Bosch SMI40E05EU/28 Manuale utente
- Categoria
- Lavastoviglie
- Tipo
- Manuale utente
Dishwasher
en
Operating instructions
9000 405 406 (8906)
Start
9h
6h
3h
End
End
3h
6h
9h
1
2 43
Reset 3 sec.
6
7
91011
5
8
20
21
23
24
25
26
27
28
29
30
32
22
31
en Table of contents
Safety instructions . . . . . . . . . . . . . . . . . 4
Delivery . . . . . . . . . . . . . . . . . . . . . . . . 4
Installation . . . . . . . . . . . . . . . . . . . . . . 4
In daily use . . . . . . . . . . . . . . . . . . . . . 4
Children in the household . . . . . . . . . . 4
Door lock . . . . . . . . . . . . . . . . . . . . . . 4
Damage . . . . . . . . . . . . . . . . . . . . . . . 5
Disposal . . . . . . . . . . . . . . . . . . . . . . . 5
Getting to know your appliance . . . . . . 5
Control panel . . . . . . . . . . . . . . . . . . . 5
Appliance interior . . . . . . . . . . . . . . . . 5
Water softening system . . . . . . . . . . . . . 6
Setting . . . . . . . . . . . . . . . . . . . . . . . . . 6
Water hardness table . . . . . . . . . . . . . 6
Special salt . . . . . . . . . . . . . . . . . . . . . . . 7
Using special salt . . . . . . . . . . . . . . . . 7
Detergents with salt component . . . . . 7
Switching off water softening system . 7
Rinse aid . . . . . . . . . . . . . . . . . . . . . . . . . 8
Setting amount of rinse aid . . . . . . . . . 8
Switching off rinse-aid refill indicator . . 8
Utensils . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Not suitable . . . . . . . . . . . . . . . . . . . . . 9
Glass and utensil damage . . . . . . . . . 9
Loading the dishwasher . . . . . . . . . . . 9
Unloading the dishwasher . . . . . . . . . 9
Cups and glasses . . . . . . . . . . . . . . . . 9
Pans . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Cutlery basket . . . . . . . . . . . . . . . . . . 10
Folding spikes . . . . . . . . . . . . . . . . . 10
Cup support clip . . . . . . . . . . . . . . . . 10
Small accessories holder . . . . . . . . . 10
Knife shelf . . . . . . . . . . . . . . . . . . . . . 11
Adjusting the height of the basket . . 11
Detergent . . . . . . . . . . . . . . . . . . . . . . . . 12
Adding detergent . . . . . . . . . . . . . . . 12
Combination detergent . . . . . . . . . . . 13
Overview of programmes . . . . . . . . . . 14
Programme selection . . . . . . . . . . . . 14
Information about comparability
tests . . . . . . . . . . . . . . . . . . . . . . . . . 14
Additional options . . . . . . . . . . . . . . . . 15
Express Wash . . . . . . . . . . . . . . . . . . 15
Intensive zone . . . . . . . . . . . . . . . . . . 15
Hygiene . . . . . . . . . . . . . . . . . . . . . . . 15
Half load . . . . . . . . . . . . . . . . . . . . . . 15
Extra drying . . . . . . . . . . . . . . . . . . . . 15
Washing the dishes . . . . . . . . . . . . . . . 15
Programme data . . . . . . . . . . . . . . . . 15
Aqua sensor . . . . . . . . . . . . . . . . . . . 15
Switching on the appliance . . . . . . . . 15
Timer programming . . . . . . . . . . . . . . 15
End of programme . . . . . . . . . . . . . . 16
Switching off the appliance . . . . . . . . 16
Interrupting the programme . . . . . . . . 16
Terminating the programme . . . . . . . 16
Changing the programme . . . . . . . . . 16
Intensive drying . . . . . . . . . . . . . . . . . 16
Maintenance and care . . . . . . . . . . . . . 17
Overall condition of the machine . . . . 17
Special salt and rinse aid . . . . . . . . . 17
Filters . . . . . . . . . . . . . . . . . . . . . . . . . 17
Spray arms . . . . . . . . . . . . . . . . . . . . 18
Waste water pump . . . . . . . . . . . . . . . 18
Troubleshooting . . . . . . . . . . . . . . . . . . 19
... when the appliance is switched on 19
... on the appliance . . . . . . . . . . . . . . 19
... during the wash cycle . . . . . . . . . . 20
... on the utensils . . . . . . . . . . . . . . . . 20
Customer service . . . . . . . . . . . . . . . . 21
Installation . . . . . . . . . . . . . . . . . . . . . . 22
Safety instructions . . . . . . . . . . . . . . . 22
Delivery . . . . . . . . . . . . . . . . . . . . . . . 22
Technical specifications . . . . . . . . . . . 22
Installation . . . . . . . . . . . . . . . . . . . . . 23
Waste-water connection . . . . . . . . . . . 23
Fresh water connection . . . . . . . . . . . 23
Electrical connection . . . . . . . . . . . . . 23
Removing the appliance . . . . . . . . . . 23
Transportation . . . . . . . . . . . . . . . . . . 24
Protection against frost . . . . . . . . . . . 24
Waste disposal . . . . . . . . . . . . . . . . . . . 24
Packaging . . . . . . . . . . . . . . . . . . . . . 24
Old appliances . . . . . . . . . . . . . . . . . 24
en
4
Delivery
– Check the packaging and dishwasher
immediately for damage caused in
transit. Do not switch on a damaged
appliance, but contact your supplier.
