Yamaha RX-V1700 Manuale del proprietario

YAMAHA ELECTRONICS CORPORATION, USA

6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD.

135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H.

SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A.

RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD.

YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND

YAMAHA SCANDINAVIA A.B.

J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD.

17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

©

RX-V1700

Printed in Malaysia WH63600

RX-V1700

AV Receiver

Ampli-tuner audio-vidéo

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

GEBRUIKSAANWIJZING

ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ

G

RX-V1700_G_cv.fm Page 1 Thursday, August 24, 2006 11:29 AM

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry, clean

place – away from direct sunlight, heat sources, vibration,

dust, moisture, and/or cold. Allow ventilation space of at least

30 cm on the top, 20 cm on the left and right, and 20 cm on

the back of this unit.

3 Locate this unit away from other electrical appliances, motors,

or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in an environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign objects may fall onto

this unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to

this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature

inside this unit rises, it may cause fire, damage to this unit,

and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections

are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and may

cause fire, damage to this unit, and/or personal injury.

YAMAHA will not be held responsible for any damage

resulting from use of this unit with a voltage other than

specified.

13 To prevent damage by lightning, keep the power cord and

outdoor antennas disconnected from a wall outlet or the unit

during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact qualified

YAMAHA service personnel when any service is needed. The

cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time

(i.e. vacation), disconnect the AC power plug from the wall

outlet.

16 Install this unit near the AC outlet and where the AC power

plug can be reached easily.

17 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit is

faulty.

18 Before moving this unit, press MASTER ON/OFF to release it

outward to the OFF position to turn off this unit, the main

room, Zone 2 and Zone 3 and then disconnect the AC power

plug from the AC wall outlet.

19 VOLTAGE SELECTOR (Asia and General models only)

The VOLTAGE SELECTOR on the rear panel of this unit

must be set for your local main voltage BEFORE plugging

into the AC main supply. Voltages are:

Asia model ................................ AC 220/230–240 V, 50/60 Hz

General model.............AC 110/120/220/230–240 V, 50/60 Hz

■ For U.K. customers

If the socket outlets in the home are not suitable for the

plug supplied with this appliance, it should be cut off and

an appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

The plug severed from the mains lead must be destroyed, as a

plug with bared flexible cord is hazardous if engaged in a live

socket outlet.

■ Special Instructions for U.K. Model

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN

OR MOISTURE.

As long as this unit is connected to the AC wall outlet,

it is not disconnected from the AC power source even

if you turn off this unit by MASTER ON/OFF. In this

state, this unit is designed to consume a very small

quantity of power.

Note

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured

markings identifying the terminals in your plug,

proceed as follows:

The wire which is coloured BLUE must be connected

to the terminal which is marked with the letter N or

coloured BLACK. The wire which is coloured

BROWN must be connected to the terminal which is

marked with the letter L or coloured RED.

Making sure that neither core is connected to the earth

terminal of the three pin plug.

1 En

PREPARATIONINTRODUCTION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

English

FEATURES............................................................. 2

GETTING STARTED............................................ 3

Supplied accessories .................................................. 3

CONTROLS AND FUNCTIONS ......................... 4

Front panel ................................................................. 4

Remote control........................................................... 6

Zone 2/Zone 3 remote control ................................... 8

Preparing the remote control ..................................... 9

Front panel display .................................................. 10

Rear panel ................................................................ 12

CONNECTIONS .................................................. 13

Placing speakers....................................................... 13

Connecting speakers ................................................ 14

Using bi-amplification connections......................... 17

Information on jacks and cable plugs ...................... 18

Information on HDMI.............................................. 19

Audio and video signal flow.................................... 20

Connecting a TV monitor or projector .................... 21

Connecting other components ................................. 22

Connecting a multi-format player

or an external decoder ......................................... 26

Connecting a YAMAHA iPod universal dock ........ 27

Using the VIDEO AUX jacks on the front panel .... 27

Connecting the FM and AM antennas ..................... 28

Connecting the power cable..................................... 29

Setting the speaker impedance................................. 30

Turning on and off the power .................................. 31

AUTO SETUP....................................................... 32

Using AUTO SETUP .............................................. 32

PLAYBACK.......................................................... 38

Basic procedure ....................................................... 38

Selecting audio input jacks

(AUDIO SELECT).............................................. 40

Selecting the MULTI CH INPUT component......... 41

Using your headphones............................................ 41

Muting the audio output........................................... 41

Displaying the input source information ................. 42

Playing video sources

in the background of an audio source.................. 43

Using the sleep timer ............................................... 43

SOUND FIELD PROGRAMS............................. 44

Selecting sound field programs ............................... 44

Sound field program descriptions............................ 45

Enjoying unprocessed input sources........................ 49

USING AUDIO FEATURES............................... 50

Enjoying pure hi-fi sound ........................................ 50

Adjusting the tonal quality....................................... 50

Adjusting the speaker level...................................... 51

Enjoying multi-channel sources

in 2-channel stereo............................................... 51

Selecting the Compressed Music

Enhancer mode ................................................... 52

Selecting the night listening mode........................... 53

FM/AM TUNING..................................................54

FM/AM controls and functions ............................... 54

Automatic tuning ..................................................... 56

Manual tuning.......................................................... 57

Automatic preset tuning........................................... 58

Manual preset tuning ............................................... 59

Selecting preset stations........................................... 60

Exchanging preset stations ...................................... 61

RADIO DATA SYSTEM TUNING

(U.K. AND EUROPE MODELS ONLY)........62

Displaying the Radio Data System information ...... 62

Selecting the Radio Data System program type

(PTY SEEK mode).............................................. 63

Using the enhanced other networks (EON)

