ProLights SUNBAR2500MAX Manuale utente

USER MANUAL

MANUALE UTENTE

EN - IT

STROBO LED BAR

SUNBAR2000FC

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the

characteristics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

REV.001-02/18

1

SUNBAR2000FC

Packing content

• SUNBAR2000FC

• Mount bracket

• User manual

TABLE OF CONTENTS

Safety

General instructions

Warnings and installation precautions

1 Introduction

1. 1 Description

1. 2 Technical specications

1. 3 Operating elements and connections

2 Installation

2. 1 Mounting

3 Functions and settings

3. 1 Operation

3. 2 Basic

3. 3 Menu structure

3. 4 Linking

3. 5 DMX address

3. 6 DMX mode

3. 7 DMX addressing

3. 8 Ethernet

3. 9 ID and RDM

3. 10 Temperature unit

3. 11 Screen

3. 12 Fixture

3. 13 Fixture information

3. 14 Master/Slave

3. 15 Sequence

3. 16 Static mode

3. 17 Connection of the DMX line

3. 18 Construction of the DMX termination

3. 19 DMX control

3. 20 Pixel layouts

4 Maintenance

4. 1 Maintenance and cleaning the unit

4. 2 Fuse replacement

4. 3 Trouble shooting

2

3

5

6

7

8

11

12

13

14

15

16

17

26

27

28

SUNBAR2000FC

2

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

SAFETY

General instruction

• The products referred to in this manual conform to the European Community Directives and are there-

fore marked with .

• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.

Never make any modications on the unit not described in this instruction manual, otherwise you will

risk an electric shock.

• Connection must be made to a power supply system tted with ecient earthing (Class I appliance ac-

cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units

from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• The connection to the main network of electric distribution must be carried out by a qualied electrical

installer. Check that the main frequency and voltage correspond to those for which the unit is designed

as given on the electrical data label.

• This unit is not for home use, only professional applications.

• Never use the xture under the following conditions:

- in places wet;

- in places subject to vibrations or bumps;

- in places with an ambient temperature of over 45°C.

• Make certain that no inammable liquids, water or metal objects enter the xture.

• Do not dismantle or modify the xture.

• All work must always be carried out by qualied technical personnel. Contact the nearest sales point for

an inspection or contact the manufacturer directly.

• If the unit is to be put out of operation denitively, take it to a local recycling

plant for a disposal which is not harmful to the environment.

Warnings and installation precautions

• If this device will be operated in any way dierent to the one described in this manual, it may suer

damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like

short circuit, burns, electric shock, etc.

• Before starting any maintenance work or cleaning the projector, cut o power from the main supply.

• Always additionally secure the projector with the safety rope. When carrying out any work, always com-

ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country

in which the xture’s being used.

• For inside use only. Not designed for outside use.

• The minimum distance between the xture and surrounding walls must be more than 50 cm and the

air vents at the housing must not be covered in any case.

• Install the xture in a well ventilated place.

• Keep any inammable material at a safe distance from the xture.

• The maximum temperature that can be reached on the external surface of the tting, in a thermally

steady state, is high. After power o, please cool down over 15 minutes.

• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent

that their eectiveness is impaired.

• The lamp (LED) shall be changed if it has become damaged or thermally deformed.

• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ashing light, may

trigger epileptic seizures in photosensitive persons or persons with epilepsy.

3

SUNBAR2000FC

- 1 - INTRODUCTION

1.1 DESCRIPTION

SUNBAR2000FC is an exceptionally powerful LED graphic strobe batten, featuring also as static blind-

er and ood. SUNBAR2000FC oers a exible control of beam coverage through an interchange-

able lens system, passing from 100° wide to 30° beam increasing the light intensity up to 4 time.

Available in White or Full Colour versions, and designed to deliver simply staggering light levels, this ver-

satile xture can provide an unbelievable punch over a huge area.

