NEC E425 Manuale utente

User’s Manual

E505

E425

E325

E585

English-1

www.necdisplaysolutions.com

Index

Precautions And Reminders �� English-1

Important Safety Instructions �� English-2

Important Information �� English-4

License Notice and Trademark Acknowledgement�� English-8

Declaration Of Conformity �� English-9

Contents �� English-10

Preparation ��English-11

Attaching the Base ��English-11

Using Cable Clamper �� English-12

Preparing Your LCD Display For Wall Mounting (optional) �� English-12

Prohibit portrait condition use �� English-13

Place The Display On A Solid Surface �� English-14

Battery Installation and Replacement�� English-14

Connect To The Power Source �� English-15

Power On/Off Your New LCD Display �� English-15

Power Mode Status �� English-15

Source Connection Guide �� English-17

Operating Instructions �� English-19

Using The Side Panel Controls �� English-19

Using The Remote Control �� English-20

Operating Range for the Remote Control�� English-21

Timing Table �� English-22

Navigating The On-Screen Menu �� English-23

Video Menu �� English-23

Audio Menu �� English-24

Setup Menu �� English-24

USB Menu �� English-26

Maintenance and Recycling �� English-28

Care Of The Screen �� English-28

Mobile Telephone Warning �� English-28

End Of Life Directives�� English-28

Italian Homologation declaration �� English-28

Manufacturer’s Recycling and Energy Information �� English-29

Disposing of your old NEC product �� English-29

Energy Saving �� English-29

WEEE Mark (European Directive 2012/19/EU) �� English-30

Specication �� English-31

Product Specications �� English-31

RS-232C Port Specications �� English-35

Before Calling Service �� English-36

Glossary �� English-37

English-1

English

Precautions And Reminders

Do not place the display

in conned spaces or in a

box when in use� Maintain

ample ventilation for the

display when in use�

Do not open the display

cabinet�

Call a NEC certied

service personnel for any

internal service needed for

your display�

Keep the display away

from direct sunlight, dust,

humidity, smoke and oily

areas�

Unplug immediately if the

display falls�

Unplug immediately if

there is a display malfunc-

tion such as a loss of

audio/video, the presence

of smoke, or a bad odor

coming from the display�

Unplug the AC cord from

the AC outlet before

cleaning� Do not use liquid

cleaners or aerosol clean-

ers to clean the display�

Do not place the display

near water such as a

bathtub, washbasin, sink,

laundry tub, swimming

pool, or a damp base-

ment� Unplug immediately

if the display has been

exposed to rain or water�

Do not cover or block

any vents or openings�

Inadequate ventilation

may shorten the life of

the display and cause

overheating�

Place the unit on a sturdy,

even surface�

Do not insert any foreign

objects into the display

cabinet� Unplug immedi-

ately if objects have fallen

into the display�

Unplug the power cord

from the outlet when

the display is not in use

for long periods of time

(days)�

Notice for Remote Controller

Avoid Liquids

PRE CH

CH-List

Avoid Aerosol Cleaners

PRE CH

CH-List

Avoid Dropping

PRE CH

CH-List

English-3

English-2

Important Safety Instructions

Read before operating equipment

Follow all warnings and instructions marked on this display�

1� Read these instructions�

2� Keep these instructions�

3� Heed all warnings�

4� Follow all instructions�

5� Do not use this apparatus near water�

6� Clean only with dry cloth�

7� Do not block any ventilation openings� Install in accordance with

the manufacturer's instructions�

8� Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including ampliers) that

produce heat�

9� Do not defeat the safety purpose of the polarized or grounding-

type plug� A polarized plug has two blades with one wider than the

other� A grounding type plug has two blades and a third grounding

prong� The wide blade or the third prong are provided for your

safety. If the provided plug does not t into your outlet, consult an

electrician for replacement of the obsolete outlet�

10� Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point where

they exit from the apparatus�

11� Only use attachments/accessories specied by the manufacturer.

