Pottinger TERRADISC 4001 Istruzioni per l'uso

Operator‘s manual

Translation of the original Operating Manual

Nr.

TERRADISC 3001

(Type

9771 :

+ . . 01702

)

TERRADISC 3001multiline

(Type

9771 :

+ . . 01702

)

TERRADISC 3501

(Type

9772 :

+ . . 00352

)

TERRADISC 4001

(Type

9773:

+ . . 00275)

TERRADISC 4001multiline

(Type

9773:

+ . . 00275)

Disc harrow

99+9771.EN.80U.0

1900_GB-PAGE 2

Product liability, information obligation

Product liability obliges manufacturers and dealers to issue operating instructions for the machine at the point of sale and to instruct

the customer on the operation, safety and maintenance regulations governing the machine.

Confirmation is required to prove that the machine and the operating instructions have been properly handed over. For this purpose

you have received a confirmation e-mail from Pöttinger. If you have not received this mail, please contact your local dealer. Your

dealer can fill in the handover declaration online.

For the purposes of product liability law, every farmer is an entrepreneur.

In the terms of product liability law, damage to property is any damage arising due to the machine, but not to the machine, and an

excess (500 euros) exists for this liability.

Corporate damage to property within the terms of the product liability law is excluded from this liability.

Be advised!

The operating instructions must also be handed over with any subsequent machine sale or transfer and the transferee

must be instructed in the regulations stated.

Pöttinger - Trust creates Afnity - since 1871

"Quality pays for itself." Therefore we apply the highest quality standards to our products which are constantly monitored by our

in-house quality management and our management board. Because the safety, perfect function, highest quality and absolute

reliability of our machines in operation are the core competencies for which we stand.

There may be deviations between these instructions and the product as we are constantly developing our products. Therefore no

claims may be derived from the data, illustrations and descriptions. Please contact your Specialist Service Centre for any binding

information about specific features of your machine.

We would ask you to please understand that changes to the scope of supply with regard to form, equipment and technical

specifications are possible at any time.

Any form of reprint, translation or reproduction, including excerpts, requires the written approval of Pöttinger Landtechnik GmbH.

All rights according to copyright laws remain expressly reserved by Pöttinger Landtechnik GmbH.

Refer to PÖTPRO for additional information about your machine:

Are you looking for suitable accessories for your machine? No problem! All the information you require is here at your disposal.

Scan the QR code on the machine's type plate or look under

www.poettinger.at/poetpro

And if we don't have what your looking for, then your Specialist Service Centre is there for you with help and advice.

GB-0600 Docum D Synkro

- 3 -

PÖTTINGER Landtechnik GmbH

Industriegelände 1

4710 Grieskirchen, Austria

Tel. 07248 / 600 -0

Telefax 07248 / 600-2511

❑

Machine checked according to delivery note

.

Check that delivery is complete. All safety-relevant equipment and

operating facilities are available.

❑

Operation, commissioning and maintenance of the machine or the implement have been discussed and explained

with the customer according to the operating instructions.

❑

Adaption to tractor completed

❑

Transport and working positions explained.

❑

Information provided on optional and additional equipment.

❑

Instruction given on the necessity of reading these Operating Instructions.

Please place a cross where appropriate.

X

Please verify the listed items in accordance with the product liability obligation

Confirmation is required to prove that the machine and the operating instructions have been properly handed over. For this purpose you have

received a confirmation e-mail from Pöttinger. If you have not received this mail, please contact your local dealer. Your deale

r can fill in the

handover declaration online.

INSTRUCTIONS FOR PRODUCT HANDOVER

EN

- 4 -

EN

1800_EN-Inhalt_9771

contents

Table of contents

C

O

N

T

EN

T

S

Introduction

................................................................

5

S

YM

BO

LS USE

D

CE mark

.....................................................................

6

Safety hints:

...............................................................

6

WA

R

NING SIGNS

Position of the warning signs

.....................................

7

ATT

ACHING

ATTACHING ATT

TO

TR

AC

TOR

Preparing the tractor

..................................................

8

Using additional implements

......................................

8

Attaching to tractor

.....................................................

9

Travelling on public roads

..........................................

9

Minimising the transport width

..................................

9

OP

E

R

A

T

ATA

I

O

N

Settings for operation

...............................................

10

Setting the depth

......................................................

10

Adjust cutter position (A)

..........................................

10

Set edge plate

...........................................................

11

Adjust harrow

............................................................

