NEC MultiSync® FP1355 Manuale del proprietario

MultiSync FP1355

User’s Manual

UÏivatelská pﬁíruãka

Bedienerhandbuch

δηγίες ρήσης

Manual del usuario

Manuel Utilisateur

Manuale utente

Gebruikershandleiding

Podr´cznik u˝ytkownika

Руководство пользователя

Kullan∂c

∂ Klavuzu

00Cover_all.p65 22.02.2001, 14:12 Uhr1

00Cover_all.p65 22.02.2001, 14:12 Uhr2

Declaration

Declaration of the Manufacturer

We hereby certify that the colour monitor

MultiSync FP1355 (NSZ2102STTUW) is in

compliance with Council Directive 73/23/EEC:

- EN 60950

Council Directive 89/336/EEC:

- EN 55022

- EN 61000-3-2

- EN 61000-3-3

- EN 55024

and marked with

NEC-Mitsubishi Electric Visual Systems Corporation

4-13-23, Shibaura,

Minato-Ku

Tokyo 108-0023, JAPAN

00Cover_all.p65 22.02.2001, 14:12 Uhr3

TCO’99

Congratulations! You have just purchased a TCO’99

approved and labeled product! Your choice has

provided you with a product developed for

professional use. Your purchase has also contributed

to reducing the burden on the environment and also

to the further development of environmentally

adapted electronics products.

Why do we have environmentally labelled computers?

In many countries, environmental labelling has become an established

method for encouraging the adaptation of goods and services to the

environment. The main problem, as far as computers and other

electronics equipment are concerned, is that environmentally harmful

substances are used both in the products and during the manufacturing.

Since it has not been possible for the majority of electronics equipment

to be recycled in a satisfactory way, most of these potentially damaging

substances sooner or later enter Nature.

There are also other characteristics of a computer, such as energy

consumption levels, that are important from the viewpoints of both the

work (Internal) and natural (external) environments. Since all methods of

conventional electricity generation have a negative effect on the

environment (acidic and climate-influencing emissions, radioactive

waste, etc.), it is vital to conserve energy. Electronics equipment in

offices consume an enormous amount of energy since they are often left

running continuously.

What does labelling involve?

This product meets the requirements for the TCO’99 scheme which

provides for international and environmental labelling of personal

computers. The labelling scheme was developed as a joint effort by the

TCO (The Swedish Confederation of Professional Employees), Svenska

Naturskyddsforeningen (The Swedish Society for Nature Conservation)

and Statens Energimyndighet (The Swedish National Energy

Administration).

00Cover_all.p65 22.02.2001, 14:12 Uhr4

The requirements cover a wide range of issues: environment,

ergonomics, usability, emission of electrical and magnetic fields, energy

consumption and electrical and fire safety.

The environmental demands concern restrictions on the presence and

use of heavy metals, brominated and chlorinated flame retardants, CFCs

(freons) and chlorinated solvents, among other things. The product must

be prepared for recycling and the manufacturer is obliged to have an

environmental plan which must be adhered to in each country where the

company implements its operational policy. The energy requirements

include a demand that the computer and/or display, after a certain period

of inactivity, shall reduce its power consumption to a lower level in one or

more stages. The length of time to reactivate the computer shall be

reasonable for the user.

Labelled products must meet strict environmental demands, for example,

in respect of the reduction of electric and magnetic fields, physical and

visual ergonomics and good usability.

Environmental Requirements

Flame retardants

Flame retardants are present in printed circuit boards, cables, wires,

casings and housings. In turn, they delay the spread of fire. Up to thirty

percent of the plastic in a computer casing can consist of flame retardant

substances. Most flame retardants contain bromine or chloride and these

are related to another group of environmental toxins, PCBs, which are

suspected to give rise to severe health effects, including reproductive

damage in fisheating birds and mammals, due to the bioaccumulative*

processes. Flame retardants have been found in human blood and

researchers fear that disturbances in foetus development may occur.

TCO’ 99 demand requires that plastic components weighing more than

25 grams must not contain flame retardants with organically bound

chlorine and bromine. Flame retardants are allowed in the printed circuit

boards since no substitutes are available.

Lead**

Lead can be found in picture tubes, display screens, solders and

capacitors. Lead damages the nervous system and in higher doses,

causes lead poisoning.