data service .......................................................... 64

USING iPod ...........................................................66

Controlling iPod ...................................................... 66

RECORDING........................................................68

ADVANCED SOUND CONFIGURATIONS.....69

Changing sound field parameter settings................. 69

Selecting decoders ................................................... 73

CUSTOMIZING THIS UNIT

(MANUAL SETUP) ..........................................77

Using SET MENU................................................... 79

1 BASIC MENU...................................................... 80

2 SOUND MENU.................................................... 84

3 INPUT MENU...................................................... 87

4 OPTION MENU................................................... 90

REMOTE CONTROL FEATURES ...................94

Controlling this unit, a TV,

or other components ............................................ 94

Setting remote control codes ................................... 96

Programming codes from other remote controls ..... 98

Changing source names in the display window....... 99

Macro programming features ................................ 100

Clearing configurations ......................................... 103

USING MULTI-ZONE CONFIGURATION...106

Connecting the Zone 2 and Zone 3 components ... 106

Controlling Zone 2 or Zone 3 ................................ 107

ADVANCED SETUP..........................................110

Using ADVANCED SETUP ................................. 110

Setting remote control ID ...................................... 112

TROUBLESHOOTING .....................................115

RESETTING THE SYSTEM.............................122

GLOSSARY.........................................................123

SOUND FIELD PROGRAM

INFORMATION .............................................126

PARAMETRIC EQUALIZER

INFORMATION .............................................127

SPECIFICATIONS.............................................128

CONTENTS

INTRODUCTION

PREPARATION

BASIC OPERATION

ADVANCED OPERATION

ADDITIONAL INFORMATION

APPENDIX (at the end of this manual)

• SOUND OUTPUT IN EACH SOUND FIELD PROGRAM

• LIST OF REMOTE CONTROL CODES

FEATURES

2 En

Built-in 7-channel power amplifier

◆ Minimum RMS output power

(20 Hz to 20 kHz, 0.04% THD, 8 Ω)

Front: 130 W + 130 W

Center: 130 W

Surround: 130 W + 130 W

Surround back: 130 W + 130 W

Sound field programs

◆ Proprietary YAMAHA technology for the creation of sound

fields

◆ Dolby Digital/Dolby Digital EX decoder

◆ DTS/DTS-ES Matrix 6.1, Discrete 6.1, DTS Neo:6,

DTS 96/24 decoder

◆ Dolby Pro Logic/Dolby Pro Logic II/Dolby Pro Logic IIx

decoder

◆ Virtual CINEMA DSP

◆ SILENT CINEMA

Sophisticated AM/FM tuner

◆ 40-station random and direct preset tuning

◆ Automatic preset tuning

◆ Preset station shifting capability (preset editing)

◆ Radio Data System capability (U.K. and Europe models only)

HDMI (High-Definition Multimedia Interface)

◆ HDMI interface for standard, enhanced or

high-definition video (includes 1080p video signal

transmission) as well as multi-channel digital audio based on

HDMI version 1.2a

◆ Analog video to HDMI digital video up-conversion

(composite video ↔ S-video ↔ component video → HDMI

digital video) capability for monitor out

iPod controlling capability

◆ DOCK terminal to connect a YAMAHA iPod universal dock

(such as the YDS-10, sold separately), which supports iPod

(Click and Wheel), iPod nano, and iPod mini

Other features

◆ YPAO (YAMAHA Parametric Room Acoustic Optimizer) for

automatic speaker setup

◆ 192-kHz/24-bit D/A converter

◆ OSD (on-screen display) menus that allow you to optimize

this unit to suit your individual audiovisual system

◆ 6 or 8-channel additional input jacks for discrete multi-

channel input

◆ Analog video interlace/progressive conversion from 480i

(NTSC)/576i (PAL) to 480p/576p

◆ S-video signal input/output capability

◆ Component video input/output capability includes (3

COMPONENT VIDEO INs and 1 MONITOR OUT)

◆ Optical and coaxial digital audio signal jacks

◆ Pure Direct mode for pure hi-fi sound for all sources

◆ Cinema and music night listening modes

◆ Compressed Music Enhancer mode to improve the sound

quality of compression artifacts (such as the MP3 format) to

that of a high-quality stereo

◆ Remote control with preset remote control codes, learning and

macro capability

◆ ZONE 2/ZONE 3 custom installation facility

◆ Zone switching capability between the main zone and

ZONE 2/ZONE 3 using ZONE CONTROLS

◆ Sleep timer

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, and the double-D symbol are trademarks

of Dolby Laboratories.

Manufactured under license from Digital Theater Systems, Inc.

“DTS”, “DTS-ES”, “NEO:6”, and “DTS 96/24” are trademarks

“iPod” is a trademark of Apple Computer, Inc., registered in the

U.S. and other countries.

“HDMI”, the “HDMI” logo and “High-Definition Multimedia

Interface” are trademarks or registered trademarks of HDMI

Licensing LLC.

“SILENT CINEMA” is a trademark of YAMAHA

CORPORATION.

FEATURES

iPod

®

GETTING STARTED

3 En

INTRODUCTION

English

Check that you received all of the following parts.

GETTING STARTED

Supplied accessories

About this manual

• y indicates a tip for your operation.

• Some operations can be performed by using either the buttons on the front panel or the ones on the remote control. In case the

button names differ between the front panel and the remote control, the button name on the remote control is given in

parentheses.

• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements,

etc. In case of differences between the manual and product, the product has priority.

V

-

AUX/DOCK

–

+

––

+

ENTER

DISPLAY

AUDIO

MENU

TITLE

TV MUTE

TV INPUT

MUTE

4

3

2

ENT

+

10

0

9

5

1

AV

TV

7

6

8

RETURN

ON

OFF

CLEAR

LEARN

RENAME

MACRO

REC

DISC SKIP

VOLUME

CH

TV VOL

EFFECT

PARAMETER

STRAIGHT

A/B/C/D/E

SRCH MODE

PURE DIRECT

PRESET/CH

SET MENU

B

A

N

D

LEVEL

ENHANCER

STEREO

SUR. DECODE

SELECT

EXTD SUR.

CLASSICAL

LIVE/CLUB

ENTERTAIN

MOVIE

NIGHT

FREQ/TEXT

EON

MODE PTY SEEK

START

TV

SOURCE

AMP

SELECT

DTV

DVR/VCR 2

VCR 1

DVD

CBL/SAT

MD/TAPE

CD-R

PHONO

TUNER CD

MULTI CH IN

SLEEP

AUDIO SEL

POWER

STANDBY

Remote control

Batteries (6)

(AAA, R03, UM-4)

AM loop antenna

Optimizer microphoneSpeaker terminal wrench Power cable

Indoor FM antenna

(U.S.A., Canada, China, Asia,

General and Korea models)

Indoor FM antenna

(Europe, U.K. and Australia models)

TUNER

CD

CD-R

DTV

PHONO

CBL/SAT

MD/TAPE

VCR 1

DVD

V-AUX/DOCK

DVR/VCR 2

POWER

STANDBY

A/B/C/D/E

PRESET

VOLUME

ZONE 3

ZONE 2

ID2

ID1

MUTE

Zone 2/Zone 3

remote control

(except Europe model)

CONTROLS AND FUNCTIONS

4 En

This section describes only the amplifier controls and functions of this unit. See the following pages for details about

other control and functions.

• AM/FM tuning ........................... see page 54

1 MASTER ON/OFF

Turns this unit on or off (see page 31).

2 MAIN ZONE ON/OFF

Turns on the main zone or sets it to the standby mode

(see page 31).

• In the standby mode, this unit consumes a small amount of

power in order to receive infrared signals from the remote

control.

• When you turn on this unit, there will be a 4 to 5-second delay

before this unit can reproduce sound.

• This button is operational only when MASTER ON/OFF is

pressed inward to the ON position.

3 INPUT selector

Selects the desired input source (see page 38).

4 AUDIO SELECT

Toggles the priority for the type of audio input jack

between “AUTO”, “HDMI”, “COAX/OPT” and

“ANALOG” when one component is connected to two or

more input jacks (see page 40).

5 TONE CONTROL

Adjusts the bass/treble balance of the front left, front right

and center channels in conjunction with the PROGRAM

selector (see page 50).

6 STRAIGHT

Turns the sound field programs off or on. When the

“STRAIGHT” mode is selected, 2-channel or multi-

channel input signals are output directly from their

respective speakers without effect processing (see

page 49).

CONTROLS AND FUNCTIONS

Front panel

MASTER

PURE DIRECT

VOLUME

MAIN ZONE

INPUT

ON

OFF

ENHANCER

NIGHT

ZONE ON/OFF

ZONE CONTROLS

MODE

TUNING

PRESET/TUNING

EDIT

MULTI ZONE

FM/AM

TUNING

PRESET/

MAN'L/AUTO FM

MEMORY

MIC

OPTIMIZER

EFFECT

STRAIGHT

CONTROL

SELECT

AUDIO

TONE

A/B/C/D/E

PROGRAM

YPAO

ZONE 3

R

L

OPTICAL

ZONE 2

AUDIO

VIDEO AUX

SILENT CINEMA

S VIDEO

VIDEO

PHONES

ON/OFF

32 BA09

GFEDC

876541

Notes

CONTROLS AND FUNCTIONS

5 En

INTRODUCTION

English

7 MULTI ZONE buttons

ZONE 2 ON/OFF

Turns on Zone 2 only or sets it to the standby mode.

See page 107 for details.

ZONE 3 ON/OFF

Turns on Zone 3 only or sets it to the standby mode.

See page 107 for details.

These buttons are operational only when MASTER ON/OFF

is pressed inward to the ON position.

ZONE CONTROLS

Switches the zone you want to control between the

main zone, Zone 2 and Zone 3. See page 107 for

details.

y

After you press ZONE CONTROLS, the indicator for the

currently selected zone flashes in the front panel display for

approximately 5 seconds. While the indicator is flashing,

perform the desired operation.

8 Front panel display

Shows information about the operational status of this unit

(see page 10).

9 ENHANCER

Turns on or off the Compressed Music Enhancer mode

(see page 52).

0 Remote control sensor

Receives signals from the remote control (see page 9).

A NIGHT

Turns on or off the night listening modes (see page 53).

B PURE DIRECT

Turns on or off the Pure Direct mode (see page 50).

C PROGRAM selector

• Selects sound field programs (see page 44).

• Adjusts the bass/treble balance in conjunction with

TONE CONTROL (see page 50).

D OPTIMIZER MIC jack

Use to connect and input audio signals from the supplied

optimizer microphone in the “AUTO SETUP” procedure

(see page 32).

E PHONES jack

Outputs audio signals for private listening with

headphones (see page 41).