– Please dispose of the packaging
material in an environmentally friendly
manner.
– Do not let children play with packaging
and its parts. There is a risk of
suffocation from collapsible boxes and
film.
Installation
Read the “Installation” chapter to learn
how to install and connect the appliance
correctly.
In daily use
– Use the dishwasher only in the
household and only for its designed
purpose: for washing domestic dishes.
– Children or people whose physical,
sensory or mental abilities prevent
them from using the appliance safely
must not use this appliance without
supervision or instruction
by a responsible person.
– Do not lean or sit on the open door.
The appliance could tip.
– Please note that free-standing
appliances may tip over if the baskets
are overloaded.
– Do not add any solvents to the washing
chamber. Danger of explosion!
– Open the door carefully when the
programme is still running. There is a
risk of hot water spraying out of the
appliance.
– To prevent injuries, e. g. caused by
stumbling, open the dishwasher only
briefly in order to load and unload
the dishwasher.
– Read and observe the safety
information and instructions for use on
the packaging for cleaning and rinsing
agents.
ã=Warning
Knives and other utensils with sharp points
must be placed in the cutlery basket with
the points downwards or horizontally on
the knife shelf *.
* depending on model
Children in the household
– If fitted, use the childproof lock. An
exact description can be found in the
back of the envelope.
– Do not allow children to play with or
operate the appliance.
– Keep children away from detergents
and rinse aid. These may cause
chemical burns in the mouth, throat
and eyes or asphyxiation.
– Keep children away from open
dishwasher. The water in the rinsing
compartment is not drinking water and
could contain detergent residue.
Ensure that children do not place
fingers in the tablet collecting tray 12.
Small fingers could become caught in
the slots.
– If the appliance is installed at eye-level,
ensure when opening and closing the
door that children are not caught or
crushed between the appliance door
and the cupboard door situated below.
Childproof lock (door lock) *
The description of the childproof lock is at
the back in the envelope.
* depending on model
Safety instructions
en
5
Damage
– The appliance may be repaired and
opened up by a technician only. To do
this, disconnect the appliance from the
power supply. Pull out the mains plug
or switch off the fuse. Turn off the tap.
Disposal
– Make redundant appliances unusable
to prevent subsequent accidents.
– Dispose of the appliance in an
environmentally friendly manner.
ã=Warning
Children could become locked in the
appliance (risk of suffocation) or find
themselves in other dangerous situations.
Therefore: Pull out the mains plug, sever
and dispose of the power cord. Destroy
the door lock so that the door can no
longer be closed.
Diagrams of the control panel and the
interior of the appliance can be found in
the envelope at the front.
Individual positions are referred to in the
text.
Control panel
* depending on model
** Number depending on model
Appliance interior
* depending on model
Getting to know your
appliance
( ON/OFF switch
0 Door opener
8 Programme selector
@ START button
H Timer programming *
P Additional options **
X Rinse aid refill indicator
` Salt refill indicator
h Display “Check water supply”
)" End display
)* Cleaning display
1" Top basket
1* Knife shelf *
12 Tablet collecting tray
1: Top spray arm
1B Bottom spray arm
1J Dispenser for special salt
1R Filters
1Z Cutlery basket
1b Bottom basket
1j Dispenser for rinse aid
9" Detergent dispenser
9* Lock for detergent dispenser
92 Rating plate
en
6
To ensure good washing results, the
dishwasher requires soft water, i.e.
containing low amounts of lime, otherwise
white limescale will be deposited on the
utensils and inner container.
