Intermec MaxiScan 2300 Manuale utente

User's manual

Intermec MaxiScan 2300 VS

Pollux manual deel_1 03-11-2000 10:27 Pagina a

Regulatory Statements

CE Intermec hereby declares that the MaxiScan 2300 VS has been tested and found compliant with

the below listed standards as required by the EMC Directive 89/336EEC as amended by 92/31/EEC

and by the Low Voltage Directive 73/23/EEC as amended by 93/68/EEC:

EN 55022 (1992)

EN 50082 (1998)

EN 60950 (1993)

USA: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. It generates, uses and can radiate radio frequency energy. If not

installed and used in accordance with the instructions, it may cause interference to radio

communications. If this equipment causes interference, the user will be required to correct the

interference at the user’s own expense.

This equipment complies with the UL 1950 standard.

Canada: This Class B digital apparatus meets all requirements of the Canadian Interference Causing

Equipment Regulations.

Cet appareil numerique de la classe B respect toutes les exigences du Reglement sur le materiel

brouilleur du Canada.

This equipment complies with the UL 1950 standard.

Cet equipment ext conforme a la norme UL 1950.

Mexico: Este equipo cumple con la certification NOM.

Australia –New Zealand: This equipment has been tested and found to conform to the Australian EMC

framework concerning Class B digital devices, prescribed by the Australian and New-Zealand standard

AS/NZS 3548.

The information contained in this document is for informational purposes only and is subject to change

without notice. No part of this document may be copied or reproduced in any manner without the prior

written permission of Intermec Technologies Corporation.

The word Intermec, the Intermec logo, Scanplus and EasySet are either trademarks or registered

trademarks of Intermec.

Throughout this document, trademarked names may be used. Rather than put a trademark (tm or R)

symbol in every occurrence of a trademarked name, we state that we are using the names only in an

editorial fashion, an do the benefit of the trademark owner, with no intention of infringement.

P/N 3-450049-01 October 2000

Pollux manual deel_1 03-11-2000 10:27 Pagina b

Table of contents

Preface i

Chapter 1 The MaxiScan 2300 VS 1

1.1 Unpacking the MaxiScan 2300 VS 2

1.2 Scanning bar codes with the MaxiScan 2300 VS 4

1.3 Scanner labelling 6

1.4 Maintaining the scanner 9

1.5 Controlling the scanner from the POS system 9

Chapter 2 Installing the MaxiScan 2300 VS 11

2.1 Installing the scanner on a counter surface 13

2.2 Installing the scanner using the flexible stand 17

Chapter 3 Mounting options MaxiScan 2300 VS 21

3.1 Flyby mode scanning: right to left 23

3.2 Flyby mode scanning: left to right 25

3.3 Presentation mode scanning 27

Appendices A. Connector types and pin definitions 30

B. Technical specifications 32

C. Troubleshooting 33

Pollux manual deel_1 03-11-2000 10:27 Pagina c

Preface

The MaxiScan 2300 VS is an innovative, high performance food retail scanner,

combining unequalled performances with enormous installation flexibility. It has a

unique four-directional sealed optical assembly, allowing it to be turned inside

the fixed scanner housing. This new benchmark for vertical supermarket and

hypermarket scanning ensures an ergonomic and user-friendly implementation

wherever it is installed. The MaxiScan is also one of the flattest scanners

available today, making installation at the check-out even easier.

Two versions of the MaxiScan are available, one unit has RS232C and OCIA

interfaces and the other has IBM RS485 and Keyboard Wedge interfaces. An

auxiliary port for connecting another scanner is standard.

This manual contains three chapters and three appendices. The first chapter

describes the MaxiScan 2300 VS and its general features. The MaxiScan can be

installed on a counter surface or on a flexible stand. Instructions for the

installation are described in the second chapter. Precisely follow the instructions

for the installation of the scanner. Default settings can be changed with the bar

code labels from the Configuration Guide that came with the scanner. The third

chapter describes all possible mounting options. Appendix A shows all

connectors of the scanner. Technical specifications of the MaxiScan 2300 VS

can be found in Appendix B. Refer to Appendix C for troubleshooting if the

scanner is not working properly.

Pollux manual deel_1 03-11-2000 10:27 Pagina d

Chapter 1

The MaxiScan 2300 VS

Pollux manual deel_1 03-11-2000 10:27 Pagina e

1.1 UNPACKING THE MAXISCAN 2300 VS

Remove the scanner and its accessories from the box and packing material.

Refer to the packing list to make sure you have received all the items ordered.

Visually inspect the scanner and accessories for any evidence of physical

damage. Refer to the figure on page 6 to locate the interface label and make

sure that the scanner interface corresponds with the host system interface.

Immediately contact your supplier if anything appears to be damaged, or if the

supported interface does not correspond with the host system interface.