F VIDEO AUX jacks

Input audio and video signals from a portable external

source such as a game console or a video camera

(see page 27).

y

To reproduce the source signals input at these jacks, select

“V-AUX” as the input source.

The audio signals input at the DOCK terminal on the rear panel

take priority over the ones input at the VIDEO AUX jacks.

G VOLUME

Controls the output level of all audio channels.

y

This does not affect the AUDIO OUT (REC) level.

■ Opening and closing the front panel

door

When you want to use the controls behind the front panel

door, open the door by gently pressing on the lower part of

the panel. Keep the door closed when not using these

controls.

Note

To open, press gently on the lower part of the panel.

CONTROLS AND FUNCTIONS

6 En

■ Remote control controls and functions

This section describes only the amplifier controls and functions of this unit. See the following pages for details about

other control and functions.

• AM/FM tuning ........................................ see page 54

• Controlling a TV ..................................... see page 94

• Controlling other components ................. see page 95

• Controlling option components ............... see page 96

The operation mode of the remote control buttons in the shaded

area below depends on the operation mode selector position. Set

the operation mode selector to AMP to control this unit.

1 Infrared window

Outputs infrared control signals. Aim this window at the

component you want to operate (see page 9).

2 TRANSMIT indicator

Flashes while the remote control is sending infrared

signals.

3 Input selector buttons

Select the input source you want to control.

y

The selected input source name appears in the display window on

the remote control showing which source is currently operational.

4 Display window

Shows the name of the selected input source that you can

control.

5 LEVEL

Selects the speaker channel to be adjusted and sets the

output level (see page 51).

6 Cursor buttons k / n / l / h, ENTER

Select and adjust the sound field program parameters or

the “SET MENU” parameters.

7 RETURN

Returns to the previous menu level when adjusting the

“SET MENU” parameters.

8 Sound field program selector buttons

Select sound field programs (see page 44).

9 SUR. DECODE

Activates decoders to play back 2-channel sources in

surround (see page 73).

Remote control

V

-

AUX/DOCK

–

+

––

+

ENTER

DISPLAY

AUDIO

MENU

TITLE

TV MUTE

TV INPUT

MUTE

4

3

2

ENT

+

10

0

9

5

1

AV

TV

7

6

8

RETURN

ON

OFF

CLEAR

LEARN

RENAME

MACRO

REC

DISC SKIP

VOLUME

CH

TV VOL

EFFECT

PARAMETER

STRAIGHT

A/B/C/D/E

SRCH MODE

PURE DIRECT

PRESET/CH

SET MENU

B

A

ND

LEVEL

ENHANCER

STEREO

SUR. DECODE

SELECT

EXTD SUR.

CLASSICAL

LIVE/CLUB

ENTERTAIN

MOVIE

NIGHT

FREQ/TEXT

EON

MODE PTY SEEK

START

TV

SOURCE

AMP

SELECT

DTV

DVR/VCR 2

VCR 1

DVD

CBL/SAT

MD/TAPE

CD-R

PHONO

TUNER CD

MULTI CH IN

SLEEP

AUDIO SEL

POWER

STANDBY

1

2

3

4

5

6

7

8

9

0

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

U

t

S

R

Note

CONTROLS AND FUNCTIONS

7 En

INTRODUCTION

English

0 MACRO ON/OFF

Turns on or off the macro function (see page 100).

A MACRO

Programs a series of operations to be controlled with a

single button (see page 100).

B STANDBY

Sets the main zone to the standby mode (see page 31).

This button is operational only when MASTER ON/OFF on the

front panel is pressed inward to the ON position.

C POWER

Turns on the main zone (see page 31).

This button is operational only when MASTER ON/OFF on the

front panel is pressed inward to the ON position.

D AUDIO SEL

Toggles the priority for the type of audio input jack

between “AUTO”, “HDMI”, “COAX/OPT” and

“ANALOG” when one component is connected to two or

more input jacks (see page 40).

E SLEEP

Sets the sleep timer (see page 43).

F MULTI CH IN

Selects the component connected to the MULTI CH

INPUT jacks as the input source when using an external

decoder, etc. (see page 41).

G SELECT k / n

Selects another input source that you can control

independently of the input source selected with the input

selector buttons.

H Operation mode selector

Selects the operation mode of the remote control buttons

in the shaded area.

AMP

Operates the amplifier function of this unit.

SOURCE

Operates the component selected with an input

selector button (see page 95).

TV

Operates the TV assigned to either DTV or PHONO

(see page 94).

• To set the remote control codes for other components, see

page 96.

• When you set the remote control codes for both DTV and

PHONO (see page 96), priority is given to the one set for

DTV.

I VOLUME +/–

Increases or decreases the volume level.

J MUTE

Mutes the audio output. Press again to restore the audio

output to the previous volume level (see page 41).

K PURE DIRECT

Turns on or off the pure direct mode (see page 50).

L SET MENU

Enters “SET MENU” (see page 79).

M PARAMETER

Displays sound field parameter settings in the on-screen

display (OSD) (see page 69).

N STRAIGHT

Turns the sound field programs off or on. When the

“STRAIGHT” mode is selected, 2-channel or multi-

channel input signals are output directly from their

respective speakers without effect processing (see

page 49).

O EXTD SUR.

Switches between 5.1 and 6.1/7.1-channel playback of

multi-channel sources (see page 73).

P SELECT

Selects decoders for 2-channel sources (see pages 73 and

75).

Q ENHANCER

Turns on or off the Compressed Music Enhancer mode

(see page 52).

R NIGHT

Turns on or off the night listening modes (see page 53).

