Intermec MaxiScan 2300 Manuale utente

Categoria
Lettori di codici a barre
Tipo
Manuale utente

Questo manuale è adatto anche per

User's manual
Intermec MaxiScan 2300 VS
Pollux manual deel_1 03-11-2000 10:27 Pagina a
Regulatory Statements
CE Intermec hereby declares that the MaxiScan 2300 VS has been tested and found compliant with
the below listed standards as required by the EMC Directive 89/336EEC as amended by 92/31/EEC
and by the Low Voltage Directive 73/23/EEC as amended by 93/68/EEC:
EN 55022 (1992)
EN 50082 (1998)
EN 60950 (1993)
USA: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. It generates, uses and can radiate radio frequency energy. If not
installed and used in accordance with the instructions, it may cause interference to radio
communications. If this equipment causes interference, the user will be required to correct the
interference at the user’s own expense.
This equipment complies with the UL 1950 standard.
Canada: This Class B digital apparatus meets all requirements of the Canadian Interference Causing
Equipment Regulations.
Cet appareil numerique de la classe B respect toutes les exigences du Reglement sur le materiel
brouilleur du Canada.
This equipment complies with the UL 1950 standard.
Cet equipment ext conforme a la norme UL 1950.
Mexico: Este equipo cumple con la certification NOM.
Australia –New Zealand: This equipment has been tested and found to conform to the Australian EMC
framework concerning Class B digital devices, prescribed by the Australian and New-Zealand standard
AS/NZS 3548.
The information contained in this document is for informational purposes only and is subject to change
without notice. No part of this document may be copied or reproduced in any manner without the prior
written permission of Intermec Technologies Corporation.
The word Intermec, the Intermec logo, Scanplus and EasySet are either trademarks or registered
trademarks of Intermec.
Throughout this document, trademarked names may be used. Rather than put a trademark (tm or R)
symbol in every occurrence of a trademarked name, we state that we are using the names only in an
editorial fashion, an do the benefit of the trademark owner, with no intention of infringement.
P/N 3-450049-01 October 2000
Pollux manual deel_1 03-11-2000 10:27 Pagina b
Table of contents
Preface i
Chapter 1 The MaxiScan 2300 VS 1
1.1 Unpacking the MaxiScan 2300 VS 2
1.2 Scanning bar codes with the MaxiScan 2300 VS 4
1.3 Scanner labelling 6
1.4 Maintaining the scanner 9
1.5 Controlling the scanner from the POS system 9
Chapter 2 Installing the MaxiScan 2300 VS 11
2.1 Installing the scanner on a counter surface 13
2.2 Installing the scanner using the flexible stand 17
Chapter 3 Mounting options MaxiScan 2300 VS 21
3.1 Flyby mode scanning: right to left 23
3.2 Flyby mode scanning: left to right 25
3.3 Presentation mode scanning 27
Appendices A. Connector types and pin definitions 30
B. Technical specifications 32
C. Troubleshooting 33
Pollux manual deel_1 03-11-2000 10:27 Pagina c
Preface
The MaxiScan 2300 VS is an innovative, high performance food retail scanner,
combining unequalled performances with enormous installation flexibility. It has a
unique four-directional sealed optical assembly, allowing it to be turned inside
the fixed scanner housing. This new benchmark for vertical supermarket and
hypermarket scanning ensures an ergonomic and user-friendly implementation
wherever it is installed. The MaxiScan is also one of the flattest scanners
available today, making installation at the check-out even easier.
Two versions of the MaxiScan are available, one unit has RS232C and OCIA
interfaces and the other has IBM RS485 and Keyboard Wedge interfaces. An
auxiliary port for connecting another scanner is standard.
This manual contains three chapters and three appendices. The first chapter
describes the MaxiScan 2300 VS and its general features. The MaxiScan can be
installed on a counter surface or on a flexible stand. Instructions for the
installation are described in the second chapter. Precisely follow the instructions
for the installation of the scanner. Default settings can be changed with the bar
code labels from the Configuration Guide that came with the scanner. The third
chapter describes all possible mounting options. Appendix A shows all
connectors of the scanner. Technical specifications of the MaxiScan 2300 VS
can be found in Appendix B. Refer to Appendix C for troubleshooting if the
scanner is not working properly.
Pollux manual deel_1 03-11-2000 10:27 Pagina d
Chapter 1
The MaxiScan 2300 VS
Pollux manual deel_1 03-11-2000 10:27 Pagina e
1.1 UNPACKING THE MAXISCAN 2300 VS
Remove the scanner and its accessories from the box and packing material.
Refer to the packing list to make sure you have received all the items ordered.
Visually inspect the scanner and accessories for any evidence of physical
damage. Refer to the figure on page 6 to locate the interface label and make
sure that the scanner interface corresponds with the host system interface.
