Dometic CAM60ADR Istruzioni per l'uso

Tipo
Istruzioni per l'uso

Questo manuale è adatto anche per

CAM60ADR
Rear View Video Camera
Installation and Operating Manual . . . . . . 9
Rückfahrvideokamera
Montage- und Bedienungsanleitung . . . 20
Caméra vidéo de recul
Instructions de montage
et de service . . . . . . . . . . . . . . . . . . . . . . . 31
Cámara de vídeo de marcha atrás
Instrucciones de montaje y de uso . . . . .42
Câmara de marcha-atrás
Instruções de montagem e manual de
instruções . . . . . . . . . . . . . . . . . . . . . . . . . 53
Videocamera per la retromarcia
Istruzioni di montaggio e d’uso . . . . . . . . 64
Achteruitrijvideocamera
Montagehandleiding en
gebruiksaanwijzing. . . . . . . . . . . . . . . . . . 75
Bakvideokamera
Monterings- og betjeningsvejledning. . . 86
Backningsvideokamera
Monterings- och bruksanvisning . . . . . . . 97
Ryggevideokamera
Monterings- og bruksanvisning . . . . . . . 108
Peruutusvideokamera
Asennus- ja käyttöohje. . . . . . . . . . . . . . 120
Видеокамера заднего вида
Инструкция по монтажу
и эксплуатации. . . . . . . . . . . . . . . . . . . . .131
Kamera cofania
Instrukcja montażu i obsługi . . . . . . . . . 142
Cúvacia kamera
Návod na montáž a uvedenie
do prevádzky . . . . . . . . . . . . . . . . . . . . . 153
Couvací kamera
Návod k montáži a obsluze . . . . . . . . . . 164
Tol a t ó kam e r a
Szerelési és használati útmutató . . . . . . 176
EN
DE
FR
ES
PT
IT
NL
DA
SV
NO
FI
RU
PL
SK
CS
HU
DRIVING SUPPORT
PERFECTVIEW
CAM60ADR-IO-16s.book Seite 1 Donnerstag, 7. Juli 2016 1:21 13
CAM60ADR-IO-16s.book Seite 2 Donnerstag, 7. Juli 2016 1:21 13
CAM60ADR
3
1 2 3
4
9
6
8
5
7
10 11
12
1
CAM60ADR-IO-16s.book Seite 3 Donnerstag, 7. Juli 2016 1:21 13
CAM60ADR
4
2
3
4
5
CAM60ADR-IO-16s.book Seite 4 Donnerstag, 7. Juli 2016 1:21 13
CAM60ADR
5
1
2
3
Ø 16 mm
6
3
1
2
7
CAM60ADR-IO-16s.book Seite 5 Donnerstag, 7. Juli 2016 1:21 13
CAM60ADR
6
90°
8
9
0
a
b
c
CAM60ADR-IO-16s.book Seite 6 Donnerstag, 7. Juli 2016 1:21 13
CAM60ADR
7
d
~50°
e
f
A
B
g
CAM60ADR-IO-16s.book Seite 7 Donnerstag, 7. Juli 2016 1:21 13
CAM60ADR
8
h
CAM60ADR-IO-16s.book Seite 8 Donnerstag, 7. Juli 2016 1:21 13
CAM60ADR Explanation of symbols
EN
9
Please read this instruction manual carefully before installation and first use, and store
it in a safe place. If you pass on the product to another person, hand over this instruc-
tion manual along with it.
Contents
1 Explanation of symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2 Safety and installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
6 Technical description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7 Information on the electrical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
8 Mounting the camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
9 Cleaning and caring for the camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
10 Guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
11 Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
12 Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
1 Explanation of symbols
!
!
A
I
WARNING!
Safety instruction: Failure to observe this instruction can cause fatal or serious injury.
CAUTION!
Safety instruction: Failure to observe this instruction can lead to injury.
NOTICE!
Failure to observe this instruction can cause material damage and impair the function
of the product.
NOTE
Supplementary information for operating the product.