12� Use only with the cart, stand, tripod, bracket, or table specied by

the manufacturer, or sold with the apparatus� When a cart is used,

use caution when moving the cart/apparatus combination to avoid

injury from tip-over�

S3125A

13� Unplug this apparatus during lightning storms or when unused for

long periods of time�

14� Refer all servicing to qualied service personnel. Servicing is

required when the apparatus has been damaged in any way, such

as power-supply cord or plug is damaged, liquid has been spilled

or objects have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally, or has

been dropped� Unplug immediately if the display faces above

condition�

English-3

English-2

English

15� The display complies with the recommended safety standards

for stability� Do not put excessive force on the front or top of

the cabinet� This could cause the product to tip over and cause

damage and/or personal injury�

16� If display or glass is broken, do not come in contact with the liquid

crystal and handle with care�

17� Follow instructions for wall, shelf or ceiling mounting as

recommended by the manufacturer�

18� Rest your eyes periodically by focusing on an object at least 5 feet

away� Blink often�

19� Do not place any heavy objects on the power cord�

Damage to the cord may cause shock or re.

20� Do not use display in high temperature, humid, dusty, or oily areas�

21� Do not bend, crimp or otherwise damage the power cord�

22� Apparatus shall not be exposed to dripping or splashing and no

objects lled with liquids, such as vases, shall be placed on the

apparatus

WARNING:

To prevent the apread of re, keep

candles or other open ames away fram this

product at all times�

IMPORTANT INFORMATION

If a display is not positioned in a sufciently stable location, it can

be potentially hazardous due to falling� Many injuries, particularly to

children, can be avoided by taking simple precautions such as:

• Using cabinets or stands recommended by the manufacturer of the

display�

• Only using furniture that can safely support the display�

• Ensuring the display is not overhanging the edge of the supporting

furniture�

• Not placing the display on tall furniture (for example, cupboards or

bookcases) without anchoring both the furniture and the display to a

suitable support�

• Not standing the displays on cloth or other materials placed between

the display and supporting furniture�

• Educating children about the dangers of climbing on furniture to reach

the display or its controls�

English-5

English-4

Important Information

WARNING

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO

RAIN OR MOISTURE� ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG

WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE

PRONGS CAN BE FULLY INSERTED�

REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE

COMPONENTS INSIDE�

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL�

CAUTION

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE

POWER CORD IS UNPLUGGED FROM WALL SOCKET� TO FULLY

DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT

THE POWER CORD FROM THE AC OUTLET� DO NOT REMOVE

COVER (OR BACK)� NO USER SERVICEABLE PARTS INSIDE�

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL�

This symbol warns user that uninsulated voltage within the unit may

have sufcient magnitude to cause electric shock. Therefore, it is

dangerous to make any kind of contact with any part inside this unit�

This symbol alerts the user that important literature concerning the

operation and maintenance of this unit has been included� Therefore, it

should be read carefully in order to avoid any problems�

CAUTION:

Please use the power cord provided with this display in accordance with the

table below� If a power cord is not supplied with this equipment, please contact

your supplier� For all other cases, please use a power cord that matches the

AC voltage of the power outlet and has been approved by and complies with

the safety standard of your particular country�

Plug Type

European

Continental

U.K. Japanese North America

Plug Shape

Region

EU

(except U�K�)

U�K� Japan U�S�A�/Canada

Voltage

230 230 100 120

This LCD display operates on 100-240 volts 50-60 Hz, AC current� Insert the

power cord into a 100-240 volts 50-60 Hz outlet� The mains plug is used as

the disconnect device and shall remain readily operable�

English-5

English-4

English

To prevent electric shock from the display, do not use with an extension cord,

receptacle, or other outlet unless the blades and ground terminal can be fully

inserted to prevent blade exposure�

Never connect the LCD display to other than the specied voltage.

CAUTION:

Never remove the back cover of the LCD display as this can expose you to

very high voltages and other hazards� If the display does not operate properly,

unplug the LCD display and call your authorized dealer or service center�

Adjust only those controls that are covered in the instructions, as improper

changes or modications not expressly approved by NEC could void the

user’s warranty�

Batteries installed warning

Incorrect usage of batteries can result in leaks or bursting�

NEC recommends the following battery use:

