HP 530 Manuale utente

Installation and

Getting Started Guide

www.procurve.com

ProCurve Wireless Access Point 530

Power over Ethernet Devices

In

ProCurve

Wireless Access Point 530

Installation and Getting Started Guide

Hewlett-Packard Company

8000 Foothills Boulevard, m/s 5552

Roseville, California 95747-5552

http://www.procurve.com

L.P. The information contained herein is subject to change

without notice.

This document contains proprietary information, which is

protected by copyright. No part of this document may be

photocopied, reproduced, or translated into another language

without the prior written consent of Hewlett-Packard.

Publication Number

5992-5444

October 2008

Applicable Products

Disclaimer

HEWLETT-PACKARD COMPANY MAKES NO WARRANTY

OF ANY KIND WITH REGARD TO THIS MATERIAL,

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not be

liable for errors contained herein or for incidental or consequential

damages in connection with the furnishing, performance, or use

of this material.

The only warranties for HP products and services are set forth in

the express warranty statements accompanying such products and

services. Nothing herein should be construed as constituting an

additional warranty. HP shall not be liable for technical or editorial

errors or omissions contained herein.

Hewlett-Packard assumes no responsibility for the use or

reliability of its software on equipment that is not furnished by

Hewlett-Packard.

Warranty

See the Customer Support/Warranty booklet included with the

product.

A copy of the specific warranty terms applicable to your Hewlett-

Packard products and replacement parts can be obtained from your

HP Sales and Service Office or authorized dealer.

Safety

Before installing and operating these products, please read the

“Installation Precautions” in chapter 2, “Installing the Access

Point 530”, and the safety statements in appendix C, “Safety and

EMC Regulatory Statements”.

Open Source Software Acknowledgement

Statement

This software incorporates open source components that

are governed by the GNU General Public License (GPL),

version 2. In accordance with this license, ProCurve

Networking will make available a complete, machine-

readable copy of the source code components covered by

the GNU GPL upon receipt of a written request. Send a

request to:

Hewlett-Packard Company, L.P.

AP 530 Program

GNU GPL Source Code

Attn: ProCurve Networking Support

MS: 5551

Roseville, CA 95747 USA

Open source licenses pertaining to the open source software

included with the product can be found in Appendix C in this

guide.

ProCurve Wireless Access Point 530 NA (J8986A)

ProCurve Wireless Access Point 530 WW (J8987A)

i

Contents

1 Introducing the ProCurve Wireless Access Point 530

Top of the Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Back of the Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

Back Panel Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

Console Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

Network Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

Power Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

Reset Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

Clear Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

Auxiliary Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

Access Point Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9

Getting Documentation from the Web . . . . . . . . . . . . . . . . . . . . . . . . . 1-10

2 Installing the Access Point 530

Included Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Installation Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Installation Precautions: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

1. Prepare the Installation Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

2. Verify the Access Point Completes Initialization . . . . . . . . . . . . . . . 2-5

LED Behavior: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

3. Mount the Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

Standard Electrical Box Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

Suspended Ceiling Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

Horizontal Surface Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12

4. Connect the Access Point to a Power Source . . . . . . . . . . . . . . . . . 2-12

5. Connect the Network Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13

Using the RJ-45 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13

ii

6. (Optional) Connect External Antennas to the Access Point . . . . . 2-13

7. (Optional) Connect a Console to the Access Point 530 . . . . . . . . . 2-14

Terminal Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14

Direct Console Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15

Sample Network Topologies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17

Infrastructure Wireless LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18

Infrastructure Wireless LAN with Roaming . . . . . . . . . . . . . . . . . . . . . 2-19

Wireless Distribution System (WDS) Bridge . . . . . . . . . . . . . . . . . . . . 2-21

Wireless Distribution System (WDS) Repeater . . . . . . . . . . . . . . . . . . 2-23

3 Getting Started With Access Point Configuration

Recommended Minimal Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Using the Command Line Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

To Set the Manager User Name and Password . . . . . . . . . . . . . . . 3-2

To Set the Access Point’s IP Address . . . . . . . . . . . . . . . . . . . . . . . 3-3

To Set the Access Point’s Country Code . . . . . . . . . . . . . . . . . . . . . 3-4

To Configure Radio Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Where to Go From Here . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

Using the IP Address for Remote Access Point Management . . . . 3-10

Starting a Telnet Session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10

Starting an SSH Session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11

Starting a Web Browser Session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11

4 Using an External Antenna with the Access Point 530

External Antenna Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Installation Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