Immediately contact your supplier if anything appears to be damaged, or if the
supported interface does not correspond with the host system interface.
The various parts of the MaxiScan 2300 VS are:
2 The MaxiScan 2300 VS
LED
Sleep mode switch
THE Maxiscan 2300 VS
Good read speaker
Pollux manual deel_1 03-11-2000 10:27 Pagina 2
The various parts of the MaxiScan 2300 VS are:
Sleep mode switch - When a sleep mode time-out is programmed, the -
scanner can be re-activated by pressing this switch.
The sleep-mode feature is programmable with the
menu labels from the Configuration Guide.
NOTE: The default value for the sleep mode time-out
is set to 30 minutes. When the scanner is in
sleep mode, the LED is intermittently flashing
red.
LED - A red LED indicates that the scanner is ready to read
a bar code. A green LED indicates a good read.
Good read speaker - The speaker is heard whenever data has been read
correctly. The frequency and volume can be adjusted
with the menu labels from the Configuration Guide.
The MaxiScan 2300 VS 3
Pollux manual deel_1 03-11-2000 10:27 Pagina 3
1.2 SCANNING BAR CODES WITH THE MAXISCAN 2300 VS
The MaxiScan 2300 VS is an omni-directional scanner featuring a 5 directional
scan field with a 20 lines scan pattern. The scanner's scan volume is illustrated
in the figure below. The optimal reading zone lies between 1 and 9 cm from the
scanner window, but bar codes can be read up to 30 cm (11.8 in.) from the
scanner window. The scanner can be used in either fly by or presentation mode.
Scanning a bar code label in fly by mode is very simple: pass the product’s bar
code label along the scanner as illustrated in the figure below.
4 The MaxiScan 2300 VS
front view
Fly by mode:
scan pattern
volume
1 cm
optimal
reading zone
top view
9 cm
30 cm
product flow
scanner in
fly by mode
1. Pass the label along the scanner.
Bar code is read (green led).
1
special offer
chewing-gum
Pollux manual deel_1 03-11-2000 10:27 Pagina 4
Scanning a bar code label in presentation mode is also very simple: present the
product’s bar code label to the scanner as illustrated in the figure below.
The MaxiScan 2300 VS 5
front view
Presentation mode:
top view
1 cm
optimal
reading zone
9 cm
30 cm
scanner in
presentation mode
special offer
chewing-gum
1
2
1. Move the label to the scanner.
Bar code is read (green led).
2. Move the label from the scanner.
Pollux manual deel_1 03-11-2000 10:27 Pagina 5
1.3 SCANNER LABELLING
Two labels are present on the housing of the MaxiScan 2300 VS as indicated in
the figure below. Two labels are also visible through the scanner window. All
labels are attached by the manufacturer and should not be removed.
The scanner’s serial number is found underneath the bar code label as depicted
in the figure above. This official registration number is strictly related to the
device. The supplier may ask for this number when the scanner needs servicing.
6 The MaxiScan 2300 VS
CAUTION-Laser light when open
Do not stare into beam
IEC825 class 1 laser product
Complies with 21CFR1040 as applicable to
a class IIa laser product. Avoid long
term viewing of direct laser light
Pollux manual deel_1 03-11-2000 10:27 Pagina 6
Laser safety
English:
The M2300 VS scanner complies with safety standard IEC 825-1 (1993) for a
Class I laser product. It also complies with U.S. 21CFR1040 as applicable to a
Class IIa laser product. Avoid long term viewing of direct laser light.
German:
Der Strichcode-Scanner M2300 VS entspricht den Sicherheitsvorschriften nach
IEC 825-1 (1993) für ein Laserprodukt der Klasse I. Er entspricht auch U.S.
21CFR1040, anwendbar auf ein Laserprodukt der Klasse IIa. Vermeiden Sie
langzeitiges Hineinblicken in direktes Laserlicht.
Dutch:
De M2300 VS scanner voldoet aan de veiligheidsnormen IEC 825-1 (1993) voor
een Klasse I laserprodukt. Tevens voldoet de scanner aan U.S. 21CFR1040, van
toepassing op een Klasse IIa laserprodukt. Vermijd langdurig kijken in direkt
laserlicht.
French:
Le scanner M2300 VS est conforme aux normes de sécurité IEC 825-1 (1993)
s’appliquant à un produit laser de la classe I. Il est également conforme à la U.S.
21CFR1040 telle qu’elle s’applique à un produit laser de la classe IIa. Eviter de
rester exposé longtemps à la lumière directe du laser.
Danish:
M2300 VS skanneren er i overensstemmelse med sikkerhedsstandarden IEC
825-1 (1993) for laserprodukter i klasse I. Den er også i overensstemmelse
med U.S. 21CFR1040, der gælder for laserprodukter i klasse IIa. Undgå at se
direkte på laserlys i længere perioder.
