Hitachi RAK-50PXA Istruzioni per l'uso

– 1 –

ENGLISHDEUTSCHFRANÇAISITALIANOESPAÑOL

PORTUGUÊS

Eλληνικά РУССКИЙ

SPLIT TYPE AIR CONDITIONER

INDOOR UNIT / OUTDOOR UNIT

MODEL

RAK-50PXA / RAC-50WXA

OUTDOOR UNIT INDOOR UNIT

RAC-50WXA

RAK-50PXA

RAK-50PXA/RAC-50WXA (EN1).indd 1 3/28/13 12:42 PM

– 2 –

SAFETY PRECAUTION

O Please read the “Safety Precaution” carefully before operating the unit to ensure correct usage of the unit.

O Pay special attention to signs of “

!

Warning” and “

!

Caution”. The “Warning” section contains matters which, if not

observed strictly, may cause death or serious injury. The “Caution” section contains matters which may result in serious

consequences if not observed properly. Please observe all instructions strictly to ensure safety.

O The sign indicate the following meaning

O Please keep this manual after reading.

PRECAUTIONS DURING OPERATION

O Avoid an extended period of direct air  ow for your health.

W

A

R

N

I

N

G

!

O Do not insert a  nger, a rod or other objects into the air outlet or inlet. As the fan is rotating

at a high speed, it will cause injury. Before cleaning, be sure to stop the operation and turn

the breaker OFF.

O Do not use any conductor as fuse wire, this could cause fatal accident.

PRECAUTIONS DURING SHIFTING OR MAINTENANCE

O Should abnormal situation arises (like burning smell), please stop operating the unit and turn

off the circuit breaker. Contact your agent. Fault, short circuit or  re may occur if you continue

to operate the unit under abnormal situation.

OPlease contact your agent for maintenance. Improper self maintenance may cause electric

shock and  re.

OPlease contact your agent if you need to remove and reinstall the unit. Electric shock or  re

may occur if you remove and reinstall the unit yourself improperly.

OIf the supply cord is damaged, it must be replaced by the special cord obtainable at

authorized service/parts centers.

W

A

R

N

I

N

G

!

O

During thunder storm, disconnect and turn off the circuit breaker.

WARNING

PRECAUTIONS DURING INSTALLATION

O Do not reconstruct the unit.

Water leakage, fault, short circuit or  re may occur if you reconstruct the unit by yourself.

O Please ask your sales agent or quali ed technician for the installation of your unit. Water

leakage, short circuit or  re may occur if you install the unit by yourself.

O Please use earth line.

Do not place the earth line near water or gas pipes, lightning-conductor, or the earth

line of telephone. Improper installation of earth line may cause electric shock.

O Be sure to use the speci ed piping set for R410A. Otherwise, this may result in broken

copper pipes or faults.

O A circuit breaker should be installed depending on the mounting site of the unit. Without

a circuit breaker, the danger of electric shock exists.

O Do not install near location where there is  ammable gas. The outdoor unit may catch

 re if  ammable gas leaks around it.

O Please ensure smooth  ow of water when installing the drain hose.

O Do not install the indoor unit in a machine shop or kitchen where vapor from oil or its

mist  ows to the indoor unit. The oil will deposit on the heat exchanger, thereby reducing

the indoor unit performance and may deform and in the worst case, break the plastic

parts of the indoor unit.

CAUTION

!

O

Spray cans and other combustibles should not be located within a meter of the air outlets

of both indoor and outdoor units.

As a spray can’s internal pressure can be increased by hot air, a rupture may result.

Make sure to connect earth line. The sign in the  gure indicates prohibition.

Indicates the instructions that must be followed.

RAK-50PXA-RAC-50WXA (EN2).indd 2 3/28/13 12:41 PM

– 3 –

ENGLISH

PRECAUTIONS DURING OPERATION

O Do not attempt to operate the unit with wet hands, this could cause fatal

accident.

O When operating the unit with burning equipments, regularly ventilate the

room to avoid oxygen insuf ciency.