S RENAME

Changes the name of the input source in the display

window (see page 99).

T CLEAR

Clears remote control functions acquired from the learn,

macro and/or rename features (see page 103).

U LEARN

Programs remote control codes of functions from other

remote controls (see page 98).

Note

Notes

CONTROLS AND FUNCTIONS

8 En

This section describes the function of each control on the

Zone 2/Zone 3 remote control used to control the amplifier

functions of Zone 2 or Zone 3.

See the following pages for details about other controls

and functions.

• AM/FM tuning ........................................ see page 54

Zone 2/Zone 3 remote control is supplied with U.S.A., Canada,

Australia, U.K., China, Asia and General models only.

1 Input selector buttons

Select the desired input source of Zone 2 or Zone 3.

2 ID1/ID2 switch

Switches the remote control ID between ID1 and ID2

(see page 97).

3 POWER

Turns on Zone 2 or Zone 3.

This button is operational only when MASTER ON/OFF on the

front panel is pressed inward to the ON position.

4 STANDBY

Sets Zone 2 or Zone 3 to the standby mode.

This button is operational only when MASTER ON/OFF on the

front panel is pressed inward to the ON position.

5 VOLUME +/–

Increases or decreases the volume level of Zone 2 or

Zone 3.

6 MUTE

Mutes the sound of Zone 2 or Zone 3. Press again to

restore the audio output to the previous volume level.

7 ZONE 2/ZONE 3 switch

Switches between the operation mode of Zone 2 and that

of Zone 3.

Zone 2/Zone 3 remote control

Note

TUNER

CD

CD-R

DTV

PHONO

CBL/SAT

MD/TAPE

VCR 1

DVD

V-AUX/DOCK

DVR/VCR 2

POWER

STANDBY

A/B/C/D/E

PRESET

VOLUME

ZONE 3

ZONE 2

ID2

ID1

MUTE

2

7

6

5

4

3

1

Note

CONTROLS AND FUNCTIONS

9 En

INTRODUCTION

English

■ Installing batteries in the remote control

1 Press the part and slide the battery

compartment cover off.

2 Insert the four supplied batteries

(AAA, R03, UM-4) according to the polarity

markings (+ and –) on the inside of the

battery compartment.

3 Slide the cover back until it snaps into place.

■ Installing batteries in the Zone 2/Zone 3

remote control (Except Europe model)

1 Take off the battery compartment cover.

2 Insert the two supplied batteries (AAA, R03,

UM-4) according to the polarity markings

(+ and –) on the inside of the battery

compartment.

3 Snap the battery compartment cover back

into place.

• Change all of the batteries if you notice the following

conditions:

– the operation range of the remote control decreases.

– the TRANSMIT indicator does not flash or its light becomes

dim.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline and

manganese batteries) together. Read the packaging carefully as

these different types of batteries may have the same shape and

color.

• If the batteries have leaked, dispose of them immediately. Avoid

touching the leaked material or letting it come into contact with

clothing, etc. Clean the battery compartment thoroughly before

installing new batteries.

• Do not throw away batteries with general house waste; dispose

of them correctly in accordance with your local regulations.

• If the remote control is without batteries for more than 2

minutes, or if exhausted batteries remain in the remote control,

the contents of the memory may be cleared. When the memory

is cleared, insert new batteries, set up the remote control code

and program any acquired functions that may have been

cleared.

■ Using the remote control

The remote control transmits a directional infrared ray.

Be sure to aim the remote control directly at the remote

control sensor on this unit during operation.

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following types

of conditions:

– places of high humidity, such as near a bath

– places of high temperatures, such as near a heater or stove

– places of extremely low temperatures

– dusty places

Preparing the remote control

1

3

2

1

3

2

Notes

30 30

Approximately 6 m

Remote control sensor

CONTROLS AND FUNCTIONS

10 En

1 HDMI indicator

Lights up when the signal of the selected input source is

input at HDMI IN 1 or HDMI IN 2 jacks (see page 19).

2 DOCK indicator

Lights up when you station your iPod in a YAMAHA iPod

universal dock (such as the YDS-10, sold separately)

connected to the DOCK terminal of this unit

(see page 27).

3 Battery charge indicator

Lights up when this unit charges the battery of the

stationed iPod in the standby mode of this unit (see

page 66).

4 Input source indicators

The corresponding cursor lights up to show the currently

selected input source.

5 VOLUME level indicator

Indicates the current volume level.

6 MUTE indicator

Flashes while the MUTE function is on (see page 41).

7 Multi-information display

Shows the name of the current sound field program and

other information when adjusting or changing settings.

8 96/24 indicator

Lights up when a DTS 96/24 signal is input to this unit.

9 Input channel and speaker indicators

Input channel indicators

Indicate the channel components of the current digital

input signal.

Presence and surround back speaker

indicators

Light up according to the number of presence and

surround back speakers set for “PRESENCE SP” (see

page 82) and “SB L/R SP” (see page 82) in “SOUND

MENU” when “TEST” in “SOUND MENU” is set to

“ON” (see page 85).

y

You can make settings for the presence and surround back

speakers automatically by running “AUTO SETUP” (see

page 32) or manually by adjusting settings for “PRESENCE SP”

(see page 82) and “SB L/R SP” (see page 82) in “SOUND

MENU”.

