Yamaha HTR-5840 Manuale del proprietario

HTR-5840

AV Receiver

Ampli-tuner audio-vidéo

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

GEBRUIKSAANWIJZING

ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ

G

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

1 To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

2 Install this sound system in a well ventilated, cool,

dry, clean place – away from direct sunlight, heat

sources, vibration, dust, moisture, and/or cold.

Allow ventilation space of at least 30 cm on the top,

20 cm on the left and right, and 20 cm on the back of

this unit.

3 Locate this unit away from other electrical

appliances, motors, or transformers to avoid

humming sounds.

4 Do not expose this unit to sudden temperature

changes from cold to hot, and do not locate this unit

in a environment with high humidity (i.e. a room with

a humidifier) to prevent condensation inside this

unit, which may cause an electrical shock, fire,

damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign object may

fall onto this unit and/or this unit may be exposed to

liquid dripping or splashing. On the top of this unit,

do not place:

– Other components, as they may cause damage

and/or discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause

fire, damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall

and liquid may cause electrical shock to the user

and/or damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to obstruct heat radiation. If

the temperature inside this unit rises, it may cause

fire, damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may

overheat, possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cord from the wall

outlet, grasp the plug; do not pull the cord.

11 Do not clean this unit with chemical solvents; this

might damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used.

Using this unit with a higher voltage than specified

is dangerous and may cause fire, damage to this

unit, and/or personal injury. YAMAHA will not be

held responsible for any damage resulting from use

of this unit with a voltage other than specified.

13 To prevent damage by lightning, disconnect the

power cord from the wall outlet during an electrical

storm.

14 Do not attempt to modify or fix this unit. Contact

qualified YAMAHA service personnel when any

service is needed. The cabinet should never be

opened for any reasons.

15 When not planning to use this unit for long periods

of time (i.e. vacation), disconnect the AC power plug

from the wall outlet.

16 Be sure to read the “TROUBLESHOOTING” section

on common operating errors before concluding that

this unit is faulty.

17 Before moving this unit, press STANDBY/ON to set

this unit in the standby mode, and disconnect the

AC power plug from the wall outlet.

■ For U.K. customers

If the socket outlets in the home are not suitable for the

plug supplied with this appliance, it should be cut off and

an appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

The plug severed from the mains lead must be destroyed, as a

plug with bared flexible cord is hazardous if engaged in a live

socket outlet.

■ Special Instructions for U.K. Model

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

WAR NING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN

OR MOISTURE.

This unit is not disconnected from the AC power

source as long as it is connected to the wall outlet, even

if this unit itself is turned off. This state is called the

standby mode. In this state, this unit is designed to

consume a very small quantity of power.

Note

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured

markings identifying the terminals in your plug,

proceed as follows:

The wire which is coloured BLUE must be connected

to the terminal which is marked with the letter N or

coloured BLACK. The wire which is coloured

BROWN must be connected to the terminal which is

marked with the letter L or coloured RED.

Making sure that neither core is connected to the earth

terminal of the three pin plug.