TCO’ 99 requirement permits the inclusion of lead since no replacement

has yet been developed.

00Cover_all.p65 22.02.2001, 14:12 Uhr5

Cadmium**

Cadmium is present in rechargeable batteries and in the

colourgenerating layers of certain computer displays. Cadmium damages

the nervous system and is toxic in high doses.

TCO’ 99 requirement states that batteries, the colourgenerating layers of

display screens and the electrical or electronics components must not

contain any cadmium.

Mercury**

Mercury is sometimes found in batteries, relays and switches, Mercury

damages the nervous system and is toxic in high doses.

TCO’ 99 requirement states that batteries may not contain any Mercury.

It also demands that no mercury is present in any of the electrical or

electronics components associated with the display unit.

CFCs (freons)

CFCs (freons)are sometimes used for washing printed circuit boards.

CFCs break down ozone and thereby damage the ozone layer in the

stratosphere, causing increased reception on Earth of ultraviolet light

with consequent increased risks of skin cancer (malignant melanoma).

The relevant TCO’ 99 requirement; Neither CFCs nor HCFCs may be

used during the manufacturing and assembly of the product or its

packaging.

* Bio-accumulative is defined as substances which accumulate within

living organisms.

** Lead, Cadmium and Mercury are heavy metals which are Bio-

accumulative.

To obtain complete information on the environmental criteria document,

order from:

TCO Development Unit

SE-114 94 Stockholm

SWEDEN

FAX Number: +46 8 782 92 07

E-mail (Internet): development@tco.se

You may also obtain current information on TCO’ 99 approved and

labelled products by visiting their website at:

http://www.tco-info.com/

00Cover_all.p65 22.02.2001, 14:12 Uhr6

English

âesky

Deutsch

Ελληνικά

Español

Français

Italiano

Nederlands

Polski

Русский

Türkçe

01b_XChapterOpener 22.02.2001, 14:12 Uhr1

01b_XChapterOpener 22.02.2001, 14:12 Uhr2

English-1

English

Contents

Your new MultiSync FP1355 monitor box* should contain the following:

• MultiSync FP1355 Monitor with tilt/swivel base

• Power cord

• Video Signal Cable (VGA - DVI-A)

• User’s Manual

• USB cable

• CD-ROM:

Includes complete User’s Manual in PDF format and Windows related

files (INF file and colour profile). To see the complete User’s Manual,

Acrobat Reader 4.0 must be installed at your PC.

* Remember to save your original box and packing material to transport

or ship the monitor.

Power Cord

Video Signal Cable

User’s Manual

CD-ROM

USB cable

01b_english 22.02.2001, 14:12 Uhr1

English-2

Quick Start

To attach the MultiSync FP1355 monitor to your system, follow these

instructions:

1. Turn off the power to your computer.

2. If necessary, install the display card into your system. For more

information, refer to the display card manual.

3. For the PC or Mac with DVI Analog output: Connect the DVI end of

the VGA to DVI-A signal cable to the connector of the display card in

your system (Figure A.1). Tighten all screws.

For the PC with VGA Analog output: Connect the VGA end of the

VGA to DVI-A signal cable to the connector of the display card in your

system (Figure A.2).

For the Mac: Connect the MultiSync Macintosh cable adapter (not

included) to the computer (Figure B.1). Attach the VGA end of the

VGA to DVI-A signal cable to the Macintosh cable adapter

(Figure B.1).

NOTE: Some Macintosh systems do not require a Macintosh

cable adapter.

Figure A.1

Figure A.2

01b_english 22.02.2001, 14:12 Uhr2

English-3

English

4. Connect the other end of signal cable connector on the back of the

monitor.

NOTE: Incorrect cable connections may result in irregular

operation, damage display quality/components of CRT

monitor.

5. The Windows

®

95/98/2000 INF file for your MultiSync monitor can be

found on the CD-ROM, delivered with the monitor.

6. Connect one end of the power cord to the AC inlet on the back of the

monitor and the other end to the power outlet (Figure C.1).

7. Turn on the monitor (Figure D.1).

8. Turn on the Computer.

NOTE: If you have any problems, please refer to the

Troubleshooting section of this User’s Manual.