O Do not direct the cool air coming out from the air-conditioner panel to face

household heating apparatus as this may affect the working of apparatus

such as the electric kettle, oven etc.

O Do not use any aerosol or hair sprays near the indoor unit. This chemical

can adhere on heat exchanger  n and blocked the evaporation water  ow

to drain pan. The water will drop on tangential fan and cause water splashing

out from indoor unit.

O Please ensure that outdoor mounting frame is always stable,  rm and

without defect. If not, the outdoor unit may collapse and cause danger.

O Do not splash or direct water to the body of the unit when cleaning it as

this may cause short circuit.

O When operating the unit with the door and windows opened, (the room humidity is always above

80%) and with the air de ector facing down or moving automatically for a long period of time,

water will condense on the air de ector and drips down occasionally. This will wet your furniture.

Therefore, do not operate under such condition for a long time.

O If the amount of heat in the room is above the cooling or heating capability of the unit (for

example: more people entering the room, using heating equipments and etc.), the preset room

temperature cannot be achieved.

O

This appliance is not intended for use by young children or in rm persons unless they have been

adequately supervised by a responsible person to ensure that they can use the appliance safely.

O Young children should be supervised to ensure that they do not play with the appliance.

O Do not climb on the outdoor unit or put objects on it.

O Please switch off the unit and turn off the circuit breaker during cleaning,

the high-speed fan inside the unit may cause danger.

O Turn off the circuit breaker if the unit is not to be operated for a long period.

C

A

U

T

I

O

N

O The product shall be operated under the manufacturer speci cation and

not for any other intended use.

O Do not put water container (like vase) on the indoor unit to avoid water

dripping into the unit. Dripping water will damage the insulator inside the

unit and causes short-circuit.

O Do not place plants directly under the air  ow as it is bad for the plants.

!

RAK-50PXA-RAC-50WXA (EN2).indd 3 3/28/13 12:41 PM

– 4 –

INDOOR UNIT

NAMES AND FUNCTIONS OF EACH PART

Electrical Dust Collector

Negative ions are generated to capture all air-borne

dirt and dust particle.

AIR PURIFYING FILTER

Pre- lter

To prevent dust from coming into the indoor unit.

FRONT PANEL

MOVEABLE PANEL

It will be open when the air conditioner is operate

and close when the air conditioner is not in operation.

(Occasionally it may not be open during the operating

mode)

HORIZONTAL DEFLECTOR

O

VERTICAL

DEFLECTOR (AIR OUTLET)

Indoor unit indicators

Light indicator showing the operating condition.

WIDTH (mm)

795

MODEL

HEIGHT (mm)

295

DEPTH (mm)

198

MODEL NAME AND DIMENSIONS

Q Moveable Panel

O It will open up automatically when the air conditioner is in operation to allow a large quantity of air

 owing through as a sort of heat exchange; and it will close up automatically when the air conditioner

stopped operating. Avoid physical adjustments as it may damage the panels’ mechanisms.

O Please do not touch the moving panels during operations as they may pinch your  ngers.

RAK-50PXA

REMOTE CONTROLLER

Send out operation signal to the indoor unit. So as to

operate the whole unit.

(Refer Remote control manual)

RAC-50WXA 792 600 299

OUTDOOR UNIT

Drain pipe

Condensed water drain to outside.

Connecting cord and insulation pipe for piping

Air inlet (Back, Right and Left side)

Air outlet

O Air purifying and deodorizing  lters are not washable and reusable up to 20 times by using vacuum cleaner or water

rinse under running tap water. Type number for this air cleansing  lter is <SPX-CFH22>. Please use this number

for ordering when you want to renew it.

O Air purifying  lter should be cleaned every month or sooner if noticeable loading occurs. When used overtime,

it may loose its deodorizing function. For maximum performance, it is recommended to replace it every 1 year

depending on application requirements.