• Do not mix battery brands�

• Danger of explosion if battery is incorrectly replaced� Replace only with

the same or equivalent type�

• Do not combine new and old batteries� This can shorten the battery life

or cause liquid leakage of the batteries�

• Remove dead batteries immediately to prevent battery acid from leaking

into the battery compartment�

• Do not touch exposed battery acid as it may injure skin�

• Remove the batteries if you do not intend to use the remote control for a

long period of time�

• The batteries shall not be exposed to excessive heat such as sunshine,

re or the like�

Image persistence

Please be aware that LCD Technology may experience a phenomenon

known as Image Persistence� Image Persistence occurs when a residual or

"ghost" image of a previous image remains visible on the screen� Unlike CRT

monitors, LCD monitors' image persistence is not permanent, but constant

images being displayed for a long period of time should be avoided� To

alleviate image persistence, turn off the display for as long as the previous

image was displayed� For example, if an image was on the display for one

hour and a residual image remains, the display should be turned off for one

hour to erase the image�

NOTE:

As with all personal display devices, NEC DISPLAY SOLUTIONS recommends

displaying moving images and using a moving screen saver at regular intervals

whenever the screen is idle or turning off the display when not in use�

English-7

English-6

CAUTION:

These servicing instructions are for use by qualied service personnel only.

To reduce the risk of electric shock, do not perform any servicing other than

that contained in the operating instructions unless you are qualied to do so.

Ventilation

The slots and openings in the display are provided for necessary ventilation�

To ensure reliable operation of the display and to protect it from overheating,

these slots and openings must never be blocked or covered�

Unless proper ventilation is provided, the display may gather dust and get

dirty� For proper ventilation, observe the following:

• Do not install the display face up, down or sideways�

• Do not install the display turned over or upside down�

• Never cover the slots and openings with a cloth or other materials�

• Never block the slots and openings by placing the display on a bed,

sofa, rug or other similar surface�

• Never place the display in a conned space, such as a bookcase or

built-in cabinet, unless proper ventilation is provided�

Leave some space around the display set as shown below� Otherwise, air-

circulation may be inadequate and will cause overheating, which may cause a

re or damage to the display set.

Install on the wall

11 7/8 inches

4 inches

30 cm

10 cm10 cm

Leave at least this space

around the set.

4 inches

10 cm

2.36 inches

6 cm

English-7

English-6

English

For use only with UL Listed Wall Mount Bracket with minimum weight/load:

Please refer to the Specication on page 31.

Unit without base weight: The equipment and its associated mounting means

still remain secure during the test�

Used wall mounting kit, VESA-compatible wall bracket distance, diameter of

Screw dimension: Please refer to the Specication on page 31.

Installed with stand

11 7/8 inches

30 cm

Leave at least this space

around the set.

4 inches

10 cm

4 inches

10 cm

4 inches

10 cm

Never install the display set where air-circulation is blocked�

Objects and ventilation holes

Never push objects of any kind into the display through the cabinet slots as

they may touch dangerous voltage points or short out parts that could result in

a re or an electric shock. Do not place any objects on the display.

English-9

English-8

License Notice and Trademark

Acknowledgement

Windows is a registered trademark of Microsoft Corporation�

NEC is a registered trademark of NEC Corporation�

All other brands and product names are trademarks or registered trademarks

of their respective owners�

®

HDMI, the HDMI logo and High-Denition Multimedia Interface are trademarks

or registered trademarks of HDMI Licensing LLC in the United States and

other countries�

English-9

English-8

English

Declaration Of Conformity

This device complies with Part 15 of FCC Rules� Operation is subject to the

following two conditions� (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including

interference that may cause undesired operation�

U.S. Responsible Party: NEC Display Solutions of America, Inc.

Address: 500 Park Boulevard, Suite 1100

Itasca, Illinois 60143

Tel. No.: (630) 467-3000

Type of Product: Display

Equipment Classication: Class B Peripheral

Model: E585

E505

E425

E325

We hereby declare that the equipment specied above

conforms to the technical standards as specied in the FCC Rules.

Canadian Department of Communications Compliance Statement

DOC: This Class B digital apparatus meets all requirements of the Canadian

Interference-Causing Equipment Regulations�

C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations

according to CAN/CSA C22�2 No� 60065-03�

FCC information

1� Use the attached specied cables with the E585/E505/E425/E325 color display so

as not to interfere with radio and television reception�

(1) Please use the supplied power cord or equivalent to ensure FCC compliance�

(2) Please use the supplied shielded video signal cable, Mini D-SUB 15pin to Mini

