Excell EX-2001NC Racer Manuale utente

EXCELL PRECISION CO., LTD.

The information contained herein is the property of EXCELL PRECISION

CO., LTD and is supplied without liability for errors or omissions. No part

may be reproduced or used except as authorised by contract or other

written permission. The copyright and the foregoing restriction on

reproduction and use extend to all media in which the information may be

embodied.

EX-2001 NC RACER ZSME300000091

1

EXCELL PRECISION CO., LTD.

TABLE OF CONTENTS

SAFETY.......................................................................................................................................3

CLEANNING TIPS.......................................................................................................................4

CHAPTER 1 OPERATION GUIDE ..............................................................................................5

CHARTER 2 SPECIFICATIONS..................................................................................................7

CHAPTER 3 FRONT AND REAR PANEL...................................................................................9

3-1 FRONT PANEL ..................................................................................................................9

3-2

REAR PANEL...................................................................................................................10

CHAPTER 4 INSTALLATION....................................................................................................11

4-1

LOAD CELL.....................................................................................................................11

4-2 INDICATOR INSTALLATION AND DIMENSIONS............................................................11

CHAPTER 5 CAPACITY CALIBRATION ..................................................................................13

5-1 PARAMETER SETTING...................................................................................................13

5-1-1 Flow Diagram...........................................................................................................13

5-1-2 Description...............................................................................................................14

5-2 CALIBRATION SETTING.................................................................................................15

5-2-1 Calibration Procedure.............................................................................................15

5-2-2 Zero Calibration.......................................................................................................15

5-2-3 Weight Calibration...................................................................................................15

5-3 LINEARITY CALIBRATION .............................................................................................16

5-4 PASSWORD SETTING ....................................................................................................19

5-5 ERROR MESSAGES .......................................................................................................20

CHAPTER 6 ANIMAL SCALE FUNCTION SETTING...............................................................21

CHAPTER 7 INTERFACES.......................................................................................................22

7-1 OP-01 RS-422 & RS-485 INTERFACE.............................................................................22

EX-2001 NC RACER ZSME300000091

2

EXCELL PRECISION CO., LTD.

7-2 OP-02 PARALLEL BCD OUTPUT....................................................................................26

7-3 OP-03 ANALOGUE CURRENT / VOLTAGE OUTPUT INTERFACE................................28

7-4 OP-05 PARALLEL PRINTER OUTPUT & RS-232 & CURRENT LOOP...........................29

7-5 OP-06 RS-232 & CURRENT LOOP..................................................................................32

7-6 OP-07 RS-232, CURRENT LOOP & DATA CLOCK OUTPUT..........................................33

7-7 OP-08 CONTROL I /O (2I /4O) INTERFACE.....................................................................34

CHAPTER 8 MAINTENANCE ...................................................................................................38

8-1

RESET ALL PARAMETERS BACK TO DEFAULT...........................................................38

8-2

RESET GENERAL FUNCTION PARAMETERS BACK TO DEFAULT.............................38

8-3 SELF-DIAGNOSIS MODE ...............................................................................................38

8-3-1 7 Digit Display and LED Status Light Diagnosis................................................39

8-3-2 Keyboard and Calibration ON / OFF Switch Diagnosis .....................................39

8-3-3 RS-232 Serial Output / Input Interface Diagnosis ( OP-06 / OP-07 )..................39

8-3-4 BCD Parallel Output Interface Diagnosis ( OP-02 )............................................39

8-3-5 Analogue Current Output Interface Diagnosis ( OP-03 ) ...................................40

8-3-6 Parallel Printer Interface Diagnosis ( OP-05 ).....................................................40

8-3-7 Main Board EEPROM Memory Diagnosis...........................................................40

8-3-8 OP-08 Control I /O (2I /4O) Diagnosis..................................................................40

CHAPTER 9 FUNCTION TABLE...............................................................................................41

APPENDIX: 7-SEGMENT DISPLAY CHARACTERS...............................................................46

EX-2001 NC RACER ZSME300000091

3

EXCELL PRECISION CO., LTD.

SAFETY

 Disconnect the main power supply before opening the indicator housing or disassembling

the indicator.