11

Working on slopes

...................................................

12

M

UL

T

ULTUL

ILINE

Multiline (optional)

....................................................

13

Raising the implement

.............................................

15

Height adjustment of blade rail

................................

15

Operation with Multiline:

..........................................

16

Attaching to tractor

....................................................

17

Removing from tractor

..............................................

17

Brake Setting Multiline

.............................................

18

Multiline 3001, 3501 hydraulic plan

..........................

19

Multiline 4001 hydraulic plan

....................................

20

H

A

RROW

B

A

R

Overview

..................................................................

21

Harrow bar (only for mounted machines)

.................

21

G

ENE

R

AL MAIN

T

ENANCE

Safety advice

...........................................................

23

General maintenance information

............................

23

Cleaning of machine parts

.......................................

23

Parking in the open

..................................................

23

Winter storage

..........................................................

23

Articulated shafts

.....................................................

24

Hydraulic unit

...........................................................

24

Lubrication points

.....................................................

25

T

ECHNICAL

D

A

T

ATA

A

TAT

Type plate

................................................................

26

Type plate position

...................................................

26

Defined use of the machine

.....................................

27

Technical data

..........................................................

27

Optional Equipment

.................................................

29

Multiline (optional)

....................................................

30

S

U

PP

LEMEN

T

S

AFE

T

Y A

D

VICE

Combination of tractor and mounted implement

......

36

- 5 -

EN

Introduct

I

IntroductIIntroduct

on

1700_GB-Introduction

Introduction

Dear Customer

These Operating Instructions are intended to allow you

to familiarise yourself with the implement and provide

you with clear information on safe and correct handling,

care and maintenance. Thus please take the time to read

these Instructions.

These Operating Instructions comprise part of the imple

-

ment. They are to be kept at a suitable location and acces

-

sible to staff over the entire service life of the implement.

Instructions based on the national provisions regarding

protection against accidents, road traffic and environmental

protection are also to be applied additionally.

Any persons commissioned with the operation, maintenance

or transport of the implement must read and understand

these Instructions, in particular the safety information, prior

to starting work. Any warranty claims lapse on non-obser

-

vance of these Instructions.

In case you have questions related to this operation manual

or further questions about this implement, please contact

your dealer.

Care and maintenance performed in good time and scru

-

pulously according to the maintenance intervals specified

ensure operational and traffic safety as well as the reliability

of the implement.

Use only the original spare parts and accessories from

Pöttinger or accepted by Pöttinger. For those parts relia

-

bility, safety and suitability for Pöttinger machines can be

assured. Warranty claims lapse if non-approved parts are

used. The use of original parts is also recommended after

the warranty period has expired to maintain the performance

of the implement in the long term.

Product liability legislation obliges the manufacturer and

the authorised dealer to issue Instructions when selling

implements and to instruct customers in the use with refer

-

ence to the safety, operating and maintenance regulations.

Confirmation in the form of a declaration of transfer is

required to verify that the implement and Instructions have

been transferred correctly. The declaration of transfer was

attached to the implement on delivery.

Every self-employed person and farmer is an entrepreneur

within the meaning of the product liability legislation. In

accordance with the laws of product liability, entrepre

-

neurial property damages are excluded from the liability.

All damage to property within the meaning of the product

liability legislation is regarded as damage caused by the

implement but not to the implement.

These Operating Instructions are integral part of the imple

-

ment delivery scope. You should therefore hand them over to

the new owner if ownership of the implement is transferred.

Train and instruct the new owner in the regulations stated.

The Pöttinger Service-Team wishes you good luck.

- 6 -

1801_EN-Sicherheit ANSI

EN

s

ymbols used

CE mark

The CE mark, which is affixed by the manufacturer, indicates outwardly that this machine conforms to the engineering

guideline regulations and the other relevant EU guidelines.

EU

Declaration of

C

onformity (see

A

ttachment)

By signing the EU Declaration of Conformity, the manufacturer declares that the machine that

is brought into service complies with all relevant fundamental safety and health requirements.

Safety hints:

These Operating

I

nstructions contain the

following

F

igures:

D

ANGE

R

I

f you do not follow the instructions in a text section

with this marking, there is a risk

of fatal or life-

threatening injury.

•

All instructions in such text sections must be

followed!

W

A

WA W

R

NING

I

f you do not observe the instructions marked this

way, there is the risk of a severe injury.

•

All instructions in such text sections must be

followed!