CAM60ADR-IO-16s.book Seite 9 Donnerstag, 7. Juli 2016 1:21 13
Safety and installation instructions CAM60ADR
EN
10
2 Safety and installation instructions
The manufacturer accepts no liability for damage in the following cases:
Faulty assembly or connection
Damage to the product resulting from mechanical influences and excess voltage
Alterations to the product without express permission from the manufacturer
Use for purposes other than those described in the operating manual
Please observe the prescribed safety instructions and stipulations from the vehicle
manufacturer and service workshops.
!
WARNING!
Inadequate supply cable connections could result in short circuits, which could have as
a consequence that:
Cable fires occur
The airbag is triggered
Electronic control devices are damaged
Electric functions fail (indicators, brake light, horn, ignition, lights)
A
NOTICE!
To prevent the risk of short circuits, always disconnect the negative terminal of the vehi-
cle's electrical system before working on it.
If the vehicle has an additional battery, its negative terminal should also be discon-
nected.
Please observe the following instructions:
When working on the following cables, only use insulated cable lugs, plugs and flat push-on
receptacles:
30 (direct supply from positive battery terminal)
–15 (connected positive terminal, behind the battery)
31 (return line from the battery, earth)
L (indicator lights left)
R (indicator lights right)
Do not use terminal strips.
Use a crimping tool to connect the cables.
When connecting to cable 31 (earth), screw the cable
to the vehicle's earth bolt with a cable lug and a gear disc or
to the sheet-metal bodywork with a cable lug and a self-tapping screw.
Ensure that there is a good earth connection.
CAM60ADR-IO-16s.book Seite 10 Donnerstag, 7. Juli 2016 1:21 13
CAM60ADR Safety and installation instructions
EN
11
If you disconnect the negative terminal of the battery, all data stored in the volatile memories will
be lost.
The following data must be set again, depending on the vehicle equipment options:
–Radio code
Vehicle clock
–Timer
On-board computer
Seat position
You can find instructions for making these settings in the appropriate operating instructions.
Observe the following installation instructions:
!
CAUTION!
Secure the parts installed in the vehicle in such a way that they cannot become loose
under any circumstances (sudden braking, accidents) and cause injuries to the
occupants of the vehicle.
Secure any parts of the system covered by the bodywork in such a manner that they
cannot be come loose or damage other parts and cables or impair vehicle functions
(steering, pedals, etc).
Always follow the safety instructions of the vehicle manufacturer.
Some work (e.g. on retention systems such as the AIRBAG etc.) may only be per-
formed by qualified specialists.
A
NOTICE!
To prevent damage when drilling, make sure there is sufficient space on the other
side for the drill head to come out.
Deburr all drill holes and treat them with a rust-protection agent.
Observe the following instructions when working with electrical parts:
A
NOTICE!
When testing the voltage in electrical cables, only use a diode test lamp or a voltme-
ter.
Test lamps with an illuminant take up voltages which are too high and which can dam-
age the vehicle's electronic system.
When making electrical connections, ensure that:
they are not kinked or twisted
they do not rub on edges
they are not laid in sharp edged ducts without protection.
Insulate all connections.
Secure the cables against mechanical wear with cable binders or insulating tape,
for example to existing cables.
CAM60ADR-IO-16s.book Seite 11 Donnerstag, 7. Juli 2016 1:21 13
Scope of delivery CAM60ADR
EN
12
The camera is watertight in accordance with IP69K. The seals on the camera can therefore
withstand a high-pressure cleaner. Nevertheless, keep a distance of at least 50 cm between
the nozzle of the high pressure cleaner and the camera.
Always observe the following instructions when handling the camera:
Do not open the camera, as this impairs the sealing and the function of the camera (fig. 4,
page 4).
Do not pull at the cables, as this impairs the sealing and the function of the camera (fig. 5,
page 4).
The camera is not suitable for submerged operation.
3Scope of delivery
4 Accessories
Available as accessory (not included in scope of delivery):
5Intended use
The CAM60ADR camera (ref. no. 9600000057) is designed primarily for use in vehicles under
extreme conditions. It can be used in video systems to observe the space around the vehicle from
the driver's seat when manoeuvring or parking, for example.
CAM60ADR is compliant to ADR and can be used in vehicles for transport of hazardous goods.
