance on the

product regularly as given in the maintenance

schedule. Refer to

Maintenance schedule on

page 15

.

• Do not cut a wet lawn. Wet grass can give a bad

cutting result.

• Start with a high cutting height and decrease it

gradually.

• Use full throttle when you cut the grass.

• Move the product forward at low speed if the

grass is high and thick.

• Cut the grass in an irregular pattern.

• When the mulch kit is used, cut the grass more

frequently.

• To get the best cutting result, cut the grass

frequently.

14 1741 - 001 - 08.11.2021

To do a 3-point turn

A correct turn will prevent damage to the lawn. The

goal is to turn when you move forward or rearward.

Do not turn in a tight circle on a stopped wheel.

1. Cut a row of grass.

2. Make a small turn (A) in the direction of the uncut

area of grass.

A

B

C

3. Pull the 2 control levers to the reverse position

and move the product rearward (B).

4. Push the control levers forward. To make a small

turn (C), pull harder on the control lever that is in

the direction of the row you have cut before.

5. Push the 2 control levers forward to cut the next

row.

Maintenance

Introduction

WARNING: Before you do any

maintenance work you must read and

understand the safety chapter.

Maintenance schedule

* = The instructions are not given in this operator's

manual.

X = The instructions are given in this operator's

manual.

O = Refer to the engine manual for instructions.

Maintenance schedule for the operator

Maintenance

Daily maintenance Do mainte-

nance at a

minimum of

1 time each

year

Maintenance interval in hours

Before After 25 50 100 300

Do a check of the parking

brake. X * *

Do a check of the level of

the engine oil. O

Do a check of the safety

system. X

Make sure that there are

no fuel or oil leaks from

the product.

*

1741 - 001 - 08.11.2021 15

Maintenance

Daily maintenance Do mainte-

nance at a

minimum of

1 time each

year

Maintenance interval in hours

Before After 25 50 100 300

Make sure that there are

no damage on the prod-

uct.

*

Make sure that there are

no loose parts. *

Do a check for damages

on the cutting deck. *

Do a check of the cutting

deck for adjustment. X X

Do a check of the tire

pressures. X X X X

Do a check of the battery

connections. X X X X X

Do a check of the throttle

cable. O

Do a check of the caster

wheels (each 200 hours). X X

Do a check of the clear-

ance of the engine

valve.1

* *

Clean the air intake of the

engine. O O

Clean the air intake of the

engine.2O O

Clean the bottom side of

the cutting deck. X

Clean around the engine. *

Clean around the belts

and the belt pulleys. * * * *

Do a check of the belts

and the belt pulleys. X X

Clean the foam pre-filter

(if equipped).3O O

Replace the foam pre-fil-

ter (if equipped).4O

Clean the paper filter car-

tridge.5O O

1Must be done by approved service agent.

2In conditions with dust, cleaning and replacement must be done more frequently.

3In conditions with dust, cleaning and replacement must be done more frequently.

4In conditions with dust, cleaning and replacement must be done more frequently.

5In conditions with dust, cleaning and replacement must be done more frequently.

16 1741 - 001 - 08.11.2021

Maintenance

Daily maintenance Do mainte-

nance at a

minimum of

1 time each

year

Maintenance interval in hours

Before After 25 50 100 300

Examine the muffler and

spark arrestor screen. * * * *

Start the engine and

blades and listen for un-

usual sounds.

*

Sharpen the blades.6X X

Replace the blades. X X

Replace the spark plugs. O O

Replace the engine oil.7O O

Replace the engine oil fil-

ter. O O

Replace the fuel filter. O O

Replace the paper air fil-

ter.8O O

Do the 300-hour servic-

ing.9* *

To clean the product

CAUTION: Do not use a high-

pressure washer or a steam cleaner.

Water can go into bearings and electrical

connections and cause corrosion which

causes damage to the product.

Clean the product immediately after use.

• Do not clean hot surfaces such as the engine,

muffler and exhaust system. Wait until the

surfaces are cool, then remove the grass or dirt.

• Before you clean with water, clean with a brush.