CAU

T

I

O

N

I

f you do not observe the instructions marked this

way, there is the risk of an injury.

•

All instructions in such text sections must be

followed!

N

OT

E

I

f you do not observe the instructions marked this

way, there is the risk of material damage.

•

All instructions in such text sections must be

followed!

T

I

P

The text sections marked in this way provide you with

special recommendations and advise regarding the

economical use of the implement.

ENVI

RO

NMEN

T

The text sections marked in this way provide practices

and advice on environmental protection.

The features marked as (optional) are only available as

standard with specific implement versions or are only

offered for specific versions as optional equipment or are

only offered in certain countries.

Figures may deviate from your implement in detail and are

to be taken as illustrations of operating principle.

Designations such as right and left always apply as the

direction of travel unless the text or illustrations clearly

show otherwise.

- 7 -

EN

1800_GB-Warning signs_9771

Warning signs

N

o.

Warning signs

M

eaning

N

o.

Warning signs

M

eaning

1

Read the machine's

operating instructions

carefully before initial

startup.

3

Never reach into the

crushing danger area

as long as parts can

move there.

2

bsb 447 410

Danger due to ejected

components

-

Keep a safe

distance

4

Do not stand in the

swivel range of the

machines.

Position of the warning signs

049-17-14

22

3

4

- 8 -

1800-EN Attaching_9771

EN

a

ttaching to tractor

L

ifting gear

-

The left and right lifting struts (4) must be the same

length.

Adjust using adjusting device (3).

If the lifting struts (4) can be pinned at various points on the

lower link, then select the rear point (H). In doing this,

the tractor’s hydraulics will not be so greatly overloaded.

-

Pin (2) upper link (1) in accordance with the

manufacturer’s specifications.

S

etting-up for transportation

-

Secure lower links with struts (5) so that attached

machine cannot swing out during transportation.

-

The operating lever for the hydraulics must be secured

against lowering.

M

ounting axle

The mounting axle on the attachment must be selected

depending on the connection size (category II or III) on

the tractor's lifting unit. See Spare Parts List also.

Using additional implements

Mount additional devices, such as the drill box (DB),

on the machine in accordance with the manufacturer's

instructions.

•

 Do

not

overload

the

TERRADISC.

If

in

doubt

contact

our customer service office.

•

 In

addition,

observe

the

power

range

limits

of

the

tractor

in use.

Preparing the tractor

Wheels

-

Air pressure in the tractor's rear tyres should be 0.8 bar

during operation.

-

Under heavy working conditions additional wheel weights

can be advantageous. See the tractor manufacturer's

operating manual also.

Ballast weights

The tractor must have sufficient ballast at the front in

order to guarantee steering and braking capabilities.

D

ANGE

R

L

ife hazard or material hazard - due to wrong tractor

ballast distribution.

•

The front axle of the tractor must always be

loaded with at least 20% of the tractor's tare

weight to guarantee the steering and braking

capacity of the tractor/trailer unit.

20%

Kg

H

ydraulic control on the lifting gear (position

control)

For attaching and unattaching the machine, and for

road transport.

The position control is the normal setting for the lifting

gear hydraulics.

The attached machine remains at the height (= position)

set by the servo (ST).

- 9 -

1800-EN Attaching_9771

EN

Att

A

AttAAtt

ching to tr

A

ching to trAching to tr

ctor

Attaching to tractor

W

A

WA W

R

NING

Risk of serious injury through crushing when coupling

the machine to the lower linkage.

•

When coupling to the lower linkage, take

particular care not to become wedged or

caught in between.

-

Switch tractor’s hydraulics to position control.

-

Attach implement to lower link and secure with linch

pin.

Position upper link (1)

-

Position upper link (1) so that the attachment point (P1)

on the machine is somewhat higher than the attachment

point (P2) on the tractor, even during operation.

Travelling on public roads

•

 Observe

the

statutory

requirements

of

the

country/state

you are in.

•

 Parts

and

attachment

-

See spare parts list

M

achine's transport width

TERRADISC 3001 = 3 m

TERRADISC 3501 = 3.5 m

TERRADISC 4001 = 4.0 m

C

ertificate of

E

xemption

•

 The

machine's

transport

width

is

more

than

3

m

and

to

reduce the width is technically impossible.

Therefore, to travel on public roads it is necessary to

obtain a Certificate of Exemption from the authorities

responsible.