1

PREPARATIONINTRODUCTION

BASIC

OPERATION

SOUND FIELD

PROGRAMS

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

English

FEATURES............................................................. 2

GETTING STARTED............................................ 3

Supplied accessories .................................................. 3

Installing batteries in the remote control ................... 3

CONTROLS AND FUNCTIONS ......................... 4

Front panel................................................................. 4

Remote control........................................................... 6

Using the remote control ........................................... 7

Front panel display .................................................... 8

Rear panel ................................................................ 10

SPEAKER SETUP ............................................... 11

Speaker placement................................................... 11

Speaker connections ................................................ 12

CONNECTIONS .................................................. 14

Before connecting components................................ 14

Connecting video components................................. 15

Connecting audio components................................. 18

Connecting the FM and AM antennas ..................... 19

Connecting the power supply cord .......................... 20

Speaker impedance setting ...................................... 21

Turning on the power............................................... 21

BASIC SETUP ...................................................... 22

Using the BASIC SETUP menu .............................. 22

PLAYBACK.......................................................... 25

Basic operations....................................................... 25

Selecting sound field programs ............................... 27

Selecting input modes.............................................. 31

FM/AM TUNING ................................................. 33

Automatic and manual tuning.................................. 33

Presetting stations.................................................... 34

Selecting preset stations........................................... 36

Exchanging preset stations ...................................... 37

Receiving Radio Data System stations.................... 38

Changing the Radio Data System mode ..................39

PTY SEEK function ................................................ 40

EON function........................................................... 41

RECORDING ....................................................... 42

SOUND FIELD PROGRAM

DESCRIPTIONS...............................................43

For movie/video sources.......................................... 43

For music sources .................................................... 45

ADVANCED OPERATIONS ..............................46

Using the sleep timer ............................................... 46

Manually adjusting speaker levels........................... 47

SET MENU............................................................48

Using SET MENU................................................... 49

1 SOUND MENU.................................................... 50

2 INPUT MENU...................................................... 52

3 OPTION MENU................................................... 53

ADVANCED SETUP MENU...............................55

REMOTE CONTROL FEATURES ...................57

Control area ............................................................. 57

Setting remote control codes ................................... 58

Controlling other components ................................. 59

EDITING SOUND FIELD PARAMETERS ......60

What is a sound field ............................................... 60

Changing parameter settings ................................... 60

SOUND FIELD PARAMETER

DESCRIPTIONS...............................................62

TROUBLESHOOTING .......................................64

RESETTING THE FACTORY PRESETS ........68

GLOSSARY...........................................................69

Audio formats .......................................................... 69

Sound field programs............................................... 70

Audio information ................................................... 70

Video signal information ......................................... 71

SPECIFICATIONS...............................................72

CONTENTS

INTRODUCTION

PREPARATION

BASIC OPERATION

SOUND FIELD PROGRAMS

ADVANCED OPERATION

ADDITIONAL INFORMATION

FEATURES

2

Built-in 6-channel power amplifier

◆ Minimum RMS output power

(0.06% THD, 20 Hz to 20 kHz, 8 !)

Front: 85 W + 85 W

Center: 85 W

Surround: 85 W + 85 W

Surround back: 85 W

Sound field features

◆ Proprietary YAMAHA technology for the creation of

sound fields

◆ Dolby Digital/Dolby Digital EX decoder

◆ DTS/DTS-ES Matrix 6.1, Discrete 6.1, DTS Neo:6,

DTS 96/24 decoder

◆ Dolby Pro Logic/Dolby Pro Logic II/

Dolby Pro Logic IIx decoder

◆ Virtual CINEMA DSP

◆ SILENT CINEMA

™

Sophisticated AM/FM tuner

◆ 40-station random and direct preset tuning

◆ Automatic preset tuning

◆ Preset station shifting capability (preset editing)

Other features

◆ 192-kHz/24-bit D/A converter

◆ A SET MENU that provides you with items for

optimizing this unit for your audio/video system

◆ 6 additional input jacks for discrete multi-channel input

◆ S-video signal input/output capability

◆ Component video input/output capability

◆ Optical and coaxial digital audio signal jacks

◆ Sleep timer

◆ Cinema and music night listening modes

◆ Remote control with preset remote control codes

• y indicates a tip for your operation.

• Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button

names differ between the main unit and the remote control, the button name on the remote control is given in parentheses.

• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In

case of differences between the manual and product, the product has priority.

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, “Surround EX”, and the double-D symbol

are trademarks of Dolby Laboratories.

“SILENT CINEMA” is a trademark of YAMAHA

CORPORATION.

“DTS”, “DTS-ES”, “Neo:6” and “DTS 96/24” are trademarks of

Digital Theater Systems, Inc.

FEATURES

GETTING STARTED

3

INTRODUCTION

English

Please check that you received all of the following parts.

1 Press the part and slide the battery

compartment cover off.

2 Insert two supplied batteries (AA, R06,

UM-3) according to the polarity markings

(+ / –) on the inside of the battery

compartment.

3 Slide the cover back until it snaps into place.

Notes on batteries

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline and

manganese batteries) together. Read the packaging carefully as

these different types of batteries may have the same shape and

color.

• If the batteries have leaked, dispose of them immediately. Avoid

touching the leaked material or letting it come into contact with

clothing, etc. Clean the battery compartment thoroughly before

installing new batteries.

• Do not throw away batteries with general house waste; dispose

of them correctly in accordance with your local regulations.

