Thermo Fisher Scientific TSX Manuale utente

Ultra Low

Temperature Freezers

TSX series

Installation and Operation

328442H01 Rev. H Dec 2018

Visit us online to register your warranty

www.thermofisher.com/labwarranty

IMPORTANT Read this instruction manual. Failure to follow the instructions in this manual can result

in damage to the unit, injury to operating personnel, and poor equipment performance.

CAUTION All internal adjustments and maintenance must be performed by qualified service personnel.

Material in this manual is for informational purposes only. The contents and the product it describes are

subject to change without notice. Thermo Fisher Scientific makes no representations or warranties with

respect to this manual. In no event shall Thermo be held liable for any damages, direct or incidental,

arising from or related to the use of this manual.

Contents

Models .......................................................................................1

Safety Precautions....................................................................2

Unpacking.................................................................................4

Packing List ..............................................................................5

General Recommendations .....................................................6

Temperature Monitoring ...................................................... 6

General Usage ...................................................................... 6

Initial Loading...................................................................... 6

Battery Door Opening / Closing .......................................... 7

Operating Standards ...............................................................8

Electrical Specifications....................................................... 8

Installation................................................................................9

Location ............................................................................... 9

Wiring .................................................................................. 9

Leveling ............................................................................. 10

Backup System (Optional) ................................................. 10

Super Insulated Cabinet Construction................................ 10

Door Operation .................................................................. 10

Pressure Equalization Port ................................................. 12

Installing the Remote Alarm Connector ............................ 12

Intended Use ...................................................................... 13

Start Up...................................................................................14

Connectivity Requirements................................................ 14

Initial Start Up.................................................................... 15

Standby Mode .................................................................... 27

Operation................................................................................28

Operation Overview........................................................... 28

Home Screen ...................................................................... 28

Settings............................................................................... 29

Event Log........................................................................... 39

Alarms................................................................................ 41

Users................................................................................... 41

Reports ............................................................................... 44

Chart................................................................................... 45

Health Status and Alarm Management ...............................49

Health Status Overview ..................................................... 49

Notifications / Cautions ..................................................... 51

Alarms / Warning............................................................... 52

Contents

Backup System (Optional) ....................................................53

CO2 and LN2 Precautions ................................................. 53

Installation.......................................................................... 54

Start Up .............................................................................. 55

Operation............................................................................ 55

Chart Recorders (Optional)..................................................56

Set Up and Operation......................................................... 56

Changing Chart Paper ........................................................ 57

Calibration Adjustment ...................................................... 57

Maintenance and Troubleshooting.......................................58

Cleaning the Condenser ..................................................... 58

Cleaning the Condenser Filter............................................ 58

Gasket Maintenance........................................................... 58

Defrosting the Freezer........................................................ 59

Battery Maintenance .......................................................... 59

Maintenance Schedule ....................................................... 60

Troubleshooting Guide..........................................................61

Warranty ................................................................................65

Warranty (International) ......................................................66

Appendix A: Alarm Summary .................................................67

Appendix B: Event Log Detail ................................................73

Appendix C: City Time Zone ..................................................75

Models

Thermo Fisher Scientific Ultra Low Temperature Installation and Operation 1

1 Models

* Note Energy Star is not applicable to the G and V models.

Brand - Model Size (xxx) Voltage (*)

Thermo Scientific – TSXxxx86* 400 / 500 / 600 / 700 A / D / V / G

Safety Precautions

2 Installation and Operation Thermo Fisher Scientific Ultra Low Temperature

2 Safety Precautions In this manual, the following symbols and conventions are used:

This symbol used alone indicates important operating instructions which

reduce the risk of injury or poor performance of the unit.

CAUTION: This symbol, in the context of a CAUTION, indicates a

potentially hazardous situation which if not avoided could result in minor to

moderate injury or damage to the equipment.

WARNING: This symbol indicates potentially hazardous situations which,

if not avoided, could result in serious injury or death.