• Safety

advice:

See

Supplement

A1:

Points

1,

3,

4

and

6-9.

Minimising the transport width

1.

I

nserting the edge plate on the right side

-

Remove pins from their current positions

-

Insert edge plate

-

Insert pin in P1 and secure

P1

2.

H

ydraulically raise the outer discs on both

sides

1.

Using the rope in the tractor cabin, change the

hydraulics from "Working depth" to "Raise the Outer

Discs"

2.

Using the tractor's hydraulics raise the outer discs

on both sides.

The edge plate on the left side is folded up as well.

T

I

P

Stabling, cleaning and wintering the implement

Please observe the advice in the chapter MAINTENANCE!

- 10 -

1800-GB Settings_9771

EN

o

P

eration

Settings for operation

S

tarting work

1.

Check for correct attachment.

Before initial operation check all screws for tightness

and retighten if necessary.

2.

The machine should be horizontally attached to the

tractor. It should not dip to one side.

From the longitudinal view, the frame should be parallel

to the field service.

3.

Fix the lower link (4) so that the machine cannot swing

out.

Setting the depth

W

A

WA W

R

NING

Risk of serious injury exists through crushing when

setting the depth stops.

•

Ensure that no-one is able to unintentionally

operate the tractor's hydraulics:

•

Turn the tractor off and remove the key.

•

Disconnect the hydraulic cable.

S

et required working depth

The working depth is set via the number of depth stops

and actuated by the hydraulic cylinder.

T

I

P

Always make the settings the same on both sides.

Adjust cutter position (A)

-

Swivel the left and right levers accordingly (A1)

-

Insert the pins in the same holes on the left and right

arm.

- 11 -

1800-GB Settings_9771

EN

OPERATION

Set edge plate

Purpose: There should be no soil thrown out to the side

(ridging)

S

etting possibilities:

1. Lateral distance to the machine:

P1

-

Remove pins from P1

-

Adapt edge plate

-

Insert pins and secure

2.

Edge plate height

P2

P3

Set the edge plate so that no ridging can occur.

Insert pin (P3) in the hole pattern at the required height

and secure with linch pin.

Top position: Top front hole (P2)

Lowest position, Lowest rear hole (P3)

3. Edge plate angle

P4

Set the edge plate so that the bottom of the edge plate

sits flush with the ground.

-

Loosen the screw (P4) and with that the U-bolt

-

Change the edge plate angle

-

Retighten the screws

N

OT

E

Property damage through falling machine parts.

•

Regularly check the tightness of the screw

joints

T

I

P

Always carry out the adjustment similarly on both sides.

Adjust harrow

5

5a

-

Working depth with bolt "5"

-

Inclination angle with bolt "5a"

T

I

P

Always carry out the adjustment similarly on both sides.

- 12 -

1800-GB Settings_9771

EN

OPERATION

Working on slopes

D

ANGE

R

L

ife-threatening danger exists through the tractor/

trailer tipping on an incline, especially in transport

position and when cornering.

•

Travel horizontally along the contours when

working on slopes.

•

Reduce general speed relative to the cir

-

cumstances and especially when cornering.

•

It is safer to drive backwards on a slope

than to carry out a risky turning manoeuvre.

The weight of the machine influences the tractor's handling

characteristics.

Danger of tipping exists when the permissible lateral

inclination is exceeded.

- 13 -

1900-EN MULTILINE_9771

EN

m

ultiline

Multiline (optional)

1.

S

ize:

-

Drawbar (1)

-

Chassis with tyre packer roller (2)

-

Seed drill (3) hoist

1

2

3

2.

C

ontrol:

The Multiline hoist control functions through a double-

acting control unit

3.

Transport position

N

OT

E

Risk of property damage to axles and frame sections

during transport through exceeding the maximum

permissible axle load.

•

Empty the seed drill seed box before trans

-

porting it on public roads.

1.

Raise the disc harrow and seed drill using the control

unit

2.

Close the stop cocks on the drawbar.

3.

Push the blade rail inwards on both sides by one

hole position to avoid exceeding the legal transport

width.

4.

Adjust the tractor's lower link so that the two tyre

packer roller axles are equally loaded when braking.

Reference value: ~700 mm (ground to centre pin)

4.

Working position:

1.

Open upper stopcock.

The upper stop cock locks the lifting function of the

disc harrow.

2.

Pull the cord to switch to side discs folding

3.

Lower side discs using the control unit

4.

