HOTPOINT/ARISTON RSSF 603 EU Guida utente

Categoria
Lavatrici
Tipo
Guida utente
1
GB
WASHING MACHINE
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 4
Cutting off the water and electricity supplies
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and tips, 5
General safety
Disposal
Opening the porthole door manually
Description of the washing machine, 6-7
Control panel
Display
Running a wash cycle, 8
Wash cycles and options, 9
Table of programmes and wash cycles
Wash option
Detergents and laundry, 10
Detergent dispenser drawer
Preparing the laundry
Special wash cycles
Load balancing system
Troubleshooting, 11
Service, 12
RSSF 603
Instructions for use
English,1
GB
Polski,13
PL
Italiano,25
IT
Українська,37
UA
2
GB
Installation
! This instruction manual should be kept in a
safe place for future reference. If the washing
machine is sold, transferred or moved, make
sure that the instruction manual remains with
the machine so that the new owner is able to
familiarise himself/herself with its operation
and features.
! Read these instructions carefully: they
contain vital information relating to the safe
installation and operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its
packaging.
2. Make sure that the washing machine has
not been damaged during the transportation
process. If it has been damaged, contact the
retailer and do not proceed any further with
the installation process.
3. Remove the 4
protective screws
(used during
transportation)
and the rubber
washer with the
corresponding
spacer, located on
the rear part of the
appliance (see figure).
4. Close off the holes using the plastic plugs
provided.
5. Keep all the parts in a safe place: you will
need them again if the washing machine
needs to be moved to another location.
! Packaging materials should not be used as
toys for children.
Levelling
1. Install the washing
machine on a flat
sturdy floor, without
resting it up against
walls, furniture
cabinets or anything
else.
2. If the floor is not perfectly level, compensate
for any unevenness by tightening or loosening
the adjustable front feet (see figure); the angle
of inclination, measured in relation to the
worktop, must not exceed 2°.
Levelling the machine correctly will provide
it with stability, help to avoid vibrations and
excessive noise and prevent it from shifting
while it is operating. If it is placed on carpet or
a rug, adjust the feet in such a way as to allow
a sufficient ventilation space underneath the
washing machine.
Connecting the electricity and
water supplies
Connecting the water inlet hose
1. Connect the inlet
hose by screwing it to
a cold water tap using
a 3/4 gas threaded
connection (see
figure).
Before performing
the connection, allow
the water to run freely
until it is perfectly
clear.
2. Connect the
inlet hose to the
washing machine by
screwing it onto the
corresponding water
inlet of the appliance,
which is situated on
the top right-hand
side of the rear part
of the appliance (see
figure).
3. Make sure that the hose is not folded over
or bent.
! The water pressure at the tap must fall within
the range of values indicated in the Technical
data table (see next page).
! If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
3
GB
Connecting the drain hose
Connect the drain
hose, without bending
it, to a drain duct or
a wall drain situated
between 65 and 100
cm from the floor.
Alternatively, place
the drain hose
over the edge of
a washbasin or
bathtub, by fastening
the guide (which
can be purchased
at the technical
assistance centre) to
the tap (see figure).
The free end of the
hose should not be underwater.
! We advise against the use of hose extensions;
if it is absolutely necessary, the extension must
have the same diameter as the original hose
and must not exceed 150 cm in length.
Electrical connections
Before plugging the appliance into the
electricity socket, make sure that:
• thesocketisearthedandcomplieswithall
applicable laws;
• thesocketisabletowithstandthe
maximum power load of the appliance as
indicated in the Technical data table (see
opposite);
• thepowersupplyvoltagefallswithinthe
values indicated in the Technical data table
(see opposite);
• thesocketiscompatiblewiththeplugof
the washing machine. If this is not the case,
replace the socket or the plug.
! The washing machine must not be installed
outdoors, even in covered areas. It is
extremely dangerous to leave the appliance
exposed to rain, storms and other weather
conditions.
! When the washing machine has been
installed, the electricity socket must remain
within easy reach.
65 - 100 cm
! Do not use extension cords or multiple sockets.
! The cable should not be bent or compressed.
! The power supply cable must only be
replaced by authorised technicians.
Warning! The company shall not be held
responsible in the event that these standards
are not observed.
The first wash cycle
Once the appliance has been installed, and
before you use it for the first time, run a wash
cycle with detergent and no laundry, using
wash cycle auto clean (see “Cleaning the
washing machine”).
Technical data
Model
RSSF 603
Dimensions
width 59.5 cm
height 85 cm
depth 42,5 cm
Capacity
from 1 to 6 kg
Electrical
connections
please refer to the technical
data plate fixed to the ma-
chine
Water con-
nections
maximum pressure
1 MPa (10 bar)
minimum pressure
0.05 MPa (0.5 bar)
drum capacity 40 litres
Spin speed
up to 1000 rotations per
minute
Test wash
cycles in
accordance
with re-
gulations
1061/2010
1015/2010
programme 9
;
Eco Cotton 60°C.
programme 9
;
Eco Cotton 40°C.
This appliance conforms to
the following EC Directives:
- EMC - 2014/30/EU (Elec-
tromagnetic Compatibility)
- LVD - 2014/35/EU (Low
Voltage)
- 2012/19/EU (WEEE)
4
GB
Care and maintenance
Cutting off the water and
electricity supplies
•Turnoffthewatertapaftereverywashcycle.
This will limit wear on the hydraulic system
inside the washing machine and help to
prevent leaks.
•Unplugthewashingmachinewhencleaning
it and during all maintenance work.
Cleaning the washing machine
•Theouterpartsandrubbercomponents
of the appliance can be cleaned using a soft
cloth soaked in lukewarm soapy water. Do not
use solvents or abrasives.
•Thewashingmachinehasaautoclean
programme for its internal parts that must be
run with no load in the drum.
To help the wash cycle
you may want to use
either the detergent
(i.e. a quantity 10%
the quantity specified
for lightly-soiled
garments) or special
additives to clean the
washing machine. We
recommend running a
cleaning programme every 40 wash cycles.
To start the programme press button A for 5
seconds (see figure).
The programme will start automatically and will
run for about 70 minutes. To stop the cycle
press the START/PAUSE button.
Cleaning the detergent dispenser
drawer
Remove the dispenser
by raising it and
pulling it out (see
figure).
Wash it under running
water; this operation
should be repeated
frequently.
Caring for the door and drum of
your appliance
•Alwaysleavetheportholedoorajarinorder
to prevent unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-
cleaning pump which does not require any
maintenance. Sometimes, small items (such as
coins or buttons) may fall into the pre-chamber
which protects the pump, situated in its bottom
part.
! Make sure the wash cycle has finished and
unplug the appliance.