Tap water above a specific degree of
water hardness must be softened, i.e.
descaled, for use in a dishwasher. Water is
softened with special salt in the water
softening system of the dishwasher.
The setting and therefore the required
amount of salt depends on the degree of
hardness of your tap water (see table).
Setting
The amount of salt dispensed can be set
in 4 stages depending on the hardness of
your water. Accordingly 0, 1, 2 or 3
displays are lit (see table). Factory setting:
1.
– Find out about the hardness value of
your tap water. Your water utility
company will help you with this.
– Setting can be found in the water
hardness table.
– Close the door.
– Switch on ON/OFF switch (.
– Press and hold down the START
button @.
– Rotate programme selector 8 until
the salt refill indicator ` flashes.
–Release button.
The salt refill indicator ` flashes and
the display “Check water supply” h
are lit (= Setting 1).
To change the setting:
– Rotate programme selector 8 until
the required setting has been selected.
– Press START button @.
The salt refill indicator ` goes out.
The selected setting is saved.
Water hardness table
Water softening system
,
End
6
° Clarke
0 - 8
soft
9 - 20
medium
21 - 26
hard
27 - 44
hard
mmol/l
0 -1,1
1,2-2,9
3,0-3,7
3,8-6,2
Hardness
range
Setting
0
1
2
3
en
7
Using special salt
Always refill with special salt immediately
before switching on the appliance. This
ensures that overrun special salt solution
is immediately washed out and does not
corrode the rinsing tank.
– Open the screw-type cap of the
compartment 1J.
– Fill the tank with water (only required
when switching on the appliance for
the first time).
– Then add dishwasher salt (not table
salt or tablets).
The water is displaced and runs out.
As soon as the salt refill indicator ` on
the fascia is lit, top up the salt.
* depending on model
Using detergents with salt
component
If combined detergents with a salt
component are used, salt can usually be
omitted up to a water hardness of 21° dH
(37° fH, 26° Clarke, 3.7 mmol/l). If the
water hardness is over 21° dH, special
salt must be used.
Switching off salt refill indicator/
water softening system
If the salt refill indicator ` is impaired
(e.g. when using combined detergents
containing salt component), it can be
switched off.
– Proceed as described under “Adjusting
the water softening system” and select
setting 0.
The water softening system and salt
refill indicator are now switched off.
ã=Warnings
– Never fill the salt dispenser with
detergent. You will destroy the water
softening system.
– To prevent corrosion, always refill with
salt immediately before switching on
the appliance.
Special salt
*
en
8
As soon as the rinse-aid refill indicator X
is lit on the fascia, there is still a rinse-aid
reserve of 1 – 2 rinsing processes. Refill
with rinse aid.
The rinse aid is required for stain-free
utensils and clear glasses. Use only rinse
aid for domestic dishwashers.
Combined detergents with rinse-aid
component may be used up to a water
hardness of 21° dH (37° fH, 26° Clarke,
3.7 mmol/l) only. If the water hardness is
over 21° dH, rinse aid must be used.
–Open the dispenser 1j by pressing
and lifting the plate on the cover.
– Carefully pour rinse aid up to the max.
mark in the filler opening.
– Close cover until it clicks shut.
– To prevent excessive foam formation
during the next rinse cycle, remove any
rinse aid which has run over with a
cloth.
Setting amount of rinse aid
The amount of rinse aid dispensed can be
set in 4 stages. Accordingly 0, 1, 2 or 3
displays are lit (see water hardness table).
Factory setting: 2.
Do not change the amount of rinse aid
unless streaks (select lower setting) or
water stains (select higher setting) are left
on the utensils.
– Close the door.
– Switch on ON/OFF switch (.
– Press and hold down the START
button @.
– Rotate programme selector 8 until
the rinse aid refill indicator X flashes.
–Release button.
The rinse aid refill indicator X flashes
and the displays )" and h are lit
(= Setting 2).