GETTING STARTED

Supplied accessories

CODE SET

STANDBY

SYSTEM

POWER

CD

MD/CD-R

TUNER

V-AUXDVD

AMP

POWER POWER

REC

AUDIO

MUTE

MENUTITLE

VOLUME

DISC SKIP

FREQ/TEXT EON

START

SET MENU

LEVEL

A/B/C/D/E

MODE PTY SEEK

PRESET/CH

STRAIGHT

MOVIEENTERTAINMUSIC

STEREO

4321

8

10

7

09

65

ENT.

DIRECT ST.EXTD SUR.STANDARD

SELECT

NIGHT

B

SPEAKERS

A

DISPLAYRETURN

TV MUTE TV INPUT

TV VOL TV CH

AVTV

ENTER

VCR

DTV/CBL

MULTI CH IN

SLEEP

Remote control

Batteries (2)

(AA, R06, UM-3)

AM loop antenna

75-ohm/300-ohm antenna

adapter (U.K. model only)

Indoor FM antenna

Installing batteries in the remote

control

1

3

2

If the remote control is without batteries for more than

2 minutes, or if exhausted batteries remain in the

remote control, the contents of the memory may be

cleared. When the memory is cleared, insert new

batteries, set up the remote control code and program

any acquired functions that may have been cleared.

CONTROLS AND FUNCTIONS

4

1 STANDBY/ON

Turns on this unit or sets it to the standby mode. When you

turn on this unit, you will hear a click and there will be a 4

to 5-second delay before this unit can reproduce sound.

In standby mode, this unit consumes a small amount of power in

order to receive infrared-signals from the remote control.

2 Remote control sensor

Receives signals from the remote control.

3 Front panel display

Shows information about the operational status of this unit.

4 FM/AM

Switches the reception band when the unit is in tuner

mode.

5 A/B/C/D/E, NEXT

Selects one of the 5 preset station groups (A to E) when

the unit is in tuner mode.

Selects the speaker channel to be adjusted when the unit is

not in tuner mode.

6 PRESET/TUNING l / h, LEVEL –/+

Selects preset station number 1 to 8 when the colon (:) is

displayed next to the band indication in the front panel

display when the unit is in tuner mode. Selects the tuning

frequency when the colon (:) is not displayed.

Adjusts the level of the speaker channel selected using

A/B/C/D/E (NEXT) when the unit is not in tuner mode.

7 MEMORY (MAN’L/AUTO FM)

Stores a station in the memory. Hold down this button for

more than 3 seconds to start automatic preset tuning.

8 TUNING MODE (AUTO/MAN’L MONO)

Switches between automatic tuning (AUTO indicator on)

and manual tuning (AUTO indicator off).

9 VIDEO AUX jacks

Input audio and video signals from a portable external

source such as a game console. To reproduce source

signals from these jacks, select V-AUX as the input source.

0 VOLUME

Controls the output level of all audio channels.

This does not affect the REC OUT level.

CONTROLS AND FUNCTIONS

Front panel

VOLUME

AUTO/MAN'L MONO

VIDEO L AUDIO R

MAN'L/AUTO FMLEVELNEXTEDIT

EFFECT

MEMORY

FM/AMPRESET/TUNING

A/B/C/D/E

l PROGRAM h

BASS/TREBLE

l PRESET/TUNING h

TUNING MODE

INPUT MODE

TONE CONTROL

STRAIGHT

SPEAKERSPHONES

SILENT CINEMA

STANDBY

/ON

BA

MULTI CH

INPUT

VIDEO AUX

INPUT

21347 856 09

JHGEBACDFI

FREQ/TEXT EON

MODE

PTY SEEK

START

LMNK

Note

CONTROLS AND FUNCTIONS

5

INTRODUCTION

English

A PHONES (SILENT CINEMA) jack

Outputs audio signals for private listening with

headphones. When you connect headphones, no signals

are output to the OUTPUT jacks or to the speakers.

All Dolby Digital and DTS audio signals are mixed down

to the left and right headphone channels.

B SPEAKERS A/B

Turns on or off the set of front speakers connected to the A

and/or B terminals on the rear panel each time the

corresponding button is pressed.

C PRESET/TUNING (EDIT)

Switches the function of PRESET/TUNING l / h

(LEVEL –/+) between selecting preset station numbers

and tuning.

