Peerless DS-S555-4X3 Guida d'installazione

12015-06-24 #:009-9117-4 (2018-03-08)

ENG

DS-S555-4X3

46" - 55"

(117 - 140 cm)

1200 lb

(544 kg)

MAX

22015-06-24 #:009-9117-4 (2018-03-08)

Symbols

ENG

WARNING

ENG

x3

Screws must get at

least three full turns

and t snug.

ENG

Do not overtighten screws.

ENG

Display center.

ENG

ENG - Do not begin to install product until you have read and understood the instructions and warnings

contained in this user guide. Always use an assistant or mechanical lifting equipment to safely lift and position

equipment. This product must be installed onto at, hard, level surface to prevent tipping. Use with heavier

displays may result in instability causing tip over resulting in death or serious injury. Displays must be removed

before moving cart. Not recommended for use in areas with heavy trafc. This product is intended for indoor use

only. Use of this product outdoors could lead to product failure or personal injury. Screws must be tightly secured.

Do not overtighten screws or damage can occur and product may fail. Never exceed the Maximum Load

Capacity. Be careful not to pinch ngers when operating the mount. Death or serious injury may occur when

children climb on audio and/or video equipment furniture. A remote control or toys placed on the furnishing may

encourage a child to climb on the furnishing and as a result the furnishing may tip over on to the child. Relocating

audio and/or video equipment to furniture not specically designed to support audio and/or video equipment may

result in death or serious injury due to the furnishing collapsing or over turning onto a child. For support please

call customer care at 1-800-865-2112.

WARNING

32015-06-24 #:009-9117-4 (2018-03-08)

Tools Needed for Assembly.

ENG

3/8"

(10mm)

3/8"

(10mm)

To properly tighten screws: Tighten until screw

head makes contact, then tighten another 1/2

turn. Do not overtighten screws.

1

2

+1/2

4

3

42015-06-24 #:009-9117-4 (2018-03-08)

Parts (Before beginning, make sure you have all parts shown below).

Parts List

Part #Description Qty

Apedestal 3 146-T1132

Bcolumn 3 146-T1131

Cextension 3145-T1778

Dcover 3 145-T1809

Eside support bracket 4 145-T1807

Fvertical support bracket 6 145-T1806

Gleft adaptor bracket 12 146-1609

Hright adaptor bracket 12 146-1608

Icomputer cover 1 145-T1930

Jcomputer shelf 1 145-T1931

Kdual cross support 6 146-T1905

Lextension adaptor 3145-T1935

Mcord bracket 6 146-T1321

Nbracket, 4x2 conguration 3145-T1858

Oknob 6 560-1160

PM8 x 16mm socket button screw 140 520-9527

QM8 square nut 56 530-1066

Rcover clip 12 590-0317

SM5 x 10mm type-f, socket pin screw 26 520-1164

T1/4" power bit 1 560-0263

Ubar nut 6 146-1319

V5mm allen wrench 1 560-9640

Wnylon shoulder washer 48 590-2233

XM6 x 12mm socket pin screw 48 520-1050

Y4mm allen wrench 1 560-9646

ZM6 x 35mm screw 12 520-0717

AA rawl bolt #6913 12 5M9-381-H03

D (3)

cover

B (3)

column

F (6)

vertical support

bracket

E (4)

side support

bracket

A (3)

pedestal

C (3)

extension

H (12)

right adaptor

bracket

G (12)

left adaptor

bracket

52015-06-24 #:009-9117-4 (2018-03-08)

I (1)

computer cover

J (1)

computer shelf

N (3)

bracket, 4x2

conguration

K (6)

dual cross

support

Y (1)

4mm allen

wrench

P (140)

M8 x 16mm

Q (56)

M8 square

nut

R (12)

cover clip

S (26)

M5 x 10mm T (1)

1/4" power

bit

V (1)

5mm allen

wrench

W (48)

nylon shoulder

washer

X (48)