To change the setting:
– Rotate programme selector 8 until
the required setting has been selected.
– Press START button @.
The rinse-aid refill indicator X goes
out. The selected setting is saved.
Switching off rinse-aid refill
indicator
If the rinse-aid refill indicator X is
impaired (e.g. when using combined
detergents containing rinse-aid
component), it can be switched off.
– Proceed as described under “Setting
amount of rinse aid” and select
setting 0.
The rinse aid refill indicator X is now
switched off.
Rinse aid
max
en
9
Not suitable
– Cutlery and utensils made of wood.
– Delicate decorative glasses, craft and
antique utensils. These decors are not
dishwasher-proof.
– Plastic parts not resistant to heat.
–Copper and tin utensils.
– Utensils which are soiled with ash, wax,
lubricating grease or ink.
Aluminium and silver parts have a
tendency to discolour and fade during the
wash cycle. Even some types of glass
(e.g. crystal glass objects) may turn cloudy
after many wash cycles.
Glass and utensil damage
Causes:
– Glass type and glass production
process.
– Chemical composition of the detergent.
– Water temperature of the wash
programme.
Recommendation:
– Use only glasses and porcelain which
the manufacturer designates as
dishwasher-proof.
– Use a detergent which protects
utensils.
– Take glass and cutlery out of the
dishwasher as soon as possible after
the programme ends.
Loading the dishwasher
– Remove large food remnants. It is not
necessary to prerinse utensils under
running water.
– Place the utensils so that
– they are secure and cannot tip over.
– all utensils with their openings face
down.
– parts with curves or indentations
are at an angle, thereby allowing
water to drain.
– does not obstruct rotation of the
two spray arms 1: and 1B.
Very small utensils should not be washed
in the machine, as they may fall out of the
baskets.
Unloading the dishwasher
To prevent water from dripping off the
upper basket onto the utensils in the lower
basket, it is recommended to empty
the appliance from the bottom up.
Hot utensils are sensitive to shock!
Therefore, when the programme ends,
leave the utensils to cool down in the
dishwasher until they can be handled.
Cups and glasses
Top basket 1"
Pans
Bottom basket 1b
Utensils
en
10
Tip
Heavily soiled utensils (pans) should
be placed in the bottom basket. The more
powerful spray jet provides a better
dishwashing result.
Tip
Other examples, such as the best way
of loading your dishwasher, can be found
on our homepage as a free download. The
corresponding Internet address can
be found on the back page of these
instructions for use.
Cutlery basket
You should always place cutlery unsorted
with the points downwards.
To prevent injuries, place long, pointed
implements and knives on the knife shelf.
Folding spikes *
* depending on model
The spikes can be folded down to improve
arrangement of pans, bowls and glasses.
Cup support clip *
* depending on model
When washing cups, the cup support clip
can be folded up. The additional inclined
position reduces the accumulation
of water on the underside of the cup.
In the case of tall glasses
it is recommended to fold down
the cup support clip.
Small accessories holder *
* depending on model
Light-weight plastic accessories, e.g. cups,
lids, etc. can be held securely in the small
accessories holder.
1
2
en
11
Knife shelf *
* depending on model
Long knives and other utensils can be
arranged horizontally.
You can remove the knife shelf to wash
taller utensils. Re-insert the knife shelf in
the correct position.
Adjusting the height of the
basket *
* depending on model
If required, the height of the upper utensils
basket 1" can be adjusted to provide
more space for tall utensils either in the
upper or lower basket.
Appliance height 81.5 cm
Appliance height 86.5 cm
Select one of the two following procedures
according to the design of the top basket
for your appliance model:
Top basket with side levers
– Pull out the top basket 1" out.
–To lower the basket, press in the left
and then the right lever on the outside
of the basket. In doing so, hold the
sides of the basket along the upper
edge to prevent it from suddenly
dropping.
–To raise the basket, hold the basket on
the sides of the upper edge and lift it
up.
– Before re-inserting the basket again,
ensure that it is at the same height on
both sides. Otherwise, the appliance
door cannot be closed and the upper
spray arm will not be connected to the
water circuit.
Top basket with upper and lower
roller pairs
– Pull out the top basket 1" out.
– Remove the upper basket and re-
attach it to the upper (stage 3) or lower
(stage 1) rollers.