To access the pre-chamber:
1. using a
screwdriver, remove
the cover panel on
the lower front part of
the washing machine
(see figure);
2. unscrew the lid
by rotating it anti-
clockwise (see figure):
a little water may
trickle out. This is
perfectly normal;
3. clean the inside thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks
are securely in place before you push it onto
the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If
there are any cracks, it should be replaced
immediately: during the wash cycles, water
pressure is very strong and a cracked hose
could easily split open.
! Never use second-hand hoses.
1
2
A
5
GB
Precautions and tips
! This washing machine was designed and constructed
in accordance with international safety regulations. The
following information is provided for safety reasons and
must therefore be read carefully.
General safety
• Thisappliancewasdesignedfordomesticuseonly.
This appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given
supervision or instruction concerning use of
the appliance in a safe way and understand
the hazards involved. Children shall not
play with the appliance. Cleaning and user
maintenance shall not be made by children
without supervision.
• Donottouchthemachinewhenbarefootorwithwetor
damp hands or feet.
• Donotpullonthepowersupplycablewhenunplugging
the appliance from the electricity socket. Hold the plug
and pull.
• Donotopenthedetergentdispenserdrawerwhilethe
machine is in operation.
• Donottouchthedrainedwaterasitmayreach
extremely high temperatures.
Neverforcetheportholedoor.Thiscoulddamagethesafety
lock mechanism designed to prevent accidental opening.
• Iftheappliancebreaksdown,donotunderany
circumstances access the internal mechanisms in an
attempt to repair it yourself.
• Alwayskeepchildrenwellawayfromtheappliancewhile
it is operating.
• Thedoorcanbecomequitehotduringthewashcycle.
• Iftheappliancehastobemoved,workinagroupoftwo
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.
• Beforeloadinglaundryintothewashingmachine,make
sure the drum is empty.
Disposal
•Disposingofthepackagingmaterials:observelocal
regulations so that the packaging may be re-used.
•TheEuropeanDirective2012/19/EUonWasteElectrical
and Electronic Equipment, requires that old household
electrical appliances must not be disposed of in the
normal unsorted municipal waste stream. Old appliances
must be collected separately in order to optimise the
recovery and recycling of the materials they contain and
reduce the impact on human health and the environment.
The crossed out “wheeled bin” symbol on the product
reminds you of your obligation, that when you dispose of
the appliance it must be separately collected. Consumers
should contact their local authority or retailer for information
concerning the correct disposal of their old appliance.
Opening the porthole door manually
In the event that it is not possible to open the porthole
door due to a powercut, and if you wish to remove the
laundry, proceed as follows:
1. remove the plug from the
electrical socket.
2. make sure the water level
inside the machine is lower
than the door opening; if
it is not, remove excess
water using the drain hose,
collecting it in a bucket as
indicated in the figure.
3. using a screwdriver,
remove the cover panel on
the lower front part of the
washing machine (see figure).
4. pull outwards using the tab as indicated in the figure,
until the plastic tie-rod is freed from its stop position; pull
downwards and open the door at the same time.
5. reposition the panel, making sure the hooks are securely
in place before you push it onto the appliance.
20
6
GB
Description of the washing
machine
Control panel
Detergent dispenser drawer: used to dispense
detergents and washing additives ( see “Detergents and
laundry”).
ON/OFF button: press this briefly to switch the
machine on or off. The START/PAUSE indicator light which
flashes slowly in a green colour shows that the machine is
switched on. To switch off the washing machine during the
wash cycle, press and hold the button for approximately 3
seconds; if the button is pressed briefly or accidentally the
machine will not switch off.
If the machine is switched off during a wash cycle, this
wash cycle will be cancelled.
WASH CYCLE SELECTOR KNOB: used to set the
desired wash cycle (see “Table of programmes and wash
cycles”).
OPTION button and indicator light: press to select the
available options. The indicator light corresponding to the
selected option will remain lit.
CLEANING ACTION button and indicator light
: to
select the desired wash intensity.
TEMPERATURE button: press to reduce or completely
exclude the temperature; the value appears on the display.
SPIN button: press to reduce or completely exclude
the spin cycle; the value appears on the display.
DELAY TIMER button: press to set a delayed start for
the selected wash cycle; the delay period appears on the
display.
START/PAUSE button and indicator light: when the green
indicator light flashes slowly, press the button to start a
wash cycle. Once the cycle has begun the indicator light
will remain lit in a fixed manner. To pause the wash cycle,
press the button again; the indicator light will flash in an
amber colour. If the symbol is not illuminated, the door
may be opened. To start the wash cycle from the point at
which it was interrupted, press the button again.
CHILD LOCK button: to activate the control panel lock,
press and hold the button for approximately 2 seconds.
When the indicator light is illuminated, the control
panel is locked (apart from the ON/OFF button). This
means it is possible to prevent wash cycles from being
modified accidentally, especially where there are children in
the home. To deactivate the control panel lock, press and
hold the button for approximately 2 seconds.
Standby mode
This washing machine, in compliance with new energy
saving regulations, is fitted with an automatic standby
system which is enabled after about 30 minutes if no
activity is detected. Press the ON-OFF button briefly and
wait for the machine to start up again.
Antimicrobial seal
The seal around the porthole door is made from a special
mixture ensuring antimicrobial protection, thus reducing
bacterial proliferation up to 99.99%.
The seal contains zinc pyrithione, a biocidal substance
which reduces the proliferation of harmful microbes (*)
such as batteries and mould prone to causing stains,
unpleasant odours and product deterioration.
(*) According to tests performed by the University of Perugia,
Italy on: Staphylococcus aureus, Escherichia coll, Pseudomonas
aeruginosa, Candida albicans, Aspergillus niger, Penicillium digitatum.
In rare cases an allergic reaction may be caused by prolonged contact between
seal and skin.
OPTION
button and
indicator light
CHILD
LOCK
button
TEMPERATURE
button
WASH
CYCLE
SELECTOR
KNOB
Detergent dispenser drawer
ON/OFF
button
SPIN
button
START/PAUSE
button and indicator
light
DISPLAY
DELAY
TIMER
button
CLEANING
ACTION
button and
indicator light
7
GB
Display
The display is useful when programming the machine and provides a great deal of information.
The duration of the available wash cycles and the remaining time of a running cycle appear (the display will show the
maximum duration of the cycle chosen, which may decrease after several minutes, since the effective duration of the
programme varies depending on the wash load and the settings chosen); if the DELAY TIMER option has been set, the
countdown to the start of the selected wash cycle will appear.
Pressing the corresponding button allows you to view the maximum spin speed and temperature values attained by the
machine during the set wash cycle, or the values selected most recently, if these are compatible with the set wash cycle.
DOOR LOCKED indicator light:
The lit symbol indicates that the door is locked. To prevent any damage, wait until the symbol turns off before opening the door.
To open the door while a cycle is in progress, press the START/PAUSE button; if the DOOR LOCKED symbol is switched
off the door may be opened.
8
GB
Running a wash cycle
1. SWITCH THE MACHINE ON. Press the button;
the START/PAUSE indicator light will flash slowly in a
green colour.
2. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed
the maximum load value indicated in the table of
programmes and wash cycles on the following page.
3. MEASURE OUT THE DETERGENT. Pull out the
detergent dispenser drawer and pour the detergent into
the relevant compartments as described in “Detergents
and laundry”.
4. CLOSE THE DOOR.
5. SELECT THE WASH CYCLE. Use the WASH CYCLE
SELECTOR knob to select the desired wash cycle. A
temperature and spin speed is set for each wash cycle;
these values may be adjusted. The duration of the cycle
will appear on the display.
6. CUSTOMISE THE WASH CYCLE. Use the relevant
buttons:
Modify the temperature and/or spin speed.
The machine automatically displays the maximum
temperature and spin speed values set for the selected
cycle, or the most recently-used settings if they are
compatible with the selected cycle. The temperature
can be decreased by pressing the button, until
the cold wash “OFF” setting is reached. The spin
speed may be progressively reduced by pressing
the button, until it is completely excluded (the
“OFF” setting). If these buttons are pressed again, the
maximum values are restored.
! Exception: if the 3 programme is selected, the
temperature can be increased up to a value of 90°C.
! Exception: if the 4 programme is selected, the
temperature can be increased up to a value of 60°C.
Setting a delayed start.
To set a delayed start for the selected cycle, press the
corresponding button repeatedly until the required delay
period has been reached. When this option has been
activated, the symbol lights up on the display. To
remove the delayed start setting, press the button until
the text “OFF” appears on the display.
Set the desired wash intensity.
Option makes it possible to optimise washing based
on the level of soil in the fabrics and on desired wash
cycle intensity.
For heavily-soiled garments press button until
the “Intensive” level is reached. This level ensures
a high-performance wash due to a larger quantity of
water used in the initial phase of the cycle and due to
increased drum rotation. It is useful when removing the
most stubborn stains.
It can be used with or without bleach. If you desire
bleaching, insert the extra tray compartment 3.
When pouring in the bleach, be careful not to exceed
the “max” level marked on the central pivot (see figure
pag. 10).
For lightly-soiled garments or a more delicate treatment
of the fabrics, press button until the “Delicate
level is reached. The cycle will reduce drum rotation
to ensure washing results that are perfect for delicate
garments.
Modify the cycle settings.
• Pressthebuttontoenabletheoption;theindicator
light corresponding to the button will switch on.
• Pressthebuttonagaintodisabletheoption;the
indicator light will switch off.
! If the selected option is not compatible with the set
wash cycle, the indicator light will flash and the option
will not be activated.
! The options may affect the recommended load value
and/or the duration of the cycle.
7. START THE WASH CYCLE. Press the START/
PAUSE button. The corresponding indicator light will
turn green, remaining lit in a fixed manner, and the
door will be locked (the DOOR LOCKED symbol will
be lit). To change a wash cycle while it is in progress,
pause the washing machine using the START/PAUSE
button (the START/PAUSE indicator light will flash
slowly in an amber colour); then select the desired cycle
and press the START/PAUSE button again.
To open the door while a cycle is in progress, press
the START/PAUSE button; if the DOOR LOCKED
symbol is switched off the door may be opened. Press
the START/PAUSE button again to restart the wash
cycle from the point at which it was interrupted.
8. THE END OF THE WASH CYCLE. This will be
indicated by the text “END” on the display; when the
DOOR LOCKED symbol switches off the door may
be opened. Open the door, unload the laundry and
switch off the machine.
! If you wish to cancel a cycle which has already begun,
press and hold the button. The cycle will be stopped
and the machine will switch off.
9
GB
Wash cycles and options
Wash options
! If the selected option is not compatible with the set
wash cycle, the indicator light will flash and the option
will not be activated.
Extra Rinse
By selecting this option, the efficiency of the rinse is
increased and optimal detergent removal is guaranteed. It
is particularly useful for sensitive skin.
Table of programmes and wash cycles
1) Test wash cycle in compliance with regulations 1061/2010: set wash cycle 9 with a temperature of 60°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be washed at
60°C . The actual washing temperature may differ from the indicated value.
2) Test wash cycle in compliance with regulations 1061/2010: set wash cycle 9 with a temperature of 40°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be washed at
40°C . The actual washing temperature may differ from the indicated value.
For all Test Institutes:
2) Long wash cycle for cottons: set programme 9 at temperature 40°C.
3) Long wash cycle for synthetics: set wash cycle 4 with a temperature of 40°C.
* If you select programme and exclude the spin cycle, the machine will drain only.
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-
ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
** The duration of the wash cycle can be checked on the display.
Wash cycles
Description of the wash cycle
Max.
temp. (°C)
Max.
speed
(rpm)
Detergents
Max. load
(kg)
Residual
dampness%
Energy con-
sumptionkWh
Total water lt
Cycle dura-
tion
Wash
Fabric
softener
Bleach
DAILY CLEAN
1
Anti Stain
40°
1000
- 4 - - -
**
2
Anti Stain Quick
40°
1000
- 3,5 - - -
**
3
Cotton: lightly soiled resistant and delicate colours.
40°
(Max. 90°C)
1000
6 - - -
**
4
Synthetics (3): lightly soiled resistant colours.
40°
(Max. 60°C)
1000
3,5 44 0,47 46 95’
5
Mix 30’: to refresh lightly soiled garments quickly (not suitable for
wool, silk and clothes which require washing by hand).
30° 800
- 3 71 0,16 39 30’
SPECIALS
6
Darks
30° 800
- 4 - - -
**
7
Delicates
30° 0
- 1 - - -
**
8
Wool: for wool, cashmere, etc.
40° 800
- 1,5 - - -
**
9
Eco Cotton 60°C
60°/4
(1): heavily soiled whites and resistant colours.
60° 1000
- 6 62 0,80 50 200’
9
Eco Cotton 40°C
60°/4
(2): lightly soiled resistant and delicate colours.
40° 1000
- 6 62 0,65 65 170’
10
Cotton 20°C: lightly soiled resistant and delicate colours.
20° 1000
6 - - -
**
EXTRA
11
Baby
40° 1000
4 - - -
**
12
Anti Allergy
60° 1000
4 - - -
**
13
Silk/Curtains: for garments in silk and viscose, lingerie. 30° 0
- 1 - - -
**
14 Padded Jackets
30° 1000
- 1 - - -
**
Partial Programmes
Rinse
- 1000
-
- 6 - - -
**
Spin and Pump out
- 1000
- - - 6 - - -
**
Pump out only *
- OFF
- - - 6 - - -
**
10
GB
Detergents and laundry
Detergent dispenser drawer
Successful washing results also depend on the correct
dose of detergent: adding too much detergent will not
necessarily result in a more efficient wash, and may in
fact cause build up on the inside of your appliance and
contribute to environmental pollution.