1.2 TECHNICAL SPECIFICATIONS

LIGHT SOURCE

• Source:1024x1 W RGBW LEDs

• CT:W: 6250 K

• Luminous Flux:Strobe without lens (peak) 126’000 lm; Static ON without lens 28’834; Strobe with lens

(peak) 46’200; Static ON with lens 27’188 lm

• Lux:(100°) 1139 lux, (30°) 4152 lux @3m Full

• Lux:(100°) 410.1 lux, (30°) 1495 lux @5m Full

• Source Life Expectancy: >30.000 h

OPTICS

• Beam Angle:without lens 100°, with lens 30 °

• Field Angle:without lens 150°, with lens 80 °

• Other:Mountable 30° lens reector plate (included)

COLOR SYSTEM

• Color Mixing: RGBW/FC

• Color Wheel: Virtual color wheel with presets

DYNAMIC EFFECTS

• Rotating Gobos: Dynamic Patterns with speed and rotation control

• Pixel Patterns: Preprogrammed dynamic and static patterns

• FX Generator: Adjustable foreground/background color, index, speed, direction

• Static Color Mode: Selection of static color

• Manual Color Mode: Manual adjustment of color

• Auto Mode: Built-in programs with execution speed adjustment

• Special Features:Multi-layer pixel FX control

BODY

• Hardware On-board: Omega sockets for quick rigging (clamp not included)

• Body: Sturdy die-cast aluminium body conceived for long-time durability

• Body Color: Black

CONTROL

• Protocols: DMX512, RDM, Art-Net, Kling-Net

• DMX Channels:from 4 ch to 87 ch

• Pixel Control:1/2/4/8/16 selectionable and controllable sections

• RDM: RDM ready for xture remote monitor and settings

SUNBAR2000FC

4

• Display: Black TFT touch display

• Firmware Upgrade: Yes, via USB-DMX interface (UPBOX1) not included

ELECTRONICS

• Dimmer: Linear 0~100% electronic dimmer

• Dimmer Curves:4 Dierent dimming curves available

• Strobe/Shutter:1-30 Hz, electronic

• Operating Temperature: -10° ~ +45°

• Selectable PWM: 400~16K Hz

ELECTRICAL

• Power Supply: 100-240V – 50/60Hz

• Power Consumption (at 230V):Strobe: 987 W Static: 600 W

• Power Consumption (at 120V):Strobe: 1065 W Static: 630 W

• Output (at 230V):3 units on a single power line

• Output (at 120V):1 units on a single power line

PHYSICAL

• Cooling: Forced air with low noise fan

• Suspension And Fixing: Hanging bracket for oor positioning with “Quick-Lock” system

• Signal Connection: 5p in/out, RJ45 in/out

• Power Connection: Seetronic Powerkon True IP65 in/out

• IP:20

• Dimensions (WxHxD):1000x75x231 mm

• Weight:9,60 kg

Fig.1

1000 231

75

Technical drawing

5

SUNBAR2000FC

Fig.2

1.3 OPERATING ELEMENTS AND CONNECTIONS

1. LED BAR

2. LOCKING KNOB for the

mounting bracket.

3. MOUNTING BRACKET

4. CONTROL PANEL with TFT

display and 4 button used

to access the control panel

functions and manage them.

5. AIR OPENING

6. DMX OUT (5-pole XLR): 1 =

ground, 2 = DMX-, 3 = DMX+, 4

N/C, 5 N/C.

7. POWER OUT (PowerCON OUT):

power output for connection of

multiple units in series.

8. EtherCON connector Signal IN/

OUT.

9. POWER IN (PowerCON IN):

for connection to a socket

(100-240V~/50-60Hz) via the

supplied mains cable.

10. DMX IN (5-pole XLR): 1 =

ground, 2 = DMX-, 3 = DMX+, 4

N/C, 5 N/C.

11. FUSE

View A View B

1

2

3

B

A

4

11

6

10

8

7

9

5 5

SUNBAR2000FC

6

- 2 - INSTALLATION

2.1 MOUNTING

The SUNBAR2000FC may be set up on a solid and even surface. By means of the xing facilities of the

baseplate, the unit can also be mounted upside down to a cross arm. The base plate is shown in g.3. For

xing, stable mounting clips are required. According to the gure, the bolts of the brackets are placed into

the openings provided in the base plate and turned clockwise until they lock (to the stop). Always ensure

that the unit is rmly xed to avoid vibration and slipping while operating. The mounting place must be of

sucient stability and be able to support a weight of 10 times of the unit’s weight. When carrying out any

installation, always comply scrupulously with all the regulations (particularly regarding safety) currently

in force in the country in which the xture’s being used. Always additionally secure the projector with the

safety rope from falling down. For this purpose, fasten the safety rope at a suitable position so that the

maximum fall of the projector will be 20 cm.

