Avent SCF355/00 Manuale utente

4213 354 36477

SCF355

5

9

13

2

6

10

14

3

7

11

15

4

8

12

16

1

SCF355

ENGLISH 6

ESPAÑOL ARGENTINA 17

ITALIANO 29

6

General description (Fig. 1)

1. Bottle warmer

2. Light

3. Settings knob

4. O setting

5. Defrost setting

6. Keep warm setting

7. Express milk warming setting for contents up to

180ml/6oz

8. Food warming setting

9. Express milk warming setting for contents over and

including 180ml/6oz

Important

To fully benet from the support that Philips

oers, register your appliance at

www.philips.com/welcome.

Read this user manual carefully before you

use the bottle warmer and save it for future

reference.

Danger

- Do not immerse the cord, plug or

appliance in water or other liquid.

Warning

- Only use the appliance indoors.

- Do not let the mains cord hang over the

edge of a table or worktop. Excess cord

can be stored in the base of the bottle

warmer.

- Keep the mains cord away from hot

surfaces.

ENGLISH

7

- Only connect the appliance to an earthed

wall socket. Always make sure that the

plug is inserted into the wall socket

properly.

- Check if the voltage indicated on the

bottom of the appliance corresponds to

the local mains voltage before you

connect the appliance.

- If you need to use an extension cord,

make sure it is an earthed extension cord

with a rating of at least 13 amperes.

- Do not use the appliance if the plug, the

mains cord or the appliance itself is

damaged. If the mains cord

is damaged,

you must have it replaced by Philips,

a service centre authorised by Philips or

similarly qualied persons in order to

avoid a hazard.

- Do not place the appliance on or near a

hot gas or electric cooker, or in a heated

oven.

- This appliances can be used by persons

with reduced physical, sensory or mental

capabilities or lack of experience and

knowledge if they have been given

supervision or instruction concerning use

of the appliance in a safe way and

understand the hazards involved.

ENGLISH

8

- Cleaning and user maintenance shall not

be made by children.

- This appliance shall not be used by

children. Keep the appliance and its cord

out of reach of children.

- Children shall not play with the appliance.

- Do not spill water on the mains plug.

- Only use the appliance as described in

the user manual to avoid potential injury

due to misuse.

- Do not preheat the appliance.

- Always place a fully assembled bottle

with cap in the bottle warmer before you

add water.

- Make sure you add water before you

switch on the bottle warmer.

- Hot water can cause serious burns. Be

careful when the bottle warmer contains

hot water.

- The accessible surfaces of the appliance

may become hot during use and are

subject to residual heat after use.

- Do not move the appliance when it

contains hot water.

- When the food or milk has reached the

required temperature, remove the bottle

or container from the bottle warmer. If you

leave food or milk in the bottle warmer,

ENGLISH

9

the temperature of the food or milk

increases.

- Always check the food temperature

before you feed your child.

Caution

- This appliance is intended to be used in

household and similar applications such

as farm houses, bed and breakfast type

environments, sta kitchen areas in

shops, oces and other working

environments, and by clients in hotels,

motels and other residential type

environments.

- Unplug the appliance when it is not in

use.

- The surface of the heating element is

subject to residual heat after use.

- Let the appliance cool down before you

clean it.

- Follow the descaling instructions to avoid

irreparable damage.

-

Do not try to open or repair the appliance

yourself. You can contact the Philips

Consumer Care Centre in your country (see

www.philips.com/support)

.

- The food should not be heated for too

long.

ENGLISH

ENGLISH10

You can nd the production date code YYWW in the cord

storage compartment in the base of the bottle warmer.

Electromagnetic elds (EMF)

This Philips appliance complies with all applicable standards

and regulations regarding exposure to electromagnetic elds.

Using the bottle warmer

With this bottle warmer, you can safely warm all Philips Avent

feeding bottles and milk/baby food in containers and other

baby food jars.

Note: Philips Avent breast milk bags and Philips Avent

2oz/60ml bottles cannot be used in this bottle warmer.