! Use powder detergent for white cotton garments, for pre-
washing, and for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
! Do not use hand washing detergents; they create too
much foam.
Open the detergent
dispenser drawer and pour
in the detergent or washing
additive, as follows.
! Do not pour detergent into
the middle compartment (*).
compartment 1: Detergent for the wash cycle
(powder or liquid)
If liquid detergent is used, it is recommended that the
removable plastic partition A (supplied) be used for proper
dosage. If powder detergent is used, place the partition
into slot B.
compartment 2: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
extra compartment 3: Bleach
Preparing the laundry
• Dividethelaundryaccordingto:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
• Emptyallgarmentpocketsandcheckthebuttons.
• Donotexceedthelistedvalues,whichreferto
the weight of the laundry when dry: see “Table of
programmes and wash cycles”.
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1,200 g
1 towel 150-250 g
Special wash cycles
Anti Stain: the programme 1 is suitable to heavily-soiled
garments with resistant colours. It ensures a washing class
that is higher than the standard class (A class). When running
the programme, do not mix garments of different colours. We
recommend the use of powder detergent. Pre-treatment with
special additives is recommended if there are obstinate stains.
Anti Stain Quick: this programme is ideal for washing the
most difficult daily stains in 1 hour. It is ideal for mixed fabrics
and coloured garments, caring for your clothes as it washes.
Darks: use cycle 6 to wash dark-coloured garments.
This programme is designed to maintain dark colours over
time. We recommend using a liquid detergent for the best
results when washing dark-coloured garments.
M
AX
1
3
2
A
B
*
Delicates: use programme 7 to wash very delicate
garments having strasses or sequins.
We recommend turning the garments inside out before
washing and placing small items into the special bag
for washing delicates. Use liquid detergent on delicate
garments for best results.
Wool - Woolmark Apparel Care - Green:
the wool wash cycle of this machine has been approved
by The Woolmark Company for the washing of wool
garments labelled as “hand wash” provided that the
products are washed according to the instructions on the
garment label and those issued by the manufacturer of this
washing machine (M1128)
Cotton 20°C: the programme 10 ideal for lightly soiled
cotton loads. The effective performance levels achieved at
cold temperatures, which are comparable to washing at 40°,
are guaranteed by a mechanical action which operates at
varying speed, with repeated and frequent peaks.
Baby: use the special wash cycle 11 to remove the
remove the soiling typically caused by babies, while
removing all traces of detergent from nappies in order to
prevent the delicate skin of babies from suffering allergic
reactions. The cycle has been designed to reduce the
amount of bacteria by using a greater quantity of water
and optimising the effect of special disinfecting additives
added to the detergent.
Anti Allergy: use programme 12 to remove major
allergens such as pollen, mites, cat’s and dog’s hair.
Silk: use special wash cycle 13 to wash all silk garments.
We recommend the use of special detergent which has
been designed to wash delicate clothes.
Curtains: fold curtains and place them in a pillow case or
mesh bag. Use wash cycle 13.
Padded Jackets: to wash clothes padded with goose
down (such as puffa jackets) or cushions (the total weight
of which should not exceed 1 kg), use the special 14
programme.
Load balancing system
Before every spin cycle, to avoid excessive vibrations
before every spin and to distribute the load in a uniform
manner, the drum rotates continuously at a speed which
is slightly greater than the washing rotation speed. If,
after several attempts, the load is not balanced correctly,
the machine spins at a reduced spin speed. If the load is
excessively unbalanced, the washing machine performs
the distribution process instead of spinning. To encourage
improved load distribution and balance, we recommend
small and large garments are mixed in the load.
11
GB
Troubleshooting
Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Service (see “ Service”),
make sure that the problem cannot be solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not fill
with water (the text “H2O” flashes
on the display).
The washing machine continuously
takes in and drains water.
The washing machine does not
drain or spin.
The washing machine vibrates a
lot during the spin cycle.
The washing machine leaks.
The “option and START/PAUSE
indicator lights flash rapidly and an
error code appears on the display (e.g.:
F-01, F-..).
There is too much foam.
Possible causes / Solutions:
• Theapplianceisnotpluggedintothesocketfully,ornotenoughtomakecontact.
• Thereisnopowerinthehouse.
• Thewashingmachinedoorisnotclosedproperly.
• TheON/OFFbuttonhasnotbeenpressed.
• TheSTART/PAUSEbuttonhasnotbeenpressed.
• Thewatertaphasnotbeenopened.
• Adelayedstarthasbeenset.
• Thewaterinlethoseisnotconnectedtothetap.
• Thehoseisbent.
• Thewatertaphasnotbeenopened.
• Thereisnowatersupplyinthehouse.
• Thepressureistoolow.
• TheSTART/PAUSEbuttonhasnotbeenpressed.
• Thedrainhoseisnotfittedataheightbetween65and100cmfromthefloor
(see “Installation”).
• Thefreeendofthehoseisunderwater(see “Installation”).
• Thewalldrainagesystemisnotfittedwithabreatherpipe.
If the problem persists even after these checks, turn off the water tap, switch the
appliance off and contact the Technical Assistance Service. If the dwelling is on one
of the upper floors of a building, there may be problems relating to water drainage,
causing the washing machine to fill with water and drain continuously. Special anti-
draining valves are available in shops and help to prevent this inconvenience.
• Thewashcycledoesnotincludedraining:somecyclesrequirethedraining
process to be enabled manually.
• Thedrainhoseisbent(see “Installation”).
• Thedrainageductisclogged.
• Thedrumwasnotunlockedcorrectlyduringinstallation(see “Installation”).
• Thewashingmachineisnotlevel(see “Installation”).
• Thewashingmachineistrappedbetweencabinetsandwalls(see “Installation”).
• Thewaterinlethoseisnotscrewedonproperly(see “Installation”).
• Thedetergentdispenserdrawerisblocked(forcleaninginstructions,see “Care
and maintenance”).
• Thedrainhoseisnotfixedproperly(see “Installation”).
• Switchoffthemachineandunplugit,waitforapproximately1minuteandthen
switch it back on again.
If the problem persists, contact the Technical Assistance Service.
• Thedetergentisnotsuitableformachinewashing(itshoulddisplaythetext“for
washing machines” or “hand and machine wash”, or the like).
• Toomuchdetergentwasused.
12
GB
Before contacting the Technical Assistance Service:
• Checkwhetheryoucansolvetheproblemalone(see “Troubleshooting”).
• Restartthewashcycletocheckwhethertheproblemhasbeensolved.
• Ifthisisnotthecase,contactanauthorisedTechnicalAssistanceCentre.
! Always request the assistance of authorised technicians.
Have the following information to hand:
• thetypeofproblem;
• theappliancemodel(Mod.);
• theserialnumber(S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the
front of the appliance by opening the door.
