Model PRS
www.dell.com
support.dell.com
Dell
Latitude
L400 Advanced Port Replicator
USER’S GUIDE
4C796A00fc.fm Page 3 Friday, December 15, 2000 2:59 PM
4C796A00fc.fm Page 4 Friday, December 15, 2000 2:59 PM
!
Throughout this guide, blocks of text may be accompanied by an icon and printed in
bold type or in italic type. These blocks are notes, notices, and cautions, and they are
used as follows:
NOTE: A NOTE indicates important information that helps you make better use of
your computer system.
Information in this document is subject to change without notice.
©
1999–2001 Dell Computer Corporation. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Computer Corpo-
ration is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo, Latitude, and DellWare are trademarks of Dell
Computer Corporation.
Other trademarks and trade names may be used in this document to refer to either the entities
claiming the marks and names or their products. Dell disclaims any proprietary interest in trade-
marks and trade names other than its own.
December 2000 P/N 4C796 Rev. A00
!
G:\FrameMaker\DELL\sndmm244\en\4C796A00en.fm
support.dell.com
Dell Latitude L400 Advanced Port Replicator User’s Guide 1-1
The Dell Latitude L400 Advanced Port Replicator (APR) integrates your Dell Latitude
L400 computer quickly and easily into a desktop environment. Use the instructions in
this document to attach external devices to the APR and to connect your computer to
the APR.
Use the following safety guidelines to help protect your APR from potential damage
and to help ensure your own personal safety:
• Do not attempt to service the APR yourself. Always follow installation instruc-
tions closely.
• Be sure that nothing rests on your AC adapter’s power cable and that the cable is
not located where it can be tripped over or stepped on.
• Place the AC adapter in a ventilated area, such as a desk top or on the floor, when
powering the APR. Do not cover the AC adapter with papers or other items that
will reduce cooling. Do not use the AC adapter inside a carrying case.
• Do not use your APR in a wet environment, for example, near a bathtub, sink, or
swimming pool or in a wet basement.
• Do not push objects into air vents or openings of your APR. Doing so can cause
fire or electric shock by shorting out interior components.
• Use only the AC adapter that is approved for use with this APR as indicated in
this document. Use of another type of AC adapter may risk fire or explosion.
• Before you connect the APR to a power source, ensure that the voltage rating of
the AC adapter matches that of the available power source:
— 115 volts (V)/60 hertz (Hz) in most of North and South America and some Far
Eastern countries such as South Korea and Taiwan
— 100 V/50 Hz in eastern Japan and 100 V/60 Hz in western Japan
— 230 V/50 Hz in most of Europe, the Middle East and the Far East
1-2 Dell Latitude L400 Advanced Port Replicator User’s Guide
G:\FrameMaker\DELL\sndmm244\en\4C796A00e
G:\FrameMaker\DELL\sndmm244\en\4C796A00en.fm
• To help prevent electric shock, plug the AC adapter and peripheral power cables
into properly grounded power sources. These cables are equipped with
three-prong plugs to help ensure proper grounding. Do not use adapter plugs or
remove the grounding prong from a cable. If you must use an extension cable,
use a three-wire cable with properly grounded plugs.
• If you use an extension cable with your AC adapter, ensure that the total ampere
rating of the products plugged into the extension cable does not exceed the
ampere rating of the extension cable.
• To remove power from the APR, turn off the computer and disconnect the AC
adapter from the electrical outlet.
• If your computer includes an integrated or optional (PC Card) modem, the cable
used with the modem should be manufactured with a minimum wire size of 26
American wire gauge (AWG) and an FCC-compliant RJ-11 modular plug.
• Disconnect the modem cable during an electrical storm to avoid the remote risk
of electric shock from lightning via the telephone line.
• To help avoid the potential hazard of electric shock, do not connect or disconnect
any cables or perform maintenance or reconfiguration of this product during an
electrical storm.
• When setting up the APR for work, place it on a level surface.
• Protect your APR from environmental hazards such as dirt, dust, food, liquids,
temperature extremes, and overexposure to sunlight.
• When you move your APR between environments with very different tempera-
ture or humidity ranges, condensation may form on or within the computer. To
avoid damaging the APR, allow sufficient time for the moisture to evaporate
before using the computer.