!
No. in
fig. 6,
page 5
Quantity Description Reference no.
1 1 CAM60ADR (compliant to ADR) 9600000057
2 1 Camera bracket 9102200166
32Side covers
––Fastening material
Description Reference no.
Heavy duty system cable 20 m, compliant to ADR 9102200071
WARNING!
Risk of injury!
Since rear view systems are designed merely as an additional aid for reversing, it does
not relieve you of the duty to take proper care when reversing.
CAM60ADR-IO-16s.book Seite 12 Donnerstag, 7. Juli 2016 1:21 13
CAM60ADR Technical description
EN
13
6 Technical description
The camera with integrated microphone, which is encased in aluminium housing, transmits image
and sound to a monitor via a cable. The infrared LEDs improve night vision.
The camera transmits the image as if you are looking in the rear mirror.
The camera consists of the following main elements:
7 Information on the electrical connections
7.1 Laying cables
A
Please observe the following instructions:
As far as possible, use original openings or alternative openings for the connecting cable duct,
e.g. the paneling edges, ventilation grilles or blank panels. If no openings are available, you
must drill holes for the cables. Check beforehand that there is sufficient room for the drill head
to come out on the other side.
Wherever possible lay cables inside the vehicle, as they are better protected inside than outside
the vehicle.
If you do need to lay a cable outside the vehicle, ensure that it is well secured (use additional
cable ties, insulating tape, etc.).
To prevent damage to the cables, when laying them ensure that there is sufficient distance to
hot or moving vehicle components (exhaust pipes, drive shafts, light systems, fans, heater,
etc.). Use corrugated piping or other protective materials to protect against mechanical wear.
Screw on the plug connections of the connecting cables to protect against water penetration
(fig. e, page 7).
No. in
fig. 7,
page 5
Description
16-pin connection cable
2Infrared LEDs
3Microphone
NOTICE! Risk of damage!
To prevent damage, when drilling ensure that there is sufficient space on the other
side for the drill head to come out.
Cables and connections which are not properly installed will cause malfunctions or
damage to components. Correct installation of cables and connections is the basic
prerequisite for lasting and trouble-free operation of the retrofitted components.
The cables may not be exposed for long periods to solvents such as benzine, as the
solvents can damage the cable.
CAM60ADR-IO-16s.book Seite 13 Donnerstag, 7. Juli 2016 1:21 13
Mounting the camera CAM60ADR
EN
14
When laying electric connections, ensure that
They are not kinked or twisted
They do not rub on edges
They are not laid in sharp edged ducts without protection (fig. 3, page 4)
Attach the cables securely in the vehicles to prevent tripping hazards. Use cable binders,
insulating tape or glue the cables in place.
Protect every through-hole made in the bodywork against water penetration, e.g. by using a
cable with a sealant and by spraying the cable and the the cable sleeve with sealant.
I
8 Mounting the camera
8.1 Tools required
For installation and assembly you will require the following tools:
Drill bit set (fig. 1 1, page 3)
Drill (fig. 1 2, page 3)
Screwdriver (fig. 1 3, page 3)
Set of ring or open-ended spanners (fig. 1 4, page 3)
Measuring ruler (fig. 1 5, page 3)
Hammer (fig. 1 6, page 3)
Centre punch (fig. 1 7, page 3)
To make and test the electrical connection, the following tools are required:
Diode test lamp (fig. 1 8, page 3) or voltmeter (fig. 1 9, page 3)
Insulating tape (fig. 1 11, page 3)
Cable bushing sleeves, if necessary
To fasten the cables you may require additional cable binders.
NOTE
Do not start sealing the through-holes until all installation work has been finished for the
camera, and the required cable lengths have been established.
CAM60ADR-IO-16s.book Seite 14 Donnerstag, 7. Juli 2016 1:21 13
CAM60ADR Mounting the camera
EN
15
8.2 Mounting the camera
!
I
Observe the following installation instructions:
To provide a suitable viewing angle, the camera must be attached at a height of at least 2 m.
Ensure that you have a firm place from which to work when mounting the camera.