 In the process of maintenance, please cut off the source if contacting to any electron, socket

and groupware for fear of getting an electric shock、short current and shattering weight

controller or error movement.

 Avoid using the indicator in direct sunlight. The operating ambient temperature range is -10 ~

+40 °C.

 Use 100 V ~ 240 V AC

 When using AC source wiring, the front line “L” should be connected to weight controller “L”.

The neutral line “N” should be connected to weight controller “N”. “ ” of weight controller

should connected to the ground.

 Connect the ground correctly. (Ground impedance < 100 Ω) Avoid connecting the ground

connection with other equipment. The indicator must always be connected to the electrical

ground (earth) for safe operation.

 In the industrial surrounding, the main power supply has non-seasonal and short-lived pulse

(high electric current or high voltage) because of high power instrument (start-up and

closedown of the source). Users take necessary actions by themselves to protect weight

controller and other periphery instrument. (Using isolated transformer or restraining

groupware)

 The weight installation wiring conforms to standard law in the user’s country.

 When installing, keep the indicator away from noise such as high voltage、high current and

high power switches.

 The distances of input wiring、output wiring and power wiring are 30 ~ 50 mm. Try to across

vertically if not being separated and avoid being set parallelly.

 The diameter of I/O and BCD wiring is 12 AWG ~ 24 AWG. Please select the proper diameter

of the wiring materials. (The length ≦ 10 m)

 Set proper resolution for system installation for fear of decreasing the stability and reliability.

 When the temperature range is -10 ~ +40 °C and the resolution is over 1 / 3 000, please

select the weight load cell passing C3.

EX-2001 NC RACER ZSME300000091

4

EXCELL PRECISION CO., LTD.

CLEANNING TIPS

 Please clean the indicator by alcohol

and chemical medicament.

 Clean it with a wet cloth and gentle cleanser

and dry it with a soft cloth.

 Do not swash the indicator.

 Do not breakout and maintain the indicator.

If there is something wrong with the indicator,

please contact your supplier.

 Keep away from high temperature,

damp or direct sunlight conditions.

 Do not shake the indicator fiercely.

EX-2001 NC RACER ZSME300000091

5

EXCELL PRECISION CO., LTD.

CHAPTER 1 OPERATION GUIDE

FUNCTION OPERATION PROCEDURE DESCRIPTION

General function

setting

Press and hold the key,

then press the

Refer to Chapter 9 Functions Table

to set FUNC. 0 ~ FUNC. 7

Capacity parameter

setting

Switch the capacity calibration

switch to “ON”

and then press the

Set the parameter for decimal

point, max. capacity, min. division,

zero tracking, unstable detection

Refer to < 5-1 > Parameter Setting

Calibration

Switch the capacity calibration

switch to “ON”

and then press the

Calibration procedures.

Refer to < 5-2 > Calibration Setting

Self-diagnosis mode

Turn on the indicator,

press and hold and

the indicator starts the self-test

procedure.

Refer to < 8-3 > Self-diagnosis

Mode for details

Reset all parameters

back to default

Switch the calibration switch to

“ON”, turn on the indicator,

press and hold and

while the indicator is in the

self-testing sequence

Refer to < 8-1 > Reset All

Parameter Back to Default

Reset general function

parameter back to

factory standard setting

Turn on the indicator,

press and hold , followed

by pressing

while the indicator is in the

self-testing sequence

Refer to < 8-2 > Reset General

Function Parameter Back to

Default

Display software version

Turn on the indicator,

press and hold the

while the indicator is in the

self-test sequence

The main display section displays

the software version, press any key

to exit

Function parameter

setting

Press and hold ,

followed by pressing

HI, LO, Zero Band parameter

setting

ENTER

F n

C A L

ENTER

GROSS

NET

F n

ENTER

F n

ENTER

C A L

ENTER

C A L

EX-2001 NC RACER ZSME300000091

6

EXCELL PRECISION CO., LTD.