Remove grass and dirt on and around the

transmission, the transmission air intake, and the

engine.

• Use running water from a hose to clean the

product. Do not use high-pressure.

• Do not point the water at electrical components

or bearings. Detergent usually increases the

damage.

• Use compressed air to clean the top side of the

mower deck.

• Use a water hose to clean below the cutting

deck.

• When the product is clean, start the cutting deck

for a short period to remove remaining water.

To clean the engine and the muffler

Keep the engine and muffler free from grass cuttings

and dirt. Grass cuttings soaked in fuel or oil on the

engine can increase the fire risk and the risk that the

engine becomes too hot. Let the engine cool before

it is cleaned. Clean with water and a brush.

Grass cuttings around the muffler dry quickly and are

a fire risk. Use a brush or remove the grass cuttings

with water when the muffler is cold.

To clean the battery

Corrosion and dirt on the battery and the terminals

can cause the power of the battery to decrease.

1. Remove the battery. Refer to

To remove and

install the battery on page 18

.

2. Flush the battery with water and let dry.

CAUTION: Do not use a high-

pressure washer or a steam cleaner.

Water can go into bearings and

electrical connections and cause

6Must be done by approved service agent.

7Replace the engine oil after the first 8-10 hours of operation. During heavy load or high ambient tem-

peratures, replace the engine oil each 50 hours.

8In conditions with dust, cleaning and replacement must be done more frequently.

9Must be done by approved service agent.

1741 - 001 - 08.11.2021 17

corrosion which causes damage to

the product.

3. Clean the terminals and the cable ends of the

battery cables with a wire brush.

To do a check of the parking brake

1. Park the product on a slope with a hard surface.

Note: Do not park the product on a grass

slope when you do a check of the parking brake.

2. Engage the parking brake.

3. If the product starts to move with the parking

brake engaged, let an approved service agent

adjust the parking brake.

4. Disengage the parking brake.

To charge the battery

• Charge the battery if it is too weak to start the

engine. Refer to

Battery charging times on page

30

for battery charging times.

• Use a standard battery charger.

CAUTION: Do not use a boost

charger or start booster. A boost

charger or a start booster will cause

damage to the electrical system of

the product.

• Always disconnect the battery charger before

you start the engine.

To do an emergency start of the

engine

If the battery is too weak to start the engine, you can

use jumper cables to do an emergency start. This

product has a 12 V system with negative ground.

The product that is used for the emergency start

must also have a 12 V system with negative ground.

To connect the jumper cables

WARNING: Risk of explosion

because of explosive gas that comes

from the battery. Do not connect the

negative terminal of the fully charged

battery to or near the negative terminal

of the weak battery.

CAUTION: Do not use the battery of

the product to start other vehicles.

1. Connect one end of the red cable to the

POSITIVE battery terminal (+) on the weak

battery (A).

B

A

C

D

2. Connect the other end of the red cable to the

POSITIVE battery terminal (+) on the fully

charged battery (B).

WARNING: Do not short circuit

the ends of the red cable against the

chassis.

3. Connect one end of the black cable to the

NEGATIVE battery terminal (-) on the fully

charged battery (C).

4. Connect the other end of the black cable to a

CHASSIS GROUND (D), away from the fuel tank

and the battery.

To remove the jumper cables

Note: Remove the jumper cables in the opposite

sequence to how you connect them.

1. Remove the BLACK cable from the chassis.

2. Remove the BLACK cable from the fully charged

battery.

3. Remove the RED cable from the 2 batteries.

To remove and install the battery

1. Fold the seat forward. Refer to

To fold the seat

on page 12

.

18 1741 - 001 - 08.11.2021

2. Remove the bolt and the nut from the battery

bracket and remove the battery bracket from the

battery.

3. Use 2 wrenches to disconnect the black battery

cable from the negative (–) terminal on the

battery.

4. Use 2 wrenches to disconnect the red battery

cable from the positive (+) terminal on the

battery.

5. Carefully remove the battery from the product.

6. Install in the opposite sequence.

To adjust the tracking speed

If the product does not move straight forward, the

tracking speed must be adjusted.