Front panel display

CD-R

CD

PHONO

MULTI CH

TUNER

MD/TAPE

DVD

DTV

MUTE

VOLUME

dB

LFE

LL C R

SL SB SR

HiFi DSP

DIGITAL

EX

PL x

DSD

PCM

VIRTUAL

YPAO

ENHANCER

MATRIX

DISCRETE

CINEMA

SILENT

24

96

96/24

TUNED

STEREO

AUTO

MEMORY

PS

ZONE2

ZONE3

SLEEP

PTY HOLD

PTY

RT

CT

EON

NIGHT

DOCK

VCR 1

CBL/SAT

DVR/VCR 2

V-AUX

DSD

PCM

TUNED

STEREO

AUTO

MEMORY

PS

ZONE2

ZONE3

SLEEP

PTY HOLD

PTY

RT

CT

EON

NIGHT

HiFi DSP

DIGITAL

EX

PL x

VIRTUAL

YPAO

ENHANCER

MATRIX

DISCRETE

CINEMA

SILENT

24

96

J

I

H

G

F

E

C

B

A

0

O

N

M

L

K

9

87

654321

D

O........ U.K. and Europe models only

Presence speaker indicators

Input channel indicators

Surround back speaker indicators

L CR

SL SB SR

LFE

CONTROLS AND FUNCTIONS

11 En

INTRODUCTION

English

0 DSP indicators

The respective indicator lights up when any of the DSP

sound field programs are selected.

CINEMA DSP indicator

Lights up when you select a CINEMA DSP sound

field program (see page 45).

HiFi DSP indicator

Lights up when you select a HiFi DSP sound field

program (see page 45).

A VIRTUAL indicator

Lights up when Virtual CINEMA DSP is active (see

page 49).

B YPAO indicator

Lights up when you run “AUTO SETUP” and when the

speaker settings set in “AUTO SETUP” are used without

any modifications (see page 32).

C DSD indicator

Lights up when this unit is producing DSD (Direct Stream

Digital) digital audio signals.

D ENHANCER indicator

Lights up when the Compressed Music Enhancer mode is

turned on (see page 52).

E PCM indicator

Lights up when this unit is reproducing PCM (Pulse Code

Modulation) digital audio signals.

F Dolby decoder indicators

The respective indicator lights up when any of the Dolby

decoders of this unit function.

G Sound field indicators

Light up to indicate the active DSP sound fields.

H Headphones indicator

Lights up when headphones are connected (see page 41).

I SILENT CINEMA indicator

Lights up when headphones are connected and a sound

field program is selected (see page 49).

J DTS decoder indicators

The respective indicator lights up when any of the DTS

decoders of this unit function.

K Tuner indicators

Lights up when this unit is in the FM or AM tuning mode.

TUNED indicator

Lights up when this unit is tuned into a station

(see page 54).

STEREO indicator

Lights up when this unit is receiving a strong signal

for an FM stereo broadcast while the AUTO indicator

is lit (see page 54).

AUTO indicator

Lights up when this unit is in the automatic tuning

mode (see page 54).

MEMORY indicator

Flashes to show that a station can be stored

(see page 58).

L ZONE2/ZONE3 indicators

Lights up when Zone 2 or Zone 3 is turned on

(see page 107).

M NIGHT indicator

Lights up when you select a night listening mode

(see page 53).

N SLEEP indicator

Lights up while the sleep timer is on (see page 43).

O Radio Data System indicators

(U.K. and Europe models only)

PS, PTY, RT and CT

Light up according to the selected Radio Data System

display mode.

EON

Lights up when the EON data service is being

received.

PTY HOLD

Lights up while searching for the Radio Data System

stations in the PTY SEEK mode.

Presence DSP sound field

Listening position

Surround left

DSP sound field

Surround right

DSP sound field

Surround back DSP sound field

CONTROLS AND FUNCTIONS

12 En

1 REMOTE jacks

See page 106 for details.

2 COMPONENT VIDEO jacks

See pages 21 and 22 for connection information.

3 Audio component jacks

See page 24 for connection information.

4 Video component jacks

See pages 21 and 22 for connection information.

5 ANTENNA terminals

See page 28 for connection information.

6 WRENCH HOLDER

Use to hook the supplied speaker terminal wrench when

not in use (see page 15).

7 VOLTAGE SELECTOR

(Asia and General models only)

See page 29 for details.

8 AC IN/OUTLET(S)

See page 29 for connection information.

9 HDMI connectors

See page 19 for connection information.

0 DOCK terminal

See page 27 for connection information.

A DIGITAL INPUT/OUTPUT jacks

See page 22 for connection information.

B CONTROL OUT jack

This is a control expansion terminal for custom

installation.

C RS-232C terminal

This is a control expansion terminal for factory use only.

Consult your dealer for details.

D Speaker terminals

See page 14 for connection information.

E MULTI CH INPUT jacks

See page 26 for connection information.

F PRE OUT jacks

See page 25 for connection information.

G ZONE OUT jacks

See page 106 for connection information.