Open lower stopcock

The lower stop cock locks the lifting function of the

seed drill.

5.

Select required working depth

6.

Align implement using hoist and machine's

perpendicular

- 14 -

1900-EN MULTILINE_9771

Multiline

EN

5.

U

nhitch the seed drill (

S

olo trip with the disc

harrow)

1.

Raise the seed drill using the control unit

2.

Close the upper seed drill stopcock

3.

Reset working depth on both sides to 0

4.

Place rear parking supports underneath on both

sides and secure

5.

Lower the seed drill using the control unit and place

it gently on the rear parking supports.

6.

Remove upper link (1) between seed drill and Multiline

chassis

1

7.

Disconnect all cables and lines between the seed

drill and the soil-tilling machine

8.

Raise the soil-tilling machine so that the front supports

can be pushed in

9.

Position and secure the front parking supports on

both sides.

10.

Open and lock the connecting bracket (2) between

seed drill and disc harrow on both sides. The

connection brackets are located on the outer side

of the machine.

2

11.

Completely lower the chassis using the control unit.

12.

Move off with the harrow disc under the seed drill.

6.

A

ttaching the seed drill: in chronologically

reversed order

7.

M

aintenance:

a.

L

ubrication

8x tyre packer roller (1) storage (unbraked)

1

4x tyre packer roller storage (braked)

1

3x per Multiline-chassis lifting cylinder (2)

2

- 15 -

1900-EN MULTILINE_9771

Multiline

EN

2x Multiline-chassis linkage (3)

3

b.

Calibration of the master-slave cylinder combination for

raising the seed drill

1.

Release calibration lever (10) - position completely

out

10

2.

Raise the seed drill completely using the control unit

– cylinders at limit stop (the seed drill may "lurch")

3.

Latch calibration lever (10) - position completely in

4.

Lower the seed drill again using the control unit

c.

Tyre packer roller tyre pressure (= chassis Multiline):

4.0 bar

Raising the implement

The unit can be hoisted by a lifting jack, from point (1) only,

as illustrated. This point is located on the trailer on the left

side and the right side of the implement.

1

D

ANGE

R

Danger to life - by tilting the device!

•

Change tyres in the working position using

a jack.

Height adjustment of blade rail

The blade rail serves to level the soil between the tyres

of the tyre packer.

The lower the blades are set, the more pressure is applied

to the blade rail.

L

ocking the blade rail:

In difficult operating conditions (heavy soil, wet) it is also

possible to drive without the blade rail.

1.

Lift the blade rail out

2.

Close the pictured hydraulic stopcock (11) to lock the

blade rail in the raised position. The hydraulic stopcock

is located on the Multiline chassis, in the direction of

travel, on the left in front of the tyre packer roller.

11

- 16 -

1900-EN MULTILINE_9771

Multiline

EN

Operation with multiline:

Position pin (1) at the top.

1

Procedure:

• Place

the

seed

drill

on

the

rear

supports

so

that

the

pin (1) is relieved.

• Release

and

remove

(1)

• Set

seed

drill

height

on

the

hole

pattern

• Place

(1)

in

corresponding

hole

and

secure

• Remove

seed

drill

rear

supports

- 17 -

1900-EN MULTILINE_9771

Multiline

EN

Attaching to tractor

W

A

WA W

R

NING

Risk of serious injury by crushing when coupling the

machine to the lower linkage.

•

When coupling to the lower linkage, take

particular care not to become wedged or

caught in between.

1.

Fix tractor lower linkage centrally. Fix hydraulic lower

linkage (U) so that the machine cannot swing to the

side.

2.

Switch tractor hydraulics to position control

3.

Attach machine to the lower linkage

4.

Secure coupling pin (1) correctly

5.

Coupling the hydraulic hoses

• Double-acting

control

devices

• Connect

pressure

line

(3)

and

return

line

(4)

3

4

6.

Connecting the electric cables

7.

Raise support stand (5) to transport position

1

5

6

8.

Secure with linchpin (6).

Removing from tractor

D

ANGE

R

Risk of death - in the event of unpredictable

movements of tractor or machine

•

Park the machine only on ﬁrm, level ground.

•

Secure the tractor against unintentional

rolling.

•

Turn the engine off.

•

Remove the key.

•

Secure the machine against tipping using

supports.

1.

Secure the machine with chocks.

2.

Extend support stand (5) and fix it with pins (6)

3.

Disconnect hydraulic lines and electric cables

4.