Fig.3

SAFETY

CABLE

OMEGA

BRACKETS

7

SUNBAR2000FC

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

Connect the supplied main cable to a socket (100-240V~/50-60Hz). The unit will run built-in program to

reset all motors to their home position. Shortly after that the SUNBAR2000FC is ready for operation. To

switch o, disconnect the mains plug from the socket. For a more convenient operation it is recommend-

ed to connect the unit to a socket which can be switched on and o via light switch.

3.2 BASIC

The control panel of SUNBAR2000FC has a display and 4 buttons for the complete programming and

management of the projector menu (g.4).

UP DOWN MENU ENTER

Increases the value

displayed or passes to

the previous item in a

menu

Decreases the value

displayed or passes to

the next item in the

menu

To enter in the main

menù or to return to the

top level

Conrms the displayed

value, or activates the

displayed function, or

enters the successive

menu

Fig.4 - Functions of the buttons and display icons

CONNECT SETUP ADVANCED INFORMATION STAND ALONE

SUNBAR2000FC

8

3.3 MENU STRUCTURE

MENU

1 CONNECT

ð

DMX Address

ð

Value (1-512)

DMX Mode

ð

Basic

ð

Static

Strobe

ð

R=0~255

G=0~255

B=0~255

W=0~255

Pixels

RGBW StRoBe

Pixels

ð

1 px

2 px

4 px

8 px

16 px

AdvAnced

ð

AdvAnced 1

A

dvAnced 2

A

dvAnced 3

A

dvAnced 4

e

theRnet

ð

pRotocol

ð

KlinG-net

only ARt-net

ARt-net+dMx

S

uBnet

ð

0-15

univeRSe

ð

0-15

StARt chAnnel

ð

1-512

ip AddReSS

ð

2/10

etheRnet to dMx

ð

no

yeS

RdM id

ð

15d0020d****

2 SETUP

ð

Temperature Unit

ð

° C

° F

Screen

ð

Back Light

ð

ON

10 S

20 S

30 S

Flip Display

ð

no

yeS

Key Lock

ð

no

yeS

9

SUNBAR2000FC

MENU

ð

Fixture

ð

White BAlAnce

ð

O

MAnuAl Red

GReen

Blue

White

ð

<125-255>

diMMeR Mode

ð

off

diMMeR 1

d

iMMeR 2

d

iMMeR 3

f

An Mode

ð

Auto

hiGh

3 ADVANCED

ð

LED Frequency

ð

400Hz

600Hz

800Hz

1200Hz

2000Hz

4000Hz

8000Hz

16KHZ

ð

fActoRy ReloAd

ð

no

yeS

MAppinG RotAtion

ð

no

yeS

4 INFORMATION

ð

fixtuRe tiMe

ð

0-9999

teMpeRAtuRe

ð

58 °c

fAnS Speed

ð

**%

SoftWARe veRSion

ð

diSp-v1.0

ctR1-net-v1.0

ctR2-led-v1.0

5 STAND ALONE

ð

MASteR/SlAve

ð

MASteR

SlAve

Sequence

ð

ShoW 1

S

hoW 2

S

hoW 3

……

ShoW 16

S

hoW 17

S

hoW 18

S

hoW 19

S

hoW 20

S

hoW 21

ð

Speed

ð

1-100

ð

foReGRound

ð

BlAcK

R

G

B

W

GB

RB

RG

SUNBAR2000FC

10

MENU

RGB

RW

GW

BW

RGW

RBW

GBW

RGBW

ShoW 22

S

hoW 23

ð

BAcK-

GRound

ð

BlAcK

R

G

B

W

GB

RB

RG

RGB

RW

GW

BW

RGW

RBW

GBW

RGBW

ð

StAtic

ð

fixed coloR

ð

R

G

B

W

GB

RB

RG

RGB

RW

GW

BW

RGW

RBW

GBW

RGBW

ð

MAnuAl coloR

ð

Red

Green

Blue

White

ð

<000-255>

11

SUNBAR2000FC

3.4 LINKING

Several units may be interconnected in order to control all further slave units to the same eect of the

master unit.

1. Connect the DMX OUT of the master unit via 5-pole XLR cable to the DMX IN of the rst slave unit.

2. Connect the DMX OUT of the rst slave unit to the DMX IN of the second slave unit, etc. until all units

are connected in a chain.

3.5 DMX ADDRESS

To enter the DMX mode, follow these steps:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Connect icon, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select the Address and press the ENTER key.

• Press the arrow keys to select the desired value (001-512).

• Press the ENTER key to conrm the setting.

• Press the MENU button repeatedly to exit the menu and save changes.