Explanation of settings

- O setting: The bottle warmer is switched o and the light

is o. On every other setting, the appliance is switched on

and the light is lit (Fig. 2).

-

Express milk warming setting for contents up to 180ml/6oz:

Select this setting when you want to quickly warm a bottle of

milk with a content up to 180ml/6oz.

The bottle has to be taken out immediately after warming to

the right temperature, otherwise the milk will be overheated.

- Food warming setting: Select this setting when you want

to warm a container/jar of baby food.

- Express milk warming setting for contents over and

including 180ml/6oz:

Select this setting when you want to quickly warm a bottle

of milk with a content over and including 180ml/6oz.

The bottle needs to be taken out immediately after

warming to the right temperature, otherwise the milk will be

overheated.

- Keep warm setting: Milk is warmed at a slower speed and

be kept at right temperature.

- Defrost setting: Defrost a bottle/container of milk/baby

food to liquid state. No warming occurs.

ENGLISH 11

Using the bottle warmer with express milk warming

setting

1 Put the mains plug in the wall socket (Fig. 3).

2 Place a bottle in the bottle warmer (Fig. 4).

3 Fill the bottle warmer with drinking water up to the level

of the milk in the bottle. In case of large amounts of milk,

the maximum level of water is approximately 1 cm below

the top of the bottle warmer. An accurate water level

ensures correct warming performance (Fig. 5).

4 Select the desired setting based on the milk volume. See

the express warming reference table at the end of this

chapter to check how long the milk needs to be warmed

in the selected setting (Fig. 6).

Note: The speed of warming milk depends on the amount of

the milk warmed and on its initial temperature, i.e. room

temperature (20°C) or fridge temperature (5°C).

5 The orange light goes on when you select a setting. This

indicates that the bottle warmer is on (Fig. 7).

Note: Whilst warming the milk circulates and heats evenly.

6 Check the express warming reference table for the time

required to warm the milk. Remove the bottle from the

bottle warmer after the time indicated in the express

warming reference table has passed (Fig. 8).

Tip: When you nd the milk is not warm enough, you can

place the bottle back into the appliance for a maximum of

30 seconds of extra warming. This will create a slightly

warmer result but without overheating.

Caution: If you leave the bottle in the bottle warmer longer

than the time indicated in the settings table, the milk may

become overheated.

Note: If you overheat breast milk, valuable nutrients and

vitamins may be lost.

7 Always check the temperature before you feed your baby.

Gently shake the bottle or milk storage container and check

the temperature of the milk by sprinkling a few drops on the

inside of your wrist (Fig. 9).

8 Turn the knob back to the ‘o’ position (Fig. 10).

Caution: The water in the bottle warmer might be hot after

nishing warming milk / baby food. Be careful that hot water

can cause serious burns.

If you do not turn the knob back to the ‘o’ position, the

water keeps heating up and will reach a very high

temperature.

Express warming reference table

ml/oz min min

5°C/40°F 20°C/70°F

60 ml/2 oz-90 ml/3 oz 4.5 3.0

90 ml/3 oz-110 ml/3.7 oz 5.5 3.0

125 ml/4 oz-150 ml/5 oz 3.5 3.0

180 ml/6 oz-210 ml/7 oz 5.5 4.0

240 ml/8 oz-260 ml/9 oz 7.0 4.5

290 ml/10 oz-330 ml/11 oz 7.5 5.0

Note: The indicated warming times are based on Philips

Avent Classic and Natural PP bottle ranges. Be aware that

warming timings of Philips Avent standard bottles and glass

bottles deviate from these indications. The characteristics of

bottles such as material or thickness may also impact the

warming times, therefore it may take less time to warm a

larger volume of milk.

Note: The milk may feel cool to you, but for a newborn baby

its temperature is very pleasant.

ENGLISH12

Using the bottle warmer to warm baby food

1 Follow the same steps as indicated in the previous

paragraph.