M6 x 12mm

L (3)

extension

adaptor

rawl bolt

AA (12)

M6 x 35mm

Z (12)

M (6)

cord

bracket

O (6)

knob bar nut

U (6)

62015-06-24 #:009-9117-4 (2018-03-08)

Z (4)

AB

2-1

Do not fully tighten hardware

P (4)

U (2)

L

TOP VIEW

x3

1

x3

V

72015-06-24 #:009-9117-4 (2018-03-08)

2-2

TIGHTEN

CONNECTING

HARDWARE

x3

C

B

V

82015-06-24 #:009-9117-4 (2018-03-08)

3-1

3-2

P (6)

Q (4)

F

x6

1/8"

(3mm)

1/8"

(3mm)

TIGHTEN

CONNECTING

HARDWARE

DISPLAY HEIGHT

x2

V

92015-06-24 #:009-9117-4 (2018-03-08)

4

x2x2

5

M (2)

O (2)

TOP VIEW

MO

TIGHTEN

CONNECTING

HARDWARE

R (4)

D

10 2015-06-24 #:009-9117-4 (2018-03-08)

6-1

Use metric formula below and diagram to

right to determine hole pattern required for

center vertical support bracket.

All dimensions are metric.

Use the outside mounting holes when…

a x 4 > 4368mm and a x 3 + b < 4318mm

Use the inside mounting holes when…

a x 4 > 4098mm and a x 3 + b < 4064mm

P (12)

Q (8)

N

Q (8)

N

P (12)

BACK

SIDE

1/8"

(3mm)

b

a

BACK OF DISPLAY

x3 V

11 2015-06-24 #:009-9117-4 (2018-03-08)

DISPLAY HEIGHT

6-3

6-2

M

O

TOP VIEW

MO

TIGHTEN

CONNECTING

HARDWARE

B

12 2015-06-24 #:009-9117-4 (2018-03-08)

7

ENG - When installing Peerless mounts on a concrete oor, the oor must be at least 8" thick with a minimum

compressive strength of 2000 psi. Never attach concrete expansion anchors to concrete covered with plaster,

drywall, or other nishing material.

WARNING

FRN - Lors de l’installation de supports de plafond Peerless sur un plafond en béton, celui-ci doit avoir au moins

8 po (20 cm) d'épaisseur et une résistance à la compression d'au moins 2 000 psi. Ne xez jamais des chevilles

à expansion pour béton à du béton recouvert d’une couche de plâtre, d’une cloison sèche ou de tout autre

matériau de nition.

ADVERTISSEMENT

ESP - Cuando vaya a instalar soportes de techo de Peerless en techos de concreto, los techos tienen que

tener, por lo menos, 8" de grosor con una resistencia a la compresión de 2000 psi como mínimo. Nunca je los

anclajes de expansión para concreto a supercies de concreto recubiertas con yeso, yeso-cartón u otro material

de acabado.

ADVERTENCIA

DEU - Werden Peerless-Deckenhalter an einer Betondecke angebracht, so muss deren Dicke mindestens 203

mm (8 Zoll) und ihre Druckfestigkeit mindestens 13,8 N/mm2 (2000 psi) betragen. Betonspreizdübel dürfen

auf keinen Fall an Beton befestigt werden, der mit Verputz, Trockenwand- oder anderem Deckschichtmaterial

bedeckt ist.

ACHTUNG

WAARSCHUWING

NEL - Als de Peerless-plafondbevestiging op een betonnen plafond wordt geïnstalleerd, moet dit plafond een

dikte van ten minste 20 cm hebben en een druksterkte van ten minste 2000 psi. Gebruik nooit expansie-ankers

voor beton bij installatie op een betonnen plafond bedekt met gips, gipsplaat of ander afwerkingsmateriaal.