Rear panel

AC IN

AC OUTLETS

HOLDER

WRENCH

SPEAKERS

CENTER

BI-AMP

SURROUND BACK/

PRESENCE

SP1

FRONT

SURROUND

SINGLE

SP2

ANTENNA

FM

GND

AM

VIDEO

S VIDEO

MONITOR OUT

VIDEO

COMPONENT VIDEO

REMOTE

PHONO

GND

CD

IN

OUT

(REC)

(PLAY)

CD-R

HDMI

AUDIO

DOCK

DIGITAL INPUT

MULTI CH INPUT

PRE OUT

CONTROL OUT

RS-232C

DIGITAL OUTPUT

ZONE OUT

SUB

WOOFER

SUB

WOOFER

CENTER

FRONT(6CH)

FRONT

SURROUND

PRESENCE

SUR.BACK/

SINGLE(SB)

ZONE 2

ZONE 3

CD

D

VD

DVR/

VCR2

COAXIAL

1

2

CD

DVD

DTV

CBL/

SAT

MD/

TAP E

CD-R

98

7

6

5

4

32

1

SB(8CH)

DTV

TAP E

MD/

(REC)

(PLAY)

IN

OUT

DVD

DVR/VCR 2

VCR 1

CBL/SAT

OUT

IN

OUT

IN

DVD

DTV

CBL/SAT

MONITOR OUT

Y

P

R

P

R

P

B

P

B

IN

OUT

DVD

SAT

CBL/

IN 1

IN 2

OUT

+

A B

C

L

R

L

R

L

R

L

R

MULTI CH INPUT

PRE OUT

ZONE OUT

SUB

WOOFER

SUB

WOOFER

CENTER

FRONT(6CH)

FRONT

SURROUND

PRESENCE

SUR.BACK/

SINGLE(SB)

ZONE 2

ZONE 3

SB(8CH)

8765432

GFE

DCBA09

1

OPTICAL

CONNECTIONS

13 En

PREPARATION

English

The speaker layout below shows the speaker setting we

recommend. You can use it to enjoy CINEMA DSP and

multi-channel audio sources.

Front left and right speakers (FL and FR)

The front speakers are used for the main source sound plus

effect sounds. Place these speakers at an equal distance from

the ideal listening position. The distance of each speaker

from each side of the video monitor should be the same.

Center speaker (C)

The center speaker is for the center channel sounds

(dialog, vocals, etc.). If for some reason it is not practical

to use a center speaker, you can do without it. Best results,

however, are obtained with the full system. Place the

center speaker centrally between the front speakers and as

close to the monitor as possible, such as directly over or

under it.

Surround left and right speakers (SL and SR)

The surround speakers are used for effect and surround

sounds. Place these speakers behind your listening

position, facing slightly inwards, about 1.8 m above the

floor.

Surround back left and right speakers

(SBL and SBR)

The surround back speakers supplement the surround

speakers and provide more realistic front-to-back

transitions. Place these speakers directly behind the

listening position and at the same height as the surround

speakers. They should be positioned at least 30 cm apart.

Ideally, they should be positioned at the same width as that

of the front speakers.

Presence left and right speakers (PL and PR)

The presence speakers supplement the sound from the front

speakers with extra ambient effects produced by CINEMA

DSP (see page 126). These effects include sounds that

filmmakers intend to locate a little farther back behind the

screen in order to create more theater-like ambience. Place

these speakers at the front of the room about 0.5 to 1 m

outside the front speakers, facing slightly inward, and about

1.8 m above the floor.

Subwoofer (SW)

The use of a subwoofer with a built-in amplifier, such as

the YAMAHA Active Servo Processing Subwoofer

System, is effective not only for reinforcing bass

frequencies from any or all channels, but also for high

fidelity sound reproduction of the LFE (low-frequency

effect) channel included in Dolby Digital and DTS

sources. The position of the subwoofer is not so critical,

because low bass sounds are not highly directional. But it

is better to place the subwoofer near the front speakers.

Turn it slightly toward the center of the room to reduce

wall reflections.

CONNECTIONS

Placing speakers

SW

FR

PR

PL

FL

SBR

SBL

SL

SR

C

60˚

30˚

PL

PR

SBR

SBL

FL

FR

C

SL

SR

80˚

SL

FR

PRPL

C

FL

1.8 m

30 cm or more

1.8 m

0.5 to 1 m 0.5 to 1 m

14 En

CONNECTIONS

Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are faulty,

no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be

unnatural and lack bass.

• Before connecting the speakers, make sure that this unit is turned off (see page 31).

• Do not let the bare speaker wires touch each other or do not let them touch any metal part of this

unit. This could damage this unit and/or speakers.

• Use magnetically shielded speakers. If this type of speaker still creates interference with the

monitor, place the speakers away from the monitor.

• If you are to use 6 ohm speakers, be sure to set “SP IMP.” to “6ΩMIN” before using this unit (see

page 30). 4 ohm speakers can be also used as the front speakers (see page 111).

• A speaker cord is actually a pair of insulated cables running side by side. Cables are colored or shaped differently, perhaps with a

stripe, groove or ridge. Connect the striped (grooved, etc.) cable to the “+” (red) terminals of this unit and your speaker. Connect the

plain cable to the “–” (black) terminals.

• The low-frequency signals of other speakers set to “SML” (or “SMALL”) or to “NONE” in “SPEAKER SET” (see pages 80 and 82)

are directed to the speakers selected in “LFE/BASS OUT” (see page 80).

• You can connect both surround back and presence speakers to this unit, however they do not output sound simultaneously. You can set

to prioritize either set of speakers using the “PRIORITY” parameter in “MANUAL SETUP” (see page 82).

• You can use the PRESENCE terminals to connect the Zone 2 or Zone 3 speakers as well as the presence speakers (see page 106).

Connecting speakers

Notes

CAUTION

SPEAKERS

CENTER

BI-AMP

SURROUND BACK/

PRESENCE

SP1

FRONT

SURROUND

SINGLE

SP2

PRE OUT

SUB

WOOFER

+

L

R

L

R

Front speakers

Surround speakers

Presence speakers

Subwoofer

Right

Left

Center speaker

Surround back speakers

Right

Left

Right

Zone 2 or Zone 3

speakers

(see page 106)

15 En

CONNECTIONS

PREPARATION

English

FRONT terminals

Connect front left and right speakers to these terminals.