Top basket Bottom
basket
Setting 1 max. ø 22 cm 30 cm
Setting 2 max. ø 24.5 cm 27.5 cm
Setting 3 max. ø 27 cm 25 cm
Top basket Bottom
basket
Setting 1 max. ø 24 cm 33 cm
Setting 2 max. ø 26.5 cm 30.5 cm
Setting 3 max. ø 29 cm 28 cm
en
12
You can use tablets as well as powder
or liquid detergents for dishwashers, but
never use washing up liquid. The dosage
can be individually adjusted with powder
or a liquid detergent according
to the degree of soiling. Tablets contain
an adequately large amount of active
ingredients for all cleaning tasks. Modern,
powerful detergents predominantly
use a low-alkaline formulation with
phosphate and enzymes. Phosphates
bond the lime in the water. Enzymes break
down starch and remove protein.
Phosphate-free detergents are less
frequent. These have a slightly weaker
lime bonding capacity and require
a higher dosage. To remove coloured
stains (e.g. tea, tomato sauce), oxygen-
based bleaching agents are usually used.
Note
To ensure a good washing result, always
follow the instructions on the detergent
packaging!
If you have further questions,
we recommend that you contact
the detergent manufacturers’ helpline.
ã=Warning
Read and observe the safety information
and instructions for use on the packaging
for cleaning and rinsing agents.
Adding detergent
– If the detergent dispenser 9" is still
closed, press the lock 9* to open the
detergent dispenser.
Pour detergent into the dry detergent
dispenser 9" only (insert tablet flat,
not on its edge).
Dosage: see manufacturer’s
instructions on the packaging.
The graduated detergent
dispenser 9" helps you add the
correct amount of powder or liquid
detergent.
Usually 20 ml–25 ml are adequate
for normal soiling. If using tablets, one
tablet is adequate.
– Close the cover on the detergent
dispenser by sliding it up until the lock
engages without difficulty.
The detergent dispenser opens
automatically at the optimum time
depending on the programme.
The powder or liquid detergent
is distributed in the appliance and is
dissolved, the tablet falls into the tablet
collecting tray where it dissolves
in doses.
Detergent
15 ml
25 ml
50 ml
en
13
Tip
If the utensils are only lightly soiled, slightly
less than the indicated amount
of detergent is usually adequate.
Suitable detergents and care products
can be purchased online via our website
or via customer service (see back page).
Combination detergent
Apart from conventional detergents (Solo),
a number of products are offered with
additional functions. These products
contain not only the detergent but also
rinse-aid and salt replacement substances
(3in1) and, depending on the combination
(4in1, 5in1, etc.), additional components
such as glass protection or stainless steel
cleaner. Combination detergents function
only up to a specific degree of hardness
(usually 21°dH). Over this limit salt and
rinse-aid must be added.
As soon as combined detergents
are used, the rinse programme is adjusted
automatically to ensure the best possible
rinsing and drying result.
ã=Warnings
–Do not place small parts for washing in
the tablet collecting tray 12; this
prevents the tablet from dissolving
evenly.
– If you want to add more utensils after
the programme has started, do not
use the tablet collecting tray 12
as a handle for the upper basket.
The tablet could already be there and
you will touch the partially dissolved
tablet.
Notes
– You will obtain optimum rinsing
and drying results by using solo
detergents and applying salt and rinse
aid separately.
– If programmes are short, tablets
may not have full cleaning effect due to
different dissolving properties
and there may even be undissolved
detergent residue. It is recommended
to use washing powder for these
programmes.
– The Intensive programme (on some
models) requires one tab only. When
using washing powder, you can apply
some of this cleaning agent to the
inside of the appliance’s door.
– Even if the rinse-aid and/or salt refill
indicator is lit, the rinse programme will
run correctly with combined
detergents.
– If using detergents in a water-soluble
protective cover: Take hold of the
cover with dry hands only and put
the detergent into an absolutely
dry detergent dispenser only, otherwise
the detergent may stick.
– If you switch from combined
detergents to solo detergents, ensure
that the water softening system and
amount of rinse aid have been set to
the correct value.
en
14
The max. possible number of programmes is illustrated in this overview.
The corresponding programmes for your appliance can be found on the fascia.
Programme selection
You can select a suitable programme
according to the type of utensils and
degree of soiling.
