IBT Technologies IB881 Manuale utente

IB881

Intel Pentium® M

3.5-inch Disk Size SBC

USER’S MANUAL

Version 1.0A

ii

IB881 User’s Manual

Acknowledgments

Award is a registered trademark of Award Software International, Inc.

PS/2 is a trademark of International Business Machines Corporation.

Intel and Pentium M are registered trademarks of Intel Corporation.

Microsoft Windows is a registered trademark of Microsoft Corporation.

Winbond is a registered trademark of Winbond Electronics Corporation.

All other product names or trademarks are properties of their respective

owners.

IB881 User’s Manual iii

Table of Contents

Introduction.......................................................1

Product Description.............................................................1

Checklist..............................................................................2

IB881 Specifications...........................................................3

Board Dimensions...............................................................4

Installations.......................................................5

Installing the CPU...............................................................6

Installing the Memory.........................................................7

Setting the Jumpers .............................................................8

Connectors on IB881.........................................................11

BIOS Setup.......................................................21

Drivers Installation......................................45

Intel Chipset Software Intallation Utility..........................46

VGA Drivers Installation ..................................................48

AC97 Codec Audio Driver Installation.............................49

Intel PRO LAN Drivers Installation..................................50

Appendix...........................................................51

A. I/O Port Address Map...................................................51

B. Interrupt Request Lines (IRQ)......................................52

C. Watchdog Timer Configuration....................................53

D. IB881 CMOS Backup Feature .....................................56

iv

IB881 User’s Manual

This page is intentionally left blank.

INTRODUCTION

IB881 User’s Manual 1

Introduction

Product Description

The IB881 3.5-inch disk size SBC incorporates the Intel® advanced

855GME/852GM Chipset that contains two core components: the Memory

Controller Hub (GMCH) and ICH4. The GMCH integrates a 400MHz Pentium®

M processor front side bus controller, integrated graphics controller hub,

integrated LVDS interface, two digital video out ports multiplexed with an AGP

4x controller, a 200/266/ 333MHz DDR-SDRAM controller, and a high-speed

accelerated hub architecture interface for communication with the ICH4.

The ICH4 integrates an Ultra ATA 100/66/33 controller, USB host controller

that supports the USB 1.1 and USB 2.0 specification, LPC interface, FWH Flash

BIOS interface controller, AC’97 digital controller and a hub interface for

communication with the GMCH.

The Pentium M processor is a higher performance, lower power processor with

several microarchitectural enhancements over existing Intel low-power

processors. Some key features of the Pentium M processor microarchitecture

include dynamic execution, data pre-fetch logic, 400MHz source-synchronous

Front Side Bus (FSB), on-die 1 Mbyte second level cache (on-die 512Kbyte

second level cache on Celeron M processor) with advanced transfer cache

architecture, streaming SIMD extensions 2 (SSE2), and Enhanced Intel

SpeedStep technology.

IB881 FEATURES:

- Intel® 82855GME/82852GM chipset

- Supports Intel® Pentium® M, Celeron® M

- SO-DIMM socket supports up to 1GB DDR SDRAM

- 10/100 BaseT Ethernet with RJ45 connector

- 24-bit LVDS, VGA CRT support

- USB x4, RS232 COM x2, PS/2 Mouse/Keyboard

- IDE x2, FDD, LPT, 12V power connector, PC/104+

- 102.24mm x 148.03mm

INTRODUCTION

2

IB881 User’s Manual

Checklist

Your IB881 package should include the items listed below.

• The IB881 Pentium® M 3.5-inch Disk Size SBC

• This User’s Manual

• 1 CD containing chipset drivers and flash memory utility

• Options:

• IB32 - Cable kit with IDE, COM, Printer, Audio, USB, PS/2 Y cable

• IB33 - Kit with ATX power switch, power cable

• IB881SW-R - ATX power switch board for IB881

• IB881PW-R - ATX power board for IB881

• ICOOL010-P – Heatsink for IB881 (Socket 478)

INTRODUCTION

IB881 User’s Manual 3

IB881 Specifications

[

Product Name IB881

Form Factor 3 1/2 little board

Processor Intel Pentium M /Celeron M Processor

CPU Voltage 0.7~1.7V(IMVP4)