WARNING: This symbol indicates situations where dangerous voltages

exist and potential for electrical shock is present.

The snowflake symbol indicates extreme low temperatures and high risk of

frostbite. Do not touch bare metal or samples with unprotected body parts.

This symbol indicates a need to use gloves during the indicated procedures.

If performing decontamination procedures, use chemically resistant gloves.

Use insulated gloves for handling samples and when using liquid nitrogen.

Before installing, using or maintaining this product, please be sure to read

this manual and product warning labels carefully. Failure to follow these

instructions may cause this product to malfunction, which could result in

injury or damage.

Safety Precautions

Thermo Fisher Scientific Ultra Low Temperature Installation and Operation 3

Below are important safety precautions that apply to this product:

Use this product only in the way described in the product literature and in

this manual. Before using it, verify that this product is suitable for its

intended use. If this equipment is used in a manner not specified by the

manufacturer, the protection provided by the equipment may be impaired.

Do not modify system components, especially the controller. Use OEM

exact replacement equipment or parts. Before use, confirm that the product

has not been altered in any way.

WARNING: Your unit must be properly grounded in conformity with

national and local electrical codes. Never connect the unit to overloaded

power sources.

WARNING: Disconnect the unit from all power sources before cleaning,

troubleshooting, or performing other maintenance on the product or its

controls.

WARNING: “Caution, risk of fire”. This unit is charged with hydrocarbon

refrigerants.

Unpacking

4 Installation and Operation Thermo Fisher Scientific Ultra Low Temperature

3 Unpacking At delivery, examine the exterior for physical damage while the carrier’s

representative is present. If exterior damage is present, carefully unpack and

inspect the unit and all accessories for damage.

If there is no exterior damage, unpack and inspect the equipment within five

days of delivery. If you find any damage, keep the packing materials and

immediately report the damage to the carrier. Do not return goods to the

manufacturer without written authorization. When submitting a claim for

shipping damage, request that the carrier inspect the shipping container and

equipment.

Packing List

Thermo Fisher Scientific Ultra Low Temperature Installation and Operation 5

4 Packing List Inside the freezer cabinet is a bag containing:

• This manual

• A handle lock key

• A CD with user’s manuals, including translated versions

• Certificates of conformance and calibration

• A remote alarm contact connector

• Posts for rear spacing

If you have ordered a field-installed chart recorder, the bag will also contain:

• Recorder installation instructions

• Extra inkless paper

If you have ordered a backup system, the cabinet will also contain:

• A hose assembly

• English and metric connectors

If specified on the order, the bag may also include:

• A QC temperature graph and test log

• Calibration information

If you have ordered the Proximity Access Card Option, the cards will be in a

bag attached to the front of the freezer.

General Recommendations

6 Installation and Operation Thermo Fisher Scientific Ultra Low Temperature

5 General

Recommendations

5.1 Temperature

Monitoring

IMPORTANT NOTE We recommend the use of a redundant and

independent temperature monitoring system so that the freezer can be

monitored continuously for performance commensurate with the value of

product stored.

5.2 General Usage This refrigeration system is designed to maintain ultra-low temperatures

with safety in an ambient environment within 15°C to 32°C (59°F to 90°F),

only when the freezer is used for storage. For TSX 700 models, the

maximum operating environment is 28°C (83°F).

WARNING: This unit is not a “rapid-freeze” device. Freezing large

quantities of liquid, or high-water content items, will temporarily increase

the chamber temperature and will cause the compressors to operate for a

prolonged time period.

Avoid opening the door for extended time periods since chamber

temperature air will escape rapidly. Also, keep the inner doors closed as

much as possible. When room air, which is higher in humidity, replaces

chamber air, frost may develop in the chamber more rapidly.

5.3 Initial Loading Allow the freezer to operate at the desired temperature for a minimum

of 12 hours before loading.

Load the freezer one shelf at a time, beginning with the top shelf. After

loading each shelf, allow the freezer to recover to the desired set point before

loading the next shelf. Repeat this process until the freezer is fully loaded.