NOTE

RAK-50PXA-RAC-50WXA (EN2).indd 4 3/28/13 12:41 PM

– 5 –

ENGLISH

INDOOR UNIT INDICATORS

FILTER LAMP

When the device is operated for a total of about 200

hours, the FILTER lamp lights to indicate that it is time

to clean the  lter. The lamp goes out when the “

(AUTO SWING)” button is pressed while the device is on

“STANDBY MODE”.

OPERATION LAMP

This lamp lights during operation.

The OPERATION LAMP  ashes in the following cases

during heating.

(1) During preheating

For about 2–3 minutes after starting up.

(2) During defrosting

Defrosting will be performed about once every one

hour when frost forms on the heat exchanger of the

outdoor unit, for 5–10 minutes each time.

SIGNAL RECEIVING PORT

TIMER LAMP

This lamp lights when the timer is working.

OPERATION INDICATOR

TEMPORARY SWITCH

Use this switch to start and stop when the remote controller does not work.

O By pressing the temporary switch, the operation is done in previously set operation mode.

O When the operation is done using the temporary switch after the power source is turned off and turn on

again, the operation is done in automatic mode.

TEMPORARY

SWIT

TEMPORARY

SWIT

Front panel

Moveable panel

Hand grip point

O Lift the front panel

Hand grip point

O Do not hold the moveable panel when

the front panel is in either opened/

closed position.

1. Opening up the front panel

O Never try to force open/close the moveable panel manually.

Manually opening or closing the moveable panel may cause breakdowns (The moveable panel will

automatically close or open when the power supply is switched on or switched off and whenever the

unit is in operations or has stopped operating.

!

CAUTION

RAK-50PXA-RAC-50WXA (EN2).indd 5 3/28/13 12:41 PM

– 6 –

Minimum Maximum Minimum Maximum

Indoor Dry bulb °C 21 32 20 27

Wet bulb °C 15 23 12 19

Outdoor Dry bulb °C 21 43 2 21

Wet bulb °C 15 26 1 15

Cooling Heating

O Pull toward the down direction.

2. Closing the Front Panel

O When front panel is shaky, there is a possibility panel coming off

and falling down.

O Do not apply extra force on the front panel when it is opened up in

the upright position.

Also frequent removal of the front panel from the front cover may

cause damage.

CAUTION

!

O Initially press the left and the right sides of the front

panel and  nally press the central portion until you

hear a clicking sound.

Note

O The recommended temperature range for safety testing should be as below:

RAK-50PXA-RAC-50WXA (EN2).indd 6 3/28/13 12:41 PM

– 7 –

ENGLISH

PREPARATION BEFORE OPERATION

Ƶ To install the batteries

Ƶ To fix the remote controller holder to the wall

1. Slide the cover to take it off.

2. Install two dry batteries AAA.LR03 (alkaline).

The direction of the batteries should match the

marks in the case.

3. Replace the cover at its original position.

1. Choose a place from where the signals can reach the unit.

2. Fix the remote controller holder to a wall, a pillar or similar

location with the provided screws.

3. Place the remote controller in the remote controller holder.

NOTE

Notes on batteries

ƽ When replacing the batteries, use batteries of the same

type, and replace both old batteries together.

ƽ When the system is not used for a long time, take the

batteries out.

ƽThe batteries will last for approximately 1 year. However, if

the remote controller display begins to fade and degradation

of reception performance occurs within a year, replace both

batteries with new size AAA.LR03 (alkaline).

ƽThe attached batteries are provided for the initial use of

the system.

The usable period of the batteries may be short depending

on the manufactured date of the air conditioner.

Notes on the remote controller

ƽNever expose the remote controller to direct sunlight.

ƽDust on the signal transmitter or receiver will reduce the

sensitivity. Wipe off dust with soft cloth.

ƽSignal communication may be disabled if an electronic-

starter-type uorescent lamp (such as inverter-type lamps)

is in the room. Consult the shop if that is the case.

ƽ If the remote controller signals happen to operate another

appliance, move that appliance to somewhere else, or

consult the service shop.

ƽ When the remote controller is not in use, please close the

slide cover to prevent failure.