!
!"#
$
• When you disconnect a cable, pull on its connector or on its strain-relief loop, not
on the cable itself. As you pull out the connector, keep it evenly aligned to avoid
bending any connector pins. Also, before you connect a cable make sure both
connectors are correctly oriented and aligned.
• Handle the APR with care.
• Before you clean your APR, shut down the computer and disconnect it from the
APR. Then unplug the APR from its power source.
• Clean your APR with a soft cloth dampened with water rather than with liquid or
aerosol cleaners.
support.dell.com
Dell Latitude L400 Advanced Port Replicator User’s Guide 1-3
G:\FrameMaker\DELL\sndmm244\en\4C796A00en.fm
• If your APR or computer gets wet or is damaged, follow the procedures
described in “Troubleshooting Your Computer,” in the
User’s Guide
. If, after fol-
lowing these procedures, you confirm that your APR or computer is not operating
properly, contact Dell. (See “Getting Help,” in the
User’s Guide
for the appropri-
ate telephone number.)
The input/output (I/O) connectors on the back of the APR duplicate the primary con-
nectors on the back and side of your computer. Table 1-1 shows the icons for each of
the connectors on the back of the APR and indicates the type of external device(s)
that can be attached to each connector.
The AC adapter that came with the APR connects to the
AC adapter connector.
A serial device, such as a serial mouse, connects to the
serial connector.
A microphone connects to the microphone connector.
A speaker or headphones connect to the line-out
connector.
A network interface cable connects to the NIC connector.
A USB device, such as a USB mouse, connects to the
USB connector.
An external phone line connects to the modem connector.
An external monitor connects to the monitor connector.
A parallel device, such as a printer, connects to the parallel
connector.
An external Personal System/2 (PS/2)-compatible mouse
connects to the PS/2 mouse connector.
An external PS/2-compatible keyboard or external numeric
keypad connects to the PS/2 keyboard connector.
An external CD-ROM, DVD-ROM, CD-RW, Zip 250, or dis-
kette drive connects to the external media bay connector.
1-4 Dell Latitude L400 Advanced Port Replicator User’s Guide
G:\FrameMaker\DELL\sndmm244\en\4C796A00e
G:\FrameMaker\DELL\sndmm244\en\4C796A00en.fm
Use the following instructions to attach external devices to the APR.
%&' #
!( !#)$*+
# "!+ +!
$
1. Refer to Figure 1-1 to attach external devices to the appropriate connectors on the
back of the APR.
NOTES: If the cable connector from the external device has thumbscrews, be
sure to tighten them to ensure a proper connection.
To connect the computer to a small computer system interface (SCSI) device, you
must attach a SCSI PC Card to your computer. See “PC Cards” in your online Dell
Latitude L400 User’s Guide for information about using PC Cards.
,$
For detailed information on using external devices with your computer, see
“Using External Devices” in your online User’s Guide.
2. Connect the external devices to their power sources, if applicable.
PS/2 mouse connector keyboard connector
USB connector
serial connector
parallel connector
monitor connector
network connector
microphone connector
AC adapter connector
headphone/speakers connector
modem connector
external media bay
support.dell.com
Dell Latitude L400 Advanced Port Replicator User’s Guide 1-5
G:\FrameMaker\DELL\sndmm244\en\4C796A00en.fm
Use the following instructions to connect your computer to the APR.
1. Save all your work, and exit all application programs.
2. Shut down the computer.
3. If you have not already done so, connect the AC adapter to the connector on the
APR (see Figure 1-1), and plug the AC power cable into an AC power source.
4. Place the back of the computer over the APR platform, aligning the sides of the
computer between the platform wings (see Figure 1-2).
5. Carefully lower the computer onto the APR platform, as shown in Figure 1-2, until
the APR and computer docking connectors engage.
When you feel or hear a click, the computer is latched to the APR and the docking
connectors are fully engaged.
-!