System Speed Pentium M/Celeron M 900MHz-1.7GHz (Low-Power,

Low-voltage)

CPU External Clock

/ FSB 400MHz

Green /APM APM1.2

CPU Socket None

Major Chipset Intel 82855GME/82852GM chipset

Intel GMCH 82855GME/82852GM 732-pin uFCBGA

Intel ICH4 82801DB 421-pin BGA

Intel FWH 82802ABA or compatible

BIOS Phoenix/Award ROM

Cache 256K/1M Level2 (CPU integrated)

Memory One SO-DIMM socket for DDR SDRAM Module; 2.5V

Support

Super I/O Winbond 83627 1 Parallel (LPT1)*1 Serial*2 (COM1 &

COM2); FDC 2.88MB (3 Mode Support)

Onboard VGA Intel GMCH 82855GME/82852GM 732-pin uFCBGA

integrated support CRT and LVDS ;

Keyboard/Mouse

Controller Winbond 83627HF built-in

Dual IDE Channel Primary/Secondary IDE Channel support 44pin for HDD

and CDROM

Onboard PC104+ PC104+ connector support four master PCI Bus/ 32 Bits

@ 33MHz

Onboard LAN Intel 82562ET 10 /100 BaseT support, full duplex

1xRJ-45 connector and 2x LED (LINK /Active on front

panel

USB Total 4 ports 2 USB ports connector for front panel and

2 ports for pin header

Keyboard / Mouse Combo PS/2 Type (Keyboard & Mouse) signal both on

connector

INTRODUCTION

4

IB881 User’s Manual

Board Dimensions

INSTALLATIONS

IB881 User’s Manual 5

Installations

This section provides information on how to use the jumpers and

connectors on the IB881 in order to set up a workable system. The topics

covered are:

Installing the CPU........................................................................ 6

Installing the Memory.................................................................. 7

Setting the Jumpers...................................................................... 8

Connectors on IB881 ................................................................. 11

INSTALLATIONS

6

IB881 User’s Manual

Installing the CPU

The IB881 board supports a Socket 479 processor socket for Intel®

Pentium® M or Celeron® M processors.

The processor socket comes with a screw to secure the processor. As

shown in the left picture below, loosen the screw first before inserting

the processor. Place the processor into the socket by making sure the

notch on the corner of the CPU corresponds with the notch on the inside

of the socket. Once the processor has slide into the socket, fasten the

screw. Refer to the figures below.

NOTE: Ensure that the CPU heat sink and the CPU top surface are in

total contact to avoid CPU overheating problem that would

cause your system to hang or be unstable.

INSTALLATIONS

IB881 User’s Manual 7

Installing the Memory

The IB881 board supports one SODIMM DDR memory socket for a

maximum total memory. The memory module capacities supported are

128MB, 256MB, 512MB and 1GB.

Installing and Removing Memory Modules

To install the DDR modules, locate the memory slot on the board and

perform the following steps:

1. Hold the DDR module so that the key of the DDR module align with

those on the memory slot. Insert the module into the socket at a slight

angle (approximately 30 degrees). Note that the socket and module

are both keyed, which means that the module can be installed only in

one direction.

2. To seat the memory module into the socket, apply firm and even

pressure to each end of the module until you feel it slip down into the

socket.

3. With the module properly seated in the socket, rotate the module

downward. Continue pressing downward until the clips at each end

lock into position.

4. To remove the DDR module, press the clips with both hands.

INSTALLATIONS

8

IB881 User’s Manual

Setting the Jumpers

Jumpers are used on IB881 to select various settings and features

according to your needs and applications. Contact your supplier if you

have doubts about the best configuration for your needs. The following

lists the connectors on IB881 and their respective functions.

Jumper Locations on IB881............................................................9

JP2: Clear CMOS Setting.............................................................10

JP6: LVDS VDD Select (5V / 3.3V)............................................10

JP8: AT/ATX Power Mode Setting..............................................10

INSTALLATIONS

IB881 User’s Manual 9

Jumper Locations on IB881

Jumpers on IB881......................................................................Page

JP2: Clear CMOS Setting............................................................. 10

JP6: LVDS VDD Select (5V / 3.3V)............................................ 10

JP8: AT/ATX Power Mode Setting.............................................. 10

INSTALLATIONS

10

IB881 User’s Manual

JP2: Clear CMOS Setting

Use JP2 to clear the CMOS contents. Note that the power connector

should be disconnected from the board before clearing CMOS.

