Keithley 168-20 Manuale utente

Marca: Keithley

Modello: 168-20

Tipo: Manuale utente

SPECIFICATIONS MODEL 168-20

SPECIFICATIONS

Input Limit: * range not to exceed 1999 mA.3

Maximum current: (mAs ran%a) 3000 ma nor. to axcaed .66 saeanh duratio

Tracking sate: Gr~aCer than 3000 ma per miciosecand for rated accuracy

2 0375

MODEL 168-20 GENERAL INFORMATION

!( .

SECTION 1. GENERAL INFORMATION

0375 3

‘INITIAL PREPARATION

SECTION 2. INITIAL PREPARATION

Same as 168, however check zero end adjust if necessery.

--__

The 168-20 m.Ae mere= should be used for making tie meeeuremen~e on

x-ray machines only by people who ere fully familiar~with the mechiae

involved and the hazards rssocieted vich tie meenuremente. *n error

in meas”I‘ement technique could result in lethal shock hezards. --

.-.. -I_

_ .,. .---~.-

MODEL 168-20 OPERATING INSTRUCTIONS

SECTION 3. OPERATING INSTRUCTIONS

.Ae a mm:

Place mAs-NOSN switch to NORM Qosftion. than refer to Wade1

168 manual for OMM operation.

Ae e mA8 Meter: Refer to Model 168 manual for power selecrion details.

Place nuts-NORM switch to m&s. For the o-1999 mAe range.

depress (DC) and (A). Depress the erase button to redec

the unit to 0 mAs and use the erase button whenever a

resee is desired.

Connection LO X-Ray Machines: l”ne 168-20 rr& meter is specifically

designed for use with x-ray machines in the O-1999 WAS range. me m~8

meter muse be connected in series with the x-ray machine’s high voltage

secondary, between the secondary winding and ground. as ehovn In Figure

1. -Hose x-my machines have labeled ma or mAs fese poinrs for this

purpaee.

r-----y --1

PIGlmE 1. Connection to X-Ray High Voltage Secondary,

0375 5

___-___ ..- .~ --- -~ -.__

OP!DATINC INSTRUCTIONS HODEL 168-20

WARNING

Consult r-ray machine service manual for proper hook up. since

improper connections can result in lethal voltages present on the

168-20 and damage to the meter. NEVER connect 168-20 co “high”

side of the secondary. This will result in destruction of the

meter and a dangerous shock hazard. Never touch any part of the

wment circuit with Lhe high voltage on.

& over voltage protection device should be securely fasrened across rbe

ma or ntAs test points exrernally or internally LO protect both machines

and,che qperator in the event of an open circuit LO the m~8 meter (i.e..

teat lead falling off, blown fuge. etc.). Suitable procecrion devicea

include power resistors, epark gaps, etc. Specific information concernidg

protection devices should be obtained from the manufacturer of the x-ray

machine in quearion.

Figure 2 s@~s an alternate measurement technique for meesuring r&s. A

shunt resistor is securely installed across rhe ma or tie test points and

the 168-20 is used in the inre$raring voltege mode. Integrating voltage

mode is selected by pldcing the m&-NORM witch in the mAe position and

depressing (DC).

The shunt resistor should be wire wound, with a parer raring adequate for

the machine’s l~aximum current.

m Shunt Reeiecor

0 * 199.9 * 10 n

0 + 1999 rk4.a 1n

0 * 19990 * .1 n

This technique provides greater safety. multiple ranges. and greater in-

put overload prorectioo or& the 168-20.

6 0325

MODEL 168-20 OPERATING lNSTR"CTIO:iS

L- Other Uses: The 168-20 has 3 usable integrating ranges. ae fallows:

Function Setting (mAs/NOSN in mAa) FCa*g*

* (DC) (A) 0 - 1999 a.9

* 0 - 1.999 *

"e 0 - 1.999 ve

NOTE

Tie law mAs range bes 1000 ohm series re8is~ance, and should not be

used far x-ray tia measurements. The volt-second range can be

transformed into an mAa range by use of a sbunr resistor.

r---- ----

IO-MEG. I I I I

TUBE

0375:

F1aw.E 2. Int~graring Voltage Mae

----.-. ~..--..

MAqmNANCE MODEL 168-20

SECTION 4. MAINTENANCE

For All OEM Punctions: Refer CO Model 168 manual.

PAR Xetcr Leakage Tese:

Perform

DC voltage zero check and zero adjust-

menc if nece8sary as outlined in Model 168 manual. Place meter in mAs

mode rich input open. reset vith erase buecon. Release button and time

drift WiLh a SLOp YBLCh. Drift should t,e less than 1 dig,t per ten

seconds. If drift is greater than this, repeat zero ad,usLnent.

Pas Meter Accuracy Test: Connecr mAs meter in mAs mode to a Keirhley 227

or other current source adjusted for a 10.11 ma output. ~.eset the m~s

meter and. With a stop uacch. measure the time interval for the mAe

rehding co infrease from 100 mAa LO 1100 U.S. ‘nmelapsed time should be

100 sec. fl eec.

0375

Keithley 168-20 Manuale utente

Marca: Keithley

Modello: 168-20

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: Keithley 168-20 User manual

Keithley 168-20 Manuale utente

Keithley 168-20 Manuale utente

in altre lingue

Altri documenti