Remote controller

Screws

Remote controller holder

– 8 –

PREPARATION BEFORE OPERATION

Ƶ To set calendar and clock

1. Press (RESET) button when first time setting.

"Year" blinks.

2. Press

(TIME) button to set the current year.

3. Press

(CLOCK) button. "Day" and "Month"

blink.

4. Press

(TIME) button to set the current day and

month.

5. Press

(CLOCK) button. "CLOCK" blinks.

6. Press

(TIME) button to set the clock to the current

time.

7. Press

(CLOCK) button.

Calendar and clock are set.

To modify the calendar and clock, press

(CLOCK)

button.

Then follow steps 1 to 7.

Calendar and clock need to be set again after

After changing the batteries,

1. Press

(RESET) button.

2. Direct remote controller towards indoor unit and

3. The calendar and clock from indoor unit will be transmitted.

Ƶ Calendar and clock will not be transmitted from indoor

unit when the following occurs:

ƽ When there is a power failure.

ƽ When breaker is OFF by user (unit is not in STANDBY

MODE).

NOTE

Note on setting the calendar and clock.

ƽ If the calendar and clock are not set, the ON-timer, OFF-timer and Weekly Timer cannot be set.

ƽ If the calendar and clock are not set correctly, the ON-timer, OFF-timer and Weekly Timer will not

operate correctly.

ƽ When the ON-timer, OFF-timer and Weekly Timer are set, the calendar and clock cannot be changed. If

changing batteries.

press (INFO) button.

there is a need to change the calendar and clock, ON-timer, OFF-timer and Weekly Timer need to be

cancelled.

AIR PURIFYS

– 9 –

ENGLISH

REMOTE CONTROLLER

ƽ This controls the operation of the indoor unit. The range of control is about 7 meters. If indoor lighting is

controlled electronically, the range of control may be shorter.

be controlled from the remote controller.

ƽ Handle the remote controller with care. Dropping it or getting it wet may compromise its signal transmission

capability.

ƽ After new batteries are inserted into the remote controller, the unit will initially require approximately 10

seconds to respond to commands and operate.

ƽ When remote controller is not in use for about 3 minutes during OFF condition, indicated by on the

display, the LCD will turn off.

ƽ During clock setting, the LCD will turn off about 10 minutes later if the remote controller is not in use.

ƽ When pressing any button, the LCD will turn on.

ƽ The LCD will not turn off during TIMER setting.

Signal Transmitting/Receiving

Window

Point this window towards the

indoor unit when controlling it.

Sensor

A temperature sensor inside the

remote controller senses ambient

temperature around the remote-

controller.

Display

This indicates the room temperature

selected, current time, timer status,

function and airflow rate selected.

ROOM TEMPERATURE setting Buttons

Press these buttons to set the room

temperature.

Press the [

] button to raise the room

temperature.

Press the [

] button to lower the room

temperature.

Keep pressing and the value will change

more quickly.

ECO Button

Use this button to set the ECO

START/STOP button

Press this button to start

operation. Press it again to stop

operation.

FAN SPEED selector Button

This determines the fan speed.

Every time you press this button,

the ange

from

(AUTO) (HIG H)

(MED) (LOW)

(SILENT) (This button allows

optimal or preferred

fan speed for each operation mode).

Transmission sign

The transmission sign lights up

䇆

NAMES AND FUNCTIONS OF REMOTE

when a signal is sent.

airflow rate will ch

selection of

CONTROLLER

ler

mode.( p.19 )

– 10 –

MODE SELECTOR

AUTO

HEAT

DEHUMIDIFY

COOL

FAN

FAN SPEED

AUTO

SILENT

LOW

MED

HI

START / STOP

ECO

Precautions for Use

ƽ

Do not put the remote controller in the following places.

ƽ

Under direct sunlight.

ƽ

In the vicinity of a heater.

ƽ

Handle the remote controller carefully. Do not drop it on the floor, and protect it from water.

ƽ

Once the outdoor unit stops, it will not restart for about 3 minutes (unless you turn the power switch

off and on or unplug the power cord and plug it in again).

This is to protect the device and does not indicate a failure.