Finnish:
M2300 VS -skanneri täyttää luokan I lasertuotteelle IEC 825-1:ssä (1993)
asetetut turvavaatimukset. Se täyttää myös U.S. 21CFR1040:ssa asetetut
vaatimukset siltä osin kuin ne koskevat luokan IIa lasertuotetta. Vältä
pitkäaikaista suoraan laservaloon katsomista.
Swedish:
Avsökaren M2300 VS uppfyller säkerhetsnormen IEC 825-1 (1993)
för laserprodukter av klass 1. Den uppfyller dessutom U.S. 21CFR1040 som
gäller för laserprodukter av klass IIa. Undvik att titta i direkt laserljus under
längre perioder.
The MaxiScan 2300 VS 7
Pollux manual deel_1 03-11-2000 10:27 Pagina 7
8 The MaxiScan 2300 VS
Norwegian:
M2300 VS skanneren er i samsvar med sikkerhetsstandarden IEC 825-1 (1993)
for laserprodukter i klasse I. Den er også i samvar med U.S. 21CFR1040 for
laserprodukter i klasse IIa. Unngå å se langvarig på direkte laserlys.
Italian:
Lo scanner M2300 VS è conforme alle norme di sicurezza IEC 825-1 (1993)
relative ad un prodotto laser di Classe 1. È inoltre conforme alla norma U.S.
21CFR1040 relativa ad un prodotto laser di Classe IIa. Evitare l'esposizione
prolungata all'emissione diretta di luce laser.
Portuguese:
O scanner M2300 VS está conforme as normas de segurança IEC 825-1
(1993) para a Classe 1 dos produtos laser. Também está conforme a norma
U.S. 21CFR1040 aplicada nos produtos laser da Classe IIa. Evite expor os
olhos directa e prolongadamente aos raios laser.
Spanish:
El scanner M2300 VS reune las normas de seguridad IEC 825-1 (1993) para un
producto laser de Clase 1. Y también reune las normas U.S. 21CFR1040 que
se aplican a un producto laser de Clase IIa. Se debe evitar mirar muy fijo en luz
lasérica directa.
Optical: The use of optical instruments with this product will increase eye ha-
zard. Optical instruments include binoculars, microscopes and magnifying glas-
ses but do not include eye glasses worn by the user.
Radiant Energy: The M2300 VS uses a low-power laser diode operating at
675 nm in an opto-mechanical scanner resulting in less than 0.5 mW peak
output power. Laser light observed at 3,5 cm (1.38 in.) above the window
through a 7 mm (0.28 in.) aperture and averaged over 1000 seconds is less
than 3.9 µW per CDRH Class IIa specification. Do not attempt to remove the
protective housing of the scanner, as unscanned laser light with a peak output
up to 0.7 mW could be accessible inside.
Laser Light Viewer: The scanner window is the only aperture through which
laser light may be observed on this product.
A failure of the scanner motor, while the laser diode continues to emit a laser
beam, may cause emission levels to exceed those for safe operation. The
scanner has safeguards to prevent this occurrence. If, however, a stationary
laser beam is emitted, the failing scanner should be disconnected from its
power source immediately.
Pollux manual deel_1 03-11-2000 10:27 Pagina 8
Adjustments: Do not attempt any adjustments to or alteration of this product.
Do not remove the scanner’s protective housing. There are no user-serviceable
parts inside.
CAUTION: Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous laser light
exposure.
1.4 MAINTAINING THE SCANNER
The MaxiScan 2300 VS scanner requires little maintenance. Only occasional
cleaning of the scanner window is necessary to remove dirt and fingerprints.
Cleaning can be performed during operation with a non-abrasive glass spray
cleaner and a soft lint-free cloth.
1.5 CONTROLLING THE SCANNER FROM THE POS SYSTEM
The MaxiScan 2300 VS can be controlled from the POS system via the RS232C
interface. Controlling is achieved by transmitting the following single byte
commands to the scanner. In the Scantech default setting the following
commands are available (more details upon request):
When the scanner is disabled, the motor of the scanner will stay on until the
scanner goes into sleep mode.
The MaxiScan 2300 VS 9
ASCII code
0E Hex
0F Hex
05 Hex
function
enable (cancels disable)
disable
power-up re-initialization
byte is also called:
Shift Out or <Ctrl-N>
Shift In or <Ctrl-O>
ENQ or <Ctrl-E>
12 Hex
sleep
DC2 or <Ctrl-R>
14 Hex
wake (cancels sleep)
DC4 or <Ctrl-T>
Pollux manual deel_1 03-11-2000 10:27 Pagina 9
10 The MaxiScan 2300 VS
POS system
+12V dc
- 12V dc
+ 5V dc
Maxiscan 2300 VS
Scanner control
Pollux manual deel_1 03-11-2000 10:27 Pagina 10
Chapter 2
Installing the MaxiScan 2300 VS
Pollux manual deel_1 03-11-2000 10:27 Pagina 11
12 Installing the MaxiScan 2300 VS
Depending on the way you want to use the MaxiScan 2300 VS, the scanner can
be installed fixed on a counter surface, sunk into the counter surface or on a
flexible stand.