 Operation of Keys in the Setting Mode

⇒ Increase the number of the flashing digit by one

⇒ Decrease the number of the flashing digit by one

⇒ Shift the flashing digit one space to left

⇒ Shift the flashing digit one space to right

⇒ Save the settings

⇒ Exit the settings

ZERO

+

GROSS

NET

PRINT

TARE

—

ENTER

STANDBY

OPERAE

EX-2001 NC RACER ZSME300000091

7

EXCELL PRECISION CO., LTD.

CHARTER 2 SPECIFICATIONS

ANALOGUE

◆ Load cell excitation : DC 5 V ± 5%，120 mA (up to 8 × 350 Ω load cells)

◆ Maximum signal voltage : 20 mV

◆ Input sensitivity : 0.3 μV / D (minimum)

◆ Conversion rate : Approximately 120 times/s (maximum)

◆ Internal Resolution : 19 bits

DIGITAL

◆ Main display : 7 digits, bright red LED, 20 mm, 7-segment

◆ Status display : 6 character display, bright red LED

◆ Display update rate : 50 times/s

◆ Display capacity : -199 999 to 999 999

◆ Min division : 1、2、5、10、20、50

◆ Decimal point : 0、0.0、0.00、0.000、0.0 000

◆ Memory : Calibration parameters and function settings saved in

EEPROM

EX-2001 NC RACER ZSME300000091

8

EXCELL PRECISION CO., LTD.

INTERFACE

◆ OP-01 RS-422 / RS-485

◆ OP-02-1 Parallel BCD output ( TTL )

◆ OP-02-2 Parallel BCD output ( O.C. )

◆ OP-03 Analog output ( 4 ~ 20 mA )

◆ OP-05 Parallel Printer output / RS-232C & CURRENT LOOP

◆ OP-05 Free Form

◆ OP-06 RS-232C & CURRENT LOOP

◆ OP-07 RS-232C & CURRENT LOOP & Data Clock Output

◆ OP-08 Control I / O ( 2I /4O )

POWER SUPPLY INPUT

◆ AC Power : 100 V ~ 240 V

◆ Power consumption: Approximately 10 W

OTHER

◆Operating temperature and humidity range : -10 ~ 40 ℃ ,< 85 % RH

◆Dimension (mm) : 210 ( W ) × 108 ( H ) × 207 ( D )

◆Weight : Approximately 1.7 kg

EX-2001 NC RACER ZSME300000091

9

EXCELL PRECISION CO., LTD.

CHAPTER 3 FRONT AND REAR PANEL

3-1 FRONT PANEL

1

MAIN DISPLAY

• Displays gross weight or net weight

2 STATUS INDICATION LIGHTS

☼ POWER : Power Indication

☼ ZERO : Zero status indication

☼ MOTION : Unstable weighing indication

☼ GROSS : Main display section currently displays gross wt.

☼ NET : Main display section currently displays net wt.

☼ TARE ENTERED : Tare indication

3 KEYS

1) Standby mode ON / OFF

2) When setting the parameter or calibration, it works as quit or exit from setting

1) Sets weight back to zero

2) When setting the parameter or calibration, it cycles from 0 to 9

1) Tare function

2) When setting the parameter or calibration, it cycles from 9 to 0

1) Switches between gross wt. / net wt. on the main display

2) When setting the parameter or calibration,

it shifts the flashing character to the left

1) Manually output serial / parallel data

2) When setting the parameter or calibration, it shifts the flashing character to the right

1) Weight accumulation, sub-total function (for OP-05)

2) Sets capacity parameter

1) Weight accumulation, grand-total function (for OP-05)

2) Capacity calibration

Confirmation key

1

2

3

4

STANDBY

OPERAE

ZERO

+

GROSS

NET

TARE

—

PRINT

ENTER

F n

C A L

POWER ZERO MOTION GROSS NET TARE ENTERED

ON

STANDBY

OPERAE

ZERO

+

TARE

—

GROSS

NET

PRINT

F n

C A L

ENTER

EX-2001 NC RACER ZSME300000091

10

EXCELL PRECISION CO., LTD.

DATA IN / OUT

LOAD CELL

FUSE/0.5A

AC 100V~240V

CONTROL IN / OUTPUT

2 1

C2 C1

4 3 2 1

OUTPUT

INPUT

before opening the covers.