Information about comparability
tests
The conditions for the comparison test
are available on request by e-mail from
Quote the appliance number (ENr.)
and the production date (FD) which you
can find on the rating plate 92 on the
appliance door.
Overview of programmes
Type of utensils Type of soiling Programme Possible additional
options
Programme sequence
pots and pans,
non-sensitive
utensils
and cutlery
very adhesive burned-
in or dried-on food
remnants containing
starch or protein
± / °
Intensive 70°
all
Prerinse
Clean 70°
Intermediate rinse
Final rinse 65°
Dry
Ù / Ø
Normal 65°
Prerinse
Clean 65°
Intermediate rinse
Final rinse 65°
Dry
mixed utensils
and cutlery
part dried, common
household food
remnants
á / à
Eco 50°
Prerinse
Clean 50°
Intermediate rinse
Final rinse 65°
Dry
sensitive utensils,
cutlery,
temperature-
sensitive plastic
and glasses
slightly adhesive,
fresh food remnants
é / è
Gentle 40°
Intensive zone
Express Wash
Half load
Extra drying
Prerinse
Clean 40°
Intermediate rinse
Final rinse 55°
Dry
ñ / ð
Quick 45°
Extra drying
Clean 45°
Intermediate rinse
Final rinse 55°
all types of utensils
cold rinsing,
intermediate cleaning
ù / ø
Prerinse
none Prerinse
en
15
* depending on model
Additional options can be set with the
buttons P.
Ÿ Express Wash *
The >>Express Wash<< function can
reduce the running time by approx. 20% to
50% depending on the selected rinse
programme. To obtain optimum cleaning
and drying results at a reduced running
time, water and energy consumption are
increased.
Ï Intensive zone *
Perfect for a mixed load. You can wash
very soiled pots and pans in the lower
basket together with normally soiled
utensils in the upper basket. The spray
pressure in the lower basket is intensified,
the rinsing temperature is increased
slightly.
· Hygiene *
The temperature is increased during the
cleaning process. This increases the
hygiene status. This additional option is
ideal for cleaning e.g. chopping boards
and baby bottles.
§ Half load *
If you have only a few items to wash (e.g.
glasses, cups, plates), you can switch to
“half load”. This will save water, energy
and time. It is recommended to put a little
less detergent in the detergent dispenser
than for a full load.
¿ Extra drying *
An increased temperature during the final
rinse and an extended drying phase
ensure that even plastic parts dry better.
There is a slight increase in the energy
consumption.
Programme data
The programme data (consumption
values) can be found in the summary
of instructions. This data refers to normal
conditions and the water hardness set
value 2. Different influencing factors such
as water temperature or mains pressure
may result in deviations.
Aqua sensor *
* depending on model
The Aqua sensor is an optical measuring
device (light barrier) which measures the
turbidity of the rinsing water.
The Aqua sensor is used according to the
programme. If the Aqua sensor is active,
“clean” rinsing water can be transferred to
the next rinse bath and water consumption
can be reduced by 3–6 litres. If the
turbidity is greater, the water is drained
and is replaced with fresh water. In the
automatic programmes the temperature
and running time can also be adjusted to
the degree of soiling.
Switching on the appliance
– Turn on the tap fully.
– Switch on ON/OFF switch (.
– Rotate programme selector 8 to the
required programme.
– Press START button @.
The Cleaning display )* is lit. he
programme starts running.
Timer programming *
* depending on model
You can delay the start of the programme
by 3, 6 or 9 hours.
– Switch on ON/OFF switch (.
– Keep pressing the Preselected starting
time button H until the appropriate
display 3h, 6h or 9h is lit.
– Press START button @, timer
programming is activated.
– To delete the preselected starting time,
keep pressing the Preselected starting
time button H until none of the
displays 3h, 6h or 9h is lit.
You can change your programme
selection at any time until the
programme starts.
Additional options Washing the dishes
en
16
End of programme
The programme has ended when the End
display )" is lit.
Switching off the appliance
Short time after the end of the programme:
– Switch off ON/OFF switch (.
– Turn off the tap (not applicable if Aqua-
Stop fitted).
– Remove the utensils when they have
cooled down.
ã=Warning
At the end of the programme please open
the door fully and not partially when
emptying the dishwasher. Any escaping
water vapour could damage sensitive
worktops.