D STRAIGHT (EFFECT)

Switches the sound fields off or on. When STRAIGHT is

selected, input signals (2-channel or multi-channel) are

output directly from their respective speakers without

effect processing.

E TONE CONTROL

Use to adjust the bass/treble balance for the front left and

right speakers (see page 26).

F BASS/TREBLE –/+

Use to adjust the bass/treble balance for the front left and

right speakers (in conjunction with CONTROL).

G PROGRAM l / h

Use to select sound field programs (see page 26).

H INPUT MODE

Sets the priority (AUTO, DTS, ANALOG) for the type of

signals received when one component is connected to two

or more of this unit’s input jacks (see page 31).

I INPUT selector

Selects the input source you want to listen to or watch.

J MULTI CH INPUT

Selects the source connected to the MULTI CH INPUT

jacks. When selected, the MULTI CH INPUT source takes

priority over the source selected with INPUT (or the input

selector buttons on the remote control).

■ Radio Data System tuning buttons

K FREQ/TEXT

Press this button when the unit is receiving a Radio Data

System station to cycle the display between the PS mode,

PTY mode, RT mode, CT mode (if the station offers those

Radio Data System data services) and/or the frequency

display (see page 39).

L PTY SEEK MODE

Press this button to set the unit to the PTY SEEK mode

(see page 40).

M PTY SEEK START

Press this button to begin searching for a station after the

desired program type has been selected in the PTY SEEK

mode (see page 40).

N EON

Press this button to select a radio program type (NEWS,

INFO, AFFAIRS, SPORT) to tune in automatically (see

page 41).

CONTROLS AND FUNCTIONS

6

This section describes the function of each control on the

remote control used to control this unit. To operate other

components, see “REMOTE CONTROL FEATURES” on

page 57.

1 Infrared window

Outputs infrared control signals. Aim this window at the

component you want to operate.

2 Input selector buttons

Select the input source and change the control area.

3 Sound field program/numeric buttons

Use to select sound field programs.

Use numbers 1 through 8 to select preset stations when the

unit is in tuner mode.

Use SELECT to playback 2-channel sources in surround

(see page 29).

Use EXTD SUR. to switch between 5.1 or 6.1-channel

playback of multi-channel software (see page 28).

Use DIRECT ST. to playback 2-channel sources in high

fidelity sound (see page 30).

4 SPEAKERS A/B

Use to turn on or off the set of front speakers connected to

the A and/or B terminals on the rear panel each time the

corresponding button is pressed.

5 LEVEL

Selects the speaker channel to be adjusted and sets the

level.

6 Cursor buttons u / d / j / i / ENTER

Use to select and adjust sound field program parameters or

SET MENU items.

Press i to select a preset station group (A to E) when the

unit is in tuner mode.

Press u / d to select a preset station number (1 to 8)

when the unit is in tuner mode.

7 RETURN

Returns to the previous menu level when adjusting the

SET MENU parameters.

8 STANDBY

Sets this unit in the standby mode.

9 SYSTEM POWER

Turns on the power of this unit.

0 SLEEP

Sets the sleep timer.

A MULTI CH IN

Selects multi-channel input when using an external

decoder (etc.).

B CODE SET

Use to set up remote control codes (see page 58).

C AMP

Selects the AMP mode. You must select the AMP mode to

control the main unit.

Remote control

CODE SET

STANDBY

SYSTEM

POWER

CD

MD/CD-R

TUNER

V-AUXDVD

AMP

POWER POWER

REC

AUDIO

MUTE

MENUTITLE

VOLUME

DISC SKIP

FREQ/TEXT EON

START

SET MENU

LEVEL

A/B/C/D/E

MODE PTY SEEK

PRESET/CH

STRAIGHT

MOVIEENTERTAINMUSIC

STEREO

4321

8

10

7

09

65

ENT.

DIRECT ST.EXTD SUR.STANDARD

SELECT

NIGHT

B

SPEAKERS

A

DISPLAYRETURN

TV MUTE TV INPUT

TV VOL TV CH

AVTV

ENTER

VCR

DTV/CBL

MULTI CH IN

SLEEP

8

9

0

A

B

C

D

E

F

H

1

2

3

4

6

5

7

G

I

CONTROLS AND FUNCTIONS

7

INTRODUCTION

English

D VOLUME +/–

Increases or decreases the volume level.