Figure B.1

15-pin mini D-SUB

Video Signal Cable

Computer Mac Adapter

(not included)

Figure C.1

A.1

Power Outlet

Power Cord

Figure D.1

Power Button

01b_english 22.02.2001, 14:12 Uhr3

English-4

Controls

OSM (On-Screen Manager) control buttons on the front of the monitor

function as follows:

To change DVI/D-SUB signal input, press the RESET button.

NOTE: OSM must be closed in order to change DVI/D-SUB signal

input.

NOTE: When RESET is pressed in the main and sub-menu, a

warning window will appear allowing you to cancel the reset

function.

When OSM controls are activated, icons are displayed at the top of the

menu. If an arrow (→) is displayed in a sub-menu, it indicates further

choices are available. To enter a sub-menu, press PROCEED.

Brightness/Contrast Controls

Brightness: Adjusts the overall image and background screen

brightness.

Contrast: Adjusts the image brightness in relation to the background.

Sub-Menu

Exits to the OSM main menu.

Moves the highlighted area

up/down to select one of the

controls.

Moves the bar in the - or +

direction to decrease or

increase the adjustment.

Only executes control or

enters sub-menu.

Resets the highlighted control

to the factory setting.

EXIT

CONTROL ▲/▼

CONTROL -/+

PROCEED

D-SUB/DVI-A

RESET

Main Menu

Exits the OSM menu.

Moves the highlighted

area up/down to select

one of the controls.

Moves highlighted area

left/right to select one of

the controls.

Has no function.

Without OSM menu

screen, push to select the

signal input connector,

D-SUB or DVI-A.

Resets all the controls

within the highlighted

menu to the factory

setting.

01b_english 22.02.2001, 14:12 Uhr4

English-5

English

Degauss: Eliminates the build-up of stray magnetic fields which alter the

correct scan of the electron beams and affect the purity of the screen

colours, focus, and convergence. When activated, your screen image will

jump and waver a bit as the screen is demagnetised.

Caution: Please allow a minimum of 20 minutes to elapse between

uses of the Degauss function.

Size and Position Controls

AutoAdjust: Automatically adjust the horizontal and vertical size and

position settings for applicable timings.

Left/Right: Moves the image horizontally (left or right).

Down/Up: Moves the image vertically (up or down).

Narrow/Wide: Decreases or increases the horizontal size of the image.

Short/Tall: Decreases or increases the vertical size of the image.

Colour Control/Colour Control System

Colour presets 1 through 5 selects the desired colour setting. The bar is

replaced by the colour setting choice from 1 to 5. Each colour setting is

adjusted at the factory to the stated Kelvin. If a setting is adjusted, the

name of the setting will change from Kelvin to Custom.

Red, Green, Blue: Colour Control System decreases or increases the

monitor’s red, green or blue colour guns depending upon which is

selected. The change in colour will appear on screen and the direction

(decrease or increase) will be shown by the bars.

sRGB Mode: sRGB mode provides the suitable colour managed picture

image. You can not change Red, Green and Blue colours individually.

NOTE: In this mode, Brightness and Contrast are not adjustable.

Geometry Controls

Geometry Controls Menu

The Geometry controls allow you to adjust the curvature or angle of the

sides of your display.

Sides In/Out (pincushion): Decreases or increases the curvature of the

sides either inward or outward.

01b_english 22.02.2001, 14:12 Uhr5

English-6

Sides Left/Right (pincushion balance): Decreases or increases the

curvature of the sides either to the left or right.

Sides Tilt (parallelogram): Decreases or increases the tilt of the sides

either to the left or right.

Sides Align (trapezoidal): Decreases or increases the bottom of the

screen to be the same as the top.

Rotate (raster rotation): Rotates the entire display clockwise or

counterclockwise.

Tools 1

Moiré Canceler: Moiré is a wavy pattern which can sometimes appear

on the screen. The pattern is repetitive and superimposed as rippled

images. When running certain applications, the wavy pattern is more

evident than in others. To reduce moiré, adjust the level by using

-/+ control buttons.

Basic Convergence: Aligns all three colours (R,G,B) to form a single

colour (white). The purpose of this control is to ensure that a white line

drawn on the screen is as crisp and clear as possible.

• Use the Horizontal control to adjust the alignment of the white lines in

the up/down direction.