+" +
#+ +
$
6. Turn on the computer.
APR docking
connector
platform wings
APR platform
1-6 Dell Latitude L400 Advanced Port Replicator User’s Guide
G:\FrameMaker\DELL\sndmm244\en\4C796A00e
G:\FrameMaker\DELL\sndmm244\en\4C796A00en.fm
Use the following procedure to disconnect the computer from the APR:
1. Save all your work, and exit all application programs.
2. Shut down the computer.
3. At the same time, press down on the left and right release buttons on the top of
the replicator, as shown in Figure 1-3, to undock the computer.
4. Lift the computer up and away from the APR.
release buttons
support.dell.com
Dell Latitude L400 Advanced Port Replicator User’s Guide 1-7
G:\FrameMaker\DELL\sndmm244\en\4C796A00en.fm
The security lock prevents unauthorized removal of your APR. The security lock
swings out of the APR, as shown in Figure 1-4. An antitheft cable device is looped
around an immovable object, passed through the security lock on the APR, and then
locked to the security cable slot on the computer. For more information see the
Dell
Latitude L400 User’s Guide
.
!"#$%
security lock
1-8 Dell Latitude L400 Advanced Port Replicator User’s Guide
G:\FrameMaker\DELL\sndmm244\en\4C796A00e
G:\FrameMaker\DELL\sndmm244\en\4C796A00en.fm
Table 1-2 lists the technical specifications for the APR.
"&
Height . . . . . . . . . . . . . . . . . . . . . . . . . . . 38.25 mm (1.5 inches)
Depth. . . . . . . . . . . . . . . . . . . . . . . . . . . . 50.0 mm (2.0 inches)
Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298.0 mm (11.7 inches)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . 389 g (0.86 lb)
Expansion (to connect to computer) . . . . APR docking connector
Serial (DTE) . . . . . . . . . . . . . . . . . . . . . . . 9-pin male connector
Parallel . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-hole female connector
PS/2-compatible keyboard/keypad. . . . . . 6-hole external keyboard connector
PS/2-compatible mouse. . . . . . . . . . . . . . 6-hole external mouse connector
LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RJ45 connector
Modem . . . . . . . . . . . . . . . . . . . . . . . . . . RJ11 connector
Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . 15-hole female connector
Audio jacks. . . . . . . . . . . . . . . . . . . . . . . . microphone-in, one line-out audio
USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-pin connectors
External media bay . . . . . . . . . . . . . . . . . 68-pin IDE/FDD connector
DC in . . . . . . . . . . . . . . . . . . . . . . . . . . . . three-pin DC power connector
Operating temperature . . . . . . . . . . . . . . 5° to 35°C (41° to 95°F)
Storage temperature . . . . . . . . . . . . . . . . –20° to 60°C (–4° to 149°F)
Operating relative humidity . . . . . . . . . . . 20% to 80% (noncondensing)
Storage relative humidity . . . . . . . . . . . . . 8% to 90% (noncondensing)
!
support.dell.com
Dell Latitude L400 Advanced Port Replicator User’s Guide 1-9
G:\FrameMaker\DELL\sndmm244\en\4C796A00en.fm
!
Electromagnetic Interference (EMI) is any signal or emission, radiated in free space or
conducted along power or signal leads, that endangers the functioning of a radio navi-
gation or other safety service or seriously degrades, obstructs, or repeatedly
interrupts a licensed radio communications service. Radio communications services
include but are not limited to AM/FM commercial broadcast, television, cellular ser-
vices, radar, air-traffic control, pager, and Personal Communication Services (PCS).
These licensed services, along with unintentional radiators such as digital devices,
including computer systems, contribute to the electromagnetic environment.
Electromagnetic Compatibility (EMC) is the ability of items of electronic equipment to
function properly together in the electronic environment. While this computer system
has been designed and determined to be compliant with regulatory agency limits for
EMI, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause interference with radio communications services, which
can be determined by turning the equipment off and on, you are encouraged to try to
correct the interference by one or more of the following measures:
• Reorient the receiving antenna.
• Relocate the computer with respect to the receiver.
• Move the computer away from the receiver.
• Plug the computer into a different outlet so that the computer and the receiver
are on different branch circuits.