The various parts of the MaxiScan 2300 VS are:

2 The MaxiScan 2300 VS

LED

Sleep mode switch

THE Maxiscan 2300 VS

Good read speaker

Pollux manual deel_1 03-11-2000 10:27 Pagina 2

The various parts of the MaxiScan 2300 VS are:

Sleep mode switch - When a sleep mode time-out is programmed, the -

scanner can be re-activated by pressing this switch.

The sleep-mode feature is programmable with the

menu labels from the Configuration Guide.

NOTE: The default value for the sleep mode time-out

is set to 30 minutes. When the scanner is in

sleep mode, the LED is intermittently flashing

red.

LED - A red LED indicates that the scanner is ready to read

a bar code. A green LED indicates a good read.

Good read speaker - The speaker is heard whenever data has been read

correctly. The frequency and volume can be adjusted

with the menu labels from the Configuration Guide.

The MaxiScan 2300 VS 3

Pollux manual deel_1 03-11-2000 10:27 Pagina 3

1.2 SCANNING BAR CODES WITH THE MAXISCAN 2300 VS

The MaxiScan 2300 VS is an omni-directional scanner featuring a 5 directional

scan field with a 20 lines scan pattern. The scanner's scan volume is illustrated

in the figure below. The optimal reading zone lies between 1 and 9 cm from the

scanner window, but bar codes can be read up to 30 cm (11.8 in.) from the

scanner window. The scanner can be used in either fly by or presentation mode.

Scanning a bar code label in fly by mode is very simple: pass the product’s bar

code label along the scanner as illustrated in the figure below.

4 The MaxiScan 2300 VS

front view

Fly by mode:

scan pattern

volume

1 cm

optimal

reading zone

top view

9 cm

30 cm

product flow

scanner in

fly by mode

1. Pass the label along the scanner.

Bar code is read (green led).

☞

1

special offer

chewing-gum

Pollux manual deel_1 03-11-2000 10:27 Pagina 4

Scanning a bar code label in presentation mode is also very simple: present the

product’s bar code label to the scanner as illustrated in the figure below.

The MaxiScan 2300 VS 5

front view

Presentation mode:

top view

1 cm

optimal

reading zone

9 cm

30 cm

scanner in

presentation mode

special offer

chewing-gum

1

2

1. Move the label to the scanner.

Bar code is read (green led).

2. Move the label from the scanner.

☞

Pollux manual deel_1 03-11-2000 10:27 Pagina 5

1.3 SCANNER LABELLING

Two labels are present on the housing of the MaxiScan 2300 VS as indicated in

the figure below. Two labels are also visible through the scanner window. All

labels are attached by the manufacturer and should not be removed.

The scanner’s serial number is found underneath the bar code label as depicted

in the figure above. This official registration number is strictly related to the

device. The supplier may ask for this number when the scanner needs servicing.

6 The MaxiScan 2300 VS

CAUTION-Laser light when open

Do not stare into beam

IEC825 class 1 laser product

Complies with 21CFR1040 as applicable to

a class IIa laser product. Avoid long

term viewing of direct laser light

Pollux manual deel_1 03-11-2000 10:27 Pagina 6

Laser safety

English:

The M2300 VS scanner complies with safety standard IEC 825-1 (1993) for a

Class I laser product. It also complies with U.S. 21CFR1040 as applicable to a

Class IIa laser product. Avoid long term viewing of direct laser light.

German:

Der Strichcode-Scanner M2300 VS entspricht den Sicherheitsvorschriften nach

IEC 825-1 (1993) für ein Laserprodukt der Klasse I. Er entspricht auch U.S.

21CFR1040, anwendbar auf ein Laserprodukt der Klasse IIa. Vermeiden Sie

langzeitiges Hineinblicken in direktes Laserlicht.

Dutch:

De M2300 VS scanner voldoet aan de veiligheidsnormen IEC 825-1 (1993) voor

een Klasse I laserprodukt. Tevens voldoet de scanner aan U.S. 21CFR1040, van

toepassing op een Klasse IIa laserprodukt. Vermijd langdurig kijken in direkt

laserlicht.

French:

Le scanner M2300 VS est conforme aux normes de sécurité IEC 825-1 (1993)

s’appliquant à un produit laser de la classe I. Il est également conforme à la U.S.

21CFR1040 telle qu’elle s’applique à un produit laser de la classe IIa. Eviter de

rester exposé longtemps à la lumière directe du laser.

Danish:

M2300 VS skanneren er i overensstemmelse med sikkerhedsstandarden IEC

825-1 (1993) for laserprodukter i klasse I. Den er også i overensstemmelse

med U.S. 21CFR1040, der gælder for laserprodukter i klasse IIa. Undgå at se

direkte på laserlys i længere perioder.