Service
13
PL
PRALKA
Spis treści
Instalacja, 14-15
Rozpakowanie i wypoziomowanie
Podłączenia hydrauliczne i elektryczne
Pierwszy cykl prania
Dane techniczne
Utrzymanie i konserwacja, 16
Odłączenie wody i prądu elektrycznego
Czyszczenie pralki
Czyszczenie szuadki na środki piorące
Konserwacja okrągłych drzwiczek i bębna
Czyszczenie pompy
Kontrola przewodu doprowadzającego wodę
Zalecenia i środki ostrożności, 17
Ogólne zasady bezpieczeństwa
Utylizacja
Ręczne otwieranie okrągłych drzwiczek
Opis pralki, 18-19
Panel sterowania
Wyświetlacz
Jak wykonać cykl prania, 20
Programy i opcje, 21
Tabela programów
Opcje prania
Środki piorące i bielizna, 22
Szuadka na środki piorące
Przygotowanie bielizny
Programy specjalne
System równoważenia wsadu
Nieprawidłowości w
działaniu i sposoby ich usuwania, 23
Serwis Techniczny, 24
RSSF 603
Instrukcja obsługi
Polski
PL
14
PL
Instalacja
! Należy zachować niniejszą książeczkę,
aby móc z niej skorzystać w każdej chwili.
W przypadku sprzedaży, odstąpienia lub
przeniesienia pralki w inne miejsce należy
zadbać o przekazanie instrukcji wraz z nią,
aby nowy właściciel mógł się zapoznać z
działaniem urządzenia i z dotyczącymi go
ostrzeżeniami.
! Należy uważnie przeczytać instrukcję
obsługi: zawiera ona ważne informacje
dotyczące instalacji oraz właściwego i
bezpiecznego użytkowania pralki.
Rozpakowanie i wypoziomowanie
Rozpakowanie
1. Rozpakować pralkę.
2. Sprawdzić, czy nie doznała ona
uszkodzeń w czasie transportu. W przypadku
stwierdzenia uszkodzeń, nie podłączać pralki
i skontaktować się ze sprzedawcą.
3. Odkręcić śruby
zabezpieczające
urządzenie na
czas transportu
oraz zdjąć gumowy
element z podkładką,
znajdujący się w
tylnej części pralki
(patrz rysunek).
4. Zatkać otwory przy pomocy plastikowych
zaślepek, znajdujących się w wyposażeniu
urządzenia.
5. Zachować wszystkie części: w razie
konieczności przewiezienia pralki w inne
miejsce, powinny one zostać ponownie
zamontowane.
! Części opakowania nie są zabawkami dla
dzieci.
Poziomowanie
1. Ustawić pralkę
na płaskiej i twardej
podłodze, nie
opierając jej o ściany,
meble itp.
2. Jeśli podłoga
nie jest idealnie
pozioma, należy
skompensować
nierówności, odkręcając lub dokręcając
przednie nóżki (patrz rysunek); kąt
nachylenia, zmierzony na górnym blacie
pralki, nie powinien przekraczać 2°.
Staranne wypoziomowanie pralki zapewnia
jej stabilność i zapobiega wibracjom,
hałasowi oraz przesuwaniu się urządzenia
w czasie pracy. W przypadku ustawienia na
dywanie lub wykładzinie dywanowej, należy
tak wyregulować nóżki, aby pod pralką
pozostawała wolna przestrzeń niezbędna dla
wentylacji.
Podłączenia hydrauliczne i
elektryczne
Podłączenie przewodu doprowadzającego
wodę
1. Podlacz przewód
zasilajacy poprzez
przykrecenie go do
zaworu zimnej wody z
konwka gwintowana
(patrz rysunek):
Przed podłączeniem
spuszczać wodę do
momentu, stanie
s ona ckowicie
przezroczysta.
2. Podłączyć do
urządzenia przewód
doprowadzający
wodę, przykręcając
go do odpowiedniego
przyłącza wody,
znajdującego się w
tylnej części pralki, z
prawej strony u góry
(patrz rysunek).
3. Zwrócić uwagę, aby przewód nie był
pozaginany ani przygnieciony.
! Ciśnienie wody w kurku powinno mieścić
się w przedziale podanym w tabeli Danych
technicznych (patrz strona obok).
! Jeśli długość przewodu doprowadzającego
wodę jest niewystarczająca, należy zwrócić
się do specjalistycznego sklepu lub do
autoryzowanego technika.
! Nigdy nie instalować przewodów, które były
już używane.
! Stosować przewody znajdujące się w
wyposażeniu urządzenia.
15
PL
Podłączenie przewodu odpływowego
Podłączyć przewód
odpływowy, nie
zginając go, do rury
ściekowej lub do
otworu odpływowego
w ścianie, które
powinny się
znajdować na
wysokości od 65 do
100 cm od podłogi.
albo oprzeć
Alternatywnie
można oprzeć rurę
odpływową na
brzegu umywalki
lub wanny,
przymocowując
prowadnicę
(można ją
zakupić w punkcie
serwisowym)
do kurka (patrz rysunek). Wolny koniec
przewodu odpływowego nie powinien być
zanurzony w wodzie.
! Odradza się używanie rur przedłużających;
jednak jeśli jest to konieczne, przedłużacz
powinien mieć taki sam przekrój, jak
oryginalna rura, a jego długość nie powinna
przekraczać 150 cm.
Podłączenie elektryczne
Przed włożeniem wtyczki do gniazdka
elektrycznego należy się upewnić, czy:
gniazdko posiada uziemienie i jest zgodne
z obowiązującymi przepisami;
gniazdko jest w stanie wytrzymać
maksymalne obciążenie mocy urządzenia,
wskazane w tabeli Danych technicznych
(patrz obok);
napięcie zasilania mieści się w wartościach
wskazanych w tabeli Danych technicznych
(patrz obok);
gniazdko pasuje do wtyczki pralki. W
przeciwnym razie należy wymienić
gniazdko lub wtyczkę.
! Nie należy instalować pralki na otwartym
powietrzu, nawet w osłoniętym miejscu,
gdyż wystawienie urządzenia na działanie
deszczu i burz jest bardzo niebezpieczne.
! Po zainstalowaniu pralki gniazdko
elektryczne powinno być łatwo dostępne.
65 - 100 cm
! Nie używać przedłużaczy ani rozgałęźników.
! Kabel nie powinien być pozginany ani
przygnieciony.
! Przewód zasilania elektrycznego może być
wymieniany wyłącznie przez autoryzowanych
techników.
Uwaga! Producent nie ponosi żadnej
odpowiedzialności, jeśli powyższe zasady
nie będą przestrzegane.
Pierwszy cykl prania
Po zainstalowaniu pralki, przed
przystąpieniem do jej użytkowania, należy
wykonać jeden cykl prania ze środkiem
piorącym, ale bez wsadu, nastawiając
program opcja czyszczenia pralki (patrz
“Czyszczenie pralki”).