3.6 DMX MODE

The SUNBAR2000FC has more DMX channel congurations which can be accessed from the control panel.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Connect icon, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select DMX Mode and press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select the mode and press ENTER to conrm

your choice.

• Press the MENU button repeatedly to exit the menu and save changes.

The unit is equipped with 5-pole XLR connections.

3.7 DMX ADDRESSING

For operation via light control unit with DMX512 protocol, is sucient connect the controller to SUN-

BAR2000FC. To able to operate the SUNBAR2000FC with a light controller, adjust the DMX start address

for the rst a DMX channel. If e. g. address 33 on the controller is provided for controlling the function of

the rst DMX channel, adjust the start address 33 on the SUNBAR2000FC. The other functions of the light

eect panel are then automatically assigned to the following addresses.

SUNBAR2000FC

12

3.8 ETHERNET

To enable Artnet mode, proceed as follows:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Connect icon, then press the ENTER button to

enter the next menu Ethernet.

Press the UP/DOWN button to scroll through the menu, select Protocol, Universe, Start Channel, IP Address,

Ethernet to DMX and press ENTER to activate the mode.

3.9 ID and RDM

With this function you can call up various submenus via RDM.

This device is RDM ready. RDM stands for “Remote Device Management” and makes remote control of

devices connected to the DMX-bus possible. Manual settings like adjusting the DMX starting address are

no longer needed. This is especially useful when the device is installed in a remote area. RDM is integrated

in DMX without inuencing the connections. The RDM-data is transmitted via the standard XLR-poles 1

and 2 – new DMX-cables are not necessary. RDM ready and conventional DMX devices can be operated

in one DMX line. The RDM protocol sends own packages in the DMX512 data feed and does not inuence

conventional devices. If DMX splitters are used and RDM control is to be used, these splitters must sup-

port RDM. The number and type of RDM parameters depend on the RDM controller (not included) is used.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Connect icon, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, and then select the RDM ID and press the ENTER

button to enter the next menu.

• Press UP/DOWN button to scroll through the menu, then select Password and press ENTER to conrm.

• Use the arrow keys to enter the password 050 and press ENTER to conrm.

• Once you have entered your password, you can set the PID Code, necessary to control the unit with the

RDM protocol. Press the UP/DOWN button to scroll through the menu, select PID Code and press EN-

TER to conrm.

• Use the arrow keys to enter the PID Code, then press the ENTER button to conrm your choice.

• Press the LEFT button repeatedly to exit the menu and save changes.

Fig.19 - Example 4 DMX channels conguration

DMX Address: 44DMX Address: 37DMX Address: 33 DMX Address: 41

. . . . . . . . . . . .

DMX512 Controller

13

SUNBAR2000FC

3.10 TEMPERATURE UNIT

You can change the parameters of the device by following these steps:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Set Up icon, then press the ENTER button to

enter the next menu.

• Press UP/DOWN to scroll through the Temperature menu, select one of the following settings and press

the ENTER button to display it.

• Press the UP/DOWN button to select the unit of measure Celsius/Fahrenheit, then press the ENTER to

conrm the choice

• Press the ENTER button to conrm your choice.

• Press the MENU button repeatedly to exit the menu and save changes.

3.11 SCREEN

You can change the following parameters related to the display, following the same procedure:

• Press the ENTER button to access the main menu.

• Press the UP / DOWN keys to scroll the menu, select the Set Up icon, then press the ENTER button to

enter the next menu.

• Press UP / DOWN to scroll through the menu, then select Screen, and press the ENTER button to enter

the next menu.

• Press UP / DOWN to scroll through the menu, and then select one of the following settings for the dis-

play and press the ENTER key to display it.

- Back Light - Backlight display Auto O. This feature allows you to automatically turn o the backlight

after a specied time that you can set using the arrow buttons. To have the display always on select

On.

- Flip Display - Orientation of the display. This function allows you to rotate the display 180° to get a

better view of the display when the unit is hanging upside down. Select YES to activate or NO to

disable this function.

- Key Lock - Lock keys. With this function, you can lock the buttons on the control panel. If this function

is activated, the keys are automatically locked. To disable or temporarily disable the key lock func-

tion, press the buttons in the following order to regain access to menu commands: UP, DOWN, LEFT,

RIGHT, ENTER. Select YES to activate or NO to disable.

• Press the ENTER button to conrm your choice.

• Press the MENU button repeatedly to exit the menu and save changes.