CAUTION: Failure to follow these procedures or overloading the unit may

cause undue stress on the compressors or jeopardize user product safety.

General Recommendations

Thermo Fisher Scientific Ultra Low Temperature Installation and Operation 7

5.4 Battery Door

Opening / Closing

To open the grille door, pull the door from the top right corner as shown in

the figure below.

To close the grille door, push the door against frame to hold latch in

position.

Figure 1. Door Opening

Operating Standards

8 Installation and Operation Thermo Fisher Scientific Ultra Low Temperature

6 Operating

Standards

The freezers described in this manual are classified for use as stationary

equipment in a Pollution Degree 2 and Over voltage Category II

environment.

These units are designed to operate under the following environmental

conditions:

• Indoor use

• Altitude up to 2000 m

• Maximum relative humidity 60% for temperatures within 15°C to 32°C

(59°F to 90°F). For TSX 700 models, the maximum operating

environment is 28°C (83°F).

• Main supply voltage fluctuations not to exceed ±10% of the nominal

voltage.

• For the TSX series, the ULT should not be connected to a GFCI

(Ground Fault Circuit Interrupter) protected outlet as it may be subject

to nuisance tripping.

6.1 Electrical

Specifications

The last character in the model number listed on the dataplate identifies the

electrical specifications for your unit.

Specific unit current rating is listed on

the dataplate.

The voltage types are A, D, V and G as specified in the following table:

Table 1. TSX Series Electrical Specifications

Model Voltage Frequency Current

400D/V 208-230 V 50/60 Hz 4.0 A

400A 115 V 60 Hz 9.0 A

400G 100 V 50/60 Hz 10.5 A

500D 208-230 V 60 Hz 5.1 A

500V 208-230 V 50 Hz 5.2 A

500A 115 V 60 Hz 9.5 A

500G 100 V 50/60 Hz 9.5 A

600D/V 208-230 V 50/60 Hz 4.0 A

600A 115 V 60 Hz 8.5 A

600G 100 V 50/60 Hz 9.5 A

700D 208-230 V 60 Hz 5.8 A

700V 208-230 V 50 Hz 6.1 A

700A 115 V 60 Hz 10.6 A

Installation

Thermo Fisher Scientific Ultra Low Temperature Installation and Operation 9

7 Installation

WARNING: Do not exceed the electrical rating printed on the data plate

located on the lower left side of the unit.

7.1 Location Install the unit in a level area free from vibration with a minimum of 8 inch

(20 cm) of space on the top and sides, 6 inch (15 cm) in back. Refer to

Section 7.3 for further instructions on leveling cabinets. Allow enough

clearance so that door can swing open at least 85°.

The rear spacing posts provided with the freezer can be used to ensure

proper clearance. To install the spacing posts, screw them into the back in

the rear deck area.

Do not position the equipment in direct sunlight or near heating diffusers,

radiators, or other sources of heat. The ambient temperature range at the

location must be 15°C to 32°C (59°F to 90°F). For TSX 700 models, the

maximum operating environment is 28°C (83°F).

7.2 Wiring

CAUTION: Connect the equipment to the correct power source. Incorrect

voltage can result in severe damage to the equipment.

CAUTION: For personal safety and trouble-free operation, this unit must

be properly grounded before it is used. Failure to ground the equipment

may cause personal injury or damage to the equipment. Always conform to

the National Electrical Code and local codes. Do not connect the unit to

overloaded power lines.

CAUTION: Do not position the unit in a way that impedes access to the

disconnecting device or circuit breaker in the back of the unit.

CAUTION: Always connect the freezer to a dedicated (separate) circuit.

Each freezer is equipped with a service cord and plug designed to connect it

to a power outlet which delivers the correct voltage. Supply voltage must be

within ±10% of the freezer rated voltage.

CAUTION: Never remove or disable the grounding prong from the service

cord plug. If the prong is removed, the warranty is invalidated.

