Messoa NDR891 Guida Rapida

ZEIM-4000884G 831(PRO) 891(PRO) A1

Outdoor Dome Network Camera

Quick Start Guide

Guia de inicio rápido

Guida rapida

Guide de démarrage rapide

Краткое руководство

クイックスタートガイド

快速安裝指南

快速安装指南

Quick Start Guide

1

English

Safety Instructions



Make sure the supplied voltage meets the power consumption requirements

of the camera before powering the camera on. Incorrect voltage may cause

damage to the camera.



The camera should be protected from water and moisture, excessive heat,

direct sunlight and cold.



This installation should be made by a qualied service person and should

conform to all local codes.



Unplug the camera during lightening storms or when unused for long

periods of time.

Compliance

This equipment complies with the requirements as listed below:



FCC Part 15 Class B



CE: 2004/108/EC-Electromagnetic Compatibility (EMC) directive of EN55022,

EN61000-3-2, EN61000-3-3 and EN50130-4.

WEEE

Waste Electrical and Electronic Equipment

Correct disposal of this product (applicable in the European Union

and other European countries with separate collection systems). This

product should be disposed of, at the end of its useful life, as per

applicable local lows, regulations and procedures.

2 Quick Start Guide

1. Introduction

1.1 Package Contents



Outdoor Dome Network Camera x1



CD-ROM (User manual and IP Finder utility) x1



Quick Start Guide x1



Guide Pattern Sticker x1



RJ-45 Female / Female Coupler x1



Accessories

• Tapping Type Flat Head Screw (#1) x3

• Plastic Anchor (#2) x3

• Machine Type Flat Head Screw (#3) x3

Quick Start Guide

3

English

1.2 Hardware Overview

Connectors

1

2

3

4

5

6

7

1. Power In (Red+/Black-): Connect to DC 12V/AC 24V (No heater model) or

DC 24V/AC 24V (Heater model) power supply. If using the DC power supply,

make sure the power connector is wired to correct polarities (Red+/Black–). If

you are to use power via the PoE connection, this connector is not used.

2. RJ-45 Ethernet Connector: Network & PoE (Power over Ethernet)

connection. Note that PoE is unable to drive the camera whose heater is

operating.

3. BNC: Composite video output

4. Audio Out (Green): Audio output

5. Audio In (Red): Audio input

6. Alarm Out (Orange): Alarm signal output port

Reserved (Green): Reserved contact

RS-485 (Yellow): Contact for RS-485

7. GND: Ground (electricity) in electrical circuits

Alarm In 1 (Red): Alarm signal input port

Alarm In 2 (Brown): Alarm signal input port

4 Quick Start Guide

2. Installation

2.1 Mounting the Camera

This camera is designed for ceiling & wall mounts depending on your

requirements. Mount the camera to your intended location.

Disassembling

1. Take off the dome cover screws.

2. Rotate the dome cover counterclockwise to unlock and pull free of the

housing.

3. Open (but not remove) the inner liner.

1. Dome Cover Screws

2. Dome Cover

3. Inner Liner

*Model without IR as illustration exmpale

Tip

Caution

Warning Note

For heater model, the dome cover should NOT be removed over 30 minutes

during installation. Otherwise, the desiccant may absorb too much moisture and

thus cause vapor when the heater is on.

Quick Start Guide

5

English

Drilling the Mounting Surface

1. Post the “Guide Pattern” sticker on the mounting surface.

2. Aiming the circles (the gure below marked with “+“ ) on the sticker, drill

three screw holes and one cable entry hole in the ceiling/wall.

+

Mounting the Camera

Use the machine screws to secure the camera base to the surface (this gure take

the tapping type screws as the example to illustrate the mounting).

Guide Pattern Sticker

Tapping Type Screw

Plastic Anchor

Camera Base

*Model without IR as illustration exmpale

TipCautionWarning

Note

1. While you are securing the camera with the accompanying screws, please be

advised to hold the camera by its base. Do not hold the lens or lens base with

force that may deform the lens.

2. Use the machine type screws if you are attaching the camera to a pendent

mounting. Use the tapping type screws for all other surfaces.