1. Plan the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

2. Mount the Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

3. Connect Pigtail Cables to the Access Point . . . . . . . . . . . . . . . . . . . . 4-4

4. Configure the Antenna Mode and Type . . . . . . . . . . . . . . . . . . . . . . . 4-6

Setting the Antenna Mode and Type Using the CLI . . . . . . . . . . . . 4-6

Setting the Antenna Mode and Type Using the Web Interface . . . 4-6

iii

5 Troubleshooting

Basic Troubleshooting Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Diagnosing with the LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

Proactive Networking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

Hardware Diagnostic Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7

Testing the Access Point by Resetting It . . . . . . . . . . . . . . . . . . . . . . . . 5-7

Checking the Access Point’s LEDs . . . . . . . . . . . . . . . . . . . . . . . . . 5-7

Checking Event Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7

Testing Twisted-Pair Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8

Testing Access Point-to-Device Network Communications . . . . . . . . 5-8

Testing End-to-End Network Communications . . . . . . . . . . . . . . . . . . 5-8

Restoring Custom and Factory Default Configurations . . . . . . . . . . 5-9

Downloading New Access Point Software . . . . . . . . . . . . . . . . . . . . . . 5-11

HP Customer Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11

Before Calling Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11

A Specifications

Physical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Japanese Power Cord Statement . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

EMC Compliance (Class B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

Radio Signal Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3

Immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3

Wireless . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3

Receiver Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-5

Internal Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-5

B Access Point Port and Network Cables

Access Point Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

Twisted-Pair Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

iv

Twisted-Pair Cable/Connector Pin-Outs . . . . . . . . . . . . . . . . . . . . . . . B-2

Straight-Through Twisted-Pair Cable for

10 Mbps or 100 Mbps Network Connections . . . . . . . . . . . . . . . . . . . . B-3

Cable Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3

Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3

Crossover Twisted-Pair Cable for

10 Mbps or 100 Mbps Network Connection . . . . . . . . . . . . . . . . . . . . . B-4

Cable Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4

Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4

C Safety and EMC Regulatory Statements

Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1

Informations concernant la sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2

Hinweise zur Sicherheit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3

Considerazioni sulla sicurezza . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-5

Consideraciones sobre seguridad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-6

Safety Information (Japan) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-8

Safety Information (Korea) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-9

Safety Information (China) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-10

EMC Regulatory Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-11

Notice for U.S.A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-11

Regulatory Model Identification Number . . . . . . . . . . . . . . . . . . C-12

Notice for Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-12

Notice for European Community . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-13

Supported Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-16

EU Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-17

Notice for Japan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-18

Notice for Taiwan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-18

Notice for Korea . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-19

Licenses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-19

D Recycle Statements

Waste Electrical and Electronic Equipment (WEEE) Statements D-1

1-1

Introducing the ProCurve

Wireless Access Point 530

1

Introducing the ProCurve

Wireless Access Point 530

The ProCurve Wireless Access Point 530 is an enterprise-class, dual-radio

802.11b/g and 802.11a/b/g access point that offers maximum flexibility in

deployment and optimum throughput for high-density usage areas.

The access point provides comprehensive security and management features

and is capable of supporting all types of wireless stations in the same coverage

area. The unit includes internal diversity antennas for both radios and also

connectors for attaching a variety of external antenna options. Mounting

options for the unit include horizontal surface, wall, suspended ceiling T-rail,

and plenum space.

Throughout this manual, this access point will be abbreviated as the

Access Point 530.

The Access Point 530 has one 10/100Base-TX RJ-45 port. This port also

supports Power over Ethernet (PoE) based on the IEEE 802.3af standard. The

access point supports wireless connectivity at speeds up to 54 Mbps based on

the IEEE 802.11g and IEEE 802.11a standards.

ProCurve Wireless Access Point 530 NA (J8986A)

ProCurve Wireless Access Point 530 WW (J8987A)

1-2

Introducing the ProCurve Wireless Access Point 530

Introducing the ProCurve

Wireless Access Point 530

This access point is designed to be used primarily for connecting wireless

stations to an enterprise network. This access point allows wireless stations

to connect directly to each other, or to connect to other computers or network

resources located on the wired network.