E MUTE

Mutes the sound. Press again to restore the audio output to

the previous volume level.

F STRAIGHT

Switches the sound fields off or on. When STRAIGHT is

selected, input signals (2-channel or multi-channel) are

output directly from their respective speakers without

effect processing.

G NIGHT

Turns on or off the night listening modes (see page 30).

H SET MENU

Activates the SET MENU function.

I Radio Data System tuning buttons

FREQ/TEXT

Press this button when the unit is receiving a Radio Data

System station to cycle the display between the PS mode,

PTY mode, RT mode, CT mode (if the station offers those

Radio Data System data services) and/or the frequency

display (see page 39).

PTY SEEK MODE

Press this button to set the unit to the PTY SEEK mode

(see page 40).

PTY SEEK START

Press this button to begin searching for a station after the

desired program type has been selected in the PTY SEEK

mode (see page 40).

EON

Press this button to select a radio program type (NEWS,

INFO, AFFAIRS, SPORT) to tune in automatically (see

page 41).

The remote control transmits a directional infrared beam.

Be sure to aim the remote control directly at the remote

control sensor on the main unit during operation.

■ Handling the remote control

• Do not spill water or other liquids on the remote

control.

• Do not drop the remote control.

• Do not leave or store the remote control in the

following types of conditions:

– places of high humidity, such as near a bath

– high temperature, such as near a heater or stove

– extremely low temperatures

– dusty places

Using the remote control

VOLUME

AUTO/MAN'L MONO

VIDEO L AUDIO R

MAN'L/AUTO FMLEVELNEXTEDIT

EFFECT

MEMORY

FM/AMPRESET/TUNING

A/B/C/D/E

l PROGRAM h

BASS/TREBLE

TUNING MODE

INPUT MODE

TONE CONTROL

STRAIGHT

SPEAKERSPHONES

SILENT CINEMA

STANDBY

/ON

BA

MULTI CH

INPUT

VIDEO AUX

INPUT

30 30

CODE SET

STANDBY

SYSTEM

POWER

CD

MD/CD-R

TUNER

V-AUXDVD

AMP

POWER POWER

REC

AUDIO

MUTE

MENUTITLE

VOLUME

DISC SKIP

FREQ/TEXT EON

START

SET MENU

LEVEL

A/B/C/D/E

MODE PTY SEEK

PRESET/CH

STRAIGHT

MOVIEENTERTAINMUSIC

STEREO

4321

8

10

7

09

65

ENT.

DIRECT ST.EXTD SUR.STANDARD

SELECT

NIGHT

B

SPEAKERS

A

DISPLAYRETURN

TV MUTE TV INPUT

TV VOL TV CH

AVTV

ENTER

VCR

DTV/CBL

MULTI CH IN

SLEEP

CATEGORY

EDIT

l PRESET/TUNING h

Approximately 6 m

CONTROLS AND FUNCTIONS

8

1 Decoder indicators

When any of this unit’s decoders function, the respective

indicator lights up.

2 VIRTUAL indicator

Lights up when Virtual CINEMA DSP is active (see

page 31).

3 SILENT CINEMA indicator

Lights up when headphones are connected and a sound

field program is selected (see page 26).

4 Input source indicators

A cursor lights to show the current input source.

5 Sound field indicators

Light to indicate the active DSP sound fields.

6 CINEMA DSP indicator

Lights up when you select a CINEMA DSP sound field

program.

7 AUTO indicator

Lights up to indicate that automatic tuning is possible.

8 TUNED indicator

Lights up when this unit is tuned into a station.

9 STEREO indicator

Lights up when this unit is receiving a strong signal for an

FM stereo broadcast while the AUTO indicator is lit.

0 MEMORY indicator

Flashes to show that a station can be stored.

A MUTE indicator

Flashes while the MUTE function is on.

B VOLUME level indication

Indicates the current volume level.

C PCM indicator

Lights up when this unit is reproducing PCM (Pulse Code

Modulation) digital audio signals.

D STANDARD indicator

Lights up when Surround Standard or Surround Enhanced

is selected (see page 29).

E NIGHT indicator

Lights up when you select night listening mode.

F SP A B indicators

Light up according to the set of front speakers selected.

Both indicators light up when both sets of speakers are

selected.

G Headphones indicator

Lights up when headphones are connected.