Interrupting the programme
– Switch off ON/OFF switch (.
The LEDs go out. The programme is
saved.
If the door was opened on an
appliance which has a warm water
connection or is heated, first leave the
door ajar for several minutes and then
close. Otherwise, expansion (pressure)
may cause the appliance door to
spring open or water to run out of the
appliance.
– To continue the programme, switch on
the ON/OFF switch ( again.
Terminating the programme
(Reset)
–Press START button @ for approx.
3sec.
The End display )" is lit.
– The remaining programme sequence
lasts approx. 1 minute.
Switch off ON/OFF switch (.
Changing the programme
When the START button @ has been
pressed, the programme cannot be
changed.
The only way a programme can be
changed is by Cancel programme (Reset).
Intensive drying
The final rinse uses a higher temperature
which improves the drying result. The
running time may increase slightly.
(Caution if utensils are delicate!)
– Close the door.
– Switch on ON/OFF switch (.
– Press and hold down the START
button @.
– Rotate programme selector 8 until
the “Check water supply” display h
flashes.
–Release button.
To change the setting,
– By rotating the programme selector
8, you can switch on intensive
drying (End display)" is lit) or switch
off intensive drying (End display )" is
not lit).
– Press START button @.
The setting is saved.
en
17
A regular inspection and maintenance of
your machine will help to prevent faults.
This saves time and prevents problems.
Overall condition of the machine
– Check spray arm for grease and
limescale deposits.
If you find such deposits:
– Fill detergent dispenser with detergent.
Start the appliance without utensils in
the programme with the highest rinsing
temperature.
Clean the appliance with detergents/
appliance cleaners which are particularly
suitable for use with dishwashers.
– Regularly clean door seal with a damp
cloth.
Never use a steam cleaner to clean your
dishwasher. The manufacturer is not liable
for any consequential damage.
Regularly wipe the front of the appliance
and fascia with a damp cloth; water and a
little washing up liquid are adequate. Do
not use sponges with a rough surface or
abrasive detergents, as these could
scratch the surfaces.
Stainless steel appliances: To prevent
corrosion, avoid using sponge cloths or
wash them out thoroughly several times
before using for the first time.
ã=Warning
Never use other chlorinated household
detergents! Health hazard!
Special salt and rinse aid
– Check the refill indicators ` and
X. If required, refill salt and/or rinse
aid.
Filters
The filters 1R keep large foreign objects
in the rinsing water away from the pump.
These foreign objects may occasionally
block the filters.
The filter system consists of a coarse filter,
a flat fine filter and a microfilter.
– After each washing cycle check the
filters for residue.
– Unscrew filter cylinder as illustrated
and take out filter system.
– Remove any residue and clean filters
under running water.
– Re-install filter system in reverse
sequence and ensure that the arrow
marks are opposite each other after
closing the filter system.
Maintenance and care
en
18
Spray arms
Limescale and contaminants in the rinsing
water may block nozzles and bearings on
the spray arms 1: and 1B.
–Check outlet nozzles on the spray arms
for blockages.
– Unscrew the upper spray arm 1:.
– Remove the lower spray arm 1B
upwards.
– Clean spray arms under running water.
– Re-engage or screw on spray arms.
Waste water pump
Large food remnants in the rinsing water
not retained by the filters may block the
waste water pump. The rinsing water is
then not pumped out and covers the filter.
In this case:
– First disconnect the appliance from the
power supply.
– Remove the filters 1R.
– Scoop out water, use a sponge if
required.
– Using a spoon, prise off pump cover
(as illustrated) until it clicks, then grip
the cover by the lug and first pull it
upwards until it resists and then pull it
out forwards.
– Check inner compartment and remove
any foreign objects.
– Place cover in the original position,
press down and engage.
– Install filters.
1
2
1
2
3
Klick
en
19
The majority of faults which could occur in
daily operation can be rectified by the
user. This ensures that the appliance is
quickly available for use again. The
following overview will help you locating
the causes and gives helpful advise to
eliminate them.
ã=Warning
Don’t forget: Repairs may be carried out
by technicians only. If a component has to
be replaced, ensure that only original
spare parts are used. Improper repairs or
use of non-original spare parts may cause
considerable damage and put the user at
considerable risk.
... when the appliance is
switched on
The appliance does not start.