• Use the Vertical control to adjust the alignment of the white lines in

the left/ right direction.

Corner Correction:Allows you to adjust the geometry of the corners of

your display – Top, Top Balance, Bottom or Bottom Balance.

Linearity: This selection allows you to adjust the spacing of the area on

the screen. The purpose of this control is to ensure that a one-inch circle

is a true one-inch circle wherever it is on the screen. The best way to

determine the vertical linearity is as follows:

• Draw equally spaced horizontal lines using a drawing application that

has a ruler.

• Use the Vertical Balance control to adjust the lines near the top and

bottom of your screen.

• Use the Vertical control to adjust the spacing between the lines near

the center and top of your screen.

01b_english 22.02.2001, 14:12 Uhr6

English-7

English

GlobalSync Control: Eliminates picture impurities that may result from

the earth’s magnetic field. While in the sub-menus (GLOBALSYNC, TOP

LEFT, TOP RIGHT, BOTTOM LEFT or BOTTOM RIGHT), use the –/+

control buttons to fine tune the GlobalSync corrections.

Note: NEC recommends that you perform GlobalSync correction

while running a typical application such as a spreadsheet or

text document.

Factory Preset: Selecting Factory Preset allows you a reset most OSM

control settings back to the factory settings. A warning statement will

appear to confirm that you do want to reset ALL settings. Individual

settings can be reset by high-lighting the control to be reset and pressing

the RESET button.

Tools 2

Language: OSM controls menus are available in six languages.

OSM Position: You can choose where you would like the OSM controls

menu to appear on your screen. Selecting OSM Position allows you to

manually adjust the OSM controls menu left, right, up or down.

OSM Turn Off: The OSM controls menu will stay on as long as it is in

use. In the OSM Turn Off sub-menu, you can select how long the

monitor waits after the last touch of a button for the OSM controls menu

to disappear. The preset choices are 10, 20, 30, 45, 60 and 120

seconds.

OSM Lock Out: This control completely locks out access to all OSM

controls functions except Brightness and Contrast. When attempting to

activate OSM controls while in the lock out mode, a screen will appear

indicating that OSM controls are locked out. To activate the OSM Lock

Out function, press PROCEED, then press ▲ and hold down

simultaneously. To deactivate the OSM Lock Out, press PROCEED, then

press ▲ and hold down simultaneously.

IPM System Off Mode:

Enable: The IPM System works normally and all stages of energy

savings are utilized.

Disable: The Off Mode of the IPM System is not used.

NOTE: For standard systems and graphics boards, keep the factory

setting at ENABLE.

01b_english 22.02.2001, 14:12 Uhr7

English-8

EdgeLock Control: Operating your monitor at a non-standard timing

may cause images to appear darker than normal or have colour

distortion. Use of the EdgeLock control will adjust images to their normal

state.

Information

Display Mode: Indicates the current mode and frequency setting of the

monitor.

Monitor Info: Indicates the model and serial numbers of your monitor.

Refresh Notifier: A message will advise you if the refresh rate of the

signal being applied to the monitor by the computer is too low. For further

information, please refer to your display card or system manual.

01b_english 22.02.2001, 14:12 Uhr8

English-9

English

Recommended use

Safety Precautions and Maintenance:

FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE

FOLLOWING WHEN SETTING UP AND USING THE

MULTISYNC FP1355 COLOUR MONITOR:

• DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and

opening or removing covers may expose you to dangerous shock hazards or

other risks. Refer all servicing to qualified service personnel.

• Do not spill any liquids into the cabinet or use your monitor near water.

• Do not insert objects of any kind into the cabinet slots, as they may touch danger-

ous voltage points, which can be harmful or fatal or may cause electric shock, fire

or equipment failure.

• Do not place any heavy objects on the power cord. Damage to the cord may

cause shock or fire.

• Do not place this product on a sloping or unstable cart, stand or table, as the

monitor may fall, causing serious damage to the monitor.

• Keep the monitor away from high capacity transformers, electric motors and other

devices such as external speakers or fans, which may create strong magnetic

fields.

• If possible, position the monitor so that it is facing the east to minimize the effects

of the earth’s magnetic field.

• Changing the direction of the monitor while it is powered on may cause image

discolouration. To correct this, turn the monitor off for 20 minutes before powering

it back on.