Finnish:

M2300 VS -skanneri täyttää luokan I lasertuotteelle IEC 825-1:ssä (1993)

asetetut turvavaatimukset. Se täyttää myös U.S. 21CFR1040:ssa asetetut

vaatimukset siltä osin kuin ne koskevat luokan IIa lasertuotetta. Vältä

pitkäaikaista suoraan laservaloon katsomista.

Swedish:

Avsökaren M2300 VS uppfyller säkerhetsnormen IEC 825-1 (1993)

för laserprodukter av klass 1. Den uppfyller dessutom U.S. 21CFR1040 som

gäller för laserprodukter av klass IIa. Undvik att titta i direkt laserljus under

längre perioder.

The MaxiScan 2300 VS 7

Pollux manual deel_1 03-11-2000 10:27 Pagina 7

8 The MaxiScan 2300 VS

Norwegian:

M2300 VS skanneren er i samsvar med sikkerhetsstandarden IEC 825-1 (1993)

for laserprodukter i klasse I. Den er også i samvar med U.S. 21CFR1040 for

laserprodukter i klasse IIa. Unngå å se langvarig på direkte laserlys.

Italian:

Lo scanner M2300 VS è conforme alle norme di sicurezza IEC 825-1 (1993)

relative ad un prodotto laser di Classe 1. È inoltre conforme alla norma U.S.

21CFR1040 relativa ad un prodotto laser di Classe IIa. Evitare l'esposizione

prolungata all'emissione diretta di luce laser.

Portuguese:

O scanner M2300 VS está conforme as normas de segurança IEC 825-1

(1993) para a Classe 1 dos produtos laser. Também está conforme a norma

U.S. 21CFR1040 aplicada nos produtos laser da Classe IIa. Evite expor os

olhos directa e prolongadamente aos raios laser.

Spanish:

El scanner M2300 VS reune las normas de seguridad IEC 825-1 (1993) para un

producto laser de Clase 1. Y también reune las normas U.S. 21CFR1040 que

se aplican a un producto laser de Clase IIa. Se debe evitar mirar muy fijo en luz

lasérica directa.

Optical: The use of optical instruments with this product will increase eye ha-

zard. Optical instruments include binoculars, microscopes and magnifying glas-

ses but do not include eye glasses worn by the user.

Radiant Energy: The M2300 VS uses a low-power laser diode operating at

675 nm in an opto-mechanical scanner resulting in less than 0.5 mW peak

output power. Laser light observed at 3,5 cm (1.38 in.) above the window

through a 7 mm (0.28 in.) aperture and averaged over 1000 seconds is less

than 3.9 µW per CDRH Class IIa specification. Do not attempt to remove the

protective housing of the scanner, as unscanned laser light with a peak output

up to 0.7 mW could be accessible inside.

Laser Light Viewer: The scanner window is the only aperture through which

laser light may be observed on this product.

A failure of the scanner motor, while the laser diode continues to emit a laser

beam, may cause emission levels to exceed those for safe operation. The

scanner has safeguards to prevent this occurrence. If, however, a stationary

laser beam is emitted, the failing scanner should be disconnected from its

power source immediately.

Pollux manual deel_1 03-11-2000 10:27 Pagina 8

Adjustments: Do not attempt any adjustments to or alteration of this product.

Do not remove the scanner’s protective housing. There are no user-serviceable

parts inside.

CAUTION: Use of controls or adjustments or performance of procedures

other than those specified herein may result in hazardous laser light

exposure.

1.4 MAINTAINING THE SCANNER

The MaxiScan 2300 VS scanner requires little maintenance. Only occasional

cleaning of the scanner window is necessary to remove dirt and fingerprints.

Cleaning can be performed during operation with a non-abrasive glass spray

cleaner and a soft lint-free cloth.

1.5 CONTROLLING THE SCANNER FROM THE POS SYSTEM

The MaxiScan 2300 VS can be controlled from the POS system via the RS232C

interface. Controlling is achieved by transmitting the following single byte

commands to the scanner. In the Scantech default setting the following

commands are available (more details upon request):

When the scanner is disabled, the motor of the scanner will stay on until the

scanner goes into sleep mode.

The MaxiScan 2300 VS 9

ASCII code

0E Hex

0F Hex

05 Hex

function

enable (cancels disable)

disable

power-up re-initialization

byte is also called:

Shift Out or <Ctrl-N>

Shift In or <Ctrl-O>

ENQ or <Ctrl-E>

12 Hex

sleep

DC2 or <Ctrl-R>

14 Hex

wake (cancels sleep)

DC4 or <Ctrl-T>

Pollux manual deel_1 03-11-2000 10:27 Pagina 9

10 The MaxiScan 2300 VS

POS system

+12V dc

- 12V dc

+ 5V dc

Maxiscan 2300 VS

Scanner control

Pollux manual deel_1 03-11-2000 10:27 Pagina 10

Chapter 2

Installing the MaxiScan 2300 VS

Pollux manual deel_1 03-11-2000 10:27 Pagina 11

12 Installing the MaxiScan 2300 VS

Depending on the way you want to use the MaxiScan 2300 VS, the scanner can

be installed fixed on a counter surface, sunk into the counter surface or on a

flexible stand.