– The mains fuse has tripped.
– The appliance plug has not been
inserted.
– The appliance door has not been shut
properly.
... on the appliance
Lower spray arm rotates sluggishly.
– Spray arm blocked.
The door is difficult to open. *
– Child-proof lock is activated. The
deactivation instructions are at the
back in the envelope.
* depending on model
Door cannot be closed.
– Door lock has been activated. To reset,
close the door with greater force.
Cover on the detergent dispenser cannot
be closed.
– Detergent dispenser overfilled or
mechanism blocked by sticky
detergent residue.
Detergent residue in the detergent
dispenser.
– Dispenser was damp when filled.
“Check water supply” display h lights
up.
– Tap turned off.
– Water supply interrupted.
–Supply hose kinked.
– Filter in the water supply blocked.
– Switch off the appliance and pull
out the mains plug.
– Turn off the tap.
– Clean filter in the supply hose.
– Reconnect power supply.
– Turn on the tap.
– Switch on the appliance.
– Water is left in the appliance at the end
of the programme.
– Waste water hose is blocked or
kinked.
– Waste water pump blocked, cover
on the waste water pump is not
locked in position
(see Maintenance and care).
–Filters blocked.
– The programme has not yet ended.
Wait until programme ends or
implement “Reset” function.
The “Check water supply” display h
flashes rapidly.
– Water in the safety system.
– Switch off the appliance and pull
out the mains plug.
– Turn off the tap.
– Call customer service.
Refill indicator for salt ` and/or rinse-
aid X is not lit.
– Refill indicator/s switched off.
– Adequate salt/rinse-aid available.
Troubleshooting
en
20
Refill indicator for special salt ` is lit.
–No salt.
Refill with special salt.
– Sensor does not detect salt tablets.
Use different special salt.
... during the wash cycle
Unusual foam formation.
– Handwash liquid in the rinse aid
dispenser.
Spilled rinse aid causes excessive
frothing, therefore please remove with
a cloth.
Appliance stops during the wash cycle.
– Power supply interrupted.
– Water supply interrupted.
Filling valves making striking noises
– Caused by the installation of the water
line and has no effect on the function
of the machine. Remedial action is not
possible.
Knocking/rattling noise during rinsing
– Spray arm is striking utensils.
– Utensils not arranged correctly.
... on the utensils
Food residue on the utensils.
– Utensils placed too closely together,
utensils basket overfilled.
– Too little detergent.
– Rinse programme too weak.
– Spray arm rotation obstructed.
– Spray arm nozzles blocked.
–Filters blocked.
– Filters incorrectly inserted.
– Waste water pump blocked.
– Top basket on right and left not set to
same height.
Tea or lipstick residue is not completely
removed.
– The detergent has an inadequate
bleaching effect.
– Too low rinsing temperature.
– Too little/unsuitable detergent.
White stains on the utensils/glasses
remain milky.
If phosphate-free detergents are used with
hard tap water, white deposits may be
deposited more easily on utensils and
the container walls.
– Too little/unsuitable detergent.
– Too weak programme selected.
– No/too little rinse aid.
– No/too little special salt.
– Water softening system set to the
wrong value.
– Salt dispenser lock not fastened.
Contact the detergent manufacturer,
in particular if:
– the utensils are very wet at the end of
the programme.
– limescale forms.
Dull, discoloured glasses, film cannot be
washed off.
– Unsuitable detergent.
– Glasses not dishwasher-proof.
Streaks on glasses and cutlery, glasses
have metallic appearance.
– Too much rinse aid.
Plastic parts discoloured.
– Too little/unsuitable detergent.
– Too weak programme selected.
Rust spots on the cutlery.
– Cutlery not rust-resistant.
– Salt content in the rinsing water too
high, as salt dispenser lock not
fastened firmly or salt was spilled while
being refilled.
Utensils not dry.
– Appliance door opened too early and
utensils taken out too early.
– Programme selected without drying.
– Too little/unsuitable rinse aid.
– Activate intensive drying.
– The combined detergent used has
a poor drying performance.
Use rinse aid (see Rinse aid chapter
for setting).
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
Bosch SMI40E05EU/28 Manuale utente
- Categoria
- Lavastoviglie
- Tipo
- Manuale utente
in altre lingue
- English: Bosch SMI40E05EU/28 User manual