This chapter describes your Access Point 530 including:

■ Top and back of the access point

■ Access point features

1-3

Introducing the ProCurve Wireless Access Point 530

Top of the Access Point

Introducing the ProCurve

Wireless Access Point 530

Top of the Access Point

ProCurve Wireless Access Point 530

Indicator Panel

Power LED

Ethernet LEDWireless LED

Back Panel Covers

1-4

Introducing the ProCurve Wireless Access Point 530

Top of the Access Point

Introducing the ProCurve

Wireless Access Point 530

LEDs

Table 1-1. Access Point LEDs

Access Point

LEDs

State Meaning

Power

(green)

On The access point is receiving power.

Off The access point is NOT receiving power.

LAN

(green)

Off The RJ-45 port has no network cable connected, or is not receiving a link signal.

Blinking or

On

The RJ-45 port has a link indication from a 10 Mbps or 100 Mbps device and is

transmitting or receiving traffic. The LED blinking rate is proportional to the traffic

rate. If there is no traffic, the blinking rate will be once every five seconds. As the

traffic rate increases, the blinking rate also increases until the LED is solid on, which

indicates there no available bandwidth on the port.

Radio 1 (11b/g)

Radio 2 (11a/b/g)

(green)

Off The wireless interface is disabled, either through the access point console or the

Web browser interface.

Blinking or

On

The wireless interface is enabled and transmitting or receiving traffic. The LED

blinking rate is proportional to the traffic rate. If there is no traffic, the blinking rate

will be once every five seconds. As the traffic rate increases, the blinking rate also

increases until the LED is solid on, which indicates there no available bandwidth

on the interface.

1-5

Introducing the ProCurve Wireless Access Point 530

Back of the Access Point

Introducing the ProCurve

Wireless Access Point 530

Back of the Access Point

Back Panel Covers

The access point’s ports and connectors on the back of the unit can be

protected by two removable plastic covers. One covers the Console port, Clear

and Reset buttons, RJ-45 port, and DC power connector, while allowing

twisted-pair and power cables to pass through. The other cover protects the

external antenna connectors when they are not in use.

Antennas

The access point includes internal diversity antennas for wireless communi-

cations. A diversity antenna system uses two identical antennas to receive and

transmit signals, helping to avoid multipath fading effects. When receiving,

the access point checks both antennas and selects the one with the strongest

signal. When transmitting, it will continue to use the antenna previously

selected for receiving. The access point never transmits from both antennas

at the same time.

Reset and Clear

buttons

External Antenna

connectors

ProCurve Wireless Access Point 530

Network port

10/100Base-TX RJ-45

port and PoE input

DC power connector

Console port

Lock

(on side panel)

Auxiliary port and LED

1-6

Introducing the ProCurve Wireless Access Point 530

Back of the Access Point

Introducing the ProCurve

Wireless Access Point 530

The access point also supports connectors for various external antenna

options that offer extended radio range and specific radio coverage patterns.

For further information, see chapter 4, “Using an External Antenna with the

Access Point 530”.

Lock

The access point includes a Kensington security slot on the side panel, marked

with the lock symbol ( ). You can prevent unauthorized removal of the

access point by wrapping the Kensington security cable (not provided) around

an unmovable object, inserting the lock into the slot, and turning the key.

Console Port

This port connects a console to the access point using a serial cable. This

connection is described under “Connect a Console to the Access Point” in

chapter 2, “Installing the Access Point 530”. The console can be a PC or

workstation running a VT-100 terminal emulator, or a VT-100 terminal.

Network Port

The access point includes one 10/100Base-TX port. This port uses the “HP Auto

MDIX” feature, which means that you can use either straight-through or

crossover twisted-pair cables to connect the access point to a switch or

workstation.

Refer to the following section for information on supplying power to the

access point through its RJ-45 port from a network device, such as a switch,

that provides Power over Ethernet (PoE).

Power Connector

The Access Point 530 does not have a power switch; it is powered on when

connected to the AC power adapter, and the power adapter is connected to

an active AC power source. The access point's power adapter automatically

adjusts to any voltage between 100--240 volts and either 50 or 60 Hz. There are

no voltage range settings required.

Caution Use only the AC power adapter supplied with the access point. Use of other

adapters, including adapters that came with other ProCurve Networking

products, may result in damage to the equipment.

1-7

Introducing the ProCurve Wireless Access Point 530

Back of the Access Point

Introducing the ProCurve

Wireless Access Point 530

The access point may also receive Power over Ethernet (PoE) from a switch

or other network device that supplies power over the network cable based on

the IEEE 802.3af standard.

Note that if the access point is connected to a PoE source device and also

connected to a local power source through the AC power adapter, PoE will

be disabled.