Ensure that the installation location of the camera is sufficiently firm (e.g. to prevent the camera
from being knocked down by branches that may brush over the roof of the vehicle).
Mount the camera bracket horizontally and in the middle of the rear of the vehicle (fig. 8,
page 6).
The most secure type of attachment is with screws fitted through the body. Please observe the
following instructions:
There must be sufficient space for the mounting procedure behind the chosen installation
location.
Suitable measures must be taken to prevent water penetrating through any holes made
(e.g. by using screws and sealant and/or spraying the outer attachment parts with a
sealant).
The location on the body where you wish to attach the camera must be rigid enough to
allow the camera to be tightly fastened.
Check beforehand that there is sufficient room for the drill head to come out on the other side
(fig. 2, page 4).
If you are not sure about the location you have chosen, consult the vehicle manufacturer or
dealer.
I
When mounting the camera, proceed as follows:
Hold the camera on the chosen location and mark at least two different points for the drill holes
(fig. 9, page 6).
Using a hammer and centre punch, gently pre-punch the previously marked points to prevent
the drill head from slipping off.
CAUTION!
Select a location for the camera and attach it so securely that it cannot under any
circumstances fall off and injure bystanders (e.g. by being knocked off by branches
brushing over the roof of the vehicle).
NOTE
If installing the camera alters the vehicle height or length specified in the vehicle
documents, your vehicle must be inspected by the appropriate authorities.
Make sure that you are in possession of documents verifying that your vehicle has
passed this inspection.
NOTE
We recommend greasing the threads of the bolts to prevent corrosion.
CAM60ADR-IO-16s.book Seite 15 Donnerstag, 7. Juli 2016 1:21 13
Mounting the camera CAM60ADR
EN
16
If you want to screw on the camera with self-tapping screws (fig. 0, page 6)
A
Drill Ø 4 mm holes at the points you have just marked.
Deburr all drill holes and apply rust-protection.
Screw the camera bracket on with the 5 x 20 mm self-tapping screws.
If you would like to attach the camera with threaded screws fitted through the
construction (fig. a, page 6)
A
Drill Ø 6.5 mm holes at the points you have just marked.
Deburr all drill holes and apply rust-protection.
Screw the camera bracket on with the M5 x 20 mm threaded screws.
Depending on the thickness of the construction, you may require longer threaded screws.
Creating a through-hole for the camera connection cable (fig. b, page 6)
I
A
Drill a hole of Ø 16 mm near the camera.
Deburr all drill holes that have been made in the sheet metal and apply rust-protection.
Place cable sleeves in all sharp edged ducts.
NOTICE! Risk of damage!
The holder may only be attached to steel panels with a minimum thickness of 1.5 mm
using self-tapping screws.
NOTICE! Risk of damage!
Ensure that that nuts cannot be pulled through the body shell when they are tightened.
Use larger washers or metal plates if necessary.
NOTE
If possible, use available openings – such as ventilation grilles – to feed the connection
cables through. If there are no existing openings, you must drill a hole with a
16 mm diameter.
NOTICE! Risk of damage!
Ensure that there is sufficient space on the other side for the drill head to come out
CAM60ADR-IO-16s.book Seite 16 Donnerstag, 7. Juli 2016 1:21 13
CAM60ADR Mounting the camera
EN
17
Mounting the camera
A
Push the camera into the camera bracket.
Attach the camera loosely with the two screws M3 x 8 mm in the slots (fig. c, page 6).
Align the camera provisorily so that the lens is at an angle of approx. 50° to the perpendicular
axis of the vehicle (fig. d, page 7).
A
Connecting the camera
I
Guide the camera cable into the vehicle interior.
Insert the plug of the camera cable into the socket of the extension cable.
Screw on the plug connections of the connecting cables to protect against water penetration
(fig. e, page 7).
Aligning the camera
I
Use the monitor image to align the camera:
The monitor image should show the bottom edge of the rear or the bumper of your
vehicle (A). The middle of the bumper should be in the middle of the screen. (fig. g,
page 7).
Check the function of the camera after you have connected it to a monitor.
NOTICE! Risk of damage!
Only use the screws supplied to mount the camera in the camera bracket.