If necessary, consult a Dell Technical Support representative or an experienced radio/
television technician for additional suggestions. You may find the
FCC Interference
Handbook, 1986
, to be helpful. It is available from the U.S. Government Printing
Office, Washington, DC 20402, Stock No. 004-000-00450-7 or on the World Wide
Web at http://www.fcc.gov/cib/Publications/tvibook.html.
Dell computer systems are designed, tested, and classified for their intended electro-
magnetic environment. These electromagnetic environment classifications generally
refer to the following harmonized definitions:
• Class A is typically for business or industrial environments.
• Class B is typically for residential environments.
Information Technology Equipment (ITE), including peripherals, expansion cards, print-
ers, input/output (I/O) devices, monitors, and so on, that are integrated into or
connected to thesystem should match the electromagnetic environment classification
of the computer system.
#%%# . + #
+,! #+
! $. #
+/
!$0 "# !#,$
+"+#,#
&&$$& &&-$$
1-10 Dell Latitude L400 Advanced Port Replicator User’s Guide
G:\FrameMaker\DELL\sndmm244\en\4C796A00e
G:\FrameMaker\DELL\sndmm244\en\4C796A00en.fm
Most Dell computer systems are classified for Class B environments. To determine
the electromagnetic classification for your system or device, refer to the following
sections specific for each regulatory agency. Each section provides country-specific
EMC/EMI or product safety information.
Most Dell computer systems are classified by the Federal Communications Commis-
sion (FCC) as Class B digital devices. However, the inclusion of certain options can
change the rating of some configurations to Class A. To determine which classification
applies to your computer system, examine all FCC registration labels located on the
bottom or back panel of your computer, on card-mounting brackets, and on the cards
themselves. If any one of the labels carries a Class A rating, your entire system is con-
sidered to be a Class A digital device. If
all
labels carry an FCC Class B rating as
distinguished by either an FCC ID number or the FCC logo, ( ), your system is con-
sidered to be a Class B digital device.
Once you have determined your system’s FCC classification, read the appropriate
FCC notice. Note that FCC regulations provide that changes or modifications not
expressly approved by Dell could void your authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the follow-
ing two conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A dig-
ital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the manufacturer’s
instruction manual, may cause harmful interference with radio communications. Oper-
ation of this equipment in a residential area is likely to cause harmful interference, in
which case you will be required to correct the interference at your own expense.
This equipment has been tested and found to comply with the limits for a Class B dig-
ital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instruction manual, may
cause interference with radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, you are encouraged to try to correct the interfer-
ence by one or more of the following measures:
support.dell.com
Dell Latitude L400 Advanced Port Replicator User’s Guide 1-11
G:\FrameMaker\DELL\sndmm244\en\4C796A00en.fm
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.
The following information is provided on the device or devices covered in this docu-
ment in compliance with FCC regulations:
• Model number: PRS
• Company name: Dell Computer Corporation
EMC Engineering Department
One Dell Way
Round Rock, Texas 78682 USA
512-338-4400
This equipment complies with Part 68 of the FCC rules. On the bottom of your com-
puter is a label that contains, among other information, the FCC registration number
and ringer equivalence number (REN) for your equipment. If requested, you must pro-
vide this information to the telephone company.
The REN is used to determine the quantity of devices that may be connected to the
telephone line. Excessive RENs on the telephone line may result in the devices not
ringing in response to an incoming call. In most areas, the sum of all the RENs on your
telephone line should be less than five to ensure proper service from the telephone
company. To be certain of the number of devices that you may connect to a line, as
determined by the total RENs, contact your local telephone company.
The registration jack Universal Service Order Code (USOC) used by this equipment is
RJ-11C. An FCC compliant telephone cord and modular plug is provided with this
equipment. This equipment is designed to be connected to the telephone network or
premises wiring using a compatible modular jack that is Part 68 compliant.
This equipment cannot be used on public coin-phone service provided by the tele-
phone company. Connection to party line service is subject to state tariffs.
There are no user serviceable parts on the modem contained in your computer.
If your telephone equipment causes harm to the telephone network, the telephone
company will notify you in advance that service may be temporarily discontinued. If
advance notice is not practical, the telephone company will notify you as soon as pos-
sible. Also, you will be advised of your right to file a complaint with the FCC if you
believe it is necessary.