3.12 FIXTURE

For the SUNBAR2000FC you can access the following special functions:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the icon Set Up, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the Fixture menu, then select one of the following informa-

tion and press the ENTER button to display it.

- White Balance - White Balance Function. Select the White Balance function to set the white bal-

ance by changing the values (125 - 255) of Red, Green, Blue and White colors.

- Dimmer Mode - Dimmer Function. Select Dimmer Mode and choose and simulate dierent dim-

ming curves. Specically, when set to:

Oﬀ - The brightness increase is linear.

Dimmer 1 - Light intensity control is ner at low level and coarse at high levels.

SUNBAR2000FC

14

Dimmer 2 - Light intensity control is ner at high level and coarse at low levels.

Dimmer 3 - Light intensity control is ner at low and high levels, and coarse to medium levels.

- Fans Mode - Select this function to set the fans operation mode. Use the arrow buttons to select Auto

Speed /High Speed. Press the ENTER button to conrm your choice.

• Press the ENTER button to conrm your choice.

Press the MENU button repeatedly to exit the menu and save changes.

3.13 FIXTURE INFORMATION

To view all the information on the device, proceed as follows:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the icon Information, then press the ENTER but-

ton to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, then select one of the following information

and press the ENTER button to display it.

- Fixture Time - Through the Time Information function you can display the operating time of the

projector.

- Temperature - Through the Temperature function can be displayed the temperature inside the x-

ture, near the lamp. The temperature can be displayed in degrees Celsius or Fahrenheit.

- Fans Speed - Through the Fans Speed function you can show on display the fan speed present near

the lamp. Velocity is expressed in RPM (revolutions per minute).

- Software Version - Through Software Version function you can display the currently installed software

version.

• Press the MENU button repeatedly to exit the menu.

3.14 MASTER/SLAVE

This mode will allow you to link up the units together without a controller. Choose a unit to function as the

Master. The unit must be the rst unit in line; other units will work as slave with the same eect.

The Slave unit receives data from the Master unit according to the group which the Slave unit was as-

signed to.

For example, if a slave device is set to Receive Part 1, the Master unit Slave unit will send the automated

Chase Part 1; if set to Receive Part 2, the Chase Part 2 Slave units will receive from the Master.

To set the drive as a slave, proceed as follows:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the StandAlone icon, then press the ENTER button

to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, and select Master/Slave, and press ENTER to

conrm.

• Press the UP/DOWN button to select the dierent modes of operation Master, Slave, and then press the

ENTER button to conrm your choice.

• Press the MENU button repeatedly to exit the menu and save changes.

Select the desired program on the master unit (described in section 3.19).

Use the DMX connectors of the SUNBLAST2000FC and an XLR cable to form a chain of units.

3.15 SEQUENCE

The unit independently runs through its show. Before you send an automatic program you need to set the

drive as Master/Alone:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the StandAlone icon, then press the ENTER button

15

SUNBAR2000FC

to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Sequence and press ENTER to conrm

your choice.

• Press the UP/DOWN button to select the mode of operation: Show 1, Show 2, ....., Show 23

• Press the ENTER button to conrm your choice.

• Press the MENU button repeatedly to exit the menu and save changes.

The unit will go into automatic mode by executing the program automatically.

3.16 STATIC MODE

The unit allows you to create congurations that can be set by the following procedure:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Stand Alone icon, then press the ENTER button

to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Static, and press the ENTER button to

enter the next menu.

• Through the button UP/DOWN select FIXED COLOR or MANUAL COLOR and press the ENTER button to conrm

the desired function.

• Set the color and values (000 - 255), using the UP/DOWN button, then press ENTER button to conrm.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu

SUNBAR2000FC

16

Fig.7

Fig.8

3.17 CONNECTION OF THE DMX LINE

DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120Ω imped-

ance and low capacity.

The following diagram shows the connection mode:

ATTENTION

The screened parts of the cable (sleeve) must never be connected to the system’s earth, as this would

cause faulty xture and controller operation.

Over long runs can be necessary to insert a DMX level matching amplier.

For those connections the use of balanced microphone cable is not recommended because it cannot

transmit control DMX data reliably.

• Connect the controller DMX input to the DMX output of the rst unit.

• Connect the DMX output to the DMX input of the following unit. Connect again the output to the input

of the following unit until all the units are connected in chain.

• When the signal cable has to run longer distance is recommended to insert a DMX termination on the

last unit.