ƽ

If you press the MODE selector button during operation, the device may stop for about 3 minutes for

protection.

POWERFUL Button

Use this button to set the

POWERFUL mode.

INFORMATION Button

ONE TOUCH CLEAN Button

ON / OFF TIMER setting Buttons

MODE selector Button

Use this button to select the

operating mode. Every time you

press this button, the mode will

change from

(AUTO)

(HEAT)

(DEHUMIDIFY)

(COOL) and (FAN)

cyclically.

SILENT Button

Use this button to set the SILENT

mode.

AUTO SWING (Vertical) Button

Controls the angle of the

.rotce lfed ria latnoziroh

AIR PURIFIER Button

WEEKLY TIMER setting Buttons

LEAVE HOME Button

ECO SLEEP TIMER Button

Use this button to set the eco sleep

timer.

FAN

POWERFUL

SILENT

INFO

SLEEP TIMER

AUTO SWING (VERTICAL)

AIR PURIFIER

LEAVE HOME

CLEAN

DAY

PROGRAM NO.

ON / OFF TIMER

TIME

OK

DELETE

COPY / PASTE

CANCEL

SEND

CLOCK

AIR PURIFYS

䇆

䇆䇆

Use this button to start air purifying

function.

NAMES AND FUNCTIONS OF REMOTE CONTROLLER

( p.17)

( p.31)

( p.21)

( p.20 )

( p.22)

( p.23)

( p.18 )

( p.25)

( p.16)

– 11 –

ENGLISH

AUTOMATIC OPERATION

The device will automatically determine the mode of operation, HEAT or COOL depending on the current

room temperature. The selected mode of operation will change when the room temperature varies.

However, the mode of operation will not change when indoor unit is connected to multi type outdoor unit.

VARIOUS FUNCTIONS

Ƶ Auto Restart Control

ƽ If there is a power failure, operation will be automatically restarted when the power is resumed with previous operation

mode and airflow direction.

(As the operation is not stopped by remote controller.)

ƽ If you intend not to continue the operation when the power is resumed, switch off the power supply.

When you switch on the circuit breaker, the operation will be automatically restarted with previous operation mode

and air flow direction.

Note: 1. If you do not require Auto Restart Control, please consult your sales agent.

2. Auto Restart Control is not available when

Timer or Sleep Timer mode is set.

Ƶ As the settings are stored in the memory the remote controller, you

(START/STOP) button next time.

Press the MODE selector button so that the display indicates the

(AUTO) mode of operation.

ƽ When AUTO has been selected, the device will automatically

determine the mode of operation, HEAT or COOL depending on

the current room temperature. However the mode of operation will

not change when indoor unit is connected to multi type outdoor

unit.

ƽ If the mode automatically selected by the unit is not satisfactory,

manually change the mode setting (HEAT, DEHUMIDIFY, COOL

or FAN).

Press the (FAN SPEED) button to select AUTO, HI, MED, LOW or

SILENT.

Press the

(START/STOP) button.

Operation starts with a beep.

Press the button again to stop operation.

Set the desired room temperature with the TEMPERATURE buttons

(the display indicates the setting).

The temperature setting and the actual room temperature may vary

depending on conditions.

START

STOP

1

2

3

Set the desired FAN SPEED with the (FAN SPEED) button (the

display indicates the setting).

AIR PURIFYS

only have to press the

(AUTO)

(HIGH)

(MED)

(LOW)

(SILENT)

of

– 12 –

HEATING OPERATION

ƽ Use the device for heating when the outdoor temperature is under 21°C.

When it is too warm (over 21°C), the heating function may not work in order to protect the device.

ƽ In order to maintain reliability of the device, please use this device when outdoor temperature is above -15°C.

Press the MODE selector button so that the display indicates

(HEAT).

Set the desired FAN SPEED with the (FAN SPEED) button

(the display indicates the setting).

Set the desired room temperature with the TEMPERATURE buttons

(the display indicates the setting).

The temperature setting and the actual room temperature may

vary depending on conditions.