The Maxiscan can be installed in two different ways, scanner housing
Landscape
or scanner housing
Portrait
(see the illustrations below). Refer to
chapter 3 for the various mounting options of the MaxiScan.
Independent from the installation you can direct the scan pattern in a way that
suits your application most, thanks to the four directional optical assembly. For
turning the optical assembly please refer to the MaxiScan 2300 VS Service
Manual (authorized personnel only).
Scanner Housing Landscape Scanner Housing Portrait
Cable supply
Cable supply
90/180/270
90/180/270
The turning of the optical assembly.
Note:The orientation of the scanner’s optical
assembly is factory assembled according to
your preference!
To make the instructions in this manual as clear as possible, the starting
point for all instructions is the landscape scanner housing setup.
IMPORTANT
Pollux manual deel_1 03-11-2000 10:27 Pagina 12
Instructions for installation on a counter surface are given in Section 2.1.
Instructions for installation on the flexible stand are given in Section 2.2.
Due to many POS systems on the market, a large number of communication
cables is available. Make sure that you have the right cable to connect the
scanner to your POS or computer.
2.1 INSTALLING THE SCANNER ON A COUNTER SURFACE
Follow these steps to mount the scanner in a fixed counter surface position:
1. Locate the optimal scanner position on the counter surface. Pay attention to
the product flow, distance to the counter edge and convenience for the
operator.
2. Use the enclosed templates of the vertical mount to mark the places for the
mounting holes at the counter surface and also the hole for the cable supply.
You can also choose to lead the cables away on the counter surface by
removing an insert in the back cover of the scanner.
Note:
- Use template A for installing the scanner housing landscape.
- Use template B for installing the scanner housing portrait.
3. Fasten the vertical mount to the surface with four screws (or four nuts and
bolts) as illustrated in the figure.
Installing the MaxiScan 2300 VS 13
The scanner and the host system must be switched off before starting the
installation of the scanner. By following this precaution you prevent any
electrical damage.
You are advised to install the scanner in an air circulated place out of direct
sunlight.
NOTES
SCANNER FRONT
Pollux manual deel_1 03-11-2000 10:27 Pagina 13
4. Locate the small hole at the back cover of the scanner. Remove the back
1. cover by pressing it with a coin as indicated in the figure.
5. Lead the power supply cable and communication cable through the hole in
the counter.
6. Plug the communication cable with the 8 pin modular jack into Data port 1 if
the host system features the RS232C or IBM RS485 interface, or into Data
port 2 if the host system features the OCIA or KBW interface. Plug the other
connector of the cable into the appropriate serial port of your POS or
computer. Connect the Intermec universal power supply unit to the power
supply port. Lead the cables through the scanner as illustrated in the figure
on the next page.
14 Installing the MaxiScan 2300 VS
insert
insert
Pollux manual deel_1 03-11-2000 10:27 Pagina 14
Installing the MaxiScan 2300 VS 15
AUX INTERFACE INTERFACE POWER
PORT 2 PORT 1
AUX INTERFACE INTERFACE POWER
PORT 2 PORT 1
Interface port 1. Connect the communication
cable to this port if the host system features
the RS232C or IBM RS 485 interface
AUX INTERFACE INTERFACE POWER
PORT 2 PORT 1
Interface port 2. Connect the communication
cable to this port if the host system features
the OCIA or KBW interface
Pollux manual deel_1 03-11-2000 10:27 Pagina 15
7. Place the scanner on the vertical mount as illustrated in the figure.
8. Reposition the back cover of the scanner.
9. Power on the scanner by connecting the IEC power cord to the AC/DC power
supply and plugging the AC power cord into an AC power outlet. Switch on
the host system.
Once the scanner is installed, you can start scanning bar code labels. If you
want to change the default settings of the scanner, proceed to the Configuration
Guide which came with the scanner.
16 Installing the MaxiScan 2300 VS
To activate Data port 2 (OCIA or KBW interface) scan the following codes
from the Configuration Guide:
1. open the scanner Programming Mode by scanning code 1.1
2. return to factory default settings by scanning code 1.3
IMPORTANT
Pollux manual deel_1 03-11-2000 10:27 Pagina 16
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

Intermec MaxiScan 2300 Manuale utente

Categoria
Lettori di codici a barre
Tipo
Manuale utente
Questo manuale è adatto anche per

in altre lingue