ITL - In sede d’installazione dei sostegni Peerless su un softto in calcestruzzo solido, il softto deve avere

uno spessore minimo di 20 cm, con una resistenza alla compressione di almeno 2000 psi (140 kg/cm2). Non

attaccare mai ancoranti a espansione per calcestruzzo su calcestruzzo ricoperto con intonaco, cartongesso o

altro materiale di nitura.

AVVERTENZA

ČEŠ - Při instalaci stropních držáků Peerless na betonový strop musí být tento trop hrubý minimálně 20 cm s

minimální pevností v tlaku 2000 psi. Expanzní kotvy do betonu nikdy nepřipojujte do betonu pokrytého omítkou,

sádrokartonem nebo jiným dokončovacím materiálem.

VÝSTRAHA

TÜR - Peerless tavan kaidelerini beton duvara monte ettiğinizde, tavan en azından 2000 psi asgari basınç

dayanımına sahip olmalı ve kalınlığı da en azından 8" olmalıdır. Beton dübelleri hiç bir zaman alçı, alçıpan veya

başka bir bitirme materyali ile kaplı betona takmayınız.

UYARI

AVISO

POR - Ao instalar os suportes para o teto Peerless em tetos de betão, o teto deve ter, no mínimo, 203 mm de

espessura e uma força de compressão mínima de 2000 psi. Nunca instale âncoras de expansão para betão em

superfícies cobertas com estuque, gesso ou outros materiais de acabamento.

SLK - Pri montáži stropných držiakov Peerless na betónový strop musí mať tento strop hrúbku minimálne 20 cm

s minimálnou tlakovou pevnosťou 2000 psi. Expanzné kotvy do betónu nikdy nenasadzujte do betónu pokrytého

omietkou, sadrokartónom či iným nalizačným materiálom.

VÝSTRAHA

13 2015-06-24 #:009-9117-4 (2018-03-08)

4

3"

(76mm)

3/8"

(10mm)

7-1

Align base. Mark mounting holes.

ENG

7-2

Drill mounting holes into

supporting surface

(3" (76mm) minimum

depth required).

ENG

3/8"

(10mm)

7-3

Align base. Install using concrete anchors

provided.

ENG

3/8"

(10mm)

55.00"

(1397mm)

55.00"

(1397mm)

ENG Maximum 35 ft • lb (47 N.M.).

AA (12)

55.00"

(1397mm)

55.00"

(1397mm)

14 2015-06-24 #:009-9117-4 (2018-03-08)

8-1

TIGHTEN

CONNECTING

HARDWARE

K (2)

V

15 2015-06-24 #:009-9117-4 (2018-03-08)

8-2

TIGHTEN

CONNECTING

HARDWARE

K (2)

V

16 2015-06-24 #:009-9117-4 (2018-03-08)

8-3

TIGHTEN

CONNECTING

HARDWARE

K (2)

V

17 2015-06-24 #:009-9117-4 (2018-03-08)

TIGHTEN

CONNECTING

HARDWARE

9

E

P (2)

Q (2)

P (8)

Q (8)

E (4)

V

18 2015-06-24 #:009-9117-4 (2018-03-08)

X

10-1

H

G

10-2

Center adapter brackets

vertically on back of screen.

ENG

H

G

x3

W X P

OR

V

x12

x12 Y

19 2015-06-24 #:009-9117-4 (2018-03-08)

11-1

11-2

Must hang displays to bottom row rst; Secure pin

in "locked" position.

Must hang displays on top row last; Secure pin

in "locked" position.

"LOCKED"

POSITION

"LOCKED"

POSITION

20 2015-06-24 #:009-9117-4 (2018-03-08)

11-3

Must hang displays on top row last; Secure pin

in "locked" position.

"LOCKED"

POSITION

11-4

OPTIONAL: Insert M5 x 10mm type-F socket pin screws

(S) to lock latches. Y

S

"LOCKED"

POSITION

x24

La pagina sta caricando ...

Peerless DS-S555-4X3 Guida d'installazione

Peerless DS-S555-4X3 Guida d'installazione

in altre lingue

Documenti correlati

Altri documenti