3.18 CONSTRUCTION OF THE DMX TERMINATION

The termination avoids the risk of DMX 512 signals being reected back along the cable when they reach-

es the end of the line: under certain conditions and with certain cable lengths, this could cause them to

cancel the original signals.

The termination is prepared by soldering a 120Ω 1/4 W resistor between pins 2 and 3 of the 5-pin male XLR

connector, as shown in gure.

DMX - OUTPUT

XLR socket

DMX - INPUT

XLR plug

Pin1 : GND - Shield

Pin2 : - Negative

Pin3 : + Positive

Pin4 : N/C

Pin5 : N/C

Example:

5 pin XLR connector

17

SUNBAR2000FC

3.19 DMX CONTROL

BASIC STATIC

CHANNEL FUNCTION DMX

Value

1

RED

0~100% 000 - 255

2

GREEN

0~100% 000 - 255

3

BLUE

0~100% 000 - 255

4

WHITE

0~100% 000 - 255

BASIC STROBE

CHANNEL FUNCTION DMX

Value

1

DIMMER

Blackout

Min to Max

000 - 005

006 - 255

2

FLASH DURATION

15-990ms 000 - 255

3

FLASH RATE

No Flash

Strobe slow to fast

000 - 010

011 - 255

4

FLASH FX

No eect

Static

Ramp up

Ramp down

Ramp up-down

Random

Lighting

Spikes

000 - 002

003 - 005

006 - 042

043 - 085

086 - 128

129 - 171

172 - 214

215 - 255

BASIC PIXEL

CHANNEL FUNCTION DMX

Value

1

PIXEL 1 RED

0~100% 000 - 255

2

PIXEL 1 GREEN

0~100% 000 - 255

3

PIXEL 1 BLUE

0~100% 000 - 255

4

PIXEL 1 WHITE

0~100% 000 - 255

......

61

PIXEL 16 RED

0~100% 000 - 255

62

PIXEL 16 GREEN

0~100% 000 - 255

63

PIXEL 16 BLUE

0~100% 000 - 255

64

PIXEL 16 WHITE

0~100% 000 - 255

SUNBAR2000FC

18

BASIC RGBW STROBE

CHANNEL FUNCTION DMX

Value

1

RED

0~100% 000 - 255

2

GREEN

0~100% 000 - 255

3

BLUE

0~100% 000 - 255

4

WHITE

0~100% 000 - 255

5

DIMMER

Blackout

Min to Max

000 - 005

006 - 255

6

FLASH DURATION

15-990ms 000 - 255

7

FLASH RATE

No Flash

Strobe slow to fast

000 - 010

011 - 255

8

FLASH FX

No eect

Static

Ramp up

Ramp down

Ramp up-down

Random

Lighting

Spikes

000 - 002

003 - 005

006 - 042

043 - 085

086 - 128

129 - 171

172 - 214

215 - 255

PIXELS PIXELS

MODE

CHANNEL

FUNCTION DMX

Value

Ch

1

DIMMER

Blackout

Min to Max

000 - 005

006 - 255

2

FLASH DURATION

15-990ms 000 - 255

3

FLASH RATE

No Flash

Strobe slow to fast

000 - 010

011 - 255

4

FLASH FX

No eect

Static

Ramp up

Ramp down

Ramp up-down

Random

Lighting

Spikes

000 - 002

003 - 005

006 - 042

043 - 085

086 - 128

129 - 171

172 - 214

215 - 255

5

PIXEL 1 RED

0~100% 000 - 255

6

PIXEL 1 GREEN

0~100% 000 - 255

7

PIXEL 1 BLUE

0~100% 000 - 255

8

PIXEL 1WHITE

0~100% 000 - 255

2

9

PIXEL 2 RED

0~100% 000 - 255

10

PIXEL 2 GREEN

0~100% 000 - 255

11

PIXEL 2 BLUE

0~100% 000 - 255

12

PIXEL 2 WHITE

0~100% 000 - 255

4

13

PIXEL 3 RED

0~100% 000 - 255

14

PIXEL 3 GREEN

0~100% 000 - 255

15

PIXEL 3 BLUE

0~100% 000 - 255

16

PIXEL 3 WHITE

0~100% 000 - 255

La pagina sta caricando ...

ProLights SUNBAR2500MAX Manuale utente

Questo manuale è adatto anche per

ProLights SUNBAR2500MAX Manuale utente

in altre lingue

Documenti correlati

Altri documenti