Uncouple machine from tractor hydraulics

5.

Attach the anti-theft device (7) on the left and right of

the drawbar

7

6.

Secure anti-theft device (7) with padlock

7

- 18 -

1900-EN MULTILINE_9771

Multiline

EN

Brake Setting Multiline

The brake must be matched to the total weight of the

combined machines.

As brakes are components of the machine that are relevant

to safety, this setting must be done in a certified specialist

workshop. If you do not comply with this requirement,

Pöttinger will not be held responsible for the consequences

of this contravention.

1.

I

nstructions for the certified specialist

workshop:

1.1

S

etting the pressure limits:

3

4

1

2

1.

Weigh the combined machines on calibrated scales.

2.

Refer to Table 1.3 for the pressure values for the

measured axle load of the combined machine

3.

Connect calibrated pressure gauge to the valve (1).

4.

Loosen the bolt for the lower pressure limit (3) (MIN)

and set it so that the lower pressure limit corresponds

to the table value for the machine weight. Tighten

the bolt for the lower pressure limit (3).

5.

Loosen the bolt for the upper pressure limit (2) (MAX)

and set it so that the upper pressure limit corresponds

to the table value for the machine weight. Tighten

the bolt for the upper pressure limit.

6.

Remove pressure gauge from the valve (1)

1.2

C

hanging the basic setting of the brake

pressure:

If the desired settings cannot be reached within the console,

it is possible to set the basic setting of the brake pressure.

1.

Remove the bolts (4).

2.

Use an Allen key to turn the position of the shaft so

that the desired pressure value is within the setting

console.

3.

Tighten bolt (4).

1.3 Relationship brake pressure – axle load of

the combined machine:

The values stated in the table refer only to the empty or

loaded state. No partly loaded states are calculated!

Axle

load in

kg

Brake cylinder

- pressure at

pm = 6 bar

Control

action i

p on ALB =

6.5 bar

p off ALB in

bar

900

41.8

2.30

3.0

1150

50.9

1.85

3.6

1400

61.8

1.50

4.3

1650

73.2

1.25

5.1

2000

78.6

1.16

5.4

- 19 -

1900-EN MULTILINE_9771

Multiline

EN

multiline 3001, 3501 hydraulic plan

Key:

1

Side disc folding mechanism

2

Depth adjustment

3

Blade holder

4

Lifting arms

A

B

C

1

D

1

B

1

A

1

A

1

B

1

D

1

C

1

S

P

1

M

B

1

A

B

0

,

1

6

l

5

0

b

a

r

4

2

.

8

0

1

4

2

.

8

0

1

A

B

A

D

W

4

2

.

7

9

1

4

2

.

7

9

1

4

5

.

6

2

5

4

5

.

6

2

4

0

,

8

m

0

,

8

m

0

,

8

m

0

,

8

m

4

8

.

0

9

5

4

2

.

8

2

0

4

2

.

8

2

1

0

,

5

m

4

2

.

8

1

9

4

2

.

8

1

9

4

5

.

1

.

0

6

4

5

.

1

.

0

2

4

5

.

1

.

0

6

2

1

3

4

- 20 -

1900-EN MULTILINE_9771

Multiline

EN

multiline 4001 hydraulic plan

Key:

1

Side disc folding mechanism

2

Depth adjustment

3

Blade holder

4

Lifting arms

A

B

C

1

D

1

B

1

A

1

A

1

B

1

D

1

C

1

S

P

1

M

B

1

A

B

0

,

1

6

l

5

0

b

a

r

4

2

.

8

0

1

B

A

D

W

4

5

.

6

2

5

4

5

.

6

2

4

0

,

8

m

4

8

.

0

9

5

4

2

.

8

2

0

4

2

.

8

2

1

0

,

5

m

4

5

.

1

.

0

6

4

5

.

1

.

0

2

4

2

.

8

0

1

A

B

4

2

.

7

9

1

0

,

8

m

0

,

8

m

0

,

8

m

4

2

.

7

9

1

4

2

.

8

1

9

4

2

.

8

1

9

0

,

8

m

4

2

.

7

9

1

4

5

.

1

.

0

6

1

2

3

4

La pagina sta caricando ...

Pottinger TERRADISC 4001 Istruzioni per l'uso

Questo manuale è adatto anche per

Pottinger TERRADISC 4001 Istruzioni per l'uso

in altre lingue

Documenti correlati

Altri documenti