• When operating the MultiSync FP1355 with its AC 220-240V worldwide power

supply, use a power supply cord that matches the power supply voltage of the AC

power outlet being used. The power supply cord you use must have been ap-

proved by and comply with the safety standards of your country. (Type H05VV-F

should be used except in UK)

• In UK, use a BS-approved power cord with molded plug having a black (5A) fuse

installed for use with this monitor. If a power cord is not supplied with this monitor,

please contact your supplier.

Immediately unplug your monitor from the wall outlet and refer servicing to qualified

service personnel under the following conditions:

• When the power supply cord or plug is damaged.

• If liquid has been spilled, or objects have fallen into the monitor.

• If the monitor has been exposed to rain or water.

• If the monitor has been dropped or the cabinet damaged.

• If the monitor does not operate normally by following operating instructions.

01b_english 22.02.2001, 14:12 Uhr9

English-10

• Allow adequate ventilation around the monitor so that heat can

properly dissipate. Do not block ventilated openings or place the

monitor near a radiator or other heat sources. Do not put anything

on top of monitor.

• The power cable connector is the primary means of detaching the

system from the power supply. The monitor should be installed

close to a power outlet which is easily accessible.

• Handle with care when transporting. Save packaging for

transporting.

CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR

CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK

THE FOLLOWING WHEN YOU POSITION THE MONITOR:

• Adjust the monitor height so that the top of the screen is

at or slightly below eye level. Your eyes should look

slightly downward when viewing the middle of the

screen.

• Position your monitor no closer than 40 cm and no

further away than 70 cm from your eyes. The optimal

distance is 60 cm.

• Rest your eyes periodically by focusing on an object at

least 6 m away. Blink often.

• Position the monitor at a 90° angle to windows and other light sources to

minimize glare and reflections. Adjust the monitor tilt so that ceiling lights do not

reflect on your screen.

• If reflected light makes it hard for you to see your screen, use an anti-glare filter.

• Clean your monitor regularly. Use a lint-free, non-abrasive cloth and a non-

alcohol, neutral, non-abrasive cleaning solution or glass cleaner to minimize dust.

• Adjust the monitor’s brightness and contrast controls to enhance readability.

• Use a document holder placed close to the screen.

• Position whatever you are looking at most of the time (the screen or reference

material) directly in front of you to minimize turning your head while you are

typing.

• Get regular eye checkups.

Ergonomics

To realize the maximum ergonomics benefits, we recommend the following:

• Adjust the Brightness until the background raster disappears

• Do not position the Contrast control to its maximum setting

• Use the preset Size and Position controls with standard signals

• Use the preset Colour Setting and Sides Left/Right controls

• Use non-interlaced signals with a vertical refresh rate between 75-160Hz

• Do not use primary colour blue on a dark background, as it is difficult to see and

may produce eye fatigue due to insufficient contrast

CAUTION

01b_english 22.02.2001, 14:13 Uhr10

English-11

English

ENERGY STAR

®

is a U.S. registered trademark. All other brands and product names are trademarks or

registered trademarks of their respective owners.

As an ENERGY STAR Partner, NEC-Mitsubishi Electric Visual Systems Corporation has determined that

this product meets the ENERGY STAR guidelines for energy efficiency.

The ENERGY STAR emblem does not represent EPA endorsement of any product or service.

All other trademarks mentioned in this manual are the property of their respective owners.

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO

RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG

WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS

THE PRONGS CAN BE FULLY INSERTED.

REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE

COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

CAUTION

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,DO NOT

REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol warns user that uninsulated voltage within the unit may

have sufficient magnitude to cause electric shock. Therefore, it is

dangerous to make any kind of contact with any part inside this unit.

This symbol alerts the user that important literature concerning the

operation and maintenance of this unit has been included. Therefore, it

should be read carefully in order to avoid any problems.

CAUTION

WARNING

RISK OF ELECTRIC SHOCK • DO NOT OPEN

Safety Instruction

VCCI Statement

01b_english 22.02.2001, 14:13 Uhr11

English-12

01b_english 22.02.2001, 14:13 Uhr12

La pagina sta caricando ...

NEC MultiSync® FP1355 Manuale del proprietario

NEC MultiSync® FP1355 Manuale del proprietario

in altre lingue

Documenti correlati