Dane techniczne
Model RSSF 603
Wymiary
szerokość cm 59,5
wysokość cm 85
głębokość cm 42,5
Pojemność od 1 do 6 kg
Dane prądu
elektryczne-
go
dane techniczne umieszc-
zone są na tabliczce na
maszynie
Dane sieci
wodo-
ciągowej
Maksymalne ciśnienie
1 MPa (10 barów)
ciśnienie minimalne
0,05 MPa (0,5 barów)
pojemność bębna 40 litrów
Szybkość
wirowania
do 1000 obrotów na minutę
Programy
testowe
zgodnie z
regulamin
1061/2010 i
1015/2010
Program 9;
Bawełna Eco 60°C.
Program 9;
Bawełna Eco 40°C.
Urdzenie to zosto wy-
produkowane zgodnie z
następucymi przepisami
CE:
- EMC - 2014/30/EU (o
Kompatybilności Elektro-
magnetycznej)
- 2012/19/EU (WEEE)
- LVD - 2014/35/EU (o Ni-
skim Napięciu)
16
PL
Utrzymanie i konserwacja
Odłączenie wody i prądu
elektrycznego
Zamknąć kurek dopływu wody po każdym
praniu. W ten sposób zmniejsza się zużycie
instalacji hydraulicznej pralki oraz eliminuje
się niebezpieczeństwo wycieków.
Przed przystąpieniem do czyszczenia pralki
oraz do czynności konserwacyjnych wyjąć
wtyczkę z gniazdka.
Czyszczenie pralki
• Obudowę zewnętrzną i gumowe części
pralki można myć ściereczką zmoczoną
w letniej wodzie z mydłem. Nie stosować
rozpuszczalników ani ściernych środków
czyszczących.
• Pralka jest wyposażona w program opcja
czyszczenia pralki części wewnętrznych,
który należy przeprowadzać nie
wprowadzając niczego do kosza pralki.
Środek piorący (w ilości równej 10% ilości
zalecanej dla lekko zabrudzonej odzieży)
lub dodatki przeznaczone specjalnie do
czyszczenia pralek, mogą zostać użyte
jako środki pomocnicze podczas programu
czyszczenia. Zaleca się przeprowadzanie
programu czyszczenia co 40 cykli prania.
W celu uruchomienia
programu, należy
nacisnąć przycisk A
przez 5 sek. (zob.
rysunek).
Program rozpocznie
się automatycznie i
będzie trwał około
70 minut. W celu
zakończenia cyklu,
należy nacisnąć
przycisk START/PAUZA.
Czyszczenie szuadki na środki
piorące
Wysunąć szuadkę,
unosząc ją lekko ku
górze i wyciągając
na zewnątrz (patrz
rysunek).
Wypłukać szuadkę
pod bieżącą wodą.
Czynność tę
należy wykonywać
stosunkowo często.
Konserwacja okrągłych drzwiczek i
bębna
Drzwiczki pralki należy zawsze
pozostawiać uchylone, aby zapobiec
tworzeniu się nieprzyjemnych zapachów.
Czyszczenie pompy
Pralka wyposażona jest w pompę
samoczyszczącą, która nie wymaga
zabiegów konserwacyjnych. Może się
jednak zdarzyć, że drobne przedmioty
(monety, guziki) wpadną do komory wstępnej
zabezpieczającej pompę, która znajduje się
w jej dolnej części.
! Należy się upewnić, że cykl prania został
zakończony i wyjąć wtyczkę z gniazdka.
Aby dostać się do komory wstępnej:
1. zdjąć panel
pokrywy z przedniej
strony pralki przy
pomocy śrubokrętu
(patrz rysunek);
2. odkręcić pokrywę,
obracając ją w
kierunku przeciwnym
do ruchu wskazówek
zegara (patrz
rysunek): wypłynięcie
niewielkiej ilości
wody jest normalnym
zjawiskiem;
3. dokładnie wyczyścić wnętrze;
4. ponownie przykręcić pokrywę;
5. ponownie założyć panel upewniwszy
się, przed dociśnięciem go do maszyny,
czy zatrzaski zostały umieszczone w
odpowiednich otworach.
Kontrola przewodu
doprowadzającego wodę
Przynajmniej raz w roku należy sprawdzić
przewód doprowadzający wodę. Jeśli
widoczne są na nim pęknięcia i rysy, należy
go wymienić: w trakcie prania duże ciśnienie
może bowiem spowodować jego nagłe
rozerwanie.
! Nigdy nie instalować już używanych
przewodów.
1
2
A
17
PL
Zalecenia i środki
ostrożności
materiałów, z których są one zbudowane, oraz
aby zapobiec potencjalnym szkodom dla zdrowia
i środowiska. Symbol przekreślonego kosza jest
umieszczony na wszystkich produktach w celu
przypominania o obowiązku ich segregacji.
Właściciele urządzeń gospodarstwa domowego
mogą uzyskać dodatkowe informacje dotyczące ich
prawidłowej utylizacji, zwracając się do odpowiednich
służb publicznych lub do sprzedawców tych urządzeń.
Ręczne otwieranie okrągłych drzwiczek
Jeśli z powodu przerwy w dostawie energii elektrycznej
nie jest możliwe otwarcie okrągłych drzwiczek, w
celu wyjęcia i rozwieszenia prania należy wykonać
następujące czynności:
1. wyjąć wtyczkę z gniazdka
elektrycznego.
2. sprawdzić, czy poziom
wody wewnątrz maszyny
znajduje się poniżej poziomu
otwarcia drzwiczek; w
przeciwnym wypadku usunąć
nadmiar wody przez przewód
odpływowy, zbierając ją
do wiaderka w sposób
wskazany na rysunku.
3. zdjąć panel pokrywy z
przedniej strony pralki przy
pomocy śrubokrętu (patrz
rysunek).
4. pociągnąć na zewtrz klapkę wskazaną na rysunku, aż
do wyzwolenia się z zacisku plastikowego zaczepu; następnie
pocgnąć go w dół i wnocześnie otworzyć drzwiczki.
5. ponownie założyć panel upewniwszy się, przed
dociśnięciem go do maszyny, czy zatrzaski zostały
umieszczone w odpowiednich otworach.
! Pralka została zaprojektowana i wyprodukowana
zgodnie z międzynarodowymi normami bezpieczeństwa.
Niniejsze ostrzeżenia zostały tu zamieszczone ze
względów bezpieczeństwa i należy je uważnie przeczytać.
Ogólne zasady bezpieczeństwa
Urządzenie to zostało zaprojektowane wyłącznie do
użytkowania w warunkach domowych.
Z niniejszego urdzenia mogą korzyst
dzieci powyżej 8 roku życia i osoby o
ograniczonych zdolnciach zycznych,
zmyowych dź umyowych, jak wni
osoby nieposiadace dwiadczenia lub
znajomci urządzenia, jli znajdu się one
pod nadzorem innych osób lub jli zostały
pouczone na temat bezpiecznego sposobu
użycia urdzenia oraz zdają sobie sprawę
ze związanych z nim zagreń. Dzieci nie
powinny baw się urządzeniem. Prace
związane z czyszczeniem i konserwac nie
mogą b wykonywane przez dzieci, jli nie
są one nadzorowane.