Longer screws will damage the camera.
NOTICE! Risk of damage!
Never mount the camera without the camera guard.
NOTE
Lay the camera cable so that should you need to remove the camera, you can access
the plug connection between the camera and the extension cable easily. This con-
siderably eases dismantling work.
To minimise corrosion in the plug, apply a small amount of grease – such as pin
grease – inside the plug.
Additional extension cables are available on request (see chapter “Accessories” on
page 12).
NOTE
If necessary before aligning the camera connect the camera to a monitor and to a
power supply (see connecting diagram, fig. f, page 7
CAM60ADR-IO-16s.book Seite 17 Donnerstag, 7. Juli 2016 1:21 13
Cleaning and caring for the camera CAM60ADR
EN
18
Fastening the camera
Thighten the two screws in the slots of the camera bracket.
Mount the side covers with the two screws M3 x 8 mm in the middle drill holes (fig. h,
page 8).
9 Cleaning and caring for the camera
A
Clean the camera with a soft, damp cloth from time to time.
10 Guarantee
The statutory warranty period applies. If the product is defective, please contact the
manufacturer's branch in your country (see the back of the instruction manual for the addresses) or
your retailer.
For repair and guarantee processing, please send the following items:
Defect components
A copy of the receipt with purchasing date
A reason for the claim or description of the fault
11 Disposal
Place the packaging material in the appropriate recycling waste bins wherever possible.
M
If you wish to finally dispose of the product, ask your local recycling centre or specialist
dealer for details about how to do this in accordance with the applicable disposal regu-
lations.
NOTICE! Risk of damage!
Do not use sharp or hard objects to clean the device as these may damage the device.
CAM60ADR-IO-16s.book Seite 18 Donnerstag, 7. Juli 2016 1:21 13
CAM60ADR Technical data
EN
19
12 Technical data
Approvals
The device has E13 certification.
PerfectView CAM 60ADR
Ref. no.: 9600000057
Image sensor: 1/3" CCD
Pixels: Approx. 290,000 pixels
Video standard: PAL, 1 Vpp
Sensitivity: < 0.5 lux
Viewing angle: Approx. 69° vertical
Approx. 92.5° horizontal
Approx. 120° diagonal
Operating voltage: 11 – 16 Vg
Consumption: 4.8 W
Operating temperature: –30 °C bis +70 °C
Protection class: IP69K
Vibration resistance: 10 g
Dimensions W x H x D
(with bracket):
80 x 75 x 62 mm
Weight: Approx. 0.3 kg
E
CAM60ADR-IO-16s.book Seite 19 Donnerstag, 7. Juli 2016 1:21 13
Erklärung der Symbole CAM60ADR
DE
20
Bitte lesen Sie diese Anleitung vor Einbau und Inbetriebnahme sorgfältig durch und
bewahren Sie sie auf. Geben Sie sie im Falle einer Weitergabe des Produktes an den
Nutzer weiter.
Inhaltsverzeichnis
1 Erklärung der Symbole. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
2 Sicherheits- und Einbauhinweise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3 Lieferumfang . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
4 Zubehör . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
5 Bestimmungsgemäßer Gebrauch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
6 Technische Beschreibung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
7 Hinweise zum elektrischen Anschluss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
8 Kamera montieren . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
9 Kamera pflegen und reinigen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
10 Gewährleistung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
11 Entsorgung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
12 Technische Daten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
1 Erklärung der Symbole
!
!
A
I
WARNUNG!
Sicherheitshinweis: Nichtbeachtung kann zu Tod oder schwerer Verletzung führen.
VORSICHT!
Sicherheitshinweis: Nichtbeachtung kann zu Verletzungen führen.
ACHTUNG!
Nichtbeachtung kann zu Materialschäden führen und die Funktion des Produktes
beeinträchtigen.
HINWEIS
Ergänzende Informationen zur Bedienung des Produktes.
CAM60ADR-IO-16s.book Seite 20 Donnerstag, 7. Juli 2016 1:21 13
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188

Dometic CAM60ADR Istruzioni per l'uso

Tipo
Istruzioni per l'uso
Questo manuale è adatto anche per