3. For cement surfaces, insert the “Plastic Anchors” into the holes. For softer

surfaces, do not use the “Plastic Anchors”.

6 Quick Start Guide

Adjusting Camera Angle

Check the monitored view by wiring the RCA jack to a monitor. With an external

monitor connected, you can adjust the camera angle, zoom and focus for

appropriate or better view.

RCA Jack for Composite Video

Output

Model without IR

RCA Jack for

Composite Video Output

Model with IR

Quick Start Guide

7

English

Pan Adjustment: Rotate the lens base to adjust the horizontal angle.

Tilt Adjustment: Tilt the lens base to adjust the vertical angle.

Tile Angle (max. 90 degrees)

No IR model

Pan Angle (max. 355 degrees)

Model without IR

Tilt Angle (max. 70 degrees)

Pan Angle (max. 355 degrees)

Model with IR

8 Quick Start Guide

Horizontal rotation: Rotate the dome base to adjust the horizontal position. Do

not turn the base more than 355° as this may cause the internal cables to twist

and disconnect or break.

Horizontal Rotation

(max. 355 degrees)

Model without IR

Horizontal Rotation

(max. 355 degrees)

Model with IR

Quick Start Guide

9

English

TipCautionWarning

Note

When the tilt angle is less than 75/70 degrees, there is no distortion.

24

°

Wide Angle (9mm)

68

°

Tele Angle (3mm)

75

°

Tilt Angle

Distortion Area

Model without IR

24

°

Wide Angle (9mm)

68

°

Tele Angle (3mm)

70

°

Tilt Angle

Distortion Area

Model with IR

10 Quick Start Guide

Lens Adjustment: Loosen the screws to adjust the zoom control for desired

image view and adjust the focus for optimum picture sharpness. Re-tighten the

screws after nishing zoom/focus adjustments.

Tele (T) & Wide (W)

Near (N) & Far (

∞

)

*Model without IR as illustration exmpale

Assembling the Camera

1. Close the inner liner.

2. If you are to use a microSD/SDHC card, remember to insert the card into the

slot before assembling the dome cover.

3. Assemble the dome cover.

4. Secure the dome cover with the accompanying screw.

Quick Start Guide

11

English

2.2. Initial Conguration via a PC

Before connecting the camera to your network infrastructure, it’s suggested that

you connect the camera to a computer rst to perform initial congurations.

1. Configure the computer’s IP address that must be on the same network

segment with the camera’s default IP address (192.168.1.30 by default), such

as:

• IP Address: 192.168.1.100

• Subnet Mask: 255.255.255.0

2. Connect the RJ-45 cable of the camera to the computer.

The LAN port of the camera supports auto MDI/MDIX so there is no need to

use a cross-over cable.

3. To make sure the connection between the camera and the computer is

successful established, you can attempt to ping the camera from your

computer.

• First click the Start menu and select Programs. Then select Accessories.

• Choose Command Prompt. Click OK.

• Type ping x.x.x.x, where x.x.x.x is the IP address of the camera (default

is 192.168.1.30). If the message of “Reply from…” appears, it means the

connection is done.

4. On the PC, launch a web browser and enter the IP address of the camera in

the URL eld:

http://192.168.1.30/

5. When prompted for login, respectively enter the default user name: admin

and password: 1234 to log in. Note that the user name and password are

case-sensitive.

6. Configure the settings to meet your requirements. For more information,

refer to the User Manual on the provided CD-ROM.

12 Quick Start Guide

2.3 Connecting to Your Network

Connecting to a LAN

If you have multiple cameras installed on your network, you can use the provided

IP Finder utility to manage the cameras. For more information, refer to the User

Manual on the provided CD-ROM.

Router/Switch/Hub

Connecting to the Internet

Router

x D S L / C a b l e

Modem

To enable remote access to the cameras, you must congure your router/rewall

to open port numbers. For more information, refer to the User Manual on the

provided CD-ROM.