H HiFi DSP indicator

Lights up when you select a HiFi DSP sound field

program.

I Multi-information display

Shows the current sound field program name and other

information when adjusting or changing settings.

Front panel display

CDTUNER

MD/CD-R

DVD

DTV/CBL

V-A UX

VCR

96

24

q

PL

q

EX

q

PL

MATRIX DISCRETE

SILENT CINEMA

NIGHT

ZONE2

STANDARD

HD AUTO

YPAO

PS

HOLD

RT CT

EON

PTY

XM

TUNED STEREO MUTE

VOLUME

MEMORY

SLEEP

VIRTUAL

PCM

q

PL x

A B

SP

mS

dB

ft

dB

96/24

HiFi DSP

LFE

DUAL

LCR

SL SB SR

q

DIGITAL

t

PS

HOLD

RT CT EONPTY

PTY

12 3456780AB9

EG HI M

KNLDC

F

J

Presence DSP sound field

Listening position

Left surround

DSP sound field

Right surround

DSP sound field

Surround back DSP sound field

CONTROLS AND FUNCTIONS

9

INTRODUCTION

English

J Radio Data System indicators

The name(s) of the Radio Data System data offered by the

currently received Radio Data System station light(s) up.

EON lights up when an Radio Data System station that

offers the EON data service is being received.

PTY HOLD lights up while searching for stations in the

PTY SEEK mode.

K SLEEP indicator

Lights up while the sleep timer is on.

L 96/24 indicator

Lights up when a DTS 96/24 signal is input to this unit.

M LFE indicator

Lights up when the input signal contains the LFE signal.

N Input channel indicators/speaker indicators

Indicate the channel components of the current digital

input signal.

Indicate the number of speakers connected in SPEAKERS

(page 23), or indicate the channel being adjusted in SP

LEVEL (page 51).

CONTROLS AND FUNCTIONS

10

1 DIGITAL INPUT jacks

See pages 15, 17 and 18 for details.

2 MULTI CH INPUT jacks

See page 16 for connection information.

3 Video component jacks

See pages 15 and 17 for connection information.

4 AC OUTLET(S)

Use to supply power to your other A/V components (see

page 20).

5 Audio component jacks

See page 18 for connection information.

6 SUBWOOFER OUTPUT jack

See page 13 for connection information.

7 Antenna terminals

See page 19 for connection information.

8 Speaker terminals

See page 13 for connection information.

Rear panel

SPEAKERS

FRONT

CENTER

SURROUND

BACK

R

L

CENTER

SUB

WOOFER

MONITOR OUT

MULTI CH INPUT

OUTPUT

AUDIO

VIDEO

DVD

DTV/

CBL

VIDEO

R

L

R

L

IN

(

PLAY

)

OUT

(

REC

)

MD/

CD-R

CD

OUT

VCR

VIDEO

IN

FRONT

SURROUND

TUNER

AM

ANT

GND

COMPONENT VIDEO

P

R

DVD

MONITOR

OUT

DTV/

CBL

P

B

Y

DIGITAL

INPUT

DVD

DTV/CBL

CD

COAXIAL

+

–

+

–

+

––

+++

+

–

A

B

FM

ANT

OPTICAL

SUB

WOOFER

R

L

AC OUTLETS

SWITCHED

75Ω UNBAL.

S VIDEO

XM/DT

12 3 4

5 67 8

SPEAKER SETUP

11

PREPARATION

English

The speaker layout below shows the standard ITU-R

*

speaker setting. You can use it to enjoy CINEMA DSP and

multi-channel audio sources.

*

ITU-R is the radio communication sector of the ITU

(International Telecommunication Union).

Front speakers (FR and FL)

The front speakers are used for the main source sound plus

effect sounds. Place these speakers an equal distance from

the ideal listening position. The distance of each speaker

from each side of the video monitor should be the same.

Center speaker (C)

The center speaker is for the center channel sounds

(dialog, vocals, etc.). If for some reason it is not practical

to use a center speaker, you can do without it. Best results,

however, are obtained with the full system. Align the front

face of the center speaker with the front face of your video

monitor. Place the speaker centrally between the front

speakers and as close to the monitor as possible, such as

directly over or under it.

Surround speakers (SR and SL)

The surround speakers are used for effect and surround

sounds. Place these speakers behind your listening

position, facing slightly inwards, about 1.8 m (6 ft) above

the floor.