Installation

10 Installation and Operation Thermo Fisher Scientific Ultra Low Temperature

7.3 Leveling Make sure that the floor is level. The unit must be level both front to back

and side to side.

400 box capacity models are equipped with one leveling leg on the right

hand side. These may be used to help prevent the unit from shifting during

a door opening.

Be certain to lock the brakes for units equipped with casters.

7.4 Backup System

(Optional)

If you are using a CO2 or LN2 backup system, refer to Section 11 for

installation and operation instructions.

7.5 Super Insulated

Cabinet Construction

In all models, the cabinet walls have a vacuum insulation core encapsulated

by a sealed film laminate.

CAUTION: Never drill holes in or near the cabinet walls. Drilling could

damage the insulation and make the unit inoperable.

7.6 Door Operation Upright freezer models are equipped with an advanced assembly specifically

designed for ultra-low temperature freezers.

Features include:

• One-hand operation

• A front-accessible lock

• Hasps for a standard padlock to provide additional security. Length of

the shackle must be between 3/4 inch (1.9 cm) and 11/2 inch (3.8 cm).

• Durable construction for reliable operation and safe product storage.

• Door ramp alignment feature

• Optional controlled access to the freezer with Proximity Access cards.

CAUTION: When moving the freezer, always grasp cabinet surfaces; never

pull the freezer by the latch handle.

7.6.1 Opening the Door For freezers with the Proximity Access Card option:

1. Remove the padlock if installed.

Installation

Thermo Fisher Scientific Ultra Low Temperature Installation and Operation 11

2. To unlock the door, pass the card in front of the freezer below the LCD

display.

3. Grasp the latch handle and pull it toward yourself until the latch

disengages from the cabinet strike.

4. Keep pulling by the latch handle to open the main door.

For freezers without the Access Card option:

1. Remove the padlock if installed.

2. Grasp the latch handle and pull it toward yourself until the latch

disengages from the cabinet strike.

3. Keep pulling by the latch handle to open the main door.

7.6.2 Opening the Door During

a Power Outage

In case of power outage and a unit that has the Proximity Access Card

option, you may use a 9 volt battery to activate the system. To access the

9 volt terminal, remove the USB cover and locate the battery terminals.

Once the terminals are exposed, open the door by holding the 9 volt battery

against the terminals and pass a valid proximity card below the display area.

Once the door is open, remove the 9 volt battery.

Note The terminals are polarized therefore orient the 9 volt battery properly.

7.6.3 Closing the Door Note The latch does not self-engage automatically when you close the door. You

must rotate the latch into the open position first.

1. Grasp the latch handle (preferably with your left hand) and pull it

toward yourself, rotating the latch into the open position.

2. Move the freezer door into the closed position and gently push the

handle away from you, making sure that the latch engages fully with the

cabinet strike.

3. Keep applying gentle pressure to the latch handle until the latch is

securely in closed position.

4. Insert the key and rotate counterclockwise to lock.

5. Replace the padlock as required.

Installation

12 Installation and Operation Thermo Fisher Scientific Ultra Low Temperature

7.7 Pressure

Equalization Port

When an upright ultra-low temperature freezer door is opened, room

temperature air rushes into the storage compartment. When the door is

closed, the fixed volume of air is cooled rapidly. Pressure drops below

atmospheric pressure, resulting in a substantial vacuum. Re-entry into the

cabinet is impossible until internal pressures are returned to atmospheric

pressure. Without a pressure equalization mechanism, it can take, in

extreme cases, several hours before the door can easily be reopened.

All upright models feature a port that provides vacuum relief after door

openings. The pressure equalization port is located in the door behind the

eye-level panel on the front of the freezer. Although the port is designed to

self-defrost, excessive frost accumulation on the inner door could eventually

restrict air flow. Therefore you should periodically inspect the inner door

and brush away any loose frost using a stiff nylon brush.