2 Make sure to stir the baby food during warming as it

does not circulate automatically. Be careful not to burn

your ngers when holding the container/jar while stirring

(Fig. 11).

After warming test the baby food with a spoon to ensure it is

not too hot. If the baby food is not warm enough, put the

container back into the bottle warmer and warm the baby food

until it has the desired temperature.

Note: Due to the high variety of baby food consistencies, it

is strongly recommended to continuously stir and check

while you are warming the baby food for an optimal result.

Note: Due to the high variety of baby food consistencies, it

is not possible to indicate warming timings for baby food.

Using the keep warm setting to warm milk

1 Put the mains plug in the wall socket (Fig. 3).

2 Place the bottle or container in the bottle warmer (Fig. 4).

3 Fill the bottle warmer with drinking water up to the

level of the milk in the bottle/container. In case of

large amounts of milk, the maximum level of water is

approximately 1 cm below the top of the bottle warmer

(Fig. 5).

4 Select the position of keep warm (Fig. 6).

At this setting, you can warm your milk at a slow pace and

keep it warm at the right end temperature. E.g. to warm a

bottle of 4oz milk starting from room temperature, it will

take 15-20min. The warming time may be longer or shorter

depends on the milk volumes and starting temperature.

Note: Philips Avent recommends to feed your baby as

soon as possible after the milk is warmed. We advise not to

reheat the milk after it has cooled down again.

ENGLISH 13

14

Note: Always check the temperature before you feed your

baby (Fig. 9).

5 Turn the knob back to the ‘o’ position when the bottle/

container is removed from the bottle warmer (Fig. 10).

Using the bottle warmer with defrost setting

1 Put the mains plug in the wall socket (Fig. 3).

2 Place the bottle or container in the bottle warmer (Fig. 4).

3 Fill the bottle warmer with drinking water up to the level

of the milk/baby food in the bottle/container. In case of

large amounts of milk/baby food, the maximum level of

water is approximately 1 cm below the top of the bottle

warmer (Fig. 5).

4 Select the position of defrost (Fig. 6).

At this setting, your frozen milk/baby food can be defrosted

till liquid state.

For frozen milk, check the warming reference table for the

expected defrost timings, as indication one small and one

larger milk volume are included in the table. After your milk is

defrosted, choose express warming setting or keep warming

setting to warm your milk. Please refer to the previous

chapters for usage instructions. Consider the start

temperature of your milk around fridge temperature for the

warming timings as rough guideline.

ml/oz hours

60 ml/2 oz-90 ml/3 oz 1-1.5

180 ml/6 oz-210 ml/7 oz 1.5-2.5

5 You may also defrost baby food in Philips Avent food

container by this setting. After your baby food is

defrosted, choose food warming setting to warm it.

Please refer to the previous chapter for usage instruction.

ENGLISH

15

Note: Due to the high variety of baby food consistencies, it

is strongly recommended to continuously stir and check

while you are defrosting the baby food for an optimal result.

Note: Due to the high variety of baby food consistencies, it

is not possible to indicate warming timings for baby food.

Cleaning and descaling

Cleaning

1

After each use, unplug the bottle warmer and let it cool

down (Fig. 12).

2 Remove the water from the bottle warmer for hygienic

reasons (Fig. 13).

3

Wipe the outside and inside of the bottle warmer with a

moist cloth

(Fig. 14).

Do not use abrasive, anti-bacterial cleaning agents,

chemical solvents or sharp tools to clean the bottle warmer.

Note: If you used the bottle warmer to warm containers with

baby food, make sure that no spilled baby food remains on

the bottom of the bottle warmer.

Descaling

It is recommended to descale the bottle warmer every four

weeks to ensure it continues to work eciently.

1 Mix 50ml/1.7oz of white vinegar with 100ml/3.4oz of cold

water to descale the bottle warmer. Switch on the bottle

warmer, select the milk warming setting for contents

under 180ml/6oz and let the appliance operate for 10

minutes. Leave the solution in the bottle warmer until all

scale has dissolved (Fig. 15).