Isolating the ac power

! WARNING

12

3

4

5

4 CAPACITY PARAMETER & CALIBRATION SWITCH

Slide the switch to the left is “ON” and Slide the switch to the right is “OFF”

3-2 REAR PANEL

1. AC power in terminal

2. Fuse 250 V / 0.5 A

3. Load cell connector

4. Optional interface location (if fitted)

5. Control I/O Interface location

EX-2001 NC RACER ZSME300000091

11

EXCELL PRECISION CO., LTD.

6

1

2

8

7

5

4

3

Load cell

Load cell cable

Shield

SEN+

SIG-SIG+

EXC+

EXC-

SEN-

CHAPTER 4 INSTALLATION

4-1 LOAD CELL

Four-wire (five-wire) load cell Six-wire (seven-wire) load cell

Pin 1 & 2 short, connected to EXC+ Pin 1 connected to EXC+

Pin 3 & 4 short, connected to EXC- Pin 2 connected to SEN+

Pin 5 connected to SIG+ Pin 3 connected to EXC-

Pin 6 connected to SIG- Pin 4 connected to SEN-

Pin 7 connected to the Shield Pin 5 connected to SIG+

Pin 6 connected to SIG-

Pin 7 connected to the Shield

4-2 INDICATOR INSTALLATION AND DIMENSIONS

2 The indicator can be installed in a control panel as detailed below

Packing

Panel

Fixed Rail

Load Cell

Load Cell Cable

Shield

1

2

3

4

5

6

7

8

EX-2001 NC RACER ZSME300000091

12

EXCELL PRECISION CO., LTD.

! WARNING

before opening the covers.

Isolating the ac power

LOAD CELL

AC 100V~240V

IN / OUTPUT

2

FUSE/0.5A

CONTROL

INPUT

1 2

OUTPUT

4

C2 C1

3 1

DATA IN / OUT

2 INDICATOR DIMENSIONS (measurement unit: mm)

EX-2001 NC RACER ZSME300000091

13

EXCELL PRECISION CO., LTD.

CHAPTER 5 CAPACITY CALIBRATION

5-1 PARAMETER SETTING

Switch the capacity calibration switch to “ON” and the display shows .

Press the key and the display shows . then enter the setting mode.

5-1-1 Flow Diagram

1.

2.

3.

4.

5.

.

Decimal Point

. .

Setup completed

Max. Capacity

Setup completed

Min. Division

.

Setup completed

Zero Tracking

. . .

Setup completed

Unstable

Detection

.

Switch the

calibration switch

to OFF

Setup completed

DISPLAY

F n

ENTER

STANDBY

OPERAE

ENTER

EX-2001 NC RACER ZSME300000091

14

EXCELL PRECISION CO., LTD.

5-1-2 Description

1) Zero Tracking

Display Division / Time

. . .

1 d / 1 s

. . .

2 d / 1 s

. .

.

3 d / 1 s

. .

.

4 d / 1 s

. . .

1 d / 2 s

. . .

2 d / 2 s

. .

.

3 d / 2 s

. .

.

4 d / 2 s

. .

No zero tracking

2) Unstable Detection

Display Division / Time

.

1 d / s

.

2 d / s

.

3 d / s

.

4 d / s

.

5 d / s

.

No detection

EX-2001 NC RACER ZSME300000091

15

EXCELL PRECISION CO., LTD.

5-2 CALIBRATION SETTING

Please allow the indicator to warm up at least 15 to 30 minutes before calibration.

Switch the capacity calibration switch to “ON” and the display shows .

Press the key and the display shows . then enter the setting mode.

5-2-1 Calibration Procedure

Zero Calibration

Weight Calibration

5-2-2 Zero Calibration

a) Make sure that there are no objects on the weighing platform and press

the key, after the indicator has stabilized the display will show

“ ……. ”. The calibration is completed after about 5 seconds.

b) To skip the “Zero calibration” procedure, press the key.