7.8 Installing the

Remote Alarm

Connector

The remote alarm contacts are located on the back of the freezer above and

to the left of the power switch. After installing the wiring from the remote

alarm to the connector, install the connector to the freezer micro-board.

The pin configuration is shown in Figure 2 below.

Figure 2. Remote Alarm Pin Configuration

The contacts will trip in the event of a power outage, high temperature

alarm, low temperature alarm or door ajar alarm.

Installation

Thermo Fisher Scientific Ultra Low Temperature Installation and Operation 13

7.9 Intended Use The –86°C freezer (refer to Section 1 for the specific model series) described

in this manual are high performance units for professional use. These

products are intended for use as cold storage in research use and as a general

purpose laboratory freezer, storing samples or inventory at operating

temperatures between –50°C and –80°C.

It is not considered a medical device and has therefore not been registered

with a medical device regulatory body (e.g. FDA): that is, it has not been

evaluated for the storage of samples for diagnostic use or for samples to be

re-introduced to the body.

This unit is not intended for use in classified hazardous locations, nor to be

used for the storage of flammable inventory.

Start Up

14 Installation and Operation Thermo Fisher Scientific Ultra Low Temperature

8 Start Up

8.1 Connectivity

Requirements

There are two requirements to take full advantage of your freezers

connectivity options:

1. The freezer needs to be connected to a wireless network with internet

connection, the freezer is only able to use a wireless connection.

a. Please speak with your IT about the correct wireless network and

password to use.

2. A Thermo Fisher Connect account.

b. If you do not already have a Thermo Fisher Connect account, using

a web browser, open the URL below.

https://www.thermofisher.com/mysso/loginDisplay

Then choose the “create an account” option.

8.1.1 Specifications

Note Thermo Fisher Connected devices do not support the use of proxy servers

and enterprise networks which require identity/username for internet access.

Table 2. Specifications

Parameter Specification

Default Wi-Fi transmission frequency to the cloud

Every 5 minutes for sensor

data transmission.

Real-time for alarm events

WiFi protocol 802.11ac

Wi-Fi Security

WEP

WPA/WPA2-PSK

WPA/WPA2-EAP

Wi-Fi Data Rate 1-65 Mbps

Wi-Fi Range Up to 70 meters

Minimum Required Wireless Signal -70 dbM

Firewall Ports that must open 80, 123, 443

Start Up

Thermo Fisher Scientific Ultra Low Temperature Installation and Operation 15

8.1.2 In case of Failure If your freezer is unable to connect to either a wireless network or a cloud

account, please verify your name and password, and attempt to re-connect.

If issues persist, please contact Your Local Support.

Note If your network password expires or changes, your freezer will no longer

connect automatically. Be sure to manually update your password in the freezer

user interface settings to reconnect. Failure to reconnect within 3 days will result

in data loss.

8.2 Initial Start Up To start up the freezer, complete the following steps:

1. Plug the freezer into the power outlet.

2. Turn the power switch in back of the freezer, on the bottom right, to the

ON position.

3. Once the freezer is powered up, the Thermo Scientific logo is displayed

on the front screen. If this is the first time the unit is being turned on, an

initial setup must be completed. Tap the Start Setup button to initiate

the setup.

Figure 3. Main Screen

Start Up

16 Installation and Operation Thermo Fisher Scientific Ultra Low Temperature

The first step of the setup is to select the language. This screen allows you to

specify the preferred display language. Once the language is selected, tap the

Next button.

Figure 4. Language Selection Screen

The next screen allows you to select your location. Enter the name of the

city and select from the list of suggestions displayed. Enable the Auto-sync

with network option by sliding the toggle button.

After selecting the region, tap the Next button.

Figure 5. Region Setup Screen

When entering your “City” into Region Setup screen, refer to “Appendix C: City

Time Zone” . Follow the table to select the city closest to your time zone.

La pagina sta caricando ...

Thermo Fisher Scientific TSX Manuale utente

Thermo Fisher Scientific TSX Manuale utente

in altre lingue

Documenti correlati

Altri documenti