Cámara de Red Domo para Exteriores

Quick Start Guide

Guia de inicio rápido

Guida rapida

Guide de démarrage rapide

Краткое руководство

クイックスタートガイド

快速安裝指南

快速安装指南

ZEIM-4000884G 831(PRO) 891(PRO) A1

Guía de inicio rápido

1

Español

Instrucciones de seguridad



Asegúrese de que el voltaje suministrado reúne los requisitos de consumo

energético de la cámara antes de encenderla. Un voltaje incorrecto podría

dañar la cámara.



La cámara debe estar protegida del agua y la humedad, calor excesivo, frío y

luz directa del sol.



La instalación debe ser realizada por personal cualicado de mantenimiento

siguiendo todas las normativas locales.



Desconecta la cámara durante tormentas eléctricas o cuando no vaya a ser

utilizada durante largos periodos de tiempo.

Conformidad

Este equipo cumple con los siguientes requisitos mostrados a continuación:



FCC Apartado 15 Clase B



CE: Directiva de Compatibilidad Electromagnética (EMC) 2004/108/EC de

EN55022, EN61000-3-2, EN61000-3-3 y EN50130-4.

WEEE

Residuos de aparatos eléctricos y electrónicos

Deshecho correcto de este producto (aplicable en la Unión Europea

y en otros países europeos con sistemas diferentes de recogida). Este

producto debería ser retirado al nal de su vida útil según las leyes,

normativas y procedimientos locales.

2 Guía de inicio rápido

1. Introducción

1.1 Contenidos del paquete



Cámara de Red Domo para Exteriores x1



CD-ROM (Manual de usuario y Utilidad para encontrar la IP) x1



Guía de inicio rápido x1



Pegatina del patrón de guía x1



Acoplador hembra/RJ-45 hembra x1



Accesorios

• Tornillo de cabeza plana tipo enroscante (#1) x3

• Taco de plástico (#2) x3

• Tornillo de cabeza plana tipo máquina (#3) x3

Guía de inicio rápido

3

Español

1.2 Presentación del Hardware

Conectores

1

2

3

4

5

6

7

1. Entrada de la fuente de alimentación (Rojo +/Negro -): Conecte a la

fuente de alimentación CC 12V/AC 24V (Modelo sin calentador) o CC 24V/

AC 24V (Modelo con calentador). Si va a utilizar la fuente de alimentación

CC, asegúrese de que el conector esté conectado en las polaridades

correctas (Rojo+/Negro-). Si va a utilizar la conexión PoE para suministrar la

electricidad, no se usará este conector.

2. RJ-45 (Ethernet/PoE): Conexión PoE (Power over Ethernet) y de red. Tenga

en cuenta que PoE no puede manejar la cámara que esté operando su

radiador.

3. BNC: Salida de vídeo compuesto

4. Salida de audio (Verde): Salida de audio

5. Entrada de audio (Rojo): Entrada de audio

6. Salida de alarma (Naranja): Puerto de salida de señal de alarma

Reservado (Verde): Contacto reservado

RS-485 (Amarillo): Contacto para RS-485

7. TDT: Toma de tierra (electricidad) de los circuitos eléctricos

Entrada de Alarma 1 (Rojo): Puerto de entrada de señal de alarma

Entrada de Alarma 2 (Marrón): Puerto de entrada de señal de alarma

4 Guía de inicio rápido

2. Instalación

2.1 Instalación de la cámara

Esta cámara ha sido diseñada para ser instalada en el techo o en la pared

dependiendo de sus necesidades. Instale la cámara en el lugar deseado.

Desmontaje

1. Extraiga el tornillo de la cubierta domo.

2. Gire la cubierta domo en el sentido contrario a las agujas del reloj para

desbloquearla y extraerla de la carcasa.

3. Abra (pero no extraiga) el alineador interior.

1. Tornillos de la cubierta domo

2. Cubierta domo

3. Alineador interior

*Modelo sin IR como ejemplo

Tip

Precaución

Warning Nota

Para el modelo con radiador, la cubierta domo NO debe ser extraida tras 30

minutos durante la instalación. De lo contrario, el desecante podría absorver

demasiada humedad, causando vapor cuando el radiador estuviera encendido.

La pagina sta caricando ...

Messoa NDR891 Guida Rapida

Questo manuale è adatto anche per

Messoa NDR891 Guida Rapida

in altre lingue

Documenti correlati

Altri documenti