Note: You can also use citric acid based descalers.

Note: Do not use other types of descalers.

2 Unplug the bottle warmer before you empty it (Fig. 12).

ENGLISH

ENGLISH16

3

Empty the bottle warmer and rinse its inside thoroughly. If

you still see traces of scale after rinsing, repeat the

descaling procedure (Fig. 13).

Recycling

- This symbol means that this product shall not be disposed

of with normal household waste (2012/19/EU). (Fig. 16)

- Follow your country’s rules for the separate collection of

electrical and electronic products. Correct disposal helps

prevent negative consequences for the environment and

human health.

Guarantee and support

If you need information or support, please visit

www.philips.com/support or read the separate worldwide

guarantee leaet.

ESPAÑOL ARGENTINA 17

Descripción general (Fig. 1)

1. Calentador de mamaderas

2. Luz

3. Perilla de ajustes

4. Modo de apagado

5. Posición para descongelar

6. Perilla de conservación del calor

7. Ajuste rápido para calentar leche para contenidos de

hasta 180 ml/6 oz

8. Modo para calentar comida

9. Ajuste rápido para calentar leche para contenidos de

180 ml/6 oz o más

Importante

Para sacar el mayor partido a la asistencia

que Philips le ofrece, registre el aparato en

www.philips.com/welcome.

Antes de usar el calientabiberones, lea

atentamente este manual de usuario y

consérvelo por si necesitara consultarlo en

el futuro.

Peligro

- No sumerja el cable, el enchufe ni el

aparato en agua u otros líquidos.

Advertencia

- Utilice el aparato solo en interiores.

- No deje que el cable de alimentación

cuelgue del borde de la mesa o encimera.

El cable sobrante puede guardarse en la

base del calientabiberones.

18

- Mantenga el cable de alimentación

alejado de supercies calientes.

- El aparato únicamente debe conectarse a

un enchufe de pared con toma de tierra.

Asegúrese siempre de que la clavija esté

bien insertada en la toma de corriente.

- Antes de enchufar el aparato, compruebe

si el voltaje indicado en la parte inferior

del mismo se corresponde con el voltaje

de red local.

- Si necesita utilizar un cable alargador,

asegúrese de que el cable dispone de

toma de tierra con una clasicación

mínima de 13 amperios.

- No utilice el aparato si el enchufe, el cable

de alimentación o el aparato están

dañados. Si el cable de alimentación está

dañado, debe ser sustituido por Philips o

por un centro de servicio autorizado por

Philips, con el n de evitar situaciones de

peligro.

- No coloque el aparato sobre o cerca de

una cocina de gas o eléctrica caliente, o un

horno caliente.

- Este artefacto lo pueden utilizar personas

con capacidad física, psíquica o sensorial

reducida y quienes no tengan los

conocimientos ni experiencia necesarios

ESPAÑOL ARGENTINA

19

si han sido supervisados o instruidos

acerca del uso del aparato de forma

segura y entienden los riesgos que

conlleva su uso.

- La limpieza y el mantenimiento que

realiza el usuario no pueden ser

realizados por niños.

- Este artefacto no debe ser utilizado por

los niños. Mantenga el artefacto y el

cable fuera del alcance de los niños.

- No permita que los niños jueguen con el

aparato.

- No derrame agua sobre la clavija.

- Utilice únicamente el aparato como se

describe en el manual de usuario para

evitar posibles lesiones debido a un uso

incorrecto.

- No precaliente el aparato.

- Coloque siempre el biberón totalmente

montado con tapa en el

calientabiberones antes de añadir agua.

- Asegúrese de añadir el agua antes de

encender el calientabiberones.

- El agua caliente puede causar

quemaduras graves. Tenga cuidado

cuando el calientabiberones contenga

agua caliente.

ESPAÑOL ARGENTINA

20

- Las supercies accesibles del aparato

pueden calentarse durante el uso y están

sujetas a calor residual después de su

uso.