Surround back speaker (SB)

The surround back speaker supplements the surround

speakers and provides for more realistic front-to-back

transitions. Place this speaker directly behind the listening

position and at the same height as the surround speakers.

Subwoofer

The use of a subwoofer, such as the YAMAHA Active

Servo Processing Subwoofer System, is effective not only

for reinforcing bass frequencies from any or all channels,

but also for high fidelity reproduction of the LFE (low-

frequency effect) channel included in Dolby Digital and

DTS software. The position of the subwoofer is not so

critical, because low bass sounds are not highly

directional. But it is better to place the subwoofer near the

front speakers. Turn it slightly toward the center of the

room to reduce wall reflections.

SPEAKER SETUP

Speaker placement

60˚

30˚

SB

FL

FR

C

SL

SR

80˚

SL

1.8 m

12

SPEAKER SETUP

Be sure to connect the left channel (L), right channel (R),

“+” (red) and “–” (black) properly. If the connections are

faulty, no sound will be heard from the speakers, and if the

polarity of the speaker connections is incorrect, the sound

will be unnatural and lack bass.

• If you will use 4 or 6 ohm speakers, be sure to

set this unit’s speaker impedance setting to 4

ohms before using (see page 21).

• Before connecting the speakers, make sure that the

power of this unit is off.

• Do not let the bare speaker wires touch each other or do

not let them touch any metal part of this unit. This

could damage this unit and/or speakers.

• Use magnetically shielded speakers. If this type of

speakers still creates the interference with the monitor,

place the speakers away from the monitor.

A speaker cord is actually a pair of insulated cables

running side by side. One cable is colored or shaped

differently, perhaps with a stripe, groove or ridges.

Connect the striped (grooved, etc.) cable to the “+” (red)

terminals on this unit and your speaker. Connect the plain

cable to the “–” (black) terminals.

1 Remove approximately 10 mm of insulation

from the end of each speaker cable.

2 Twist the exposed wires of the cable together

to prevent short circuits.

3 Unscrew the knob.

4 Insert one bare wire into the hole in the side

of each terminal.

5 Tighten the knob to secure the wire.

Speaker connections

CAUTION

10 mm

1

2

Red: positive (+)

Black: negative (–)

3

4

5

13

SPEAKER SETUP

PREPARATION

English

■ FRONT terminals

Connect one or two speaker systems (2, 3) to these

terminals. If you use only one speaker system, connect it

to the FRONT A or B terminals.

■ CENTER terminals

Connect a center speaker (4) to these terminals.

■ SURROUND terminals

Connect surround speakers (6, 7) to these terminals.

■ SUBWOOFER jack

Connect a subwoofer with built-in amplifier (1), such as

the YAMAHA Active Servo Processing Subwoofer

System, to this jack.

■ SURROUND BACK terminals

Connect a surround back speaker (5) to these terminals.

SPEAKERS

FRONT

CENTER

SURROUND

BACK

R

L

OUTPUT

+

–

+

–

+

––

+++

+

–

A

B

SUB

WOOFER

2 3 6 71

54

Subwoofer

system

Center

speaker

Front speakers (A)

Surround back

speaker

LeftRight

Surround speakers

Front

speakers

(B)

1

2

3

4

5

7

6

Speaker layout

CONNECTIONS

14

Do not connect this unit or other components to the main

power until all connections between components are

complete.

■ Cable indications

■ Analog jacks

You can input analog signals from audio components by

connecting audio pin cable to the analog jacks on this unit.

Connect red plugs to the right jacks and white plugs to the

left jacks.

■ Digital jacks

This unit has digital jacks for direct transmission of digital

signals through either coaxial or fiber optic cables. You

can use the digital jacks to input PCM, Dolby Digital and

DTS bitstreams. When you connect components to both

the COAXIAL and OPTICAL jacks, priority is given to

the input signals from the COAXIAL jack. All digital

input jacks are compatible with 96-kHz sampling digital

signals.

This unit handles digital and analog signals independently. Thus

audio signals input to the analog jacks are only output to the

analog OUT (REC) jacks.

Dust protection cap

Pull out the cap from the optical jack before you connect

the fiber optic cable. Do not discard the cap. When you are

not using the optical jack, be sure to put the cap back in

place. This cap protects the jack from dust.

