Dometic SINEPOWER DSP 1524 Istruzioni per l'uso

DSP612, DSP624, DSP1012, DSP1024,

DSP1512, DSP1524, DSP2012, DSP2024

Sine wave inverter

Installation and Operating Manual. . . . . . . . 3

Sinus-Wechselrichter

Montage- und Bedienungsanleitung . . . . . 21

Onduleur sinusoïdal

Instructions de montage

et de service . . . . . . . . . . . . . . . . . . . . . . . . .40

Convertidor de ondas seno

Instrucciones de montaje y de uso . . . . . . .60

Conversor sinusoidal

Instruções de montagem e manual de

instruções . . . . . . . . . . . . . . . . . . . . . . . . . . .80

Inverter sinusoidale

Istruzioni di montaggio e d’uso . . . . . . . . 100

Sinus ondulator

Montagehandleiding en

gebruiksaanwijzing . . . . . . . . . . . . . . . . . .120

Sinus ensretter

Monterings- og betjeningsvejledning. . . 139

Sinus växelriktare

Monterings- och bruksanvisning . . . . . . . 157

Sinus vekselretter

Monterings- og bruksanvisning. . . . . . . . 175

Sinus -vaihtosuuntaaja

Asennus- ja käyttöohje . . . . . . . . . . . . . . . 193

Синусоидальный инвертор

Инструкция по монтажу и эксплуатации 211

Przetwornica sinusoidalna

Instrukcja montażu i obsługi. . . . . . . . . . . 232

Sínusový menič napätia

Návod na montáž a uvedenie

do prevádzky. . . . . . . . . . . . . . . . . . . . . . . 252

Sinusový měnič

Návod k montáži a obsluze . . . . . . . . . . . 270

Szinuszos inverter

Szerelési és használati útmutató . . . . . . . 288

EN

DE

FR

ES

PT

IT

NL

DA

SV

NO

FI

RU

PL

SK

CS

HU

ENERGY & LIGHTING

SINEPOWER

DSP600-2000--IO-16s.book Seite 1 Montag, 7. Mai 2018 1:39 13

DSP600-2000--IO-16s.book Seite 2 Montag, 7. Mai 2018 1:39 13

EN

SinePower

3

Please read this instruction manual carefully before installation and first

use, and store it in a safe place. If you pass on the product to another

person, hand over this instruction manual along with it.

Table of contents

1 Explanation of symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

2 General safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

3 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

4 Target group for this manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

5 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

6 Technical description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

7 Fitting the inverter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

8 Connecting the inverter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

9 Using the inverter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

10 Cleaning and caring for the inverter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

11 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

12 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

13 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

14 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

DSP600-2000--IO-16s.book Seite 3 Montag, 7. Mai 2018 1:39 13

EN

Explanation of symbols SinePower

4

1 Explanation of symbols

D

!

A

I

2 General safety instructions

2.1 General safety

The manufacturer accepts no liability for damage in the following cases:

• Faulty assembly or connection

• Damage to the product resulting from mechanical influences and incorrect

connection voltage

• Alterations to the product without express permission from the manufacturer

• Use for purposes other than those described in the operating manual

Note the following basic safety information when using electrical devices to protect

against:

• Electric shock

•Fire hazards

•Injury

DANGER!

Safety instruction: Failure to observe this instruction will cause fatal or

serious injury.

WARNING!

Safety instruction: Failure to observe this instruction can cause fatal or

serious injury.

NOTICE!

Failure to observe this instruction can cause material damage and impair

the function of the product.

NOTE

Supplementary information for operating the product.

DSP600-2000--IO-16s.book Seite 4 Montag, 7. Mai 2018 1:39 13

EN

SinePower General safety instructions

5

2.2 General safety

D

DANGER!

• In the event of fire, use a fire extinguisher which is suitable for electrical

devices.

!

WARNING!

• Only use the device as intended.

• Ensure that the red and black terminals never come into contact.

• Disconnect the device from the power supply:

– Before cleaning and maintenance

– Before changing a fuse

• If you disassemble the device:

– Detach all connections

– Make sure that no voltage is present at any of the inputs and out-

puts

• The device may not be used if the device itself or the connection cable

are visibly damaged.

• If this power cable for this device is damaged, it must be replaced by

the manufacturer, customer service or a similarly qualified person in

order to prevent safety hazards.

• This device may only be repaired by qualified personnel. Inadequate

repairs may cause serious hazards.

• This device can be used by children aged 8 years or over, as well as by

persons with diminished physical, sensory or mental capacities or a

lack of experience and/or knowledge, providing they are supervised

or have been taught how to use the device safely and are aware of the

resulting risks.

• Electrical devices are not toys.

Always keep and use the appliance out of the reach of children.

• Children must be supervised to ensure that they do not play with the

device.

A

NOTICE!

• Before start-up, check that the voltage specification on the type plate

is the same as that of the power supply.

• Ensure that other objects cannot cause a short circuit at the contacts

of the device.

• Never pull the plug out of the socket by the connection cable.

DSP600-2000--IO-16s.book Seite 5 Montag, 7. Mai 2018 1:39 13

EN

General safety instructions SinePower

6

• Store the device in a dry and cool place.

2.3 Safety when installing the device

D

DANGER!

• Never mount the device anywhere where there is a risk of gas or dust

explosion.

!

CAUTION!

• Ensure that the device is standing firmly.

The device must be set up and fastened in such a way that it cannot tip

over or fall down.

A

NOTICE!

• Do not expose the device to a heat source (such as direct sunlight or

heating). Avoid additional heating of the device in this way.

• Set up the device in a dry location where it is protected against splash-

ing water.

2.4 Safety when connecting the device electronically

D

DANGER! Danger of electrocution

• If you are working on electrical systems, ensure that there is somebody

close at hand who can help you in emergencies.

!

WARNING!

• Make sure that the lead has a sufficient cross-section.

• Lay the cables so that they cannot be damaged by the doors or the

bonnet.

Crushed cables can lead to serious injury.

!

CAUTION!

• Lay the cables so that they cannot be tripped over or damaged.

A

NOTICE!

• Use ductwork or cable ducts if it is necessary to lay cables through

metal panels or other panels with sharp edges.

•Do not lay the 230 V mains cable and the 12 V DC cable in the same

duct.

•Do not lay the cable so that it is loose or heavily kinked.

DSP600-2000--IO-16s.book Seite 6 Montag, 7. Mai 2018 1:39 13

EN

SinePower Scope of delivery

7

• Fasten the cables securely.

• Do not pull on the cables.

2.5 Operating the device safely

D

DANGER! Danger of electrocution

• Do not touch exposed cables with your bare hands.

!

WARNING!

• Only use the device in closed, well-ventilated rooms.

!

CAUTION!

•Do not operate the device

– In salty, wet or damp environments

– In the vicinity of corrosive fumes

– In the vicinity of combustible materials

– In areas where there is a danger of explosions.

• Before starting the device, ensure that the power supply line and the

plug are dry.

• Always disconnect the power supply when working on the device.

• Please observe that parts of the device may still conduct voltage even

if the fuse has blown.

• Do not disconnect any cables when the device is still in use.

A

NOTICE!

• Make sure the air inlets and outlets of the device are not covered.

• Ensure good ventilation.

3Scope of delivery

No. in

fig. 1

Designation

1 Sine wave inverter

2 Remote control

3 Connection cable remote control

– Operating manual

DSP600-2000--IO-16s.book Seite 7 Montag, 7. Mai 2018 1:39 13

EN

Target group for this manual SinePower

8

4 Target group for this manual

The electrical installation (chapter “Connecting the inverter” on page 12) is intended

for professionals who are familiar with the applicable regulations of the country in

which the equipment is to be installed and/or used.

All other chapters are intended for the users.

5 Intended use

!

The wave inverter converts direct current into a 230 V AC supply of 50 Hz:

• 12 Vg: DSP612, DSP1012, DSP1512, DSP2012

• 24 Vg: DSP624, DSP1024, DSP1524, DSP2024

6 Technical description

The inverters can be operated wherever a DC connection is available:

• 12 Vg: DSP612, DSP1012, DSP1512, DSP2012

• 24 Vg: DSP624, DSP1024, DSP1524, DSP2024

The light-weight and compact construction of this device allows for easy installation

in mobile homes, commercial vehicles or motor and sailing yachts.

The output voltage corresponds to the household voltage from the socket (pure sine

wave, THD <5 %).

Please observe the values for constant output power and peak output power as

indicated in chapter “Technical data” on page 18. Never connect devices that have

a higher power requirement.

I

WARNING!

Never use the inverter on vehicles where the positive terminal of the

battery is connected to the chassis.

NOTE

Note when connecting devices with an electrical drive (such as power

drills and refrigerators), that they often require more power than is

indicated on the type plate.

DSP600-2000--IO-16s.book Seite 8 Montag, 7. Mai 2018 1:39 13

EN

SinePower Technical description

9

The inverter has various protective mechanisms.

• Overvoltage shutdown: The inverter shuts itself off when the voltage exceeds

the cut-off value. It restarts when the voltage returns to the restart value.

• Undervoltage shutdown: The inverter shuts itself off when the voltage sinks

below the cut-off value. It restarts when the voltage rises to the restart value.

• Excess temperature shutdown: The inverter switches off when the tempera-

ture inside the device or the temperature on the cooling element exceeds a cut-

off value. It restarts when the voltage rises to the restart value.

• Overloading and short circuit shutdown: The LED on the inverter indicates

an operating fault when an excess load is connected or a short circuit has

occurred.

I

The inverter can be operated in the following net configurations:

• TN network:

The neutral conductor of the inverter is grounded. A downstream safety switch

(RCD) must be installed.

• IT network:

Both phases are insulated. This is suitable for operating one load. If more than

one load will be connected a protection plan has to be set up (e. g. insulation

monitor).

The net configuration is set via a DIP switch at the inverter.

The inverter can be switched with the remote control to an energy-saving mode to

prevent the connected battery from discharging too quickly.

Using the remote control, the inverter can be turned on or off and switched to the

energy-saving mode.

6.1 Control elements

NOTE

The individual values are found in the chapter “Technical data” on

page 18.

No. in

fig. 2

Description Description

1 Main switch Switches the device on or off

2 Status LED See chapter “Status indications” on page 14

3 Dip switch Sets the net configuration

DSP600-2000--IO-16s.book Seite 9 Montag, 7. Mai 2018 1:39 13

EN

Fitting the inverter SinePower

10

6.2 Connections

I

6.3 Remote control

7 Fitting the inverter

7.1 Tools required

For the electrical connection you will need the following tools:

•Crimping tool

• 3multi-coloured, flexible connection cables. Determine the necessary thickness

from the table in chapter “Connecting the inverter” on page 12.

• Cable lugs and conductor sleeves

For fastening you will require the following tools:

• Machine bolts (M4) with washers and self-locking nuts or

• self-tapping screws or wood screws

NOTE

The version for continental Europe is depicted.

No. in

fig. 2

Description

4 AC outlet

5 Remote control connection

6 DC connection

7 Ground terminal (Earthing on the vehicle bodywork)

8Fan

No. in

fig. 3

Description

1 On/off button

2 Status LED

3 Terminal for remote control

DSP600-2000--IO-16s.book Seite 10 Montag, 7. Mai 2018 1:39 13

EN

SinePower Fitting the inverter

11

7.2 Mounting instructions

When selecting the installation location, observe the following instructions:

• The inverter can be mounted horizontally or vertically.

• The inverter must be installed in a place that is protected from moisture.

• The inverter may not be installed in the presence of flammable materials.

• The inverter may not be installed in a dusty environment.

• The place of installation must be well ventilated. A ventilation system must be

available for installations in small, enclosed spaces. The minimum clearance

around the inverter must be at least 5 cm (fig. 4).

• The air intake on the back or the air outlet on the front of the inverter must remain

clear.

• For ambient temperatures higher than 40 °C (such as in engine or heating

compartments, or direct sunlight), the inverter may shut down although the

connected load is below the rated load (derating).

• The device must be installed on a level and sufficiently sturdy surface.

A

7.3 Mounting the inverter

➤ Mount the inverter as shown (fig. 5).

7.4 Mounting the remote control

➤ Mount the remote control as shown (fig. 6).

➤ Remove the protective film.

NOTICE!

Before drilling any holes, make sure that no electrical cables or other

parts of the vehicle can be damaged by drilling, sawing and filing.

DSP600-2000--IO-16s.book Seite 11 Montag, 7. Mai 2018 1:39 13

EN

Connecting the inverter SinePower

12

8 Connecting the inverter

8.1 General instructions

!

• When installed in vehicles or boats, the inverter must be connected to the chassis

or earth.

• When setting up a socket distribution circuit (mains setup), comply with the

applicable regulations.

• Only use copper cables.

• Keep the DC cables as short as possible (< 1 m).

• Keep to the specified cable cross section and fit a cable fuse (fig. 7 1) as close

to the battery as possible on the positive cable (see the table).

WARNING!

• The inverter may only be connected by a qualified workshop. The

following information is intended for technicians who are familiar

with the guidelines and safety precautions to be applied.

• Never use the inverter on vehicles where the positive terminal of the

battery is connected to the chassis.

• If you do not fit a fuse to the positive cable, the cables can over-

load, which might result in a fire.

Device

Required cable

cross section

Cable fuse

DSP612 25 mm² 150 A

DSP624 25 mm² 150 A

DSP1012 35 mm² 200 A

DSP1024 25 mm² 150 A

DSP1512 50 mm² 250 A

DSP1524 25 mm² 150 A

DSP2012 70 mm² 300 A

DSP2024 35 mm² 200 A

DSP600-2000--IO-16s.book Seite 12 Montag, 7. Mai 2018 1:39 13

EN

SinePower Connecting the inverter

13

8.2 Connecting the inverter

A

I

➤ Connect the inverter as shown:

– Connecting the battery: fig. 7

– Connecting the ground terminal fig. 8

– Connecting the 230 V output cable: fig. 9

8.3 Connecting the remote control

A

➤ Connect the remote control as shown(fig. 0).

8.4 Connecting external switch (accessories)

I

➤ Close an external switch as shown (fig. a).

NOTICE!

• Make sure that you do not reverse the polarity. Incorrect polarity can

damage the inverter.

• Make sure that the inverter is operated with the following voltage

only:

– DSP612, DSP1012, DSP1512, DSP2012: 12 Vg

– DSP624, DSP1024, DSP1524, DSP2024: 24 Vg

NOTE

Tighten the nuts and bolts to a maximum torque of 15 Nm. Loose

connections may cause overheating.

NOTICE!

Only plug in the connection to the remote control in the remote port.

The device can be damaged by connecting it incorrectly.

NOTE

When using an external switch, you cannot change the status of energy

saving mode.

DSP600-2000--IO-16s.book Seite 13 Montag, 7. Mai 2018 1:39 13

EN

Using the inverter SinePower

14

9Using the inverter

9.1 Switching on the inverter

➤ Set the main switch (fig. 2 1) of the inverter as follows.

– “0”: Inverter completely switched off

– “I”: Standard operation

– “II”: Operation via remote control

✓ The inverter performs a self-test.

✓ After the self-test is completed successfully, the status LED (fig. 2 2) indicates

the operation mode:

– Constantly lit: Normal mode activated

– Flashes four times: Energy-saving mode activated

9.2 Status indications

The LED (fig. 2 2) shows the operating condition of the inverter.

The inverter switches off if:

• The battery voltage drops below 10 V (12 Vg connection) or

20 V (24 Vg connection).

• The battery voltage exceeds 16 V (12 Vg connection) or

32 V (24 Vg connection).

• The inverter is overloaded.

• The inverter overheats.

In case of shutdown due to overvoltage or undervoltage the inverter restarts when

the set voltage value is reached.

In case of shutdown due to overload or overheating proceed as follows:

➤ Shut down the inverter with the main switch (fig. 2 1).

Display Input voltage

Constantly lit Normal mode

Long flash, short interruption Inverter overheated/Overload

Quick flash Overvoltage/Undervoltage

Off Other fault

DSP600-2000--IO-16s.book Seite 14 Montag, 7. Mai 2018 1:39 13

EN

SinePower Using the inverter

15

➤ Check that the inverter is sufficiently ventilated and that the ventilation grilles are

unimpeded.

➤ Wait 5 – 10 minutes and switch the inverter on again without any electric

consumers.

9.3 Switching to energy-saving mode

I

Activating energy saving mode

➤ If necessary, switch the inverter off.

➤ Press the on/off button (fig. 3 1) of the remote control until the status LED

(fig. 3 2) of the remote control has flashed six times.

✓ Then the status LED (fig. 3 2) of the remote control flashes every 5 seconds.

✓ Energy saving mode is activated.

Deactivating energy saving mode

➤ Switch the inverter off.

➤ Press the on/off button (fig. 3 1) of the remote control until the status LED

(fig. 3 2) of the remote control goes on constantly.

Before the status LED goes on constantly, it indicates that energy saving mode

will be switched off by an interval of flashing four times followed by flashing six

times.

✓ Normal mode is activated.

NOTE

• The inverter automatically switches to normal operation when a load

over 45 W is connected.

• If an external switch is connected, you cannot change the energy

saving mode.

DSP600-2000--IO-16s.book Seite 15 Montag, 7. Mai 2018 1:39 13

EN

Cleaning and caring for the inverter SinePower

16

9.4 Configuring the net configuration

D

Using the dip switch you can define in which net configuration the inverter shall

operate.

10 Cleaning and caring for the inverter

A

➤ Occasionally clean the product with a damp cloth.

DANGER!

Changing the net configuration results in risk of lethal injury.

The dip switch must only be set by qualified personnel.

Remove the the dip switch‘s protection cap for configuring only. Insert

the protection cap to prevent switching the dip switch‘s setting.

Parameter Dip switch

TN grid

An external downstream circuit breaker (RCD) is

necessary.

On

IT grid

Operation with one load only or installation of an

external insulation monitor.

National standards shall apply!

Off

NOTICE!

Do not use sharp or hard objects or cleaning agents for cleaning as these

may damage the product.

DSP600-2000--IO-16s.book Seite 16 Montag, 7. Mai 2018 1:39 13

EN

SinePower Troubleshooting

17

11 Troubleshooting

!

I

The LED (fig. 2 2) indicates the fault:

WARNING!

Do not open the device. You risk sustaining an electric shock by doing

this.

NOTE

If you have detailed questions on the specifications of the inverter

please contact the manufacturer (addresses on the back of the instruc-

tion manual).

LED display Cause Remedy

Quick flash Input voltage is

too high

Check the input voltage and reduce it.

Input voltage too

low

The battery needs recharging.

Check the cables and connections.

2 s lit, short

interruption

Overheating Switch off the inverter and the consumer.

Wait 5 to 10 minutes and switch the inverter on again

without any electric consumers.

Reduce the load and make sure the inverter has better

ventilation. Then switch the consumer back on.

Excessive load Switch off the inverter and remove the consumer.

Then switch the inverter back on without the con-

sumer. If no excessive load is now shown, then there

is a short circuit in the consumer or the total load was

higher than the power specified on the data sheet.

Check the cables and connections.

Off Other fault Contact the service.

DSP600-2000--IO-16s.book Seite 17 Montag, 7. Mai 2018 1:39 13

EN

Warranty SinePower

18

12 Warranty

The statutory warranty period applies. If the product is defective, please contact the

manufacturer's branch in your country (see the back of the instruction manual for the

addresses) or your retailer.

For repair and guarantee processing, please include the following documents when

you send in the device:

• A copy of the receipt with purchasing date

• A reason for the claim or description of the fault

13 Disposal

➤ Place the packaging material in the appropriate recycling waste bins wherever

possible.

M

If you wish to finally dispose of the product, ask your local recycling centre

or specialist dealer for details about how to do this in accordance with the

applicable disposal regulations.

14 Technical data

The following technical data applies to all inverters:

Output voltage: 230 Vw ± 10 %, pure sine wave (THD <5 %)

Output frequency: 50 Hz ± 0,5 Hz

Efficiency: >90 %

Heat dissipation: temperature and load controlled fan

Ambient temperature at operation: 0 °C to +50 °C

Ambient temperature for storage: –30 °C to +70 °C

Air humidity: 0 – 95 %, non-condensing

Testing/certification:

9

DSP600-2000--IO-16s.book Seite 18 Montag, 7. Mai 2018 1:39 13

EN

SinePower Technical data

19

DSP612 DSP 1012 DSP624 DSP 1024

Ref. no.: 9600002543

9600003597

9600002545

9600003599

9600002544

9600003598

9600002546

9600003600

Rated input voltage: 12 V g 24 V g

Input voltage range: 10 – 16.5 Vg 20 – 33 Vg

Rated load: 600 W 1000 W 600 W 1000 W

Maximum power for 1 min: 690 W 1150 W 690 W 1150 W

Surge power for 1 s: 1200 W 2000 W 1200 W 2000 W

Idle current consumption at

rated voltage:

<0.8 A <1.0 A <0.5 A <0.6 A

Standby current

consumption:

<0.3 A <0.35 A <0.2 A <0.2 A

Dimensions W x L x H: fig. e

Weight: 2.8 kg 3.1 kg 2.8 kg 3.1 kg

DSP1512 DSP 2012 DSP1524 DSP 2024

Ref. no.: 9600002547

9600003601

9600002549

9600003603

9600002561

9600002548

9600003602

9600002550

9600003604

9600002562

Rated input voltage: 12 V g 24 V g

Input voltage range: 10 – 16.5 Vg 20 – 33 Vg

Rated load: 1500 W 2000 W 1500 W 2000 W

Maximum power for 1 min: 1725 W 2300 W 1725 W 2300 W

Surge power for 1 s: 3000 W 4000 W 3000 W 4000 W

Idle current consumption at

rated voltage:

<1.2 A <1.5 A <0.6 A <0.8 A

Standby current

consumption:

<0.4 A <0.5 A <0.25 A <0.3 A

Dimensions W x L x H: fig. e

Weight: 4.9 kg 5.2 kg 4.9 kg 5.2 kg

DSP600-2000--IO-16s.book Seite 19 Montag, 7. Mai 2018 1:39 13

EN

Technical data SinePower

20

Protective devices

Overvoltage shutdown

Undervoltage shutdown

For the current EU declaration of conformity for your device please refer to the

respective product page on dometic.com or contact the manufacturer directly (see

back page).

12 V 24 V

Input: Undervoltage, reverse polarity (internal fuse)

AC output: Overvoltage, short circuit, overload

Temperature: Shutdown

Short circuit protection: Yes, Ipk

Device

Overvoltage

Shutdown Restart

DSP612, DSP1012, DSP1512, DSP2012 16.5 V 15.5 V

DSP624, DSP1024, DSP1524, DSP2024 33 V 31 V

Device

Undervoltage

Shutdown Restart

DSP612, DSP1012, DSP1512, DSP2012 10 V 12 V

DSP624, DSP1024, DSP1524, DSP2024 20 V 24 V

DSP600-2000--IO-16s.book Seite 20 Montag, 7. Mai 2018 1:39 13

La pagina sta caricando ...

Dometic SINEPOWER DSP 1524 Istruzioni per l'uso

Dometic SINEPOWER DSP 1524 Istruzioni per l'uso

in altre lingue

Documenti correlati

Altri documenti