Nie dotykać pralki stojąc przy niej boso lub mając
mokre lub wilgotne ręce albo stopy.
Nie wyjmować wtyczki z gniazdka ciągnąc za kabel,
należy trzymać za wtyczkę.
W trakcie pracy maszyny nie otwierać szuadki na
środki piorące.
Nie dotykać odprowadzanej wody, gdyż może ona być
bardzo gorąca.
W żadnym wypadku nie otwierać na siłę drzwiczek pralki:
grozi to uszkodzeniem mechanizmu zabezpieczacego
drzwiczki przed przypadkowym otwarciem.
W razie wystąpienia usterki nie należy w żadnym
wypadku ingerować w wewnętrzne części pralki z
zamiarem samodzielnego dokonania naprawy.
Zawsze uważać, aby dzieci nie zbliżały się do
pracującej pralki.
W czasie prania drzwiczki pralki nagrzewają się.
Jeśli trzeba przenieść pralkę w inne miejsce, należy to
robić bardzo ostrożnie, w dwie lub trzy osoby. Nigdy
nie należy samodzielnie przenosić urządzenia, gdyż
jest ono bardzo ciężkie.
Przed włożeniem bielizny sprawdzić, czy bęben jest
pusty.
Utylizacja
Utylizacja opakowania:
stosować s do lokalnych przepiw, dzki temu
opakowanie będzie mogło zostać ponownie wykorzystane.
Dyrektywa europejska 2012/19/EU dotycząca
odpadów urządzeń elektrycznych i elektronicznych
przewiduje, że elektryczne urządzenia gospodarstwa
domowego nie powinny być utylizowane w normalnym
ciągu utylizacji stałych odpadów miejskich. Stare
urządzenia powinny być zbierane oddzielnie, aby
zoptymalizować stopień odzysku i recyrkulacji
20
18
PL
Opis pralki
Panel sterowania
Przycisk
TEMPERATURA
POKRĘTŁO
PROGRAMÓW
Szuadka na środki piorące
Przycisk ON/OFF
Przycisk
WIROWANIE
Przycisk i kontrolka
START/PAUZA
WYŚWIETLACZ
Przycisk
OPÓŹNIENIE
Przyciski i
kontrolki OPCJI
Szuadka na środki piorące: do dozowania środków
piorących i dodatków (patrz “Środki piorące i bielizna”).
Przycisk ON/OFF : nacisnąć krótko przycisk w
celu włączenia lub wyłączenia maszyny. Kontrolka
START/PAUZA, która pulsuje powoli w kolorze
zielonym wskazuje, że maszyna jest włączona. W celu
wyłączenia pralki podczas prania konieczne jest dłuższe
przytrzymanie naciśniętego przycisku, przez około 3
sek.; krótkie lub przypadkowe naciśnięcie nie wystarczy
do wyłączenia maszyny. Wyłączenie maszyny podczas
trwającego prania anuluje program prania.
POKRĘTŁO PROGRAMÓW: w celu ustawienia
żądanego programu (patrz “Tabela programów”).
Przyciski i kontrolki OPCJI: służą do wybierania
dostępnych funkcji. Kontrolka wybranej opcji pozostanie
włączona.
Przycisk z kontrolką
OPCJE PRANIA
: nacisnąć w
celu wybrania żądanego stopnia intensywności prania.
Przycisk TEMPERATURA : naciskać w celu
zmniejszenia lub całkowitego wyłączenia temperatury;
ustawiona wartość zostanie wskazana na wyświetlaczu.
Przycisk WIROWANIE : naciskać w celu zmniejszenia
liczby obrotów lub całkowitego wyłączenia wirówki;
ustawiona wartość zostanie wskazana na wyświetlaczu.
Przycisk OPÓŹNIENIE : naciskać w celu ustawienia
opóźnionego startu wybranego programu; opóźnienie
zostanie wskazane na wyświetlaczu.
Przycisk z kontrolką START/PAUZA: kiedy zielona
kontrolka pulsuje powoli, nacisnąć przycisk w celu
uruchomienia prania. Po uruchomieniu cyklu kontrolka
świeci w sposób ciągły. W celu wybrania pauzy w praniu
należy nacisnąć ponownie przycisk, kontrolka zacznie
pulsować w kolorze pomarańczowym. Jeśli symbol
nie świeci się, można otworzyć drzwiczki. W celu
ponownego uruchomienia prania od miejsca, w którym
zostało przerwane, należy ponownie nacisnąć przycisk.
Przycisk
BLOKADA
: w celu uruchomienia lub
wyłączenia blokady panelu sterowania należy
przytrzymać naciśnięty przycisk przez około 2
sekundy. Podświetlony kontrolką wskazuje, że
panel sterowania został zablokowany. W ten sposób
uniemożliwia się dokonywanie przypadkowych zmian w
programach (z wyjątkiem przycisk ON/OFF), zwłaszcza,
jeśli w domu obecne są dzieci.
W celu wyłączenia blokady panelu sterowania należy
przytrzymać naciśnięty przycisk przez około 2 sekundy.
Funkcja stand by
Pralka ta, w myśl nowych norm europejskich związanych
z oszczędnością elektryczną, posiada system auto
wyłączenia (stand by), który włącza się po 30 minutach
nie użytkowania. Ponownie lekko wcisnąć przycisk
ON-OFF i poczekać, aż pralka ponownie włączy się.
Uszczelka przeciwdrobnoustrojowa
Uszczelka drzwiczek jest wykonana ze specjalnej
mieszanki, będącej w stanie zagwarantować ochronę
przeciwdrobnoustrojową poprzez redukcję namnażania
bakterii do 99,99%.
Uszczelka drzwiczek zawiera pirytionian cynku,
będącego substancją biobójczą, która redukuje
namnażanie szkodliwych drobnoustrojów (*), takich jak
bakterie i pleśń, mogących powodować powstawanie
plam, nieprzyjemnych zapachów oraz uszkodzeń
urządzenia.
(*) Zgodnie z badaniami przeprowadzonymi przez Uniwersytet
w Perugii na: Staphylococcus aureus, Escherichia coll,
Pseudomonas aeruginosa, Candida albicans, Aspergillus niger,
Penicillium digitatum.
W rzadkich przypadkach przedłużający się kontakt z uszczelką może
spowodować reakcję alergiczną skóry.
Przycisk
BLOKADA
Przycisk i kontrolka
OPCJE PRANIA
19
PL
Wyświetlacz
Wyświetlacz pomaga zaprogramować urządzenie i dostarcza wielu informacji.
Wyświetlony zostaje czas trwania dostępnych programów, a po uruchomieniu cyklu czas pozostały do jego zakończenia
(na wyświetlaczu zostanie wyświetlony maksymalny czas trwania wybranego cyklu, który może ulec skróceniu po kilku
minutach, ponieważ rzeczywisty czas trwania cyklu zależy od wsadu i wprowadzonych ustawień); natomiast jeśli została
ustawiona funkcja OPÓŹNIENIE, wyświetla się czas pozostający do momentu rozpoczęcia wybranego programu.
Ponadto, po naciśnięciu odpowiednich przycisków wyświetlają się maksymalne wartości szybkości wirowania i
temperatury dla ustawionego programu lub ostatnie zaprogramowane wartości, jeśli są one odpowiednie dla wybranego
programu.
Kontrolka BLOKADY DRZWICZEK
Jeśli symbol się świeci, oznacza to, że drzwiczki są zablokowane. Aby uniknąć uszkodzenia pralki, przed przystąpieniem
do otwierania drzwiczek należy odczekać, aż symbol ten zgaśnie. Aby otworzyć drzwiczki w trakcie trwania cyklu, należy
nacisnąć przycisk START/PAUZA; kiedy symbol BLOKADY DRZWICZEK zgaśnie, można otworzyć drzwiczki.
20
PL
Jak wykonać cykl prania
1. WŁĄCZENIE MASZYNY. Nacisnąć przycisk ,
kontrolka START/PAUZA zacznie powoli pulsować w
kolorze zielonym.
2. ZAŁADOWAĆ BIELIZNĘ. Otworzyć drzwiczki.
Włożyć bieliznę, uważając, aby nie przekroczyć
wielkości wsadu wskazanej w tabeli programów
znajdującej się na następnej stronie.
3. WSYPAĆ ŚRODEK PIORĄCY. Wysunąć szuadkę
i umieścić środek piorący w odpowiednich komorach
zgodnie ze wskazówkami zawartymi w rozdziale
Środki piorące i bielizna”.
4. ZAMKNĄĆ DRZWICZKI.
5. WYBRAĆ PROGRAM. Przy pomocy pokrętła
PROGRAMY wybrać żądany program; ma on
wstępnie ustawioną temperaturę i prędkość
wirowania, jednak wartości te można zmienić. Na
wyświetlaczu pojawi się czas trwania cyklu.
6. SPERSONALIZOWAĆ CYKL PRANIA. Naciskać
odpowiednie przyciski:
Zmienić temperaturę i/lub prędkość wirowania.
Urządzenie automatycznie wyświetla maksymalne
wartości temperatury i prędkości wirowania dla
ustawionego programu lub ostatnie wybrane wartości,
jeśli są one zgodne z ustawionym programem.
Naciskając przycisk stopniowo zmniejsza się
temperaturę, aż do prania na zimno “OFF”. Naciskając
przycisk stopniowo zmniejsza się prędkość
wirowania, aż do jego wyłączenia “OFF”. Dodatkowe
naciśnięcie przycisków przywróci maksymalne
dostępne wartości.
! Wyjątek: wybierając program 3 temperaturę można
podnieść aż do 90°.
! Wyjątek: wybierając program 4 temperaturę można
podnieść aż do 60°.
Ustawić start z opóźnieniem.
W celu ustawienia opóźnionego rozpoczęcia
wybranego programu należy naciskać odpowiedni
przycisk aż do osiągnięcia żądanego czasu
opóźnienia. Kiedy ta opcja jest aktywna, na
wyświetlaczu zaświeca się symbol . Aby anulować
opóźnienie startu, należy naciskać przycisk do
momentu pojawienia się na wyświetlaczu napisu
“OFF”.
Ustawić żądany stopień intensywności prania.
Opcja umożliwia optymalizację prania w
zależności od stopnia zabrudzenia tkanin oraz
żądanej intensywności prania.
W przypadku silnie zabrudzonej odzieży, należy
nacisnąć przycisk aż do przejścia do poziomu
Intensive”. Poziom ten gwarantuje wysokiej
jakości pranie, dzięki użyciu większej ilości wody w
początkowej fazie cyklu i intensywniejszym ruchom
mechanicznym służy do usuwania najoporniejszych
plam. Może być używany z wybielaczem i bez niego.
Jeśli chce się przeprowadzić wybielanie, należy
włożyć dodatkową szuadkę 3, znajdującą się w
wyposażeniu. Nie przekraczać poziomu „max”
wybielacza w płynie, podanej na środkowym
wskaźniku (zobacz rysunek na str. 22).
W przypadku lekko zabrudzonej odzieży lub w celu
delikatnego obchodzenia się z tkaninami, należy
nacisnąć przycisk aż do przejścia do poziomu
Delicate”. Cykl zredukuje ruchy mechaniczne, aby
zagwarantować doskonały efekt prania delikatnej
odzieży.
Zmiana charakterystyki cyklu.
Naciskać przycisk w celu włączenia opcji; zaświeci
się kontrolka odpowiadająca przyciskowi.
Ponownie nacisnąć przycisk w celu wyłączenia
opcji; kontrolka zgaśnie.
! Jeśli wybrana opcja jest niezgodna z ustawionym
programem, kontrolka będzie pulsować i opcja nie
zostanie włączona.
! W zależności od opcji może się zmieniać zalecana
objętość wsadu i/lub czas trwania cyklu.
7. URUCHOMIĆ PROGRAM. Nacisnąć przycisk START/
PAUZA. Odpowiednia kontrolka zaświeci się kolorem
zielonym i drzwiczki zostaną zablokowane (włączy się
symbol BLOKADY DRZWICZEK ). W celu zmiany
programu w czasie trwania cyklu należy ustawić
pralkę w trybie pauzy, naciskając przycisk START/
PAUZA (kontrolka START/PAUZA zacznie powoli
pulsować bursztynowym światłem); następnie wybrać
żądany cykl i ponownie nacisnąć przycisk START/
PAUZA. W celu otwarcia drzwiczek w trakcie trwania
cyklu należy nacisnąć przycisk START/PAUZA; kiedy
symbol BLOKADY DRZWICZEK zgaśnie, można
otworzyć drzwiczki. Nacisnąć ponownie przycisk
START/PAUZA, aby uruchomić program od momentu,
w którym został on przerwany.
8. KONIEC PROGRAMU. Wskazywany jest przez
napis “END” na wyświetlaczu, kiedy symbol BLOKADY
DRZWICZEK zgaśnie, można otworzyć drzwiczki.
Otworzyć drzwiczki, wyjąć bieliznę i wyłączyć
urządzenie.
! Aby anulować już rozpoczęty cykl, należy długo
przytrzymać wciśnięty przycisk . Cykl zostanie
przerwany i urządzenie wyłączy się.
1 / 1

HOTPOINT/ARISTON RSSF 603 EU Guida utente

Categoria
Lavatrici
Tipo
Guida utente

in altre lingue