Press the

(START/STOP) button. Heating operation starts with

a beep. Press the button again to stop operation.

Ƶ As the settings are stored in the memory of the remote controller, you only

have to press the (START/STOP) button next time.

Ƶ During AUTO fan, the fan speed automatically changes as below:

ƽWhen the difference between room temperature and setting temperature

is large, fan starts to run at HI speed.

ƽAfter room temperature reaches the preset temperature, fan speed

will be changed to lower speed to obtain optimum room temperature

condition for natural healthy heating.

START

STOP

Ƶ Defrosting

Defrosting will be performed about once an hour when frost forms on the heat exchange of the outdoor unit,

for 5~10 minutes each time.

During defrosting operation, the operation lamp blinks in a cycle of 3 seconds on and 0.5 second off.

The maximum time for defrosting is 20 minutes.

However, if the indoor unit is connected to multi type outdoor unit, the maximum time for defrosting is 15 minutes.

(If the piping length used is longer than usual, frost is likely to form.)

1

2

3

AIR PURIFYS

(AUTO)

(HIGH)

(MED)

(LOW)

(SILENT)

– 13 –

ENGLISH

DEHUMIDIFYING OPERATION

Ƶ Dehumidifying Function

ƽ When the room temperature is higher than the temperature setting: The device will dehumidify the

room, reducing the room temperature to the preset level.

When the room temperature is lower than the temperature setting: Dehumidifying will be performed at

the temperature setting slightly lower than the current room temperature, regardless of the temperature

setting.

ƽ The preset room temperature may not be reached depending on the number of people present in the

room or other room conditions.

Set the desired room temperature with the ROOM

TEMPERATURE setting buttons (the display indicates the

setting).

The range of 20-26 C is recommended as the room

temperature for dehumidifying.

Press the (START/STOP) button. Dehumidifying operation

starts with a beep. Press the button again to stop operation.

ƵAs the settings are stored in the memory of the remote controller, you only

have to press the

(START/STOP) button next time.

START

STOP

Press the MODE selector button so that the display

indicates

(DEHUMIDIFY).

The fan speed is set at LOW.

Press

(FAN SPEED) button to select SILENT or LOW fan

speed.

Use the device for dehumidifying when the room temperature is over 16°C.

When it is under 15°C, the dehumidifying function will not work.

1

2

AIR PURIFYS

Ý

– 14 –

COOLING OPERATION

Use the device for cooling when the outdoor temperature is -10~ 43°C.

If indoors humidity is very high (80%), some dew may form on the air outlet grille of the indoor unit.

Press the MODE selector button so that the display indicates

(COOL).

Set the desired F

AN SPEED with the

(FAN SPEED) button (the

display indicates the setting).

Set the desired room temperature with the TEMPERATURE buttons

(the display indicates the setting).

The temperature setting and the actual room temperature may vary

depending on conditions.

Press the

(START/STOP) button. Cooling operation starts with a

beep. Press the button again to stop operation. The cooling function

does not start if the temperature setting is higher than the current

room temperature (even though the

(OPERATION) lamp lights).

The cooling function will start as soon as user set the temperature

below the current room temperature.

Ƶ

As the settings are stored in the memory of the remote controller, you only

have to press the

(START/STOP) button next time.

Ƶ During AUTO fan, the fan speed automatically changes as below:

ƽ When the difference between room temperature and setting tem-

perature is large, fan starts to run at HI speed.

ƽ After room temperature reaches the preset temperature, fan speed

will be changed to lower speed to obtain optimum room temperature

condition for natural healthy cooling.

START

STOP

1

3

AIR PURIFYS

(AUTO)

(HIGH)

(MED)

(LOW)

(SILENT)

2

– 15 –

ENGLISH

FAN OPERATION

User can use the device simply as an air circulator.

START

STOP

1

2

Press the MODE selector so that the display indica set

(FAN).

Press the

(START/STOP) button. Fan operation starts with

a beep. Press the button again to stop operation.

AIR PURIFYS

Set the desired FAN SPEED with the (FAN SPEED) button

(the display indicates the setting).