Reset Button

This button is used to reset the hardware or restore the factory defaults:

■ To Reset the Access Point While it is Powered On – When the Reset

button is pressed for about one second all the LEDs turn off, then after

another second the LEDs start to blink rapidly. Releasing the button when

the LEDs are blinking rapidly clears any temporary error conditions that

may have occurred and restarts the access point initialization.

■ To Restore Custom Default Configuration – When pressed with the

Clear button in a specific pattern, any configuration changes you may have

made through the access point console or the Web browser interface are

removed, and the customer-specified default configuration is restored to

the access point. For the specific method to restore the customer default

configuration, see “Restoring Custom and Factory Default Configura-

tions” in chapter 5, “Troubleshooting” of this guide.

■ To Restore Factory Default Configuration – When pressed with the

Clear button in a specific pattern, any configuration changes you may have

made through the access point console or the Web browser interface are

removed, and the factory default configuration is restored to the access

point. For the specific method to restore the factory default configuration,

see “Restoring Custom and Factory Default Configurations” in chapter 5,

“Troubleshooting” of this guide.

Note The system, password, custom default, and factory default reset functions can

be disabled by the access point’s software. For more information, see the

Management and Configuration Guide, which is available for download on

the ProCurve Networking Web site at http://www.procurve.com/manuals.

1-8

Introducing the ProCurve Wireless Access Point 530

Back of the Access Point

Introducing the ProCurve

Wireless Access Point 530

Clear Button

This button is used for these purposes:

■ Deleting the Password - When pressed by itself for at least one second,

the button resets the Manager password to the factory default setting for

all of the access point’s interfaces. Use this feature if you have misplaced

the password and need management access.

■ To Restore Custom Default Configuration – When pressed with the

Reset button in a specific pattern, any configuration changes you may

have made through the access point console or the Web browser interface

are removed, and the customer-specified default configuration is restored

to the access point. For the specific method to restore the customer

default configuration, see “Restoring Custom and Factory Default Config-

urations” in chapter 5, “Troubleshooting” of this guide.

■ Restoring Factory Default Configuration - When pressed with the

Reset button in a specific pattern, any configuration changes you may

have made through the console, the Web browser interface, and SNMP

management are removed, and the factory default configuration is

restored to the access point. For the specific method to restore the factory

default configuration, see “Restoring Custom and Factory Default Config-

urations” in chapter 5, “Troubleshooting” of this guide.

Auxiliary Port

The Auxiliary port is reserved for future use.

1-9

Introducing the ProCurve Wireless Access Point 530

Access Point Features

Introducing the ProCurve

Wireless Access Point 530

Access Point Features

The wireless features of the Access Point 530 include:

■ dual-radio design with IEEE 802.11b/g and IEEE 802.11a/b/g radios

■ supports up to 16 Service Set IDentifier (SSID) interfaces

■ independent security and VLAN settings per SSID interface

■ supports up to 256 wireless stations per radio interface

■ IEEE 802.11a/b/g compliant – interoperable with multiple vendors

■ precise control over signal transmission power and data rate

■ advanced security through 64/128/152-bit WEP encryption, Wi-Fi

Protected Access (WPA and WPA2), IEEE 802.1X, remote authentication

via a RADIUS server, and MAC address filtering features to protect your

sensitive data and authenticate only authorized users to your network

■ remote logging of system messages

■ time synchronization via SNTP server for message logs

■ wireless bridging between access points

■ neighbor access point detection

■ Quality of Service (QoS) support through Wi-Fi Multimedia (WMM) and

Spectralink Voice Priority (SVP)

■ secured authentication of wireless clients through the client’s Web

browser

■ Adaptive Transmit Power Control, to minimize same-channel interference

and maximize channel coverage

■ support for SNMP audible client/PROBE requests (requires PMM 2.0)

■ support for automatic configuration of a group of Access Point 530s

■ de-authentication and lockout of individual clients by MAC address

■ secure authentication of the Access Point 530 on network ports protected

by 802.1X port-based authentication

■ group configuration of up to 12 access points

■ support for wireless sFlow

■ auto channel selection – simplifies deployment by testing all available

channels and selecting the best channel based on signal-to-noise ratio

■ international country configuration – select the appropriate country and

the access point automatically configures radio operation to match regu-

latory requirements (model J8987A only)

The other basic features of the Access Point 530 include:

1-10

Introducing the ProCurve Wireless Access Point 530

Access Point Features

Introducing the ProCurve

Wireless Access Point 530

■ one 10/100Base-TX RJ-45 port

■ supports Power over Ethernet based on the IEEE 802.3af standard

■ full-duplex operation for the 10/100 RJ-45 port

■ easy management of the access point through several available interfaces:

• console interface—a full featured, easy to use, VT-100 terminal

interface that is especially good for out-of-band access point manage-

ment and for Telnet or Secure Shell access to the access point

• Web browser interface—an easy to use built-in graphical interface

that can be accessed from common Web browsers (includes support

for secure HTTP connections)

• SNMP—a network management application such as HP ProCurve

Manager can manage the access point via the Simple Network

Management Protocol (SNMP) from a network management station

(supports SNMP versions 1, 2c, and 3)

■ support for IEEE 802.1Q-compliant VLANs (as specified for each station

in the RADIUS server) so that wireless stations can join the appropriate

logical grouping for the network user’s needs

■ support for Identity Driven Management and RADIUS assigned VLANs

■ RADIUS Accounting for logging user activity on the network

■ support for many advanced features to enhance network performance—

for a description, see the Management and Configuration Guide, which

is available for download on the ProCurve Networking Web site at

http://www.procurve.com/manuals.

■ download of new access point software for software updates

■ upload and download of access point configuration files

Getting Documentation from the Web

PDF versions of this document, the AP-530 Management and Configuration

Guide, and release notes are available online.

1. Go to the ProCurve Networking Web site at

http://www.procurve.com/manuals

2. Click on the name of the product for which you want documentation.

3. On the resulting web page, double-click on a document you want.

4. Save the document to your hard disk.

2-1

Installing the

Access Point 530

2

Installing the Access Point 530

The Access Point 530 is easy to install. It comes with an accessory kit that

includes a bracket for mounting the access point on a wall or to a suspended

ceiling T-rail. The bracket is designed to allow mounting the access point in a

variety of locations and orientations.

This chapter shows you how to install your Access Point 530.

Included Parts

The Access Point 530 has the following components shipped with it:

■ ProCurve Wireless Access Point 530 Installation and Getting Started

Guide (5992-5444), this manual

■ Customer Support/Warranty booklet

■ Accessory kit (5070-1657)

• four 5/8-inch number 12 wood screws to attach the access point to a

wall

• four plastic wall plugs for mounting on a brick or concrete wall

• four rubber feet

■ Mounting bracket (5188-4682)

■ AC power adapter (5188-3767 or 5189-2946)

■ AC power cord, one of the following:

United States/Canada/Mexico

Continental Europe

United Kingdom/Hong Kong/Singapore

Australia/New Zealand

Japan

China

Denmark

Switzerland

8120-0740

8121-0731

8121-0739

8121-0730

8121-0736

8121-0742

8121-0733

8121-0738

2-2

Installing the Access Point 530

Installation Procedures

Installing the

Access Point 530

Installation Procedures

Summary

Follow these easy steps to install your access point. The rest of this chapter

provides details on these steps.

1. Prepare the installation site (page 2-4). Make sure that the physical

environment into which you will be installing the access point is properly

prepared, including having the correct network cabling ready to connect

to the access point and having an appropriate location for the access

point. Please see page 2-2 for some installation precautions.

2. Verify that the access point completes its system initialization

(page 2-5). This is a simple process of plugging the access point into a

power source, or connecting it to a switch that provides Power over

Ethernet, and observing that the LEDs on the access point’s top panel

indicate correct access point operation.

3. Mount the access point (page 2-7). The Access Point 530 can be

mounted on a wall, on a suspended ceiling T-rail, or on a horizontal

surface.

4. Connect power to the access point (page 2-12). Once the access

point is mounted, plug it into a nearby main power source, or connect it

to a switch that provides Power over Ethernet.

5. Connect to the network (page 2-13). Using the appropriate network

cable, connect the access point to a network connection point, such as a

switch. The network connection can also be used to provide power to the

access point through its PoE feature.

6. Connect a console to the access point (optional—page 2-14). You

may wish to modify the access point’s configuration, for example, to

configure an IP address so it can be managed using a Web browser or

through a Telnet session. Configuration changes can be made easily by

using a console cable to connect a PC to the access point’s console port.

At this point, your access point is fully installed. See the rest of this chapter if

you need more detailed information on any of these installation steps.

La pagina sta caricando ...

HP 530 Manuale utente

Questo manuale è adatto anche per

HP 530 Manuale utente

in altre lingue

Altri documenti