D-SUB 15 pin�

2� This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules� These limits are designed

to provide reasonable protection against harmful interference in a residential

installation� This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications� However, there is no guarantee that

interference will not occur in a particular installation� If this equipment does cause

harmful interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna�

• Increase the separation between the equipment and receiver�

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected�

• Consult the dealer or an experienced radio/TV technician for help�

Canadian notice

CAN ICES-3 (B) / NMB-3(B)

English-11

English-10

Contents

Your new NEC display box*

1

should contain the following:

• Display

• Power cord*

2

• D-sub Cable

• Remote Control

• 1�5V AAA Size Batteries x2

• Setup Manual x1

• CD ROM

Setup Manual

E585 / E505 / E425 / E325

Video Signal Cable

(Mini D-SUB 15 pin to

Mini D-SUB 15 pin)

(EU)

Power Cord*

2

Wireless Remote Control

and AAA Batteries

Setup Manual CD-ROM

NOTE:

*1: Remember to save your original box and packing material to transport or ship the

display�

*2: Type and number of power cords included will depend on the where the display is

to be shipped� When more than one power cord is included, please use a power

cord that matches the AC voltage of the power outlet and has been approved by and

complies with the safety standard of your particular country�

*3: The following stand base and screw are option parts�

E585: M4 (14mm) x 6

E505: M6 (20mm) x 4

E425/E325: M4 (20mm) x 4

Stand Base

(E585) (E505/E425/E325)

Stand Screw

English-11

English-10

English

Preparation

IMPORTANT:

Do not apply pressure to the screen display area which may

compromise the integrity of the display� The manufacturer’s warranty does not

cover user abuse or improper installations�

Attaching the Base

E585

Stand Screw x 6

E585:M4 (14mm)

E505 / E425 / E325

Stand Screw x 4

E505:M6 (20mm)

E425/E325:M4 (20mm)

1� Place the display face down on a soft and at surface to prevent

scratching and damage�

2� Carefully align the base to the button of the display and fasten the screws

with a cross-head screwdriver�

CAUTION:

The base of the stand is very heavy� Install with care to avoid injury such as dropping

the base onto one's foot�

English-13

English-12

Using Cable Clamper

Tie the cables together using the cable clamper�

Preparing Your LCD Display For Wall Mounting

(optional)

We suggest that you keep your display at least 2�36 inches (60 mm) from the

wall to prevent cable interference� Before mounting your display on the wall,

you need to remove the base� For your safety, only mount with a UL listed wall

mount bracket that supports the weight of the display� (Please see page 31�)

To attach a wall mount bracket to your display:

E585 E505/E425/E325

Neck Screw

VESA Hole

Neck Screw

VESA Hole

1� Loosen the screws on the button of the base, and remove the base�

2� Secure the wall mount bracket to the back of your display using four M4

screws (for 32" only) or M6 screws(for 42"/50"/58" only)�

screen size (inches) required pitch (mm) VESA hole depth

58 400 x 400 4 x M6 (22 mm)

50 200 x 400 4 x M6 (15 mm)

42 200 x 200 4 x M6 (15 mm)

32 100 x 100 4 x M4 (12�5 mm)

English-13

English-12

English

NOTE:

Wall mounting solution is not included with the unit and is sold separately� Contact your

NEC representative for details�

It is necessary to provide screw of appropriate length (Wall mount bracket thickness +

VESA hole depth)�

Prohibit portrait condition use

CAUTION:

Do not rotate the diplay from landscape to portrait�

English-15

English-14

Place The Display On A Solid Surface

Ensure that the LCD display is

placed in a position to allow free ow

of air� Do not cover the ventilation

openings on the back cover� Do not

place the display near any open

ames. Do not allow the display to

be placed in an environment where

it can be exposed to heat, direct

sunlight, or rain and water� Do not

expose the equipment to any liquid�

Battery Installation and Replacement

The remote control is powered by two 1�5V AAA batteries� To install or replace

batteries:

1� Open the battery cover of the remote

control by pushing and pulling it in the

direction of the arrow�

2� Insert two new “AAA” size batteries

for the remote control� When

replacing old batteries, push them

towards the springs and lift them out�

3� Match the batteries to the (+) and (-)

marks in the battery compartment�

4� Insert the bottom of the battery, the

(-) side, into the battery compartment

rst, push towards the springs and

insert the top of the battery, the (+)

side, into place� Do not force the

battery into the battery compartment�

5� Close the battery cover making sure the tabs rest in the corresponding

holes and push down the cover until it clicks shut�

Min

1 m

English-15

English-14

English

Connect To The Power Source

The display should be installed close to an easily accessible power outlet�

Fully insert the prongs into the power outlet socket� A loose connection may

cause image degradation�

If there is power to the display, the front LED at the bottom of the display will

be either none or red� A red LED means the display is in standby mode�

Power On/Off Your New LCD Display

Press the power button on the remote control or press the power button

located on the side of the display� The display will power on�

Power button

or

Power Mode Status

Mode On Standby Warming up

LED Status

None Red Blinking Red

When in on mode, the Display operates as follows if no external signal is

input�

1� When the external device is connected to the VGA terminal, the NO

SIGNAL menu is displayed and 15 seconds later the Display switches to

English-17

English-16

warming up mode�

2� In warming up mode, when the Display receives a signal from an external

VGA device, it switches automatically to on mode�

NOTE:

Note that in warming up mode, the Display does not switch automatically

to on mode even if a signal is input from an external device using HDMI,

component video or composite video�

If the power cord is unplugged during warming up mode, the Display will

starts in standby mode the next time it is turned on�

3� When the external device is connected to another terminal (HDMI,

component video, composite video), the NO SIGNAL menu is displayed

and 15 minutes later the Display switches to standby mode�

4� In standby mode, press the power button on the remote control or on the

side panel to switch the Display to on mode�

NOTE:

Note that in standby mode, the Display does not switch automatically to on

mode even if a signal is input from an external device using VGA, HDMI,

component video or composite video�

If the power cord is unplugged during standby mode, the Display will starts in

the same standby mode the next time it is turned on�

TIP:

When Home mode is set under Energy Options in the on-screen display

menu, the Display switches to power saving mode if no external signal is

input�

When Retail mode is set under Energy Options in the on-screen display

menu, the Display does not switch to power saving mode when no external

signal is input�

When On is set under Auto Power Off in the on-screen display menu, the

Display automatically turns off if the user does not operate the Display for

more than 4 hours�

When the sleep timer has been set in the on-screen display menu, the

Display automatically turns off after the set time has elapsed�

English-17

English-16

English

Source Connection Guide

E585

❶

❷

❸

❹

❺❻

AC POWER

1�

RS-232C –

Connect to your PC, and receive the control commands from

the PC�

2�

HDMI (HDMI1, HDMI2, HDMI3) –

Connect to your HDMI devices�

3�

USB port –

Used for accessing photo, music, and movie les.

4�

PC IN (VGA / AUDIO) –

Connect to your PC video and audio�

5�

COMPONENT / AV IN –

• Component: Connect to digital video equipment to the Video Green (Y),

Blue (Pb), Red (Pr) jacks, and matching Audio White (L) and Red (R)

jacks�

• Composite: Connect to digital video equipment to the Video Green (AV),

jacks, and matching Audio White (L) and Red (R) jacks�

6�

SPDIF OUT-

Use a digital audio cable to connect to stereo home theater

system�

English-19

English-18

E505 / E425 / E325

E325 / E425 E505

AC POWER

❶

❷

❸

❹

❺❻

1�

RS-232C –

Connect to your PC, and receive the control commands from

the PC�

2�

HDMI (HDMI1, HDMI2, HDMI3) –

Connect to your HDMI devices�

3�

USB port –

Used for accessing photo, music, and movie les.

4�

PC IN (VGA / AUDIO) –

Connect to your PC video and audio�

5�

COMPONENT / AV IN –

• Component: Connect to digital video equipment to the Video Green (Y),

Blue (Pb), Red (Pr) jacks, and matching Audio White (L) and Red (R)

jacks�

• Composite: Connect to digital video equipment to the Video Green (AV),

jacks, and matching Audio White (L) and Red (R) jacks�

6�

SPDIF OUT-

Use a digital audio cable to connect to stereo home theater

system�

Once your AV device is connected, press the

Source

button on the remote control to select the

relevant source to view� (ex: Press

COMP

button

to select “Component” if you have connected a

source to the Component input�)

PRE CH

La pagina sta caricando ...

NEC E425 Manuale utente

Questo manuale è adatto anche per

NEC E425 Manuale utente

in altre lingue

Documenti correlati

Altri documenti