(HIGH)

(MED)

(LOW)

(SILENT)

– 16 –

AIR PURIFYING OPERATION

Negative ions are gener at ed by the plasma electrode in the indoor unit.

Dust, mold and odour particles are captured by negative ions and are caught by the stainless pre-filter.

Press the

“ ” is displayed on the LCD.

Press (AIR PURIFYING) button again.

Press (START/STOP) button. Or

AUTO SWING OPERATION

Vertical

about 15

about 60

about 45

about 30

When cooling,

dehumidifying

When heating

AIR PURIFYS

(AIR PURIFYING) button during operation.

Ƶ To start AIR PURIFYING operation

“ ” disappears from the LCD.

ƽ

Ƶ To start Vertical Auto Swing

Ƶ To cancel Vertical Auto Swing

NOTE

ƽ



During cooling and dehumidifying operation, do not keep

the deflectors swinging or in the lower position (in the case

of vertical auto swing) for a long time. It may cause dew

condensation on the deflectors.

Press (AUTO SWING (VERTICAL)) button. The

deflector(s) will start to swing up and down.

is displayed on the LCD.

Press (AUTO SWING (VERTICAL)) button again. The

deflector(s) will stop in the current position.

disappeared from the LCD.

ƽ

Ƶ To cancel AIR PURIFYING operation

– 17 –

ENGLISH

POWERFUL OPERATION

ƽ By pressing (POWERFUL) button during AUTO, HEATING, DEHUMIDIFYING, COOLING or FAN

operation, the air conditioner performs at the maximum power.

ƽ During POWERFUL operation, cooler or warmer air will be blown out from indoor unit for COOLING

or HEATING operation respectively.

Ƶ To start POWERFUL operation

Ƶ To cancel POWERFUL operation

Press (POWERFUL) button during operation.

ƽ

“

” is displayed on the LCD.

POWERFUL operation ends in 20 minutes. Then the system

automatically operates with the previous settings used before

POWERFUL operation.

Press

(POWERFUL) button again.

POWERFUL operation stops.

“

” disappears from the LCD.

1

NOTE

ƽ When SLEEP mode, ECO mode, SILENT mode or LEAVE HOME mode is selected, POWERFUL

operation is cancelled.

ƽ During POWERFUL operation, capacity of the air conditioner will not increase

– if the air conditioner is already running at maximum capacity.

– just before defrost operation (when the air conditioner is running in HEATING operation).

ƽ After auto restart, POWERFUL operation is cancelled and previous operation shall start.

For multi model connections, POWERFUL operation may not function depending on operation conditions.

AIR PURIFYS

ƽ

Press (START/ STOP) button.Or

ƽ

– 18 –

SILENT OPERATION

ƽ By pressing (SILENT) button during AUTO, HEATING, DEHUMIDIFYING, COOLING or FAN

operation, the fan speed will change to ultra slow.

Ƶ To start SILENT operation

Ƶ To cancel SILENT operation

Press (SILENT) button during operation.

ƽ

“ ” is displayed on the LCD. Fan speed will be ultra

slow.

ƽ Press (START/STOP) button. Or

ƽ

Press (SILENT) button again or (FAN SPEED)

button.

Fan speed will return to previous fan speed before SILENT

operation starts.

SILENT operation stops.

“

” disappears from the LCD.

1

NOTE

ƽ When POWERFUL operation is selected, SILENT operation is cancelled. Fan speed will return to

previous fan speed before SILENT operation.

ƽ After auto restart, SILENT operation is cancelled. Fan speed will return to previous fan speed before

SILENT operation.

ƽ During any operation with fan speed (SILENT), if press (SILENT) button, fan speed will

not change.

AIR PURIFYS

– 19 –

ENGLISH

ECO OPERATION

ƽ By pressing the (ECO) button during AUTO, HEATING,

DEHUMIDIFYING or COOLING operation, the air conditioner

performs the "ECO" operation.

1

Ƶ To start ECO operation

ƵTo cancel ECO operation

Press (ECO) button during operation.