5-2-3 Weight Calibration

a) Place an accurate weight onto the platform; use the front panel keys to key in

the weight value. Press the key, after the indicator is stabilized the display will

show “ ……. ”. The calibration is completed after about 5 seconds.

b) To skip the weight calibration, press the .

Zero Calibration

Com

p

leted

Confirmation

completed

Switch the calibration

switch to OFF

Place

calibrate

d weight

C A L

ENTER

STANDBY

OPERAE

ENTER

STANDBY

OPERAE

ENTER

STANDBY

OPERAE

ENTER

STANDBY

OPERAE

EX-2001 NC RACER ZSME300000091

16

EXCELL PRECISION CO., LTD.

Before linearity calibration, make sure “Zero calibration” and “Weight Calibration” are properly

performed. Set the calibration switch to ON position.

Press key

Choose the calibration value Press key to previous step

Press key

Press key Press key to previous step

Enter the correct weight value

Press key

The calibrated weight value

is displayed when the

signal is stable

Press to next step

After finishing the first linearity calibration,

choose to continue or exit the linearity mode

by pressing .

◆ Refer to 5-4 Error Messages when any error message appears during the procedure.

5-3 LINEARITY CALIBRATION

.

....

Five point linearity calibration.

Choosing from 1P ~ 5P by

pressing key.

⇒ No linearity

calibration value at this point

⇒ linearity calibration

value present at this point

The weight value is displayed.

⇒ Increase the number of

the flashing digit by one

⇒ Decrease the number

of the flashing digit by

one

⇒ Shift the flashing digit

one space to left

⇒ Shift the flashing digit

one space to right

⇒ Save the settings

⇒ Exit the settings

Press and key to

choose linearity calibration

C A L

ZERO

+

TARE

—

ENTER

ZERO

+

TARE

—

ENTER

STANDBY

OPERAE

ENTER

STANDBY

OPERAE

ENTER

STANDBY

OPERAE

STANDBY

OPERAE

TARE

—

PRINT

ZERO

+

GROSS

NET

ENTER

STANDBY

OPERAE

EX-2001 NC RACER ZSME300000091

17

EXCELL PRECISION CO., LTD.

Recall Linearity correction point

Set the calibration switch to ON position.

Press key

Choose linearity calibration

Press key

After finishing the first linearity calibration,

choose to continue or exit the linearity mode

by pressing .

The weight value is displayed.

⇒ Increase the number of

the flashing digit by one

⇒ Decrease the number

of the flashing digit by

one

⇒ Shift the flashing digit

one space to left

⇒ Shift the flashing digit

one space to right

⇒ Save the settings

⇒ Exit the settings

C A L

ENTER

GROSS

NET

STANDBY

OPERAE

STANDBY

OPERAE

ZERO

+

TARE

—

Five point linearity calibration.

Choosing from 1P ~ 5P by

pressing key.

⇒ No linearity

calibration value at this point

⇒ Linearity

calibration value at this point

TARE

—

PRINT

ZERO

+

GROSS

NET

ENTER

STANDBY

OPERAE

EX-2001 NC RACER ZSME300000091

18

EXCELL PRECISION CO., LTD.

Clear a linearity correction point

Set the calibration switch to ON position.

Press key

Choose linearity calibration

Press key

After finishing the first linearity calibration,

users can choose to continue or exit the

linearity mode by pressing .

Five point linearity calibration.

Choosing from 1P ~ 5P by

pressing key.

⇒ No linearity

calibration value at this point

⇒ Linearity calibration

value at this point

The weight value is displayed.

C A L

ENTER

PRINT

ENTER

STANDBY

OPERAE

TARE

—

ZERO

+

⇒ Increase the number of

the flashing digit by one

⇒ Decrease the number

of the flashing digit by

one

⇒ Shift the flashing digit

one space to left

⇒ Shift the flashing digit

one space to right

⇒ Save the settings

⇒ Exit the settings

TARE

—

PRINT

ZERO

+

GROSS

NET

ENTER

STANDBY

OPERAE

La pagina sta caricando ...

Excell EX-2001NC Racer Manuale utente

Excell EX-2001NC Racer Manuale utente

in altre lingue

Altri documenti