The Maxiscan can be installed in two different ways, scanner housing

Landscape

or scanner housing

Portrait

(see the illustrations below). Refer to

chapter 3 for the various mounting options of the MaxiScan.

Independent from the installation you can direct the scan pattern in a way that

suits your application most, thanks to the four directional optical assembly. For

turning the optical assembly please refer to the MaxiScan 2300 VS Service

Manual (authorized personnel only).

Scanner Housing Landscape Scanner Housing Portrait

Cable supply

90/180/270

The turning of the optical assembly.

Note:The orientation of the scanner’s optical

assembly is factory assembled according to

your preference!

■ To make the instructions in this manual as clear as possible, the starting

point for all instructions is the landscape scanner housing setup.

IMPORTANT

Pollux manual deel_1 03-11-2000 10:27 Pagina 12

Instructions for installation on a counter surface are given in Section 2.1.

Instructions for installation on the flexible stand are given in Section 2.2.

Due to many POS systems on the market, a large number of communication

cables is available. Make sure that you have the right cable to connect the

scanner to your POS or computer.

2.1 INSTALLING THE SCANNER ON A COUNTER SURFACE

Follow these steps to mount the scanner in a fixed counter surface position:

1. Locate the optimal scanner position on the counter surface. Pay attention to

the product flow, distance to the counter edge and convenience for the

operator.

2. Use the enclosed templates of the vertical mount to mark the places for the

mounting holes at the counter surface and also the hole for the cable supply.

You can also choose to lead the cables away on the counter surface by

removing an insert in the back cover of the scanner.

Note:

- Use template A for installing the scanner housing landscape.

- Use template B for installing the scanner housing portrait.

3. Fasten the vertical mount to the surface with four screws (or four nuts and

bolts) as illustrated in the figure.

Installing the MaxiScan 2300 VS 13

■ The scanner and the host system must be switched off before starting the

installation of the scanner. By following this precaution you prevent any

electrical damage.

■ You are advised to install the scanner in an air circulated place out of direct

sunlight.

NOTES

SCANNER FRONT

Pollux manual deel_1 03-11-2000 10:27 Pagina 13

4. Locate the small hole at the back cover of the scanner. Remove the back

1. cover by pressing it with a coin as indicated in the figure.

5. Lead the power supply cable and communication cable through the hole in

the counter.

6. Plug the communication cable with the 8 pin modular jack into Data port 1 if

the host system features the RS232C or IBM RS485 interface, or into Data

port 2 if the host system features the OCIA or KBW interface. Plug the other

connector of the cable into the appropriate serial port of your POS or

computer. Connect the Intermec universal power supply unit to the power

supply port. Lead the cables through the scanner as illustrated in the figure

on the next page.

14 Installing the MaxiScan 2300 VS

insert

Pollux manual deel_1 03-11-2000 10:27 Pagina 14

Installing the MaxiScan 2300 VS 15

AUX INTERFACE INTERFACE POWER

PORT 2 PORT 1

AUX INTERFACE INTERFACE POWER

PORT 2 PORT 1

Interface port 1. Connect the communication

cable to this port if the host system features

the RS232C or IBM RS 485 interface

AUX INTERFACE INTERFACE POWER

PORT 2 PORT 1

Interface port 2. Connect the communication

cable to this port if the host system features

the OCIA or KBW interface

Pollux manual deel_1 03-11-2000 10:27 Pagina 15

7. Place the scanner on the vertical mount as illustrated in the figure.

8. Reposition the back cover of the scanner.

9. Power on the scanner by connecting the IEC power cord to the AC/DC power

supply and plugging the AC power cord into an AC power outlet. Switch on

the host system.

Once the scanner is installed, you can start scanning bar code labels. If you

want to change the default settings of the scanner, proceed to the Configuration

Guide which came with the scanner.

16 Installing the MaxiScan 2300 VS

AUX INTERFACE INTERFACE POWER

PORT 2 PORT 1

SCANNER FRONT

■ To activate Data port 2 (OCIA or KBW interface) scan the following codes

from the Configuration Guide:

1. open the scanner Programming Mode by scanning code 1.1

2. return to factory default settings by scanning code 1.3

IMPORTANT

Pollux manual deel_1 03-11-2000 10:27 Pagina 16

La pagina sta caricando ...

Intermec MaxiScan 2300 Manuale utente

Questo manuale è adatto anche per

Intermec MaxiScan 2300 Manuale utente

in altre lingue

Documenti correlati

Altri documenti