ƽ

“ ” is displayed on the LCD.

Energy saving operation will start by changing the set

temperature higher or lower automatically and reducing operation

power consumption. This function may vary based on the

connected outdoor unit.

ƽ Press (START/STOP) button. Or

ƽ Press (ECO) button again.

“

” disappears from the LCD.

NOTE

ƽ ECO function will not be effective when power consumption is low.

ƽ By pressing (POWERFUL) button, ECO operation is cancelled.

ƽ After auto restart, ECO operation is cancelled and previous operation mode shall start.

ƽ For multi model connections, energy saving operation shall start only by changing set temperature higher

or lower automatically. However, effectiveness of ECO depends on operation conditions.

AIR PURIFYS

ECO operation is an energy saving function by changing set temperature automatically and by limiting the

ma x imum power consumption value.

– 20 –

LEAVE HOME(LH) OPERATION

Ƶ To start LEAVE HOME operation

Press

(LEAVE HOME) button during stop or operation.

ƽ

Room temperature is set at 10°C and heating operation starts.

“

”, “ ”, “ ”, “ ” is displayed on the LCD.

Press

(LEAVE HOME) button during stop or operation.

Room temperature is set at 10°C and heating operation starts.

“

”, “ ”, “ ”, “ ” is displayed on the LCD.

ƽ Set number of operation days (1 to 99 days), if needed.

Press

(TIME) button to select number of days.

Number of days blink.

* Press “

(UP)” to set number of days from 1 day, 2 days, 3

days ..... 98 days, 99 days, 1 day and so on.

* Press “

(DOWN)” to set number of days from 99 days, 98

days, 97 days .... 3 days, 2 days, 1 day, 99 days and so on.

* Number of day is counted when clock indicates 0:00.

ƽ Press (SEND) button to con firm number of operation

days. Display for number of operation days will stop blinking.

ƽPress (CANCEL) button to reset number of operation

days or to have continuous operation.

1

Ƶ To cancel LEAVE HOME operation

ƽ Press (START/STOP) button. Or

ƽ

Press

(LEAVE HOME) button again.

ƽ Change to other operation mode by pressing (MODE) button.

NOTE

ƽ After reaching the set number of operation days for Leave Home or by pressing the (Leave Home) button again,

ƽ During Leave Home operation, fan speed and horizontal air deflector position cannot be changed.

ƽ By pressing (Leave Home) button, implementation of Weekly Timer or Once Timer only Timer is cancelled.

ƽ In case of power supply shut down, after autorestart, all setting for number of days operation will be reset and unit

shall be in continuous operation.

ƽ

or AUTO mode, Leave Home operation cannot operate even though it is possible to set Leave Home operation.

In order to start Leave Home operation, all rooms must stop its operation. Then, press (LEAVE HOME) button to

operate Leave Home operation.

ƽ For multi connections, when all rooms are running HEATING operation, it is possible to operate Leave Home operation

by pressing the (LEAVE HOME) button.

ƽ For multi connections, if two or more rooms are set to operate Leave Home operation, the capability to reach the

set temperature at 10°C may not possible. In addition, this also depends on outdoor temperature.

Continuous operation

Day timer operation

AIR PURIFYS

Prevent the room temperature from falling too much by setting temperature automatically when no one is at home.

This operation is able to operate by" Continuous operation" or " Day timer operation" . Please use " Day timer operation"

to set the number of days up to 99 days.

the unit will operate in previous mode.

Option 1. Continuous operation.

Option 2. Day timer operation.

10°C

ƽ

Return to previous operation mode. Or

oFor multi connections, when each room is running in different operation mode such as FAN only, COOLING, DEHUMIDIFYING

POWERFUL,SILENT and ECO operations are not applicable during Leave Home.

ƽ

La pagina sta caricando ...

Hitachi RAK-50PXA Istruzioni per l'uso

Questo manuale è adatto anche per

Hitachi RAK-50PXA Istruzioni per l'uso

in altre lingue

Documenti correlati

Altri documenti