- No mueva el aparato cuando contenga

agua caliente.

- Cuando la comida o la leche haya

alcanzado la temperatura necesaria, quite

el biberón o el recipiente del

calientabiberones. Si deja la comida o la

leche en el calientabiberones, la

temperatura de la comida o la leche

aumentará.

- Compruebe siempre la temperatura de la

comida antes de empezar a dar de comer

al niño.

Precaución

- Este aparato está diseñado para utilizarlo

en entornos domésticos o similares

como: viviendas de granjas, hostales en

los que se ofrecen desayunos, zona de

cocina en tiendas, ocinas y

otros

entornos laborales, y por clientes de

hoteles,

moteles y entornos residenciales

de otro tipo.

- Desenchufe el aparato cuando no lo

utilice.

ESPAÑOL ARGENTINA

21

- La supercie de la resistencia se somete

a calor residual después de su uso.

- Deje que el aparato se enfríe antes de

guardarlo.

- Siga las instrucciones de eliminación de

los depósitos de cal para evitar daños

irreparables.

- No intente abrir ni reparar el aparato por

su cuenta. Puede ponerse en contacto

con el Servicio de Atención al Cliente de

Philips de su país (consulte

www.philips.com/support).

- Los alimentos no se deben calentar

durante mucho tiempo.

Campos electromagnéticos (CEM)

Este aparato de Philips cumple los estándares y las

normativas aplicables sobre exposición a campos

electromagnéticos.

Uso del calentador de mamaderas

Con este calentador de mamaderas puede calentar de

manera segura todas las mamaderas y los recipientes para

comida o leche de Philips Avent u otros recipientes para

comida de bebé.

Nota: Las bolsas para leche materna de Philips Avent y los

biberones Philips Avent de 60 ml/2 oz no se pueden utilizar

en este calentador de biberones.

Explicación de las posiciones

- Ajuste de apagado: el calentador de biberones y la luz se

apagan. En cualquier otro ajuste, el artefacto se enciende

y la luz también (Fig. 2).

ESPAÑOL ARGENTINA

22

-

Ajuste rápido para calentar leche para contenidos de

hasta 180 ml/6 oz: seleccione este ajuste cuando desee

calentar rápidamente un biberón con un contenido de

hasta 180 ml/6 oz.

El biberón se debe quitar de inmediato después de

calentarlo a la temperatura adecuada, de lo contrario, la

leche se sobrecalentará.

- Ajuste para calentar comida: seleccione este ajuste

cuando desee calentar un recipiente o un tarrito de

alimento para bebés.

- Ajuste rápido para calentar leche para contenidos de

180 ml/6 oz o más:

seleccione este ajuste cuando desee calentar

rápidamente un biberón con contenido de 180 ml/6 oz o

más.

El biberón se debe quitar de inmediato después de

calentarlo a la temperatura adecuada, de lo contrario, la

leche se sobrecalentará.

- Ajuste de conservación del calor: la leche se calienta a

una velocidad más lenta y se mantiene a la temperatura

adecuada.

- Ajuste para descongelar: descongele un biberón o un

recipiente de alimento para bebés hasta que su

contenido alcance un estado líquido. No se produce

calentamiento.

Uso del calentador de biberones con el ajuste rápido

para calentar leche

1 Enchufe el aparato al enchufe de pared (Fig. 3).

2 Coloque una mamadera en el calentador de

mamaderas (Fig. 4).

3

Llene el calientabiberones con agua potable hasta el nivel

de leche del biberón. En caso de grandes cantidades de

leche, el nivel máximo de agua es de aproximadamente

1 cm por debajo de la parte superior del calentador de

biberones. Un nivel de agua preciso garantiza el

funcionamiento correcto del calentador (Fig. 5).

ESPAÑOL ARGENTINA

La pagina si sta caricando...

Avent SCF355/00 Manuale utente

Questo manuale è adatto anche per

Avent SCF355/00 Manuale utente

in altre lingue

Documenti correlati

Altri documenti