■ Video jacks

This unit has three types of video jacks. Connection

depends on the availability of input jacks on your monitor.

VIDEO jacks

For conventional composite video signals.

S VIDEO jacks

For S-video signals, separated into luminance (Y) and

color (C) video signals to achieve high-quality color

reproduction.

COMPONENT VIDEO jacks

For component signals, separated into luminance (Y) and

color difference (P

B, PR) to provide the best quality in

picture reproduction.

CONNECTIONS

Before connecting components

Note

CAUTION

S

V

O

L

R

C

Y

P

B

PR

left analog cables

right analog cables

optical cables

coaxial cables

video cables

For analog signals

For digital signals

For video signals

S-video cables

component video cables

VIDEO

S VIDEO

COMPONENT VIDEO

P

R

P

B

Y

S VIDEO

VIDEO

COMPONENT

VIDEO

Signal flow inside this unit

Output

(MONITOR OUT)

Input

15

CONNECTIONS

PREPARATION

English

■ Connections for DVD playback

Be sure to connect your video source components in the same way you connect your video monitor to this unit. For example, if you

connect your video monitor to this unit using a VIDEO connection, connect your video source components to this unit using the VIDEO

connections.

Connecting video components

Note

MONITOR OUT

AUDIO

VIDEO

DVD

VIDEO

R

L

VIDEO

COMPONENT VIDEO

PR

DVD

MONITOR

OUT

PB

Y

DIGITAL

INPUT

DVD

OPTICAL

S VIDEO

LR

O

S

P

R PB Y

V

DVD player

Video

monitor

Optical out

Video out

Audio out

Video in

16

CONNECTIONS

■ Connecting to the MULTI CH INPUT jacks

This unit is equipped with 6 additional input jacks (left and right FRONT, CENTER, left and right SURROUND and

SUBWOOFER) for discrete multi-channel input from a multi-format player, external decoder, sound processor or pre-

amplifier.

Connect the output jacks on your multi-format player or external decoder to the MULTI CH INPUT jacks. Be sure to

match the left and right outputs to the left and right input jacks for the front and surround channels.

• When you select MULTI CH INPUT as the input source, this unit automatically turns off the digital sound field processor, and you

cannot select sound field programs.

• This unit does not redirect signals input to the MULTI CH INPUT jacks to accommodate for missing speakers. We recommend that

you connect at least a 5.1-channel speaker system before using this feature.

• When headphones are used, only front left and right channels are output.

Notes

CENTER

SUB

WOOFER

MULTI CH INPUT

FRONT

SURROUND

R

L

LRLR

Multi-format player/

External decoder

Front

out

Surround

out

Subwoofer

out

Center

out

17

CONNECTIONS

PREPARATION

English

■ Connections for other video components

• Be sure to connect your video source components in the same way you connect your video monitor to this unit. For example, if you

connect your video monitor to this unit using a VIDEO connection, connect your video source components to this unit using the

VIDEO connection.

• When recording, you must make the same type of video connections (i.e., S-video) between each component.

■ VIDEO AUX jacks (on the front panel)

Use these jacks to connect any video source, such as a

game console or video camera, to this unit.

Notes

MONITOR OUT

AUDIO

VIDEO

DTV/

CBL

VIDEO

R

L

OUT

VCR

VIDEO

IN

COMPONENT VIDEO

PR

MONITOR

OUT

DTV/

CBL

PB

Y

DIGITAL

INPUT

DTV/CBL

OPTICAL

S VIDEO

O

LR

LR LR

V

S

P

R PB Y

S

V

S

V

Cable TV or

satellite tuner

DVD recorder

or VCR

Audio out

Video outOptical out

Audio out

Video out

Video in

Audio in

Video in

Video

monitor

VIDEO L AUDIO R

VIDEO AUX

V

L

R

Game

console or

video camera

Video out

Audio out L

Audio out R

18

CONNECTIONS

■ Connections for audio components

Connecting audio components

R

L

IN

(

PLAY

)

OUT

(

REC

)

MD/

CD-R

CD

COAXIAL

L

R

LR

C

CD player

MD recorder or

tape deck

Coaxial out

Audio out

Audio in

Audio out

La pagina si sta caricando...

Yamaha HTR-5840 Manuale del proprietario

Yamaha HTR-5840 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti