Yamaha SYSTEM58 Manuale del proprietario

Yamaha
Marca
Yamaha
Modello
SYSTEM58
Categoria
Accessori per chitarra
Tipo
Manuale del proprietario

Questo manuale è adatto anche per

PRECAUTIONS
The output jack is an EIAJ-standard 1/4" phone jack. Be sure to use
an appropriate connection cable.
The built-in preamplifier is automatically turned on when a plug is
inserted into the output jack. When not using the instrument, or when
playing it without amplification, be sure to remove the plug from the
output jack so that the preamplifier power is turned off.
Always set the VOLUME control to “0” when plugging in or
unplugging the connection cable.
The battery check indicator (BATT.) will light briefly when a plug is
inserted or removed from the output jack. This is normal and does not
indicate a malfunction.
Be sure to remove the battery if the instrument will not be used for an
extended period of time in order to prevent possible damage due to
battery leakage.
Owner’s Manual
Thank you for choosing a Yamaha electric-acoustic guitar.
In order to make the most of the advanced features and
performance provided by your guitar, please read this
manual carefully before using the instrument.
BATTERY REPLACEMENT
Be sure to replace the battery as soon as possible when the battery check
indicator lights in order to avoid reduced sound quality.
*Be sure to remove the battery if the instrument will not be used for an
extended period of time in order to prevent possible damage due to battery
leakage.
q Press the catch on the battery holder in the direction indicated by the arrow
in the illustration in order to unlock it.
w Slide out the battery case.
e Remove the old battery from the battery case, and insert the new battery
making sure that the (+) and (–) terminals of the battery are positioned as
shown in the illustration. Use only a DC9V, S-006P (6F22) or equivalent
battery.
r Slide the battery case back into the battery holder and press firmly so
that the battery case locks into place.
ELECTRIC
ACOUSTIC GUITAR
Battery Holder
Control Section
Bar Sensor
NOMENCLATURE
Output Jack (with power switch function)
SPECIFICATIONS
System SYSTEM-58: Monaural 1 way
Pickup Bar Sensor (Piezo type)
Pre-amplifier Controls
VOL., 3 Band (HIGH, MID, LOW) EQ
control, AMF control
Output jack Combination end pin/power switch
Output impedance 1 kΩ
Power supply 9V DC, S-006P (6F22) dry cell battery
Battery life Approx. 300 hours
* When using a manganese battery.
* Varies according to operating conditions.
Accessories •
Hexagonal wrench for neck adjustment x1
• S-006P (6F22) dry cell battery x1
THE CONTROLS
q VOL. (Volume) Control
Adjusts the overall output volume level.
*Make sure that the VOL. is turned to “0” before connecting or
disconnecting.
w BATT. (Battery Check) Indicator
This indicator will light when the battery needs to be replaced.
Please replace the battery as soon as possible when the BATT. indicator
lights.
e 3 Band Equalizer
LOW : Boosts or cuts the level of the low frequencies.
MID :Boosts or cuts the level of the middle frequencies.
The AMF control r adjusts the center frequency of the band
affected by this control.
HIGH : Boosts or cuts the level of the high frequencies.
r AMF Control
Sets the center frequency of the band of frequencies affected by the MID
equalizer control. The range is from 80 Hz to 10 kHz.
* This control has no effect when the MID equalizer control is set to its center
(“0”) position.
O
P
E
N
Catch
DC9V S-006P
(6F22)
Battery case
q
O
P
E
N
w, re
w
r
q
e
w
r
08.7.7, 1:48 PMPage 2
FCC INFORMATION (U.S.A.)
regulations does not guarantee that interference will not oc-
cur in all installations. If this product is found to be the source
of interference, which can be determined by turning the unit
“OFF” and “ON”, please try to eliminate the problem by using
one of the following measures:
Relocate either this product or the device that is being af-
fected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line fi lter/s.
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory re-
sults, please contact the local retailer authorized to distribute
this type of product. If you can not locate the appropriate
retailer, please contact Yamaha Corporation of America,
Electronic Service Division, 6600 Orangethorpe Ave, Buena
Park, CA90620
The above statements apply ONLY to those products distrib-
uted by Yamaha Corporation of America or its subsidiaries.
This device complies with part 15 of the
FCC Rules.
Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device
must accept any interference received,
including interference that may cause
undesired operation.
CANADA
This Class B digital apparatus complies
with Canadian ICES-003.
Cet appareil numéique de la classe B
est conforme à la norme NMB-003 du
Canada.
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions
contained in this manual, meets FCC requirements. Modi-
fi cations not expressly approved by Yamaha may void your
authority, granted by the FCC, to use the product.
2. IMPORTANT:
When connecting this product to accesso-
ries and/or another product use only high quality shielded
cables. Cable/s supplied with this product MUST be used.
Follow all installation instructions. Failure to follow instruc-
tions could void your FCC authorization to use this product
in the USA.
3. NOTE:
This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15
for Class “B” digital devices. Compliance with these require-
ments provides a reasonable level of assurance that your
use of this product in a residential environment will not
result in harmful interference with other electronic devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions found
in the users manual, may cause interference harmful to the
operation of other electronic devices. Compliance with FCC
Caution!
Внимание!
¡Precaución!
Attenzione!
Vorsicht!
Attention !
Regarding the AG-Stomp Guitar
Power Supply Function
Относительно функции источника питания гитарного процес-
сора AG-Stomp (процессор эффектов для акустических гитар)
Acerca de la función de
alimentación del AG-Stomp
Funzione di alimentazione della
chitarra AG-Stomp
Wichtiger Hinweis zur AG-Stomp-
Stromversorgung für Gitarren
À propos de la fonction d’alimentation
électrique de la guitare du AG-Stomp
This guitar is not compatible with the power supply function on the AG-Stomp
acoustic guitar preamplifier. Using the guitar power supply function on the AG-
Stomp can damage the guitar’s built-in preamplifi er resulting in abnormal sound
output, tuner operation, etc.
* Before connecting the guitar to the AG-Stomp, make sure that the AG-Stomp’s guitar power
supply function is switched OFF (switch OFF the +9V SUPPLY switch) and insert a battery
into the guitar’s battery holder.
Данная гитара несовместима с функцией источника питания на акустическом гитарном
предусилителе процессора AG-Stomp. Использование функции источника питания гитары на
процессоре AG-Stomp может повредить встроенный предусилитель гитары и привести к не-
нормальному выводу звукового сигнала, нарушению работы тюнера, и т.п.
* Перед подсоединением гитары к процессору AG-Stomp убедитесь в том, что функция источника
питания гитарного процессора AG-Stomp выключена (переключатель ВЫКЛ установлен в поло-
жение +9V SUPPLY), а затем вставьте батарею в держатель батареи гитары.
Esta guitarra no es compatible con la función de alimentación del preamplifi cador
para guitarra acústica AG-Stomp. El empleo de la función de alimentación de gui-
tarra del AG-Stomp puede causar daños en el preamplifi cador para guitarra incor-
porado y producir anormalidades en la salida de sonido, operación del afi nador, etc.
* Antes de conectar la guitarra al AG-Stomp, asegúrese de que la función de alimentación de
guitarra del AG-Stomp esté desactivada (OFF) (desconecte (OFF) el interruptor +9V SUP-
PLY) e inserte una pila en el compartimiento de la pila de la guitarra.
Questa chitarra non è compatibile con la funzione di alimentazione del preamplifi ca-
tore per chitarra acustica YAMAHA AG-Stomp. Usando la funzione di alimentazione
della chitarra AG-Stomp si può danneggiare il preamplificatore incorporato della
chitarra, producendo suoni ed un funzionamento dell’accordatore anormali, ecc.
* Prima di collegare la chitarra all’AG-Stomp, controllare che la funzione di alimentazione della
chitarra AG-Stomp sia spenta (portando su OFF l’interruttore +9V SUPPLY) ed inserire una
batteria nel vano batteria della chitarra.
Diese Gitarre ist nicht mit der Stromversorgungsfunktion des Akustik-Gitarren-
Vorverstärkers AG-Stomp kompatibel. Bei Anschluss an die Stromversorgung
des AG-Stomp kann der interne Vorverstärker der Gitarre Schaden nehmen, was
anormalen Klang und Störungen der Stimmgerätfunktion zur Folge hat.
* Bevor Sie die Gitarre anschließen, schalten Sie den AG-Stomp aus (+9V SUPPLY-Schalter auf
„OFF“) und legen eine Batterie in den Batteriehalter der Gitarre ein.
La guitare n’est pas compatible avec la fonction d’alimentation électrique du
préamplifi cateur de guitare acoustique AG-Stomp. L’utilisation de cette fonction sur
l’AG-Stomp peut endommager le préamplifi cateur intégré de la guitare, ce qui nuit
à la qualité du son, au fonctionnement de l‘accordeur, etc.
* Avant de raccorder la guitare à l’AG-Stomp, assurez-vous que la fonction d‘alimentation élec-
trique de guitare de l‘AG-Stomp est désactivée (commutateur +9V SUPPLY en position OFF)
et introduisez une pile dans le porte-pile de la guitare.
  • Page 1 1
  • Page 2 2

Yamaha SYSTEM58 Manuale del proprietario

Yamaha
Marca
Yamaha
Modello
SYSTEM58
Categoria
Accessori per chitarra
Tipo
Manuale del proprietario
Questo manuale è adatto anche per
Scarica il pdf
rapporto

in altre lingue

Documenti correlati