1-12 Dell Latitude L400 Advanced Port Replicator User’s Guide
G:\FrameMaker\DELL\sndmm244\en\4C796A00e
G:\FrameMaker\DELL\sndmm244\en\4C796A00en.fm
The telephone company may make changes in its facilities, equipment, operations, or
procedures that could affect the operation of this equipment. If this happens, the tele-
phone company will provide advance notice in order for you to make necessary
modifications to maintain uninterrupted service.
If you experience trouble with this telephone equipment, refer to the chapter titled
"Getting Help" in your system's troubleshooting documentation or, for some systems,
the section titled "Contacting Dell" in your system's online guide to find the appropri-
ate telephone number for obtaining customer assistance. If the equipment is causing
harm to the telephone network, the telephone company may request that you discon-
nect the equipment until the problem is resolved.
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to
use a computer or other electronic device, including fax machines, to send any mes-
sage unless such message clearly contains in a margin at the top or bottom of each
transmitted page or on the first page of the transmission, the date and time it is sent,
identification of the business, other entity, or individual sending the message, and the
telephone number of the sending machine or such business, other entity, or individ-
ual. The telephone number provided may not be a 900 number or any other number
for which charges exceed local or long-distance transmission charges.
Most Dell computers (and other Dell digital apparatus) are classified by the Industry
Canada (IC) Interference-Causing Equipment Standard #3 (ICES-003) as Class B digital
devices. To determine which classification (Class A or B) applies to your computer (or
other Dell digital apparatus), examine all registration labels located on the bottom or
the back panel of your computer (or other digital apparatus). A statement in the form
of “IC Class A ICES-003” or “IC Class B ICES-003” will be located on one of these
labels. Note that Industry Canada regulations provide that changes or modifications
not expressly approved by Dell could void your authority to operate this equipment.
The IC label identifies certified equipment. This certification means that the equip-
ment meets telecommunications network protective, operational, and safety
requirements as prescribed in the appropriate Terminal Equipment Technical Require-
ments document(s). The IC label does not guarantee that the equipment will operate
to the user's satisfaction.
This Class B (or Class A, if so indicated on the registration label) digital apparatus
meets the requirements of the Canadian Interference-Causing Equipment
Regulations.
Cet appareil numérique de la Classe B (ou Classe A, si ainsi indiqué sur l’étiquette
d’enregistration) respecte toutes les exigences du Reglement sur le Materiel
Brouilleur du Canada.
support.dell.com
Dell Latitude L400 Advanced Port Replicator User’s Guide 1-13
G:\FrameMaker\DELL\sndmm244\en\4C796A00en.fm
Before installing this equipment, users should ensure that it is permissible to be con-
nected to the facilities of the local telecommunications company. The equipment
must also be installed using an acceptable method of connection. The customer
should be aware that compliance with the above conditions may not prevent degrada-
tion of service in some situations.
Repairs to certified equipment should be coordinated by a representative designated
by the supplier. Any repairs or alteration made by a user to this equipment, or equip-
ment malfunctions, may give the telephone communications company cause to
request the user to disconnect the equipment.
Users should ensure for their own protection, that the electrical ground connections
of the power utility, telephone lines, and internal metallic water-pipe system, if
present, are connected together. This precaution may be particularly important in rural
areas.
. ! $
+""
$
NOTE: The REN assigned to each terminal device provides an indication of the maxi-
mum number of terminals allowed to be connected to a telephone interface. The
termination on an interface may consist of any combination of devices subject only to
the requirement that the sum of the RENs of all the devices does not exceed the
number five.
The REN for the internal modem as stated on the IC regulatory label located on the
bottom of the computer is 0.6B.
The following information is provided in compliance with IC regulations:
Dell Computer Corporation
Warranty and Repair Service Center
One Dell Way
Round Rock, TX 78682 USA
512-338-4400
Marking by the symbol indicates compliance of this Dell system to the EMC
Directive and the Low Voltage Directive of the European Union. Such marking is indic-
ative that this Dell system meets the following technical standards:
• EN 55022 — “Limits and Methods of Measurement of Radio Interference Char-
acteristics of Information Technology Equipment.”
• EN 50082-1: 1992 — “Electromagnetic compatibility—Generic immunity stan-
dard Part 1: Residential, commercial, and light industry.”
• EN 60950 — “Safety of Information Technology Equipment.”
1-14 Dell Latitude L400 Advanced Port Replicator User’s Guide
G:\FrameMaker\DELL\sndmm244\en\4C796A00e
G:\FrameMaker\DELL\sndmm244\en\4C796A00en.fm
NOTE: EN 55022 emissions requirements provide for two classifications:
•
Class A is for typical commercial areas.
•
Class B is for typical domestic areas.
This Dell device is classified for use in a typical Class B domestic environment.
A “Declaration of Conformity” in accordance with the preceding directives and stan-
dards has been made and is on file at Dell Computer Corporation Products Europe BV,
Limerick, Ireland.
!"
#$
Most Dell computer systems are classified by the Voluntary Control Council for Inter-
ference (VCCI) as Class B Information Technology Equipment (ITE). However, the
inclusion of certain options can change the rating of some configurations to Class A.
ITE, including peripherals, expansion cards, printers, input/output (I/O) devices, moni-
tors, and so on, integrated into or connected to the system, should match the
electromagnetic environment classification (Class A or B) of the computer system.
To determine which classification applies to your computer system, examine the regu-
latory labels/markings (see Figures 1-5 and 1-6) located on the bottom or back panel of
your computer. Once you have determined your system’s VCCI classification, read the
appropriate VCCI notice.
This device belongs to Class B devices as described in EN 55022, unless it is spe-
cifically stated that it is a Class A device on the specification label. The following
applies to devices in Class A of EN 55022 (radius of protection up to 30 meters).
The user of the device is obliged to take all steps necessary to remove sources of
interference to telecommunication or other devices.
!"#$$$$
% &# '( ) " *)+
# &,) &$$)#
,##"
(VCCI)
A
support.dell.com
Dell Latitude L400 Advanced Port Replicator User’s Guide 1-15
G:\FrameMaker\DELL\sndmm244\en\4C796A00en.fm
This is a Class A product based on the standard of the Voluntary Control Council for
Interference (VCCI) for information technology equipment. If this equipment is used in
a domestic environment, radio disturbance may arise. When such trouble occurs, the
user may be required to take corrective actions.
'())#*%
This is a Class B product based on the standard of the Voluntary Control Council for
Interference (VCCI) for information technology equipment. If this equipment is used
near a radio or television receiver in a domestic environment, it may cause radio inter-
ference. Install and use the equipment according to the instruction manual.
+(),)#*%
%!"&'
To determine which classification (Class A or B) applies to your computer (or other
Dell digital device), examine the Republic of Korean Ministry of Information and Com-
munications (MIC) registration labels located on your computer (or other Dell digital
device). The MIC label may be located separately from the other regulatory marking
applied to your product. Line three of the label identifies the emissions class for the
product—“(A)” for Class A products or “(B)” for Class B products.
NOTE: MIC emissions requirements provide for two classifications:
•
Class A devices are for business purposes.
•
Class B devices are for nonbusiness purposes.
VCCI-A
1-16 Dell Latitude L400 Advanced Port Replicator User’s Guide
G:\FrameMaker\DELL\sndmm244\en\4C796A00e
G:\FrameMaker\DELL\sndmm244\en\4C796A00en.fm
Please note that this device has been approved for business purposes with regard to
electromagnetic interference. If you find that this device is not suitable for your use,
you may exchange it for a nonbusiness-purpose device.
Please note that this device has been approved for nonbusiness purposes and may be
used in any environment, including residential areas.
( &)*&
The equipment should draw power from a socket with an attached protection circuit (a
three-prong socket). All equipment that works together (computer, monitor, printer,
and so on) should have the same power supply source.
The phasing conductor of the room’s electrical installation should have a reserve
short-circuit protection device in the form of a fuse with a nominal value no larger than
16 amperes (A).
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
Dell Latitude L400 Manuale utente
- Tipo
- Manuale utente
- Questo manuale è adatto anche per
in altre lingue
- English: Dell Latitude L400 User manual