JP2 Function

Normal (default)

Clear CMOS

JP6: LVDS VDD Select (5V / 3.3V)

JP6 VDD Setting

3.3V

5V

[

JP8: AT/ATX Power Mode Setting

JP8 Setting Power Mode

1-2, 3-4 Short ATX Mode (default)

2-3 Short AT Mode

INSTALLATIONS

IB881 User’s Manual 11

Connectors on IB881

The connectors on IB881 allows you to connect external devices such as

keyboard, floppy disk drives, hard disk drives, printers, etc. The

following table lists the connectors on IB881 and their respective

functions.

Connector Locations on IB881..................................................... 12

CN1: Floppy Drive Connector ..................................................... 13

CN2: VGA CRT Connector ......................................................... 13

CN3:RJ45 Connector ................................................................... 13

CN4: PS/2 Keyboard and Mouse Connector................................ 14

CN5, J6: USB Connectors............................................................ 14

CN6, J11: Serial Ports.................................................................. 14

CN7: PC104+ Connector.............................................................. 15

PC/104-Plus Bus Signal Assignments.......................................... 15

J2, J3: IDE Connectors................................................................. 16

J8: Parallel Port Connector........................................................... 17

J9: IrDA Connector...................................................................... 17

J12: External Audio Connector.................................................... 17

J13, J24: LVDS Connectors (1st channel, 2nd channel).............. 18

J21: Function Connector .............................................................. 18

J23: Power DC-In......................................................................... 19

J27: Buzzer Connector ................................................................. 19

INSTALLATIONS

12

IB881 User’s Manual

Connector Locations on IB881

Connectors on IB881................................................................ Page

CN1: Floppy Drive Connector......................................................13

CN2: VGA CRT Connector..........................................................13

CN3: RJ45 Connector...................................................................13

CN4: PS/2 Keyboard and Mouse Connector................................14

CN5, J6: USB Connectors............................................................14

CN6, J11: Serial Ports...................................................................14

CN7: PC104+ Connector..............................................................15

PC/104-Plus Bus Signal Assignments..........................................15

J2, J3: IDE Connectors.................................................................16

J8: Parallel Port Connector...........................................................17

J9: IrDA Connector ......................................................................17

J12: External Audio Connector ....................................................17

J13, J24: LVDS Connectors (1st channel, 2nd channel) ..............18

J21: Function Connector...............................................................18

J23: Power DC-In.........................................................................19

J27: Buzzer Connector..................................................................19

INSTALLATIONS

IB881 User’s Manual 13

CN1: Floppy Drive Connector

CN1 is a slim 26-pin connector and will support up to 2.88MB FDD.

Signal Name Pin # Pin # Signal Name

VCC 1 2 INDEX

VCC 3 4 DRV_SEL

VCC 5 6 DSK_CH

NC 7 8 NC

NC 9 10 MOTOR

DINST 11 12 DIR

NC 13 14 STEP

GND 15 16 WDATA

GND 17 18 WGATE

GND 19 20 TRACK

NC 21 22 WPROT

GND 23 24 RDATA

GND 25 26 SIDE

CN2: VGA CRT Connector

[ Signal Name Pin Pin Signal Name

Red 1 2 Green

Blue 3 4 NC

GND 5 6 GND

GND 7 8 GND

Vcc 9 10 GND

N.C. 11 12 DDCDA

HSYNC 13 14 VSYNC

DDCCLK 15

CN3: RJ45 Connector

Pin # Signal Name

1 TD+

2 TD-

3 RD+

4 RJ45-4A

5 RJ45-5A

6 RD-

7 RJ45-7A

8 RJ45-8A

INSTALLATIONS

14

IB881 User’s Manual

CN4: PS/2 Keyboard and Mouse Connector

CN4 uses a Y-cable with dual D-connectors for a PS/2 keyboard and a

PS/2 mouse.

Pin # Signal Name

1 Mouse data

2 Keyboard data

3 Ground

4 Vcc

5 Mouse Clock

6 Keyboard Clock

CN5, J6: USB Connectors

The J6 USB pin header connector supports two USB 2.0 ports via an

optional USB cable. The IB881 also supports an embedded USB

connector, CN5, which supports another two USB ports.

Signal Name Pin Pin Signal Name

Vcc 1 5 Ground

USB0- 2 6 USB1+

USB0+ 3 7 USB1-

Port1

Port2

CN5

J6 Ground 4 8 Vcc

CN6, J11: Serial Ports

Pin # Signal Name (RS-232)

1 DCD, Data carrier detect

2 RXD, Receive data

3 TXD, Transmit data

4 DTR, Data terminal ready

5 Ground

6 DSR, Data set ready

7 RTS, Request to send

8 CTS, Clear to send

9 RI, Ring indicator

10 No Connect.

CN6 is the D-sub type COM1 serial port connector, while J11 (COM2)

is a pin header type COM2 serial port connector.

INSTALLATIONS

IB881 User’s Manual 15

CN7: PC104+ Connector

PC/104-Plus Bus Signal Assignments

J3/P3

Pin A B C D

1 GND/5.0V KEY² Reserved +5 AD00

2 VI/O AD02 AD01 +5V

3 AD05 GND AD04 AD03

4 C/BE0* AD07 GND AD06

5 GND AD09 AD08 GND

6 AD11 VI/O AD10 M66EN

7 AD14 AD13 GND AD12

8 +3.3V C/BE1* AD15 +3.3V

9 SERR* GND SB0* PAR

10 GND PERR* +3.3V SDONE

11 STOP* +3.3V LOCK* GND

12 +3.3V TRDY* GND DEVSEL*

13 FRAME* GND IRDY* +3.3V

14 GND AD16 +3.3V C/BE2*

15 AD18 +3.3V AD17 GND

16 AD21 AD20 GND AD19

17 +3.3V AD23 AD22 +3.3V

18 IDSEL0 GND IDSEL1 IDSEL2

19 AD24 C/BE3* VI/O IDSEL3

20 GND AD26 AD25 GND

21 AD29 +5V AD28 AD27

22 +5V AD30 GND AD31

23 REQ0* GND REQ1* VI/O

24 GND REQ2* +5V GNT0*

25 GNT1* VI/O GNT2* GND

26 +5V CLK0 GND CLK1

27 CLK2 +5V CLK3 GND

28 GND INTD* +5V RST*

29 +12V INTA* INTB* INTC*

30 -12V Reserved Reserved GND/3.3V

KEY²

* The shaded area denotes power or ground signals.

* The KEY pins are to guarantee proper module installation. Pin-A1 will

be removed and the female side plugged for 5.0V I/O signals and

Pin-D30 will be modified in the same manner for 3.3V I/O. It is

recommended that both KEY pins (A1 and D30) be electrically

connnected for GND for shielding.

BIOS SETUP

16

IB881 User’s Manual

J2, J3: IDE Connectors

J2 is the primary IDE connector and J3 is the secondary IDE connector.

Signal Name Pin # Pin # Signal Name

Reset IDE 1 2 Ground

Host data 7 3 4 Host data 8

Host data 6 5 6 Host data 9

Host data 5 7 8 Host data 10

Host data 4 9 10 Host data 11

Host data 3 11 12 Host data 12

Host data 2 13 14 Host data 13

Host data 1 15 16 Host data 14

Host data 0 17 18 Host data 15

Ground 19 20 Key

DRQ0 21 22 Ground

Host IOW 23 24 Ground

Host IOR 25 26 Ground

IOCHRDY 27 28 Host ALE

DACK0 29 30 Ground

IRQ14 31 32 No connect

Address 1 33 34 No connect

Address 0 35 36 Address 2

Chip select 0 37 38 Chip select 1

Activity 39 40 Ground

Vcc 41 42 Vcc

Ground 43 44 N.C.

La pagina sta caricando ...

IBT Technologies IB881 Manuale utente

IBT Technologies IB881 Manuale utente

in altre lingue