CENTER terminals

Connect a center speaker to these terminals.

SURROUND terminals

Connect surround left and right speakers to these

terminals.

SURROUND BACK terminals

Connect surround back left and right speakers to these

terminals.

When you use a surround back speaker, connect the speaker to the

left SURROUND BACK terminal (SINGLE).

PRESENCE terminals

Connect presence left and right speakers to these

terminals.

SUBWOOFER jack

Connect a subwoofer with a built-in amplifier (such as the

YAMAHA Active Servo Processing Subwoofer System)

to this jack.

■ Connecting the speaker cable

1 Remove approximately 10 mm of insulation

from the end of each speaker cable and then

twist the exposed wires of the cable together

to prevent short circuits.

2 Loosen the knob using the supplied speaker

terminal wrench.

3 Insert one bare wire into the hole on the side

of each terminal.

4 Tighten the knob to secure the wire using the

supplied speaker terminal wrench.

Note

10 mm

Speaker terminal wrench

Red: positive (+)

Black: negative (–)

16 En

CONNECTIONS

5 Hook the speaker terminal wrench onto the

WRENCH HOLDER on the rear panel of this

unit when not in use.

■ Connecting to the SP2 speaker

terminals

Connect Zone 2 or Zone 3 speakers to these terminals (see

page 106).

1 Open the tab.

2 Insert one bare wire into the hole on the

terminal.

3 Close the tab to secure the wire.

■ Connecting the banana plug

(except U.K., Europe, Asia and Korea

models)

The banana plug is a single-pole electrical connector

widely used to terminate speaker cables.

1 Tighten the knob using the supplied speaker

terminal wrench.

2 Insert the banana plug connector into the

end of the corresponding terminal.

y

You can also use the banana plug with the SP2 speaker terminals.

Open the tab and then insert one banana plug into the hole on the

terminal. Do not close the tab after connecting the banana plug.

Red: positive (+)

Black: negative (–)

Banana plug

Red: positive (+)

Black: negative (–)

Speaker terminal wrench

17 En

CONNECTIONS

PREPARATION

English

Some of the speakers have speaker wire connections that

allow bi-amplification to enhance the performance of the

speaker system. This unit allows you to make bi-

amplification connection to one speaker system. Check if

your speakers support bi-amplification. As these speakers

are shipped to you, you will note shorting bars or bridges,

one connecting the two red input terminals and the other

connecting the two black input terminals. Remove these

shorting bars or bridges only if you plan to bi-amplify

your speakers.

■ Conventional connection

If you want to connect your speakers as traditional

loudspeakers using the conventional connection method,

connect your speakers using the regular left and right

speaker wire connections and ignore the second set of

terminals.

■ Bi-amplification connection

To make the bi-amplification connections, use the FRONT

and SURROUND BACK terminals as shown below. To

activate the bi-amplification connections, set “BI-AMP”

to “ON” in “ADVANCED SETUP” (see page 112).

Remove the shorting bars or bridges to separate the LPF (low

pass filter) and HPF (high pass filter) crossovers.

Using bi-amplification connections

FRONT

+ +

R

L

This unit

Shorting bars

or bridges

Shorting bars

or bridges

Front speakers

Right Left

Note

BI-AMP

SURROUND BACK/

FRONT

SINGLE

+

R

L

+

This unit

Front speakers

Left

Right

18 En

CONNECTIONS

■ Audio jacks

This unit has three types of audio jacks. Connection

depends on the availability of audio jacks on your other

components.

AUDIO jacks

For conventional analog audio signals transmitted via left

and right analog audio cables. Connect red plugs to the

right jacks and white plugs to the left jacks.

DIGITAL COAXIAL jacks

For digital audio signals transmitted via coaxial digital

audio cables.

DIGITAL OPTICAL jacks

For digital audio signals transmitted via optical digital

audio cables.

You can use the digital jacks to input PCM, Dolby Digital and

DTS bitstreams. When you connect components to both the

COAXIAL and OPTICAL jacks, priority is given to the signals

input at the COAXIAL jack. All digital input jacks are

compatible with 96-kHz sampling digital signals.

■ Video jacks

This unit has three types of video jacks. Connection

depends on the availability of input jacks on your video

monitor.

VIDEO jacks

For conventional composite video signals transmitted via

composite video cables.

S VIDEO jacks

For S-video signals, separated into the luminance (Y) and

chrominance (C) video signals transmitted on separate

wires of S-video cables.

COMPONENT VIDEO jacks

For component video signals, separated into the

luminance (Y) and chrominance (P

B, PR) video signals

transmitted on separate wires of component video cables.

y

This unit equips the video connection function. See pages 20 and

90 for details.

Information on jacks and cable plugs

VIDEO S VIDEO

COMPONENT VIDEO

Y R PB P

PB

Y

P

R

S

V

COAXIAL

DIGITAL

AUDIO

OPTICAL

DIGITAL

R

L

C

O

R

L

Left and right

analog audio

cable plugs

Optical

digital

audio cable

plug

Coaxial

digital audio

cable plug

Composite

video cable

plug

S-video

cable plug

Component

video cable

plugs

Audio jacks and cable plugs Video jacks and cable plugs

(Red)(White) (Orange) (Yellow) (Green) (Blue) (Red)

Note

La pagina si sta caricando...

Yamaha RX-V1700 Manuale del proprietario

Yamaha RX-V1700 Manuale del proprietario

in altre lingue

Documenti correlati