WARNING: Always adjust the

tracking speed in an open area without

bystanders.

1. Do a check of the tire pressure. Refer to

Tire

pressure on page 19

.

2. Turn the tracking controls fully in. Refer to

Product overview on page 3

for the location of

the tracking controls.

3. Turn the tracking controls out 4 turns.

CAUTION: More than 4 turns

can cause damage to the product.

4. Start the product.

5. Move the control levers forward fully and operate

the product at full throttle.

6. Turn the tracking control on the right side

gradually until the product starts to move right.

7. Turn the tracking control on the left side

gradually until the product starts to move straight

forward.

Tire pressure

Make sure to have the correct tire pressure on all 4

tires. Refer to

Technical data on page 28

.

To remove and install the front

wheels

1. Remove the nut and the bolt to remove the front

wheels from the forks.

2. Install in the opposite sequence. Torque the nut

and bolt to 50 ft-lbs / 67.8 Nm.

To adjust the anti-scalp rollers

The anti-scalp rollers keep the cutting deck in the

correct position on the ground and prevent lawn

scalping in most terrain conditions. The anti-scalp

rollers can be set in 3 positions for different lengths

of grass:

• Top position: 1.5–2.5 in. / 38–64 mm grass.

• Middle position: 2.5–4 in. / 64–102 mm grass.

• Bottom position: 4–5 in. / 102–127 mm grass.

1. Park the product on level ground and stop the

engine.

2. Remove the nut, the bolt, the axle and the anti-

scalp roller.

3. Install the anti-scalp roller in one of the 3

positions.

CAUTION: The cutting deck can

become damaged if the anti-scalp

rollers are incorrectly adjusted. The

anti-scalp rollers must be

approximately 1/4 in. / 6.4 mm from

the ground.

1741 - 001 - 08.11.2021 19

To adjust the parallelism of the

cutting deck

This procedure will set the cutting deck in a standard

position.

1. Make sure that the tire pressure is correct. Refer

to

Tire pressure on page 19

.

2. Park the product on a level surface.

3. Turn the outer blade tips to align with the cutting

deck side to side.

WARNING: The blades on the

cutting deck are sharp and can

cause injury. Use protective gloves.

4. Measure the distance between the ground and

the bottom of the blade tip on the discharge side

of the cutting deck. Make a note of the distance.

5. Measure the distance between the ground and

the bottom of the blade tip on the side opposite

to the discharge side. The distance must be the

same as the distance for the discharge side. If

adjustment is necessary, adjust the locknut on

the top of the rear links until the 2 side to side

distances are equal.

6. Turn the 2 outer blades to align with the cutting

deck front to rear.

7. Adjust the 2 front bolts until the rear blade tips

are set 1/8–3/8 in. / 3.2-9.5 mm higher in the rear

than in the front blade tips.

8. Measure the distances again to make sure that

the cutting deck has been adjusted correctly.

To examine the blades

CAUTION: Damaged or incorrectly

balanced blades can cause damage to

the product. Replace damaged blades.

Let an approved service agent help you

sharpen and balance blunt blades.

• Look at the blades to see if they are damaged

and if it is necessary to sharpen them.

To replace the blades

1. Remove the blade bolt.

2. Assemble the new blade with the side without

stamps in the direction of the cutting deck.

WARNING: Incorrect blade type

can cause objects to eject from the

cutting deck and cause serious

injury. Use only approved blades.

3. Attach the blade bolt. Torque the bolt to 61-75

Nm.

To remove the deck belt

Park the product on level ground and engage the

parking brake before you do this task.

1. Set the cutting deck in the lowest position.

2. Remove the 2 belt covers.

3. Remove dirt and unwanted materials from

around the cutter housings and the cutting deck

surface.

20 1741 - 001 - 08.11.2021

La pagina sta caricando ...

Husqvarna Z454XS Zero Turn Lawn Mower Manuale utente

Husqvarna Z454XS Zero Turn Lawn Mower Manuale utente

in altre lingue